0% found this document useful (0 votes)
2 views

Arduino Code Smart Bin 2

The document outlines the materials required to create an Arduino Smart Dustbin, including an Arduino Nano, ultrasonic sensor, and servo motor. It also references links to purchase the necessary components. Additionally, it mentions related posts about Arduino projects such as a car parking system and other Arduino code examples.
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
2 views

Arduino Code Smart Bin 2

The document outlines the materials required to create an Arduino Smart Dustbin, including an Arduino Nano, ultrasonic sensor, and servo motor. It also references links to purchase the necessary components. Additionally, it mentions related posts about Arduino projects such as a car parking system and other Arduino code examples.
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Arduino Smart Dustbin

- January 07, 2023

Arduino Smart Dustbin

Materials Required:-
Plastic Waste Bin: - https://amzn.to/3GoDhIi

MDF Board: - https://amzn.to/3IyKB6U

Arduino Nano: -https://amzn.to/3Zlpk6i

Ultrasonic Sensor: - https://amzn.to/3GKJ2kK

9G Servo Motor: - https://amzn.to/3VSKHcq

9V HW Battery: - https://amzn.to/3jZFemU

Jumper Wires :- https://amzn.to/3ihQpHd

25V 2200uf Capacitor:- https://amzn.to/3yLfjTT

Comments

Popular posts from this blog

Arduino Code Car Parking System

- March 07, 2024

// Created by Simple Circuits #include <Wire.h> #include <LiquidCrystal_I2C.h> LiquidCrystal_I2C


lcd(0x27,16,2); #include <Servo.h> Servo myservo; int IR1 = 2; int IR2 = 3; int Slot = 4; //Total
number of parking Slots int flag1 = 0; int flag2 = 0; void setup() { Serial.begin(9600); lcd.init();
//initialize the lcd lcd.backlight(); //open the backlight pinMode(IR1, INPUT); pinMode(IR2,
INPUT); myservo.attach(4); myservo.write(100); lcd.setCursor (0,0); lcd.print(" ARDUINO ");
lcd.setCursor (0,1); lcd.print(" PARKING SYSTEM "); delay (2000); lcd.clear(); } void loop(){
if(digitalRead (IR1) == LOW && flag1==0){ if(Slot>0){flag1=1; if(flag2==0){myservo.write(0); Slot =
Slot-1;} }else{ lcd.setCursor (0,0); lcd.print(" SORRY :( "); lc...

Read more

Arduino Code

- February 16, 2024

//define Pins #include <Servo.h> Servo servo; int trigPin = 11; int echoPin = 12; // defines variables
long duration; int distance; void setup() { servo.attach(13); servo.write(180); delay(2000); //
Sets the trigPin as an Output pinMode(trigPin, OUTPUT); // Sets the echoPin as an Input
pinMode(echoPin, INPUT); } void loop() { // Clears the trigPin digitalWrite(trigPin, LOW);
delayMicroseconds(2); // Sets the trigPin on HIGH state for 10 micro seconds digitalWrite(trigPin,
HIGH); delayMicroseconds(10); digitalWrite(trigPin, LOW); // Reads the echoPin, returns the sound
wave travel time in microseconds duration = pulseIn(echoPin, HIGH); // Calculating the distance
distance= duration*0.034/2; // Prints the distance on the Serial Monitor Serial.print("Distance: ");
Serial.println(distance); if ( distance <= 25 ) // Change Distance according to Ultrasonic Sensor
Placement { servo.write(180); delay(3000); ...

Read more

Circuit Diagram
- February 16, 2024

You might also like