Jimma
Jimma
Remove flag
Question text
In a network synthesis, which transform method is used to realize a desired network
function using passive components.
a.
Laplace transform
b.
Z-transform
c.
Fourier series
d.
Fourier transform
Feedback
The correct answer is: Laplace transform
Question 2
Incorrect
Mark 0.00 out of 1.00
Remove flag
Question text
Consider a two-port network consists of one inductor of 1-Henry, and one resistor of 2-
ohms. If the inductor is connected in series with the first port, and the resistor is
connected in parallel with the second port, what is the value of the transfer impedance
function Z_21 (s)?
a.
s(s+2)
b.
s+2
c.
2(s+2)
d.
s
Feedback
The correct answer is: s(s+2)
Question 3
Incorrect
Mark 0.00 out of 1.00
Remove flag
Question text
Which of the following defines channel capacity according to Shannon’s theorem?
a.
The maximum power a channel can handle
b.
The level of noise in a channel
c.
The maximum data rate that can be transmitted over a channel without error
d.
The minimum bandwidth required for transmission
Feedback
The correct answer is: The maximum data rate that can be transmitted over a channel
without error
Question 4
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which type of transistor has the highest current gain?
a.
Both have the same current gain
b.
Neither has a current gain
c.
PNP
d.
NPN
Feedback
The correct answer is: NPN
Question 5
Correct
Mark 1.00 out of 1.00
Remove flag
Question text
Cache memory acts between
a.
None of these
b.
CPU and Hard Disk
c.
CPU and RAM
d.
RAM and ROM
Feedback
The correct answer is: CPU and RAM
Question 6
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What is the primary characteristic of a fading channel?
a.
Variation in signal strength over time
b.
Continuous additive
c.
Constant power loss
d.
Fixed phase shift
Feedback
The correct answer is: Variation in signal strength over time
Question 7
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What does bandwidth (BW) in a communication system refer to?
a.
The power of a transmitted signal
b.
The range of frequencies a system can transmit or receive
c.
The amount of data a system can process
d.
The noise level in a system
Feedback
The correct answer is: The range of frequencies a system can transmit or receive
Question 8
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following is a characteristic of a RISC (Reduced Instruction Set Computer)
architecture?
a.
Large instruction set
b.
Variable-length instructions
c.
Simple and fixed-length instructions
d.
Complex instructions
Feedback
The correct answer is: Simple and fixed-length instructions
Question 9
Incorrect
Mark 0.00 out of 1.00
Remove flag
Question text
For a three-phase induction motor, maximum torque is double the full load torque and
starting torque is 1.6 times the full load torque. To get a full load slip of 5%, percentage
reduction in the rotor resistance should be?
a.
62.7%
b.
35%
c.
75%
d.
60%
Feedback
The correct answer is: 62.7%
Question 10
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
When connecting transmission line conductors, what is the recommended method to
ensure a secure connection?
a.
Welding
b.
Crimping
c.
Taping
d.
Soldering
Feedback
The correct answer is: Crimping
Question 11
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What is the primary variable that describes the flow of electric charge in a circuit?
a.
Capacitance
b.
Voltage
c.
Current
d.
Resistance
Feedback
The correct answer is: Current
Question 12
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Determine the odd component of the signal: x(t) = cost + sint.
a.
2cost
b.
2sint
c.
cost
d.
sint
Feedback
The correct answer is: cost
Question 13
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which of the following represents the maximum amount of memory that can be
addressed by a 32-bit processor?
a.
1 GB
b.
8 GB
c.
4 GB
d.
2 GB
Feedback
The correct answer is: 4 GB
Question 14
Correct
Mark 1.00 out of 1.00
Flag question
Question text
In Java, which keyword is used to create a subclass?
a.
extends
b.
implements
c.
extend
d.
inherit
Feedback
The correct answer is: extends
Question 15
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
A half wave rectifier has a 200Vrms of source voltage and step-down transformer with a
turn ratio of 4:1. What will be the average voltage across the load ignoring the voltage
drop across the diode
a.
100V
b.
31.8V
c.
50.4V
d.
70.7V
Feedback
The correct answer is: 31.8V
Question 16
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following statements correctly distinguishes the multiple access techniques
FDMA, TDMA, CDMA, and OFDMA?ASK and FSK
a.
FDMA allocates different frequencies to users, TDMA assigns unique codes to users,
CDMA uses different time slots, and OFDMA combines frequency and time division.
b.
FDMA and TDMA both allocate different frequencies to users, CDMA assigns time slots
to users, and OFDMA splits the bandwidth into orthogonal sub-carriers for each user.
c.
FDMA allocates different time slots to users, TDMA uses different frequencies, CDMA
assigns unique codes to users, and OFDMA splits the bandwidth into orthogonal sub-
carriers for each user.
d.
FDMA allocates different frequencies to users, TDMA allocates different time slots to
users, CDMA assigns unique codes to users, and OFDMA splits the bandwidth into
orthogonal sub-carriers for each user.
Feedback
The correct answer is: FDMA allocates different frequencies to users, TDMA allocates
different time slots to users, CDMA assigns unique codes to users, and OFDMA splits the
bandwidth into orthogonal sub-carriers for each user.
Question 17
Correct
Mark 1.00 out of 1.00
Remove flag
Question text
The air-gap flux density waveform has decreased flux under one pole tip and measured
under the other is due to __________
a.
saturation of iron magnetic circuit
b.
demagnetization
c.
magnetization
d.
cross magnetization
Feedback
The correct answer is: cross magnetization
Question 18
Correct
Mark 1.00 out of 1.00
Flag question
Question text
A three phase, 50 Hz induction motor has a full load speed of 1440 rpm. Speed of the
rotor field w.r.t. rotor structure is?
a.
6.28 rad/s
b.
150 rad/s
c.
145 rad/s
d.
157 rad/s
Feedback
The correct answer is: 6.28 rad/s
Question 19
Correct
Mark 1.00 out of 1.00
Flag question
Question text
In nodal analysis, which of the following is typically calculated?
a.
Node voltages
b.
Power dissipation
c.
Mesh currents
d.
Total circuit resistance
Feedback
The correct answer is: Node voltages
Question 20
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
The plant transfer function is given by G(s)=1⁄(s²+s) with unity negative feedback. Use a
PD controller such that undamped natural frequency is 4rad⁄sec and damping ratio is 0.2
to have the desired system response. Find the proportional and derivative gain
respectively.
a.
0.8 and 12
b.
12 and 0.8
c.
16 and 0.6
d.
0.6 and 16
Feedback
The correct answer is: 16 and 0.6
Question 21
Correct
Mark 1.00 out of 1.00
Flag question
Question text
For a power system having induction motor loads, an overexcited synchronous motor is
also attached. Then the overall power factor __________
a.
improves
b.
becomes under power factor
c.
remains same
d.
degrades
Feedback
The correct answer is: improves
Question 22
Incorrect
Mark 0.00 out of 1.00
Remove flag
Question text
If a decimal number 101.25 is converted to binary, what is the correct binary
representation?
a.
1100101.01000
b.
1100101.100
c.
1100101.11
d.
1100101.01
Feedback
The correct answer is: 1100101.01
Question 23
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
In a continuous-time physical system, memory is directly associated with
a.
Storage of energy
b.
Number of components in the system
c.
Storage registers
d.
Time
Feedback
The correct answer is: Storage of energy
Question 24
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Kirchhoff’s Voltage Law (KVL) states that:
a.
The total current entering a junction equals the total current leaving the junction.
b.
Power consumed in a circuit is equal to the power supplied.
c.
The sum of all voltages around a closed loop is zero.
d.
Voltage is directly proportional to resistance.
Feedback
The correct answer is: The sum of all voltages around a closed loop is zero.
Question 25
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
An 8-bit synchronous up-counter is designed to count from 0 to 255. If the counter
needs to be modified to count from 50 to 200, which of the following changes would be
the most efficient approach?
a.
Redesign the counter using a 7-bit structure
b.
Modify the initial count to 50 and the final count to 200
c.
Implement the counter using a microcontroller with a programmable counter
d.
Add additional logic gates to the existing 8-bit counter
Feedback
The correct answer is: Add additional logic gates to the existing 8-bit counter
Question 26
Correct
Mark 1.00 out of 1.00
Flag question
Question text
How does inheritance promote code reusability in object-oriented programming?
a.
All of the above
b.
It allows objects to share common functionalities.
c.
It simplifies complex programs into smaller modules.
d.
It eliminates the need for duplicate code.
Feedback
The correct answer is: All of the above
Question 27
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Suppose the Karnaugh map cells for a 4-input logic function have values 1 for A'B'C'D,
A'B'CD, A'BC'D', A'BCD', ABC'D', ABCD', AB'C'D and AB'CD. Which of the following
Boolean expressions correctly represents the simplified function?
a.
F = A'B' + AB
b.
F=A⊕B⊕C
c.
F = B'D + BD'
d.
F = A'C + BC'
Feedback
The correct answer is: F = B'D + BD'
Question 28
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
When the excitation voltage is increased from 1 to 1.3 pu of a 3-phase synchronous
motor. Then load angle for the constant power operation __________
a.
increased
b.
decreased
c.
can also be increased
d.
must be decreased
Feedback
The correct answer is: must be decreased
Question 29
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which of the following systems is stable?
a.
y(t) = exp(x(t))
b.
y(t) = log(x(t))
c.
y(t) = sin(x(t))
d.
y(t) = tx(t) + 1
Feedback
The correct answer is: y(t) = sin(x(t))
Question 30
Correct
Mark 1.00 out of 1.00
Flag question
Question text
How many input combinations are possible for a 3-input logic gate?
a.
4
b.
3
c.
8
d.
2
Feedback
The correct answer is: 8
Question 31
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Imagine you have a class called "Animal" with a method "makeSound()". How can you
achieve polymorphism using inheritance for a specific animal like a "Dog"?
a.
Create a static method "makeSound()" within the "Dog" class.
b.
Override the "makeSound()" method in the "Dog" class.
c.
Declare the "makeSound()" method as abstract in "Animal".
d.
Use overloading to define multiple "makeSound()" methods.
Feedback
The correct answer is: Override the "makeSound()" method in the "Dog" class.
Question 32
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What role does corona discharge play in the performance analysis of transmission lines,
cables, and overhead line insulators?
a.
It enhances mechanical strength
b.
It reduces insulation resistance
c.
It indicates high conductor temperature
d.
It causes power losses and interference
Feedback
The correct answer is: It causes power losses and interference
Question 33
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What might be a consequence of neglecting the effect of line capacitance in a long-
distance high-voltage transmission system?
a.
Underestimation of line losses
b.
Incorrect voltage regulation
c.
Overestimation of inductive reactance
d.
Increased thermal efficiency
Feedback
The correct answer is: Overestimation of inductive reactance
Question 34
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which of the following is a type of architecture used in the computers nowadays?
a.
System Design
b.
Von-Neumann Architecture
c.
Harvard Architecture
d.
Microarchitecture
Feedback
The correct answer is: Von-Neumann Architecture
Question 35
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
The transfer function of a simple RC network functioning as s controller is given by
Gϲ(s)=(s+z₁)⁄(s+p₁). The required condition for the RC network to act as a phase lead
controller is
a.
p₁<z₁
b.
p₁>z₁
c.
None of these.
d.
p₁=z₁
Feedback
The correct answer is: p₁>z₁
Question 36
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
How would you determine the appropriate spacing between towers during the
installation of overhead transmission lines?
a.
By using standard spacing guidelines provided by manufacturers
b.
By consulting local regulations
c.
By calculating the expected maximum conductor sag
d.
By estimating the average wind speed in the area
Feedback
The correct answer is: By calculating the expected maximum conductor sag
Question 37
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following is the boolean operator for logical-and in C++?
a.
$$
b.
&
c.
&&
d.
$
Feedback
The correct answer is: &&
Question 38
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which statement best describes the impact of a multipath channel on signal
transmission?
a.
Multipath channels increase signal power.
b.
Multipath channels ensure a clear line-of-sight transmission.
c.
Multipath channels eliminate noise.
d.
Multipath channels cause multiple delayed copies of the signal to arrive at the receiver.
Feedback
The correct answer is: Multipath channels cause multiple delayed copies of the signal to
arrive at the receiver.
Question 39
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which circuit analysis method is generally considered the most systematic for solving
any type of circuit?
a.
Ohm's Law
b.
Mesh Analysis
c.
Nodal Analysis
d.
Thevenin's Theorem
Feedback
The correct answer is: Nodal Analysis
Question 40
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Determine the nature of the system: y[n] = x[n]x[n – 1] with unit impulse function as an
input.
a.
Dynamic, output always 1, invertible
b.
Dynamic, output always 1, invertible
c.
Static, output always zero, non-invertible
d.
Dynamic, output always zero, non-invertible
Feedback
The correct answer is: Dynamic, output always zero, non-invertible
Question 41
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What will be the output of the following C++ code
a.
Compilation error
b.
0
c.
1:0
d.
1
Feedback
The correct answer is: 1
Question 42
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What is the characteristic of a good control system?
a.
Insensitive to the input command
b.
Sensitive to parameter variation
c.
Insensitive to the parameter variation but sensitive to the input commands
d.
Neither sensitive to parameter variations nor sensitive to input commands
Feedback
The correct answer is: Insensitive to the parameter variation but sensitive to the input
commands
Question 43
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
The inductance and capacitance of a 400kV. Three-phase. 50Hz lossless transmission
lines are 1.6mH/km/phase and 10nF km phase respectively. The sending end voltage is
maintained at 400kV. To maintain a voltage of 400kV at the receiving end, when the line
is delivering a 300MW load, the shunt compensation required is…...
a.
Resistive
b.
Zero
c.
Inductive
d.
Capacitive
Feedback
The correct answer is: Inductive
Question 44
Correct
Mark 1.00 out of 1.00
Flag question
Question text
C++ programs start their execution from ______________?
a.
begin()
b.
main()
c.
start()
d.
output()
Feedback
The correct answer is: main()
Question 45
Correct
Mark 1.00 out of 1.00
Flag question
Question text
A desirable modulation scheme provides ….. Bit error rate at …. received signal to noise
ratios
a.
Low, High
b.
Low, Low
c.
High, High
d.
High, Low
Feedback
The correct answer is: Low, High
Question 46
Correct
Mark 1.00 out of 1.00
Flag question
Question text
How does a transistor amplify signals in a semiconductor device?
a.
By increasing resistance
b.
None of the above
c.
By decreasing resistance
d.
By controlling current flow
Feedback
The correct answer is: By controlling current flow
Question 47
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What is the primary advantage of OFDMA over FDMA, TDMA, and CDMA in modern
communication systems?
a.
OFDMA eliminates the need for time synchronization between users.
b.
OFDMA minimizes the need for complex code assignment algorithms.
c.
OFDMA provides better spectral efficiency by allowing multiple users to share the same
frequency band through orthogonal sub-carriers.
d.
OFDMA allows for dynamic time slot allocation to users.
Feedback
The correct answer is: OFDMA provides better spectral efficiency by allowing multiple
users to share the same frequency band through orthogonal sub-carriers.
Question 48
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which type of diode is commonly used in radio frequency (RF) detection circuits due to
its low forward voltage drop and fast switching characteristics?
a.
Schottky diode
b.
Light-emitting diode (LED)
c.
Varactor diode
d.
Zener diode
Feedback
The correct answer is: Schottky diode
Question 49
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Variable can be defined as _________ .
a.
String that have a predefined meaning
b.
All
c.
Represent constant data that cannot be changed during program execution
d.
Named memory location that stores a specific data type
Feedback
The correct answer is: Named memory location that stores a specific data type
Question 50
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which of the following for loop syntax is not correct?
a.
for(; ;)
b.
for (x=0;x!=1;)
c.
for(; ; ;)
d.
for(;x<10;)
Feedback
The correct answer is: for(; ; ;)
Question 51
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Compare and contrast the concepts of abstraction and encapsulation in OOP design.
a.
Encapsulation deals with objects, while abstraction deals with classes.
b.
Both are the same concept with different names.
c.
Abstraction focuses on data hiding, while encapsulation hides implementation details.
d.
Encapsulation creates abstract data types, while abstraction defines essential
functionalities.
Feedback
The correct answer is: Encapsulation creates abstract data types, while abstraction
defines essential functionalities.
Question 52
Correct
Mark 1.00 out of 1.00
Flag question
Question text
________is used to represent the absence of a returned value?
a.
double
b.
int
c.
short
d.
void
Feedback
The correct answer is: void
Question 53
Correct
Mark 1.00 out of 1.00
Flag question
Question text
A 4-bit binary number 1001 is applied to the inputs of a 4-bit adder circuit with the
carry-in of 1. What is the output of the adder circuit?
a.
1001
b.
1010
c.
1100
d.
1101
Feedback
The correct answer is: 1010
Question 54
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which one of the following is Not True about semiconductor materials
a.
The band gap energy of semiconductors are very high
b.
Current is due to the movement of both majority and minority carriers
c.
They have negative temperature coefficient
d.
Doping semiconductors with impurity increase their conductivity
Feedback
The correct answer is: The band gap energy of semiconductors are very high
Question 55
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What is Fourier series?
a.
The representation of non-periodic signals in a mathematical manner is called a Fourier
series
b.
The representation of periodic signals in a mathematical manner is called a Fourier
series
c.
The representation of non-periodic signals in terms of complex exponentials or
sinusoids is called a Fourier series
d.
The representation of periodic signals in terms of complex exponentials or sinusoids is
called a Fourier series
Feedback
The correct answer is: The representation of periodic signals in terms of complex
exponentials or sinusoids is called a Fourier series
Question 56
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The impedance in an AC circuit is a combination of:
a.
Resistance and capacitance
b.
Inductance and capacitance
c.
Resistance, inductance, and capacitance
d.
Resistance and inductance
Feedback
The correct answer is: Resistance, inductance, and capacitance
Question 57
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What will be the output of the following C++ code?
a.
Compiler error may be possible
b.
Return memory address held by variable a
c.
0
d.
1
Feedback
The correct answer is: 0
Question 58
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The leakage current in CE arrangement is_____________ that in CB arrangement.
a.
less than
b.
equal to
c.
none of the above
d.
greater than
Feedback
The correct answer is: greater than
Question 59
Correct
Mark 1.00 out of 1.00
Flag question
Question text
If the addition result of two BCD numbers is invalid, which of the following is the
correction mechanism?
a.
Adding a binary number 0110
b.
Diminishing the result
c.
Voiding the two numbers
d.
Subtracting the binary number 0110
Feedback
The correct answer is: Adding a binary number 0110
Question 60
Correct
Mark 1.00 out of 1.00
Flag question
Question text
For an energy signal
a.
P=0
b.
E=∞
c.
E=0
d.
P=∞
Feedback
The correct answer is: P = 0
Question 61
Correct
Mark 1.00 out of 1.00
Flag question
Question text
While using the direct mapping technique, in a 16 bit system the higher order 5 bits are
used for ________
a.
Id
b.
Word
c.
Block
d.
Tag
Feedback
The correct answer is: Tag
Question 62
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following is a unit of electrical resistance?
a.
Ampere
b.
Volt
c.
Ohm
d.
Watt
Feedback
The correct answer is: Ohm
Question 63
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
The total amount of work done during execution, in a given time is referred to as
a.
Execution time
b.
Response time
c.
Through put
d.
Delay time
Feedback
The correct answer is: Through put
Question 64
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
If one of the phases of RST supply gets broken, then the temperature rise of the
induction motor _________
a.
increases
b.
reduces as compared to the normal operating temperature
c.
reduces to temperature rise of corresponding single phase induction motor
d.
remains same as before
Feedback
The correct answer is: remains same as before
Question 65
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Why is it important to understand electrical safety when working with circuits?
a.
To increase the speed of circuit assembly
b.
To ensure efficient circuit performance
c.
To prevent injury and equipment damage
d.
To reduce the cost of electrical components
Feedback
The correct answer is: To prevent injury and equipment damage
Question 66
Correct
Mark 1.00 out of 1.00
Flag question
Question text
At a very low speed, increase in field resistance will _________
a.
not have significant effect on speed
b.
no effect
c.
increase the speed of motor
d.
decrease the speed of motor
Feedback
The correct answer is: decrease the speed of motor
Question 67
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What is the primary advantage of a Chebyshev filter over a Butterworth filter?
a.
Simplicity in designing
b.
Flatter passband.
c.
Steeper roll-off
d.
No passband ripple
Feedback
The correct answer is: Steeper roll-off
Question 68
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Given that X(s) is the Laplace transform of the signal cos 2t u (t). The time signal
corresponding to (s + 1) X(s) is ________
a.
(cos 2t + (sin2t)/2) u (t)
b.
(cos 2t – 2 sin 2t) u (t)
c.
(cos 2t – (sin2t)/2)) u (t)
d.
(cos 2t + 2 sin 2t) u (t)
Feedback
The correct answer is: (cos 2t – 2 sin 2t) u (t)
Question 69
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following statement is Not True about comparison between operation of
bipolar junction transistor (BJT) and a field-effect transistor (FET) in semiconductor
devices?
a.
FET has less power consumption than BJT
b.
FET has more temperature stability than BJT
c.
FET has higher gain than BJT
d.
FET have high input impedance than BJT
Feedback
The correct answer is: FET has higher gain than BJT
Question 70
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Let a driving-point impedance is given as Z(s)=(s^2+2s+2)/(s^2+s+1). If it is realized in
a Cauer-I form, what will be the type and value of the first network element?
a.
A resistor of 1-ohm connected in series.
b.
A capacitor of 1-F connected in parallel.
c.
An inductor of 2-H connected in parallel.
d.
An inductor of 1-H connected in series.
Feedback
The correct answer is: A resistor of 1-ohm connected in series.
Question 71
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
By increasing the transmission voltage to double of its original value the same power
can be dispatched keeping the line loss ……….
a.
double the original value
b.
one-fourth of the original value
c.
equal to its original value
d.
half of the original value
Feedback
The correct answer is: one-fourth of the original value
Question 72
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What is the role of the Socket class in Java networking?
a.
It represents a client-side connection to a network
b.
It provides methods to manage threads
c.
It provides methods to read and write files
d.
It represents a server-side connection to a network
Feedback
The correct answer is: It represents a client-side connection to a network
Question 73
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The hybrid parameter h_21 in a two port network is known as:
a.
Input impedance
b.
Reverse voltage gain
c.
Output admittance
d.
Forward current gain
Feedback
The correct answer is: Forward current gain
Question 74
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
If the height of the transmission tower is increased…….
a.
The line capacitance will decrease but line inductance will remain unchanged
b.
The line capacitance will decrease and the line inductance will increase
c.
The line capacitance and inductance will not change
d.
The line capacitance will increase but the line inductance will decrease
Feedback
The correct answer is: The line capacitance will decrease but line inductance will remain
unchanged
Question 75
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Given the following class definition, what is the correct way to access the private variable
'age'?
a.
person.age();
b.
person.getAge();
c.
person.age;
d.
person->getAge();
Feedback
The correct answer is: person.getAge();
Question 76
Correct
Mark 1.00 out of 1.00
Flag question
Question text
According to Ohm's Law, the voltage (V) across a resistor (R) when a current (I) flows
through it is given by:
a.
V = I^2*R
b.
V = I*R
c.
V = I/R
d.
V = R/I
Feedback
The correct answer is: V = I*R
Question 77
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which one of the following is a characteristic of band-pass filter?
a.
Pass frequencies within a certain range and attenuate frequencies outside that range.
b.
Pass all the frequencies
c.
Attenuate all the frequencies
d.
Pass the frequencies below a certain cutoff.
Feedback
The correct answer is: Pass frequencies within a certain range and attenuate frequencies
outside that range.
Question 78
Correct
Mark 1.00 out of 1.00
Flag question
Question text
If the characteristic equation of the closed loop system is s²+2s+2=0, then the system is:
a.
Underdamped
b.
Over damped
c.
Undamped
d.
Critically damped
Feedback
The correct answer is: Underdamped
Question 79
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following statements is true about constructors in Java?
a.
Constructors have a return type
b.
Constructors can be overloaded
c.
Constructors can be abstract
d.
Constructors can be inherited
Feedback
The correct answer is: Constructors can be overloaded
Question 80
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which of the following is the most important consideration when designing a digital
logic circuit?
a.
Cost and resource utilization
b.
Appearance and aesthetics
c.
Sensitivity to input signals
d.
Personal preference of the designer
Feedback
The correct answer is: Sensitivity to input signals
Question 81
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which one of the following is incorrect?
a.
The addition of open loop poles pulls the root locus towards the right and system
becomes unstable.
b.
The main objective of drawing root locus plot is to obtain a clear picture about the open
loop poles and zeros of the system.
c.
Root locus is used to calculate relative stability.
d.
The main objective of drawing root locus plot is to obtain a clear picture about the
transient response of feedback system for various values of open loop gain k.
Feedback
The correct answer is: The main objective of drawing root locus plot is to obtain a clear
picture about the open loop poles and zeros of the system.
Question 82
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
In a series R-L-C network, at resonance frequency, the impedance of the network is:
a.
Equal to X_L
b.
Equal to R
c.
Equal to 0
d.
Equal to X_C
Feedback
The correct answer is: Equal to R
Question 83
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Quadrature amplitude modulation (QAM) is a combination of -------
a.
ASK and FSK
b.
All of the above
c.
PSK and FSK
d.
ASK and PSK
Feedback
The correct answer is: ASK and PSK
Question 84
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Data hazards occur when EE
a.
Greater performance loss
b.
Some functional unit is not fully pipelined
c.
Pipeline changes the order of read/write access to operands
d.
Machine size is limited
Feedback
The correct answer is: Pipeline changes the order of read/write access to operands
Question 85
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Consider a unity negative feedback system with the forward transfer function given by
G(s)=1⁄s⁴+2s³+3s²+4s+4. Which of the following is incorrect about the system?
a.
The system is unstable and all poles lies on right half of s-plane.
b.
The system is unstable and the steady state error is 0.8 for unit step input.
c.
The system is unstable and there are two poles on right half of s-plane.
d.
The system is unstable and type zero.
Feedback
The correct answer is: The system is unstable and all poles lies on right half of s-plane.
Question 86
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which one of the following is wrong?
a.
Signal flow graphs are reliable to find transfer function than block diagram reduction
technique.
b.
The transfer function of the system is defined as the ratio of Laplace transform of output
to Laplace transform of input considering initial conditions zero.
c.
The overall transfer function from block diagram reduction for cascaded blocks is
product of individual gain.
d.
The overall transfer function of two blocks in parallel are product of individual gain.
Feedback
The correct answer is: The overall transfer function of two blocks in parallel are product
of individual gain.
Question 87
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which of the following scenarios best illustrates polymorphism?
a.
A method defined in a class being accessed using an object
b.
A method defined in a superclass and overloaded in a subclass
c.
A subclass providing a specific implementation of a method that is already defined in its
superclass
d.
A class having multiple constructors
Feedback
The correct answer is: A subclass providing a specific implementation of a method that
is already defined in its superclass
Question 88
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Which parameter is most critical when analyzing the mechanical strength of
transmission line cables?
a.
Material conductivity
b.
Tensile strength
c.
Voltage rating
d.
Diameter
Feedback
The correct answer is: Tensile strength
Question 89
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Mesh analysis is based on which of the following laws?
a.
Kirchhoff’s Voltage Law (KVL)
b.
Ohm's Law
c.
Kirchhoff’s Current Law (KCL)
d.
Faraday's Law
Feedback
The correct answer is: Kirchhoff’s Voltage Law (KVL)
Question 90
Correct
Mark 1.00 out of 1.00
Flag question
Question text
What will be the output of the following C++ code
a.
200 50
b.
90 "" 400
c.
90 400
d.
200 "" 50
Feedback
The correct answer is: 200 50
Question 91
Correct
Mark 1.00 out of 1.00
Flag question
Question text
The width of the data bus determines:
a.
The number of bits the CPU can process at a time
b.
The clock speed of the CPU
c.
The size of the cache memory
d.
The number of instructions the CPU can execute per second
Feedback
The correct answer is: The number of bits the CPU can process at a time
Question 92
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
A waveform is given by v(t) = 10 sin2π 100 t. The magnitude of the second harmonic in
its Fourier series representation is
a.
200 V
b.
0V
c.
100 V
d.
20 V
Feedback
The correct answer is: 0 V
Question 93
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following network parameters are referred to as "Short circuit
parameters?"
a.
H-parameters
b.
Z-parameters
c.
Y-parameters
d.
Transmission parameters
Feedback
The correct answer is: Y-parameters
Question 94
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
When designing a clocked sequential circuit, which of the following is the most
important initial step?
a.
Referring example and replicating it
b.
Determine the state transition diagram
c.
Implement the circuit using logic gates
d.
Analyze the timing requirements of the system
Feedback
The correct answer is: Referring example and replicating it
Question 95
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
What is the ROC of the system function H(z) if the discrete time LTI system is BIBO
stable?
a.
None of the mentioned
b.
Entire z-plane, except at z=0
c.
Contain unit circle
d.
Entire z-plane, except at z=∞
Feedback
The correct answer is: Contain unit circle
Question 96
Correct
Mark 1.00 out of 1.00
Flag question
Question text
If a two-port network is reciprocal, which condition must hold true?
a.
Z_11=Z_22
b.
Y_12=Y_21
c.
h_11=h_12
d.
A=D
Feedback
The correct answer is: Y_12=Y_21
Question 97
Correct
Mark 1.00 out of 1.00
Flag question
Question text
A string insulator has 4 units. The voltage across the bottom most unit is 33.33% of the
total voltage. Its string efficiency is……
a.
66.67%
b.
25%
c.
33.33%
d.
75%
Feedback
The correct answer is: 66.67%
Question 98
Correct
Mark 1.00 out of 1.00
Flag question
Question text
Which of the following FET configuration permits operating points with positive values
of VGS , where the levels of ID that exceed IDSS.
a.
D-MOSFET
b.
P channel JFET
c.
N channel JFET
d.
E-MOSFET
Feedback
The correct answer is: D-MOSFET
Question 99
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
Suppose flowchart is used to illustrate a program that calculates the area of a shape.
which symbol should be used to represent the flow of execution?
a.
Diamond
b.
Oval
c.
Rectangle
d.
Arrow
Feedback
The correct answer is: Arrow
Question 100
Incorrect
Mark 0.00 out of 1.00
Flag question
Question text
A 100KW, 250 V, 400 A, a long shunt compound generator has an armature resistance of
0.025 ohms. There are 1000 shunt fields turns per pole and 3 series field turns per pole.
The series field is connected in a such a fashion that positive armature current produces
direct-axis MMF which adds to that of the shunt field. Compute the gross MMF at the
rated terminal current when shunt field current is 4.7A and speed is 1150 rpm.
a.
4.7AT
b.
3.5AT
c.
5.9AT
d.