For the latest prices, please check AutomationDirect.com.

1-800-633-0405

Standard PLC
Built-in I/O Specifications - Inputs
C0-01DD1-D $139.00 Inputs per Module 8 (Sink/Source)
Operating Voltage Range 24VDC
8 DC Input/6 Sinking DC Output Micro PLC
Input Voltage Range 21.6–26.4 VDC
X1-2: Typ 5mA @ 24VDC
Input Current
X3-8: Typ 4mA @ 24VDC
Wiring Diagram
X1-2: 6.0 mA @ 26.4 VDC
Maximum Input Current
C0-01DD1-D 24VDC X3-8: 5.0 mA @ 26.4 VDC
X1-2: 4.7 kΩ @ 24VDC
Input Impedance
X3-8: 6.8 kΩ @ 24VDC

+
X1-2: > 19VDC
ON Voltage Level

+
X3-8: > 19VDC
PWR
X1-2: < 4VDC
RUN OFF Voltage Level
ERR
X3-8: < 7VDC
X1-2: 4.5 mA

+
Minimum ON Current
X3-8: 3.5 mA

+
PORT1
TX1 X1-2: 0.1 mA
Maximum OFF Current
RX1 X3-8: 0.5 mA
X1-2: Typ 5µs Max 20µs
L OFF to ON Response
TX2
X3-8: Typ 2ms Max 10ms
RX2 L
X1-2: Typ 5µs Max 20µs
PORT2 L 5 - 27VDC ON to OFF Response
+

X3-8: Typ 3ms Max 10ms

L
PORT3
RS-485 Status Indicators Logic Side (8 points, green LED)
TX3
L Commons 2 (4 points/common) Isolated
+

L 24VDC
+

Built-in I/O Specifications - Outputs

RX3
5 - 27VDC

Outputs per Module 6 (Sink)

Operating Voltage Range 5–27 VDC
Output Voltage Range 4–30 VDC
NOTE: When using Standard PLCs, you must use CLICK
0.1 A/point; C3: 0.4 A/common, C4:
programming software version V1.20 or later. Maximum Output Current
0.2 A/common
Equivalent Input Circuit Minimum Output Current 0.2 mA
Internal Module Circuitry
Maximum Leakage Current 0.1 mA @ 30.0 VDC
On Voltage Drop 0.5 VDC @ 0.1 A
INPUT
X1-X4
Optical Isolator
Maximum Inrush Current 150mA for 10ms
+ Typical
Y1: typ 5µs; max 20µs
OFF to ON Response
+
24 VDC Y2-6: < 0.5 ms
Y1: typ 5µs; max 20µs
C1 COM ON to OFF Response
Y2-6: < 0.5 ms
To X2-X4
commons Status Indicators Logic Side (6 points, red LED)
INPUT
X5-X8
Optical Isolator
Commons 2 (4 points/com & 2 points/com)
+ Typical
External DC Power 20–28 VDC Maximum @ 60mA
+
24 VDC
Required (All Points On)
C2 COM
C0-01DD1-D General Specifications
To X6-X8
commons
Current Consumption at 24VDC 140mA
Equivalent Output Circuit Terminal Block Replacement Part No. C0-16TB
Internal Module Circuitry
Drawing Link PDF
24 VDC
+ +V
Optical Isolator Weight 5.0 oz [140g]
OUTPUT
+
L
Y1
C0-01DD1-D Temperature Derating Chart ZIPLink Pre-Wired PLC
Connection Cables and Modules
High response
5 - 27 VDC
* circuit

8
Inputs
6
Outputs ZL-RTB20 20-pin
Points

Optical Isolator
4
feed-through
* connector module
OUTPUT
+ Y2-Y4
L
5 - 27 VDC * 2

C3 COM
0
0 10 20 30 40 50 55 °C
32 50 68 85 104 122 131 °F
Optical Isolator
OUTPUT Surrounding Temperature (°C/°F)
+ Y5-Y6
L * Use every other input/output.
5 - 27 VDC
*
20-pin connector cable
ZL-C0-CBL20 (0.5 m length)
C4 COM
ZL-C0-CBL20-1 (1.0 m length)
Note: C3 & C4 are not internally connected.
ZL-C0-CBL20-2 (2.0 m length)
* Zener Diode Power Dissipation: 200 mW

www.automationdirect.com CLICK PLCs tCLP-85

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Specifications

General Specifications General Specifications
For All CLICK PLC Analog, analog combo I/O modules only:

Products
32°F to 140°F [0°C to 60°C];
Operating Temperature All other modules:
32°F to 131°F [0°C to 55°C],
These general specifications apply to IEC 60068-2-14 (Test Nb, Thermal Shock)
all CLICK PLCs and optional power
supply products. Please refer to the –4°F to 158°F [–20°C to 70°C]
IEC 60068-2-1 (Test Ab, Cold)
appropriate I/O temperature derating Storage Temperature
IEC 60068-2-2 (Test Bb, Dry Heat)
charts under both the PLC and I/O IEC 60068-2-14 (Test Na, Thermal Shock)
module specifications to determine
Ambient Humidity 30% to 95% relative humidity (non–condensing)
best operating conditions based on the
ambient temperature of your particular Environmental Air No corrosive gases. Environmental pollution level is 2 (UL840)
application. MIL STD 810C, Method 514.2, EC60068-2-27, Category [f],
Vibration Procedure[VIII]
JIS C60068-2-27 (Sine wave vibration test)
MIL STD 810C, Method 516.2, IEC60068-2-27,
Shock
JIS C60068-2-27, Category [f], Procedure[VIII]
<EN61131-2>
EN61000-4-2 (ESD)
EN61000-4-3 (RFI)
EN61000-4-4 (FTB)
EN61000-4-5 (Surge)
Noise Immunity EN61000-4-6 (Conducted)
EN61000-4-8 (Power frequency magnetic field immunity)

<Local Test>
Impulse noise 1μs, 1000V
RFI: No interference measured at 150 and 450 MHz (5w/15cm)
Emissions EN55011:1998 Class A; EN61000-6-4:2007+A1:2011
UL508, UL61010-2-201 (File No. E157382, E316037); CE (EN61131-
Agency Approvals
2); CUL Canadian C22.2
Other RoHS 2011/65/EU Amendment (EU)2015/863

www.automationdirect.com CLICK PLCs tCLP-77

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Specifications

PLC Unit Specifications

Basic, Standard and Analog PLC Unit Specifications

Basic PLC Standard PLC Analog PLC
Stored Program/Cyclic Stored Program/Cyclic Stored Program/Cyclic
Control Method
execution method execution method execution method
I/O Numbering System Fixed in Decimal Fixed in Decimal Fixed in Decimal
Ladder Memory (steps) 8000 8000 8000
Total Data Memory (words) 8000 8000 8000
Contact Execution (Boolean) < 0.6 us < 0.6 us < 0.6 us
Typical Scan (1K Boolean) 1-2 ms 1-2 ms 1-2 ms
RLL Ladder Style Programming Yes Yes Yes
Run Time Edits No No No
Scan Variable / fixed Variable / fixed Variable / fixed
CLICK Programming Software
Yes Yes Yes
for Windows
Yes (two RS-232 ports and Yes (two RS-232 ports and
Built-in Communication Ports Yes (two RS-232 ports)
one RS-485 port) one RS-485 port)
Protocols Protocols: Modbus RTU (master/slave) and ASCII (in/out)
FLASH Memory Standard on PLC Standard on PLC Standard on PLC
Built-in Discrete I/O points 8 inputs, 6 outputs 8 inputs, 6 outputs 4 inputs, 4 outputs
Built-in Analog I/O Channels No No 2 inputs, 2 outputs
Number of Instructions Available 21 21 21
Control Relays 2000 2000 2000
System Control Relays 1000 1000 1000
Timers 500 500 500
Counters 250 250 250
Interrupts Yes (external: 8 / timed: 4) Yes (external: 8 / timed: 4) Yes (external: 4 / timed: 4)
Subroutines Yes Yes Yes
For/Next Loops Yes Yes Yes
Math (Integer and Hex) Yes Yes Yes
Drum Sequencer Instruction Yes Yes Yes
Internal Diagnostics Yes Yes Yes
Password Security Yes Yes Yes
System Error Log Yes Yes Yes
User Error Log No No No
Memory Backup Super Capacitor Super Capacitor + Battery Super Capacitor + Battery
Yes (battery sold separately; Yes (battery sold separately;
Battery Backup No
part # D2-BAT-1) part # D2-BAT-1)
Calendar/Clock No Yes Yes
I/O Terminal Block Replacement AutomationDirect p/n C0-16TB AutomationDirect p/n C0-16TB AutomationDirect p/n C0-16TB
Communication Port & Terminal
N/A AutomationDirect p/n C0-3TB AutomationDirect p/n C0-3TB
Block Replacement
24VDC Power Terminal Block
AutomationDirect p/n C0-4TB AutomationDirect p/n C0-4TB AutomationDirect p/n C0-4TB
Replacement

www.automationdirect.com CLICK PLCs tCLP-78

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK Specifications
CLICK PLC Hardware/Software Compatibility
CLICK PLCs require a minimum software version of v2.50 for the PID function. The
table below shows the most recent software and hardware versions required for the
High-Speed input operation capability to be accessible.

CLICK PLC Features Software Compatibility

Minimum CLICK Software Version
CPU Type Part Number
Hardware High-Speed Inputs EtherNet/IP PID DHCP
C0-00DD1-D
C0-00DD2-D
Basic v1.00 N/A N/A N/A N/A
C0-00DR-D
C0-00AR-D
C0-01DD1-D
C0-01DD2-D
Standard v1.20 N/A N/A N/A N/A
C0-01DR-D
C0-01AR-D
C0-02DD1-D (before SN 171208001) v1.12
C0-02DD1-D (after SN 171208001) v2.10
C0-02DD2-D (before SN 174018001) v1.12
Analog N/A N/A N/A N/A
C0-02DD2-D (after SN 174018001) v2.10
C0-02DR-D (before SN 173158001) v1.12
C0-02DR-D (after SN 173158001) v2.10
Ethernet CPUs Ethernet CPUs require v2.40 for EtherNet/IP communications
C0-10DD1E-D
C0-10DD2E-D v2.30
Ethernet Basic v2.00 v2.40 v2.50 v3.00
C0-10DRE-D
C0-10ARE-D N/A
C0-11DD1E-D
C0-11DD2E-D v2.30
Ethernet Standard v2.00 v2.40 v2.50 v3.00
C0-11DRE-D
C0-11ARE-D N/A
C0-12DD1E-D
C0-12DD2E-D v2.30
C0-12DRE-D
C0-12ARE-D N/A
C0-12DD1E-1-D
C0-12DD2E-1-D v2.30
Ethernet Analog v2.20 v2.40 v2.50 v3.00
C0-12DRE-1-D
C0-12ARE-1-D N/A
C0-12DD1E-2-D
C0-12DD2E-2-D v2.30
C0-12DRE-2-D
C0-12ARE-2-D N/A
C0-08NE3
v1.20
C0-16NE3
C0-04AD-1
C0-04AD-2
C0-04DA-1
C0-04DA-2
C0-4AD2DA-1
I/O Modules C0-4AD2DA-2 v1.40 N/A N/A N/A N/A
C0-04RTD
C0-04THM
C0-08CDR
C0-16CDD1
C0-16CDD2
C0-04POT v3.70
Other modules v1.00

www.automationdirect.com CLICK PLCs tCLP-80

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Family Overview

What you’ll need
Of course, what you’ll need for your 1. Select your CLICK or CLICK PLUS PLC unit.
system depends on your particular
application, but this overview shows you
what you’ll need for a simple system.

2. If using a CLICK PLUS PLC, select an Option

C2-14D1

IN 24V
C1
1
2

6.5mA
Slot Module if desired.
3
4
C2
5
6
7
8

OUT 5-27V
C3
1
2
3

0.1A
4
C4
5
6
+V

3. If you need additional I/O, select from 24 different

types of Stackable I/O modules.

4. Select a 24VDC power supply.

or

5. Download the FREE CLICK

programming software.
support.automationdirect.com/
products/clickplcs.html

6. Download the FREE CLICK mobile app.

The CLICK mobile app is available for iOS and
Android. It can connect to your C2-02CPU or
C2-03CPU over Bluetooth to provision the PLC
onto a Wi-Fi network. (PLC requires an external
antenna)

www.automationdirect.com CLICK PLCs tCLP-11

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

CLICK PLC Family Overview

What you’ll need (continued)

7. Select your PC-to-PLC programming cable.

If your PC has a USB port, use cable EA-MG-PGM-CBL to connect to the PLC port. If your PC has a 9-pin serial
communications port, use programming cable D2-DSCBL. If your PC has an Ethernet port, use C5E-STPYL-C3
(crossover) or C5E-STPYL-S3 (straight through) Ethernet cable. If your PC is on a network with a wireless access
point, you can connect using one of our Wi-Fi anteannas.

D2-DSCBL
USB-CBL-AMICB6 C5E-STPYL-C3 (crossover)
C5E-STPYL-S3 (straight through)

(PC requires RS-232 port

For Ethernet PLC Unit
to use this cable)

USB A to USB microB or

Programming Cable Assembly
(CLICK PLUS Only) SE-ANT250 or
Wi-Fi/Bluetooth Dome Antenna
(C2-02CPU & C2-03CPU only)
EA-MG-PGM-CBL

Connects to PC USB Port

or
SE-ANT210
Wi-Fi/Bluetooth Whip Antenna
(C2-02CPU & C2-03CPU only)
(nonmetal enclosure only)

8. Select tools, wire, and provide power.

Screwdriver Wire Strippers Hookup Wire

TW-SD-MSL-2 DN-WS

www.automationdirect.com CLICK PLCs tCLP-12

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Power Supplies
Power Supplies CLICK 24VDC Power Supply Ratings
The CLICK PLC family offers two 24VDC power Part Number Output Current Price
supplies. They are identical except for the output C0-00AC 0.5 A $51.00
current. C0-01AC 1.3 A $63.00
It is not mandatory to use one of these CLICK
power supplies for the CLICK/CLICK PLUS PLC C0-00AC
system. You can use any other 24VDC power
Power Supply Input Specifications
supply that Automationdirect.com offers, Part Number C0-00AC C0-01AC
including the PSP24-DC12-1 12 to 24 VDC Input Voltage Range 85–264 VAC
converter shown below. Input Frequency 47–63 Hz
C0-00AC Power Supply Input Current (typical)
0.3 A @ 100VAC, 0.9 A @ 100VAC,
Limited auxiliary AC power supply allows you to 0.2 A @ 200VAC 0.6 A @ 200VAC
power the 24VDC CLICK C0 and C2 series PLCs Inrush Current 30A
with 100–240 VAC supply power. The 0.5 A DC Efficiency 80% typical
power supply is capable of controlling the PLC
plus a limited configuration based on the power
budget of each I/O module. The C0-00AC is
Power Supply Output Specs
a low-cost solution for applications requiring Part Number C0-00AC C0-01AC
only minimal I/O and power consumption. This Output Voltage Range 23–25 VDC
power supply will not support a fully-populated Output Current 0.5 A 1.3 A
CLICK PLC system with all possible I/O module Ripple 200mV p-p max (0–55°C)
combinations. C0-01AC Ripple Noise 300mV p-p max (0–55°C)
C0-01AC Power Supply Over Current Protection
@ 0.65 A @ 1.6 A
Expanded auxiliary AC power supply allows you (automatic recovery) (automatic recovery)
to power the 24VDC CLICK C0 and C2 series PLCs Over Voltage Protection @ 27.6 V (clamped by Zener diode)
with 100–240 VAC supply power. The 1.3 A DC Start-up Time 1000ms max at rated input and load
power supply is capable of supporting a fully- Hold-up Time 10ms minimum at 85VAC, I=max
populated CLICK PLC system with all possible I/O
module
combinations, with no concerns for exceeding the Power Supply General Specs
power budget. Part Number C0-00AC C0-01AC
PSP24-DC12-1 DC-DC Converter Ambient Operating
32–131°F [0–55°C]
With this DC-DC converter you can operate the Temperature
CLICK/CLICK PLUS PLC with 12VDC input power. Storage Temperature -4–158°F [-20–70°C]
Humidity 30–95%, non-condensing
Vibration Resistance JIS C60068-2-6, sine wave vibration
Shock Resistance JIS C60068-2-27
Voltage Withstand
CLICK Power Supply CLICK PLC Input-Output 1500VAC, 5mA cutoff current
Input-Ground 1500VAC, 5mA cutoff current
Output-Ground 500VAC, 5mA cutoff current
Insulation Resistance
Input-Output 10MΩ minimum, 500VDC
Input-Ground 10MΩ minimum, 500VDC
Output-Ground 5MΩ minimum, 500VDC
Noise Immunity FCC Class A, EN55022:1998 Class A
5P terminal block, Fujicon UF2362AX
Input/Output Interface
series or equivalent
UL508, UL1604, EN61010-1 (IEC 1010-1),
Agency Approvals
CAN/CSA E60079-15:02, JIS C0025
Drawing Link PDF PDF
Weight 5.3 oz [150g] 6.0 oz [170g]

PSP24-DC12-1 DC-DC Converter Specs

24V Input Voltage Range 9.5–18 VDC
0V Input Power (no load) 1.0 W max.
Startup Voltage 8.4 VDC
G Undervoltage Shutdown 7.6 VDC
Output Voltage Range 24–28 VDC (adjustable)
Output Current 1.0 A
Short Circuit Protection Current limited at 110% typical
24VDC power is supplied to the PLC unit through wiring
connected from the power supply output to the 4-pin 24VDC Drawing Link PDF
input connector located on the bottom of the PLC unit. Weight 7.5 oz [213g]

PSP24-DC12-1
www.automationdirect.com CLICK PLCs tCLP-18
 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Power Budgeting
Power Budgeting
There are two factors to consider when determining the It is strongly recommended that the power source for the logic
power required to operate a CLICK PLC system. The first is side be separate from the power source for the field side to help
the power required by the PLC and internal logic-side power eliminate possible electrical noise.
provided through the PLC. This includes the CPU’s own Power budgeting requires the calculation of the total current the
I/O, any connected I/O modules that are powered through 24VDC power source needs to provide to CLICK’s logic side. A
the PLC expansion port, plus any device, such as a C-more separate calculation is required to determine the total current
Micro-Graphic panel, that is powered through one of the required for all devices operating from the field side of the
communications ports. PLC system.
The second area is the power required by all externally- Refer to the Power Budgeting example shown on the following
connected I/O devices. This should be viewed as the field-side page. The table shows required current for a CLICK PLUS PLC,
power required. The field-side power is dependent on the two I/O modules, and a C-more Micro. Use the total amperage
voltage used for a particular input or output device as it relates values to select a suitable power supply.
to the wired I/O point and to the calculated load rating of the
connected device.

CLICK 24VDC Power Supply Other 24VDC Power Supply

C0-00AC or C0-01AC Example: PSP24-060S

Power Consumption for Power Consumption for

CLICK and CLICK PLUS PLC Units CLICK PLUS Option Slot
Modules
PLC Current Consumption (mA) PLC Current Consumption (mA) CLICK PLUS
Power Budget External Power Budget External Option Slot Modules
Part Number 24VDC 24VDC Part Number 24VDC 24VDC
(Logic Side) (Field Side) (Logic Side) (Field Side) Current Consumption (mA)
Basic PLC Units Ethernet Analog PLC Units Power Budget External
C0-00DD1-D 120 60 Part Number 24VDC 24VDC
C0-12DD1E-D 60 (Logic Side) (Field Side)
C0-00DD2-D 140
C0-12DD2E-D Option Slot I/O Modules
C0-00DR-D 120 0
C0-12DRE-D 0 C2-14D1 50 60
C0-00AR-D 160
C0-12ARE-D C2-14D2 50 0
Standard PLC Units
C0-12DD1E-1-D 60 C2-14DR 75 0
C0-01DD1-D 140 60 140 C2-14AR 75 0
C0-01DD2-D C0-12DD2E-1-D
C2-14TTL 220 0
C0-01DR-D 140 0 C0-12DRE-1-D 0
160 C2-08D1-4VC 80 60
C0-01AR-D C0-12ARE-1-D C2-08D2-4VC 80 0
Analog PLC Units C0-12DD1E-2-D 60
140 C2-08DR-4VC 100 0
C0-02DD1-D 140 60
C0-12DD2E-2-D C2-08AR-4VC 100 0
C0-02DD2-D
140 0 C0-12DRE-2-D 160 0 C2-08D1-6C 80 60
C0-02DR-D
C0-12ARE-2-D 140 C2-08D2-6C 80 0
Ethernet Basic PLC Units
CLICK PLUS PLCs C2-08DR-6C 100 0
C0-10DD1E-D 120 60
C2-01CPU 110 C2-08AR-6C 100 0
C0-10DD2E-D
C2-01CPU-2 120 C2-08D1-6V 80 60
C0-10DRE-D 120 0
C2-02CPU 105 C2-08D2-6V 80 0
C0-10ARE-D 0
C2-02CPU-2 115 C2-08DR-6V 100 0
Ethernet Standard PLC Units
C2-03CPU 130 C2-08AR-6V 100 0
C0-11DD1E-D 140 60
C2-03CPU-2 140 Option Slot Intelligent Modules
C0-11DD2E-D
C2-DCM 60 0
C0-11DRE-D 140 0
C2-NRED 125 0
C0-11ARE-D
C2-OPCUA 125 0
www.automationdirect.com CLICK PLCs tCLP-19
 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Power Budgeting
Power Consumption for CLICK Stackable I/O Modules
I/O Module Current I/O Module Current Consumption
Consumption (mA) (continued) (mA)
Power Budget External Power Budget External
Part Number 24VDC 24VDC Part Number 24VDC 24VDC
(logic side) (field side) (logic side) (field side)
Discrete Input Modules Discrete Combo I/O Modules
C0-08SIM 50 0 C0-16CDD1 80 50
C0-16CDD2 80 0
C0-08ND3 30 0
C0-08CDR 80 0
C0-08ND3-1 30 0
Analog Input Modules
C0-16ND3 40 0 C0-04AD-1 20 65
C0-08NE3 30 0 C0-04AD-2 23 65
C0-16NE3 40 0 C0-04POT 30 0
C0-08NA 30 0 C0-04RTD 25 0
Discrete Output Modules C0-04THM 25 0
C0-08TD1 50 15 Analog Output Modules
C0-04DA-1 20 145
C0-08TD2 50 0
C0-04DA-2 20 85
C0-16TD1 80 100
Analog Combo I/O Modules
C0-16TD2 80 0
C0-4AD2DA-1 25 75
C0-08TA 80 0 C0-4AD2DA-2 20 65
C0-04TRS 100 0 C-more Micro-Graphic Panel
C0-04TRS-10 120 0 Monochrome only 90 0
C0-08TR 100 0
C0-08TR-3 90 0

Power Supply PLC Unit I/O Module

(C0-01AC) (C2-03CPU) (C2-14D1)

I/O Module
(C0-16ND3) Power Budgeting Example

I/O Module Current Consumption (mA) Example

(C0-16TD1) Power Budget External
Port 2 Part Number 24VDC 24VDC
(logic side) (field side)
C2-03CPU 130 0
C2-14D1 50 60
C0-16ND3 40 0
C0-16TD1 80 100
C-more Micro 90 0
C-more Total: 390 160 *
Micro-Graphic
* Add in calculated load of connected I/O devices.
Panel
Only monochrome models
can be powered from port 2.
www.automationdirect.com CLICK PLCs tCLP-20
 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Wiring System for CLICK PLC Family

Wiring Solutions using the ZIPLink Wiring System
ZIPLinks eliminate the normally tedious process of wiring ZIPLinks are available in a variety of styles to suit your needs,
between devices by utilizing prewired cables and DIN rail including feedthrough connector module. ZIPLinks are available
mount connector modules. It’s as simple as plugging in a for all Basic, Standard and Ethernet CLICK PLC units, select
cable connector at either end or CLICK PLUS option slot modules, and
terminating wires at only one end. most discrete and analog stackable
Prewired cables keep installation I/O modules. Pre-printed I/O-specific
clean and efficient, using half the adhesive label strips for quick marking
space at a fraction of the cost of of ZIPLink modules are provided with
standard terminal blocks. ZIPLink cables.

Solution 1: CLICK PLC, CLICK PLUS PLC with Option Slot

Module, and Stackable I/O Modules to ZIPLink Connector
Modules
When looking for quick and easy I/O-to-field termination, a Use the “CLICK PLC PLC Unit ZIPLink Selector” table and
ZIPLink connector module used in conjunction with a prewired CLICK I/O ZIPLink selector tables located in this section:
ZIPLink cable, consisting of an I/O terminal block at one end and • Locate your PLC or I/O module.
a multi-pin connector at the other end, is the best solution.
• Select a ZIPLink Module.
• Select a corresponding ZIPLink Cable.

Solution 2: CLICK/CLICK PLUS PLC I/O to 3rd Party Devices

When wanting to connect PLC I/O (built-in, option slot module,
or stackable) to another device within close proximity, no extra
terminal blocks are necessary when using the ZIPLink Pigtail Use the I/O Modules to 3rd Party Devices selector tables
Cables. ZIPLink Pigtail Cables are prewired to an I/O terminal located in the ZIPLink section:
block with color-coded pigtail with soldered-tip wires on the
• Locate your PLC or I/O module.
other end.
• Select a ZIPLink Pigtail Cable that is
compatible with your 3rd party device.

Solution 3: GS Series and DuraPulse Drives Communication

Cables
Need to communicate via Modbus RTU to a drive or a network of
drives? Use the Drives Communication selector tables located in the
ZIPLink section:
ZIPLink cables are available in a wide range of configurations for
connecting to PLCs and SureServo, SureStep, Stellar Soft Starter • Locate your Drive and type of communications.
and AC drives. Add a ZIPLink communications module to quickly • Select a ZIPLink cable and other associated hardware.
and easily set up a multi-device network.

Solution 4: Serial Communications Cables

ZIPLink offers communications cables for use with CLICK PLCs
and select CLICK PLUS PLCs that can also be used with other Use the Serial Communications Cables selector table located
communications devices. Connections include a 6-pin RJ12 in the ZIPLink section:
connector which can be used in conjunction with the RJ12 • Locate your connector type
Feedthrough module. • Select a cable.

www.automationdirect.com CLICK PLCs tCLP-165

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Wiring System for CLICK PLC Family

CLICK PLC & CLICK PLUS Option Slot ZIPLink CLICK/CLICK PLUS PLC Discrete Input
Selector Module ZIPLink Selector
PLC or Option Slot Module ZIPLink I/O Module ZIPLink
CLICK PLUS # of Module Cable
# of Module Cable Input Module Component
CLICK PLC Unit Option Slot Component Terms Part No. Part No.
Terms Part No. Part No.
Module C0-08SIM Not supported by ZIPLink
C0-00DD1-D NA C0-08ND3
C0-00DD2-D NA C0-08ND3-1
C0-00DR-D NA 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-08NE3
C0-00AR-D NA ZL-RTB20, ZL-C0-CBL20 C0-08NA
20 Feedthrough
C0-01DD1-D NA ZL-RTB20-1 * Feedthrough ZL-RTB20
C0-01DD2-D NA C0-16ND3 20
Sensor ZL-LTB16-24-1
C0-01DR-D NA ZL-C0-CBL20 *
Feedthrough ZL-RTB20
C0-01AR-D NA C0-16NE3 20
Sensor ZL-LTB16-24-1
C0-02DD1-D NA
No ZIPLinks are available
C0-02DD2-D NA
for CLICK Analog PLC units.
C0-02DR-D NA CLICK/CLICK PLUS PLC Discrete Output
C0-10DD1E-D NA Module ZIPLink Selector
C0-10DD2E-D NA I/O Module ZIPLink
C0-10DRE-D NA Output # of Module Cable
Component
C0-10ARE-D NA Module Terms Part No. Part No.
ZL-RTB20, ZL-C0-CBL20 C0-08TD1
C0-11DD1E-D C2-14D1 20 Feedthrough
ZL-RTB20-1 *
C0-11DD2E-D C2-14D2 C0-08TD2 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-11DRE-D C2-14DR C0-08TR
C0-11ARE-D C2-14AR C0-08TR-3 Not supported by ZIPLink
NA C2-14TTL C0-08TA
C0-12DD1E-D C2-08D1-4VC Feedthrough ZL-RTB20
C0-12DD2E-D C2-08D2-4VC C0-16TD1 20 Fuse ZL-RFU20 2 ZL-C0-CBL20*
C0-12DRE-D C2-08DR-4VC Relay (sinking) ZL-RRL16-24-1
C0-12ARE-D C2-08AR-4VC Feedthrough ZL-RTB20
C0-12DD1E-1-D C2-08D1-6C Fuse ZL-RFU20 2
No ZIPLinks are available for C0-16TD2 20 ZL-C0-CBL20*
C0-12DD2E-1-D C2-08D2-6C Relay
CLICK Ethernet Analog PLC units or ZL-RRL16-24-2
C0-12DRE-1-D C2-08DR-6C (sourcing)
CLICK PLUS Option Slot Modules with analog I/O.
C0-12ARE-1-D C2-08AR-6C C0-04TRS1 20 Feedthrough ZL-RTB20 ZL-C0-CBL20*
C0-12DD1E-2-D C2-08D1-6V C0-04TRS-10 Not supported by ZIPLink
C0-12DD2E-2-D C2-08D2-6V
C0-12DRE-2-D C2-08DR-6V
CLICK/CLICK PLUS PLC Combo I/O Module
C0-12ARE-2-D C2-08AR-6V
C2-DCM
ZIPLink Selector
No ZIPLinks are available for I/O Module ZIPLink
NA C2-NRED
CLICK PLUS Option Slot Communications Module Combo # of Module Cable
C2-OPCUA Module Terms
Component
Part No. Part No.
C0-16CDD1
Table Notes: C0-16CDD2
20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
* Select the cable length by replacing the * with: Blank = 0.5 m, -1 = 1.0 m,
C0-08CDR 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
or -2 = 2.0 m.
1 Note: The C0-04TRS relay output is derated not to exceed 2A per point maximum
when used with the ZIPLink wiring system.
2 Note: Fuses (5x20 mm) are not included. See Edison Electronic Fuse section CLICK/CLICK PLUS PLC Analog I/O Module
for 5x20 mm fuse. S500 and GMA electronic circuit protection is recommended ZIPLink Selector
for fast-acting maximum protection. S506 and GMC electronic circuit protection is I/O Module ZIPLink
recommended for time-delay performance. Ideal for inductive circuits.
To ensure proper operation, do not exceed the voltage and current rating of the Analog # of Module Cable
Component
ZIPLink module. ZL-RFU20 = 2A per circuit. Module Terms Part No. Part No.
C0-04AD-1 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-04AD-2 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-04POT 0
No ZIPLinks are available for RTD and
C0-04RTD 20
thermocouple modules.
C0-04THM 11
C0-04DA-1 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-04DA-2 11 Feedthrough ZL-RTB20 ZL-C0-CBL11 *
C0-4AD2DA-1 20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *
C0-4AD2DA-2 20 Feedthrough ZL-RTB20 ZL-C0-CBL20 *

www.automationdirect.com CLICK PLCs tCLP-166

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Accessories
C2-USER-M $0.00 EA-MG-PGM-CBL $52.00 C0-3TB $10.00
CLICK PLUS PLC Hardware User Manual PC to Panel Programming Cable Spare 3-Pole Terminal Block
Assembly for C-more Micro-Graphic
Manual covers all CLICK PLUS PLC Replacement 3-pole terminal block for the
Panels and CLICK/CLICK PLUS PLCs
and I/O module installation and 3-wire RS-485 Port 3 on CLICK Standard
wiring, specifications, error codes and The 6-ft cable assembly connects a and Analog PLCs as well as the CLICK
troubleshooting guide. The CLICK PLUS personal computer to any C-more Micro- PLUS C2-03CPU. Sold in packs of 2.
PLC Hardware User Manual can be Graphic panel, CLICK PLC, or select CLICK
downloaded free at the AutomationDirect PLUS PLC for setup and programming.
Web site; www.AutomationDirect.com Note: This cable assembly uses the PC’s USB port and
converts the signals to serial transmissions. The USB port
supplies 5VDC to the Micro-Graphic panel for configuration
operations. C0-4TB $10.00
Assembly includes standard USB A-type Spare 24VDC Power Terminal Block
connector to B-type connector cable, Replacement terminal block for the
custom converter, and an RS232C cable 24VDC supply power to the PLC. Sold in
with an RJ12 modular connector on packs of 2.
each end.

C0-USER-M $0.00
CLICK PLC Hardware User Manual
Manual covers all CLICK PLC and C0-8TB $16.50
I/O module installation and wiring, Spare 8-Point I/O
specifications, error codes and Terminal Block
troubleshooting guide. The CLICK
PLC Hardware User Manual can be Replacement terminal
downloaded free at the AutomationDirect block for the 8-point
Web site; www.AutomationDirect.com USB-CBL-AMICB6 $5.25 I/O modules. Sold in
USB A to USB microB Programming packs of 2.
Cable Assembly (CLICK PLUS Only)
Programming cable, USB A to USB
microB, 6ft (1.83 m) length. For use with
C0-8TB-1 $19.50
CLICK PLUS PLCs and most USB devices.
Spare 13-Point I/O Terminal Block
The USB port supplies 5VDC to the CLICK
PLUS CPU for programming. Replacement terminal block for the 8-point
I/O relay modules. Sold in packs of 2.

C0-PGMSW $12.00
Programming Software USB
The programming software can be
downloaded free at the AutomationDirect D2-DSCBL $35.00
Web site, or the USB can be purchased Programming Cable for CLICK/CLICK
from the AutomationDirect online Web PLUS and DirectLOGIC PLCs C0-16TB $23.00
store. www.AutomationDirect.com Spare 16-Point I/O
12ft. (3.66 m) RS232 shielded PC
Terminal Block
programming cable for CLICK, select
CLICK PLUS PLCs, DL05, DL06, DL105, Replacement terminal
DL205, D3-350, D4-450, D4-454, and block for the 16-point I/O
Do-more H2 and T1H series CPUs. 9-pin modules and PLC built-in
D-shell female connector to an RJ12 6P6C I/O. Sold in packs of 2.
connector.

C2-6TB $16.50
Spare 6-pt Terminal Block
Replacement terminal
Note: If your PC has a USB port but does not have a serial port, block for the C2-DCM
you must use programming cable EA-MG-PGM-CBL to connect serial ports.
to CLICK PLCs. For CLICK PLUS PLCs, you may also use Sold in packs of 2.
USB-CBL-AMICB6

www.automationdirect.com CLICK PLCs tCLP-167

 For the latest prices, please check AutomationDirect.com.
1-800-633-0405

Accessories
SE-ANT250 $37.00 C2-FILL $8.50 MSD-SLC16G $100.00
Wi-Fi/Bluetooth Dome Antenna CPU Option Slot Cover 16GB microSD card, industrial grade,
3D NAND Flash (with SLC Mode),
2.4 GHz antenna, IP67, panel mount, Snap-on cover
85°C [185°F] max operating temp.
9.8 ft (3m) cable length, for external for CLICK PLUS
mounting when CLICK PLUS PLC is CPU Option Slot
installed in a metallic enclosure. in applications
without an
Option Slot
module present.

SE-ANT210 $10.50 D2-BAT-1 $6.50 TW-SD-MSL-2 $4.00

Wi-Fi/Bluetooth Whip Antenna Replacement CR2354 battery for Insulated Slotted Screwdriver
Standard, Analog, Ethernet Standard and 0.4 x 2.5 x 80 mm slotted screwdriver for
Whip/straight 2.4
Ethernet Analog PLC units. terminal blocks.
GHz antenna, IP65,
connector mount.
Not recommended
for installation in a
metallic enclosure.

DN-EB35MN $31.50 D0-MC-BAT $3.00 DN-WS $72.00

DINnector End Bracket Replacement CR2032 battery for Wire Stripper
CLICK PLUS PLC units.

C-more and C-more Micro ZIPLink Wiring Systems Ethernet Cables

Graphic Operator Interfaces Pre-terminated Cat5e Ethernet patch
cables with RJ45 connectors provide
dependable communication in industrial
applications. These cables are available in
various lengths and support transmission
speeds of 10/100/1000 Mbps.

www.automationdirect.com CLICK PLCs tCLP-168