Bur3003

Barcode Scanner

User Manual

Service Mailbox
[email protected]
[email protected]

V51.11B
Contents

Technical Parameter 3
Packing list 4
Battery & Charging 4
Set Up Step 5
FAQs 6
Troubleshooting 8
Optional Function settings 9
1. Pairing Mode Setting 9

2. Upload Mode Setting 12

3. Scanning Mode Setting 15

4. Duplicated Barcode Detection 15

5. Beep Setting 16

6. Interface Setting 17

7. Identity Barcode Type 18

8. Keyboard Language Setting 19

9. Case Sensitivity Setting 21

10. Battery Remaining 21

11. Power Off Settings 22

12. End Character Setting 22

13. Barcode Types Able/Disable 23

14. Insert and Delete Character 27

15. ASCII Table 34

1
In order to correctly use the bar code scanner, please read the instruction carefully and
do not arbitrarily scan the settings code otherwise some settings may not be available
temporarily.

Please keep this instruction for reference in the future.

If you have any question or concern about the operation of the scanner, please contact
us at following Email:

[email protected]
[email protected]

You are suggested to write down the model & the specific scenario and consult the
maintenance person should you find the scanner abnormal.

2
Technical Parameter

Mfr P/N Bur3003 Serial

Radio Frequency 436.3MHz Wireless
Wireless Range Indoor 100m, outdoor 400m
Memory 100000 barcodes
Battery capacity 2600mAh
Charging power DC 5V 400mA
Standby current 18uA-5mA
Working current 15-40mA
Printing Contract >25%
Light source 650nm LED
LED life 12000 hours
Button life 8000,000 times
Resolution 3.3 mil
Scanning width 30cm
CPU ARM 32-bit Cortex
Bit Error rate 1/20million
Printing Contract >25%
Decoding speed 260 times/sec
Scanning angle rotor angel±30°，inclination± 45°，declination ± 60°

Drop test 2.0m

Certificate CE，FCC，RoHS ，IP54

UPC/EAN, UPC/EAN with complementary, Code39,

Code39 Full ASCll,

Applicable 1D barcode
Codabar, industrial/Interleaved 2of 5, Code93, MSI,

Code11, ISBN, ISSN,China post

3
Packing list
•Barcode scanner*1
•USB Cable*1
•Instruction Manual*1
•USB Wireless receiver *1

Battery & Charging

The scanner is powered by 2600mAh chargeable battery.
Please ensure that the scanner has enough power before use.

Low battery level indication

The red indicator light flashes three time, it indicates that the power is less than 30%.
Please charge the scanner as soon as possible.

The red light flashes three times and then cut down automatically, it indicates that the
power is less than 20%. The scanner cannot be powered as it enter into low voltage
cutoff mode. please stop scanning and charge the scanner.

Charging indicator：
The red indicator light on the top of the scanner will flash all the time during charging,
and it will go off when the scanner is fully charged.

NOTE:
1. Please use computer USB interface or special 5V DC power adapter for charging, the
abnormal power will cause permanent damage to scanner and battery

2. The USB cable is not only used for charging, but also used for receiving the barcode.
The barcode scanner will automaticlly switch to USB Wired Mode, once the USB cable is
inserted into the USB slot of the computer.
In USB Wired Mode, user can scan barcode while charging.

4
Wireless Mode Set Up Step
The scanner has been paired with the receiver, and set up already.

Step 1, Power on the scanner by pressing the button. The buzzer has a triple beeps, the
blue light on the top of scanner will be on.

Step 2. Insert the USB receiver into the USB port of computer. The USB receiver’s blue
light will be on.

Step 3. Open notepad on computer and move cursor to the blank where scanning
output should be placed. Scanning results can be displayed on computer then.

If the barcode does not displayed， please set up the scanner again according to the
following steps.

Step 1. Unplug the USB receiver and plug it in again

Step 2. Within 30 seconds, scan these codes in order.

Restore default

Match

Instant upload mode

USB_HID

Step 3. Open Word on computer, move cursor to the blank, scan a barcode to see if it
can be uploaded.

5
FAQs:

Q1. If i scan a product barcode, will it include the name of the product in the file
automatically?

Answer：
The scanner works like a keyboard. The scanner does not interpret what the barcode is,
it just "types" out a string of alphabet numeric characters that the barcode represents.

it's up to the database software you are using to interpret what that string of characters
means. Once you acquire the barcodes, you have to correlate them to something more
meaningful by either purchasing a software service that will interpret the barcode and
relate it to a product, or you can use your own internal inventory system to assign the
barcodes to specific products.

After creating the relationship between your barcode and the corresponded
information, when you enter the barcode into the software by the scanner,your
software will look up the barcode and then output the related information of your
product.

Q2. Why does scanner not read the barcode exactly. When I use the scanner to
read a barcode of an item, I get a different result from the barcode itself.

Example 1.There are two separate barcodes together. It scanned the first 12 digits in
the barcode but not the last five.

Solution： Please scan the code”UPC/EAN extra code-ON”on page 24.

Example 2. The original UPCE barcoe is “01234565”, but the program ask for filling
in 12 digits on the cell.
Solution: Please scan the setting code “UPCE to UPCA-On”on page 24.

Example 3.The original barcode is “ abc12345 ” ， the scanning result is

“+A+B+C+D12348”，the scanner put “+” between character.

Solution：Please scan the code “Code 39 FULL ASCII-On”on page 25.

6
If that is not your case, please send us a clear picture of the barcode and the result you
get, our customer service will help you to solve the problem.

Q3. Some barcodes can not be read, why?

Answer：
A. Incomplete and unclear barcodes might not be read.
B. It is possible that the setting is off by default for some barcode types which are not
commonly used. You need to activate a specific barcode type to get it working.

Please feel free to contact our Customer Service Team for further assistance if you
don't know the exact type of barcode that you are referring to.

Q4.Is there any barcodes to remove auto-enter after every scanning?

Answer:
To remove the auto-enter, please read the code”Disable suffix”on page 22.

Q5. How to add Tab?

Answer:
To add Tab, please read the code”Add tab”on page 22.

Q6. Can the scanner send two enter after every scanning?

Answer:
To add two enter, please read these codes in order. (on page 27-37 ).

“Insert character” (on page 27 )

“All barcode type” (on page 27 )
“Data group 1” (on page 28 )
“After barcode” (on page 30 )
“013 CR/ENTER” (on page 34 )
“013 CR/ENTER” (on page 34)
“Save settings” (on page 31 )

7
Troubleshooting
Problem Possible Reason Solution

Insert the USB receiver 1. The PC’s USB port is out Connect the USB receiver
into the PC‘s USB port, of condition. to another USB port.
the receiver’s light does Contact
not light up or the blue 2. The USB receiver is out
[email protected]
light is flashing. of condition.
for the replacement.
Power on the scanner,
the scanner has no
reaction. the buzzer does
Connect the scanner to
not beep, the blue light
The battery run out. PC’s USB port for charging
on the top of scanner
via USB cable
does not turn on, the red
scanning laser does not
show up.
Connect the scanner to
The PC’s USB port is out
another USB port for
of condition.
The scanner can not hold charging.
the charge. Contact
The USB cable is out of
[email protected]
condition.
for the replacement.
Power on the scanner,
the buzzer beeps, the
blue light on the top of Contact
The laser head is out of
scanner will be on, the [email protected]
condition.
red scanning laser does for the replacement.
not show up or become a
dot.

The scanner failed to

Unplug the receiver and
match the USB receiver.
plug it in to PC’s USB
Scanner and USB receiver The scanner was set to port， and scan the
are all in good condition. storage mode，scanned following codes:
But the barcode can not data will be kept in the bu-
be sent to my computer. ff er of scanner. “Restore default”
“match”
The scanner was set to “instantly upload mode”
USB virtual com. “USB_HID”

8
Optional Function settings
Settings of the barcode scanner can be changed by scanning the setup barcodes
included in this manual.

1. Pairing Mode Setting

1.1 One scanner to one USB receiver：One scanner only transmits barcode to one USB
receiver.

Pairing operation:
Plug the USB receiver into your computer ,scan the code "match " to pair the scanner
with the USB receiver.

Match

Pairing indication:
（1）If the pairing succeeds, the buzzer will beep "DI-en""di di di"
（2）If the pairing fails, the buzzer will beep "DI---en"

NOTE：30 seconds after the USB receiver is inserted, the scanner cannot match the USB
receiver. If the pairing fails, please unplug the USB receiver and plug it again, then
scan the code "match".

9
Several units can work independently with different computers in the same area. They
won't interface with each other during work.

If you want to use them on multiple computers, each with own scanner and receiver.
Please set up barcode scanners follow below steps.

（1）Plug the USB receiver A into PC’s USB port

（2）Scan the code “match”using scanner A to pair the scanner A with the receiver A.
（3）30seconds after the USB receiver A is plugged (or unplug the receiver A), plug the
USB receiver B into another PC’s USB port
（4）Scan the code “match”using scanner B to pair the scanner B with the receiver B.
......

Match

10
1.2. Max.32 Scanner - to - One USB receiver
Multiple scanners transmit barcode to one USB receiver. One USB receiver can
connect to 32 scanners at most.

Pairing operation:
（1）Plug the USB receiver A into PC‘s USB port
（2）Scan the code “match”using scanner A to pair the scanner A with the receiver A
（3）Unplug the USB receiver A and plug it to PC‘s USB port again
（4）Scan the code “match”using scanner B to pair the scanner B with the receiver A
...

Match

11
2. Upload Mode Setting

2.1. Instant Upload Mode ： Read barcodes and upload it straight to the file you have
opened.

** To set the scanner to upload barcode instantly, scan the following code:

Instant upload mode

Scanning indication:
(1) The blue led 3 flashes once and the buzzer emits a sound like "DI" when the barcode
is uploaded successfully.
(2)The blue led 3 flashes once and the buzzer emits a sound like a slow "DI---en" when
the barcode can not be uploaded.

Note 1：
The transmission speed between every character can be changed by scanning the
following code. If some characters are missing, please set the scanner to lower
transmission speed. The higher the value, the slower the speed is.
Please make sure that the USB receiver is plugged.

Speed 40 Speed 50

Speed 00 * Speed 05

Speed 60

Speed 10 Speed 15

Speed 20 Speed 30

12
2.2. Storage Mode： Read barcodes and store the barcodes in scanner’s own memory.
You can upload the data to computer in batches when you need them. Internal storage
saves up to 100,000 barcodes.

Note： In storage mode, the barcode will be stored in the scanner and will not come up
on your computer instantly. The barcode comes up on your computer only when you
scan the settings code "upload data"

** To convert scanner from "instant upload mode" to "storage mode", scan the
following barcode “Storage mode“.

Storage mode
** Put the cursor in the blank, and then scan code below to upload data.

Upload data

** Put the cursor in the blank and then scan the code below to show total number of
stored barcode.

Show total storage

** Scan the barcode “Zero clearing”to clear all stored barcode. (for storage mode only)

Zero clearing

Scanning indication:
(1) The blue led 3 flashes once and the buzzer emits a sound like a fast "DI-en" when
the barcode is saved successfully in the built-in memory of the scanner
(2)The red led 2 flashes once and the buzzer emits a sound like a slow "DI---en" when

13
the barcode can not be saved in the built-in memory of the scanner. The space of
memory is not enough and cannot store any more barcodes. Please upload the saved
barcode by scanning the code "Upload Data" and then clear the saved barcode by
scanning code "zero clearing".

Note 1:
In storage mode, the transmission speed between every barcode can be changed by
scanining the following code. The higher the value, the slower the speed is.

Note 2:
If the character upload speed（on page 12-13） is set to a slower speed，and the
barcode upload speed is set to a higher speed. When uploading data in storage mode,
the data maybe be lost. If some character or barcode are missing, please set the
scanner to lower barcode transmission speed.
Please make sure that the USB receiver is plugged.

Speed 000 Speed 005

Speed 010 * Speed 040

Speed 050 Speed 060

3. Scanning Mode Setting

3.1. Manual Trigger mode (default) :

User Press the trigger, the scanner will emit a red laser to read the barcode. When user
release the trigger, the red laser will go off.

** Scan the following codes to set the scanner to Manual trigger mode .

14
 Manual trigger mode (default)

3.2. Continuous Scanning Mode

There’s no need to click the trigger in this mode. The red laser of the scanner will be on
all the time.

** Scan the following codes to set the scanner to Continuous Scanning Mode.

Continuous Scanning Mode

4. Duplicate Barcode Detection

**If you scan the setup barcode” Same Barcode Detection-permanent “ the scanner
can not upload the barcode it has read before unless scan different barcode and then
go back ,or turn off the scanner and then turn it on.

**If you want the scanner able to read the same barcode at a certain time interval, you
can choose an interval of 1 second, 2 seconds ... or a longer period of time, up to 25
seconds.

For example, “ Same Barcode Detection-2 seconds “, scanner will read the same
barcode again after every 2 second. The calculation of time starts from scanning the
bar code, regardless of whether the bar code is scanned successfully or not, it is
calculated from the last scan.

** Scan “ Same Barcode Detection-Off “ to turn off this function.

Same Barcode Detection-permanent Same Barcode Detection-1 second

15
Same Barcode Detection-2 seconds Same Barcode Detection-3 seconds

Same Barcode Detection-4 seconds Same Barcode Detection-5 seconds

Same Barcode Detection-10 seconds Same Barcode Detection-15 seconds

Same Barcode Detection-25 seconds Same Barcode Detection-Off

5. Beep Setting
**Scan one of the following barcodes to adjust the size of the decoding buzzer and
startup sound.

Low volume Medium volume

High volume (default） Beep-Off

6. Interface Setting

6.1. USB-HID mode

In the HID protocol, there are 2 entities: the "host" and the "device".
The host communicates with the device and receives input data from the device on

16
actions performed by the human.
The most common example of a "host" is a PC.
The "device" is the entity that directly interacts with a human, such as a keyboard or
mouse.

** To set the scanner as a keyboard to enter the barcode , please unplug the USB
receiver and plug it in again, and then read the following code “USB_HID”

USB_HID

6.2. USB virtual COM mode

In USB virtual COM mode, the scanner needs to work with driver and serial software.

Expected final behavior is that even if you open up another page , the scanned
information will show up in the window of serial software.

The scanned barcode won’t come up on universal software like notepad, excel，word
etc.

Please contact us if you need to set it to USB virtual COM mode，we will send you the
driver and the serial software.

7. Identity Barcode Type

This setting is to identify what type of the barcode is, follow the below steps to confirm:

Situation 1: Scan the code "Add ID front-on" below, then scan your goal barcode, there

17
will be a character BEFORE the barcode you scanned, and this character states your
Barcode Type. After that, if you don't need this prefix any more, please scan the code
"Add ID front-Off (default)" to hide it.

Add ID front - ON

Scan Goal Barcode

Add ID front-Off

Barcode type ID Barcode type ID

CODE 93 h MSI/PLESSEY l

CODABAR k EAN-8 d

UPC-A b EAN-13 e

UPC-E c INTERLEAVED 2/5 i

ISBN f CODE 11 m

CODE 39 a CODE 128 g

18
8. Keyboard Language Setting

The scanner support 25 international keyboards:

You are suggested to set the keyboard type of the scanner to be in agreement with
that in real use by scanning the correspondent barcode listed below.

UNITED STATES （default） FRENCH

SERBIA/YUGOSLAVIA BELGIUM

GERMANY SLOVENIA

BRAZIL HUNGARY

SPAIN CANADIAN-FRENCH

ITALY SWEDEN

19
CROATIA LATIN AMERICA

SWITZERLAND (FRENCH) CZECHOSLOVAKIA (CZECH)

NETHERLANDS SWITZERLAND (GERMAN)

CZECHOSLOVAKIA (SLOVAK) NORWAY

UNITED KINGDOM DENMARK

UNIVERSAL
POLAND

FINLAND PORTUGAL

20
9. Case Sensitivity Setting

The scanner can change all the letter cases of barcode into uppercase or lowercase.

Letter case of barcodes can be altered through scanning correspondent bar code
below.

Note: Please deactivate caps lock on keyboard first.

All Capital All lowercase

Swap Capital/ lowercase Cancel capital/lowercase settings

10. Battery Level

To know how much electricity remains, put the cursor in the blank and then scan the
following barcode.

Battery level

21
11. Power Off Settings
The scanner will be powered off if there is no operation on it over 2 minutes. Short
press on the trigger can wake it up.

Scan one of the following barcode to set the time interval,when it's idle exceeding the
time interval you set,the scanner will be power off.

20s Automatic power off 50s Automatic power off

5mins Automatic power off 30mins Automatic power off

Power off Never power off

12. End Character Setting

By default，the scanner is sending a 'carriage return' after scanning a code (the same as
pressing the 'enter' key) .

CR/ENTER (default） CR+LF

Tab Disable suffix

eg.

To add Carriage Return, please read code “ Add Carriage Return”

To remove Carriage Return,please read code “ disable suffix ”

22
13. Barcode Types Able/Disable

The code ending with word "*" is the default settings.

UPCA:

UPCA-On* UPCA-Off

Show UPCA check digit* Hide UPCA check digit

Show UPCA Leading digit* Hide UPCA leading digit

UPCA to EAN13-On UPCA to EAN13-Off*

UPCE

UPCE-On* UPCE- Off

Show UPCE check digit* Hide UPCE check digit

Show UPCE leading digit* Hide UPCE leading digit

23
UPCE to UPCA-On UPCE to UPCA-Off*

EAN13

EAN13-On* EAN13-Off

Show EAN13 check digit* Hide EAN13 check digit

EAN13 to ISBN-On EAN13 to ISBN - Off*

EAN13 to ISSN - On EAN13 to ISSN - Off*

EAN8

EAN8 - On* EAN8-Off

Show EAN8 check digit* Hide EAN8 check digit

UPC/EAN Extra code

UPC/EAN extra code-On UPC/EAN extra code-Off*

24
Code39
CODABAR

Code39-On*
CODABAR-On* Code39-Off
CODABAR-Off

Show CODABAR
Code39 start/stop digit
FullASCII-On Hide CODABAR start/stop digit*
Code39FullSCII-Off*

Show Code39 start/stop digit Hide Code39 start/stop digit*

Code32

Code32- On Code32-Off*

Show Code32 check digit Hide Code32 check digit*

Code128

Code128-On* Code128-Off

Code93

Code93-On Code93-Off*

Code11

Code11-On Code11-Off*
25
 Industrial 2 of 5

Industrial 2 of 5 -On* Industrial 2 of 5 -Off

Interleaved 2 of 5

Interleaved 2 of 5 -On* Interleaved 2 of 5 -Off

MSI

MSI-On MSI-Off*

GS1-On GS1-Off*

14. Insert and delete character

The barcode scanners permit special characters to be added at the beginning (prefix)
or end (suffix) of the scanned barcode. The character also can be deleted.

First step： Scan one of the following setup code to choose the event.

26
 Insert character Delete character

Second step：Scan one of the following setup code to choose the barcode type.

All barcode type UPCE

UPCA EAN8

EAN13 ISBN/ISSN

Code39 Code128

Code93 Codabar

Interleaved 2 of 5 Industrial 2 of 5

MSI Code11

27
 China post GS1D

GS1L GS1E

Code32

Note：if you do not choose the barcode type, the setting will take effect for all barcode
type by default.

Third step : Scan one of the following setup code to choose the data group.

Group 1 Group 2

Group 3 Group 4

Group 5 Group 6

Group 7 Group 8

28
Note 1： if you do not choose the data group, the scanner will take “Data group 1” as
default setting.

Note 2:
The data group is used to distinguish between different setting events.
it work on the following circumstances:

1). Differentiating the setting for different barcode types

2). Differentiating the setting for different position

Different events can take effect at the same time.

Example 1 :
If you want to put “A” before the Code39 type barcode, put "B" before the Code128
type barcode .
The setting steps is ：
Insert character> Code39>Data group 1 > Before barcode> 065 A> Saving settings
Insert character> Code128>Data group 2 > Before barcode> 066 B> Saving settings

After that,
when the scanner read a Code39 barcode, it will add “ A” before the barcode. When
it read a Code128 barcode, it will add “B” before the barcode.
when it read other type barcode ,like UPC, it will not add any character.

Example 2:
If you want to insert tabs in the third, sixth and Eighth digits of the barcode
The setting steps is ：
Insert character > All barcode type > Data group 1 > 003 ETX > 009 Tab > Saving
settings
Insert character> All barcode type > Data group 2 > 006 ACK > 009 Tab> Saving
settings
Insert character> All barcode type > Data group 3 > 008 Back Space > 009 Tab>
Saving settings

29
Fourth steps ： Scan one of the following setup code to choose the position

Before barcode After barcode

Fifth steps ：Choose the character you want to add or the digit you want to delete.

Character table please refer to ASCIl code table on page 34.

Note 1：
Ten characters can be added or deleted at most.

Note 2：
For the character deleting event, below is the corresponding deleting characters table.

001 SOH One character

002 STX Two characters

003 ETX Three characters

004 EOT Four characters

005 ENQ Five characters

006 ACK Six characters

007 BEL Seven characters

008 Back Space Eight characters

009 HT/TAB Nine characters

30
 010 LF Ten characters

Sixth steps： Scan the below code to save the setting

Save setting

To remove the insert setting，scan the following code in order

Insert character Clear setting

To remove the insert setting，scan the following code in order

Delete character Clear setting

31
32
33
34
35
36
37
FCC Caution.
a、§ 15.19 Labeling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

b、§ 15.21 Changes or modification warning.

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

c、§ 15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

38
-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

39