Scribd
Upload
3 views5 pages

AutoWatering Ino

The document is an Arduino sketch that integrates a BME280 sensor for measuring temperature, humidity, and pressure, along with an ultrasonic sensor for water level detection and a moisture sensor for soil humidity. It also controls an LED and a relay for watering plants, and provides feedback through an OLED display and sound. The program operates in a loop, checking sensor values and managing watering based on moisture levels and water distance every minute.

Uploaded by

midhansh100
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
3 views5 pages

AutoWatering Ino

The document is an Arduino sketch that integrates a BME280 sensor for measuring temperature, humidity, and pressure, along with an ultrasonic sensor for water level detection and a moisture sensor for soil humidity. It also controls an LED and a relay for watering plants, and provides feedback through an OLED display and sound. The program operates in a loop, checking sensor values and managing watering based on moisture levels and water distance every minute.

Uploaded by

midhansh100
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 5

#include <Wire.

h>
//BME280
#include <Adafruit_BME280.h>
//OLED
#include
<I2CLiquidCrystal.h>

//------------------------------

//BME280
#define
I2C_SCL 5
#define I2C_SDA 4
Adafruit_BME280 bme;

//OLED
#define
I2C_ADDR 0x3c
#define BRIGHT 127
I2CLiquidCrystal oled(I2C_ADDR, (uint8_t)BRIGHT);

//Music
#define
BEAT 300
#define PIN 10

#define DO 262
#define RE 294
#define MI
330
#define FA 349
#define SO 392
#define RA 440
#define SI 494
#define
HDO 523

//----------------------

//Timer
int counter = 0;

//Ultrasonic
Sensor
int Trig = 8;
int Echo = 9;
int Duration;
float Distance;

//LED
int
led = 7;

//misture sensor
int water_count = 0;

//relay
int relay
= 13;
void setup() {
//BME280
Serial.begin(9600);
Wire.begin();

if (!bme.begin(0x76)) {
Serial.println("Could not find a valid BME280
sensor, check wiring!");
while (1);
}
delay(100);

//OLED

oled.begin(16, 2);
oled.display();
oled.clear();
oled.noBlink();

oled.noCursor();
oled.home();
oled.print("Wait a minutes.");

//Ultrasonic Sensor
pinMode(Trig,OUTPUT);
pinMode(Echo,INPUT);

//LED
pinMode(led,OUTPUT);

//relay
pinMode(relay, OUTPUT);
}

void
loop() {

//Check temperature, humidity, and soil humidity once a minute.

if(counter == 1){
ckeckBME280();
checkWater();
checkMoisture();

delay(10000);//10sec
counter++;

if(counter >= 6){

counter = 0;
}

checkWater();
}
//BME280
void ckeckBME280(){

// Get data from BME280 sensor


float t = bme.readTemperature(); //
C
float h = bme.readHumidity(); // %
float p = bme.readPressure()
/ 100.0F; // hPa
Serial.print("Temperature:");
Serial.println(t);

Serial.print("Humidity:");
Serial.println(h);
Serial.print("Pressure:");

Serial.println(p);
Serial.println();

oled.setCursor(0, 0);
oled.print(String(t)+"C
");
oled.print(String(h)+"% ");
}

//Ultrasonic Sensor
void
checkWater(){
//Check the water level in the bucket.
digitalWrite(Trig,LOW);

delayMicroseconds(1);
digitalWrite(Trig,HIGH);
delayMicroseconds(11);

digitalWrite(Trig,LOW);
Duration = pulseIn(Echo,HIGH);

if (Duration>0)
{
Distance = Duration/2;
Distance = Distance*340*100/1000000; // ultrasonic
speed is 340m/s = 34000cm/s = 0.034cm/us
Serial.print(Distance);
Serial.println("
cm");

if(Distance > 12){


digitalWrite(led, HIGH);
}else{

digitalWrite(led, LOW);
}

}
}

//moisture sensor
void
checkMoisture(){
//Measure soil humidity
int moisture = analogRead(A0);

Serial.print("Moisture Sensor Value:");


Serial.println(moisture);
oled.setCursor(0,
1);
oled.print("Moisture: " + String(moisture) + " ");

if(moisture
<= 300){
water_count++;
if(water_count == 5){//To wait for the water
to go through the pot.
watering();
water_count = 0;
}

}
}

//Watering
void watering(){
digitalWrite(relay, HIGH);

delay(2000);
digitalWrite(relay, LOW);
delay(8000);
completeWatering();

counter++;
}

//Music
void completeWatering(){
//Let them know
that watering is complete.
oled.setCursor(0, 0);
oled.print(" Thank
you! ");
oled.setCursor(0, 1);
oled.print(" (^ O ^)/ ");

tone(PIN,DO,BEAT) ; // C
delay(BEAT) ;
tone(PIN,RE,BEAT)
; // D
delay(BEAT) ;
tone(PIN,MI,1200) ; // E
delay(BEAT)
;
delay(BEAT) ;
delay(BEAT) ;
tone(PIN,RE,BEAT) ; //
D
delay(BEAT) ;
tone(PIN,DO,BEAT) ; // C
delay(BEAT)
;
delay(BEAT) ;
tone(PIN,DO,BEAT) ; // C
delay(BEAT)
;
tone(PIN,RE,BEAT) ; // D
delay(BEAT) ;
tone(PIN,MI,BEAT)
; // E
delay(BEAT) ;
tone(PIN,RE,BEAT) ; // D
delay(BEAT)
;
tone(PIN,DO,BEAT) ; // C
delay(BEAT) ;
tone(PIN,RE,1200)
; // D
delay(BEAT) ;
delay(BEAT) ;
delay(4400);

counter++;
oled.setCursor(0, 0);
oled.print(" ");

oled.setCursor(0, 1);
oled.print(" ");
ckeckBME280();

int moisture = analogRead(A0);


oled.setCursor(0, 1);
oled.print("Moisture:
" + String(moisture) + " ");
}

You might also like