GENERAL PHYSICS

1.1 INTRODUCTION
PHYSICS can be defined as the study of the physical properties of matter and the concepts of energy

MATTER refers to any material that can occupy some space and can be measured, weighed or examined by experimental
testing.
1.2 MEASUREMENT
1.2.1 Physical quantities
Any measurable physical feature or property of an object is called its PHYSICAL QUANTITY, e.g.
temperature of a body, an area of a field, speed of a car, etc.
In Physics length, mass and time are known as Basic or Fundamental physical quantities.
Many other physical quantities (e.g. force, speed, velocity, voltage, etc) are related to these fundamental
physical quantities, therefore they are known as DERIVED PHYSICAL QUANTITIES. (the units can be
derived from those of fundamental quantities and hence are called derived units) e.g.
SI unit of speed
Force
= m/s (read as metre per second)
1.2.2 INTERNATIONAL SYSTEM OF UNITS (Systĕme International d’Unitĕs- SI UNITS)
This is an internationally agreed system of units used to measure physical quantities. (Originally known as MKS
system; M- metre, K- kilogram and S- second). Each quantity has its own SI unit.

FUNDAMENTAL PHYSICAL QUANTITIES AND THEIR SI UNITS

QUANTITY S.I. UNIT SYMBOL FOR UNIT Other UNITS

Kilometre, centimetre,
Length Metre m Millimetre,Lightyear
Grams,milligrams,
Mass Kilogram kg Tone
Hours, minutes, days,
Time Second s Weeks,years
Milliamps, microamps,
Electric current Ampere A
Degree Celsius
Temperature Kelvin K
-
Amount of substance Mole mol
-
Luminous Intensity Candella Cd

SOME DERIVED QUANTITIES AND THEIR SI UNITS

Quantity symbol SI unit Symbol
area A square metre m2
acceleration a metre per second squared m/s2, m s-2
energy E joule J
force F newton N
density D, ρ kilogram per cubic metre kg/m3
power P watt W
velocity u, v metre per second m/s, m s-1
pressure P pascal Pa
frequency f hertz Hz
period T second S

Page 1
1.2.3 Submultiples and multiples of a base unit
These are bigger or smaller units obtained by putting certain prefixes (with scientific meanings) in front of a
base unit.
Examples MULTIPLES
SUBMULTIPLES kilometre (km), gigawatt (GW), megahertz (MHz), etc.
Centimetre (cm), decisecond (ds), microvolt(μV), etc.
PREFEXES USED IN SUBMULTIPLES AND MULTIPLES
Prefix symbol Meaning value Conversion factor
nano- n One thousand millionth 0.000 000 001 10-9
micro- μ One millionth 0.000 001 10-6
milli- m One thousandth 0.001 10-3
centi- c One hundredth 0.01 10-2
deci- d One tenth 0.1 10-1

kilo- k One thousand 1000 103

mega- M One million 1 000 000 106
giga- G One thousand million 1 000 000 000 1012

1.2.4 CONVERSION OF UNITS:

Rule 1: When you convert from a larger to smaller unit, you multiply (by an appropriate conversion factor) ; e.g.
km -------> m; multiply by 1000.
Rule 2: When you convert from a smaller to larger unit, you divide (by an appropriate conversion factor); e.g.
seconds ----------> hours; divide by 3600

]]

Page 2
 1.2.6 TIME
Time can be defined as is the interval between two events.
SI unit: second (s)
Other units: microsecond (μs), millisecond (ms), decisecond (ds), minute (min), hour (h), day, year, etc.
time name symbol
24 hours (86 400s) day d
60 minutes (3600 s) hour h
60 seconds minute min
10-3 seconds millisecond ms

Time can be measured with stopwatches or clocks. The electronic stopwatch can measure time precisely up to 1/100 of a
second (0.01 s)

Time = 1 min + 48 s + 5/100 s time = 0 min + 15 s

= 1 min 48.05 s = 15.00 s

THE SIMPLE PENDULUM

A pendulum is a piece of a thread which is fixed at one end and tied to a metal ball (called a bob) on the other end. The bob
of a pendulum is free to swing from one side to another.

The amplitude (a) of a pendulum is the angle between the rest position and position of maximum displacement.
The length (l) of pendulum is measured from the fixed position to the centre of the bob.
The period (T) of the pendulum is the time taken by the bob to complete one swing or oscillation, i.e. the time taken by the
bob to move from point A to C and back to A in the diagram below. Period is measured in seconds (s)
Period = total time taken/number complete swings (oscillations)

Frequency (f) is the number of completed oscillations generated in 1 second. The SI unit is hertz (Hz)
frequency = number of swings/total time taken
Therefore;
f = 1/T or T = 1/f
then 1 Hz = 1/s
EXPERIMENT:- To determine the period (T) of a simple pendulum
Procedure
• Set up a pendulum as shown in the diagram above with l = 100. cm.
• Pull the bob slightly to one and then release it and then let the pendulum make few oscillations until they are
periodic and start the stopwatch.
• Using the stopwatch, find the time t1 for 20 oscillations. Find time t2 for another 20 oscillations.
• Find the average time <t> for 20 oscillations using the equation <t> = (t1 + t2)/2.
• Calculate the period of the pendulum using the formula T = <t>/20.

Page 3
 • Repeat the experiment for different values of l; l = 90.0 cm, l = 80.0 cm, l = 70..0cm, l = 60. and l = 50.0 cm.,
40.0 cm, 30.0 cm
• Record the observations appropriately in a table
• Plot a graph of T2 against l

Table of Results
Length l/cm Time for 20 Average time <t>/s Period T/s T2/s2
oscillations t
t1/s t2/s
100.0
90.0
80.0
70.0 32.26 32.06 32.17 1.61
60.0

60.0 29.37 29.69 29.53 1.48 2.2

50.0 26.78 26.82 26.80 1.34 1.8
40.0 24.93 23.29 24.11 1.21 1.5
30.0 24.12 22.15 23.14 1.16 1.3

Plot a graph of T2 against L

T2/s2

Length/cm

From the experiment we found that

• The period of pendulum is affected by the length of the pendulum. (NB:- The size of the bob and amplitude of the
pendulum [for small angles] do not affect the period).
• The graph is a straight line which means T2 is directly
L/cmproportional to l, this means if LENGTH is doubled, T
quadruples.

SOURCES OF ERROR IN TIME MEASUREMENT

• Human reaction time- a time lag between seeing an event and starting the watch. For people the lag is normally
0.2 s.
• The watch/clock may move faster or slower that the normal time/rate. This introduces a systematic error in every
reading taken using that watch.
• Instrumental error /zero error – failure to re-set the watch to zero before starting to time the event.
1.2.7 ACCURACY OF A MEASURING INSTRUMENT
A more accurate instrument measures any quantity with least approximation. The accuracy of any given instrument is
represented numerically by the value of smallest unit an instrument can measure without approximation. This is usually
given by the value of the smallest division in any scale.

Examples • lab thermometer is 1° C.

The accuracy of a:-
• metre rule is 0.1 cm (0.01 mm)
• vernier calliper is 0.01 cm (0.1 mm)
• micrometer is 0.01 mm (0.001 cm)
• stopwatch is 0.01 s
• clock is 1 s

Page 4
 Accurancy = 1- 0/10 = 0.1 A

1.3 QUESTIONS

1. Complete the table below to show what property is measured by the instrument or what the instrument can be
used to measure the property stated. State the correct unit in each case.

instrument Property measured Unit

Micrometer
Stopwatch
length centimetre

2. What are lengths of the objects in the diagrams below?

3. What are the readings shown by the micrometers below?

(a) (b)

4. What is time shown by the each of the stopwatches below?

(a) (b)

Page 5
5. (a) The diagram below shows a simple pendulum.

The bob of the pendulum was pulled to position A and then was released. The period of the pendulum was
found to be 0.64 s.

(i) Describe, in terms of positions A, B or C, what is meant by one complete swing.

(ii) How long did it take the pendulum bob to swing from A to B?
(iii) Explain briefly how the period could be accurately measured.

(b)
A student performs an experiment to determine the
period of a simple pendulum. She uses a stopwatch to (i) What is the time recorded by the stopwatch?
record the time taken to produce 20 oscillations. The (ii) Calculate the period of the pendulum.
diagram below shows the face of the stopwatch (iii) State two factors that affect the period of the
used. pendulum.

6. A piece of metal pipe is 3 m long, and its internal and external diameters are 20.0 mm and 24.0 mm respectively.
Describe how you would obtain experimentally accurate values of these (i) the internal and (ii)
external diameters of the pipe.

7. Fig
. 7.1 shows the face of an ammeter. The ammeter reads
0.2 A with no current passing through. c. Fig. 7.2 shows the same ammeter with current
passing through.

Fig. 7.1
(a) What is the value of the accuracy of the ammeter?
(b) What error does the ammeter show? Fig. 7.2

Page 6
 (d) 2 litres or 300 cm3?
(i) What is the reading shown?
(ii) What is the correct value of the current passing
through the ammeter?

8. In each of the following pairs, which quantity is larger?

(a) 2 km or 2500 m?
(b) 2 m or 1500 mm?
(c) 2 tonnes or 3000 kg?

2.0 MOTION
INTRODUCTION ; TWO BRANCHES IN THE STUDY OF MOTION

❖ KINEMATICS . The study of moving objects without reference to mass of the moving object nor reference to forces
that cause the motion.
❖ Dynamics: The study of moving objects under the influence of Forces.

*Scalar quantity:- quantity with magnitude only, e.g. mass, distance, temperature, speed, etc.
Vector quantity:- quantity with both magnitude and direction, e.g. velocity, acceleration, force, displacement, etc

2.1.1 DISTANCE AND DISPLACEMENT

DISTANCE (S) DISPLACEMENT(S)

Length covered by an object measured along the path of distance travelled in a specified direction
motion. e.g A 6.4 cm B A B 6.4 cm East
SI unit of distance and displacement : metre (m) SI unit of distance and displacement : metre (m)
Distance is a scalar as it has only the size a vector as it has both the size and direction.

Illustration:- A boy starts from point A and walks 3 km northwards to point B and then turns eastwards and walks 4 km to
point C. Find a) his total distance travelled b) and displacement during the journey.

a) total distance travelled ABC = 2 km + 2 km = 4 km

b) total displacement S; AC2 = AB2 + BC2
Page 7
 = 32 + 42
AC = 5 km, 54° east of north
c) The boy continues with the journey and walks back to point A. Calculate the total distance travelled and
displacement for the whole journey.
c. i) total distance travelled ACA’ = 3 km + 4 km + 5 km = 12 km
ii) total displacement AA’ = 0 km

2.1.2 SPEED AND VELOCITY

SPEED ( u,v) VELOCITY ( u,v)
Definition : Distance travelled per unit time The rate of change in displacement
Speed= distance/time Velocity =change in displacement/time
Scalar quantity Vector quantity, Speed +direction =velocity
East : Positive + 5m/s
West : negative -5m/s
S.i unit is metres per second S .i unit is metres per second
Other units: cm/s, km/h, m/min, etc. Other units: cm/s, km/h, m/min, etc.+ direction or with
a negative
Conversions between m/s and km/h Conversions between m/s and km/h

3600/1000 3600/1000
--------------------------------> -------------------------------->
m/s km/h m/s km/h
<-------------------------------- <---------------------------------

Average velocity , v = total displacement /Total time

Average speed v = total distance/Total time

2.1.3 ACCELERATION (a )
It is the rate of change of velocity Acceleration. It is also a vector quantity. Its SI unit is metre per second squared (m/s2) or
(m s-2).
Acceleration = change in velocity/time taken
a =( final velocity – initial velocity)/total time taken
a = (v – u)/t
DECELERATION
When a body slows down its speed decreases and the acceleration becomes negative. Negative acceleration is called
DECELERATION or RETARDATION.
2.2 STATES OF MOTION
2.2.1 UNIFORM/STEADY/CONSTANT SPEED
Distance travelled in equal intervals of time is the same i.e. distance travelled every second is the same.
e.g.
time/s 0 1 2 3 4 5
distance/m 0 5 10 15 20 25
Speed/(m/s) 0 5 5 5 5 5
The body covers 5 m every second, this represents a
nconstant speed of 5 m/s.
2.2.2 NON-UNIFORM SPEED
Distance travelled per unit time varies.

i) non-uniform increasing speed

Page 8
 time/s 0 1 2 3 4
distance/m 0 5 14 30 60
Speed/(m/s) 0 5 7 10 16
The body moves a little further than the previous second every second.
ii) decreasing speed
time/s 0 1 2 3 4
distance/m 0 5 9 12 14
Speed/(m/s) 0 5 4.5 4.0 3.5

Every second the object covers a little less distance than in the previous second.
2.2.3 UNIFORM VELOCITY
Both speed and the direction don’t change i.e. the body travels with uniform speed and in the same direction (in a straight
line).
2.2.4 NON-UNIFORM VELOCITY
Either speed or direction changes (or both of them)
2.2.5 UNIFORM ACCELERATION
The rate of change of velocity with time is constant i.e. speed increases by the same amount every second and the body is
also travelling in one direction.
e.g.
time/s 0 1 2 3 4 5
speed (m/s) 0 4 8 12 16 20

Acceleration is constant and is 4 m/s2.

2.2.6 NON-UNIFORM INCREASING ACCELERATION
time/s 0 1 2 3 4 5
speed (m/s) 0 10 25 45 70 100

*Acceleration is zero for body travelling with steady speed in the same direction (uniform velocity).However, acceleration is
non-zero if the body travels with constant speed in a circular path.

-Even though the speed is constant (e.g. 5 m/s), the direction changes now and then. Therefore the velocity is non-uniform
and hence the acceleration is not zero.
2.2.7 NON-UNIFORM ACCELERATION
a) increasing acceleration b) decreasing acceleration
time/s 0 1 2 3 4 time/s 0 1 2 3 4
velocity(m/s) 0 10 30 60 100 velocity (m/s) 0 20 30 35 37

2.3 QUESTIONS
1 Explain the difference between:
a) distance travelled and displacement

Page 9
 b) speed and velocity

2 Use the words in the list below to complete the paragraphs that follow. Each word may be used once, more
than once or not at all.
acceleration average displacement distance instantaneous scalar speed
vector velocity
Quantities which have magnitude but no direction are called ................................ quantities. Speed is a
........................... quantity. Velocity is a ............................ quantity.
If an object moves in unspecified direction, it has moved through a certain ............................................. If
the direction is specified, it has undergone a ....................................................
The rate of change of ......................... of an object is called its acceleration. Acceleration is a ......................
quantity. The formula: (final speed – initial speed) / time gives the ..................................... of an object.

3 a) A millipede moves a distance of 3.0 m in 1.5 s. What is its average speed?

b) A car travels 600 m in 30 s. What is its average speed?
4 A car has a steady speed of 8m/s.
a) How far does the car travel in the 8 s?
b) How long does the car take to travel 160 m?
5 a) A cyclist, rides 2 km east then 2 km north. The trip takes two hours in all.
Find : i) the average speed and ii) the average velocity.

b) A racing car completes a 5 km lap in 100 s. After this lap what is its i) displacement ii) average
speed and iii) average velocity?
6 Express a) speed of 130 km/h and b) speed of sound in air (which is about 330 m/s) in km/h.
7 What is meant by:
a) a speed of 100 km/h
b) an acceleration of +10 m/s2
c) an acceleration of -5 m/s2
8 A car takes 8 s to increase its velocity from 10 m/s to 30 m/s. What is its acceleration?
9 A motor cycle, travelling at 20 m/s, takes 5 s to stop. What is its average retardation?
10 An aircraft on its take-off run has a steady acceleration of 3 m/s2.
a) What velocity does the aircraft gain 4 s?
b) If the aircraft passes one post on the runaway at a velocity of 20 m/s, what is its 8 s later?

2.4 MOTION GRAPHS

2.4.1 Distance-time graph
A distance-time graph shows how the distance travelled varies with time. The gradient of the graph represents the speed of
the body
a) Uniform speed

Page 10
The distance-time graph above is a straight line showing that the body is travelling with uniform speed.
The gradient of the graph; Then speed = 10 m/s
Grad = ∆s/∆t = y2 – y1 / x2 – x1
=60 - 20/ 6 - 2 b) i) Non-uniform increasing speed
= 10

In graph above the body is travelling with non uniform increasing speed since the graph is not a straight line but instead is a
curve. The gradient of the graph varies. The speed at any particular time is found by calculating the gradient of the tangent
to the curve at that time

ii) Non- uniform decreasing speed

2.4.2 Velocity-time graph and Speed-time graphs

The speed- time graph shows how speed varies with time.
Note; 1) the gradient of the speed- time represents the acceleration of the body
2). The area under the graph is equal to the distance travelled by the body.
a). Speed-time graph with
Uniform acceleration

In the speed- time graph above the body is moving with a uniform acceleration since the graph is a straight line.
Acceleration = grad = ∆Y/∆X
b). Constant speed

Page 11
 acceleration = gradient = 0
c
). Non- uniform accelerationi) increasing
acceleration
ii)
decreasing acceleration

Speed(m/s)
d). Uniform deceleration

e). Non- uniform deceleration

Distance travelled in a speed-time graph

Distance travelled = area of rectangle OPRS + area of triangle PQR

Page 12
 = (L x W) + (½ bh)
= (5 s x 20 m/s) + (½ x 5 s x (40 m/s – 20 m/s))
= 100 m + 50 m
= 150 m

EQUATIONS OF MOTION
The equations used to solve problems on motion when the acceleration of the body is uniform.

Page 13
x
SUMMARY OF THE EQUATIONS OF MOTION
v = u + at (does not include s)----1 s = ut + ½ at2 (does not include v)--3
s = ½ (u + v)t (does not include a)---2 v2 = u2 + 2as (does not include t)---4
Note:
s = displacement/distance travelled in metres
u = initial velocity/speed in m/s
v = final velocity/speed in m/s
a = acceleration in m/s2 ( can be + or -
t = time taken
2.6 QUESTIONS
(For the questions below, assume that the motion is in a straight line and that the acceleration is uniform)
1 A motor cycle travelling at 10 m/s accelerates at 4 m/s2 for 8 s.
a) What is its final velocity?
b) How far does it travel during the 8 s?
2 A car accelerates from 8 m/s to 20 m/s in 10 s.
a) What is its acceleration?
b) How far does it travel during the 10 s?
3 A train is travelling at 40 m/s when its brakes are applied. This produces a deceleration of 2 m/s 2.
a) How long does the train take to come to rest?
b) How far does the train travel before stopping?
4 An aircraft accelerates at 25 m/s2. Its take-off speed is 60 m/s.
a) What length of runway does it need to take off?
b) How long does it take to reach its take-off speed?
5 a) Use the values in the table to plot a distance-time graph for a car over a 10 s period
time/s 0 1 2 3 4 5 6 7 8 9 10
distance/m 0 20 40 60 80 100 100 100 100 130 160

b) Describe the motion as fully as you can.

c) What was the average speed over the 10 s?
6 The approximate velocity-time graph for a car on a 5 hour journey is shown below. (There is a very quick
driver change midway to prevent driving fatigue).

Page 14
 a) State in which of the regions OA, AB, BC, CD, DE the car is i) accelerating ii) decelerating
iii) travelling with uniform velocity.
b) Calculate the value of the acceleration, deceleration or constant velocity in each region.
c) What is the distance travelled over each region?
d) What is the total distance travelled?
e) Calculate the average velocity for the whole journey.
7 The distance-time graph for a motor cyclist riding off from rest follows.

a) Describe the motion.

b) How far does the motorbike move in 30 seconds?
c) Calculate the speed.
8 A car runs at a constant speed of 15 m/s for 300 s and then accelerates uniformly to a speed of 25 m/s over a
period of 20 s. This speed is maintained for 300 s before the car is brought to rest with uniform deceleration in
30 s.
a) Draw a speed-time graph to represent the journey described above.
b) From the graph find:
i) the acceleration while the speed changes from 15 m/s to 25 m/s.
ii) the total distance travelled in time described,
iii) the average speed over the time described

2.7 FREE FALLING OBJECTS

2.7.1 ACCELERATION DUE TO GRAVITY (ACCELERATION OF A FREE FALL)
An object falling freely in vacuum under gravitational force of the earth only moves with uniform acceleration known as
acceleration due to gravity (or acceleration of free fall). The acceleration due to gravity is denoted by letter g.
The value of g:-
• is the same for all bodies irrespective of their masses. For this reason, a small body and a large one both dropped
from the same height would move at the same speed and reach the ground at the same time moving at the same
speed if there are no forces opposing their motions.
• varies over the surfaces of the earth, the maximum being at the poles and the minimum at the centre. However the
value of g is taken to be 10 m/s2 on Earth.
• is considered to be constant for a body near the surface of the Earth, however, it decreases with increase in the
altitude.

Page 15
Equations of motion for free fall
For vertical motion a is replaced with g in the equations of motion studied previously.
i) for a dropping object
g = +10 m/s2
v = u + at becomes v = u+gt if the body drops from rest i.e. u =o, v = gt ------------→ (1)
s = ½(u+v)xt ----------------------(2)
s = ut + ½ at2 becomes s = ut + ½ gt2 if u = 0, s = ½ gt2 (note s = height) ----→(3)
v2 = u2 + 2as becomes v2 = u2 + 2gs if u = 0, v2 = 2gs -------------------→ (4

Time/s 0 1 2 3 4 5
Velocity /m/s 0 10 20 30 40 50

Velociy 30
m/s

0 1 2 3 4 5 time/s
Gradient= 10m/s2

* Same equations can be used for bodies thrown/moving vertically upwards but with g as -10 m/s2
NB:- i) velocity at the highest point is zero for any object.
ii) time for upward journey = time for downward journey to the same level
iii) a falling body would pass every point at same speed it did on its way up.

VERTICALLY PROJECTED OBJECT FOR 10 seconds

Time/s 0 1 2 3 4 5 6 7 8 9 10
Speed/m/s 50 40 30 20 10 0 10 20 30 40 50

SPEED
/m/s

0 1 2 3 4 5 6 7 8 9 10

Page 16
Time/s 0 1 2 3 4 5 6 7 8 9 10
Velocity/m/s 50 40 30 20 10 0 -10 -20 -30 -40 -50

Velocity 50
m/s

0 1 2 3 4 5 6 7 8 9 10 time/s

-50

2.7.2 MOTION OF A BODY FALLING AGAINST air Resistance or Liquid Friction

a. At the start
(FR =0, a = 10 m/s2) (FR = W, a = 0)

a. When a body falls in air, initially its acceleration is about 10 m/s 2. b.As its speed increases so does the air resistance
(fluid friction) opposing its motion and this causes the acceleration of the body to decrease. C.Eventually the air resistance
acting upwards equals the force of gravity (weight of the body) acting downwards and the acceleration becomes zero. Then
the body falls with a constant velocity/ speed called its terminal velocity, which is the maximum speed of falling body.
The value of the terminal velocity depends on the surface area, shape and weight of the object.
The effect of air resistance is greater for light object, e.g. raindrop and for bodies with large surface area like a parachute
and is less for heavy bodies.

Page 17
Small dense object has high terminal velocity. It accelerates over a considerable distance before air resistance equals its
weight.

2.7.3 MOTION OF FALLING BODIES IN LIQUIDS

The sketch of the velocity-time graph for body falling

in air or liquid

Same as that one for an object falling in air except that the resistive force here is called upthrust

3.0 MASS, INERTIA, WEIGHT AND CENTRE OF MASS.

3.1 Mass
- is a measure of the amount of a substance (matter) in a body or an object.
- SI unit: kilogram (kg)
- Other units: gram (g), milligram (mg), tonnes (t)
- Measuring instruments:- tripple-beam balance, bathroom balance, lever-arm scale, electronic scale, top-pan
balance.

3.2 INERTIA
-is the tendency of a body to resist any change in its state of motion i.e. to remain at rest if it is at rest or to continue moving
(with uniform velocity in a straight line) if already in motion. The larger the mass of a body the larger its inertia and the more
difficult to change its state of rest or uniform motion or change the direction of its travel. Mass is therefore defined as the
measure of the object’s inertia.
Examples of some effects of inertia in everyday life
a. If a car stops suddenly the occupants are thrown forward because they tend to want to continue moving due
to inertia or if the car starts abruptly the upper part of the occupant is moved back because it seems to want
to remain at rest because of inertia.
b. It is more difficult to move a bigger stone as compared to a small one because of inertia
c.

When card is pulled away very quickly the coin will not move along with it but instead it drops into the glass due to inertia.

3.3 WEIGHT
Definition: is the amount of force gravity acting on object.
Measuring instrument: spring balance/forcemeter

Page 18
SI unit: newton (N).
Unlike mass, the weight of an object is not always constant, it depends on the gravitational pull on a unit mass (gravitational
field strength) at a particular place. On Earth the gravitational pull on a unit mass is 10 N i.e. g = 10 N/kg
On the moon the gravitational pull on a unit mass is 1.6 N i.e. g = 1.6 N/kg.
Mathematically, weight is expressed as:
W = mg
where W = weight in newtons (N)
m = mass in kilograms (kg)
g = gravitational field strength in N/kg.

3.4 QUESTIONS
1) Calculate the weight of a body of mass:
i) 2 kg ii) 700 g
Take g to be 10 N/kg.
2) A bag of coal has a mass of 10 kg on Earth. The acceleration due to gravity is 10 m/s2 on Earth and on the moon
is 1.6 m/s2.

a) What is its mass on the moon?

b) What is its weight on Earth?
c) What is its weight on the moon?

3) A bag of sugar has a weight of 125 N on Earth. Calculate its mass. Take g to be 10 N/kg.

4) State at least three differences between mass and weight.

3.5 CENTRE OF MASS
3.5.1 Definition: is a point on a body at which the whole mass of the body seems to be concentrated.
*Centre of gravity: is a point where the whole weight of the body seems to be concentrated.
The centre of (C.M) of an object:
• Coincides wits centre of gravity (c.g).
• Lies at the centre (middle point) if the body has uniform thickness (density) and regular shape, e.g. the C.M of
a metre rule is considered to be at a 50 cm mark.
• Can be either within or outside the body of the object

3.5.2 C.M of some regular shaped object

*For some objects, (e.g. a ring, retort stand, etc), the C.M lies outside the body of the object, instead it lies in the air around
the object.

3.5.3 C.M of irregular shaped object

Experiment: to determine the C.M of a irregular shaped lamina (a thin sheet of cardboard)

Page 19
Procedure
• Make three holes A, C and E on the cardboard.
• Suspend the cardboard through hole A from a nail clamped on a stand such that it swings freely. When it comes to
rest, its centre of mass will be exactly below point A.
• To identify the point, hang the plumbline from the same nail very close to the cardboard.
• Draw a line AB along the plumbline
• Hang the cardboard from another hole C and repeat the experiment and draw the line CD.
• The C.M lies at the intersection of the two lines.
• To check if the position of C.M is correct, one can hang the cardboard from the third hole E and then draw line EF,
it must also pass through that point.

3.5.4 STABILITY
This defines whether the object falls over easily or not. When the object is slightly displaced and released, it will always
return to its origin (and not topples over) if the vertical line passing through the C.M. is still kept within the base of the object
or the area enclosed by the base of the object (i.e. it has not gone beyond the point of contact between the object and the
surface it is resting on)

Ways of increasing the stability of a body

a) Lowering the centre of mass
b) Widen the base of the object
3.5.5 States of equilibrium
When an object is balanced or stable in its position, it is said to be in equilibrium. Its degree of stability is determined by its
position which can be defined as its state of equilibrium.
Three states of equilibrium are:- 2) Unstable equilibrium
1) Stable equilibrium 3) Neutral equilibrium
1) Stable Equilibrium
A body is in a state or position in which when it is slightly displaced and released it returns to its original position.

When an object in stable equilibrium is slightly tilted, its C.M rises and gain some P.E. When released that extra P.e will be
used to produce an anticlockwise moment about the point of contact that will roll the object back to its original position.
2) Unstable Equilibrium
A body is in unstable equilibrium if it is positioned such that when it is slightly displaced and released it will move further
away its original position ( topples over).

Page 20
 3) Neutral Equilibrium
A state in which a body is positioned such that when it is slightly displaced and released it remains at its new position.

4.0 DENSITY
4.1 Density is defined as the measure of the amount of mass contained in volume of an object. It is usually
expressed as mass per unit volume.
Density = mass/volume
D = m/V or ρ = m/V where ρ(Greek letter rho) = density in kg/m3
m = mass in kg
V = volume in m3
SI unit: kilogram per cubic metre (kg/m )
3

Other UNIT commonly used is gram per cubic centimetre (g/cm3)

1 g/cm3 = 1000 kg/m3
*NB:- Density of pure water is 1 g/cm3 or 1000 kg/m3
4.2 Experiment #1: Measuring density of regular (shaped) object
- Measure the mass m of the object using a balance
- Measure the dimensions of the object and then calculate the volume V of the object using the appropriate formula.
E.g. volume of a cube = l3
Volume of a rectangular block = l x w x h
Volume of a cylinder = πr2h, etc

Page 21
 - Find the density of the object using the equation ρ = m/V
4.3 Experiment #2: Determining the density of an irregular shaped object e.g. a stone
A) Using a measuring cylinder method
- Measure the mass m of the stone using a balance
- Partly fill a measuring cylinder with water and then record the reading of the volume V1 of water. (remember to
read the mark at the bottom of the meniscus).
- Gently lower the stone into water and note the reading V2 (volume of water and stone)
- Calculate the volume of the stone V , using the equation V = V2 – V1.
- Work out the density of the stone using the equation ρ = m/ V.
B) Displacement can method
For larger objects a displacement can may be used

- A beaker or measuring cylinder is placed under the spout and the displacement can is filled with water until it
overflows. The beaker is emptied and replaced.
- Find the mass m of the stone
- The stone is lowered with a thread into the can.
- Overflow is collected in a beaker and its volume is measured to give the volume V of the stone.
- Lastly the density of the stone is found using the equation using the equation ρ = m/V.

4.4.1 Experiment #3: measuring density of a liquid

- Measure the mass m1 of a dry clean beaker
- A convenient volume V of a liquid, let’s say water is run into the beaker and then record the volume V of the water
in cm3.
- Find the mass m2 of the beaker with the liquid in it.
- Then calculate the mass m of the liquid using the equation m = m2 – m1
- Finally calculate the density using
4.4.2 RELATIVE DENSITY
The density of an object can be determined more accurately by finding its relative density.
The relative density of a substance is the ratio of the mass of any volume of the substance to the mass of an equal
volume of water.
R.D = mass of any volume of the substance/mass of an equal volume water
Therefore the density of a liquid can be accurately measured using a density bottle.

4.5 Experiment #4: Measuring the density of a liquid using a density bottle.
- Weigh an empty bottle using a balance

Page 22
 - Fill it completely with water and weigh it once again
- Next replace water with any given substance/liquid e.g. alcohol and then weigh the bottle.
Observations are recorded as below
Mass of the empty bottle = m1
Mass of bottle with water = m2
Mass of water = m 2 – m1
Mass of bottle with alcohol = m3
Mass of alcohol = m 3 – m1
- Density of water =( m2 – m1)/V and density of alcohol = (m3 – m1)/V
Both the liquid and water have the same volume V since the same bottle was used for the whole experiment.
Then R.D of alcohol = density of alcohol/density of water
= (m3 – m1/V)/m2 – m1 /V
= (m3 – m1/V) X V/m2 – m1
= m3 – m1/m2 – m1
Relative density is a ratio so it’s a number without units. However, its value is the same as that of density of a substance in
g/cm3
4.6 Experiment #5: measuring the density of air
- Find the mass m1 of a 500 cm3 rounded bottom flask full of air.
- Remove air from the flask using a vacuum pipe and then determine the mass m2 of an empty flask.
- Fill the flask with water
- Transfer water to a measuring cylinder to find the capacity of the flask which the volume V of air.
- Find the mass m of the air using the equation m = m2 – m1
- Calculate the density of air using the equation ρ = m/V.
4.7 DENSITY OF A MIXTURE
If A is a substance of mass mA and volume of VA and B is a substance of mass mB and a volume VB, the density of the
mixture, ρm is given by :-
( Ρm = mA – mB)/ (VA – VB)

4.8 FLOATING AND SINKING

An object:-
- Floats in a liquid if its density is less than that of the liquid
- Sinks if its density is greater than that of the liquid
- Stays anywhere within the body of a liquid if its density is equal to that of the liquid.

4.9 A HYDROMETER*
It is used to measure the density of the liquids directly. It consists of a thin hollow tube which is weighed(made heavy) at
the bottom with mercury or lead so that it can float upright. The tube has a scale marked on it
The hydrometer floats at different levels/depths in different liquids, depending on their densities. It sinks less in a dense
liquid and sinks more in less dense liquid.
You read the mark level with the surface of the liquid.
Hydrometers are often used to test beer and milk to see if they have too
much water in them.
A special hydrometer called lactometer, used for testing the purity of milk.
A small type of hydrometer enclosed in a larger glass tube fitted with a
rubber bulb. It is used for measuring the density of the battery acid. On
squeezing the bulb and then releasing it acid enters the glass tube and
density can be read on the floating hydrometer.
*At constant temperature the densities of the objects made with the same
material are the same irrespective of
their sizes (volumes)
4.10 QUESTIONS
1 Copy and complete the table shown below.
Length Width Height Volume of rectangular block
2 cm 3 cm 4 cm ...........
5 cm 5 cm ........... 100 cm3

Page 23
 6 cm ............. 5 cm 300 cm3
........... 10 cm 10 cm 500 cm3

2 Calculate the density of the following:

a) a piece of steel which has a volume of 6 cm3 and a mass of 48 g.
b) a piece of copper which has a volume of 10 cm3 and a mass of 90 g.
c) a piece of gold which has a volume of 2.0 cm3 and a mass of 38 g.
3 Calculate the mass of the following:
a) 4 cm3 of aluminium. The density of aluminium is 2.7 g/cm3.
b) 20 cm3 of wood. The density of wood is 0.80 g/cm3.
c) 80 cm3 of glass. The density of glass is 2.5 g/cm3.
4 Calculate the volume of the following:
a) 68 g of mercury. The density of mercury is 13.6 g/cm3.
b) 15.8 g of iron. The density of iron is 7.9 g/cm3.
c) 99 g of lead. The density of lead is 11 g/cm3.
5 A block of material is 8 cm long, 2 cm wide and 3 cm high, and has a mass of 46 g.
a) What is its density?
b) Convert the value of density in (a) above to kg/cm3.
1 A plank of wood is 2.00 m long, 30 cm wide and 3 cm thick.
a) What is the volume of the plank?
b) The density of the wood is 700 kg/m3. What is the mass of the plank?

FORCES
5.1 A force is a push or pull, or a twist exerted by one object on another.
Force is a vector; it has both magnitude and direction in which it acts.
SI unit: newton (N)
*One newton is a force which gives an acceleration of 1 m/s2 to mass of 1 kg.
Examples of forces
1. Gravitational force – an attractive force which any two masses pull one another with.
2. Weight – pulls object towards the centre of the Earth.
3. Friction – tends to stop movement of objects
4. Thrust of a (jet) engine – is a push or pull due to the jet engine
5. Centripetal force – acts on object moving in a circle
6. Tension – produced on a stretched material
7. Magnetic force – acts between magnets or between a magnet and magnetic material
8. Electric force – acts between charges
9. Air resistance/fluid friction/drag – slows down a body travelling through air
10. Upthrust – opposes movement of an object moving in a liquid
11. Force due to expansion/contraction
12. Reaction/normal force – acts on an object on any given surface. The force is normally perpendicular to the
surface and equal and opposite to the weight of the object. It is exerted by the surface on the object.
5.2 EFFECTS OF FORCE
5.2.1 Effects of a force on the shape and size of an object
A force can or tends to change the shape and size of objects, e.g. i) lump of bostik would change shape when pressed, ii) a
inflated balloon changes size when more air is blown into it.
Some of the objects return to their original shapes and sizes when the external force which was previously applied on them
is removed. These objects are called elastic materials, e.g. rubber band, steel spring, etc.
Other objects do not return to their original or sizes even when the force is removed. They will remain permanently
deformed. These are called plastic materials, e.g. plasticine, bostik, clay, etc.
Stretching a spring

Page 24
 LO
L

e = L – Lo where e = extension of the spring

L = new length of stretched spring
L0 = original/normal length of the spring
When the load (weight) which was applied to the spring is removed, the spring returns to its normal length. The
spring is elastic but only to a certain limit.

Experiment: To investigate the relationship between the extension of a spring and load (stretching force)

Procedure
• Suspend a steel spring from a retort stand as shown above
• Attach a pointer in a horizontal position to the end of the spring with some bostik.
• Place a metre rule vertically near the spring
• Suspend the mass hanger on the spring as shown above
• Adjust the height of the ruler such that the pointer is at a convenient reading, say around 30 cm, record this as
initial scale reading.
• Add 100 g (1.0 N) loads one at a time and note and record the new scale reading after each load.
• Record the observations in a table up to 500 g (5.0 N) and calculate the extension for each load.
TABLE OF RESULTS
e = New reading L – Initial scale reading LO
Load F/N Scale reading/cm Extension e/cm F/e (N/cm)
0.0 54.0 0.0 -
1.0 58.0 4.0
2.0 62.0 8.0
3.0 66.0 12.0
4.0 70.2 16.2
5.0 74.0 20.0

Page 25
Graph of load F (force)/N against extension/cm

The graph above is a straight line showing that the extension of the spring is directly proportional to the load i.e. when
the load is doubled the also doubles.
i.e. F α e
then F = ke -------------> Hooke’s law
where F = force applied in newtons (N)
e = extension of the spring in metres (m)
k = constant of proportionality known as force constant or spring constant in N/m
*Force constant k:
• is defined as the amount of force require to give a spring a unit extension.
• is the measure of the stiffness or softness(strength) of a spring (very stiff spring has a high value of k
than a soft one).
• is measured in N/m, N/cm, N/mm, etc.
*Dividing the load by its corresponding extension always gives the same result. This means every 1N increase in
the stretching force produces the same extra

HOOKE’S LAW
If you add more masses to mass hanger and take the corresponding extensions and draw a graph as before, the graph will
be a straight line a curve towards the end showing that towards end load and extension were no longer proportional.

The spring behaves elastically only to point X. Then, the Hooke’s law is obeyed only in the region OX
Therefore Hooke’s law states:
“the extension of a spring is directly proportional to the load/force applied provided the elastic limit of
spring is not exceeded”.
Point X is known as elastic limit or limit of proportionality of the spring. This is point beyond which the spring loses its
elasticity, it would fail to return to its original length even when the load is removed from it. Instead a permanent extension
(deformation) OY will remain on the spring.

IDENTICAL SPRINGS COMBINED IN:

a) SERIES

Page 26
Extension for 1 spring e = x For 1 spring F = ke
2 springs e = 2x e = F/k; e = x
3 springs e= 3x For N springs, e = Nx
4 springs e = 4x Then e = N(F/k)
N springs e = Nx
Then Hooke’s law for N springs in series
e = NF/k ---- total extension for springs in SERIES .

PARALLEL

4 springs e = x/4
N springs e = x/N

From Hooke’s law

For N springs in parallel
e = x/N
e = (F/k)/N
e = F/k X 1/N
e = F/Nk ---------------------------> total extension
for springs in parallel.

For 1 spring e = x
2 springs e = x/2
3 springs e = x/3

QUESTIONS
1. What is the force constant of a spring which is stretched
a) 2 mm by a force of 4 N b) 4 cm by a mass of 200 g.
2. The springs below are identical. If the extension produced in A is 4 cm, what are the extensions in B and C?

Page 27
 3. Tom performed an experiment stretching a spring. She loaded masses on the spring and measured the extension
Table of results

Extension/cm 0 4 8 12 16 20 24
Load/N 0 2 4 6 7.5 8.3 8.6

a) Plot the graph of extension/cm against load/N

b) Calculate the spring constant in elastic behaviour region.

4 The graph below shows how a spring stretches when a force is applied to it.

a) Describe what would happen to the spring if forces were applied to it until it reached point A on the
graph and then the forces are removed.
b) Describe what would happen if the spring was stretched to point B on the graph and then the forces
removed.
c) If a force of 10 N caused the spring to stretch by 5 cm what would be the extension of the spring if 20 N
was applied to it?

5.2.2 EFFECTS OF FORCE ON MOTION OF AN OBJECT

A force can change the state of motion of an object by causing:
(i) its speed to increase or decrease
(ii) its acceleration to increase or decrease
(iii) a change in its direction of travel

Page 28
 (iv) a stationary object start to move or an object in motion stop moving.
All the above can be summed up or explained by Newton’s laws of motion
NEWTON’S LAW OF MOTION
A) First law
It states that
“A body at rest will remain rest or if it is moving it will continue to move with constant velocity (uniform speed in
a straight line) unless an external force makes it to behave differently. It is also known as law of inertia.”
B) Second law
It states that :-
“The acceleration a of a body is
• directly proportional to the force applied F for a fixed mass m
• inversely proportional to the mass m for a fixed force applied F”
Mathematically, newton’s second law of motion is expressed as:-
F = ma
where F = resultant/unbalanced/net force (N)
m = mass of an object (kg)
a = acceleration of the object (m/s2)
C) Third law
It states that:
“if body A exerts a force on body B, body B will exert an equal and opposite force on body A called the reaction
force”
5.3 FRICTIONAL FORCE
5.3.1 Effects of friction on motion of a body
Friction – always acts in opposite to the direction of motion of a body and reduces the acceleration or speed of the body.
Friction acts between solid surfaces as they move over each other and when objects move through gases or liquids.
5.3.2 WHAT CAUSES FORCE FRICTION
It is caused by roughness of the two surfaces in contact, even surfaces which look or feel smooth are rough when seen
under a microscope. As a block of wood slides over the table the humps and hollows on one surface tend to grip those on
the other surface, this causes the frictional force
It is also caused by adhesion between the molecules on the surfaces in contact due to intermolecular forces.
The friction which exists between the two objects when there is no movement is called static friction. The object will start to
move if the pulling/pushing force is increased beyond the value of the static friction. Then the frictional force between the
two surfaces when the object is moving is called sliding/dynamic friction. Usually its value is less than the maximum value of
the static friction.
Calculations involving frictional force
Newton’s second law of motion F = FF – FR F = ma -------------->
Newton’s second law of motion
a = F/m
then for cases where there is friction
a = F/m = FF – FR/m , where a = acceleration in m/s2
FF = forward force in N
FR = frictional force in N
m = mass in kg

Resultant force = forward force – frictional force

From experiments carried out it shows that acceleration is:
(i) Directly proportional to applied force for a fixed mass i.e. a 𝛼 F

Page 29
 1
(ii) Inversely proportional to mass for a fixed force i.e. . a 𝛼
𝑚

Combining the relations in (i) and (ii) we get:

𝐹 F 𝛼 ma
a𝛼𝑚 or

F = kma
Examples
1. A car is acted upon by a forward driving force of 700 N which causes an acceleration. The force of friction between
the road and the tyres is 500 N. Calculate the resultant force on the car.
F = F F - FR
= 700 N – 500 N
= 200 N
2. A car of mass 3 000 kg (including the driver) is travelling at a constant acceleration of 2 m/s 2. The force of friction
between the tyres and the road is 500 N. Calculate the a) resultant force acting on the car b) forward driving
force

Solutions F = F F - FR
a) Data FF = F + F R
m = 3000 kg, a = 2 m/s2 = 6000 N + 500 N
F = ma
= 3000 kg X 2 m/s2 = 6500 N
= 6000 kg m/s-2
= 6000 N
b) Data
F = 6000 N, FR = 500 N

5.4 TURNING EFFECTS OF A FORCE (MOMENT OF A FORCE)

5.4.1 Definition: a moment of a force is the measure of the turning effect of a force. It depends on the size of
the force and how far it is applied from the pivot/fulcrum.
Moment = force X perpendicular distance of line of action of the force from the pivot
M = Fd or M = Fs
where M = moment of the force in newton-metre Nm
F = force applied in newton (N)
d or s = perpendicular distance of line of action from the pivot (m)
Units: Nm, Ncm, etc

Page 30
 M = Fx d

Moment of a force is a vector quantity, i.e. it has magnitude as well as direction. The direction is either clockwise or
anticlockwise, depending in which the force turns the object.
e.g

5.4.2 Experiment: To verify the principle of moments (law of moments/levers)

0
• Pivot the metre rule at the 50 cm.
• Hang the masses m1 and m2 on either side of the pivot until the ruler balances.
• Measure the distance d1 and d2 from the pivot
• Calculate the anticlockwise moment M1 and clockwise moment M2 using equations, M1 = F1d1 &
M 2 = F 2 d2
• Repeat the experiment using different values of m1, m2, d1 and d2
TABLE OF RESULTS
m1/kg F1/N d1/cm M1/Ncm m2/kg F2/N d2/cm M2/Ncm

What do you notice about clockwise and anticlockwise moments when the ruler is balanced?
Answ: the clockwise moment = anticlockwise moment
This observation proves the principle of moments.
The principle of moments* states that:
“when the body is in equilibrium the sum of the clockwise moments about any point is equal to the sum of
anticlockwise moments about the same point”
5.4.3 CONDITIONS FOR EQUILIBRIUM
1) the sum of forces in one direction must equal the sum of the forces in the opposite direction i.e the net force
is equal to zero
2) the principle of moments should be obeyed, i.e. the resultant turning effect is equal to zero.
e.g. The beam below is equilibrium

Page 31
Therefore:
i) Force A + Force B + Force W + Force D = Force C
Then A + B + W+ D – C = 0
ii) Ax + By = Dz
total anticlockwise moments = total clockwise moment
5.4.4 COUPLE*
If two equal forces act on opposite direction they form a couple. A couple cause rotation, e.g turning bicycle handlebars and
steering wheel

To find the moment of a couple, you multiply the value of any of the two forces by the distance between them

M = Fx + Fy
= F(x + y)
= Fd

5.5 CENTRIPETAL FORCE*

This is a type of force that acts on a body moving in a circle/curve and keeps the body in its curved path or orbit. The
centripetal force always points towards the centre of the circular path and that means even the acceleration of the body
(centripetal acceleration) is towards the centre of the curve. The force is provided by the sideways friction between the tyres
and the road surface.

Page 32
5.6 QUESTIONS
Question 1
A student measures the acceleration of a trolley. The light sensors are connected to a computer which is programmed to
calculate the acceleration. The results obtained are recorded in a table as follows.
Force(N) 0 1 2 3 4 5
Acceleration(m/s2) 0 0.5 1.0 1.5 2.0 2.5

i) Plot a graph of acceleration(m/s2) against force(N)

ii) Describe how changing the force affects the acceleration.
iii) Write down, in words, the equation connecting force, mass and acceleration.
iv) Use the data from the graph to calculate the mass of the trolley.
v) On graph, sketch the graph line that would be obtained for a trolley of larger
mass.

Question 2
A car has a mass of 900 kg. It accelerates from rest at a rate of 1.2 m/s2.
a) Calculate the time taken to reach a velocity of 30 m/s.
b) Calculate the force required to accelerate the car at a rate of 1.2 m/s2.
c) Even with the engine working at full power, the car’s acceleration decreases as
the car goes faster. Why is this?

Question 3
The diagram below shows some of the forces acting on a car of mass 500 kg.

a) State the size of the total drag force when the car is travelling at a constant
speed.
b) The driving force is increased to 3000 N.
i) Find the resultant force on the car at this instant.
ii) Calculate the initial acceleration of the car.

Question 4
The manufacturer of a car gave the following information; Mass of car = 1000 kg. The car will accelerate from 0 to 30 m/s in
12 seconds.
a) Calculate the average acceleration of the car during the 12 seconds.
b) Calculate the force needed to produce this acceleration.
Question 5
a). What constant braking force is needed to bring a car of mass 1200 kg to rest in
5 s when it is moving at 20 m s-1?

Page 33
b). A car of mass 800 kg is moving at 25 m s-1. Calculate the force needed to bring
the car to rest over a distance of 20 m.
c). A body is initially in motion. If no external force acts on the body how will its
motion change?

Question 6

On the diagram show the forces and their direction.

Question 7
Fig. 6.1 shows a car of mass 500 kg moving from rest with constant acceleration of 10 m/s 2. Two forces act on it, a forward
force and a friction force.

Fig. 6.1
a). (i) Calculate the resultant force acting on the car. Show your working.
(ii) If the friction force is 2000 N, calculate the forward force acting on the car.
Show your working.
(iii) After some time, the car reaches a velocity of 20 m/s. How long did it take for
the car to reach this velocity?

Question 8
Fig. 7.1 shows a metal ball being dropped from the surface of oil in a tube of length 2 m. the ball has a mass of 1 kg and it
moves with constant acceleration of 5 m/s2.

Fig. 7.1
(a) Calculate the resultant force acting on the ball.
(b) Calculate the friction caused by the oil. (g = 10 N/kg).
(c) Calculate the time taken by the ball to reach the bottom of the tube.

Question 8
Fig. 8.1 shows a model crane. The crane has a movable counterbalance.

Page 34
(a) Why does the crane need a counterbalance?
(b) Why does the counterbalance need to be movable?
Refer to Fig. 8.1
(c) What is the moment of the 100 N force about O?
(d) To balance the crane, what moment must the 400 N force have?
(e) How far from O should the counterbalance be positioned?
(f) Where would you expect the counterbalance to be positioned if the crane is
lifting its maximum load?
(g) What is the maximum load the crane should lift?
(h) Describe two ways of making the design of the crane more stable.
9 The diagram below shows a spanner being used to undo a nut on a car wheel.

a) Calculate the moment created by the force trying to undo the nut.
b) Suggest how you could increase the moment applied to the nut without
increasing the applied force.

10. The diagrams show forces acting on various beams. For each beam, the fulcrum
is at its midpoint. Which of the beams are in equilibrium? What happens in the
other cases? What is the upward force of the fulcrum on the beam in each
case?

11. A 1 N weight is hung from the 5 cm mark of a metre rule. The rule balances on a
knife edge at the 30 cm mark. What is the weight of the rule?

Page 35
12 The diagram shows a beam balanced with the fulcrum at the midpoint. How big
is the force X?
13. The diagram shows two beams balanced with the fulcrum at the midpoint. In
each case, what is the distance x?

5.7 SCALARS AND VECTORS

5.7.1 DEFINITIONS
SCALAR QUANTITY: expressed in terms of magnitude/size only, e.g. distance, temperature, time, etc.
VECTOR QUANTITY: expressed in terms of magnitude and direction, e.g. force, acceleration, moment, velocity, etc.
5.7.2 Addition of vectors*
1. Resultant of 3 N and 7 N forces at a right angle to one another.
i) GRAPHICAL METHOD
Choose a suitable scale; 1 cm : 1 N

After drawing the vector diagram to scale, you measure the length of line that represents the resultant and then use the
chosen scale to find the resultant..
Length = 7.6 cm, therefore resultant = 7.6 N
Direction is obtained by measuring the angle between the resultant force and one of the forces, e.g. 23° to the
7N
R = 7.6 N, 23° to the 7 N
ii) Algebraically
For right-angled triangle – use Pythagoras theorem
c2 = a 2 + b 2
OR2 = OP2 + PR2
= (7 N)2 + (3 N)2
= 58 N2
OR = √58 N2
Resultant R = 7.6 N
for direction trignometrical functions

Page 36
 sinθ = OPP/HYP cosθ = ADJ/HYP tanθ = OPP/ADJ
e.g. sinθ = OP/OR, cosθ = PR/OR tanθ = OP/PR
sinθ = 3/7.6 cosθ = 7/7.6 tanθ = 3/7
θ = sin-1(0.3974) θ = cos-1(0.921) θ = tan-1(0.4286)
= 23° = 23° = 23°
2. Forces acting at an angle not 90° to each other
PARALLELOGRAM RULE*
If two forces acting at appoint are represented in magnitude and direction by the sides of a parallelogram, the resultant
is represented in size and direction by the diagonal of the parallelogram.
E.g. Find the resultant of forces of 3500 N and 2500 N acting at an angle of 60° to each other
Using parallelogram rule (graphical method)
Scale 1 cm : 500 N

Resultant force = 10.5 x 500 N = 5250 N

Direction = angle between the resultant and the 3500 N force (measure using a protractor) = 24°
ALGEBRICALLY*,
Use cosine rule
c2 = a2 + b2 – 2abcosΦ
To find the direction, use sine rule
a/sin A = b/sin B = c/sin C
5.7.3 Resolving a force*
When a single is converted into components it is said to be resolved. Components together have the same effect as that of
the single force. Usually the components are at the right angle to one another.

The components of the resultant force F are FX (OB) along the x-axis and Fy (OA) along the y-axis.
To find FX and FY
Using trigonometry
sinθ = OA/OC cosθ = OB/OC
sinθ = Fy/F cosθ = Fx/F
Fy = Fsinθ Fx = Fcosθ
e.g. If F = 200 N, θ = 30°
O
Fy = F sin Fx = Fcos30° B
= 200sin30° Fx = 200cos30°
= 100 N = 173 N
5.7.4 QUESTIONS
1. How is a scalar different from a vector? Give an example of each.
2. Forces of 12 N and 5 N both act at the same point, but their directions can be varied.
a) What is their greatest possible resultant?
b) What is their least possible resultant?
c) If the two forces are at right angles, find by scale drawing or otherwise the size and direction of their
resultant.
3. Find the resultant of a displacement of 5 m north-east and one of 3.5 m due east.. (State the size of the
displacement as well as its direction). What would your answer have been if the second displacement had
been due south instead of due east.

Page 37
4. Which of the following quantities are scalar quantities; temperature, potential energy, density, weight
5. Fig. 5.1 shows a heavy block hanging from two ropes so that it does not move. The forces and the angles are
shown. Draw a vector diagram to find the resultant force exerted by the ropes on the block. Say what scale
you have used.

Fig. 5.2

6.0 WORK, ENERGY, POWER AND EFFECIENCY

6.1 WORK
Work is done when a force moves an object in its direction.
It is given by the product of force and the distance moved in the direction of the force
The SI unit of work is a joule (J).
W = Fs 1J=1NX1m
where W = work done in joules (J) = 1 Nm
F = force in newtons (N) Other units (larger): kilojoule (KJ) ; 1 KJ = 1000 J
s = distance moved in metres (m) Megajoule (MJ); 1 MJ = 106 J
*Note: No work is done if :-
i) the force applied on the object does not move the object
ii) the direction of motion is perpendicular to the direction of force.
6.2 ENERGY
6.2.1 Energy is a measure of the ability or capacity to do work.
Work done and energy transferred
When a body A does work on body B, body A transfers energy to body B. The amount of energy transferred from body A to
body B is equal to the work done by body A on body B.
WORK DONE = ENERGY TANSFERRED

Energy is also measured in joules (J)

6.2.2 DIFFERENT FORMS OF ENERGY
• Chemical energy • Sound energy
• Electrical energy • Mechanical energy
• Heat/thermal energy • Light energy
• Nuclear energy
• Radiant energy – given out by source in form of wave, e.g light, microwave, sound, heat, etc
6.2.3 MECHANICAL ENERGY
There are two types of mechanical energy
• Potential energy (Pe)

Page 38
 • Kinetic energy (Ke)
(1) Potential energy
Is the energy possessed by a body due to its position or condition. There are two kinds:- i) gravitational potential
energy ii) elastic potential energy
A stretched elastic rubber band has elastic potential energy
An object suspended above the ground has gravitational potential energy
The work done in lifting up a body is converted into gravitational potential energy of the body
Gravitational potential energy = weight X height

GPe = mgh

where g = acceleration due to gravity in m/s2

m = mass of the object in kg
h = height in metres (m)
2) Kinetic energy
Kinetic energy is possessed by a moving object.
Ke = ½ mv2
where m = mass (kg)
v = velocity (m/s)

6.2.4 PRINCIPLE OF CONSERVATION OF ENERGY

It states that:-
“Energy can neither be created nor destroyed but it can only be converted from one form to
another and the total amount remains constant”.
Examples
#1. In the case of the ball falling vertically downwards from height h

• Its energy is all PE at the beginning of the fall

• Gains some K.E and loses P.E as it falls and its velocity increases and height decreases.
• The increase in K.E is equal to the lose in K.E
• On reaching the ground all energy will be changed to K.E and P.E is zero.
• y
*K.E = ½ mv2 = mgh
which follows that velocity on reaching the ground is given by:
½ mv2 = mgh
v2 = 2gh
• At any moment the total energy is constant; P.E at the beginning = K.E at time the ball hits the ground = sum
of K.E + PE at intermediate positions.
• When the ball bounces, only rises to a lower height showing that it has less GPE now compared to the
previous maximum height. This is because some energy is lost during its impact with the ground mainly as
heat.
#2. A swinging pendulum

Page 39
 • Energy all PE at the extreme positions.
• All energy KE when passing the resting
position.
• Partly KE and partly PE at the intermediate
positions (the sum of the two is always equal to
the total energy)
• The pendulum will eventually stop swinging
because all the energy would be lost to the
surrounding as heat energy due to doing work
against friction (air resistance).

6.2.5 Energy changes/transfers - examples;

Action device/transducer Energy changes
Lifting a weight Chemical energy --------→ PE
Dropping the weight PE ------→ KE -----------→ heat + sound
Electric motor Electrical ------------→ KE
Burning candle Chemical ---------→ heat + light
Generator KE -----------------→ electrical
Microphone Sound -------------→ electrical
Loudspeaker Electrical ------------→ sound
Hot air balloon Heat ---------------→ PE
Battery torch Chemical ---------------→ electrical

6.2.6 MAJOR SOURCES OF ENERGY

1. CHEMICAL OR FUEL ENERGY
Sources: coal, oil, food, electric cells, explosives, etc
When a material combines with oxygen, e.g. during burning, their atoms regroup and releases their chemical energy in
some other forms such as heat.
i) Energy conversion at coal power stations
Chemical energy (coal) -----→ heat energy (water/boiler) -----→ internal energy(steam) ----→kinetic energy (turbines) --→
kinetic energy (generator) ------→ electrical energy
Internal energy: PE + KE of the molecules.
ii) Energy conversion when a battery is used to light a bulb/lamp
Chemical ------→ electrical ------→ light + heat
iii) Energy conversion when electricity is used to charge a battery
Electrical ------------------→ chemical energy.
Advantages of chemical energy
• Currently available in large quantities
• Power stations are relatively cheap to build and operate compared to nuclear power station.
Disadvantages
• Non-renewable- they will eventually run out.
• Cause pollution (which increases the greenhouse effect and also produce acid rain and cause health)
2. HYDRO-ELECTRICITY
When water in a high reservoir is allowed to fall it turns the water turbines which in turn drive the generator and produce
electricity.
GPE(water) -----→ KE(water) -------→ KE(turbines) ------→KE(generator) -----------→ electrical energy
ADVANTAGES • Depends on rainfall
• Is a renewable source of energy • Large areas of countryside must be covered
• Causes no pollution with water, displacing people from their homes
DISADVANTAGES and animals from their natural habitants.
3. WIND ENERGY

Page 40
Wind is used to turn turbines / blades attached to magnets in generators called AEROMAGNETS. .
KE(wind) ------→ KE(turbines) -----→ KE(generator) --------→ electrical energy
• Unpredictable – wind may not be sufficient
ADVANTAGES enough to turn the generator when electricity is
• Wind is free needed.
• Give high power output • High cost involved in implementing and
• Renewable maintaining.
• Clean • Power output is fairly low.

DISADVANTAGES

4. SOLAR ENERGY
We receive energy from the sun as radiant energy in form of electromagnetic waves. The source of solar energy is the
nuclear energy released through nuclear fission of the nuclei of hydrogen atoms.
Solar energy can be captured in several ways:-
• Photovoltaic cells convert light energy into electricity
• Solar panels absorb heat from the sun. The energy is usually used to heat water.
• Solar furnances: an array of concave mirrors which concentrate the sun rays producing very high
temperatures of more than 3000 °C.
• Power generation reflectors are used to focus heat from the sun on tubes filled with oil. The oil boils
water and the steam is sent to the turbines which turns the generators to produce electricity.
Heat (infrared from the sun) → internal energy (steam)→kinetic (turbines)→kinetic(generators)→electrical
ADVANTAGES
• Clean • Renewable
• Relatively cheap
DISADVANTAGES
• Useful only in places where the sun shines continuously for long period; sometimes the sun does not
shine or not strong enough in some parts of the country.
5. WAVE ENERGY
The rocking motion of the waves generate energy DISADVANTAGES
ADVANTAGES • Very inefficient way to capture
• Renewable source of energy energy
6. GEOTHERMAL ENERGY
It is heat energy stored inside the rocks underground. The rocks are heated by some radioactive elements as they are
heated by the sun.
The water is pumped down a borehole to hot rocks underground where it is heated. Steam under high pressure comes
through the other hole, it is used to turn the turbine which in turn drives the generator.
Geothermal (rocks)→internal energy(steam)→kinetic (turbine)→kinetic(generator)→electrical
7. TIDAL ENERGY
Sea water is trapped at high tides behind the dams and released at low tides. The released H2O is used to turn turbines
ADVANTAGES DISADVANTAGES
• Renewable • High initial cost
8. NUCLEAR ENERGY
a). Fission – splitting of heavy nucleus (U-235) by hitting it with a neutron into nearly two equal parts to release
tremendous amount of energy and two to three more neutrons.
b). Fusion- union of certain light nuclei (e.g isotopes of hydrogen) into a heavier nucleus resulting in the
release of large amount of energy.
Uranium is the fuel in nuclear reactors. By the process of fission, the nuclear energy in uranium is converted to large amount
of heat energy.
Nuclear energy ----> heat---->k.e of steam ---> k.e of turbines----> k.e of generator---->electrical energy
ADVANTAGES • Reliable- most viable source of
• Lots of energy from little amount large amount of electrical energy
of fuels • Low cost once up and running
• Little atmospheric pollution DISADVANTAGES
provided strict precautions are • Can be dangerous
taken
Page 41
 • High cost of building power station • High cost of dismantling once they
• Non-renewable can no longer be used.
6.2.7 Sources of energy in Botswana
1. Biogas: cow dung ferments in a closed container can produce a gas that is used as fuel. This gas burns and so it
can be used in cookers.
2. Petrol and Diesel:- vehicles and borehole pumps are driven by engines that burn these fuels
3. Morupule Power Station:- coal is mined at Morupule and is burned in power station. The heat is used to boil
water and produce steam. The steam goes through the turbine and makes it rotate. The turbine makes the
generator rotate and produce electricity.
4. Wind power
5. Solar power
6. Others are: candles, wood, bottle gas
6.3 POWER
Power is the rate of doing work or transferring energy to
other form/s.
Power = work done/time taken SI unit:- watt (W)
P = W/t 1 W = 1 J/s
Other units:
1 kilowatt (kW) = 103 W
OR
1 megawatt (MW) = 106 W
P = E/t

MEASURING HUMAN POWER

A person’s power can be calculated by timing the work she/he is doing, e.g. running up on stairs
Suppose a girl weighing 500 N climbs 6 stairs each 25 cm high in 5 seconds
W = weight X height P = w/t
= 500 N X (6 X 0.25 m) = 750 J/5 s
= 750 J = 150 W
Calculate the average power
6.4 EFFICIENCY
-is the ratio of useful work done by a machine to the energy input, often written as a percentage
Efficiency = (useful work done/total energy input) x 100 %
OR
Efficiency = (power output/power input) x 100 %
NB:- in real life, there is no machine that is 100 % efficient because there is always some energy lost as heat as
result of work done against friction between the moving parts of the machine.
6.5 QUESTIONS
1. A horizontal force of 50 N is applied onto a box which then moves a distance of 2 m. How much work is done
on the box?
2. A can of 500 g is lifted onto a shelf through a vertical height of 1.5 m. How much work is done?
3. A man pushes a box across the floor by applying a horizontal force of 100 N. The box travels with a constant
speed of 0.5 m/s.
a) What is the distance moved by the box in 10 s?
b) Calculate the work done on the box in 10 s.
4. A builder lifts 10 bricks to the top of a building through a vertical distance of 5 m. Each brick has a mass of
500 g.
a) Calculate the work done by the builder.
b) If it takes 20 s to lift the bricks at what rate is the builder working?
c) State form of energy gained by the bricks.
5. A body of mass 5 kg falls from rest and has k.e of 1000 J just before it touches the ground. Assuming there is
no friction and using the value 10 m/s2 for the acceleration due to gravity. Calculate the loss of potential
energy during the fall.
6. A 100 g steel ball falls from a height of 1.8 m onto a plate. Calculate
a) the G.P.E of the ball before the fall.
b) its k.e as it hits the plate.
c) Its velocity as it hits the plate.
7. The diagram below shows a model power-station. A small steam engine drives a generator which

Page 42
 lights a bulb. Decide where each of the following energy changes is taking place. (You can answer
by writing one of the letters A – D in each case.)

a) Kinetic energy to electrical energy: …………………………………….

b) Heat energy to kinetic energy: ………………………………
c) Electrical energy to heat and light energy: ………………………..
d) Chemical energy to heat energy: ………………………..

8. Some workers on a building site have set up an electric winch in order to lift a
bucket with tiles up to the roof. The bucket and tiles weigh 500 N.
a) What is the minimum force that must be applied in order to lift the bucket of
tiles off the ground?
b) How much energy is spent in lifting the tiles 20 m from the ground to the
roof?
c) What energy transformations are taking place as the tiles are raised?
d) If the tiles are lifted 20 m in 10 s, what is the power of the winch?
e) If the winch is only 50 % efficient, how much energy must be fed into the
electrical motor to lift the tiles through the 20 m?
f) Suggest one or two reason why the system might be less than 100 % efficient.
g) How can the efficiency of the system be improved?
9. In a certain ward in Serowe people use solar panels and windmills as energy
sources.

(a) Write down one advantage of using each of these energy sources
i) solar panels:
ii) windmills:
(b) Write down one disadvantage of using solar panels
(c) Write down one disadvantage of using windmills
10. The diagram below shows a hydroelectric scheme. Water rushes down from the
top of the lake to the power-station. In the power-station, the water turns a
turbine which drives a generator.

Page 43
 a) What type of energy does the water have when it reaches the power-
station?
b) Some of the water’s energy is wasted.
(i) Why is energy wasted?
(ii) What happens to the wasted energy?
c) The hydroelectric scheme is a renewable energy source. What is meant by
a renewable energy resource?
d) When water flows from the lake, potential energy is lost. How is this energy
replaced?
e) What advantages does a hydroelectric scheme have over a fuel-burning
power-station?
f) What environmental damage does a hydroelectric scheme cause?
11. At night time when most of us are asleep the demand for electricity is quite
small. The generators at the power stations, however, are still working as it is very
wasteful and inefficient to turn them off. In some power stations the excess
electrical energy they are manufacturing is used to pump water into dams.
Then during the day the water is released and used to drive
generators when demand is high.
a) What weight of water can be pumped 50 m uphill if the surplus energy from
a generator is 2 MJ?
b) When released, how much kinetic energy will this have after it has fallen
(i) 25 m (ii) 50 m?
c) What assumptions have you made in order to answer (b) above?
d) Suggest why off-peak night-time electricity is cheaper than daytime
electricity.
13. To be a good pole vaulter it is essential not only to be strong and agile but also
to have good sprinting speed.
a) What kind of energy does a vaulter possess;
(i) before starting his run?
(ii) as he sprints down the runway?
(iii) as he clears the bar?
b) When a competitor has completed his vault where has all the energy
gone?

7.0 PRESSURE
1 Pressure is force per unit area 1 Pa = 1 N/m2
Pressure = force/area Pressure increase with:-
P = F/A i). Increase in force
SI unit :- pascal (Pa) ii). Decrease in the area of contact

Examples
#1. A concrete block has a mass of 2600 kg. If the block measures 0.5 m by 1.0 m by 2.0 m. What is the
maximum pressure that it can exert when resting on the ground?
Data #2. What force is produced if a force of 1000 Pa acts on
F = 26000 N, A = (0.5 X 1.0) m = 0.5 m2 an area of 0.2 m2.
Data
P = F/A F = 1000 N, A = 0.2 m2
= 26000 N/0.5 m2 P = F/A
= 52 000 N/m2 F = P(A)
= 52 000 Pa = 52 kPa =1000 N/m2 x 0.2 m2
= 200 N
#3. Explain why a tractor’s big tyres stop sinking to far into the soft soil
Answ: Exert less pressure on the soil because of small area contact between the tyres and the

Page 44
 soil/ground

7.2 LIQUID PRESSURE

1. Pressure in a liquid increases with depth; the further down you go, the greater the weight of the liquid above.

Water spurts out fastest and furthest from the lowest from the lowest hole.
2. Pressure at one depth acts equally in all directions

The can of water has similar holes all round it at the same level. Water comes out as fast as far from each hole. Hence the
pressure exerted by the water at this depth is the same in all directions.

3. A liquid finds its own level

In the U-tube the liquid pressure at the foot of P is greater than at the foot of Q because the left hand column is
higher than the right one. When the clip is opened the liquid moves from P to Q until the pressure in both is the
same and the levels of liquid in both column are equal.
b.

Page 45
 The liquid is at the same level. This confirms that pressure at the foot of a liquid column depends only on the
vertical depth of the liquid and not the width or shape of the tube.
7.3 HYDRAULIC MACHINES
A liquid is incompressible therefore its volume cannot be reduced by squeezing. Pressure in a liquid is therefore transmitted
in hydraulic machines to magnify a force.

Pressure, piston A = 100 N/m2 x 0.5 m2

PA = FA/AA = 50 N
= 1.0 N/0.01 m2
= 100 Pa A force of 1.0 N is therefore magnified 50 times.
The pressure is transmitted wholly through the liquid to Note:
piston B PA = PB
Force in piston B FA/AA = FB/AB
FB = PBAB note: PB = PA
FA = (AA/AB)FB; AA/AB = force multiplying factor

7.5.1 ATMOSPHERIC PRESSURE (AIR PRESSURE)

Owing to its weight, air exerts pressure at the surface of the earth and objects on the surface of the Earth. The air pressure
at the sea level (known as the standard atmospheric pressure, PO) is 105 Pa (100 kPa)
7.5.2 EFFECTS OF AIR PRESSURE
Collapsing/crushing a can

After removing (pumping out the air) it becomes very

difficult to separate the spheres because air pressure
inside is less than outside.

If air is removed from the can it collapses because the

pressure inside the can becomes or is less than outside.

Magdeburg hemisphere
7.5.3 AIR PRESSURE GAUGES

Page 46
 a) U-tube manometer

In diagram (a) atmospheric pressure acts equally on both arms of the tube. The levels of the water (liquid) inside therefre are
the same. In diagram (b) arm one arm is connected to a gas cylinder which exerts pressure to the liquid and it rises to the
height h in the other arm.
Pressure of the gas = Atmospheric pressure + Pressure due to the liquid column h
P = PO + hρg
Pressure of the liquid column h is therefore equal to the amount by which the gas supply exceeds atmospheric pressure.
b) Mercury Barometer

A mercury barometer is a manometer which is used to measure atmospheric pressure. Atmospheric pressure acts on the
surface of the mercury in the bowl and maintains the height of the liquid column h. This height is 760 mm at sea level. When
the pressure acting on the surface of the mercury in the bowl is reduced, the height h decreases. When the barometer is
slightly tilted the height h is not affected because atmospheric pressure acts equally in all directions.
Pressure at x due to the liquid column h equals the atmospheric pressure on the surface of mercury in the bowl. This
pressure is stated in terms of height of the mercury column e.g. 760 mmHg (at sea level), 74 mmHg, etc. Increasing the
diameter of the tube doesn’t change the pressure at x because the weight of the liquid column (force) will now be acting on a
large surface area.
7.6 Weather maps
Weather maps are constructed by plotting of pressure readings from different weather stations in a region. When this has
been done, lines known as isobars are drawn.
Isobars are lines drawn on the map weather to join places of equal atmospheric pressure. Closely spaced isobars
indicate a big pressure difference over a short distance and suggest that strong winds are likely to occur. Widely spaced
isobars indicate a small pressure difference over a large area and suggest light winds,
Winds blow from places of high atmospheric pressure to places of low atmospheric pressure. Because of the rotation of the
Earth, winds blow more or less along the isobars. Winds blow in a clockwise direction in an anticlockwise direction in the
southern hemisphere for an anticyclone(High Pressure Region) . For a cyclone they blow in clockwise direction in the
southern hemisphere and in the anticlockwise in the northern hemisphere.
In weather a region of high atmospheric region surrounded by places of low pressure is called a HIGH OR AN
ANTICYCLONE and region of low atmospheric pressure in the middle of high pressures is called a LOW OR CYCLONE OR
DEPRESSION

Page 47
 CYCLONE ANTICYCLONE-High Pressure zone

7.7 QUESTIONS
1. a) A thumb tack is squeezed between finger and thumb as shown in Fig. 1.1. Which experiences the
greater pressure, thumb or the finger? Explain your answer.

Fig. 1.1
b) A hippopotamus has very large feet. How do the large feet help the hippo to walk on soft mud?
c) Why is a dam built thicker at the bottom than at the top?
2. Explain why air pressure decreases as height above the Earth increases.
3. Explain, in terms of pressure, how you are able to drink liquid by using a straw.
4. Fig. 4.1 shows a simple mercury barometer.

a) What occupies the space labelled X?

b) Copy the diagram and show on it the distance which would be measured to find the atmospheric
pressure?
c) If the atmospheric pressure rises, what happens to (a) the mercury level in the tube, (b) the mercury
level in the reservoir?
d) Explain what would happen to the mercury if the barometer is slowly slanted out of the vertical.
5. The oil in a tank is 1.5 m deep and it has a density of 800 kg/m 3. What pressure does the oil exert on the
base of the tank, in pascals?
6. A bench top measures 2 m x 1 m. atmospheric pressure is 100 000 Pa. What is the downward force of the air
on the bench top? How many tonnes of air would have this weight? (1 t = 1000 kg) Why does the bench top
not collapse?

Page 48
 8.0 THERMAL PHYSICS
8.1 MATTER
Matter is defined as anything that occupies space and has mass.
8.1.1 Kinetic molecular model of matter
The kinetic theory of matter states that
• All matter is made up of very tiny particles (molecules).
• The particles of matter are in constant, random motion.
• There are forces of attraction between the particles (the force is called a bond). It holds particles together in solid
and liquid. But it is almost negligible in gases.
• There spaces between the molecules.
8.1.2 Intermolecular forces
- Are electromagnetic in nature due to electric and magnetic forces between particles.
- Can either be attractive or repulsive depending on the distance between the particles. If the particles come closer
together than their normal spacing, the force is repulsive and is relatively large to push them apart. If the
separation of the particles is slightly more than their normal spacing, the force is attractive and relatively large to
push them back.
8.1.3 SOLIDS
• Particles are close together and arranged in regular form lattice.
• Most of true solids exist as a regular three dimensional structures called crystals.
• Have definite shapes and volumes
• Each particle has a fixed position in the crystal lattice.
• Particles vibrate slightly from their fixed positions but the intermolecular forces are strong enough to prevent the
molecules from moving out of their positions to other positions.

Page 49
8.1.4 LIQUIDS
• Particles are little further apart than those in solids
• Particles have no fixed positions.
• Have definite volumes but no definite shapes.
• Have slightly weaker intermolecular forces
• Particles are free to slide over each other in a random motion.
8.1.5 GASES
• Particles are much further apart (so gases are less dense and can easily be compressed)
• Particles are in continuous motion with high speed in all directions (random motion), completely independent of
one another.
• Intermolecular forces are negligible (almost non-existent) except during collisions.
• Have neither fixed volumes nor fixed shapes (always expand to fill the whole container).

A diagram to illustrate a typical motion of a gas particle

8.2.1 TEMPERATURE AND KINETIC ENERGY

The average of the kinetic energy of molecules is directly proportional to its temperature in kelvins. Doubling the kelvin
temperature of a gas doubles its molecular energy.
The total energy of molecules consists:-
a). kinetic energy which depends on temperature.
b). potential energy which depends on the force between molecules and the distance in-between.

*NB:- At any instant, different particles have different amount of kinetic energy. On heating, the kinetic energy of
the particles (also their average kinetic energy) increases.
The temperature of a substance is the measure of the average kinetic energy of its particles.
At any given temperature, particles of any two gases have the same kinetic energy but their average speed are not the
same.

8.2.2 Pressure of a gas in terms of molecular forces

Gases consist of large number of particles in constant random motion. Gas pressure is a result of force exerted on the
Internal surface AREA of the container walls by the gas particles as they strike walls and rebound.

8.3 GAS LAWS

8.3.1 PRESSURE LAW- Relationship between KELVIN Temperature and Pressure ( Volume Constant)
Pressure law states that:-
“ The pressure of a fixed mass of gas at constant volume is proportional to its temperature”
P α T : when volume is constant. --------------> Pressure law
P/T = a constant P 1 / T 1 =P 2T 2

The pressure of a gas increases with increase in temperature because the particles collide with the container walls:- i) more
frequently each second and ii) with greater force as the increase in temperature increase their kinetic energy.
8.3.2 Boyle’s Law- PRESSURE AND VOLUME( Temperature Constant)
Boyle’s law states that:-
“The volume of a fixed mass of gas is inversely proportional to the pressure, provided the temperature
remains constant”. P α 1/V when temperature is constant --------> Boyle’s law

P 1 V1 = P2 V2 ------------------------------( Temperature Constant)

When the volume of a given mass of a gas is decreased;

a). the particles have less space to move in,
b). so particles collide more frequently each second with the walls,
c). as a result the force and pressure increase.

Page 50
8.3.3 Charles’ law- VOLUME AND KELVIN TEMPERATURE
When a gas is heated, its temperature rises as its particles move faster. If pressure of the gas is to remain constant, the
volume must increase so that the number of collisions of the particles with walls does not more frequent and violent and
hence increase the pressure.
VαT when pressure is constant------------CHARLE’S LAW

8.4 EXPERIMENTAL EVIDENCE FOR THE EXISTENCE OF MOLECULAR MOTION

8.4.2 BROWNIAN MOTION
The random motion of small sized particles in a fluid (such as smoke particles in air) that is seen when viewed through a
microscope. The motion of the particles is due to the collision with fast moving air molecules.
Experiment : Demonstration of Brownian Motion

Apparatus are set as shown above in a dark room. The smoke cell is filled with smoke from smouldering paper and it is
brightly lit.
On viewing through a microscope, the smoke particles (seen as pin points of light due to light reflected by them) are seen to
move at random in erratic zigzag manner . THE explanation is due to the collision of air molecules with the smoke particles.
Explanation of Brownian motion using the kinetic theory
Brownian motion is due to the continuous bombardment of tiny smoke particles by numerous air molecules which are too
small to be seen.
The air molecules move with different velocities in different directions. The resultant force on the smoke particles is therefore
unbalanced and irregular in magnitude and directions. This causes the smoke particles to move to a new position now and
then when another unbalanced force acts on it. All these result into the random motion of the particles.

8.5 QUESTIONS
1 Describe the spacing of molecules and their movement in solids, liquids and gases.
2 What do each of the following statements tell you about the forces between atoms?
a) It is not easy to stretch or compress a metal.
b) If the extension is not too big, a stretched copper wire regains its original length when the stretching force
is removed?
3. A bubble of air released from a diver’s helmet under water rises to the surface. As it rises, its diameter
increases. Explain why.
4. Explain the following results.
a) A gas inside a container exerts a pressure on the walls of the container.
b) The pressure increases when the mass of the gas in the container is increased.
Page 51
5. Some smoked-filled air is put into a clear plastic box and viewed through a microscope.
a) Describe carefully what is seen through the microscope.
b) Use the molecular model of gases to explain what is seen.

8.6 THERMAL EXPANSION

8.6.1 Thermal Expansion and Contraction IN SOLIDS
Most solids expand when heated and contract on cooling. When a solid is heated, its particles vibrate more vigorously and
faster. As the vibrations become larger the particles will need more space for movement, so particles are pushed further
apart and the solid expands slightly in all directions.
When it is cooled, the vibrations become smaller then the particles are pulled closer together by force of attraction between
and hence the solid contracts.
Demonstration of expansion of solids
1). Ball and ring experiment

When the ball and the ring are at the same temperature, the ball fits into the ring and can pass through easily.
Procedure : - Heat the ball strongly several minutes
- Try to pass the ball through the ring
Observation: the ball does not fall through the ring
Conclusion: solid expands when heated.
b) Then, leave the ball to rest on the ring for some minutes.
Observation: The ball falls through the ring
Conclusion: The ball lost heat to the ring and contracts as it cools and at the same time the ring expands as it
gains the heat.

2). Bar and gauge

The gauge consists of a slot that fits in the length of the bar and a circular hole that fits in the diameter of the slot when both
the gauge and bar are at the same temperature.

Procedure:
- Fit the bar into the slot and the hole on the gauge when both the gauge and bar are at room temperature to
check if the bar fits in.
-Heat the bar strongly over the Bunsen burner for a couple of minutes. Try to fit it into the slot and hole on the
gauge after being heated.
Observation: the bar does not fit into the slot as well as the hole.
Conclusion: solid (bar) expands when heated.
b) Leave the bar to cool and test again
Observation: The bar once again fits into the gauge (through the slot and the hole)
Conclusion: Solid (bar) contracts when it cools.

Page 52
8.6.2 Thermal Expansion and Contraction IN LIQUIDS
Liquids expand when heated. They expand more than solids because the molecules are not tightly bound together as those
in solids.
8.6.3 Unusual expansion of water

If we start with water that is warmer than 4 °C, as the water cooled to 4 °C it contracts as any liquid would do. But
surprisingly as it is cooled from 4 °C to 0 °C it expands. Water therefore has a minimum volume (and maximum density) at 4
°C.
As the water freezes at 0 °C it expands even more. This is why the water pipes burst in very cold weather.
The unusual expansion of water between 4 °C and 0 °C helps the fish to survive in a frozen pond.

The water at the top cools first, contracts and becomes denser and sinks to the bottom. The less dense water rises to the
surface to be cooled, become denser and then sinks as well. When all the water is 4 °C, the circulation ceases. If the
temperature of the surface water falls below 4 °C the water becomes less dense and remains at the top and eventually
forming a layer of ice of 0 °C. The temperatures in the pond are then as shown above.
*NB:- When water is heated from 0 °C to 4 °C instead of expanding it contracts and also reaches its minimum volume at 4
°C. From 4 °C upwards it expands as we would expected.
8.6.4 Thermal Expansion and Contraction IN GASES
GASES also expand when heated .All gases expand at the same rate unlike solids and liquids. H2 and CO 2,will expand the
same for the same rise inn temperature
8.6.5 Experiment to compare the expansion of water (liquid) and air (gas)
Two identical flasks A and B are filled with water and air. Flasks A and B are at the same time placed into warm water in a
small bowl C.

Page 53
The water level in flask A is seen to rise very slowly but the coloured pellet in flask B rises up the capillary tube rapidly. This
shows that air expands more faster than water.
Roughly the relative order of magnitude of expansion of solids, liquids and gases is 1 : 10 : 100 respectively
Most expansion -------------------------------------------------------------------------> least expansion
Gases liquids solids

8.6.6 APPLICATIONS OF THERMAL EXPANSION IN EVERYDAY LIFE

A). Bimetallic strip – it is a device based on the different expansion of solids. It consists of two metal strips of
equal size but different rates (amount) of expansion, e.g. iron and brass. The strips are riveted or welded
together. On heating, the bimetallic strip bends with brass on the outside of the curve and iron inside. This is
because the brass expands more than iron for the same temperature rise.

Bimetallic strip is used in thermostats to work as electric switch. Thermostats are useful to control
automatically temperature of:

1). Electric iron 4). Refrigerators

2). Electric and gas ovens 5). Fire alarms
3). Waters heaters 6) Bimetallic thermometer, etc.
*NB;- Some of the above appliances have control knobs. When the control knob is screwed down the
strip has to bend to bend more to break the heating circuit and this needs a higher temperature.
B). Riveting metal plates
Rivets are used to join two sheets of metals very tightly. During riveting, holes are bored in the two sheets, then a very hot
rivet is pushed through and hammered strongly on both sides to make head on each end. The heads hold the sheets
together. As the rivets cools, it contracts and this pulls the sheets even more firmly together.
C). Shrink fitting – This is method to fit axles in gear wheel. An axle which is slightly too large to fit into the gear
wheel is cooled in liquid nitrogen. The axle contracts until it can easily fit into the gear wheel. Then when the
axle warms up later, it expands and this produces a very tight fit between the wheel and the axle.
D). Liquid-in-glass thermometer:- mercury or alcohol expand when heated (or contract when cooled). This
fact is used to measure temperature.
E). Hot air balloon:- propane gas expands and becomes lighter when heated. It fills up a balloon which will
then because of the density difference between the propane inside and air outside will rise upwards and fly
around.
8.6.7 EVERYDAY CONSEQUENCES OF THERMAL EXPANSION
1). When railway tracks were laid with the ends of individual rails closely and firmly fixed together with no gaps
between, expansion made the tracks buckle.

Page 54
 To allow for expansion and avoid destruction, gaps are left between the end of one rail and the next.

The rails are tapered at each end, then each end overlaps with the end of the next rail. As the rails expand or
contract their ends slide over one another.

2). Steel bridge

One end of the bridge is supported on the rollers and the other end is fixed. As the bridge expands the end on the rollers
can move slightly, enough to avoid any damage to the bridge.
3). Telephone and power-lines:- are hung slightly slack ( too loose) if they are put up in summer to allow for
safe contraction in winter or at night without pulling the poles down or the wire snapping (breaking). If they
are put up in winter, they are tightened up a bit so that they do not become loose (slack) when they expand
in summer or during the day.
4). Tyre bursting:- more common during very hot days. It is caused by the expansion excessive expansion of
air inside the tyre.
5). Water pipe bursts:- due to expansion of water as it freezes.
6). Creaking noises in the roofs of buildings:- caused when the corrugated iron sheets slide over each other
as they expand or contract.
7). Freezing of water in the car radiators:- car radiator should have anti-freeze added to it to lower the
freezing point of water.
8.6.8 QUESTIONS
1. A student sets up the apparatus as shown below. When the student holds his hands on the flask, air bubbles
flow out from the bottom of the tube. Explain this, mentioning in your answer the behaviour of the air
molecules. When the student removes his hands from the flask, water goes up the tube to a point than it was
before. Explain why this happens.

Page 55
2. The diagram shows electricity cables that have been put up between their poles on a day when the weather
was quite warm

Why do you think the cables have been left slack?

3. Explain why
(a) thick glass vessels often crack if placed in very hot water.
(b) a stubborn screw lid on a jar can often be unscrewed after being warmed in hot water.
(c) a bimetallic strip bends when heated
(d) water pipes likely to burst during a very cold weather

4. The diagram shows a bimetallic strip. Given that brass expands more than iron, draw diagrams to show how
the strip will appear:

(a) if it is heated up (b) if it is cooled down

5. The diagram below shows a thermostat. It contains a bimetallic strip made of brass and steel. When heated,
brass expands more than steel. The bimetallic strip is used to switch the heater off when the temperature
rises above the pre-set value.

(i) When the bimetallic strip is heated the heater is switched off. Explain why.
(ii) How would you use the control knob to make the heater switch off at a higher temperature?
6. The diagram shows a warning system containing a bimetallic strip. The bimetallic strip has two metals X and
Y firmly joined together.

Page 56
 (a) Explain how and why
(i) lamp B lights when the temperature of the strip increases by 20 °C.
(ii) lamp A lights when the temperature falls by 20 °C.
(b) State what effect moving the metal contacts nearer to the bimetallic strip would have on the warning
system.
7. A glass bottle was heated. State whether the following properties were unchanged, decreased or increased.
(a) mass of the bottle
(b) density of the bottle
(c) external diameter of the bottle
(d) volume inside the bottle.

8.7 MEASUREMENT OF TEMPERATURE and THERMOMETERS

8.7.1 Temperature can be defined as the measure of the degree of hotness or coldness of a body.
The S.I unit for temperature is kelvins. The usual unit is degree Celsius with a thermometers.
Thermometers make use of some physical properties that change linearly/uniformly with temperature to make
measurements. These properties could be referred to as thermometric properties.
Examples:
TYPE OF THERMOMETER THERMOMETRIC PROPERTY
Liquid-in-glass thermometer Change of volume of volume (expansion/contraction of liquid)
Thermocouple thermometer Change of electric current/ e.m.f
Platinum resistance thermometer Variation in electrical resistance of platinum wire
Gas-volume thermometer Change in pressure of a gas

8.7.2 Liquid-in-glass thermometer

A. LABORATORY (LAB) THERMOMETER

Main features:-
➢ A thin capillary tube/bore
➢ A bulb with a thin glass wall
➢ A liquid in bulb (alcohol, mercury)
➢ A vacuum above the liquid in the capillary tube
Heat is transferred to the liquid inside bulb by conduction and radiation through the glass wall. After some time the heat will
reach the liquid. The heat is transferred through the liquid by convection. The glass and the liquid will begin to expand. The
liquid rises up the column of the capillary bore because it expands faster than the glass.

Page 57
Thermometric liquid
The liquid should have the following properties:
➢ It should have a linear expansion when heated
➢ It should be a liquid over a wide range of temperatures and expands by large amounts.
➢ It should not wet i.e. should not stick to the glass.
NB: Alcohol should be coloured to make it visible through glass.
Comparing alcohol and mercury as thermometric liquids
1) Alcohol
➢ Its expansion is about six times that of mercury
➢ Has lower freezing point (about -122 °C) so can be used in very cold temperature region.
Disadvantages
➢ Has a lower boiling point (78° C)
➢ Colourless so it always needs to be coloured for it to work as thermometric liquid.
2) Mercury
➢ is opaque so it can easily be seen
➢ does not vaporises easily
➢ conducts heat rapidly
➢ does not wet the glass (does not cling to the walls of the capillary bore)
➢ it has a higher boiling point (375 ° C)
Disadvantages
➢ it has a higher freezing point (-39 ° C) so it is not suitable to measure low temperatures in very cold
regions
➢ poisonous
➢

Calibrating or graduating a thermometer

This is a process of marking a scale on a thermometer. Calibrating a thermometer in degrees Celsius (Celsius scale of
temperature) involves several stages.
(a) First, the lower and upper fixed points must be marked on the scale. Fixed points are standard temperatures of
natural phenomena that can easily be reproduced as a basis for a temperature scale..
(b) . Lower fixed point (or ice point) is defined as the temperature at which pure ice melts at sea level and its value
is taken to be 0 °C.
(c) The upper fixed point (steam point) is the temperature of steam above boiling water at standard atmospheric
pressure of 760 mmHg and is taken to be 100 °C.
(d) Determining the fixed points experimentally - \
(i) LOWER FIXED POINT (L.F.P) -

(ii) UPPER FIXED POINT (U.F.P)

- Place the uncalibrated thermometer in - Next, place the thermometer in the steam
crushed pure melting ice placed in a above boiling water in a flask.
funnel above a beaker. - Allow the mercury thread to rise until it
- The mercury thread falls and eventually stabilises at a particular point. That point
stabilises at one point. That point represents U.F.P.
represents the L.F.P. - Mark against the level of mercury thread
- Mark on the stem against the level of the on the stem and label it 100 °C.
mercury thread and label it 0 °C.

Page 58
(e) Measure the distance between L.F.P and divisions. Each division is equal to 1 °C.
U.F.P and divide the space into 100 equal

NOTE: When using a thermometer without scale marks but only with lower fixed point and upper fixed point
marked, one may use the following equation to find the value of temperature for any given length of the column.

θ = Xθ – X0 / (X100 – X0) x ∆T

where θ – unknown temperature

X0 – length of mercury thread at
0 °C (L.F.P)
X100 – length of mercury thread at
100 °C (U.F.P)
Xθ – length of the mercury thread
at temperature θ (unknown
temp).
∆T = difference between known
temperatures (= 100 °C in the
diagram above)

Page 59
Examples #1.
A student puts the bulb of an unmarked liquid-in-glass thermometer into melting ice, then into steam above boiling water and
finally into sea-water. Each time she waits until the liquid level is steady and then marks the level. The diagram shows the liquid
levels measured from the bulb. What is the temperature of the sea-water?

Data: X0 = 2 cm, Xθ = 4 cm, X100 = 12 cm, θ = temp. of sea-water, ∆T = 100 °C

Θ = Xθ – X0 / (X100 – X0) x ∆T
= 4 – 2/(12 – 2) x 100
= 2/10 x 100
= 20 °C

Example #2.
Find temperature X

Data: X0 = 2 cm, Xθ = 5 cm, X100 = 7 cm, ∆T = 100 °C, θ = X

Θ = Xθ – X0/(X100 – X0) x 100 °C

X = 5 – 2/(7 – 2) x 100
= 3/5 x 100
= 60 °C

Example #3
Find temperature X

Data: X-10 = 2 cm, Xθ = 9 cm, X110 = 14 cm, ∆T = 120 °C, θ = X

Θ = Xθ – X-10/(X110 – X-10) x ∆T
X = 9 – 2/(14 -2) x 120
= 7/12 x 120
= 70 °C

B. CLINICAL THERMOMETER

Page 60
 Clinical thermometer is designed to measure human temperature. It has the following features:-
• Thin-walled glass bulb
• Narrow capillary bore
• Constriction in the capillary just above the bulb
• Short temperature range (35 °C – 42 °C).
• Vacuum above the mercury
EXPLANATION OF PURPOSE OF DIFFERENT FEATURES
➢ A vacuum – allow free movement of the mercury inside the capillary bore.
➢ Glass bulb with thin wall allows heat to pass quickly into the mercury. Even though the glass bulb of a clinical
thermometer is smaller than that of a laboratory thermometer, but in relation to its bore, it is large and this improves its
sensitivity.
➢ Narrow capillary makes the thermometer sensitive to small changes in temperature.
➢ Constriction prevents mercury from falling back into the bulb when removing the thermometer from the body, before a
reading is taken. The mercury above will be trapped and this allows the nurse to take accurate reading from the
thermometer. When the reading is taken the thermometer is shaken/flicked carefully so that mercury moves back into
the bulb.
➢ Short temperature range- this is so because the normal body temperature is 37 °C and does not vary much from this
value. With a few degrees marked on the scale, the distance between unit degrees is greater and this makes the
thermometer very sensitive and easy to read accurately.
➢ Lastly the stem of the clinical thermometer is specially shaped, it has a triangular cross-section. This shape produces a
lens effect which would magnifies the bore and make it more visible for easy reading.
➢ Uses only mercury because it is quick responding since it has a low specific heat capacity and great conductivity.
Question :- Why should we not put a clinical thermometer inside boiling water?
Answer :- Temperature of boiling water is 100 °C but the maximum temperature that can be read by a clinical
thermometer is only 42 °C. So if sterilized in boiling water, the large expansion of mercury will cause the thermometer
to break.

8.7.3 SENSITIVITY, RANGE AND LINEARITY

SENSITIVITY OF A THERMOMETER:- refers to its ability to detect even small changes in temperature. It can also be defined in
terms of the distance between unit degrees marked on the scale. For a very sensitive thermometer, the degrees are far apart
and are close together for less sensitive thermometer. Sensitivity depends on the following:-
➢ Bulb :- if the bulb is small, heat will be distributed quickly throughout the whole liquid and the liquid will expand quickly.
But the bulb needs to be large in relation to the size of the bore for higher sensitivity.

Thermometer A with a large bulb and a narrow bore is more sensitive than thermometer B with a small bulb but wide
bore.
➢ Thickness of the glass wall:- bulb should be made of thin walled glass for heat to easily reach the liquid in the bulb

C D
Thermometer C with a thin glass wall responds quickly because heat passes quickly through the thin glass to the liquid
inside. Thermometer D with a thick glass wall responds slowly because heat passes slowly through the thick glass to
the liquid.

Page 61
 ➢ Width of the bore:- for higher sensitivity the bore of the thermometer should be very thin (narrow) so that a small
expansion of the liquid can result in a larger change in the position of the level of the mercury (length of mercury
thread) inside the thermometer.
Note: Mathematically, sensitivity can be expressed as change in the length of the mercury column per unit temperature
increase.
e.g. If a column of a thermometer increases by 10 mm for every 2 °C increase in temperature, what is the sensitivity of
the thermometer?
Sensitivity = 10 mm/2 °C = 5 mm/°C

RANGE OF A THERMOMETER:- is the temperature interval (value of the lowest temperature and highest temperature) that can
be measured by a thermometer.
e.g. A clinical thermometer; range = 35 °C – 42 °C
A laboratory thermometer; range = -10 °C – 110 °C
The range of the thermometer also depends on the size of the bulb and the width of the bore:- If the bore is small relative to
the size of the bore, the thermometer will be able to measure a wide range of temperature.
The range of a thermometer is also affected by the length of the stem. Thermometers with long stem have large ranges whilst
those with shorter stems have smaller ranges.

Summary of the effects of bulb size and bore width on range and sensitivity
Range Sensitivity
Volume Large low high
of bulb Small high low
Width of Wide high low
bore Narrow Low high

LINEARITY OF TEMPERATURE SCALE

It refers to whether the temperature degree marks are uniformly/equally spaced on the scale.
Linear scale: temperature scale on the thermometer should have equal temperature divisions of equal size/length/spacing
(equal temperature differences equally spaced). This is so because change in temperature is proportional to change in the length
of the liquid column (or any thermometric property).
But for the temperature scale to be linear, the tube must have a uniform diameter.

8.7.4 THERMOCOUPLE THERMOMETER

This is an electrical thermometer. A simple thermocouple is made from three pieces of two kinds of wires with some of their ends
twisted together to form junctions and the free ends connected to a sensitive galvanometer. They wires can be arranged so that
they alternate, e.g. Cu – Ni – Cu or Ni – Cu – Ni

To use the thermometer, one junction X (cold junction) must be put into melting ice. The other junction Y (hot junction) is placed
into the body of substance of which its temperature is to be measured, e.g. warm water. Difference in temperatures at the two

Page 62
junctions induces an e.m.f (voltage) across the junctions which cause the current to flow through the circuit. This will result with a
deflection on the sensitive galvanometer.
Note:
• The deflection is greater when the temperature difference is greater.
• If the temperature of both junctions is the same then no voltage is produced.

Advantages of a thermocouple
i) A thermocouple responds quickly to temperature changes, because metal wires are good conductor
of heat and also only a small part can be put into a substance, it can quickly attain the temperature of
of the substance.
ii) A thermocouple can be used to measure very high and very low temperatures (-200 °C – 1500 °C),
e.g. used to measure high temperature inside blast furnaces and car engines.

8.7.5 ABSOLUTE ZERO AND KELVIN SCALE

When the temperature falls, the kinetic energy of its particles fall as well and move more and more slowly. At lowest temperature
that can be reached by the object the particles have the minimum energy possible. This temperature is known as absolute zero.
And its value is taken to be -273 °C or 0 K.
Absolute Temperature
Absolute temperature is the temperature on the Kelvin scale, in which the temperature is expressed in kelvin (K). One Kelvin (1
K) has the same size as one degree Celsius (1 °C). The Kelvin scale uses absolute zero as its zero (0 K).
The Kelvin and Celsius scales can be connected by the scale
equation below:
#2 Convert a) 50 °C to K
T = θ + 273 b) 100 K to °C

where T = temperature in kelvin ANSW: a) Data: θ = 50 °C, T = ?

(K)
θ = temperature in degree T = θ + 273
Celsius (°C) = 50 + 273
= 323 K

E.G. b) Data: T = 100 K, θ = ?

Absolute Melting Boiling T = θ + 273
zero point water THEN θ = T -273
Celsius -273 °C 0 °C 100 °C = 100 K – 273
scale = 173 °C
Kelvin 0K 273 K 373 K

8.7.6 QUESTIONS
1. The scale on a thermometer used for measuring the temperature includes two fixed points. What are the
values of these?
Explain why the length of the mercury thread changes when the temperature rises?

2. (a) A clinical thermometer, used to measure human body temperature has a constriction just above the
bulb, why is the constriction necessary?
(b) The thermometer temperature is 35 °C – 42 °C, why is the range made to be so small?
(c) How is the thermometer made very sensitive?

3. The diagram shows a laboratory thermometer.

Page 63
 (a)Name the substance labelled A.
(b)Name the section labelled B.
(c)Why is part C of the tube enlarged?
(d)Is the wall of the tube marked D thin or thick? Explain why it is so.
(e)Using a well-labelled diagram, describe how you would check the accuracy of the point marked 0 °C on
the thermometer.
4. (a) Convert these to kelvin (K): i) 27 °C ii) -3 °C iii) 150 °C iv) -90 °C.
(b) Convert these to degrees Celsius (°C): i) 373 K ii) 200 K iii) 1000 K.

5. The scale of a mercury-in-glass thermometer is linear. One such thermometer has a scale extending from
-10 °C to 110 °C. The length of that scale is 240 mm.

(a) What is meant meant by the statement that the scale is linear?
(b) Calculate the distance moved by the end of the mercury thread when the temperature of the
thermometer rises
(i) from 0.0 °C to 1.0 °C
(ii) from 1.0 °C to 100 °C.
6. A mercury thermometer is calibrated by immersing it in turn in melting ice and then boiling water. The
column of the mercury is respectively 2.0 cm and 22.0 cm long. What would be temperature reading when
the column is 7.0 cm long?

MELTING AND BOILING- CHANGE OF STATES.

8.8.1 Whenever a substance undergoes a phase change (boils, melts or condenses, etc) energy is taken away

Page 64
 or added to the substance. But surprisingly there is no temperature change during a phase change.
*Phase – refers to a state in which a substance (matter) can exist.
8.8.2 Melting
Melting is a process in which a substance changes its state from solid to liquid and the reverse process (liquid to solid) is called
freezing or solidification.
When a pure solid melts it stays at the same, definite temperature is called its melting point and it also solidifies at the very
same temperature (now it would be called its freezing point). During melting or freezing, the temperature does not change
even though the substance continues to gain or lose (heat) energy. The energy gained is used to re-arrange the
particles/molecules/atoms of the substance.
The heat absorbed by the substance during melting or given out during solidification is called latent heat of fusion. The
energy is used to overcome the attractive forces between the particles that keep them in their fixed positions. Latent heat
changes the state of the substance without change in the temperature (“latent” literally means hidden)
8.8.2 Boiling
Boiling is a process in which the substance changes state from liquid to gas and the reverse process is called condensation (gas
-----> liquid).
If the energy is supplied to a liquid, e.g. water, its temperature rises until it boils. During boiling the temperature of water remains
constant. The temperature at which a liquid turns into a gas by boiling is called its boiling point. As water turns into steam, the
energy supplied does not cause a rise in temperature instead is used to enable molecules to break the attractive forces holding
the particles together. The energy absorbed and used to change a liquid to a gas without changing the temperature of the
substance is called latent heat of vaporisation. The latent heat of vaporization is given out during condensation to change a gas
to a liquid.
8.8.3 PLOTTING A GRAPH OF TEMPERATURE AGAINST TIME
1) BOILING CURVE
When ice at a temperature below 0 °C, say -10 °C is allowed to warm up slowly, its temperature will rise to 0 °C and remain
constant until all the ice has melted. The temperature will begin to rise up to 100 °C where it remains constant until all the water
has vapourised into steam and the temperature of the steam will rise above 100 °C.

BOILING

2 COOLING CURVE
We can also plot a graph of temperature against time (boiling curve) when the steam of temperature above
100 °C.

Page 65
 condensation

water + ice ice

8.9 Evaporation
8.9.1 It is the process in which a liquid changes into a gas at a temperature below its boiling point. All molecules
do not have the same energy. During evaporation, molecules with greater energy than others and are
nearer to the surface escape into the space above the liquid
*Liquids which evaporate and boil at low temperatures are called volatile liquids.
8.9.2 Factors increasing the rate of evaporation.
a). Temperature of the surrounding
At higher temperature, molecules gain more energy and move faster and time for them to reach the surface decrease. Therefore
a larger number of molecules can escape from the surface.
b). Surface area
If the surface area is large, more molecules will evaporate because more molecules are near the surface and also there is more
room for them to escape.
c). Humidity
When the humidity is high (i.e. water vapour is present in air in greater proportion) the molecules which escaped from the liquid
collide with the water molecules in the atmosphere, so some of the escaped liquid molecules will return into the liquid.
d). Draught (wind) over the surface
If wind blows over the surface of the liquid, the escaped molecules from the surface of the liquid will be rapidly carried away by
the draught and thus reducing the possibility of their return into the liquid.
8.9.3 Cooling by evaporation
During evaporation, the high energy molecules escape from the liquid leaving the low energy molecules behind. Therefore the
average kinetic energy of the remaining molecules decreases. This lowers the temperature of the liquid because the temperature
of a substance is proportional to the average kinetic energy of its molecules.

Page 66
8.9.4 Some applications of evaporation
i). Cooling our bodies- your body sweats in hot weather, as the sweat evaporates it takes in latent heat from
your body and cools it, this helps get rid of excessive internal energy.
ii) In refrigerators and freezers

Refrigerator has sealed system of thin pipes with compressor, a condenser and an evaporator. A volatile liquid (such as Freon or
ammonia) known as refrigerant is pumped through the coiled pipes around the freezer compartment in the top of the refrigerator.
The refrigerant evaporates and takes latent heat from its surroundings, producing cooling inside the refrigerator. A pump is used
to draw the vapour (so reducing its pressure, loweing its boiling point and encouraging further evaporation and removing more
from the refrigerator) and then forces it into the heater exchanger at the rear of the refrigerator. Here the vapour is compressed.
It liquefies, giving out latent heat of vapourisation into the surrounding air. The liquid, now at room temperature, returns to the
coils, returns to the coils in the freezer and the cycle is repeated.
iii). In air conditioners
It works in the same way, but on a larger. The refrigerant liquid evaporates in the coil inside the building and extracts latent heat
from the air in the room, cooling it down. The resulting vapour then condenses under pressure in the coil outside the house
releasing the latent heat to the outside air.

8.9.5 Evaporation and Boiling

During boiling, the average k.e. of particles is high enough for some groups of particles to form separate bubbles of vapour
throughout the liquid, these bubbles will be seen moving rapidly and will burst at the surface during boiling. At the boiling point,
some of the particles near the surface gain enough energy to escape from the liquid. These escaping particles form vapour
above the surface of the liquid. This is evaporation.
Differences and similarities between boiling and evaporation
Both processes involve a change in state from liquid to gas, but evaporation is not the same as boiling.
A). Differences
Boiling Evaporation
1). quick 1). Slow
2). Occurs at only one temperature – boiling point 2). Occurs at all temperatures
3). Occurs throughout the whole body of the liquid 3). Occurs only at the surface
4). Bubbles seen 4). Nothing visible happens (no bubbles)
5). Source of energy is needed 5). Energy supplied by the surroundings
6). Boiling point increases with increase pressure 6). Rate of evaporation decrease with increase in
pressure
7). Decrease with increase in altitude 7). No effects

Page 67
B). Similarities
1). Both form vapour
2). Both take place in liquids
3) Both occur as a result of increase of k.e in the molecules
4) Latent heat of vapourisation is needed for both processes

8.10 QUESTIONS
1. A boy has been swimming in a pool. He comes out of the water onto hot sunshine but he feels cold until he
has dried himself. Why did he feels cold when he was still wet?
2. Table shows the melting points and boiling points of four substances. Which state are the substances in at
room temperature (say 15 °C)?
Substance Melting point / °C Boiling point / °C
A -73 -10
B -39 357
C 17 118
D 29 669

b) For which substance(s) would the state change on a warm day?

3. A large piece of ice is taken from a refrigerator has a temperature of -2 °C. Its temperature is measured as it
is warmed. Sketch a graph to show how its temperature changes with time until the water is boiling.
4. The diagram below is the outline of a heat pump system. A suitable refrigerating liquid or its vapour is
circulated round a loop of pipes. In one part of the loop (the compressor) the vapour condenses into liquid; in
another part (the expansion valve) the liquid evaporates. Explain what transfer of thermal energy (heat)
occurs (i) when a liquid evaporates and (ii) when a liquid condenses.

5. The graph shows how the temperature of a pure substance changes as it is heated.

(a) At what temperature does the substance boil?

(b) On the graph, mark with an X any point where the substance exists as both a liquid and gas at the same
time.
(c) i) All substances consists of particles. What happens to the average kinetic energy of these particles as
the substance changes from a liquid to a gas.
ii) Explain, in terms of particles, why energy must be given to a liquid if it is to change to a gas.

Page 68
6. The graph below shows how the temperature of some liquid in a beaker changed as it was heated until it was
boiling.

(a) What was the boiling point of the liquid?

(b) State and explain what difference, if any, there would be in the final temperature if the liquid was heated
more strongly.
(a) State two differences between boiling and evaporation.
(b)

8.11.1 HEAT CAPACITY

Same amount of heat transferred to different objects does not cause the same temperature change in each of them. Experiments
show that:
i. The temperature change is inversely proportional to the mass of the object which is heated.

ii. The temperature change differs from material to material. For any one material (e.g. water, iron,
mercury, copper, etc.) there exists a different constant, C. The constant C is called heat capacity of an object.

Defintion . Heat capacity, C, is the amount of heat Energy neede to raise the temp. of a substance by 1 °C or 1 K. . SI Unit is
joule per celsius (J/°C or J °C-1) OR joule per kelvin (J/K or J K-1).
From the definition, mathematically heat capacity can be expressed as:-

C = Q/∆T, Q = C∆T ----------------------> (1) joules (J)

Where Q = amount of heat transferred/supplied to the object in

∆T = change in temperature (final temp Tf - initial temp Ti) in °C or K
C = heat capacity in J/°C or J/K
8.11.2 SPECIFIC HEAT CAPACITY
Defintion: The amount of heat needed to raise temperature of a unit mass of a material by 1 °C or 1 K. The SI
unit is joule per kilogram per degree celsius ( J/kg/°C or J kg-1 °C-1 or J/(kg °C)) OR joule per kilogram per kelvin (J kg-
1 -1
K )

Specific heat capacity ( small c) is in fact heat capacity per unit mass, which means that

c = C/m ---------------> (2)

which follows that Q = mc∆T

where Q = amount of heat transferred or supplied in joules (J)

m = mass of the material in kg
c = specific heat capacity of the material in J kg-1 °C-1 or J kg-1 K-1
∆T = change in temperature
Page 69
*Note that the symbol for the specific heat capacity is c, not C. C is the symbol for heat capacity.
∆T = |∆T|, this means ∆T should always be positive even if Tf is less than Ti
MEASURING SPECIFIC HEAT CAPACITY OF METAL BLOCKS

The set up above can be used to measure specific heat capacity. Some oil is placed into the holes to improve
conduction from heater to thermometer. The metal block must be covered by insulating material to prevent heat
loss to the environment. Provided the power of the heater is known, the time for which it is on can be measured
using a stopwatch.
Q = Pt= IVt #2. Calculate the heat required to raise the
Q is energy supplied in (J) temperature of 10 kg of brass from 10 °C to 90 °C.
P is power (w) Specific heat capacity of brass = 377 J kg-1 °C-1.
t is time (s)
I is current (A) Answ:
V is voltage (V) Data:- m = 10 kg, Ti = 10 °C, Tf = 90 °C,
c = 377 J kg-1 °C-1, Q=?
The final temperature reading should be taken after
the heater is switched off allowing time for the heat Q = mc∆T
to be conducted through the block. = 10 x 377 x (90 – 10)
= 301 600 J
𝑃𝑡 𝐼𝑉𝑡 𝑄
Therefore: 𝑐= = =
𝑚∆𝑇 𝑚∆𝑇 𝑚∆𝑇 #3 A kettle containing 1 kg of water (c = 4200 J kg-1
°C-1) is placed on top of an electric heater of power
Problems
1000 W. It takes 5 min for the water temperature to
#1Find the specific heat capacity of the liquid given
rise from 20 °C to 90 °C. Find:
that:
a. the energy released by the heater
i. energy transferred = 12 209 J b. the energy absorbed by the water. Account for
ii. mass of liquid = 0.8 kg any losses in energy
iii. original temperature = 26.8 °C
iv. final temperature = 33.0 °C Answ:
a) Data:- P = 1000 W, t = 5 min = 300
Answ Data: Q = 12209 J, m = 0.8 kg, Ti = s, Q=?
26. 8 °C, Tf = 33.0 °C, c =?
Q = E = Pt
Q = mc∆T = 1000 x 300
c = Q/m∆T = 300 000 J
= 12209/(0.8(33.0 – 26.8)) b) Data:- m = 1 kg, c = 4200 J kg-1 °C-
1, Q = ?
= 301 600 J
Q = mc∆T
= 1 x 4200 x (90 – 20)
= 294 000 J

Page 70
 6000 J of energy are lost to the surroundings #5 In an experiment, 920 000 J of energy is transferred to 2
and cointainer by conduction, convection and kg of iron (c = 460 J kg-1 °C-1). The initial temperature of
radiation. iron is 25 °C. What is the final temperature of the iron?

#4 If 2 kg of water cools from 70 °C to 20 °C, how much Answ:

thermal energy does it lose? Data:- Q = 920 000 J, m = 2 kg, Ti
= 25 °C, c = 460 J kg-1 °C-1
Answ:
DATA:- m = 2 kg, Ti = 70 °C, Tf = 20 °C, c= Q = mc(Tf – Ti)
4200 J kg-1 °C-1, Q =? Tf = (Q/mc) + Ti
Q = mc∆T = 920 000/(2 x 460) + 25
= 2 x 4200 x (70 – 20) = 1000 + 25
= 420 000 J. = 1 025 °C

14 Fig.14.1 shows apparatus used to determine the specific heat capacity of copper.

Fig.14.1

(a) Complete the table by naming and giving the functions of the devices M1, M2, M3.

device name function

M1

M2

M3

[3]
(b) The copper block has a mass of 1.4 kg. The block is heated for 300 s and its temperature increases
from 25 °C to 50 °C.
The specific heat capacity of copper is 390 J/(kg°C).

(i) Calculate
1. the temperature rise of the block,

Page 71
 2. the heat energy that causes this temperature rise.

heat energy = …………………..

(ii) The total energy supplied by the heater in the 300 s is 18 000 J.

Calculate

1. the amount of heat energy lost,

Heat lost= …………………………

2. the rate at which heat energy is lost.

rate of heat loss= ……………………

(iii) Suggest one way of reducing the heat loss from the block.
………………………………………………………………………………….

[7]
15 A student has 1kg of cold water at 20 °C, and some hot water at 40 °C. She wants to make a bath at 35 °C.
Specific heat capacity of water = 4200 J/(kg°C).

(a) What mass of hot water must she add to the cold water?

mass = ………………..[2]

(b) What assumption did you make in your answer to (a)

…………………………………………………………………………………[1]

Page 72
8.11.3 SPECIFIC LATENT HEAT OF VAPORIZATION
The specific latent heat of vaporization LV of a substance is the amount of heat needed to change mass of 1 kg of a liquid to
vapour without change its temperature. It measured in J/kg or J/g

Q = mLV where Q = energy supplied (J)

m = mass of the liquid (kg)
LV = sp. Lat. Heat of vaporization (J/kg)

8.11.4 SPECIFIC LATENT HEAT OF FUSION

It is the amount of heat needed to convert mass of 1 kg of a solid to liquid without temperature change. It is measured in
J/kg or J/g.

Q = mLf where Q = heat supplied (J)

m = mass of the solid (kg)
Lf = sp. Lat. Heat of fusion (J/kg)

8.12 QUESTIONS
1. A heater supplies 42 J of energy every second (its power is then 42 W). It is used to heat some water. The
temperature rises by 5 °C in 100 seconds. What is the heat capacity of the water? A boy says it would take
times as long to raise the temperature to 50 °C. Is he right? Explain ypur answer.

2. A beaker of oil and a beaker of water are heated on the same electric hot plate. The beaker of oil has a
lower thermal capacity than the beaker of water. What can you say about how the temperatures change?

3. The heat capacity of a thermocouple is mall. Give two advantages which result from this.

4. What is meant by the specific heat capacity of a substance?

5. Calculate the energy lost by 2.5 kg of steam at 100 °C when it condenses, cools down to 0 °C and solidifies
at that temperature.
Specific latent heat of steam = 2 260 000 J/kg
Specific latent capacity of water = 4200 J/(kg °C)
Specific latent heat of water = 336 000 J/kg

6. A heater raises the temperature of 1.25 kg of water by 20 °C in 30 seconds. The specific heat capacity of
water is 4200 J/(kg °C). Calculate an approximate value for the power of the heater. Use this value for the
power to calculate M, the mass of water boiled away each second when the temperature reaches 100 °c.
Assume that the specific latent heat of vapourisation of water is 2.26 x 106 J/kg. Explain whether the actual
rate at which water is boiled away is greater than or less than M

7. Explain why a drink is cooled more by ice than by the same mass of water at 0 °C.

8. It takes 80 000 J of heat to raise the temperature of 500 g of porridge from 20 °C to 50 °C. Calculate the
specific heat capacity of porridge.

9. An experiment was conducted to measure the specific latent of fusion. Ice was placed in a funnel and
heated for a fixed time. The water from the melted ice was collected in a beaker as shown in the diagram.
The mass of the empty beaker was 50 g.
A 100 W heater was used to heat the ice for 2 min. After the jeater was switched off the mass of the
beaker and the melted ice was 83 g. Use the results to calculate a value for L f, the specific latent heat of
fusion of ice. Explain why your answer is different from the accepted value of 340 J g-1.

Page 73
 8.13 HEAT TRANSFER/ TRANSFER OF THERMAL ENERGY
8.13.1 Heat/thermal energy is always transferred from place at a high temperature to place at a lower
temperature.

There are three common methods or ways by which heat can be transferred, viz:-
(i) Thermal conduction
(ii) Convection
(iii) Thermal radiation

8.13.2 Conduction
This is flow of heat through a substance from places of higher temperature to those of lower temperature without any
movement/flow of the substance (matter) as a whole. It is a main method of heat transfer in solids and heat can be
conducted in all directions.
NB: Conduction can take place in all the three states of matter but at different rates.

1. Molecular explanation of conduction in a solid

When one end of a metal rod is heated, the particles (atoms/molecules) in portion nearest to the source of heat, gain more
kinetic energy and start to vibrate faster and more vigorously. These atoms collide with the neighbours and pass on some of
their energy during those collisions. The neighbours will also begin to vibrate faster and will in turn transmit the energy to the
surrounding atoms. The chain process continues until all the particles are affected and the whole substance is heated even
the farthest parts.

2. Good and bad thermal conductors

Most solids are good conductors of heat. Liquids and gases are bad conductors. Bad conductors of heat are called thermal
insulators.

Experiment #1: To demonstrate that different metals conduct heat at different rates

Page 74
Procedure:
i) Stick a pin to each piece of metal with candle wax
ii) Pour boiling water into the pan.
Note: In the experiment the following should be done
i) Length of all the metal rods should be the same
ii) All the metal rods have the same thickness (cross-sectional area)
iii) Pins attached at the ends of the metal rods should be identical and have equal weights
iv) Metals should be placed into the hot water to same length to ensure equal distribution of heat to all
the metals.
Observation:
The pin attached to the copper falls off first followed by that attached to the aluminium, then zinc and lastly iron.

Conclusion: copper conducts heat fastest and iron slowest.

All four metals can be listed in order of the rate of conduction as follows:- copper, aluminium, zinc, iron.

Experiment #2: To show that wood is a poor conductor of heat.

Apparatus are arranged as follows

Observation
When the rod is passed through the flame several times, paper over the wood scorches (burns) but not that over brass.
Explanation: The brass conducts heat away from the paper very quickly, and prevents it from reaching the temperature at
which it can burn. But the wood conducts heat away slowly and hence more heat builds on the paper, enough to make it
burn.

Note: Metal objects below body temperature feel colder to touch than those made of non-metals because metals conduct
heat away from the hand faster.

Experiment #3: To show that liquids are poor conductors of heat.

Page 75
Procedure:
i) Wrap an ice cube in a metal gauge and place it at the bottom of a boiling tube filled with water.
ii) Heat the water at the top using a low Bunsen flame.

Observation: The water starts to boil at the top before all the ice at the bottom has liquefied (melted).
Reason: Heat is slowly conducted from the top of the boiling tube to the bottom of the tube. Therefore the ice melts very
slowly. This shows that water is a poor conductor of heat.
Note:
i) Metals are good conductors of heat because they have a large number of free moving electrons.
As the electrons travel over the piece of metal, they take some heat with them. So in metals heat is
transferred by electrons and also by the vibrations of the atoms.
ii) On the other hand insulators conduct heat slowly because they have very few free moving electrons
and also their particles are less closely packed together and so they collide less frequently.
iii) Conduction of heat requires a medium and hence it cannot take place in a vacuum (therefore this
means a vacuum is the best insulator/worst thermal conductor)

3. Applications of conduction – uses of good and bad conductors.

Good conductors of heat are mostly metals. They are used where heat needs to be transferred very quickly. Good
conductors (metals) are often used to make:-
i) Bases of cooking utensils (kettles, saucepans, pots, etc)
ii) Base of laundry irons
iii) Bits of soldering irons
iv) Branding irons
v) Dehorning irons, etc.

Poor conductors of heat are mostly non-metals (e.g. air, wood, glass, water, etc). They are used where heat is to be
insulated. Poor conductors are used to make:-
i) The handles of cooking utensils, soldering, soldering iron, laundry iron and many other heating
appliances
ii) Clothes – cloth is made up of fibres. The fibres trap small pockets of air. The trapped air helps to
reduce heat loss by conduction.
b). Other materials which trap air like fur, polystyrene, fibre glass, foam/sponge are used for lagging to insulate
water pipes, hot water cylinders, oven, refrigerators and also used in house roof insulation and cavity wall
insulation to prevent or reduce the rate of heat flow in our house. And air trapped between two window
panes is used in double glazing insulation method in our homes.

8.13.3 Convection

It is the transfer of heat through fluids (liquids and gases) by the upward movement of warmer, less dense parts of fluid. This
movement is actually caused by the difference in densities in different parts of the fluid.
When a fluid, (e.g. water or air) is heated, it expands and becomes less dense than the colder surrounding fluid. Therefore it
floats or rises upwards and is replaced by colder dense fluid which sinks down to take its place. That fluid will be heated too
and in turn rises upwards. At the top, the warm fluid cools, becomes denser and begins to sink down where it will be re-
heated and rises again. Thus, a circulating movement sets up in the liquid until the whole fluid is at the same temperature.
These circulating parts of the fluid are called convection currents.

Page 76
*Convection can also be used to cool a substance. When fluid is cooled, molecules contracts and becomes denser.
The cool, dense fluid sinks and is replaced by warmer fluid which will be cooled and sinks as well. And this
produces convection currents which cool the liquid.

Experiment #1: To demonstrate convection in liquids.

The two sets of apparatus can be used

Observation
Purplish stream of water is seen rising upwards to the top. At the top the stream changes its direction of motion and now
sinks to the bottom.
*This movement is represented by the arrows drawn on the diagrams above. The arrows also show the direction of
the convection current.
Discussion
The liquid nearest to the heat source expands. This lessens its density. The less dense liquid floats and rises up. More
dense, cold liquid moves in to take its place.

Experiment #2: To show convection in air

The arrows on the diagram show the direction followed by the smoke.
Explanation:
The air around the candle flame becomes hot and expands. It becomes less dense and rises. Cool, denser air moves over
to the candle to take the place of the air that has risen up. This causes cool air from outside to enter the box carrying the
smoke with it.

Application of convection

a. Water heating system (geyser)

Page 77
 - The cold water comes into the system at the bottom and is heated by the heat element
- Water expands, becomes less dense and rises up
- It is replaced by more cold water to heated and the convection current is set to heat all the water in the tank.
- The hot water pipe is near the top because hot water would always be at the top.
- If the water cools whilst at the top, it sinks to the bottom to be heated again.
- Overflow pipe is included to prevent build-up of vapour which will increase pressure inside the tank and
cause some explosions or cause some airlocks inside the water pipes.

b. The car cooling system

The arrows on the diagram show the flow of the water

- The petrol burns in the engine cylinders.
- Water surrounding the engine cylinders becomes hot.
- Hot water rises to the top of the radiator by convection
- Heat is passed from the water to the copper radiator by conduction.
- Heat is passed to the air from the radiator by conduction, convection and radiation.
- The cool water flows from the lower end of the radiator back into the engine and the whole re-start and thus
the convection currents are set.
c. In electrical kettles, heating elements are placed at the bottom to allow for all the water to be heated by
convection or convection currents. Also to allow for a radiator or heater to warm up a house by convection, it
should be placed very low near the floor.
d. But when an air conditioner is installed, it is placed up near to the roof so that when convection currents are set
would move down and cool the entire house and the same principle is used in refrigerators so that its inside could
be cooled by convection currents.

8.13.4 Radiation

This is a way of transferring heat in form of invisible heat waves. This is how heat travels from the sun to the Earth.
The heat waves (radiant heat) are called infrared radiation (E.M WAVES)
Note:
• Heat can be transferred by radiation through a vacuum or a transparent medium
• All objects give out some infrared radiation and the hot objects give out more radiation compare to cool
ones.
• Warm or hot objects (at higher temperature than the surrounding) will emit the radiation whereas cool
objects (at lower temperature) will usually absorb the radiation from the surrounding.
Experiment #1: Investigating good and bad absorbers of radiant energy (infrared)

Page 78
 - The apparatus are set up as shown above with a pin attached to back each of the above two objects
(one with dark/black surface and the other with bright/shiny/silver surface). The candle should be
equidistant from both objects for equal radiation to either object.
Observation:
The pin attached to the dark surface fall off first showing that the dark or black surface absorbs radiant heat
from the candle more quickly than the bright surface.
Conclusion: Dark surfaces are good absorbers of radiation whilst bright (shiny, white or silvery) surfaces are
bad absorbers.
In fact the dull black surface is the best absorber while a white or silvery polished surface is the worst
absorber because it is a good reflector of radiation.

Experiment #2: Investigating good and bad emitters of radiant heat.

- The two flasks in the diagram above with boiling water are allowed to cool.
- It is observed that temperature falls more rapidly for the thermometer in the flask with a dark (black)
surface and slower for the thermometer in a flask with a bright/shiny surface.
- This shows that blackened surface loses heat more quickly than the silvered or shiny one.
Conclusion: dark colours emit radiant heat more quickly than bright colours, i.e. dark surfaces are good emitters
of radiant heat whereas bright surface a bad emitters. The best emitter is a dull black surface while a silvery
polished surface is the worst. However, all surfaces emit more radiation as they get hotter.
*NB: Dark surfaces are both good absorbers and bad emitters of radiation. Generally good absorbers are also
good emitters whereas bad absorbers are bad emitters as well.

Applications of thermal Radiation

- Pots and kettles have shiny outer surfaces to prevent them from emitting radiant heat quickly and make
their contents cold.
- Houses in hot climates and petroleum tankers are often painted with bright paint to reduce absorption of
radiant. For the same reason white (or bright coloured) clothes are cooler to wear in summer because
they reflect much of the heat and dark coloured or black clothes are ideal for cold weather to keep you
warm.
- Curved surfaces on electric are made of shiny metal to reflect heat
- The cooling fins on the back of a refrigerator are black so that they lose heat more readily
- Marathon runners, at the end of a race, wrap themselves in shiny blankets to prevent them from cooling
down too quickly.
- The surface of a black bitumen road gets far hotter on a sunny day than the surface of a white concrete
one.

8.13.5 SOME CONSEQUENCES OF HEAT TRANSFER IN NATURE

1. Land and Sea Breezes

Page 79
 Diagram 1 Diagram 2
During a daytime the land gets hotter than the sea. The warm air rises upwards and is replaced by cool air
that blows from the sea towards the land. This sets up some convection currents known as Sea Breezes
(diagram 1).
But, at night the land loses heat faster than sea. Now the warmer air over the sea rises and then is replaced
by cool air that blows from the land to the sea and sets up convection currents that will be called Land
Breezes (diagram 2).
2. Cyclones
- Usually air above warm parts of sea will be warmed as well.
- The warm air rises up carrying moisture high into the atmosphere.
- The rotation of Earth causes the airflow to spin.
- This huge spinning mass of moist air is called a cyclone.
- The cyclone causes wet cloudy weather with strong winds.
- If the winds become very strong (120 – 130 km/h) the storm is called a hurricane or a typhoon.
3. Greenhouse Effects
The Earth’s atmosphere contains a small amount of carbon dioxide gas. This has similar effect to the glass in a
greenhouse (read more on this), it allows short wavelength infrared from the Sun to pass through and get
absorbed by the Earth. The Earth becomes warm and now radiates long wavelength infrared radiation. This
radiation is absorbed by carbon dioxide and water vapour in the atmosphere and causes the atmosphere to
become warmer. The atmosphere reflects some of the energy back to the Earth. This process is called
greenhouse effect and it helps to keep the Earth warmer.
But extra carbon dioxide in the atmosphere as a result of burning of fossil fuels may add to this effect and lead to
global warming.

4. Global warming
It results in the temperature of the atmosphere and sea (Earth). That increased temperature causes melting of the
polar ice-caps. This melting results in the rise of the seal level leading to flooding of coastal areas. Global warming
can also lead to some changes in the Earth climate which will cause the disappearance of some species of plants
and animals.

5. Days and nights in a desert and desert Breezes

During the day the bare land in the desert absorbs much more heat. Therefore the desert sand becomes
hotter than areas covered by vegetation. Then the wind (breeze) blows from the forest (area covered by the
vegetation) to the desert.
But in nights in a desert are very cold because at night the desert loses heat faster. The warmer air rises from
the forest and a breeze develops from desert to the forest.

8.13.6 A VACUUM (THERMOS) FLASK

Page 80
It is designed to keep liquids hot or cold by reducing heat transfer to or from the liquid by the aid of the following features:
Feature of flask Reduces transfer of heat by ........... Explanation
Silvered inner and outer walls radiation Silvered surfaces are bad absorbers
and emitters of radiated heat
Vacuum between walls Conduction and convection Conduction and convection cannot
occur through a vacuum
Stopper or lid Convection and evaporation The stopper traps a layer of air above
the liquid, preventing convection and
evaporation
Glass walls conduction Glass is a poor conductor of heat

8.13.7 SOLAR HEATING SYSTEM

It has the following features:

(i) a solar panel containing a coiled copper tube/pipe and blackened layer on the background. Copper is used
because is a good conductor of heat and also it does not corrode. The tube is coiled to increase the surface
area to increase amount heat absorption. The black surface increases amount of radiation energy
absorbed from the sun as a black colour is a good absorber.
(ii) a glass cover – to trap the radiation energy within the panel.
(iii) the pipe carrying heated water from the panel enters at the top of the storage tank. This allows
the heated water to circulate in the tank by convection.
8.13.8 QUESTIONS
1. The metal rod has one end placed in a fire. Explain how heat gradually travels along the rod to a
person’s hand at the other hand at the other end.
2. Why does the door handle feel colder than the wooden door in a cold weather?

Page 81
3. The rods A and B are the same thickness but made of different metals. They are coated with wax and fixed with their
ends through the wall of a can. Hot water is poured into the can, and after a short time it is found that the wax has melted as
far as Y on rod B but only as far as X on rod A. Explain why the wax melts further along B than along A.

4. Heat energy can be transferred from one place to another by the three processes; conduction, convection and radiation.
(a). Which one of these processes is used to transfer energy by means of the infra-red part of the electromagnetic
spectrum?
(b). Which two processes cannot occur in a vacuum?
(c). Which two processes can occur in a solid?
(d). Which process can only occur in a liquid or in a gas?
5. In a double-glazed window, two panes of glass are separated by a few centimetres . Why does this reduce the heat loss
through the window?
6. Why are loosely knitted clothes likely to keep a person warmer during the cold months?
7. Explain how heat energy is transferred through a container of soup cooking on an electric stove. When the soup has
heated sufficiently, the stove is switched off and the soup cools. Explain how the soup loses heat.
8. A person seating on a beach on a hot sumer’s day is feels a cool breeze blowing from the water (sea breeze).
(a) Explain why there is a sea breeze.
(b) Late at night the same person feels a breeze blowing in the opposite direction (from land to the sea). Explain why the
direction of the breeze often reverses late at night.

9.0 WAVE MOTION

9.1 General wave properties
A wave is any periodic disturbance through a medium which transfers energy from one point to another without the transfer
of matter.
• A wave can be created along a rope by fixing one end and flicking the other end up and down. The humps and
hollows (pulses) which travel along the rope form a wave.

• A wave can also be created along a slinky spring by fixing one end and moving the other back and forth. The
compressions (regions where the coils are close together) and rarefactions (where the coils are further apart)
which travel along the spring form waves.

Page 82
DEFINATION OF TERMS FOR A PROGRESSIVE WAVE

Amplitude (a): height of the crest or the depth of the trough from the undisturbed position of the medium. SI unit is a metre
(m).
Period (T): time taken to produce one complete wave or cycle. SI unit: second (s).
Period = total time taken/no. of complete waves (cycles).
Frequency (f): number of complete waves generated in one second. Its SI unit is hertz (Hz). If a source vibrates such that it
produces 2 waves in one second, we say that its frequency is 2 waves per second which is 2 Hz. The frequency of wave is
the same as that of the source.

Frequency = no. of complete waves (cycles)/total time taken

Then note that: F = 1/T or T = 1/f
Which means 1 Hz = 1/s
Wavelength (λ): the distance between any two successive crests or troughs. SI unit is a metre (m).
Wave speed/velocity (v): distance travelled by the crest or any point on the wave in one second.

Wave fronts: lines joining points on different waves produced by same source at the same time OR lines drawn to
represent the positions of the crests on a wave.
• A circular wavefronts are used to represent circular waves (ripples) and are concentric. Circular waves can be
produced by a single point source(e.g. a finger or vibrating dipper in a ripple tank)

• Straight wavefronts are used for straight water waves and are parallel. Straight waves can be produced using a
vibrating bar or a ruler.

Page 83
*wavefronts are always perpendicular to the direction of the wave travel.

WAVE EQUATION
v = fλ
where v = wave speed in m/s
f = frequency in Hz
λ = wavelength in metres
PROBLEMS
#1 The speed of sound wave in air is 330 m/s. What is wavelength of a sound wave of frequency 170 Hz?
Data : v = 330 m/s, f = 170 Hz, λ = ? λ = v/f
v = fλ = 330 m s-1/170 Hz = 1.94 m
#2 Determine the speed of a wave with a frequency of 1.0 kHz and wavelength of 0.2 m?
Data: f =1.0 kHz = 1000 Hz, λ = 0.2 m, v= ?
v = fλ
= 1000 Hz x 0.2 m
= 200 m/s
9.2 WAVE GRAPHS
There are two ways of representing waves; plotting
• a displacement- distance graph
• a displacement- time graph
displacement- distance graph

wavelength = 2.0 cm
amplitude = 5.0 cm
In a displacement – distance graph, one complete cycle represent one wavelength.

Displacement – time graph

This graph can be used to find the period (T) of a wave. One complete cycle represent the period (T).
Period T = 2.0 s
Frequency f = 1/2.0 s =0.5 Hz
Amplitude a = 3.0 cm.
9.3 TYPES OF WAVES
Page 84
 • transverse wave
• longitudinal wave
Transverse wave: a wave in which the displacement or vibrations of the particles are perpendicular to the direction of the
wave travel.

Examples of transverse
- waves on a spring or string
- water waves
- all electromagnetic waves (radio waves, infrared, light, ultraviolet, x-ray, gamma rays)
-
Longitudinal wave: a wave in which the displacement particles is parallel to the direction of the wave travel (in the same
direction as the direction of the wave travel).

Compression| : The points along the wave, where the particles vibrate towards one another and the air pressure is higher
than normal Atmospheric pressure
Rarefaction : The points along a wave, where the particle vibrate away from each other, and the air pressure is lower than
normal Atmospheric pressure.

Page 85
Wavelength is equal to the distance from the centre of one compression (or rarefaction) to the centre of the next.
Examples of longitudinal waves
- waves on the slinky springs
- sound waves

9.4 REFLECTION AND REFRACTION OF WAVES

Reflection: waves can undergo reflection when they meet an obstacle (barrier).
This can be shown using a ripple tank (to demonstrate reflection of water waves)
- A flat/plane surface is placed a short distance from a vibrator. Waves are then produced. The straight wavefronts
are reflected from the boundary as shown below

The angle at which wavefronts bounce off the barrier is equal to the angle at which they meet the surface
The angle of incidence = the angle of reflection
Circular wavefronts are reflected as shown below. Notice that the reflected waves seem to be coming from an imaginary
source behind the boundary and the reflected waves are the mirror image of the incident waves.
The distance from the real source to the barrier is the same as from the imaginary source to the barrier.

Page 86
 Refraction: if a small glass is placed in the centre of ripple tank the depth of the water here is reduced. As the water
waves enter this region we can see that the wavelength changes because the speed changes but the frequency
remains the same. The wavelength will increase when the wave enters the deeper water again indicating that the
speed has increased.

The ratio of the speed (velocity) v1 of waves in deep water to the speed v2 water in shallow water is known as refractive
index.
Notice that if the boundary between shallow and deep water is at an angle to the direction in which water waves are moving,
the direction of the wave of travel will change. The wave is said to have been refracted or undergone refraction.
The waves bend towards the normal as they enter shallow water and are slowed down. They bend away from the normal as
they leave shallow water and enter deep water.

Page 87
 10.0 REFLECTION OF LIGHT
10.1 Definition
Light travels in a straight line but when it encounters a medium (obstacle) it can be reflected, refracted or absorbed.
When light rays strike shiny surface they will bounce back. This is known as Reflection of light. The ray that moves
towards the surface is the incident ray while the one that bounces back is called the reflected ray.

The following experiments can be performed to show the reflection of light.

#1) Ray method: light ray is sent towards a plane mirror from a ray box. Mark the incident ray and the position of the
mirror. Trace the reflected ray. A normal is drawn and the angle of incident i and the angle of reflection r are measured.
#2) Pin method:
- place a plane mirror on a sheet of plain paper and mark its position.
- Insert two pins P1 and P2 in a line, at an angle to the mirror to represent the incident ray.
- Look through the mirror and place two other pins P3 and P4 such that they are in line with the images of P1 and P2.
- Remove the mirror and pins
- Join pin holes of P1 and P2 to produce an incident ray and those of P3 and P4 to trace a reflected ray. Draw the
normal and measure the angle of incidence and angle of reflection.

Both experiments can be repeated using different values of i including i = 0 (where the incident ray is along the
normal).
Laws of reflection
1. The incident ray, normal and reflected ray all lie on the same plane (so they can be shown on the same flat sheet
of paper)
2. The angle of incidence i is equal to the angle of reflection r (i = r)
3. A ray along the normal (where i = 0) will be reflected along its own path, i.e. back along the normal.

10.2 FORMATION OF IMAGES BY PLANE MIRRORS

One application of reflection is in locating the images formed by/on mirrors. When an object is placed in front of a plane
mirror, incident rays from the object to the mirror can be drawn. The reflected rays are also drawn and are extended
backwards to locate the image position. The image will be formed where the imaginary rays meet.

Page 88
CHARACTERISTICS OF THE IMAGE
The image formed is: • Literally inverted
• Virtual (cannot be formed on the screen) • Same distance behind the mirror as the object
• Same size as the object is in front of the mirror
• Upright/erect
The image formed will be along the same axis with the object. Therefore a line drawn joining to the object should cut the
mirror at the right angle.
10.3 CURVED/SPHERICAL MIRRORS
Two types: - Convex mirror
- Concave mirror

i) CONCAVE MIRROR
It curves inwards; the reflecting surface is inside

i) CONVEX MIRROR
It curves outwards When parallel rays strike a convex
mirror, the rays are reflected such that they
When parallel rays (beam) of light strike a concave diverge/spread out. If the reflected rays are extended
mirror, the rays are reflected (with i = r) such that they backwards, they cross at focus behind the mirror. This
converge to cross at the point called a focus. If the point principal focus behind the mirror is said to be virtual
is on the principal axis is called the principal focus (F). because they rays do not actually originate from or pass
through the point, they only appear to diverge from or
pass through the point. (But for the concave mirror the
principal focus is said to be real because the rays
actually pass through the point).
Definition of terms
Centre of curvature C: is the centre of the sphere of which the mirror appears to be part of. It is in front of a concave mirror
and behind for a convex mirror.
Radius of curvature r: the distance from the centre of curvature to the pole P (centre of the mirror)
Principal axis: is the line joining the pole P to the centre of curvature C
Focal length f: is the distance from the principal focus to the centre of the mirror P (distance FP in the diagram above).
Focal length = half the radius of curvature f = r/2

Following rays are needed to locate the images formed by curved mirrors
i). A ray parallel to the principal axis is reflected through the principal focus.
ii). A ray through the centre of curvature strikes the mirror normally and is reflected back along its own path (NB: radius of
curvature is perpendicular to the surface where it meets the mirror).
iii). A ray through the principal focus is reflected parallel to the principal axis.
10.4 USES OF MIRRORS
a) Plane mirrors
Besides everyday use in our homes to look at oneself when dressing, doing make-ups or seeing through awkward angles,
plane mirror have other uses in a laboratory, e.g.

Page 89
 - Used to help to reduce parallax errors when reading pointer instruments.
- Used in making simple optical instruments e.g. a periscope
A SIMPLE PERISCOPE

Periscope can be used to see over the top of an obstacle which otherwise blocks the direct view.
b) Curved mirrors
- concave mirrors are used as reflectors in headlamps of vehicles, hand torches, searchlights, etc. Reflected
rays from these parabolic (curved) surfaces can travel long distances without becoming weak. But the bulb
should be at the principal focus F of the mirror.
- Concave mirror can be used by a dentist to see teeth inside the mouth and can also be used when shaving
and doing make-ups.
- Convex mirrors can be used as security mirrors in shops
- Convex mirror also used as rear view mirror in vehicles because they give wide field of view.

1.0 REFRACTION OF LIGHT

11.1 DEFINITION
The bending of light as it passes from one transparent medium to another (of different optical density). When a light ray
moves from one medium/material to the other one (of different optical density), its speed changes (as well as the
wavelength) and this cause a change in its direction of travel.

O – point of incidence OB – refracted ray

i – angle of incidence( Angle between
NN’ – normal (line) incident ray and Normal)
r – angle of refraction ( Angle between
AO – incident ray refracted ray and the NORMAL)
Some of examples of effects of refraction in everyday life
1) A stick appears bent or broken at the interface when partly immersed in water.

Page 90
 2) Landscape shimmers on a hot summer day.
3) If you look into a swimming pool it appears to be shallower than it really is.
SOME FACTS ABOUT REFRACTION
1) A ray moving from a less (optically) dense medium to a more (optically) medium ( e.g. air to glass) will bend
towards the normal.

2) A ray moving from a more dense medium to a less dense medium will bend away from the normal.

3) The ray along the normal is not refracted (i = r=0)

Experiments: To show refraction of light

Experiment #1: RAY METHOD
• Place a glass block above a plain sheet of paper and trace its outline.
• Direct a thin ray of light from the ray box towards the glass block.
• Trace the incident and emergent rays onto the plain paper.
• Remove the glass block and trace the refracted ray by joining the incident ray to the emergent ray where they
enter and leave the glass block.

Light refraction through:

a) a rectangular glass block

Page 91
b) semi-circular glass block

c) glass prism

Experiment #2: PIN METHOD

Apparatus: glass block, four optical pins, soft board, protractor, few sheets of A4 plain paper

PROCEDURE:
• Place the glass block on the sheet of plain paper and draw its outline. Remove the glass block.
• Draw a normal at point O.
• Using a protractor draw a line AO such that the angle AON (i = angle of incidence) = 30°
• Place two pins P1 and P2 on the line AO.
• Replace the glass block onto the outline and view images of the pins P1 and P2 from the side BC. Then place two
others pins P3 and P4 such that they are in line with images of P1 and P2.
• Remove the glass block and join the pins P3 and P4 to meet the line BC at point D.
• Join O and D to make line OD and measure the angle MOD (r = angle of refraction).
• Calculate sini and sinr.
• Repeat the experiment for values of i = 40°, 50°, 60° and 70°.
• Plot a graph of sini against sinr and determine the refractive index of the glass by finding the gradient of the graph
line.

Page 92
11.2 REFRACTIVE INDEX (n) AND SNELL’S LAW
Experiments show that:
- when the angle of incidence i increases so does the angle of refraction r but the two are not directly proportional to each
other.
- the graph of sini against sinr is a straight line passing through the origin indicating that for any light ray passing from one
medium to another, the sine of angle of incidence is proportional to sine of angle of refraction.
i.e. sini α sinr
which follows that:
sini/sinr = a constant

sini/sinr = n
-----------------------------> Snell’s Law
Where n is proportionality constant called the refractive index of the second medium with respect to the first medium (or
specific boundary between two media but when the first medium is air it is just called refractive index of the second
medium). The refractive index of a boundary can be simply defined as the ratio of the sine of the angle of incidence to the
sine of the angle of refraction for any ray that it refracts. It indicates the extent to which the second medium will bend the
light. In the graph of sini against sinr, refractive index is represented by the gradient of the graph.
Snell’s law states that:
“The ratio of the sine of angle of incidence to the sine of angle of refraction for a given pair of
media is a constant”
*NB: Refractive index can also de defined as the ratio of the speed of light in a vacuum to the speed of light in a medium.
n = speed of light in a vacuum/speed of light in a medium
3.3 LAWS OF REFRACTION
1. The incident ray, refracted ray and the normal all lie in the same plane
2. Snell’s law: the ratio of sine of angle of incidence to the sine of angle of refraction for a given pair of media is a
constant.

11.4 APPARENT AND REAL DEPTH

When light moves from water to air, it will bend away from the normal. Due to the refraction of light, an object at the bottom
of the pool of clean water (or just the bottom of the pool) will appear closer to the surface, i.e. the light rays from the object
will appear to be coming from a point much closer to the surface. The depth which the object appears to be is called the
APPARENT DEPTH while the actual depth of the pool is called the REAL DEPTH.

The ratio of the real depth to the apparent depth is equal to the refractive index n of water
n = Real depth/Apparent depth

11.5 TOTAL INTERNAL REFLECTION AND CRITICAL ANGLE

When light strikes a transparent material, both reflection and refraction take place. When light ray moves from a more dense
medium like glass to a less dense medium like air, it will bend away from the normal. This makes the angle of refraction r
greater than angle of incidence i. When i increases so does r. r will eventually be equal to 90°. The angle of incidence for
which angle of refraction is 90° is known as the critical angle (ic)

Page 93
 (a) (b) (c)

a) When angle of incidence i is less than the critical angle (i < ic) the ray is refracted and there is also little
reflection at the surface.

b) When angle of incidence is equal to the critical angle ( i = ic) both reflection and refraction take place with
the refracted ray running along the surface of the denser materials (glass), which means r = 90°.

c) When the angle of incidence is greater than the critical angle ( i > ic) the ray is wholly/totally reflected into the
glass. No refracted ray is observed. When this happens, it is said that the light (ray) has undergone TOTAL
INTERNAL REFLECTION (T.I.R)
*NB:- To find the critical;
Sinic = 1/n

TOTAL INTERNAL REFLECTION IN PRISMS

Total internal reflection will occur in glass prism if the angle of incidence is greater than the critical angle of glass which is
about 42°

A right angled glass can be used as shown in (a) above to turn light thru 180° in a rear reflectors in bicycles or cars as well
as in cats eyes (roadside reflectors).

Page 94
Two right angled prisms can be used to turn light through 90° in a periscope.

• T.I.R also helps in focusing distant objects using a pair of a binoculars.

OPTICAL FIBRES
These are thin, flexible rods of glass (or transparent plastic). When light ray is shone into the fibre it bounces from one edge
(side) of the optical fibre to the other by total internal reflection. Light can be transported over large distance with very little
loss of light intensity.

Page 95
USES OF OPTICAL FIBRE
a) Telecommunications:
Nowadays, telephone signals (messages) can be transmitted from one telephone to another by sending light signals through
optical fibres instead of using electricity carried through copper cables. Telephone systems that use optical fibres instead
cables are more efficient and much faster.
b) Endoscope
Doctors can see inside patients’ bodies using optical fibres in an instrument called an endoscope. A very small camera is
attached to one end of an optical fibre. This end is pushed down the throat and into the stomach. The other end is attached
to a television near to the patient. The doctor can see pictures of the inside of the stomach on the television screen.
MIRAGE

It is an optical illusion which results when air near ground or road surface is much warmer than the one high up. It is caused
by the progressive refraction of the light ray from sky as it passes through different layers of air. Near the road surface, the
light ray will meet the warmer air at an angle greater than the critical angle and suffers total internal reflection. The reflection
of light produces an image of the sky which will appear as pool of water on the road to an observer driving along the road.

11.6 QUESTIONS
10.5 QUESTIONS
1. For each of the following cases find the angle of incidence and the angle of reflection

Page 96
2. A ray of light strikes a mirror surface with angle of incidence of 60°. Draw a diagram to show the reflected ray plus the
normal to the surface. If the angle of incidence was 0°, what would the angle of reflection be?

3. On the diagram below, draw two rays to locate the image of the object seen by the observer.

1) Use a diagram to explain why a drinking straw appears bent when partially immersed in a glass of water.
2) A pond of water of water (n = 1.33) is 2 m deep. What is the apparent depth of the pond when a person looks
vertically downwards from above?
3) State two necessary conditions for light to be totally internally reflected.
4) If the refractive index of water is 1.33, how deep will a pond really be if it appears to be 6 m when looking vertically
downwards?
5) Draw a ray diagram to show how a right-angled prism can be used to turn a light ray through: (a) 90°
(b) 180°
6) Draw a diagram to show how two right-angled prisms can be used, in place of two mirrors, in a periscope. Show
the path of the light rays as accurately as you can.
7) What advantages do optical fibre cables have over copper cables in communication systems?
8) The diagram shows rays of light in semi-circular glass block.
a) Explain why the ray entering the glass at A is not bent
b) Explain why the ray AB is reflected at B and not refracted.
c) Ray CB does not stop at B. Copy the diagram and draw its approximate path after it leaves B.

12) Copy the diagrams below and complete the paths of the rays.

Page 97
13). A ray of light is directed at a rectangular glass block (see Fig. 13.0 below). Copy the diagram and complete it by
drawing the ray which emerges at C. Name what is happening at A and at B.

14 The diagram shows a long block of glass over an object O. Light from O reaches the top surface of the glass
at X, Y and Z.

a) What is the name given to the bending of the light at X?

b) Fill in the two missing words in the following sentence.
At Z light is ..................... ........................... reflected.
c) What is the angle marked R called?
d) Why is light reflected as shown at Z?

Page 98
12.0 LENSES
12.1 Introduction
Lenses are usually used in various optical instruments to produce images. A lens would bend or refract a light ray to
produce an image. They often have spherical surfaces. There are two types of lenses, namely
i) Convex/converging lens
ii) Concave/diverging lens
iii)

A converging lens is thicker at the middle and thinner at the edges and it bends light inwards.
On the other hand a concave is thinner at the middle and thicker at the edges and it spread out light.
When a parallel beam of light passes through a convex lens the rays bend inwards and converge or meet at a point known
as a FOCUS. When the rays pass through a concave lens and are parallel to its axis, they are bend outwards (spread out or
diverge). The point from which the rays appear to diverge it is the principal focus of the lens.
*NB:- for a convex lens the rays actually converge at the principal focus so it is said to be real.
DEFINING TERMS
➢ Optical centre (c):- centre of the lens
➢ Principal axis:- a straight line through the optical centre at a right angle to the lens.
➢ Principal focus (F):- a point on the principal axis where parallel rays converge or a point where parallel rays
appear to diverge from for a concave lens. Rays can pass through the lens from either direction so there is
another principal focus F’ on the opposite side of the lens and is the same distance from the lens as F.
➢ Focal length (f):- distance from the principal focus to the optical centre.

MEASUREMENT OF THE FOCAL LENGTH.

A simple method of determining the focal length of a convex length is by focusing the image of an object which is far away
from the lens on a wall/screen. The distance from the lens to the screen on which the image is formed is approximately the
focal length of the lens.
• PLANE MIRROR METHOD
A more accurate method involves the use of a plane mirror which reflects rays from an illuminated object (cross-wire) in front
of the lens. The lens position is adjusted until a real image is formed next to the object.

Page 99
AN ACTION OF A THIN CONVEX LENS ON A RAY OF LIGHT
When a light ray strikes a thin convex lens it is refracted at both surfaces of that lens. When light ray strikes and passes
through the first surface it will bend towards the normal since it is moving from less dense to more dense medium (air →
glass). When it leaves the second surface it will bend away from the normal because the ray is now moving from denser to
less dense medium (glass → air).
12.2 FORMATION OF IMAGES BY A THIN CONVEX LENS
A converging lens can produce both real and virtual images. The properties of the image formed depend on the position of
the object from the lens in front of the lens. They can be obtained experimentally or graphically by drawing ray diagrams. In
constructing ray diagrams any two of the following standard rays maybe used:
i) Ray I: A ray parallel to the principal axis is refracted through the principal axis after leaving
the lens.
ii) Ray II: A ray through a principal focus F, when it leaves the lens , it is refracted parallel to the
principal axis.
iii) Ray III: A ray through the optical centre passes straight through the lens undeviated (not
refracted).
EXAMPLES
Case I: Object beyond 2F’

Image is:- real, Diminished/reduced, inverted and between F and 2F.

Case II: Object at 2F’

Image is:- real, inverted, same size as the object and at 2F.

Case III: Object between 2F’ and F’

Image is:- real, inverted, magnified/enlarged and beyond 2F.

Page 100
Case IV: Object at F

Image is at infinity.

Case V: Object between F and the lens

Image is:- virtual, enlarged, erect (upright) and behind the object

Note

RAY DIAGRAMS FOR A CONVEX LENS

Standard rays: In ray diagrams, any two of the
following rays are needed to fix the image position
and size.
(a)A ray parallel to the principal axis passes
through the Principal Focus F after being
(c) A ray through the optical center
(C) passes straight through the lens

refracted by the lens

(b)A ray through the principal focus F1

which is refracted parallel to the principal
axis

12.3 OPTICAL INSTRUMENTS

1) MAGNIFYING GLASS
A convex lens can be used as a magnifying glass if the object is placed between the lens and the principal focus. The
images will be enlarged, virtual, erect and on the same side of the lens as the object. (See case V above)
2) CAMERA
A convex lens used in a camera to form a small inverted, real image on a piece of film.

Page 101
 ➢ The Lens:- focuses the image of the object on a light sensitive photographic film placed at the back of the
camera. The lens is moved in or out to make focusing adjustment.
➢ The Shutter:- opens and shuts quickly to let a small amount of light into the camera.
➢ The film: is kept in darkness until the shutter opens. It is coated with light sensitive chemicals which are changed
by different shades and colours in the image. When the film is processed, the changes are fixed and a negative is
developed. The negative is later used to print the photographs.
➢ The diaphragm:- is a set of sliding plates between the lens and the film. It controls the aperture (diameter) of the
hole through which light passes. In bright scenes, a narrow aperture is used but in dark a wider aperture is
necessary.
*NB: i) For closer object, the lens must be moved further away from the film.
ii) For very distant object, the film needs to be at F.

3) SLIDE PROJECTOR
A slide projector uses a convex lens to form a large, inverted, real image on the screen. The object is a brightly lit piece of
transparency (slide) with a picture/information on it.

➢ The projection lens: forms the image on the screen. To get a large image the lens has to be a long way from the
screen. The focusing adjustments are made by moving the lens backward and forward in its holder.
➢ The transparency or slide: must be upside down to get an upright picture (image) on the screen. The slide must
be positioned just outside the principal focus F of the lens in order to obtain an enlarged image on the screen.
➢ The condenser lens system: a special convex lenses arrangement which helps to concentrates the light on the
slide so that it is very bright and evenly lit.
➢ The lamp: produces light that illuminates the object (slide) in order to produce a bright/sharp image on the screen.
➢ Concave mirror: reflects light to the condenser lens system.

4) PHOTOGRAPHIC ENLARGER
-Uses the same principles as the slide projector. The only difference is that with the photographic enlarger the screen is a
film which is coated with light sensitive chemicals e.g. silver salts.

12.4 LENS EQUATION

For any diagram there is a relationship between image distance, the object distance and the focal length of the lens and is
given by:-
1/f = 1/u + 1/v
Where u = object distance from the lens

Page 102
 v = image distance from lens
f = focal length of lens
12.5 LINEAR MAGNIFICATION
This is the ratio of the linear dimensions of the image to the linear dimensions of the object.
M = height of image/height of object
= HI/HO
OR
M= distance of image from the lens/distance of object from the lens
M = v/u
12.6 QUESTIONS
1. Fig. 1.0 shows three parallel rays of light reaching the front surface of a converging lens. Copy the diagram
and continue the rays to show what happens to them as they pass through the lens and into the air on the
other side.

2. Where must the object be placed for the image formed by a convex lens to be
a) Real, inverted and smaller than the object,
b) Real, inverted and same size as the object,
c) Real, inverted and larger than the object,
d) Virtual, upright and larger than the object?

3. A lens has a focal length of 4 cm. An object 2 cm high is placed 8 cm from the centre of the lens. Where is
the image formed? Describe the image: is it real or virtual, upside-down or upright, enlarged, same size or
smaller? What happens to the size and position of the image if the object is moved further away from the
lens?

4. The diagram shows an object O in front of a converging lens. The points marked F are focal
points of the lens.

a) Draw two rays from the top of the object in order to locate the position of the image.
b) The image is upright. State two other characteristics of the image.
5. Lenses are used in many optical devices. Copy and complete the table below about the images
formed by some optical devices.
Optical device Nature of image Size of image Position of image
Projector Magnified
Magnifying glass Behind the object
camera Real

6. An object is placed closer to a converging lens than its principal focus. The figure shows an
incomplete ray diagram for the formation of the image.

Page 103
 Copy and complete the ray diagram and draw the image formed.
7. The diagram shows a converging lens forming a real image of an illuminated object. State two
things that happen to the image when the object is moved towards F.

8. a) An object 1 cm high is placed 3 cm from a thin converging lens with a focal length of 5 cm.
Draw a ray diagram to find the position of the image.
b) What is meant by magnification? How is the magnification in (a) above?
c) Name one application of a converging lens used in this way.

13.0 ELECTROMAGNETIC SPECTRUM

13.1 INTRODUCTION
Electromagnetic spectrum is a family or an array of electromagnetic waves arranged according to their wavelengths or
frequencies in the ascending or descending order.

Electromagnetic waves have some similar characteristics but have different wavelengths and frequencies. They are
produced by the movement of electrons in the materials. An E.M wave is a wave consists of electric and magnetic field
(force) vibrations/oscillations which travel perpendicular to each other as well as the direction of the wave travel.
13.2 COMMON PROPERTIES OF E.M WAVES
➢ All E.M waves do not need medium to travel through. They can all travel through a vacuum.
➢ They all travel at the same speed in space which is the speed of light in a vacuum (c = 3 x 10 8 m/s)
➢ They are all progressive transverse waves. Therefore they exhibit interference, diffraction, reflection and
polarization.
➢ They obey the wave equation
C= fλ
➢ They can carry energy from one place to another and can be absorbed by matter and cause heating and other
effects.
*NB: The space occupied by each type of wave in the E.M spectrum is called a BAND.
13.3 COMPONENTS OF E.M SPECTRUM (E.M WAVES)
a) GAMMA RAYS
Source: nuclei of radioactive elements (e.g. cobalt-60) and cosmic rays
Wavelength: 10-12 m

Page 104
 Detectors: photographic film, cloud chamber, Geiger Muller tube
Properties: - very penetrating
-transmit more energy than x-rays
- ionize gases
Uses: -used in radiotherapy to treat cancer cells and destroy tumours inside the body
-used to find flaws in metals
-used to sterilize medical equipment & dressings
- used to irradiate food to kill germs in them
Sideeffects: - harmful to humans in excess; damage body cells(cause mutation and cancer) and can cause
sterility.

b) X-RAYS
Source: produced when high energy electrons are fired at a metal in x-ray tube.
Wavelength: 10-10 m
Detectors: photographic film, fluorescent screen
Properties:- very penetrating (but less than gamma rays)
-have high energy
- ionize gases
Uses: -used in radiography (to take x-ray pictures)
-used to kill cancer cells (cancer cells absorbs x-ray more readily than normal healthy cells) and treat skin
disorders.
Side efffects: - causes cancer
c) ULTRAVIOLET RAYS
Sources: - sun (U.V is the sun rays that gives suntan)
-Mercury vapour lamps – created by passing the current through mercury vapour in fluorescent
tubes
Wavelength: 10-8 m
Detectors: photographic film, fluorescent chemicals, photocells
Properties: -absorbed by glass
-causes suntan
-causes chemicals to fluorescence/glow
Uses: -kills bacteria
-produce vitamin D and melanin in the skin
-used to detect forgeries
Side effects: -causes sunburn or even skin cancer if in excess
-harmful to eyes

d) VISIBLE LIGHT/WHITE LIGHT

Sources: -sun, lamps and all luminous objects
Wavelength: 10-6 m
Properties: -is a mixture of different colours and can be split by a prism into the visible spectrum.
-ocupies a small part of the spectrum but is the only component that can be detected by
human eyes
Detectors: eye, photographic film, photocells
Uses: useful for vision/sight
Used for photography
Useful in some chemical reactions, e.g. photosynthesis.
Side effects: too more exposure may lead to skin tan

e) INFRARED
Sources: sun, warm and hot objects (e.g. heters, grills, etc.), remote controllers
Wavelength: 10-4 m
Detectors: special photographic film, phototransistor, sensitive thermometer, thermopile
Properties: All objects give out infrared radiation; the hotter the object is the more radiation it gives out.
-causes heating when absorbed by matter
Uses: - used for heating and cooking
- used for photography through haze and fog and in dark

Page 105
 - used in remote controls
- night vision
- detecting warm and cool skin and tracing infection.

f) RADIO WAVES
Sources: microwave oven (microwaves)
-Tv and radio transmitters using electronic circuits and aerials
Wavelength: 1 cm – 1 km
Detectors: aerials connected to radio and tv sets, mobile (cellular) phones, satellite dishes, radar
Properties: -They have the longest wavelengths and lowest frequencies.
Uses:
• Microwaves: are high frequency radio waves (but have shortest wavelength amongst radio waves). They are
used in RADAR (Radio Detecting And Ranging) to find the position of aeroplanes. Microwaves are also used for
cooking- water particles in food absorb the energy carried by microwaves.
• UHF (Ultra High Frequency) and VHF (Very High Frequency) waves
UHF- used in tv transmissions
VHF- used in local radio transmissions
• Short, Medium and long radio waves:
Medium and long waves are used to transmit over long distances because their wavelengths allow them to diffract
around obstacles such as buildings, hills, etc.
Communication satellites above Earth receive signals carried by high frequency short waves.
These signals are amplified and re-transmitted to other parts of the world.
13.4 QUESTIONS
1) This is a list of types of waves:
gamma infrared microwaves radio ultraviolet visible x-rays
choose from the list the type of wave that best fits each of these descriptions.
a) stimulates the sensitive cells at the back of a human eye.
b) necessary for a suntan.
c) used for rapid cooking in an oven.
d) used to take a phograph of the bones in a broken arm.
e) emitted by a video remote control unit.
2) Gamma rays are part of electromagnetic spectrum. Gamma rays are useful to us but can also be very
dangerous.
a) Explain how the properties of gamma rays make them useful to us.
b) Explain why gamma rays can cause damage to people.
c) Give one difference between microwaves and gamma rays.
d) Microwaves travel at 300 000 000 m/s. what speed do gamma rays travel at?
3) Write down the parts of the electromagnetic spectrum in order of increasing wavelength.

SOUND 14.1 INTRODUCTION

Sound is produced by vibrating objects such as drums, turning forks, loudspeakers, ticking clock, etc. As the object vibrates
back and forth, the particles around it are compressed (squashed) and rarefacted (stretched). This compression-rarefaction
process continually repeats itself while the vibration continues. The series of compressions and rarefactions form a sound
wave.
In a compression, particles are squashed together and hence this is a region of high pressure whilst in a rarefaction particles
are further apart, stretched over relatively larger space and therefore this is a low pressure region.

Page 106
*A sound wave can also be defined as a form of radiation consists of series of pressure variations propagating
through a medium
Sound waves are longitudinal i.e. the vibrations of the particles are parallel to the direction of the wave travel.
Definition;
a) Wavelength (λ) of a sound wave:- the distance between two successive compressions or rarefactions.
b) Speed (v) of a sound wave is the distance travelled by the wave in one second.
c) Frequency (f) of a sound wave:- number of complete waves produced in a second or number of complete oscillations
(vibrations) made by the source in one second.
* The sound waves obey the wave equation; v = fλ

14.2 SPEED OF SOUND

There are two ways to find the speed of sound in air
i) Experiment 1: Echo method

|<------------------------------------- s ---------------------→|
Two people stand a distance s from a large hard wall/cliff. One produces sound by banging two pieces of metals together
and the other holds a stopwatch and records the time taken for the sound to go to the hard wall and back
To find the speed of the sound, divide the total distance travelled by the time taken recorded by the stopwatch
v = 2s/t

ii) Experiment 2: Pistol method

A<------------------- 100 m ------------------------->B

Two students stand distance s (let say s = 100 m) apart. Student A has a gun and student B has a stopwatch. Student A
fires the gun. Student B starts the watch when he sees the smoke from the gun and stops the watch when she hears the
bang. The speed of sound is calculated by dividing the distance travelled (100 m) by the time taken, recorded by the
stopwatch.
i.e. v = s/t
NB: i) The observer will always see the action (smoke) before hearing the sound (or during a storm, the lightning flash is
seen before the thunder is heard). All these show that the speed of sound is much slower than the speed of light.
ii) Speed of sound in solids, liquids and gases: Sound travels at different speeds in different materials. It travels fastest in
solids, then liquids and slowest in gases.
Fastest --------------------------------------------------------> slowest
Solids liquids gases
(6000 m/s in steel) (1500 m/s in water) (330 m/s in air and this is far less speed of light)
Sound waves consist of vibrating particles. Therefore if there are no particles, sound waves cannot exist. This means that it
is impossible for sound to travel through a vacuum. This is usually demonstrated using a bell jar, a bell and a vacuum
pump.

Page 107
The sound of the bell fades when the air is removed from the jar. If the jar is completely evacuated, no sound is heard even
when the hammer continues to hit the gong. The sound returns when air is let back into the jar.
14.3 TYPES OF SOUND WAVES
Different sounds have different frequencies.
Infrasonic waves | audible sound waves | ultrasonic waves/ultrasound
20 Hz 20 kHz
i) Infrasonic waves(infrasound):- have frequencies below 20 Hz e.g. earthquake/seismic waves and can be detected by
dogs.
ii) Audible sound (waves) – sound that can be detected by human ears. Their frequency ranges from 20 Hz to 20 kHz.
iii) Ultrasonic waves (ultrasounds) - have frequencies higher than 20 000 Hz (20 kHz). They can be detected by bats. A
bat emits and receives ultrasonic waves and this helps them to navigate at night and judge the distance of obstacles ahead.

How do we use Ultrasound

a) Used in spectacles for the blind
b) Used in echo sounding or sonar (sound navigation and ranging) in ships to determine the depth of the sea.
c) Used in ultrasound scanning in hospitals. Ultrasound waves are reflected from different layers of tissues in the body and
so can produce quite clear images. They also have lower energy than X-rays and so are less hazardous to human cells.
Ultrasound scans are especially useful for obtaining pictures of unborn babies in the womb. Very high Frequency sound
waves are transmitted into the womb of a pregnant mother. The sound is reflected from the embryo and the information is
used to produce an image of the baby.
d) Used to clean delicate machinery or street light covers – machinery is put in a tank of liquid which has an
ultrasonic vibrator in the base.
e) In hospitals, a concentrated beam of ultrasound is used to break up kidney stones and gall stones without
patients needing surgery.
d) Used to detect flaws in metals using the idea of echo-sounding. A pulse of ultrasound is sent through the
metal. If there is a flaw (tiny gap) in the metal, two pulses are reflected back to the detector; one from the
flaw and the other from the far end of the metal.

14.4 MUSICAL NOTES

Irregular vibrations such as those of motor engines produces noise whilst regular vibrations such as those that occur in
musical instruments produce musical notes which have three properties; namely;
a) pitch b) loudness c) pitch
a) Pitch
Pitch of a musical note depends on the frequency of the sound wave. Sound with high frequency is heard as high note
and is said to be high-pitched. Low notes have low frequencies and said to be low-pitched.

Sound A has a higher pitch than sound B because has higher frequency. With a higher frequency more waves are
produced and the waves are closer together.
NOTE: i) A high-pitched sound also has a short wavelength while a low-pitched sound has a longer wavelength.
ii) Musical notes are said to be octave apart if the frequency of one is twice that of the other.
b) Loudness
The loudness of a sound depends on the amplitude of the sound wave. Quiet sounds (notes) have small amplitude,
loud sounds have larger amplitude. The loudness of sound is measured in decibels (dB).

Page 108
Sound B is louder than sound A because the wave has a larger amplitude.
*The greater the amplitude, the louder the sound.
c) Timbre
The timbre of a sound describes the purity or quality of sound. Pure note (e.g. one emitted by a turning fork) has only one
frequency but other notes consist of a main or fundamental frequency with others, called overtones (which are usually
weaker and with frequencies which are exact multiples of the fundamental frequency). The number and strength of the
overtones decides the quality of a note.

Sound B is a pure note from a turning fork. Sound A is produced from a piano. The two sounds have almost the same
pitch (main frequency) and loudness but differ in quality because sound A is actually a combination of several different
sounds with slightly different frequencies.
Note:
The frequency (pitch) of a note produced by a vibrating material (e.g. string) depends on:
i) length of the material; short strings produce high notes and therefore halving the length doubles the frequency
ii) tension in material: tight wires produce high notes
iii) mass per unit length; thin strings give high notes.

14.5 ECHO AND REVERBERATIONS

14.5.1 ECHO
Sound is reflected when it meets some kind of obstruction such as a wall, high cliff or the bottom of an ocean. The reflected
sound (wave) is called an echo. In ships, echo can be used to find how deep the ocean is or to detect the shoals of fish.

A pulse of sound is transmitted to the sea bed and is reflected back to the boat. The time interval between transmitting and
receiving the pulse is measured. Then the depth of the sea is calculated using the total distance travelled by the pulse which
is twice distance to the obstruction.
Example:
A sound pulse is transmitted from the boat, and 10 s later an echo is received. How deep is the ocean? (The speed of sound
in water is 1500 m/s).
Data
: v = 1500 m/s, t = 10 s, d = depth of sea = ?, d = (v x t)/2
total distance travelled by pulse = 2d = (1500 x 10)/2
v = 2d/t = 7500 m
14.5.2 Reverberations
When playing a musical instrument, e.g. piano, in an enclosed area (e.g. inside a hall), some of the sound of the piano will
be reflected off the walls of the hall. You will hear the direct sound first, then early reflections and then multiple reflections all
in a very short time and this will cause the sound to die off gradually over some time. This effect is called reverberation. A
reverberation can also be obtained when a sound is reflected from a surface which is nearer than 15 m, here the echo joins
the original sound and then the sound seems to be elongated or prolonged.

Page 109
 The shape and size of the hall will affect the amount of reverberations reaching the listener. These factors are called the
acoustics of the hall. Rooms with good acoustics are very important when recording music or when designing
conference centres. Optimum reverberations are desirable but too much causes confusion.

14.6 NOISE POLLUTION

Unpleasant sound which may be even harmful to people is called noise. Sound is unpleasant if it is very loud or has a very
high frequency. Noise can damage the ears, cause loss of concentration and if very loud result in sickness and temporary
deafness.
Ways of reducing unwanted noise (noise pollution)
• Designing quieter engines and better exhaust systems.
• Using sound-insulating materials such as carpets, curtains and double-glazed windows in our houses
• Tractor drivers, factory workers and other people regularly exposed to noise often have to wear ear protectors.
• Where practical keep as much greater distance away from the source of the noise as possible.

14.7 PROBLEMS
Q1. A ship searching for fish emits sound waves which are reflected from the sea bed. If the speed of sound in
is known and the time that elapses before the echo is heard is measured, it is possible to calculate how
deep the water is at that point.
a) What will the operator hear if a shoal of fish swims under the ship? How could the operator very roughly
assess how deep the shoal is?
b) Suggest one way in which the detector might be receiving a false signal (i.e. there are no fish below).
c) If sound waves travel through water at 1500 m/s,
i) how deep is the sea-bed if echo is heard after 1 s?
ii) how quickly is an echo heard if a shoal of fish swims 250 below the ship?
Q2. A microphone is connected to an oscilloscope (CRO). When three different sounds A, B and C are made in
front of the microphone, these are the waveforms seen on the screen.

a) Comparing sounds A and B, how would they sound different?

b) Comparing sounds A and C, how would they sound different?
Page 110
 c) Which sound has the highest amplitude?
d) Which sound has the highest frequency?
e) Sound A has a frequency of 220 Hz. If the speed of sound is 330 m/s, what is the wavelength of sound A?
f) What is the frequency of sound C?
Q3. The diagram below shows the oscilloscope traces of two different sounds A and B. The oscilloscope setting
is the same in both cases.

a) A and B sound different.

Write down two differences in the way they sound. Explain your answers as fully as you can.
Q4. A man standing on a beach 340 m from a tall cliff hears his echo after 2 s.
a) What is an echo?
b) Explain how echoes can be used to discover the depth of water under boat.
c) Using the information above calculate the speed of sound in air
d) What are ultrasonic waves?
e) Give at least two uses of ultrasonic waves.
Q5. Sound X: frequency 10 000 Hz.
Sound Y: frequency 30 000 Hz.
Upper limit of human hearing: 20 000 Hz.
a) (i). What is the upper limit of human hearing in kHz?]
(ii). Which of the above sounds is an example of ultrasound?
b) Ultrasound can travel through some human tissues and can be reflected by different layers in the body.
(i). Describe one example of how ultrasound is used in hospitals.
(ii). For producing medical images, why does doctors prefer to use ultrasound if they can, rather than X-
rays?
(iii). Describe one example of the industrial use of ultrasound.
Q6. (a) Draw a diagram of a wave. Label both its amplitude and its wavelength.
(b) Your diagram represents a sound wave. What would you hear if;
i. the wavelength got shorter?
ii. the amplitude got larger?

15.0 MAGNETISM
Magnet is an object that attracts certain objects which are made from magnetic materials.
Magnetic materials: are materials attracted by a magnet e.g. iron, cobalt, nickel and alloys such as steel, alnico and
alcomax. These magnetic alloys usually contain iron, cobalt, nickel and steel. SINC. These materials (magnetic materials)
are also called ferromagnets.
Non-magnetic materials: substances that cannot be attracted by a magnet. These include copper, brass, zinc, tin and non
metals (e.g wood, glass, etc)
15.1 PROPERTIES OF MAGNETS
a) Magnets attract magnetic materials and do not interact with non-magnetic materials.
b) Magnets have magnetic poles. These are areas in a magnet where magnetism (magnetic force) seems to be
concentrated and stronger. To determine the magnetic poles dip a magnet into iron filings. Most of the
filings stick in clumps around the ends of the magnet with few if any in the middle.
c) North and south poles
If a bar magnet is suspended so that it can swing freely it will always come to rest in approximately N-S
direction. The end pointing to the earth geographical north is called the North seeking pole or North pole (N)
and the end pointing to the geographical south is called the South seeking pole or South pole (S).
d) Law of magnetic poles
If a north pole of a magnet (test magnet) is brought closer to a north pole of another magnet, repulsion will
take place. If a North pole of one magnet is brought close to the south pole of another magnet attraction
takes place.

Page 111
 *Likes poles repel, unlike poles attract.
15.2 INDUCED MAGNETISM
This is the magnetism that appears or develops in a magnetic material due to bringing the material near or in contact with a
permanent magnet. The inducing pole of the magnet will always induce an opposite pole to nearer end of the material.

15.3 METHODS OF MAGNETISATION- MAKING A MAGNET

1) Stroking
a) single stroking/touch
- stroke the magnetic material (steel rod) from end to end with the
same pole of a magnet.
- lift the magnet high above the rod and repeat the stroke several times (always in
one direction).
- the end where stroking ends will have an opposite polarity to the stroking pole ( and
the end where stroking started will have the same polarity as the stroking pole).

the same time.

- repeat several times * if the same the same
poles are used, similar poles will be formed at the ends
of
the magnetic material and this will not be a proper
magnet.

b) Double touch (Divided touch)

- use opposite poles of two magnets to stroke the
rod from the centre outwards at

Page 112
2) Electrical method: The industrial way of making magnets is by making use of the magnetic field created
when current flows through a conductor. The magnetic material is placed inside a solenoid (a long coil of
insulated copper wire) through which D.C (direct current) is passed. The current is switched on and off,
when the material is removed it would be found to be magnetized. (The coil should be placed in the N-S
direction).

To determine the polarity, the right hand grip rule is used. The fingers are placed such that they follow the direction of
current around the coil and thumb will point to the North pole.

15.4 METHODS OF DEMAGNETISATION

i) Electrical Method :- a bar magnet is placed inside a solenoid through which A.C (alternating current) is
passed. The bar is slowly withdrawn from the solenoid whilst the current is still on. The solenoid should be

placed in the E-W direction.

ii) Magnets can be demagnetized by heating them strongly and then leave them to cool placed in the E-W
direction.
iii) can also be demagnetized by hammering (whilst lied in the E-W direction)
15.5 MAGNETIC SATURATION
Magnetic materials such as iron and steel have individual atoms which act like atomic magnets or magnetic dipoles. The
neighbouring atoms set themselves with their magnetic axis parallel. The grouping of atomic magnets or atomic dipoles with
parallel axes is called magnetic domain.
In an unmagnetised material, the magnetic domains will point in different directions and hence the material as a whole will
show no polarity. When a magnetic material is magnetized, the domains are re-aligned such that most of them have their

Page 113
axes pointing in the same direction. There is a maximum level of the magnetization which is called magnetic saturation. This
happens when the atomic dipoles in all magnetic domains have been re-aligned and their magnetic axes are parallel and
pointing in the same direction.

15.6 MAGNETIC FIELD

Magnetic field is the area or space around a magnet where the magnetic force is effective or felt. The force is not is equally
distributed but follows a pattern of lines.
The magnetic force of a magnetic field is along curved path known as a field line. It is usually directed from North to South
pole.
The magnetic field around a magnet can be detected by using iron filings or a plotting compass.
i) iron filings:- place a sheet of paper over the magnet. Sprinkle iron filings onto the paper and tap the paper a
bit. The iron fillings turns around in the direction of the magnetic lines of force. They form a pattern showing
magnetic field lines around the magnet.
ii) plotting compass: the bar magnet is placed on top of a sheet of paper. Place the plotting compass at the
end of the bar magnet. When the compass has settled mark on the paper the ends of the needles of the
compass. Move the compass to a new position so that its other end is over the last mark previously made.
Mark another dot where the needle is pointing. Repeat the procedure until the compass reaches the other
end of the magnet (expt. Pg 223 GCSE). Join the dots to form a single line from one end of the magnet to
the other.
PATTERNS OF ELECTRIC FIELD
i) Field lines around a single magnet

Field lines always move from north to south. They never cross each other. And where the lines are closer together
shows areas with stronger magnetism (magnetic force).
ii) field lines between unlike poles

iii) field lines between like poles

Page 114
 There is a neutral point X between the poles where the field cancel out each other.

15.7 MAGNETIC PROPERTIES OF STEEL AND IRON

Both iron and steel can be induced to form magnets.
EXPERIMENT 1

Each pin or clip magnetises the one below it by induction and unlike poles so formed will attract. When the chain of iron nails
is removed from the magnet, it will collapse. When the chain of the steel paper clips is removed from the magnet, the clips
will remain attached to each other. These indicate that magnetism induced in iron is temporary while magnetism induced in
steel is permanent
Conclusion: steel is a hard magnetic material i.e. it is very hard to magnetize steel but once magnetized steel will not
lose its magnetism easily.
Iron is a soft magnetic material i.e. iron can be magnetized easily but it will lose its magnetism easily.
EXPERIMENT 2
Attach a strip of soft iron and a strip of steel to the N pole of a magnet.
Dip the free ends of the strips in iron filings

More filings stick to the soft iron. So the induced magnetism in the iron is slightly greater. When the strips are detached from
the magnet, most of the filings fall from the soft iron but few fall from the steel. This shows that the induced magnetism in
soft iron is temporary but magnetism induced in steel is permanent.

15.8 USES OF MAGNETS

1). Permanent magnets
They are used in construction of electric motors, bicycle dynamos, generators, loudspeakers, electricity meters,
microphones and can also be used as door catches.

Page 115
2). ELECTROMAGNET
This is a temporary magnet made by winding a coil of wire around a soft iron.

The soft iron will only be magnetized when current flows through the coil. When there is no current flowing, the soft iron will
lose its magnetism. Steel is not suitable to be used as a core since it is a hard magnetic material. With steel the
electromagnet will keep its magnetism even when the current is switched off.
*NOTE:
1. Without the iron core, an electromagnet would be much weaker. The core concentrates the magnetic field into a
small volume of space and hence producing a stronger electromagnet.
2. The strength of the electromagnet can be increased by:
• Increasing the current
• Increasing the turns in the coil
• Using an U-shaped core so that the poles of the electromagnet would be close to each other.

Uses of Electromagnet
1. Large electromagnets are used for lifting heavy magnetic materials in scrap-yards. A crane moves the material to
its new place and when the current is turned off, the material is released from the electromagnet.
2. Electric bell
It consists of an electromagnet that repeatedly switches itself on and off very quickly.

When the press-button switch is pressed, the current flows through the electromagnet, which pulls the
springy metal together with the hammer so that it hits the gong and the sound is made. This movement, at the same time,
separates the contacts and switches off the circuit. The hammer goes back, the contacts close again, the current flows once
more and the electromagnet pulls the hammer across again, this goes on and produces continuous sound until the circuit is
switched off.

Page 116
 3. The magnetic relay
This is a switch operated by an electromagnet. In a relay a small switch with thin wire can be used to turn on the current in a
much more powerful circuit.

When the switch S in the input circuit is closed, the current flows through the electromagnet. This pulls one end of the iron
armature towards electromagnet and cause the other end to push and close the contacts at C and completing the output
circuit. As a result, a current flows through the motor.
4). Reed switch

When the current moves through the coil, the magnetic field created would magnetize the reeds (thin strips inside the
glass tube). The current flows such that the ends of the two reeds develop opposite poles and then the reeds will attract
each other thereby completing the circuit connected to their other ends (AB). The reeds separate once they the current
in the coil is turned off.
Reeds switches are also operated by permanent magnets.

In the above diagram, a burglar alarm is activated by a reed switch. When the door is closed the magnetic fields from
the two bar magnets cancel out each and the reed switch remains open. But once the door is opened with the switch

Page 117
 closed, the reeds would be magnetized by the magnet in the door frame. The ends of the reeds will be induced with
opposite ends, they will attract, and completing the circuit and this will causes the alarm bell to ring.

5. The telephone earpiece

When someone speaks into the microphone (mouthpiece) on the other end of the line a varying electric current is
set up having the same frequency as the sound waves. Similar current will be fed to the earpiece on the other end,
when this varying current passes through the coil in the earpiece, the magnetic force on the diaphragm also
varies. Therefore the diaphragm (made of magnetic substance) moves to and fro in step with the current. This sets
the air nearby into vibration and sound waves are set up.

15.9 MAGNETIC SHIELDING OR SCREENING

Besides being used as core for electromagnets or making permanents magnet, magnetic materials can be used for
magnetic screening where an iron ring will act as a magnetic shield for anything inside it.

Iron is said to be more permeable to magnetic field than air is. Therefore magnetic field lines appear to be drawn into the
iron and concentrated through it and none through the air inside the iron. Then anything inside the iron ring would be
shielded or screened from magnetic field. This effect is known as magnetic screening or shielding.
Magnetic shielding is put to practical use when used to protect delicate measuring instruments which could be affected by
magnetic fields by enclosing them in thick-walled soft-iron boxes.
15.10 QUESTIONS

Page 118
1. A student has a piece of metal that he thinks is a magnet. He holds it near another magnet and it is attracted. The
student says this proves that his metal is a magnet. Explain why the student is wrong.
2. A, B, C and D are small blocks of different materials. The table below shows what happens when two of the
blocks are placed near one another.

Use one of the phrases below to complete the sentences that follow. Each word may be used once, more than
once or not at all.

A MAGNET A MAGNETIC MATERIAL A NON-MAGNETIC MATERIAL

a) Block A is ...................... c) Block C is ......................

b) Block B is ....................... d) Block D is ......................
3. What is the diference between a magnetically hard material and a magnetically soft material? Give an example of
each.
4. a) What is a magnetic material? Give three examples of magnetic materials.
b) Name three non-magnetic metals.
5. Study the magnets in the diagram below. What would happen in each case?

6. What is meant by a magnetic field?

7. a) Circle the names of two materials which are attracted to magnets
aluminium brass copper iron steel tungsten
b) The diagram shows a pattern of lines around a magnet.

Give the name/s of:

(i) this type of magnet ..................................
(ii) the points marked • ...................................
(iii) lines ..............................................
c). Two magnets, like the magnet shown above, were used to get the pattern of the lines
shown below.

Describe what you would do with the two magnets so that you got this pattern.

Page 119
 9. An electromagnet is made by winding wire around an iron core.

The diagram shows an electromagnet connected to a circuit.

a) State two ways of making the strength of the electromagnet weaker.
b) Explain why the core is made of iron instead of steel.
10. a) Given a bar magnet, how would you find out which pole of the magnet is its north
pole
b). How would you magnetized a steel needle and how would you tell that it is magnetized?
c) How can this magnetized needle be effectively demagnetized?

c) Is it possible to make a magnet with a single pole?

d) If you cut a magnetized steel in half. You will find out that each half is a bar magnet. What will happen if
you cut one of the halves in two? Does this produce a magnet with a single pole?
11. A current is passed through a solenoid (coil) as shown below

a) The solenoid in the diagram above behaves like bar magnet. Mark its polarity.
b) An iron rod is placed in the solenoid. What happens to it when the current is
i) Switched on
ii) Switched off
c) How would your answers in (i) and (ii) above change if the rod were made of steel?
d) What is purpose of the core in the electromagnet?
e) Give one use of an electromagnet.
12. The figure below shows a circuit that includes an electrical relay, used to switch on a motor
M.

Explain in details, how closing switch S causes the motor M to start.

16.0 ELECTRICITY
*Static electricity/electrostatics – charges at rest/ not moving.
Electrostatic charges can be induced and easily detected in insulators (non-metals) because these kinds of materials do
not allow charges to flow through them. Metals are generally good conductors so it is difficult to induce electrostatic charges
in them.
*Current electricity – moving/flowing charges (electrons)
16.1 STATIC ELECTRICITY
All materials are made out of molecules which themselves are groups of atoms. The atoms contain electrically charged
particles being protons and electrons. Normally an object is electrically neutral since it has an equal number of positive and
negative charges. The two charges can be separated by rubbing objects together.

Page 120
16.1.1 Electrostatic charging by friction: illustration
The force of friction between two objects can cause electrons to be transferred from one object to the other. One object will
gain extra electrons and become negatively charged. And the other one will become positively since it would have lost some
electrons and remained with excess positive charges.

A B
A polythene strip will be negatively charged and the cloth will be positively charged
B. cellulose acetate strip will be positively charged and the cloth will be negatively charged.
Explanation: when polythene is rubbed, electrons from the cloth are transferred to the polythene making the polythene
negatively charged and the cloth will be positive because there will be a deficit of electrons.
On the other hand when perspex (cellulose acetate) is rubbed with the cloth it loses some electrons to the cloth and remains
short of electrons and with more unbalanced protons and as a result the Perspex rod becomes positively charged and the
cloth negatively charged because it would have some extra electrons (negative charges).
16.1.2 POSITIVE AND NEGATIVE CHARGES
There are two types of charges, namely positive(+) and negative (-).

Positively charged object negatively charged object

Experiment: positive and negative charges
- Rub a piece of polythene strip with a cloth
- Hang it up as shown in the diagram
- Rub another polythene strip and bring it near the first one.

Observation: repulsion occurs

Now bring a piece of rubbed polythene close to the hanging cellulose acetate strip.

Observation: attraction occurs

This shows that the two strips became charged in different ways. The charge on the cellulose acetate is taken to be
positive and the charge on the polythene is negative.
Conclusion: “like charges repel and unlike charges attract”

16.1.3 INDUCED CHARGES

Page 121
 A charge can be build up on an uncharged object by holding a charged object close to it as shown below. These
charges that would appear on an uncharged object due to a charged object nearby are called induced charges.

A metal sphere is being charged by induction and ends up with an opposite charge to that on the rod. Note the two
never actually touched.
16.1.4 GOLD-LEAF ELECTROSCOPE
An instrument used for detecting the presence of an electric charge. It consists of a metal rod on top of which there is a
metal cap (plate). The rod is insulated from the case. A thin gold leaf is attached to the bottom of the rod.

1. Detecting an electric charge

When a positively charged rod is brought near the top plate, the leaf rises. This so because the positively charged rod
attracts free electrons in the brass rod (stem) upwards so that the plate has an excess of negative charges. The lower rod
and the leaf are left with an excess of positive charges. The leaf diverges from the stem because they are both positively
charged. On removal of the charged, the leaf falls as the extra electrons in the top plate move back down the stem.
The leaf also rises if a negatively charged rod is brought near the top plate. This time, the rise of the leaf occurs because
free electrons in the top plate are pushed downwards (repelled) by the negatively charged rod.

2. Charging an electroscope
a. Charging by contact
An electroscope can be charged by rubbing (pressing) a charged insulator firmly across the edge of the top plate.
The charge on the rod is shared with the electroscope.

b. Charging by induction

A positively charged rod is brought near the top plate. This attracts electrons upwards, leaving a positive charge
on the leaf and the stem. When the top plate is touched with a finger, the electrons on the plate remain because

Page 122
 they are held there by the attraction of the positively rod. The electrons flow in from Earth to replace the missing
electrons on the leaf. The charged on the leaf is neutralised. The leaf collapses. The finger is removed, followed
by the rod. This leaves a net negative. The leaf rises as the finger is removed.
*an electroscope can be discharged by touching it with a finger or connecting it to the earth. This earths the
electroscope. Earthing is a process of sharing charges with the Earth.

16.1.5 Unit of electric charge

The SI unit of electric charge is a coulomb. A charge of one coulomb is the charge on 6 x 1018 electrons
1 C = 6 x 1018 electrons
And this means that the charge on one electron is 1.6 x 10-19 C.
The symbol for electric charge is Q and the symbol for the coulomb is C.
PROBLEMS.
In a chemical reaction, a copper atom loses two electrons to become a copper ion. a) calculate the charge on this ion.
Answ: charge on one electron = 1.6 x10-19 c
Charge on two electrons = 2(1.6 x10-19 C) = 3.2 X 10-19 C
b) How many electrons are there in a charge of 1.28 x 10-18 C?
Answ: number of electrons = (1.28 x10-18 C) ÷ (1.6 X 10-19 C) = 8

16.1.6 DISCHARGING
A charge can be build up on an object through friction. The charge can be discharged to the Earth by contact with a
conductor. The charge stored can also be released to the nearest object with a neutral charge or by bringing discharging
object with opposite charge.
e.g. when sliding out of a car, friction between the seat and clothes causes a charge on the person. When the person
touches the car body the charge passes from his body to the car, giving a slight shock.
*NB: an isolated charged insulator will slowly become discharged. The charge on the insulator is neutralized by ions
(charged particles) in the air.
The Van de Graaff generator

The Van de Graaff generator produces a large and continuous supply of electric charge. In this machine a rubber belt rubs
against a plastic roller and becomes charged. The charge is carried on the moving belt up to the metal dome, where it is
collected. A large quantity of charge therefore builds up on the dome.
*woollen threads attached to the dome will repel each other strongly after the generator has been running for a while.
*when a metal sphere, connected to Earth with lead, is brought near the metal dome, electric sparks are produced. This
occurs as charges from the dome pass through the air to sphere and then to the earth. This discharges the dome.
LIGHTNING
Friction between particles rubbing against each other in a large cloud can build up a large charge on the cloud. When the
charge becomes very large it may discharge through the air to the earth or to the neighbouring clouds and this would be in a
form of flash of lightning, therefore lightning is an electric discharge between the Earth and highly charged clouds.
Lightning conductors
A lightning conductor is a thick copper strip fixed to the outer wall of a building or a tall pole near the building. The top of the
rod ends are sharp spikes. At the bottom of the strip there is a copper plate buried in the ground.

Page 123
Thunderclouds contain a large quantity of negative charge on their underside and positive charge on their tops. When a
cloud pass over a building it induces build-up of opposite charges (positive charges) on the roof. If the electric field
(voltage) between the opposite charges is strong enough, there may be a spark of lightning as the charges flow through the
air towards each other.
With a lightning conductor, the sharp spikes at the top reduce the chance of a lightning strike. By effect of action at points,
the conductor let charges on the building leak away before a spark can occur and some of the charges also flow earlier up
to the clouds and cancel out some of the negative charge on the clouds, making it less likely that the lightning will strike.
However, if a flash does occur it is less violent and the conductor gives it (negative charge) an easy path to the ground.

16.1.7 ELECTRIC FIELD

A region around an isolated electric charge where the electric force can be felt by a charged object. The field lines have both
the magnitude and direction. They always move away from the positive charges and move towards negative charges.
PATTERNS OF FIELD LINES
a) A field around an isolated electric charge

b) Field lines around unlike charges

c) Around like charges

Page 124
16.1.8 ELECTROSTATIC INDUCTION
The process of electrically charging an insulated conductor using the force due to a charged object to separate the charges
in the conductor.
a) Separation of conductors

b) Earthing

Charges separated by bringing a charged rod close to the sphere.

While the rod is still kept at its position, the sphere is earthed by touching with hand -
electrons flow out to earth.

Page 125
Charges are evenly distributed around the sphere when the rod and the earth (hand) are removed.
16.1.9 INSULATORS AND CONDUCTORS
Insulators or bad conductors- they can hold charge on their surfaces. The charge does not move through insulators.
Examples:- plastics (e.g. PVC, polythene, Perspex, etc.), glass, rubber, dry air, sulphur and oil.
Conductors – metals are good conductors of electricity since they have free electrons in their outermost shells. A conductor
cannot be charged as the charge will flow easily through it.
Examples:- most metals (e.g. silver, copper, aluminium), carbon, graphite, acid solutions, salt solutions
Semi-conductors:- are in-between materials. They are poor conductors when cold but much better conductors when warm,
e.g. silicon, germanium
Water, human body, earth and air are called poor conductors – they conduct very slowly
16.1.10 APPLICATIONS AND DANGERS OF ELECTROSTATICS
1. Usually electric charges build up on the surface of the car as it moves through air along the road that is why a
passenger may get an electric shock when getting into or out of the car. Therefore if charges are allowed to build
up on trucks carrying flammable goods (e.g. petrol) a very small spark can cause a fire or explosion. It is then
important that such trucks are earthed by attaching a conducting strip that will be dragged behind the truck or run
on conductive rubber tyres.
2. Paint spraying – the paint becomes charged due to friction as it is forced out of the nozzle of the spray gun. If the
object to be painted is given the opposite charge the paint will stick to it very well. This technique is used by
farmers when crop spraying and also used to coat cars with paint.
3. Dust and ash precipitator - ash in factory chimneys and power stations can be removed by electrostatic
precipitation. Wires inside the chimneys are negatively charged and give a similar charge to the ash particles. The
negatively charged ash particles are attracted to positively charged metal plates inside the chimney walls. The ash
particles are then removed by washing
4. In electrostatic photocopying machines – inside the photocopier, there is a light-sensitive plate that would be given
a negative. The image of the document to be copied is projected onto the drum. The bright areas on the drum lose
their because of reflected light from the corresponding white parts on the document paper but the dark areas on
the plate keep their charge. The powdered ink (toner) is attracted to the charged (dark) areas. A blank sheet of
paper is pressed against the plate and picks up the toner. The paper is heated so that the powered ink melts and
sticks to it. The result is a copy of the original document

16.1.11 QUESTIONS
Q1.a) Name two types of electric charge.
b) A student wants to charge his plastic comb. Describe one way he could charge the comb.
c) the student then holds his charged comb near some small pieces of paper.

Page 126
 Suggest what might happen to the paper.
Q2. When a balloon is rubbed in your hair, the balloon becomes negatively charged.
(i) Explain how the balloon becomes negatively charged.
c) the negatively charged balloon is brought up to the surface of a ceiling. The balloon sticks to the
ceiling. Explain how and why this happens.
Q3. Say whether the following attract or repel
a) two negative charges
b) a negative charge and a positive charge
c) two positive charges
Q4. In an atom, what kind of charge is carried by i) protons ii) electrons c) neutrons
Q5. a) Why is it easy to charge polythene by rubbing, but not copper?
b) What makes copper a better electrical conductor than polythene?
c) name one non-metal that is a good conductor.
Q6. When one pulls a plastic comb through their hair, the comb becomes negatively charged.
a) Which ends up with more electrons than normal, the comb or the hair?
b) Why does the hair become positively charged?
Q7. a) Give an example of where electrostatic charge might be a hazard.
b) How can the build-up of electrostatic charge be prevented?
Q8. In the diagram below, a charged rod is held close to a metal can. The can is on an insulated stand.

a) Draw in any induced charges on the can.

b) Why is the can attracted to the rod even though the net charge on the can is zero?
c) If you touch the can with your finger, electrons flow through it. In which direction is the flow?
d) What type of charge is left on the can after it has been touched?
Q9. Static electricity is useful in spraying paint.
a) Write down two uses of static electricity.
b) Explain how static electricity works in spray painting. What is the advantage of this technique?
c) The paint spreads out as it emerges from the spray gun, why?
Q9. Two charged balls are hung side by side. They settle as shown. What can you say about the charges on the balls?

Q10. a). A girl rubs a Perspex ruler on her sleeve. He holds it near water flowing from a tap. The water moves
towards the ruler. Explain?
b). What difference would it make if the ruler were made of polythene?

Page 127
Q11. Use words from the list below to complete the following sentences. You can use them mire than once.
attract(s) duster electrons insulators like negatively opposite positively protons
repel rod
A polythene rod is rubbed with a duster. ____________ leave the ____________ and move to the ______________. The
polythene becomes ______________ charged and the duster ____________ charged.
Conductors allow ______________ to travel through them but __________ do not.
A positively charged object attracts tiny pieces of paper to it. It __________ electrons in the paper. This leaves the surface
of the paper _____________ charged. They stick together because ________ charges ___________.
Q12. Fig. 12.1 shows two positively charged conducting spheres mounted on rods made of a good electrical
insulator.

Fig. 12.2 shows a section through oppositely charged parallel plates.

a) Draw the electric field pattern on each diagram.

b) Give an example of a suitable for i) the spheres and ii) rods in fig 12.1.
Q13. Three hollow copper spheres are placed near each other in air. The large sphere carries a positive charge
and the two small spheres touch each other, as shown in Fig. 13.1.

Fig. 13.1
The two small spheres are pulled apart, using their insulated handles, and then taken well away from the large sphere, as
shown in Fig. 13.2.

Fig. 13.2

a) The charge on the large sphere has been drawn in for you. On Fig. 13.1 and fig. 13.2 draw in the charges, if
any, on each of the smaller spheres.
b) Explain why energy is needed to separate the two small spheres.

a) i. Explain carefully why S is first attracted towards C.

ii. Explain why S is repelled after touching the surface.
b) On Fig. 141.2 mark and label each force acting on S.
c) When a Bunsen flame is passed beneath S, the sphere falls back towards C. Suggest why this happens?

16.2.0 CURRENT ELECTRICITY

16.2.1 ELECTRIC CURRENT: The amount of charge passing through a given point in a conductor per unit time
OR
The rate of flow of charge in a circuit.
Current = charge/time

Page 128
 I = Q/t
Q = It

------------------------->Coulomb’s law
SI unit : ampere/amp (A)
Other units: milliamps (mA), microampere (μA), kiloampere (kA)
Current is measured using an ammeter. Small quantities of current can be measured using a milli-ammeter. When the
ammeter is used, it should be connected in series with the component through which the current is to be measured.

16.2.2 ELECTROMOTIVE FORCE (E.M.F)

A cell is a source of electric current. The cell drives the charge around the electric circuit. In doing this energy is used up.
Electromotive force is the measure of the energy dissipated (used) by a source to drive a unit charge around a complete
circuit. Energy dissipated can also be described as work done.
e.m.f = work done per unit charge
e.m.f = W/Q
The SI unit of e.m.f is a volt (V). A battery with an e.m.f of 1 volt (1 V) gives 1 J of energy to a coulomb of charge which it
drives around a circuit.
1 V = joule/coulomb
1 V = J/C
USING A VOLTMETER TO MEASURE E.M.F
To measure the e.m.f of a cell or a battery of cells, connect a voltmeter in parallel with the cells without any other
components in the circuit. This kind of connection is known as open circuit. The red (+) terminal of the voltmeter is
connected to the +ve of the battery and the black (-) terminal of the voltmeter to the –ve terminal of the battery.

16.2.3 POTENTIAL DIFFERENCE (P.D)/VOLTAGE

- The work done in moving a unit charge between two points of different electric potential in the external circuit
OR
- The amount of the electrical energy being transferred to other forms when a charge flows through a component in
the external circuit.
Potential difference is also known as voltage.
Potential difference (p.d) = work done/charge = energy transferred/charge
V = W/Q or V = E/Q
P.D is also measured in volts (V)

Page 129
In an electric circuit, chemical energy in the battery is converted into electrical energy in the electrons. Some of this energy
is used up in passing through the lamp. Therefore there is p.d across the lamp.
The p.d is measured with a voltmeter. The voltmeter is connected in parallel across the components of the circuit where we
want to measure the potential difference.

Voltmeters must not be connected in series with other components in a circuit or else it will change the current through the
circuit because they have very high resistance. On the other hand the ammeters, which are connected within the circuit,
must have very low resistance

16.2.4 RESISTANCE
- Is the measure of the ability of a conductor to oppose the flow of current/ electrons.
- Current can pass easily through components with a low resistance but it cannot flow easily through components
with a high resistance (very good conductors have almost no resistance and insulators have extremely high
resistance)
- All electrical components have a certain amount of resistance.
- Resistance (R) is measured in ohms (Ω), kilohms (kΩ), megaohms (MΩ)
FIXED RESISTORS
- Are special components (materials) designed to have a certain resistances. They are used to control the amount
of current in a circuit.

RESISTOR COLOUR CODE

Resistors are colour coded to show their resistance. This consists of three or four coloured bands around the resistor. The
first three bands indicate the value of the resistance in ohms. Bands 1 and 2 are the digits of the value, and band 3
represents the number of zeroes following the first two digits. The fourth band on the resistor shows the tolerance of the
stated value.

Page 130
*NOTE:
• To decide which is the first, remember that the fourth band, if present, will either be gold or silver (or on rare
occasions pink)
• The following may help you to recall the colour codes and their values;
(Bad Boys Rape Our Young Girls But Violet Gives Willingly) OR
0 1 2 3 4 5 6 7 8 9
(Black Birds Roaming On Your Garden Bring Very Great Woes)
VARIABLE RESISTORS

The resistance of a variable resistor is not fixed. It can be changed or set to different values. They are used in circuits when
the current through the circuit needs to be varied.
A rheostat is a variable resistor consists of a coiled length of resistance wire with either end attached to a terminal. A third
terminal is attached to a sliding contact which can be moved along the length of the coil. By moving the sliding contact along
the coil, the amount of wire through which the current passes can be changed and hence the resistance changes.

MEASUREMENT OF RESISTANCE

The resistance of a conductor can be found using a voltmeter and an ammeter. A conductor of unknown resistance is
connected in series with an ammeter and a rheostat which is used as a variable resistor. The voltmeter is connected across
the ends of the conductor.
The rheostat is altered to give a series of different values of I and corresponding values of voltage.
VOLTMETER READING V(V) AMMETER READING I (A) V/I (V/A)
1.6 0.12 13.3
1.7 0.14 12.1
1.9 0.16 11.9
2.2 0.18 12.2

Page 131
 2.6 0.20 13.0

GRAPH OF VOLTAGE V (V) AGAINST CURRENT I (A)

The graph is straight line passing through the origin (0,0). This indicates that the voltage and current are directly proportional
to each other. The gradient of graph is constant and it represent the resistance of the conductor.
The ratio V/I = a constant. The value of the constant is equal to the resistance of the conductor.
Gradient = R = ∆V/∆I
R = V2 – V1/ I2 – I1
R = V/I ---------------------> OHM’S LAW

OHM’S LAW
Ohm’s law defines the relationship between the voltage across a component, the current flowing through the component and
the resistance of the component.
The ohm’s law states that;
“the amount of electric current passing through a conductor is directly proportional to potential difference
provided the temperature and other physical quantities remain the same”
V α I ; R = a constant
V = IR -------------------------------------------> ohm’s law
It can also be expressed as:
I = V/R OR R = V/
RESISTANCE, LENGTH AND CROSS-SECTIONAL AREA-resistivity
The resistance of a conductor is directly proportional to its length and inversely proportional to its cross-sectional area. This
means when the length is doubled, the conductor will double its resistance but when its cross-section is doubled its
resistance will be halved.
Therefore;
• Short and thick conductors have low → R α l/A
resistance → R = ρl/A where R = resistance in Ω
• Long and thin conductors have high ρ= resistivity in Ωm
resistance l = length in metres (m)
Mathematically; A = cross-section area in
R α l and R α 1/A m2
Examples
#1. Find the resistance of an aluminium conductor 200 m long with a cross-section area of 4 mm2 (ρ for Al is
2.83 x 10-8 Ωm)
Answ;
Data
l = 200 m A = 4 mm2 = 4 x 10-6 m2 ρ = 2.83 x 10-8 Ωm R = ?
R = ρl/A
= (2.83 x 10-8 X 200 m)/4 x 10-6
= 1.42 Ω
#2. A wire of length 0.40 m and a diameter 0.60 mm has a resistance of 1.5 Ω. Find the resistivity of the
material it is made of.
DATA
l = 0.40 m d = 0.60 mm = 0.0006 m R = 1.5 Ω ρ = ?

R = pl/A

Page 132
ρ = RA/l A = πr2 = π(d2/4) = π(0.0006 m)2/4 = 2.8 x 10-7 m2
= 1.5(2.8 x 10-7)/0.40
= 1.06 x 10-6 Ωm

INTERNAL RESISTANCE
The energy supplied per unit charge is not all used in the external circuit. There is some energy which is needed to
overcome the internal resistance and drive the charge across the battery or cell.

In above diagram, the voltage drop across the resistor will be less than the e.m.f. This is because some energy has been
used to drive the charge through /across the cell.
The internal resistance of the cell is given by:
r = (E – V)/I

Where E= e.m.f
r = internal resistance of the cell
I = current
→ E – V = Ir
E – IR = Ir
E = IR + Ir
E = I(R + r); where R = external resistance
PROBLEMS
#1. A cell of unknown e.m.f (E) and internal resistance of 2 Ω is connected to a 5 Ω resistor. If the terminal p.d
(V) is 1.0 V, Calculate the e.m.f of the cell?
= 0.2 A
Data THEN E = I(R + r)
R=5Ω r = 2 Ω V = 1.0 V I = ? E=? = 0.2 A(5 Ω + 2 Ω)
I = V/R = 1.4 Ω
= 1.0 V/5 Ω
#2. A battery of e.m.f 4.0 V and internal resistance of 5 Ω is connected to a resistor of 1.5 Ω. Calculate the
terminal p.d.
Answer.
Data
E = 4.0 V r=5Ω R = 1.5 Ω V=?
I = E/(R + r) = 4.0/(1.5 + 5) = 0.6 A
V = E – Ir
= 4.0 – 0.6(5)

= 1.0

16.2.5 I/V GRAPHS – Graphs showing the relationship of current and voltage drop across a
conductor.
1) Ohmic conductors
The current through the conductor is directly proportional to the voltage across the ends of the conductor provided the
temperature and other physical properties are constant – OHM’S LAW
The graph is a straight line.

Page 133
 The inverse of the graph here is equal to the resistance of the conductor.
2) Non – ohmic conductors
They are conductors which do not obey the ohm’s law

a) Diode
Voltage is not proportional to current

Curve getting steeper- therefore the resistance decrease with increase in current.
Note: if the voltage is increased in the other direction, the current will be almost zero since a diode allows the
current to flow only in one direction. This means a diode has a small resistance when connected in one way
but a very large resistance when the voltage is reversed.
b) Filament lamp
Filament lamps or light bulbs are designed to produce light and therefore heat. Any current passing through
the filament will make it hot and increase its resistance. A light bulb is therefore non-ohmic for the whole
range of possible currents

The graph bends over as V and I increase. Then this means the gradient (I/V) decrease and hence the
resistance (V/I) increases and makes the filament hotter.

c) Thermistor
A thermistor is an electrical component which is used in temperature-operated circuits such as the circuits
used to control air conditioning units. It is a non-ohmic resistor, its resistance decreases as the current
increases.

The graph bends up, this means the inverse of the resistance (I/V) increase and therefore the resistance (V/I) decreases.
LIMITATIONS OF THE OHM’S LAW
Under normal working conditions a resistor is ohmic, its resistance does not depend on the current or voltage applied to it. If
too much current flows through the resistor, it will become hot and its resistance will start to increase. This resistor has
become non-ohmic
Therefore, in general, when the temperature increase the resistance of metals will also increase. The resistance of some
conductors will also change when they are bent or placed under pressure.

Page 134
16.2.6 QUESTIONS
a). What is the resistance of its element?
b) Why does the element need to have resistance?
Q4. A 6 V supply is applied to 1000 Ω resistor. What current will flow?
Q5. Use ohm’s law to calculate the following:
a) The voltage required to produce a current of 2 A in a 12 Ω resistor.
b) The voltage required to produce a current of 0.1 A in a 200 Ω resistor.
c) The current produced when a voltage of 12 V is applied to a 100 Ω.
d) The current produced when a voltage of 230 V is applied to a 10 Ω resistor.
e) The resistance of a wire which under a potential difference of 6 V allows a current of 0.1 A to flow.
f) The resistance of a heater which under a potential difference of 230 V allows a current of 10 A to flow.
Q6. Explain clearly the difference between electromotive force of a cell and potential difference across a lamp.
Q7.a) If the current through a floodlamp is 5 A, what charge passes in i) 1 s ii) 10 s iii) 5 minutes?
b) What is the current in a circuit if the charge passing in each point is i) 10 C in 2 s, ii) 20 C in 40 s iii) 200 C
in 2 minutes?
Q8. The p.d across the lamp is 12 V. How many joules of electrical energy are changed into light and heat
when:
i). A charge of 1 C passes through it
ii). A charge of 5 C passes through it

16.2.7 ELECTRIC CIRCUIT

Some circuit symbols used for different components:

Page 135
Series circuit
Components are in series when they are connected into a continuous line, end to end such that the same current flows
through each component

i) The current that flows through components in series is the same and equal at each and every point.
ii) All the components will share the e.m.f. according to their resistances. The largest voltage drop will be
across a component with the largest resistance. The sum of the potential difference in series circuit is equal
to the terminal potential difference across the source.

VE = V1 + V2 + V3........ ------------> (1)

V1 = IR1 V2 = IR2 VE = IRTOTAL
iii) Resistance in series

From ohm’s law: V =IR IRT = I(R1 + R2 + R3)

Then equation (1) above can be modified: Divide by I
VE = V1 + V2 + V3 IRT/I = I(R1 + R2 + R3)/I
IRT = IR1 + IR2 + IR3
RT = R1 + R2 + R3 ---------------> Total/combined/effective resistance for resistors in series

PARALLEL CIRCUIT
Components are in parallel when they are displayed side by side and their corresponding ends joined.

i) The branches will share the main current I according to the resistance of each branch. The largest
current will flow through a branch with the smallest resistance. The sum of the current through the branches
is equal to the main current.
I = I1 + I2 + ........ ----------> (2)
ii) The potential difference across the components connected in parallel is equal and also the same as the
terminal difference across the source.

iii) Resistance in parallel resistors

Page 136
 Equation can be modified:
I = I 1 + I2 + I3
From ohm’s law
VE/RT = V1/R1 + V2/R2 + V3/R3; Remember: VE = V1 = V2 = V3
V/RT = V/R1 + V/R2 + V/R3
Factorise and then divide by V
V/RT = V(1/R1 +1/R2 + 1/R3)
1/RT = 1/R1 + 1/R2 + 1/R3
-------> effective/total/combined resistance for parallel resistors
*For two parallel resistors:
1/RT = 1/R1 + 1/R2
1/RT = R1 + R2/R1R2
RT = R1R2/R1 + R2
RT = Product of resistance/sum of resistance

16.2.8 ELECTRICAL ENERGY

When electrons flow through any component, some of their stored electrical energy is released in (converted to) different
forms:
e.g
• light bulb: electrical energy ------------> light and heat
• kettle: electrical energy --------> heat
• resistor: electrical energy -------> heat
How to calculate the amount electrical energy converted to other forms (or consumed) by an electrical appliance:
Recall: The amount of electrical energy being transferred to other form(s) when a unit charge flows through a component
(appliance) in a circuit is called the potential difference (voltage).
From the definition it follows;
Voltage (p.d) = Energy transferred/Charge
Energy = Voltage x Charge
E=VxQ
Remember that Q = It ----------> ohm’s law
Then
E = VIt

SI unit of electrical energy: joule (J)

Other equations;
i. E = I2Rt
ii. E = (V2/R)t
iii. E = Pt
16.2.9 ELECTRICAL POWER
The amount of electrical energy a component converts into other forms every second is called its (electrical) power
Or
Electrical power is defined as the rate at which electrical energy is converted into other forms.
Power = Energy converted/time taken
P = E/t
P = VIt/t
P =VI

SI unit of electrical power: watt (W)

1 W = 1 J/s

Page 137
 Other equations that can be used to calculate electrical power:
Recall the ohm’s law; V = IR
i) I = V/R ii) V = IR
THEN P = V(V/R) We can have P = (IR)R
P = V2/R P = I2 R
Examples
#1: A 240 V, 5 A kettle takes 5 minutes to boil 1 L of water.
a) What energy change occurs in the kettle?
b) What is the electrical power of the kettle?
c) How much electrical energy is converted into heat by the kettle in 5 minutes?
ANS:
a) Electrical energy --------> heat energy
b) Data; V = 240 V, I =5 A, P=? = 240 V x 5 A
P =VI = 1200 W
c) Data; V = 240 V, I = 5 A, t = 5 minutes =330 s, P = 1200 W, E =?
E = VIt E = Pt
= 240 V x 5 A x 330 s OR = 1200 W x 330 s
= 396 000 J = 396 000 J
#2: A 220 V, 10 A electric motor takes 20 seconds to lift aload of bricks to the top of a building 15 m above the
ground. Each brick has a mass 0f 1.5 kg.
a) What energy changes occur as the bricks are lifted?
b) How much electrical energy is supplied to the motor in 20 seconds?
c) Assuming the motor is 100 % efficient, how many bricks can be lifted in a single load?
Ans:
a) Electrical energy ----------> gravitational potential energy
b) Data; E =?, I = 10 A, V = 220 V, t = 20 s
E = VIt
= 220 V x 10 A x 20 s
= 44 000 J
c) Total electrical energy converted = total GPE
44 000 J = mgh
44 000 J = 15 m x 10 N/kg x total mass m of bricks
m = 44 000 J/15 m x 10 N/kg
m = 293 kg
number of bricks = m/mass of a single brick = 293 kg/1.5 kg
= 195 bricks

16.2.9 DOMESTIC ELECTRICITY

Electricity available in household circuits originates from a generator in a power station. Electricity is supplied to our homes
through two cables (wires); Live and neutral. The current flowing through these cables is alternating current (a.c) with a
frequency of 50 Hz. This means that the current in which the current flows reverses 50 times every second. The electricity
cables are connected to the terminals in wall sockets.
1. Live wire (brown or red) – carries the alternating current to the appliance. It supply supplies electricity at a
voltage 240 V. Since the supply is a.c. at 50 Hz, the voltage varies between positive and negative (+240 V and -
240 V) 50 times a second. This causes the current to flow to and fro through the circuit.

Page 138
2. Neutral wire (blue or black)- completes the circuit by providing the return path to the supply (or mains). The
neutral wire is earthed at the electricity substation, therefore it is at 0 V
*Although the neutral wire carries electric charge there is no danger of electric shock if it is touched
since it is at the same potential as a person who stands on the floor.

3. Earth wire (green and yellow) or (green)- this wire is for safety purposes. One end of the Earth wire is connected
to the metal case of the appliance. The other end is connected via the wall sockets and metal pipe to Earth box outside
the house.

The earth wire provides a path of almost zero resistance from the case of the appliance to the earth. If the live wire
accidentally touches the metal case of the appliance, a large current will flow through the earth wire and the fuse melts,
isolating the appliance.

Page 139
 Without an earth wire, the case would become live anyone touching it would receive a dangerous shock.

FUSES (& CIRCUIT BREAKERS)

Function: to prevent excessive current to flow through an appliance. Too high current may cause some electric fire or
accident.
Fuse is a wire made from a metal with a low melting point. If a fuse is part of a circuit, it will eventually melt if the current is
too excessive and the circuit will break. But excessive current may flow through an appliance even if a fuse there if a short
circuit is present.

Page 140
*Fuses must be connected into the live wire. This ensures that when the fuse melts, the appliance is no longer “live”.
Fusing Rating
Fuses are rated according to the amount of current required to melt/blow it. E.g. 1 A fuse will melt if a current of 1 A flows
through it, a 5 A fuse will melt if a current of 5 A flows through it, etc. Fuse rating are always whole number integers. The
plugs are usually fitted with either 3 A, 5 A or 13 A.
It is vital that the correct fuse is installed into an appliance. The fuse rating should be greater than the normal operating
current of appliance, but as close to it as possible- so that the fuse will be blown as soon as the current gets too high.
Example
An electrical kettle is labelled 230 V 2300 W. Work out whether a 3 A, 5 A or 13 A fuse is needed.
Ans: First, calculate the normal operating current
P = 2300 W V = 230 V I = ? I =2300 W/230 V
P = VI = 10 A
If the normal operating current is 10 A, a 13 A fuse should be fitted.
#2 DVD PLAYER: 100 W, 240 V
I = 100 W/240 V
= 0.4 A
So a 3 A fuse is ideal.
*Note: 1) The DVD player would still work with a fuse of 13 A. But if a fault develops, the current will continue
to flow without the fuse blowing and this might cause the appliance to overheat and catch fire.
2) For currents higher than 13 A, circuit breakers are used instead of fuses. Circuit breakers operate
electromagnetically and can be reset by flicking a switch (they do not have to be replaced like fuses)

THREE-PIN PLUG

Three-pin plug power point/socket

The three wires in an electrical cable of appliances are connected to a three-pin electrical plug. In such plugs the live wire
from the cable is connected to the live pin, the neutral wire is connected to the neutral pin and the earth wire is connected to
the earth pin. When the plug is inserted into a power, each pin on the plug connects with the corresponding wire in the
power point.
*It is important to ensure that wires are correctly connected in both plugs and the sockets. The power point
switch is placed in the live side of the circuit
*The sheath of the cable (not the wires themselves) is clamped to keep the connections safe (intact) if ever the
cable is pulled or tugged.
*The fuse is chosen to suit the circuit which it protects.
DOUBLE INSULATION

Symbol for double insulation.

Some household appliances, e.g. radios, have plastic cases and their cables do not have an earth wire. They have only the
live and neutral wires. There is no risk getting an electrical shock from a plastic case since plastic is an electrical insulator.
This is described as double insulation because:
• The live and neutral wires are covered in an insulated sheath,
• The appliance itself is covered by an insulated case.

FEATURES OF A HOUSE CIRCUIT-

Page 141
a) PARALLEL CIRCUITS:- House circuits e.g. lights are connected in parallel so that appliances receive the full
mains supply of 240 V and also that they can operate independently (e.g each bulb can have its own switch and
also if one bulb breaks, the others will remain on unlike in a series circuit where all would turn off).
b) SWITCHES AND FUSES:- are always connected in the live wire. If they were connected in the neutral wire, the
appliance would remain ‘live’ even when the switch is off or the fuse is blown
c) STAIRCASE CIRCUIT:- The light is controlled from two places by the two-way switches.
d) RING MAIN CIRCUIT:- the wiring system in which the live and neutral wires run in two complete rings/loops round
the house and the power sockets each rated at 13 A, are tapped off from them

SIMPLIFIED RING MAIN.

Page 142
USES OF ELECRICITY
1. Lighting
• Filament lamp – has a small coil of tungsten wire which becomes hot when current flows through it.
• Fluorescent lamp – current is passed through mercury vapour which emits ultraviolet light which in turn
makes the powder on the glass give out visible light.
2. Heating:- heating elements are made from nichrome wire which has a high resistance. Heating elements are used
in electric fires, kettles, irons, cookers, ovens, etc.
3. Machines:- electric machines such as drills, saws, lawn-mowers, cassette recorders, fans, washing machines, etc
all use electric motor which is operated by electricity.
4. Communications:- there are various electric powered communication devices, e.g. telephone, cell-phone, fax,
radio, television, telex, computer, etc.
5. Security: many security systems such as smoke sensors, automatic gates, remote controlled locks, burglar alarm,
etc operate on electricity.
COST OF ELECTRICITY
Electrical metres (joule-meter) are included in our houses to measure the amount of electrical energy consumed by the
household. The household is charged for the electrical energy they consumed. Electricity supply companies (e.g. B.P.C)
measure electrical energy consumed in kilowatt-hours (kWh) or simply ‘units’.
1 kWh = 1 unit
1 kWh is the measure of the amount of the electrical energy consumed for 1 hour (3600 s) at the rate of 1 kW (1000 W) or
the energy used by an appliance rated 1 kW in 1 hour.
i.e. 1 kWh = 1000 W x 3600 s
= 1000 J/s x 3600 s
= 3 600 000 J
1 kWh = 3.6 MJ

cost of electricity = total electrical energy consumed in kWh x cost per kWh

Example:
a) How much energy is used by a 3 500 W heater which is on for 30 minutes
b) How much will it cost to run the heater if one unit of electricity costs 5 thebe
Ans:
a) P = 3500 W (3.5 kW), t = 30 minutes b) E = 1.75 kW, cost per kW = 5 thebe
(1/2 h), E=? Total cost = E x cost per kW
E = Pt = 1.75 kW x 5 thebe/kW
= 3.5 kW x ½ h = 8.75 thebe
= 1.75 kW or 1.75 units = P0.09
ELECTRICAL HAZARDS AND DANGERS

Page 143
 1. DAMP CONDITIONS: Water can conduct current. And also our bodies’ resistance is lower if it is wet and hence a
great amount of current will flow through it. Therefore if electrical equipment gets wet or touched with wet hands,
there is a risk someone being electrocuted (getting an electric shock).
2. OLD, FRAYED WIRING AND DAMAGED INSULATION:- broken strands mean a wire will have a higher
resistance at one point. When current flows through it, there might be more heat produced, enough to melt the
insulation and cause a fire.
Damaged insulation can cause ;i) an electrical shock to a person touching the exposed ‘live’ wire, and ii) a short
circuit if the bare wires touch.
SHORT CIRCUIT: results if the ‘Live’ wire touches the neutral wire. The current by-passes the appliance and the
current can increase to such a high value that it can cause an electric fire especially if there is no fuse.

To prevent this, always inspect your cords more frequently and replace worn or damaged cables.
3. OVERHEATING OF CABLES: caused by passing a high current on a wire designed for a low current.
Overheating can cause the insulation to melt or burn and can cause fires.
4. OVERLOADING OF SOCKETS: connecting many appliances in one socket can lead to overheating of
5. cables and hence cause electric fires.

FINDING A FAULT
When an appliance stops working it may be due to a fault that is easy to rectify. Before calling a technician it is wise to try to
diagnose the fault.
You may follow the steps below;
1. Check that the appliance is switched on.
2. Check that the power is on. Do other appliances work?
3. Check the fuse. If it is blown, replace it. If the new fuse blows, check for a short circuit.
4. Check that the plug is correctly connected, with no loose wires or untidy strands of wire sticking out.
5. Check that the cable connection to the appliance is firm.
6. Check that the insulation is in good condition. If it looks worn or torn replace it with a similar cable.
*NB:- If after checking all the above, the appliance is still not working, engage a trained technician

16.2.11 QUESTIONS
Q1. What is meant by the statement ‘the e.m.f. of a battery is 12 V’? When the battery is in use, the
p.d. between the terminals is found to be 11.5 V. What reasons might there be for that?
Q2. An electric heater has a label attached to it, as shown below.
Explain the meaning of the following terms used on the label; (i) 240 V (ii) 50 Hz (iii) power: 2 kW.
Q3. You have a selection of fuses available: 1 A, 2 A, 3 A, 5 A, 7 A, 10 A, 13 A. Which would be the most suitable
fuse for (i) a TV set labelled 230 V, 140 W, (ii) an electric fire labelled 230 V, 2 kW, (iii) a kettle labelled V,
750 W?
Q4. An electric motor is raising a load of weight 5000 N at a steady speed of 0.5 m/s. The motor works from a
250 V supply. How much work is done in 1 second?
Q5. A 720 W kettle boils some water in 10 minutes. How much will this cost if 1 unit of electricity is charged at
10 thebe? How long will a 60 W lamp run for the same cost?
Q6. a)Why should wires with damaged insulation be replaced?
b) Often, the plug used to connect an appliance to a wall socket has a fuse fitted inside it. Explain the
reason for this.
c) An appliance which has metal parts, for example an electric kettle, should be earthed. Explain why this
should be done.
d) In some countries it is illegal to have power sockets in a bathroom, to stop you using hairdryers. Why
would it be foolish to use a hairdryer near to a washbasin?
Q7. The diagram below shows the inside of a three-pin plug.

Page 144
 a). What is the name of pin A?
b) What is the name of pin B?
c) What is the colour of the wire connected to the Earth pin?
d)What is D?
Q8. If electrical energy costs 7 thebe per kWh, calculate the cost of the following:
a) a 3 kW fire turned on for 6 hours
b) a 1.2 kW hair drier for 30 mins
c) a 100 W bulb for 10 hours.
Q9. A student using the circuit shown below investigates the relationship between the current flowing through
a resistor and the p.d. across it.

a) What is A?
b) What is B?
c) What is C?
d) What is D?
The student’s results are shown in the table below.
p.d./V 0 2 4 6 8 10 12
current/A 0 0.25 0.50 0.80 1.00 1.25 1.50

e) Plot a graph of p.d. against current.

f) Which result appears to have been measured incorrectly?
g) What is the resistance of the resistor R?
h)
Q10. A number of 8 Ω resistors are available. Draw diagrams to show how you could connect a suitable
number of these resistors to give an effective resistance of (a) 24 Ω (b) 4 Ω (c) 18 Ω

Q11. An electric lamp is marked 250 V, 100 W and an immersion heater is marked 250 V, 2 kW.
a) Calculate the current in each device when operating normally.
b) Explain why the filament of the lamp is made to have a larger resistance than the heating element of the
immersion heater.
c) Suggest a reason why the filament is made of a metal with a much higher melting point than that of the element.
d) The heat capacity of the filament of the lamp is very small. State one reason why this is an advantage.
e) Explain why the wire connecting the immersion heater to the supply remains cool even when the heater has been
in use for some time.
Page 145
16.3.6 MAGNETIC EFFECT ON A CURRENT-CARRYING CONDUCTOR.
A wire carrying electric current generates a magnetic field around itself.
a) Magnetic field around a wire
If a current is passed through a straight wire, it produces a weak magnetic field as shown below.

Rule for field direction: the right-hand screw rule- Imagine gripping the wire with your right hand so that your thumb points
in the direction of the current. Your fingers then point in the direction of the field.

NOTE:
i). The field lines are in circles.
ii) The field lines are shown closest together near to the wire, because the field is strongest there, and lines get
further apart away from the wire where the field is weaker.

Page 146
iii). If the current is increased, the field is made stronger.
iv). If you reverse the current direction, this reverses the field.
b). Field due to a circular coil
The field lines pattern is as shown below;

c). Field due to solenoid

The magnetic field produced by a coil has these features:

a). The field is like that around a bar magnet, with magnetic poles at the ends of the coils.
b). If you increase the current, this makes the field stronger.
c). If you put more turns on the coil, the field is stronger
d). If you reverse the current direction, this reverses the field.
Rule for poles: Imagine gripping the coil with your right hand so that your fingers point the same way as the
current, your thumb then points towards the N pole of the coil.
*NB: when using the rules described above, remember that:-
a). the current direction is from the + to the – (use the conventional current)
b). the magnetic field direction is the direction the N end of a compass needle would point.

16.4.0 MOTOR EFFECT

If a wire that is carrying an electric current is put in a magnetic field, the wire experiences a sideways force and moves. This
effect is used to make the electric motor work in devices such as loudspeakers, electric drill, etc
Demonstration
A flexible wire is supported in the strong magnetic field of a C-shaped magnet. When the switch is pressed, current flows in
the wire which jumps upwards.

Page 147
Explanation: when a current flows through the coil of wire, it creates a magnetic field, which interacts with the field
produced by the two permanent magnets. The two fields exert a force that pushes the wire at right angles to the permanent
magnetic field.

The field lines due to the wire are circles and their direction is as shown above. The dotted lines represent the field lines of
the magnet and their direction. The resultant field of the two fields is as shown in the diagram b. There are more lines below
than above the wire since both fields act in the same direction but in opposition above. If you imagine that the lines are like
stretched elastic, those below will try to straighten out and in so doing will exert an upwards force on the wire.
To increase the strength of the force;
i). Increase the current
ii). Usea stronger magnet
iii). Increase the length of wire in the field.

If you reverse either the current or the field, the force is reversed
Fleming’s left hand rule:
This is the rule used to work out the direction of the force or thrust on the wire. It works like this:
Hold the thumb and the first two fingers of your left hand at right angles. The First finger is pointing in the direction of the
Field and the seCond finger in the direction of Current, then the Thumb points in the direction of the Thrust(Motion).

(When using this rule, remember that (i) the current direction is from + to – and the field lines run from N to S.)
Examples:
1.

Page 148
2.

3.

4.

5.

6.

7.

Page 149
8.

16.4.1 SIMPLE D.C ELECTRIC MOTOR

a). It works from the direct current (d.c.) and consists of a rectangular coil of wire mounted on an axle which
can rotate between the poles of a C-shaped magnet.
b). Each end of the coil is connected to a half of a split ring, called the commutator, which rotates with the coil.
c) Current passes into the coil via two brushes which are pressing against the split ring. When the current flows
through the coil, forces are set up on the two sides of the coil labelled ab and cd since they are at right
angles to the field. According to the Fleming’s left-hand rule, the two forces, equal in magnitude but
opposite direction, form a couple and produce a turning effect that causes the coil/loop to rotate.
d) When the coil reaches the vertical position, the brushes are in line with the gaps in the commutator and no
current flows for a moment. But the inertia keeps the coil rotating to overshoot the commutator halves and
change contact from one brush to the other. This reverses the current as well as the directions of the forces
on the two sides. This helps the coil to rotate in one direction (either clockwise or anticlockwise)
The turning effect on the coil can be increased by:
a). increasing the current
b). using a stronger magnet
c). increasing the number of turns on the coil
d). increasing the area of the coil.
16.4.2 Practical motors
- They have several coils with each set at a different angle and each with its own pair of commutator pieces.
This increases the turning effect and also gives a smoother running.
-The coils contain hundreds of turns of wire wounded on a iron core called armature. The armature gets
magnetised and increases the strength of magnetic field
-The poles of the magnet are curved to create a radial magnetic field. This keeps the turning effect at
maximum for most of the coil’s rotation.

16.4.3 Moving-coil loudspeaker

Page 150
In the loudspeaker, the magnet is specially shaped so that the wire of the coil is at the right angle to its radical field. The
loudspeaker is connected to an amplifier which gives out an alternating current, this current flows backwards, forwards,
backwards, .......... and so on, causing a force on the coil which is also backwards, forwards, backwards....... All these cause
the cone to vibrate and creates sound waves.
16.4.4 Microphone
The moving-coil microphone contains a thin metal foil diaphragm. There is a small coil attached to the rear of the diaphragm.
This coil is situated in a magnetic field provided by a cylindrical permanent magnet. Sound waves cause the diaphragm and
coil to vibrate. As the coil moves in the magnetic field a current is induced in it. This varying current can be amplified and
heard in a loudspeaker.

16.4.5 Moving-coil meters

Meters for measuring current and voltage frequently have a coil which is pivoted in a magnetic field.
a). Current enters and leaves the coil by hair springs above and below it.
Page 151
b). When current flows, it produces a magnetic field that would interact with the field due to the permanent
magnet. This would produce a couple on the coil (as in an electric motor) and cause it rotate and turns
along with the pointer attached.
c). As the coil turns and twist the spring, the springs would try to stop the coil turning. The coil turns until the
turning effect of the forces due to the current balance the turning effect of the spring. The greater the
current in the coil, the coil would turn further and the greater the deflection shown by the pointer.
d). The soft-iron cylinder/drum produces a radial magnetic field which makes the coil deflection proportional
to the current and this gives a linear scale.

16.4.6 QUESTIONS
Q1. Give three examples of actions that cause an induced e.m.f to be set up in a coil of wire.
Q2. Fig. 2.1. shows a magnet being pushed into a coil of wire, which is connected to a galvanometer. Which of
the following statements is/are correct?

Fig. 2.1
a) The induced current will flow from A to B through the coil.
b) The induced current will flow from B to A through the coil.
c) No induced current will flow.
d) End B will become a north pole.
Q3. A magnet is used to induce a current in a coil of wire. List three things that could be done to increase the
current produced.
Q4. Fig. 4.1 shows a conductor AB in a magnetic field. Mark in the direction of the magnetic field. Which
direction will current be induced in the conductor AB when it is moved:
(a) Into the page
(b) Out of the page?

Fig. 4.1.

Q5. i) The diagram below shows a bar magnet, and a coil of wire connected to a sensitive ammeter.

As the magnet was pushed slowly into the coil the ammeter pointer moved 10 divisions to the right.
What would you expected to happen

Page 152
 a) If the magnet is pulled slowly out of the coil?
b) The magnet is held stationary inside the coil?
c) The magnet is turned around so that its north pole is nearer the coil. The magnet is then pushed quickly into the
coil?
d) Explain in your own words why the ammeter deflects.
ii) The diagram shows the direction in which a galvanometer needle is deflected when a magnet is moved
towards a coil. The size of the arrow represents the speed at which the magnet is moved.

Show the position of the galvanometer needle in each of the following cases:

Q6. Fig. 6.1. shows a structural diagram of bicycle dynamo. Study the diagram and answer the following
questions:

a) What turns the driving wheel of the dynamo?

b) What is connected to the output of the dynamo?
c) Briefly explain how the dynamo produces current.
d) How could the output of the dynamo be increased?
Q7. Draw a sketch graph to show how the EMF of a simple a.c. generator varies with time over two full
revolutions. Relate the positions of the coil to the values shown on your graph.
b) draw a second sketch graph showing what you would expect if the speed of rotation of the coil were
doubled.
c) i. Describe the main difference in the construction between a d.c dynamo and an a.c dynamo.
ii. Sketch a graph to show how the current generated by a d.c dynamo varies with time. How would the
output change if a coil with twice as many turns were used?

Q8. The filament of table lamp is connected to a 250 V, 50 Hz mains supply by two wires. One wire is the live
wire and the other is the neutral.
a) Use the axes in Fig. 8.1 to sketch a graph which shows the variation with time of the voltage of the live wire during
one cycle. The zero of the voltage scale is earth voltage.

Page 153
 Fig. 8.1

b) On the axes in Fig. 8.2 show the corresponding variation of voltage of the neutral wire.

Fig. 8.2
Q9. Fig. 9.1 shows the essential parts of a moving-iron ammeter.

Fig. 9.1
a) Explain why the needle deflects when a steady current passes through the coil.
b) Explain why the direction of the deflection is unchanged when the direction of the current is reversed.
c) State and explain what would be observed when the steady current is replaced by an alternating current with a
frequency of 50 Hz.

The coil of an ammeter has a resistance of 0.5 Ω. A resistor of resistance 0.25 Ω is connected between the terminals of the
ammeter, and a current of 2 A passes as shown in fig. 9.2

Fig. 9.2
d) Calculate the effective resistance of the coil and the resistor when connected as shown in f.g. 9.2.
e) Calculate the potential difference between the points A and B.
f) Calculate the current in the coil of the ammeter.

Page 154
16.3.0 ELECTROMAGNETIC EFFECTS
Electricity can be produced in two ways:
1) Chemical reactions: produce flow of electricity from batteries and cells. The current of the electricity produced in
this way is quite small.
2) Electromagnetic induction: this is a process of producing electricity in generators and dynamos using magnetic
fields.
16.3.1 ELECTROMAGNETIC INDUCTION.
Current is created in a wire when:
• The wire is moved through a magnetic field (cutting the field lines)
• The magnetic field is moved past the wire
• The magnetic field around the wire changes strength.
The current created in this way is said to be induced current.
1). Moving wire and a U-shaped magnet

When a wire is moved across a magnetic field, an E.M.F is induced between the ends of the wire. One end of the wire
becomes positively charged and the other end becomes negatively charged. If the wire forms part of a complete circuit, the
EMF makes (induced) current flow.
In the above diagram, first the wire is held at rest between the poles of the magnet and the galvanometer observed. The
wire is then moved in each of the six directions shown
Observations:
a. There is deflection on the galvanometer only when the wire is moving upwards (direction 1) or downwards
(direction 2) indicating flow of current in the circuit.
b. No deflection on the galvanometer when the wire is moving in other directions (3, 4, 5 & 6), showing that there is
no current induced in those cases.

c. Explanation of observations
• An EMF is induced in a conductor (e.g. wire) only when it crosses (cuts) magnetic field lines and this cause a
current to flow if the conductor is part of a complete circuit.
• There is no induced EMF or current when the wire is not moving or is moving parallel to the lines.
Direction of induced current
The direction in which the current flows through the wire depends on the following factors
a. The direction of motion of the wire
b. The magnetic field direction.
Therefore reversing the direction of motion or polarity will reverse the current direction.
The direction can be predicted using fleming’s right hand rule

Page 155
 *Hold the thumb and the first two fingers of the right hand at the right angles to each other. Then according to the fleming’s
right hand rule the First finger points in the direction of the magnetic Field, the thuMb points in the direction of the Motion
and then the seCond finger shows the direction of the Current.
The induced EMF (and current) can be increased by:
• Moving the wire faster
• Using a stronger magnet
• Increasing the length of wire in the magnetic field, e.g by looping or coiling the wire through the several times.
The above facts are summed up by Faraday’s Law. The law states that:
‘The size of induced EMF (or current) is directly proportional to the rate at which the conductor cuts the
magnetic field lines’
2). Bar magnet and coil
An EMF can also be induced in the conductor when a bar magnet is pushed in and out of a coil. If the coil is part of a
complete circuit the induced EMF (VOLTAGE) drives a current round the circuit.

When the N pole is moved into the coil, the galvanometer register current, its needle is seen to be deflected to the right.

When the magnet is held still inside the coil, the needle returns to its zero position. This shows that no current is flowing
because there is no movement therefore no magnetic field lines are being cut.

Page 156
When the bar is pulled out of the coil, the needle is deflected to the left. This shows that moving the magnet in the opposite
direction reverses the current direction.
*NB:- 1) the similar results as the above can be obtained by moving a coil of wire over a stationary magnet.
2) But if the S pole of a magnet, rather than the N pole, is used the direction of the current also reverses
and opposite results will be obtained for diagrams (a) and (b) above.
The size of the induced EMF (and hence of current) can be increased by:-
- moving the coil or magnet faster
- using a stronger magnet
- increasing the number of turns on the coil (this increase the length of wire cutting through the magnetic field).

LENZ’S LAW
The direction of the induced current through the coil can be found by using the Lenz’s law.
Lenz’s law states that:
‘The direction of the induced current is in such direction as to oppose the change producing it’.

According to the Lenz’s law, in (a) the induced current should flow in a direction which makes the coil behaves like a magnet
with its top as a N pole. Then the incoming magnet is repelled and the downward motion is opposed.
But when the magnet is removed, the top of the coil should be a S pole so that the removal of the magnet will be opposed
as the N pole is attracted and the current will thus flow in the opposite direction to that when the magnet is pushed in.
16.3.2 A simple a.c. generator (alternator)

Page 157
a). In a simple a.c. generator (alternator) the coil is rotated by the shaft.
b). the slip rings rotate with the coil. When the coil is rotated, it cuts magnetic field lines so a voltage is
generated. This makes a current flow. As the coil rotates, each side travels upwards, downwards,
upwards.... and so on through the field. So the current flows backwards, forwards..... etc. Therefore it is a.c.
c). the current passes to the outside circuit via carbon brushes which press against the side of each slip ring.
A typical graph that shows how voltage (or current) varies over one complete rotation

Note: . a). The current is greatest when the coil is horizontal because it will be cutting field lines most rapidly.
But current is zero when the coil is vertical since it will be along the field lines and no cutting
happens. Also the current will change the direction when in a vertical position.
b). increasing the speed of rotation increases the frequency of an a.c. generated. Frequency of an a.c. is
the number of complete cycles it makes in each second. For the mains supply a.c.’s frequency is 50
Hz.
The voltage (or current) from the generator can be increased by:
a). using a stronger magnet
b). increasing the number of turns in the coil.
c). winding the coil on a soft-iron armature and using a bigger coil
d). rotating the coil at a higher speed.

16.3.3 A simple d.c. generator (dynamo)

Page 158
An a.c. generator becomes a direct current one if the slip rings are replaced by a commutator (which contains two half-rings
known as split rings). The carbon brushes are arranged such that as the coil goes through the vertical, changeover of
contact occurs from one half of the split ring of the commutator to the other and the commutator reverses the voltage
induced and so one brush is always positive and the other negative. And this ensures that current to the outside circuit
always flows in the same direction.
Just like in an a.c. generator, when the coil rotates, a current is produced by electromagnetic induction and the current
passes to the external circuit through the brushes in contact with the commutator. Although the induced is d.c. it varies in
value unlike the d.c from the battery.

graph of DC generator
The current is maximum when the coil is horizontal and minimum (or zero) when the coil is vertical.
Bicycle dynamo

It uses the principles of electromagnetic induction to generate electricity in bicycles. The driving wheel of the dynamo
presses against the tyre of the bicycle. When the tyre rotates, it turns the driving wheel of the dynamo and causes a
cylindrical permanent magnet to turn as well. The turning permanent magnet reverses the magnetism through the soft-iron
core every time the coil is rotated by 180°. This change in the magnetic field through the core induces an a.c. in the coil wire
(stator coil). The size of the current produced can be increased by increasing the speed of the bicycle.

Page 159
16.3.4 MUTUAL INDUCTION
This involves the induction of current in one circuit, whenever it cuts a magnetic field produced by another circuit i.e current
induced in a circuit due to the changing magnetic field of another circuit.

Observation:- when switch S is closed, the galvanometer needle deflects and returns to zero. When opening the switch the
needle deflects to the opposite direction and back to zero.
Explanation:- when closing the switch, the current in the primary coil (coil A)sets up a magnetic field which is linked up to
the secondary coil, inducing the current in it. The needle returns to zero as the current reaches a constant value and the
magnetic field is not changing. When opening the switch current is turned off. The magnetic field changes as the magnetic
field lines cutting coil B die, this induces current in B. A soft iron core can be placed between the coils. It will trap the
magnetic field lines so that all of them cut the coil B.
16.3.5 TRANSFORMERS
A transformer is a static device that converts Power from the Primary Coil to the same amount of Power in the
secondary coil.
Contrast that with 1. The Generator that converts Mechanical Energy to Electrical Energy of wire in a Magnetic field,
The wires rotate and cut the magnetic field lines to produce ac current- principle used by power stations.

A transformer is a device which makes use of mutual induction to change voltages (and is frequently used in home to step
down the mains voltage of 230 V to 6 V or 12 V). It consists of two coils of insulated wire wounded on an iron core. The coil
connected to the a.c. input is called the primary coil and the coil that provides the a.c. output is called secondary coil.

If the alternating voltage is applied to the primary coil, the a.c. produces a changing field in the core. This changing magnetic
field induces an alternating current in the secondary coil.
*Note:- 1). The purpose of the iron core is to ensure that all the magnetic field lines generated in the primary
coil is made to pass through all the turns of the secondary coil.

Page 160
 2). A transformer can only operate on a varying voltage. A D.C. voltage in the primary coil will not
produce any change in the magnetic field so with D.C. no current is induced in the secondary coil.
Two types of transformers
1). Step-down transformer
2). Step-up transformer

1). Step-down transformer- has fewer turns on the secondary coil than on the primary coil. Therefore it
produces a smaller voltage in the secondary coil(less output voltage).
2). Step-up transformers- have more turns on the secondary coil than on the primary coil, so their
output/secondary voltage is greater than the input voltage.
The relationship between the number of turns and voltage in the secondary and primary coils can be given by the equation:-
Primary coil voltage/secondary coil voltage = number of primary turns/number of secondary turns
VP/VS = NP/NS

TRANSFORMER EQUATION
If no energy is wasted in a transformer, the power (energy per second) delivered by the output coil will be the same as the
power supplied to the input.
Then, since P =VI, we can have the transformer equation as;
Input voltage x input current = output voltage x output current
V1I1 = V2I2
Note: V α 1/I
This follows that a transformer which increases the voltage will reduce the current in the same propotion, and vice versa.
ENERGY LOSSES IN A TRANSFORMER
All transformers waste some energy because of the following factors
1). Resistance of the copper coils.
Copper coils are not perfect electrical conductors. Whenever some current flow through them, some
electrical power/energy is used to overcome their resistance and this energy will then be given out as
useless heat to the surrounding. Therefore, their resistance need to be kept low, so thick copper wire
should be used where possible.
2). Eddy currents
The core is itself a conductor, so the changing field induces current called eddy current in it. The eddy
currents also cause heating effects. To reduce this, core is laminated i.e. it is made of thin sheets of iron (or
mumetal) instead of a solid block, which are insulated from each other to have a high resistance.
3). Leakage of field lines
All the lines produced by the primary coil may not cut the secondary coil, especially if the core has an air
gap or badly designed.
*Large transformers have to be oil-cooled to prevent overheating.
TRANSMISSION OF ELECTRICAL POWER
1). Power for the a.c. mains is generated in power stations and then transmitted through long –distance
cables. A network of overhead cables, supported on pylons, which connect power station/s to consumers is
called a National Grid. Power from the grid is distributed by a series of substations. These contain step-
down transformers which reduce voltage in stages to level needed by consumers.
2). A.C or D.C?
Electric power is generally transmitted as a.c. This is so because a.c. can be easily and cheaply stepped up
or down using a transformer. A transformer does not work with D.C.
3). High or Low voltage?
Transmission cables have significant resistance, especially when they are hundreds of kilometres long. This
means energy is wasted because of the heating effect of the current.

e.g. What is the power wasted in the cable when 10 kW is transmitted through a cable of resistance 0.5 Ω
at a) 200 V b) 200 000 V
NOTE:- Power loss, P = I2R

Page 161
 a). at 200 V
I = P/V = 10000/200 = 50 A
Then Power loss P = I2R = 502(0.5) = 1250 W
b). at 200 000 V
I = P/V = 10000/200000 = 0.05 A
THEN, P = I2R = 0.052(0.5) = 0.00125 W
From the calculations, it is demonstrated that less power is wasted from a cable if power is transmitted
at high voltage. Then a transformer can be used to increase the voltage, and reduce the current and this
means thinner, lighter and cheap cables can be used.

4). Overhead or underground?

Overhead cables are cheapest way of sending power long distances. Underground cables are more
expensive to lay. However, they are used in areas of outstanding natural beauty, where pylons would spoil
the landscape.

Page 162
17.0 ATOMIC PHYSICS
17.1.1 RADIOACTIVITY
Some materials (isotopes) contain atoms with unstable nuclei and these isotopes are said to be radioactive. The nuclei
can become stable by emitting tiny particles, energy or both. These particles and energy from the nucleus are called
radioactive emissions/radioactivity/nuclear radiation and the breaking-up process is called radioactive decay.
There are three main types of radioactive emissions, namely:-
a) Alpha radiation (α- b) Beta radiation (β- c) Gamma radiation (γ-
radiation) radiation) radiation)
Summary of main properties of the alpha, beta and gamma radiation
Type of radiation Alpha particle (α) Beta particle(β) Gamma rays (γ)
Nature 2 protons + 2 neutrons An electron Electromagnetic waves
(identical to a nucleus of
helium-4)
Charge +2 -1 0
Mass High, compared to β low None
Ionizing effect strong weak Very weak
Penetrating effect Not very penetrating: can be Penetrating: it can penetrate Very penetrating: never
stopped by a thick sheet of through several metres of completely stopped, though lead
paper or by the skin. It can air but stopped by a thin and thick concrete will reduce
penetrate through a few (e.g 2 mm) sheet of intensity
centimetres of air aluminium or other metals
Effects of fields Deflected by magnetic and Deflected by magnetic and Not deflected by magnetic or
electric fields electric fields electric fields

*Ionization occurs when a radioactive emission such as alpha particle knocks electrons off of the surrounding molecules or
atoms leaving them as charged ions. Alpha particle is the most ionizing radiation because it has the greatest size and
mass and charge of +2.
*Penetration power: all the three radioactive emissions can penetrate materials because their sizes are much smaller than
the spaces separating the atoms in materials, even in solids. Beta particles are more penetrating than alpha particles
because they are much smaller. Gamma radiation is the most penetrating because it is an electromagnetic wave without
mass or size.

*Deflection in electric and magnetic field

Alpha and beta particles are deflected by electric fields because they are electrically charged. Alpha particles are least
deflected because of their larger mass and inertia.
• Alpha particles will be attracted towards negatively charged plates because they are positively charged.
• Beta particles are attracted towards positively charged plates because they are negatively charged.

• Gamma radiation has no charge and is unaffected by charged plates.

Any electrically charged particle experiences a force when it moves through a magnetic field (motor effect). Alpha and beta
particles are electrically charged, therefore they will experience a force if they move through a magnetic field and they will be
deflected. Gamma rays have no mass or charge, this means they will pass through a magnetic field without deflection.

Page 163
The direction of deflection can be predicted using Fleming’s left hand rule.

17.1.2 RADIOACTIVE DECAY

Radioactive decay can be defined as a process in which a heavy nuclides (radioisotopes) spontaneously break
down/disintegrates to smaller more stable nuclides. This is a random process; it can never be predicted when an
individual nucleus will suddenly split up. It does not matter whether the substance is in its pure state or combined with
others. Also cooling or heating has no effect on the disintegration of the nucleus. Examples of radioactive elements: carbon-
14, uranium-235, uranium-238, cobalt-60, caesium-137, polonium-213, iodine-131, barium-143
The number of nuclei that disintegrate per second is called the activity of the radioactive material. The unit of the activity is
called the Becquerel, Bq
activity = number of nuclei which decayed/time taken in seconds
1 Bq = 1 disintegration (decay) per second
(a) Alpha (α) decay
During alpha decay, an unstable nucleus emits 2 protons and 2 neutrons as single particle , known as alpha particle, that
travels at high speed. Therefore an alpha particle is a nucleus of a helium atom. When an atom decays by α emission, its
mass number decreases by 4 and its atomic number decreases by 2.
ZAX -------------------------> Z-2A-4Y + 24He
(parent nuclide) (daughter nuclide) α-particle

e.g. 88226Ra -------------------> 86222Rn + 24He

92238U ------------------> 90234Th + 24He
*Note: when an element decays by emission of an alpha particle it turns into an element with chemical
properties similar to those of an element two places earlier in the periodic table.
(b) Beta (β) decay
In a beta decay, a neutron changes to a proton and an electron. The proton remains in the nucleus but the electron escapes
at high speeds in form of a beta particle. The new nucleus has the same mass number but its atomic number increases by
one.
ZAX ------------------------------> Z+1AY + -10e
(parent nuclide) (daughter nuclide) (β-particle)
e.g. 614C ----------------------------> 714N + -10e
1940K ------------------------> 2040Ar + -10e
*Note: When an element disintegrates by emission of β-particle it turns into an element with properties similar to
those of an element one place later in the periodic table.
(c) Gamma radiation
After emitting α-particle or β-particle, some nuclei are left still in an excited state, i.e. has surplus energy and therefore
unstable. So such nucleus emits this energy as γ-radiation/rays. When a nucleus undergoes gamma decay, it keeps the
same atomic number Z and the same mass number A. The gamma radiation only carries away energy so that the nucleus
becomes more stable.
Note: Cobalt-60 and Radium-226 are common gamma emitting nuclides.

Page 164
Detection of radioactive emissions
Most methods of detection depend on the fact that all three radiations can ionize air molecules.
a) Photographic paper or film: Radiation can affect photographic film in much the same way as light or X-rays.
b) The gold-leaf electroscope: a charged electroscope discharges if a radioactive isotope is moved to the cap. The
radioactive emissions ionize the surrounding air molecules. If the electroscope is negatively charged, the positively
charged ions are attracted to the cap and the charge on the electroscope is neutralized. If the electroscope is
positively charged the electrons which were removed from the air molecules are attracted to the electroscope.
c) Geiger-Muller tube

G.M tube contains argon gas that ionizes when radiation passes through, thereby creating ions and electrons. The
positive ions move towards the cathode and negative electrons move to the anode. This produces some electric
current which will be fed to a scaler or ratemeter.
Scaler- counts pulses and shows total received in a certain time.
Ratemeter – gives counts per seconds. Some have a loudspeaker which would give a ‘click’ per each count.
Other detectors are i) spark counter, ii) ionization detector and iii) cloud chamber

17.1.4 Uses of radioactivity

1. Thickness gauges: Radioactive isotopes help manufacturers to check and carefully control the thickness
of product like duplicating machines paper.

• a radioactive isotope is placed on one side of the material and a detector on the other side.
• The amount of particles (radiation) reaching the detector is monitored closely by the machine
operator or control unit. If the thickness of the material (paper) increases, fewer particles will
reach the detector and visa versa
*The isotope has to be chosen to suit the requirements of the manufacturer. For example, an alpha
emitting isotope would be suitable choice for a paper factory and a beta source would be more
suitable for a steel mill. Gamma sources are not suitable since gamma is a very penetrating
radiation.
2. Sterilization of surgical equipment: Surgical equipment is placed in sealed bags and then exposed to
short
bursts of gamma radiation. The gamma rays kill any microbes inside the bag and the contents will
remain
sterile until the bag is opened.
• Penetrating gamma rays from cobalt-60 are used to kill cancer cells in the body.
3. Long-life fruits and vegetables: Many fruits are also exposed to short bursts of gamma radiation. The

Page 165
 gamma rays kill any micro-organisms which may be inside the fruit, reducing the chances of the fruit
rotting
whilst on the shop shelves.
4. Medical tracers- some isotopes are used as tracers to see the performance of specific organs in the
body
such as kidneys or the thyroid gland. The patient will be given a liquid containing iodine-123, a gamma
emitter and a detector would then be used to measure the activity of the tracer to find out how quickly
iodine becomes concentrated in the gland.
5. Radioactive isotopes can be used as tracers to detect leaks in underground pipes for gas, water and
sewage.
A small amount of gamma radiation source is injected into the pipe and the leak can later be detected
with
Geiger-Muller tube.

6. In Agriculture isotopes can be used:- i) as tracers to find how fertilisers and other nutrients are used in
plants. ii) to alter genes in seeds to produce genetically modified plants with superior qualities to
natural
plants.
7. Carbon dating: this technique is used by historians and archaeologists to estimate age of historic
artefacts
and also it is used by geologists to estimate the age of rocks and fossils.
17.1.5 Dangers of Radiation
• The danger from alpha particles is slight.
• Large doses of beta and gamma rays can cause radiation burn
• Gamma rays can penetrate deep into the body and destroy cells inside the body or cause cells to multiply
uncontrollably forming cancer or damage chromosomes causing genetic defects (mutation).

17.1.6 Safety handling and storage of radioactive isotopes

Even when a radioactive material emits low levels of radiation, (e.g. materials used in school laboratories),
it must be handed with extreme care.
Handling:
• Always handle isotopes using forceps or special gloves
• Keep away from eyes. Do not point the source towards any person.
• Always wash hands after handling.
Storage
• Keep the samples in special boxes lined with lead
• Store the boxes in a locked cupboard
Disposal of radioactive waste
• Burn low-level waste or bury it in the ground or release it into the sea
• High-level waste in steel drums are buried in disused mines or granite caves or bedded in concrete and
dumped in deep oceans. Or stored at special factories for re-processing.
17.1.7 Background Radiation
It is low level radiation that is always present around, mainly because of radioactive materials in the
ground and air. Every person on Earth is exposed to this form of radiation. Major sources are:
• Rocks • Cosmic and solar rays • Buildings
• Soils and underground • Food and drinks
water • Man-made radiation
17.1.8 DETECTING ALPHA, BETA PARTICLES AND GAMMA RAYS BY INVRESTIGATING
PENETRATING ABILITY - EXAMPLE
The source is a piece of radium which emits all the three types of radiation.

Page 166
 X Y

• Switch on the meter and record the background radiation.

• Set the source at position X and take a reading all the three radiation.
• Put a sheet of paper at Y (between the source and the G. M tube)and take a reading for beta gamma rays.
• Put a 3 mm sheet of aluminium at Y and take the reading for gamma rays only.
• In each case subtract the background radiation from the meter reading
A typical set of results is shown below on the table

17.1.3 HALF-TIME
Some isotopes decay much more rapidly than others. Scientists measure the decay rate of an isotope in the form of half-
lives.
Half-life is defined as the time taken for half the original number of radioactive nuclides to decay or the time taken for
the activity of a radioactive isotope to fall to half its original value. This time is the same no matter what the original
activity is.
Example: Thoron gas is radioactive and has a half-life of 52 s. the table shows how the amount of thoron is halved every 52
s.
Time/s 0 52 104 156 208
Mass of 120 60 30 15 7.5
thoron/g
Fraction 1/2 1/4 1/8 1/16
remaining

*very unstable nuclides decays quickly than one with greater stability but in every case the rate of radioactive
decay is proportional to number of nuclei present.
Rate of decay α N
Rate of decay = λN where N = number of nuclei present
λ = is a constant
EXAMPLES
Isotope Type of emission Half-life
Uranium-235 α 700 million years
Carbon-14 β 5 700 years
Cobalt-60 β, γ 5 years
Sodium-24 β 15 hours
Strontium-93 β, γ 8 minutes
Barium-143 β 12 seconds
Polonium-123 α 4 x 10-6 seconds

A graph for radioactive decay (Decay curve)

The graph is known as exponential curve. Even though the curve falls, it never quite reaches x-axis. The graph shows that
activity reduces by the same fraction in successive equal time. E.g.

Page 167
If the curve falls from 80 counts/s to 40 counts/s in 10 min, then from 40 counts/s to 20 counts/s in the next 10 min, from 20
to 10 counts/s in the 3rd 10 min and so on, half-life is then 10 min.
*If count rate is N at time t1 and has fallen to N/2 at time t2 then half-life t1/2 is t2 – t1. Similarly, if the count
rate has fallen to N/4 at time t3, the half-life is t3 – t2.
If at the beginning there are N undecayed nuclei, after 1 half-life there will be N/2, after a second half-life there will be ½ x
N/2 = N/4, after third half-life there will be ½ x N/4 = N/8 undecayed nuclei, etc.

Material at Y Meter reading Background Radiation detected Reading - background

None 186 6 α, β, γ 180
Paper 126 6 Β, γ 120
Aluminium (3 mm) 87 6 γ 81

Using these results:

The alpha radiation is 180 – 120 = 60
The beta radiation is 120 – 81 = 39
The gamma radiation is = 81
17.2.0 NUCLEAR REACTION
17.2.1 Nuclear fission
Nuclear fission is the splitting of a heavy nucleus (such as U-235) by hitting it with a neutron into two nearly equal smaller
nuclei and two or three neutrons. The lost mass appears as energy.

Page 168
A beam of neutrons is directed at the uranium atom. If a neutron strikes a nucleus of U-235, this splits into two roughly equal
parts, and shoots out two or three neutrons as well. If these neutrons hit other U-235 nuclei, they make them split and give
out more neutrons. And so on. This process is known as a chain reaction.
92235U + 01n -------> 56144Ba + 3690Kr + 2 01n
If the chain reaction is uncontrolled, huge numbers of nuclei are split in a very short time. The heat builds up so rapidly that
the material bursts apart into an explosion. This happens in a nuclear (atomic) bomb. If the chain reaction is controlled, there
is a steady output of heat. This happens in a nuclear reactor.
A NUCLEAR REACTOR

In nuclear reactors, fission is carried out in a controlled way. Reactors use naturally occurring uranium, U-235 and U-238
but only U-235 undergoes fission with slow neutrons. Neutrons from the fuel rods go into graphite core, where they collide
with graphite atoms and lose K.E. The graphite is called a moderator because it slows down the neutrons. The neutrons
then pass into fuel rod (which consists of uranium) and cause fission. The boron steel rods control the rate of fission by
absorbing some neutrons. The heat generated by nuclear fission warms a coolant fluid which circulates through the
moderator. The coolant may be water or gas CO2 . The heat is used to turn water into steam. The steam drives the turbines
and generates electricity.
17.2.2 Nuclear fusion
In fission a heavy nucleus split in two to release energy. On the other hand in nuclear fusion the opposite is done to produce
large amounts of energy.
Nuclear fusion is the combination of two light nuclei to form a heavier nucleus, e.g. two nuclei of hydrogen-2 (deuterium) can
be combined to form a nucleus of helium-3.
12H + 12H --------------> 23He + 01n
For two nuclei to fuse, they must be brought sufficiently close to each other. But it is difficult to do this as they repel each
other with large electrical force. To overcome this repulsion, the nuclei have to be heated to high temperature (e.g. 10 8 K) so
that they gain enough K.E.
• The sun obtains its energy from nuclear fusion. In the sun the temperature is about 10 million °C and the
hydrogen-2 atoms have enough energy to fuse.
• Uncontrolled fusion on Earth can result with hydrogen bomb. Initial high temperature required is obtained by using
an atomic (nuclear) bomb to trigger off fusion. A hydrogen bomb releases much more energy than an atomic
bomb.

17.2.3 Nuclear energy

In radioactive changes (or nuclear reaction), a little bit of mass disappears (this is called mass defect), and equivalent
amount of energy appears as kinetic energy of the formed particles.
The relationship between these mass and energy can be given by the following equation (formulated by Albert Einstein)

E = mc2
where c2 = speed of light, 3 x 10 m/s

E.G:- When radium decays into radon, about 1/40 000 0f the mass of each decaying atom disappears. Calculate
the energy released from 1 g (1/1000 kg) when it decays to radon.
Data: m = mass disappearing = (1/400 000) x (1/1000 kg) = 1/(4 x 10 7) = 2.5 x 10-8 kg
c = 3 x 108 m/s
E = mc2
= 2.5 x 10-8 x (3 x 108)2

Page 169
= 2.25 x 109 J

Page 170
Page 171