0% found this document useful (0 votes)
25 views2 pages

Internet of Things Trainer

The document describes the XPO-IOT Internet of Things Trainer developed by Anshuman Tech Pvt. Ltd., featuring a mother board with various interfaces and sensors for educational purposes. It supports multiple programming environments and hardware platforms, including Raspberry Pi, Arduino UNO, and ESP 32, along with a range of application boards for hands-on experiments. The trainer is designed to facilitate learning in IoT through practical applications and comprehensive instructional materials.

Uploaded by

kulharivikash
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
25 views2 pages

Internet of Things Trainer

The document describes the XPO-IOT Internet of Things Trainer developed by Anshuman Tech Pvt. Ltd., featuring a mother board with various interfaces and sensors for educational purposes. It supports multiple programming environments and hardware platforms, including Raspberry Pi, Arduino UNO, and ESP 32, along with a range of application boards for hands-on experiments. The trainer is designed to facilitate learning in IoT through practical applications and comprehensive instructional materials.

Uploaded by

kulharivikash
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INTERNET OF THINGS TRAINER (Model : XPO-IOT) (Family of Training Systems)

ANSHUMAN
TECH PVT. LTD
Tel: +91-20-25460892, 25463052
Email: [email protected]
[email protected]
Manufacturers of
Quality Test & Measurement, Technical Education Equipments

Mother Board (MB)

SALIENT FEATURES u I2C, SPI etc. interfaces available to access sensors and application boards.
u Based on IOT Kit designed by IGTUW Professor, Delhi. u Aesthetically engineered / Plastic molded enclosure designed to protect &
u IOT kit is based on open source hardware, software (Raspberry Pi) & preserve small footprint SBC .
development tools to provide solutions for integrating application u Optionally many communication modules like bluetooth, zigbee etc. and
development with open-source OS Variant (Debian) or Arduino UNO or many agro, weather sensors & actuators like stepper motor, DC motor,

www.anshumantech.net/.in
ESP 32 with IDE supporting bare metal programming in C to prototype the Relay or 37 in 1 project components etc. are supported using IOT
project ideas and experiments. application boards.
u Choice of programming ports Ethernet/ WiFi / USB available for internet / u Provided with excellent Student Workbook and Instructor’s guide.
PC access.

Technical Specifications of Mother Board (MB):-


Particulars Device Names
I2C sensors Light & Infrared (TSL2561-6 P/TMB), Altimeter (MPL3115-8P/LGA), Magnetometer (MAG3110-10P/DFN), 3-Axis
(Qty=8) Accelerometer (MMA8491-12P/QFN ), Gyroscope (FXAS21002C-24P/QFN), RTC (DS1337-8P/SOIC), Non-contact IR
Temperature (MLX90614-4P/TO 39),Gesture (APDS9960-8P/DFN), or optionally VL53L0X-12P/LGA

VLSI Embedded Trainer


GPIO Sensors Temp and Humidity (DHT11-3P/SIL), Temp. sensor (DS18B20-3P/TO 92), PIR (HC-SR501-3P/SIL), Ultrasound (HC-SR04-4P/SIL),
(Qty=5) LDR (100K -2P), Photo reflective sensor (Transmitter - TIL 38/2P, Receiver -TIL 81/2P)

Peripherals PS2 Keyboard, USB to serial ( COM port) converter using CP2102, Buzzer, USB Webcam, 8 bit R-2R DAC O/P,
(Qty=6) Push button switches- 4nos.,Bi-colour Leds - 4nos.

Connectors 1] 14 Pin FRC Box Header for CB 2] 26 Pin FRC Box Header for External boards, 3] 14 Pin DIL Header for TCP

Power Supply Options Select one of 2 options I) 5V /2.5 Amp SMPS with RCA plug. II) 5V /2.5 Amp SMPS with RCA
(SMPS), 2 options plug +12 V/ 850 mA, -12V/250 mA with 4 pin reliamate SMPS (3.3V generated on MB)

Mechanical Aesthetically designed Injection molded plastic extended enclosure of size 215(L)x165(W)x100(H)mm.
Details Weight = 900 gm.(1.5 Kg with manuals)

IOT Application 1] ST/DC motor application board containing 12V stepper motor,12V PMDC motor, 12V relay, level translator I/F circuit etc.
Boards 2] Combo application board (CAB) containing a) 3 SILs for inserting 1 of many application modules from XPO-EST including BT, GSM
(Optional) communication modules etc. b) DAQ function block for digital filter application consists of R-2R 8 bit DAC, 8 bit I2C AD-DA,
signal conditioning circuit like summer; noise adder, level shifter to I/F with external audio box [XPO-COM]. c) Provision of
reliamate connectors to interface external agriculture sensors, weather sensors etc.
3] 37 in 1 project components / devices supported.

240111
Technical Specification : Note: Select any one controller per kit.
Sr.
No. Model Raspberry PI (With OS) Arduino UNO (Without OS) ESP 32 C3 (Without OS)
1 Processor IC BCM2837, 64 bit ARM Cortex Atmega328P, 8 bit AVR Microcontroller PCB module 32-bit RISC-V single-core
A53 Quad Core 1.2 Ghz processor

2 OS Debian loaded in 8GB SD Card Without OS, Bootloading Required


Optionally Android / Noobs

3 Programing Python / Scratch / C C/ C++ C/ C++


4 IDE OS based IDE Thonny Arduino IDE Arduino IDE

5 RAM 1 GB DDR2 2 KB SRAM 400 KB SRAM/ 16 KB for cache


6 Flash 8 GB SD CARD for OS 32KB (Int. Flash) 4 MB (SPI Flash)

7 USB 3 Host 1 OTG Type A connector 1 type B connector 1 Micro connector


8 HDMI port 1 NA NA

9 uSD/SD card socket uSD port NA NA


10 GPIO 31 20 GPIO (6 Analog I/O, 14 Digital I/O) 15 GPIO
11 Connector 40 pin DIL header 17 + 13 SIL berg housing 17 + 13 SIL berg stick
12 LCD display 5" Color TFT mounted inside the 2" Color TFT using SPI mounted
cover or Ext HDMI monitor on TCP inside the cover

13 Ethernet 10/100 BaseT Ethernet Socke NA NA


14 Wi-Fi IEEE 802.11 b Built in NA IEEE 802.11 b Built in
15 Bluetooth V4.1 built in NA LE BT
16 UART, I2C, SPI 1 each 1 each Overlapped with GPIO 1 each Overlapped with GPIO
17 Audio / Video EP Socket / 15 Pin FFC CSI NA NA

List of experiments:- Note: 1] Following experiments are applicable for Raspi while for Arduino Uno / ESP 32 only B/II, III & C, D
experiment may be performed. 2] For C, D experiments need to purchase optional application boards.
A) Learning Experiments:- • Temperature measurement using DHT11, DS1820
www.anshumantech.net/.in

• Downloading the operating system and mounting it on MicroSD card • Sense Proximity using Passive Infrared (PIR) sensor
• Loading the Image File on SD card • Sense any obstacle using photo reflective sensor
• Changing Keyboard settings • Sense the presence of ambient light using LDR
• TFT settings • Measure distance of an object using Ultrasound sensor
• Enabling I2C interface III) Sensors: I2C Based (select 1 or more)
• Installing GPIO library files • Measure altitude using Altimeter
• App Development using MIT App Inventor(For Android OS) • Measure physical orientation of the MB w. r. t. ground using Gyroscope in
• How to save data on Cloud using Thingspeak cloud server raw data format.
• How to write simple programs using SCRATCH • Measure physical orientation of the MB w. r. t. ground using Gyroscope in
radians/sec format.
B) Programming Experiments: • Measure X, Y, Z acceleration and orientation of MB w. r. t. a predefined
I) Operating System (OS) based:- zero position using Accelerometer.
• RTC Setting Up and Test • Find geographical direction using Magnetometer
• Networking • Initialize a Real time clock (RTC) and read time data using RTC chip
VLSI Embedded Trainer

• Store temperature sensor value in file under OS, Store ADC values • Measure Light and Infrared intensity using Light and Infrared chip
in a file under OS • Measure Temperature using Non-Contact IR sensor (MLX90614) ('c' code)
• Check Wi-Fi in your laboratory • Identify gestures using IR Gesture IC (APDS9960).
• Accessing the Web sites using HTTP protocol • Measure voltages for respective ADC and DAC values using PCF8591.
• File Downloading using FTP Protocol C) Combo application board based experiments : (Select 1 or more)
• Using Scratch to write simple programs :- (i) GSM module : Initiate a call, receive a call and send and receive an SMS
a) Hello world b) Road crossing game (ii) GPS module : Get Geographical location of the kit using GPS
(iii) Zigbee Module: Send and receive data using Zigbee
• Write and run the Shell Script
(iv) Bluetooth Module: Send and receive data using Bluetooth
• Create your GUI using python
(v) IR transceiver module : Send and receive data using IR Transceiver
• Playing Audio file using python programming,
(vi) Wi-Fi module: Connect to a network and transfer data using Wi-Fi
• Playing Audio file using alsa mixer.
(vii) Fingerprint module : Enrollment & recognition
• Interfacing TFT Touch panel using SPI (viii) Misc. experiments with agro / weather sensors.
• Setting Raspberry pi as webserver
• Face recognition using USB camera D) STDC motor application board based experiments :
II) Sensors: GPIO based (I) Speed / Direction / PWM controls of DC motor
• Program for LED blinking using on-board LED (ii) Direction / Stepping control of stepper motor
• Program for buzzer using on-board buzzer (iii) Relay control

You might also like