Figure / Diagrams to practice
Unit 1: Energy FLAT PLATE COLLECTOR (Solar Water Heater)
resources and Prime
movers
Concentrating type
4 stroke SI engines : Suction stroke, Each stroke –
Compression Stroke, engine diagram
Expansion/working/power Stroke, Exhaust and P- V plot
Stroke
4 stroke CI engines : Suction stroke, Each stroke –
Compression Stroke, engine diagram
Expansion/working/power Stroke, Exhaust and P- V plot
Stroke
Battery Electric Vehicle Architecture
Series HEV Architecture
Parallel HEV Architecture
Plug-in HEV Architecture
Steam turbine IMPULSE TURBINE (De Laval turbine) P – V plot, steam
flow figure
REACTION TURBINE- Parson’s turbine
Water turbine Impulse Turbine or PELTON WHEEL
FRANCIS TURBINE
Gas turbine Open loop gas turbine
Closed loop gas turbine
Wind turbine Horizontal axis and Vertical axis wind turbine
Unit 2: Engineering Composites : particulate, flake, and fibers
Materials
Tensile test specimen
Stress strain curve typical
Stress strain diagram for ductile material
Aluminum or Copper
Brittle material Stress strain curve
Elasticity , Plasticity , Toughness, Resilience
property
Unit 3: Motion and Kinematic link : Reciprocating steam engine
Power Transmission
Sliding pair, Turning pair, Rolling pair, Screw
pair, Spherical pair, Lower pair, Higher pair,
Completely constrained motion, Incompletely
constrained motion, Successfully constrained
motion
Kinematic Chain : Four bar chain
Beam engine (crank and lever mechanism}
Inversion of a Four-bar Coupling rod of a locomotive (Double crank
chain mechanism)
Inversions of Single Pendulum pump or Bull engine.
Slider Crank Chain Oscillating cylinder engine.
Rotary internal combustion engine or Gnome
engine
Different types of belts
Open Belt drive
Cross Belt drive
Stepped (Cone) pulley drives
Jockey Pulley
Different types of chains
Gear drives Spur gear, Helical Gears, Double
Helical/Herringbone gear, Bevel gear, Hypoid
gear, Worm gear, Rack and Pinion
Gear Terminology
Simple gear train
Compound gear train
Reverted Gear Train
Epicyclic Gear Train
Planetary gear train
Unit 4: Manufacturing Sand casting, flow chart
processes and Fasteners
Pattern allowances
Types of Pattern : Solid pattern, Split attern ,
Match plate pattern, Cope and drag pattern ,
Loose-piece pattern, Sweep pattern,
Casting Defects : Shift or Mismatch
, Swell, Blowholes
, Drop
, Metal Penetration, Pinholes, Shrinkage
Cavity, Hot Tears or Hot Cracks, Cold Shut
, Misrun
,
Metal Forming
: Rolling,Forging, Extrusion, Drawing, Deep
drawing
Arc welding (Metal arc)
Gas Welding ,
Gas flames
Resistance Welding Spot welding, Seam welding
Soldering Procedure
Brazing
External thread, Internal thread
Thread terminology
Bolt terminology
Stud terminology
Riveting, Lap Joint, Butt joint
Unit 5: Machining and
Robotics
Lathe working principle
Specifications of Lathe
Lathe Operations: Turning, Facing, Thread
cutting, Taper turning,
3 jaw chuck, 4 jaw chuck
Drilling: types- reaming, counter boring, boring,
counter sinking, tapping, spot facing
Milling Up milling, Down milling
Horizontal milling
Vertical milling
Slab milling, slotting, Side milling, Straddle
milling, Form milling, Angular milling, Profile
milling, Pocket milling, Surface contouring.
Horizontal Machining Centre HMC
Robotics Robot
Robot joints
Robot configurations
Automation Control System: Open loop
And Feedback control system