CRYSTAL CLOCK OSCILLATORS Data Sheet 9205A

Rev. M
ECL
HS-800/810 Series

Description
The HS-800/810 Series of quartz crystal oscillators provide MECL 10K and 10KH series compatible signals
in industry standard four-pin DIP hermetic packages.. Systems designers may now specify space-saving,
cost-effective packaged ECL oscillators to meet their timing requirements.

Features
• Wide frequency range–15.0MHz to 250.0MHz • MECL 10K and 10KH series compatible output
• User specified tolerance available on Pin 8
• Will withstand vapor phase temperatures of 253°C • High Q Crystal actively tuned oscillator circuit
for 4 minutes maximum • Power supply decoupling internal
• Space-saving alternative to discrete component • No internal PLL avoids cascading PLL problems
oscillators • High frequencies due to proprietary design
• High shock resistance, to 3000g • Gold plated leads - Solder dipped leads available
• All metal, resistance weld, hermetically sealed upon request
package • RoHS Compliant, Lead Free Construction
• Low Jitter (unless solder dipped leads are supplied)

Electrical Connection
HS-800
Pin Connection

1 N.C.
7 VCC /Ground
8 Output
14 VEE -5.2V

HS-810
Pin Connection

1 N.C.
7 VEE -5.2V
8 Output
14 VCC /Ground

Dimensions are in inches and (MM)

357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com
 CRYSTAL CLOCK OSCILLATORS Data Sheet 9205A

Rev. M
HS-800/810 Series Continued
ECL
Operating Conditions and Output Characteristics
Electrical Characteristics
Parameter Symbol Conditions Min Typical Max
Frequency ----- ----- 15.0MHz ----- 250.0MHz
Duty Cycle ----- @ VCC-1.29V 45/55% ----- 55/45%
Logic 0 (2) VOL ----- VCC-1.95V ----- VCC-1.60V
Logic 1(2) VOH ----- VCC-1.02V ----- VCC-0.74V
Rise & Fall Time tr,tf 20-80%VO with 50 ohm load to VCC-2V ----- 1.0 ns 1.5 ns
Jitter, RMS(3) ----- ----- ----- ----- 5 psec
Frequency Stability (1) dF/F Overall conditions including: -100ppm ----- +100ppm
voltage, calibration, temp.,
10 yr aging, shock, vibration

General Characteristics
Parameter Symbol Conditions Min Typical Max
Supply Voltage VEE ----- -5.46V -5.2V -4.94V
Supply Current IEE 50 ohm termination 0.0 mA ----- 80 mA
To 2.00V below VCC
Output current IO Low level Output Current 0.0 mA ----- ±50.0 mA
Operating temperature TA ------ 0°C ----- 70°C
Storage temperature TS ----- -55°C ----- 125°C
Power Dissipation PD ----- ----- ----- 437 mW
Lead temperature TL Soldering, 10 sec. ----- ----- 300°C
Load 50 Ohm to VCC-2V or Thevenin Equivalent, Bias Required
Start-up time tS ----- ----- 2 ms 10 ms

Environmental and Mechanical Characteristics

Mechanical Shock Per MIL-STD-202, Method 213, Condition E
Thermal Shock Per MIL-STD-833, Method 1011, Condition A
Vibration 0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz
Soldering Condition 300°C for 10 seconds
Hermetic Seal Leak rate less than 1 x 10-8 atm.cc/sec of helium
ESD Sensitivity Human Body Model per ON Semiconductor 10kH series ECL: 500V min.

Footnotes:
1) Standard frequency stability (±20,±25,±50ppm & others available)
2) VOL, VOH, referenced to ground (VCC) with VEE = -5.2V
3) Jitter performance is frequency dependent. Please contact factory for full characterization.
RMS jitter bandwidth of 12kHz to 20MHz.

Creating a Part Number

HS - A80X - FREQ

Package Code Tolerance/Performance

HS Leaded 4 pin (14 pin) 0 ±100ppm 0-70°C
SM Leaded 4 pin (14 pin) SMD 1 ±50ppm 0-70°C
Gull Wing 7 ±25ppm 0-70°C
Input Voltage 9 Customer Specific
Code Specification A ±20ppm 0-70°C
A 3.3V B ±50ppm -40 to +85°C
5V C ±100ppm -40 to +85°C

357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone 262/763-3591 FAX 262/763-2881
Email: [email protected] www.nelfc.com