Scribd
Upload
11 views3 pages

FAT LV Drive Procedure

The document is a Factory Acceptance Test Report for a project involving Schneider Electric, detailing the criteria and items tested during the acceptance process. It includes checks on conformity, mechanical operations, electrical continuity, insulation resistance, and electrical function tests. The report requires signatures from customer representatives and quality control inspectors to confirm the results.

Uploaded by

Om Indra Nugraha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
11 views3 pages

FAT LV Drive Procedure

The document is a Factory Acceptance Test Report for a project involving Schneider Electric, detailing the criteria and items tested during the acceptance process. It includes checks on conformity, mechanical operations, electrical continuity, insulation resistance, and electrical function tests. The report requires signatures from customer representatives and quality control inspectors to confirm the results.

Uploaded by

Om Indra Nugraha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

SEEE Factory Acceptance Test Report

工厂验收报告

Project / 项目名称： Order No. / 订单号：

Customer / 客户名称： Cubicle No. / 柜号：

Factory Acceptance Test Criteria / 工厂验收标准：

1. Contract documents / 合同文件

2. Meeting minutes and correspondence between Customer and Schneider


客户与施耐德之间的会议纪要，信函

3. Engineering documents / 工程图纸

4. Standards / 适用标准
GB 7251.1，IEC 61439-1

Factory Acceptance Test Items / 工厂验收检查项目： (Refer to next page/ 见下页)

Customer Representative Quality Control Inspector Project Execution


客户代表 质检 项目执行
Signature/签字 Signature/签字 Signature/签字

Date / 日期 Date / 日期 Date / 日期

Internal Use Only


Copyright Schneider Electric Equipment Engineering (Xi'an) Co. Ltd. # Public FORM-QM-598 Rev.C
Factory Acceptance Test Items / 工厂验收检查项目
Equipment No.柜体编号 检测结果/Result

1 Conformity checking /符合性检查

Appearance / 外观: 喷漆颜色及质量 / color, paint


Checking of nameplate and labeling / 铭牌和标签检查
Checking of protection degree / 防护等级检查
Busbar: arrangement, size / 母排：母排的布置与尺寸
Cable entry and outgoing facilities / 电缆进出设施
Checking of product consistency / 产品一致性检查（关键件、结构、材料一致性检查）

2 Mechanical operation tests/ 机械操作检查

Mechanical function test of each function unit / 功能单元机械性能检查:


Switch on/off / 开关分合闸操作
Interlocking / 机械操作机构互锁测试
Padlocking / 挂锁

3 Exposed conductive parts electrical continuity / 裸导电部件电气连续性

GB 7251.1，IEC 61439-1 test current 测试电流10A

Front Door前门 mΩ Back Panel背板 mΩ


Left Panel左侧板 mΩ Right Panel右侧板 mΩ

4 Insulation resistance measurement/绝缘电阻测量& Measuring dielectric withstand / 耐压测试


Set 500Vdc DC position and measure insulation resistance
设置500Vdc直流电压档,量测绝缘电阻>1Mohm. equipment No.： E151218030049
VSD output to earth (Before withstand)
变频器输入输出对地（耐压前） MΩ

High pot test/ 耐压测试： V/s

Leakage Current/漏电电流 mA

VSD output to earth (After withstand)


变频器输入输出对地（耐压后） MΩ

5 Electrical function test of each function unit/功能单元电气性能检查：

Input voltage of transformer/变压器输入电压 V

Output voltage of transformer/变压器输出电压 V

Load test/负载测试
Main output voltage,Phase of output/三相输出电压 V
Fan test/ 风扇测试

Internal Use Only


Copyright Schneider Electric Equipment Engineering (Xi'an) Co. Ltd. # Public FORM-QM-598 Rev.C
Factory Acceptance Test Items / 工厂验收检查项目
Equipment No.柜体编号 检测结果/Result

5 Electrical function test of each function unit/功能单元电气性能检查：


Temperature protection/温度保护
Safety function /安全功能
Control panel test: manual and automatic control/控制面板测试：手动及自动控制
Control panel test: signal/控制面板测试：信号
Control panel test: indicating inspection/控制面板测试：指示检查

6 Comments / 备注：

测试人员 Tester 客户代表Customer representer

Internal Use Only


Copyright Schneider Electric Equipment Engineering (Xi'an) Co. Ltd. # Public FORM-QM-598 Rev.C

You might also like