Technical Specification for Digital VHF FM Hand Held Walkie-Talkie without Keypad

General Specification

Operating Mode Supports both FM & Digital Mode

Number of channels 16 or higher

Frequency 136MHz-174 MHz

Channel spacing 12.5KHZ,25 KHZ

RF output Power 5 Watt or more

Battery life(in digital Mode) with

13.5 hours or more
duty cycle 5-5-90

Power Supply (nominal) Nominal 7.5V or 7.2V

Transmitter

Frequency stability ±2.0 PPM or better

Protocol/standard ETSI TS 102 361-1, -2, -3 or Equivalent

For disallowing inadvertent keying of the

Time out Timer transmitter, to prevent locking up one of the
communication channel.

Receiver

Analog Sensitivity(12dB SINAD) 0.25µV or better

Digital Sensitivity (5% BER) 0.30µV or better

Inter-modulation 70 dB or better

Spurious Rejection 70 dB or better

Audio
Rated Audio 0.5 W or More

Audio Distortion at Rated Audio 3% or Better

Hum and Noise -40 dB (12.5 kHz channel) or Better

Environmental & Standards

Operating Temperature -30 °C to +60 °C

Dust and Water Intrusion IP-67 or Advance

Packaging Test MIL-STD 810D and E or Advance

1
Essential Features

a) Single key Selective call facility

Features b) Channel Announcement/Indication facility

c) Low battery alert through Indication/Beep/

announcement
General features

a) Rapid Battery Charger With Adapter

b) Belt clip
Accessories to be supplied with c) Battery
each radio set
d) Antenna

e) Any other standard accessories which is supplied

by the OEM with the product.

Manuals/ Literature User manual with each radio

Programming programming kit with software

Warranty Minimum 5 years Warranty.

PC programming as per the user's communication

Programming
need.

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

2
Technical Specification for Full Keypad Digital VHF FM Hand Held Walkie-Talkie

General Specification

Operating Mode Supports both FM & Digital Mode

Full-Keypad Yes

Number of channels 16 or higher

Frequency 136MHz-174 MHz

Channel spacing 12.5KHZ ,25 KHZ

RF output Power (High/Low) 5 Watt or more

Battery life(in digital Mode) with

13.5 hours or more
duty cycle 5-5-90

Power Supply (nominal) Nominal 7.5V or 7.2V

Transmitter

Frequency stability ±2.0 PPM or better

Protocol/standard ETSI TS 102 361-1, -2, -3 or Equivalent

For disallowing inadvertent keying of the

Time out Timer transmitter, to prevent locking up one of the
communication channel.

Receiver

Analog Sensitivity(12dB SINAD) 0.25µV or better

Digital Sensitivity (5% BER) 0.30µV or better
Inter-modulation 70 dB or better
Spurious Rejection 70 dB or better
Audio
Rated Audio 0.5 W or More
Audio Distortion at Rated Audio 3% or Better
Hum and Noise -40 dB (12.5 kHz channel) or Better
Environmental & Standards

Operating Temperature -30 °C to +60 °C

Dust and Water Intrusion IP-67 or Advance

Packaging Test MIL-STD 810D and E or Advance

3
Essential Features

a) Single key Selective call facility

Features b) Channel Announcement/Indication facility

c) Low battery alert through Indication/Beep/

announcement
General features

a) Rapid Battery Charger

b) Belt clip
Accessories to be supplied with c) Battery
each radio set
d) Antenna
e) Any other standard accessories which is supplied
by the OEM with the product.
Manuals/ Literature User manual with each radio
Programming programming kit with software
Warranty Minimum 5 years Warranty.
PC programming as per the user's communication
Programming
need.

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

4
 Technical Specification for Digital VHF MobileBase station

General Specification

Description Required Specifications

Operating Mode Supports both FM & Digital Mode

Number of channels 160 or Higher

Frequency 136MHz-174 MHz

Channel spacing 12.5KHZ, 25.0 KHZ

RF output Power 25 Watt or more

Frequency stability ±1.0 PPM or better

Protocol/standard Digital Mobile Radio standards complied

Weight(With Control Head) Maximum 1.3 Kg

Display Alfa Numeric Display

Power Supply (Nominal) 12.5 or13.6 VDC

Transmitter

FM Hum and Noise -40 dB @12.5 KHZ or better

Audio Distortion < 3%
For disallowing inadvertent keying of the transmitter,
Time out Timer to prevent locking up one of the communication
channel.
Receiver
Analogue Sensitivity (12 dB
0.3µV or better
SINAD)
Digital Sensitivity (5% BER) 0.3µV or better

Inter-modulation 70 dB or better

Spurious Rejection 75 dB or better

Audio Distortion 3% or better

Audio output 4watt or more

Environmental & Standards

Operating Temperature -30°C to +60°C

Dust and Water Intrusion IP54 or better

5
Packaging Test Per MIL-STD 810 D&E or advance

Essential features

a) Single key Selective call facility

Features b) Front panel LCD display panel

c) Channel Announcement /Indication facility

General features

a) Spring - Whip Antenna with 3 meter of LMR240

with suitable connectors at both ends for mobile
Radio sets.
Accessories to be supplied with
b) Mounting fixtures for mobile Radios and inter
each Radio set. connections for battery and mounting fixtures.
c) Any other accessories needed for installation in
vehicle.
d) Any other standard accessories which is supplied
by the OEM with the product.
Manuals/ Literature User manual with each radio

Programming kit programming kit with software

Warranty Minimum 5years Warranty.

PC programming as per the user's communication

Programming
need.

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

6
 Technical Specification for Digital VHF Base station

General Specification

Description Required Specifications

Operating Mode Supports both FM & Digital Mode

Number of channels 160 or More

Frequency 136MHz-174 MHz

Channel spacing 12.5KHZ, 25.0 KHZ

RF output Power 25Watt or more

Frequency stability ±1.0 PPM or better

Protocol/standard Digital Mobile Radio standards complied

Weight(With Control Head) Maximum 1.3 Kg

Display Alfa Numeric Display

Power Supply (Nominal) 12.5VDC or13.6 VDC

Transmitter

FM Hum and Noise -40 dB @12.5 KHZ or better

Audio Distortion < 3%
For disallowing inadvertent keying of the transmitter,
Time out Timer to prevent locking up one of the communication
channel.
Receiver
Analogue Sensitivity (12 dB
0.3µV or better
SINAD)
Digital Sensitivity (5% BER) 0.3µV or better

Inter-modulation 70 dB or better

Spurious Rejection 75 dB or better

Audio Distortion 3% or better

Audio output 4watt or more

Environmental & Standards

Operating Temperature -30°C to +60°C

7
Dust and Water Intrusion IP54 or better

Packaging Test Per MIL-STD 810 D&E or advance

Essential features

a) Single key Selective call facility

Features b) Front panel LCD display panel

c) Channel Announcement/Indication facility

General features

a) Minimum 6 dB Omni directional GP antenna for

static Radio set.
Accessories to be supplied with b) 30 meters of LMR 400 with suitable connectors at
each Radio set. both ends for static Radio set.

c) Power supply Cum Battery Charger.

d) Any other accessories needed for installation.

e) Any other standard accessories which is supplied

by the OEM with the product.
Manuals/ Literature User manual with each radio

Programming kit programming kit with software

Warranty Minimum 5 years Warranty.

PC programming as per the user's communication

Programming
need.

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

8
 Technical Specification for Digital VHF Repeater

 The Repeater should be capable of unattended mode of operation with remote

diagnostics and maintenance features.

 The repeater should work on TDMA with two simultaneous communication slots
for Voice / Data on each of frequencies.

GENERAL

Operating Mode Supports both FM & Digital Mode

Number of Channels 16 or more.
Repeater should be capable of access code validation
of subscribers, and, should have facility to deny access
Repeater Access control
of black list subscriber Id's range to prevent un-
authorized access.
136MHz - 174 MHz with 12.5KHz for two voice slots in
Frequency Band
Digital Mode

Maximum Duty Cycle 100% duty cycle

TRANSMITTER
25 watts at 100% duty cycle
RF Power Output
50 watt at 50% duty cycle
Frequency stability +/- 1.0 ppm or better
FM Hum/noise 12.5 KHz : 50 dB or better
Audio Distortion 1% typical at 1KHZ
RECEIVER
1) Analog : 0.30 μV or better for 12 dB SINAD
Sensitivity
2) Digital : 0.28μV or better for 3% to 5% BER
Selectivity (Adjacent Channel) 63 dB @ 12.5 Khz or better
Inter modulation 73 dB or better
Audio Distortion Less than 1% typical at 1KHZ
Essential Features
1) Ethernet ports of RJ 45 & USB interface

2) Should have capability to provide Wide Area IP

Interfaces connectivity for voice and data.
3) Provision for Remote monitoring & Alarm controls
4) Inbuilt Fault Alarm interface
Programming kit with maintenance and monitoring
Software
software

9
 1) Antenna: Minimum 6 dB GP antennas
2) Cables: 80 meter of RG 217 connectorised.
3) Power Supply Cum Battery Charger
Accessories 4) Galvanized Anti-Rust Rack (standard 19 inch) to
install two Repeaters.
5) Any other accessories needed for installation.
6) Any other standard accessories which is supplied
by the OEM with the product.
Environmental Operating Temperature: -30 °C to + 60°C
General Features
Mounting Rack (standard 19 inch)
Weight Maximum 10 Kg
Literature User manual with each repeater set
Warranty Minimum 5 years warranty.

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

10
 Technical Specification for Multi-Unit Charger

Number of charging Pockets 6

Power Source 120-240 VAC
Must be compatible with the Both type of
Compatibility Hand Held Walkie Talkie Set and should be
of same OEM as Walkie Talkie.

Technical Specification for Hands Free Kit/Earpiece

Microphone YES
PTT YES
Speaker Single Ear
Configuration Over The Ear
Must be compatible with the Both type of
Compatibility Hand Held Walkie Talkie Set and should be
of same OEM as Walkie Talkie

Technical Specification for Level Printer

A portable Industrial Handheld Label printer (Preferred make: DYMO/Brother)

Easily enter text with a familiar computer-style (QWERTY) keyboard or Meet key ANSI and
TIA/EIA-606-A industry labeling standards.
Print 6, 9, 12, 18/19mm or higher width industrial-strength labels in a variety of materials and
colors – plus print directly onto heat-shrink tubes.
Quickly access your most commonly used labels, symbols and terms with the “Favorites” key.
Must be suitable for 1. Wires & Cables, 2. Patch Panels & Blocks, 3. Cable Flag, 4. fixed-
length labels, 5. horizontal and vertical wire wrap etc. applications.

Access 100+ industry symbols

Rechargeable Lithium-ion Battery
AC Adapter
Carry Case
With supporting software CD(s)
Labels 18/19mm (Black on Yellow or Black on White)
a. For general labelling
b. Industrial-strength adhesive resists moisture, extreme temperatures, UV light etc.

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

11
 Technical Specification for Online 2KVA UPS

Output
Output power capacity 1.6kWatts / 2.0kVA or better
Nominal Output Voltage 230
Efficiency at Full Load 90%
Output Voltage Distortion Less than 5%
Output Frequency (sync to mains) 47 - 53 Hz for 50 Hz nominal or better
Power Factor Minimum 0.8
Input
Nominal Input Voltage 230V
Input frequency 50 Nominal
Input voltage adjustable range for mains
160V-280VAC or better
operation
Efficiency at Full Load 85% or better
Battery Inbuilt
Maintenance-free sealed Lead-Acid
Battery type battery with suspended electrolyte leak-
proof
Battery capacity should be such that it
Battery Capacity should be able to provide minimum 30
minutes backup at full load.
RS232,USB Com Port, SNMP/Smart
Interface Port(s)
Slot/Intelligent Slot
LED/LCD status display with On Line :
Control panel
On Battery and Overload indicators
Operating Temperature 0 - 40 °C or better
All Standard Accessories supplied with
UPS
Accessories
Any other Accessories requiredinstalling
with the Repeater.
Galvanized anti rust Rack/Stand for the
Rack
UPS.
Preferred Brand APC/NUMERIC/DELTA
Warranty 3 Yrs. OEM onsite warranty

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM(ATSEP) AGM(ATSEP) Jr.Executive (ATSEP)

12
 Technical Specification for Laptop

Processor 8th Generation Intel® Core™ i5-8250U Processor

(6MB Cache, up to 3.4GHz) Or Advance
RAM 8GB or more
RAM Speed 2400MHz or more
RAM Expandability 16GB or more
Operating System Windows 10 Pro (64bit) English
HARD-DISK Type & Capacity SSD/SATA 1TB or more
Hard disk Drive Speed 5400 rpm or more
Graphics Memory 2 GB or more
Wireless Connectivity 802.11ac or advance
Bluetooth Bluetooth 4.0 or advance
ROHS Compliance Yes
USB Port 3.0 2 or more
HDMI port Yes
Monitor Size Minimum 15.6-inch
Resolution (Native) FHD (1920 x 1080) or better
Warranty Minimum 3 Yrs. Onsite
Accessories

Office Microsoft® Office Home and Business 2019 Activated.

Carry Case Included
Anti-Virus Anti-Virus software for 3 yrs.
Portable Hard-disk
SATA/SSD 1 TB (If SATA minimum RPM 7200 & USB
3.0)
External DVD Writer Yes
Serial to USB converter MOXA (Should support RS432,RS422, ,RS485)
Preferred Brand HP/LAPTOP/DELL/ACER

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

13
 Technical Specification for Power Supply cum Battery Charger

AC Input Voltage 170-240 VAC, Single Phase

AC Input Frequency 47-63 Hz
DC Output Voltage 13.5 Volt Nominal
DC Output Current 15.0 Amp Nominal
DC Output Voltage Regulation ≤ ±2 %
Operating Temperature Range 0 - 50° C
Indications AC Power ON, DC Power ON
Protections Short Circuit, Overload, reverse polarity protection
In Case of AC power supply Battery is to be directly floated across the load
failure automatically.

Technical Specification for Level Printer

A portable Industrial Handheld Label printer (Preferred make: DYMO/Brother)

Easily enter text with a familiar computer-style (QWERTY) keyboard or Meet key
ANSI and TIA/EIA-606-A industry labeling standards.
Print 6, 9, 12, 18/19mm or higher width industrial-strength labels in a
variety of materials and colors – plus print directly onto heat-shrink tubes.
Quickly access your most commonly used labels, symbols and terms with
the “Favorites” key.
Must be suitable for 1. Wires & Cables, 2. Patch Panels & Blocks, 3.
Cable Flag, 4. fixed-length labels, 5. horizontal and vertical wire
wrap etc. applications.
Access 100+ industry symbols

Rechargeable Lithium-ion Battery

AC Adapter
Carry Case
With supporting software CD(s)
Labels 18/19mm (Black on Yellow or Black on White)
c. For general labelling
d. Industrial-strength adhesive resists moisture, extreme temperatures,
UV light etc.

Mr. Harikishan Mr. D.Prashad Mr. A.K.Shukla

AGM (ATSEP) AGM (ATSEP) Jr.Executive (ATSEP)

14