MODULATING

FLOAT VALVE

Mustang Series M110-10 or M6110-10 (Globe)

Main Valve Features
- Single Piece Flat Diaphragm Designed
Absolutely no friction to the rubber diaphragm against the
main valve
- Only Three Major Components
Cover, Stem Assembly and Body
- 100% Fusion Bonded Epoxy Coated
NSF 61 Certified Epoxy Coating Internally and Externally
- Simplified Maintenance
No special tools and skill are required

Function
- Maintains a constant liquid level in reservoir
- Opens when level drop
- Closes when level rises

Schematic Operation
The WATTS ACV M110-10 Modulating Float Control Valve
is designed to automatically maintain a constant liquid level
2 in a tank or reservoir. It controlled by a remote mounted Fig.
10-11 Modulating Float Pilot designed to: 1) Modulate Open
P/L (allowing fluid out of the main valve cover chamber) when
X reservoir level decrease, and, 2) Modulate Close (allowing
fluid to fill the main valve cover chamber) when reservoir
ACS level increases.
A decrease in reservoir level causes the valve to modulate
towards an open position, allowing reservoir water level to
increase. An increase in reservoir level cause the valve to
F modulate towards a closed position, allowing reservoir level
YX
to decrease.
1 The Modulating Float Control Pilot is remotely mounted from
the valve, and field connected with 3/8” minimum copper
tubing (not supplied) in accordance with factory piping
schematic.
Components
1. Main Valve F Flo-Clean Strainer
M110-10 is Full Port designed On-Off Float Control Valve
2. Modulating Float Control X Isolation Cocks with M100 Main Valve and M6110-10 are Reduced Port
3 Needle Valve – Adj. Closing Speed Y Strainer
P/L Position Indicator / Limit Switch designed On-Off Float Control Valve with M6100 Main Valve.

Main Valve Dimension (mm)

A B C D E F
VALVE M M M M M M M M Maintenance
SIZE 100 6100 100 6100 100 6100 100 6100 Clearance
25 184 --- 39 --- 140 --- 143 --- 280 480
32 184 --- 39 --- 140 --- 143 --- 280 480
40 184 --- 39 --- 140 --- 143 --- 280 480
50 254 --- 83 --- 165 --- 168 --- 305 510
65 295 --- 95 --- 262 --- 203 --- 360 560
80 345 279 105 105 284 178 232 168 360 560
100 381 353 114 114 362 219 292 232 410 610
150 508 451 140 140 468 295 400 292 610 815
200 645 543 171 171 554 381 508 400 660 860
250 756 660 203 203 594 454 600 508 710 965
300 864 762 241 241 744 533 711 600 760 1120
350 991 --- 267 --- 614 --- 832 --- 860 1220
400 1051 889 298 298 889 654 902 711 1020 1320
450 --- 1219 --- 457 --- 787 --- 900 1220 1420
500 --- 1219 --- 508 --- 787 --- 900 1220 1420
600 --- 1219 --- 610 --- 787 --- 1263 1220 1420

EB-M110 Rev E
Main Valve Material Specifications
Body and Cover - Ductile Iron ASTM A-536
Coating - NSF 61 Certified Fusion Bonded Epoxy
Stem Seat and Disc Guide - Stainless Steel ASTM 316
Nut and spring - Stainless Steel AISI 304
Disc Retainer - Ductile Iron “Epoxy Coated”
Diaphragm Washer - Ductile Iron “Epoxy Coated”
Studs and Nuts - Stainless Steel
Diaphragm - Nylon Reinforced Buna-N ASTM D 2000
Nylon Reinforced EPDM (Optional)
Disc - Buna-N Rubber ASTM D 2000

Main Valve Technical Data Pilot System Specifications

Valve Size - 32 mm to 600 mm Pilot Models - Figure 10-11
Designed Standard - AWWA C530-12 Body Material - Stainless Steel
Operating Pressure - Class 150 Max. 250 PSI (Standard) Rod and Float - Stainless Steel
- Class 300 Max. 500 PSI (Optional) Disc - Buna-N Synthetic Rubber
Operating Temperature - -10 to 90 deg. C (Fluids) Pressure Rating - 100 PSI
End Connection - 50 mm to 600 mm Flanged End Fittings and Tubing - Brass and Copper (Standard)
- 32 mm to 40 mm Screwed End Stainless Steel (Optional)
Flange Standard - PN16, PN25, ANSI 150 or ANSI 300

Installation Guidelines
• Prior to installation, flush line to remove debris.
• Install valve horizontally “in line” (cover facing up), so flow arrow matches flow through the line. Avoid installing valves size
150 mm and larger vertically. Consult factory prior to ordering if installation is other than described.
• Install inlet and outlet isolation valves. Notes: When using butterfly valves, ensure disc does not contact control valve.
Damage or improper valve seating may occur.
• By-pass isolation valve is recommended to install for maintenance purpose without shutting down the systems.
• Provide adequate clearance for valve servicing and maintenance (refer to Dimension Table).
• It is advisable to install a strainer before the control valve to prevent any solid particle from entering the valve body.
• Install pressure gauge to monitor valve inlet pressure.
• Field installed Modulating Float Control Pilot to basic valve using 3/8” diameter minimum copper tubing (not supplied) in
accordance with factory piping schematic.
• Float Control Pilot should be mounted in a field installed “stilling well” for protection against surface turbulence and
interference.

Flow Data Series M 100 / M 6100 (Globe)

Valve Size (mm) 32 40 50 65 80 100 150 200 250 300 350 400 450 500 600
Max. Continuous M100 95 130 210 300 485 800 1850 3100 5000 7000 8500 11100 --- --- ---
Flow Rate GPM M6100 --- --- --- --- 260 580 1025 2200 4100 6400 --- 9230 14360 16500 17250
Max. Intermittent M100 119 161 265 390 590 1000 2300 4000 6250 8900 10800 14100 --- --- ---
Flow Rate GPM M6100 --- --- --- --- 325 720 1280 2750 5100 8000 --- 11500 17950 20625 21560
CV Factor M100 25 30 45 75 100 175 490 770 1200 1750 2125 2890 --- --- ---
USGPM M6100 --- --- --- --- 62 136 229 480 930 1458 --- 2110 3300 3400 3500

Maximum continuous flow based on pipeline velocity of 20 ft. per second.

Maximum intermittent flow based on pipeline velocity of 25 ft. per second.
The Cv factor of a valve is the flow rate in US GPM at 60° F that will cause a 1 psi drop in pressure.
The factors stated are based upon a fully open valve.

Others WATTS ACV Float Control Valve

M 110-13 / M 6110-13 Modulating Float Control Valve with Pressure Sustaining Feature
M 110-AS / M 6110-AS Modulating Float Control Valve with Solenoid (On-Off) Feature
M 110-18 / M 6110-18 On-Off Float Control Valve with Pressure Sustaining Feature

The Automatic Answer to Fluid Control

Represented By: