Scribd
Upload
52 views3 pages

Tuner4TRONIC 2 4 0 Release Notes

Tuner4TRONIC™ version 2.4.0 introduces batch programming for up to 64 DALI luminaires, improved configuration speed, and enhanced graphical interfaces. It is crucial to upgrade all production equipment to this version as production files generated are incompatible with earlier versions. The release notes also highlight known bugs and provide important installation and programming guidelines to avoid errors.

Uploaded by

julia.krol
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
52 views3 pages

Tuner4TRONIC 2 4 0 Release Notes

Tuner4TRONIC™ version 2.4.0 introduces batch programming for up to 64 DALI luminaires, improved configuration speed, and enhanced graphical interfaces. It is crucial to upgrade all production equipment to this version as production files generated are incompatible with earlier versions. The release notes also highlight known bugs and provide important installation and programming guidelines to avoid errors.

Uploaded by

julia.krol
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Tuner4TRONIC™

www.osram.com

Tuner4TRONIC™ 2.4.0
Release Notes
VIII 2015

(2015-08-26)

Important Information:

ATTENTION: PRODUCTION FILE (.OSRTUP) GENERATED WITH THIS VERSION 2.4 ARE NOT
COMPATIBLE WITH PREVIOUS VERSION OF TUNER4TRONIC PRODUCTION, T4T-CMD AND T4T-
DLL.

THE SOFTWARE WILL INTERRUPT ECG PROGRAMMING IN CASE OF DETECTED


INCOMPATIBILITIES, THEREFORE PLEASE UPGRADE ALL YOUR PRODUCTION EQUIPMENT TO
TUNER4TRONIC V2.4 PRIOR USING PRODUCTION FILES.

Please note:
All information in this guide has been prepared with great care. OSRAM, however, does not accept
liability for possible errors, changes and/or omissions. Please check www.osram.com or contact your
sales partner for an updated copy of this guide. This technical application guide is for information
purposes only and aims to support you in tackling the challenges and taking full advantage of all
opportunities the technology has to offer. Please note that this guide is based on own measurements,
tests, specific parameters and assumptions. Individual applications may not be covered and need
different handling. Responsibility and testing obligations remain with the luminaire
manufacturer/OEM/application planner.

VIII 2015 1
Tuner4TRONIC™

Tuner4TRONIC 2.4.0 – What’s new?

 Batch programming (up to 64 DALI Luminaires of the same type)

 Support of Luminaires with more ECGs

 Very fast configuration of single features in DALI ECGs (e.g. only output current) through
selective partial programming

 Several improvements on graphical layout of both interfaces Development and Production


in order to simplify their use even by non-trained users

 Support of new ECGs

 Bugs fixing

Tuner4TRONIC 2.4.0 – known bugs


General Important note
 It is recommended to uninstall the previous version of Tuner4TRONIC before installing this one.
 Windows 8.1: in order to avoid the auto-disconnection of the DALI magic programming
interfaces (which might enter stand-by mode) it is necessary to use the “Win8 DALI magic utility”
available in the installation package; follow the instruction provided with the tool.
 Do not use the engineering samples of DALI magic programming interfaces with white covers
and gray ring, they might cause programming errors; always use the standard ones, which are
fully white.

Tuner4TRONIC Development
 If “new from luminaire” is performed on an ECG that was modified by another software tool, the
parameters may have set out of range and then will not be correctly displayed in the T4T. The
same problem may happen also with some early series of factory new OT 50 2DIMLT2 P
devices.
 DALI short addresses: the possibility to clear the DALI short addresses has been removed. After
programming with Tuner4TRONIC, a possible pre addressed DALI ECG will keep the short
address unchanged. The short address will not be cleared even if this option was set in the
projects created with Tuner4TRONIC previous version 1.2. Short addresses will be cleared in
case of multiple luminaire programming is selected in the programming setup window or in case
the luminaire contains more than one ECG.
 Programming Interface status indicator is always red when the programing interface is not in
use.
This is not indicating any malfunction. In case of trouble with the programming interface please
check it using the “Programming Interface” window available in the Settings menu.
 Emergency Mode settings might change when opening files (.osrtul) generated with T4T-D
version 1.1, please carefully check it.

ECG features:

VIII 2015 2
Tuner4TRONIC™

 If user sets DALI Min Level below physical Min Level, most devices will auto-correct that to the
Physical Min Level, consequently the programming will fail during the verification phase.
Therefore setting DALI Min Level below physical Min Level should be avoided.
 If in the Operating Modes a feature is set and the same feature is not selected to be
programmed, also the Operating Modes setting is not programmed. Make sure to have selected
an operating mode which is also selected to be programmed.

 In Luminaire with two ECG types, there is no warning if an ECG is completely unselected for
programming. Please pay particular attention to this setting.

Tuner4TRONIC Production
 Compatibility with Tuner4TRONIC Production files versions 1.1 and 1.2: in order to use the
production files (.osrtup) created with previous version 1.1 and 1.2, it is necessary to upgrade
them using the T4T-D; see user manuals or the specific instruction available in the installation
package.
NOTE:
o If a Fast Fade Time is set in old projects 1.1 or 1.2, this will be converted to Fade Time
Zero (except for the projects with OTi DALI 50 FAN);
o possible existing DALI short address will not be cleared even if this option was set in
the projects created with Tuner4TRONIC previous version 1.2. Short addresses will be
cleared in case of multiple luminaire programming is selected in the programming setup
window or in case the luminaire contains more than one ECG.

VIII 2015 3

You might also like