Scribd
Upload
18 views2 pages

Model Question Paper 3 Sets

The document consists of model papers for digital systems, each containing various questions related to Boolean algebra, circuit design, and digital components. Topics include minterm and maxterm expressions, universal gates, flip-flops, converters, and memory types. Each set contains theoretical questions and design problems aimed at assessing knowledge in digital electronics.

Uploaded by

shripalsinghlodhi8
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
18 views2 pages

Model Question Paper 3 Sets

The document consists of model papers for digital systems, each containing various questions related to Boolean algebra, circuit design, and digital components. Topics include minterm and maxterm expressions, universal gates, flip-flops, converters, and memory types. Each set contains theoretical questions and design problems aimed at assessing knowledge in digital electronics.

Uploaded by

shripalsinghlodhi8
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Digital Systems

Model Paper - Set 1


1. a) Define and explain the concept of minterm and maxterm expressions in Boolean
algebra. b) State and prove DeMorgan's theorems with truth tables.
2. a) What are universal gates? Implement XOR and XNOR gates using only NAND
gates. b) Design a 4-bit binary comparator circuit and explain its operation.
3. a) Draw and explain the working of CMOS inverter. Compare it with TTL inverter. b)
Design an astable multivibrator using 555 timer and explain its operation.
4. a) Design a 4-bit synchronous down counter using JK flip-flops. b) Explain the
working of bidirectional shift register with diagram.
5. a) Explain the working principle of dual slope type Analog to Digital Converter. b)
Design a Sample and Hold circuit using op-amp and explain its operation.
6. a) Simplify the following Boolean function using K-map: F(A,B,C,D) =
Σm(0,2,4,6,8,10,12,14) + d(1,5,9,13) b) Implement a full subtractor using NAND
gates only.
7. a) Explain the operation of edge-triggered D flip-flop with timing diagram. b)
Describe different types of ROM memories (PROM, EPROM, EEPROM).
8. Write short notes on any three: i) Gray code and its applications ii) Ring and Johnson
counters iii) BCD adder iv) Half and Full adders

Model Paper - Set 2


1. a) Explain the procedure to convert given Boolean expression into canonical forms. b)
Prove the following Boolean identities:
o (A + B)(A + C) = A + BC

o AB + A'C + BC = AB + A'C

2. a) Implement basic logic gates using only NOR gates with truth tables. b) Design a
BCD to Excess-3 code converter using logic gates.
3. a) Explain the working principle of TTL NAND gate with totem-pole output. b)
Design a bistable multivibrator using transistors.
4. a) Design a mod-6 synchronous counter using T flip-flops. b) Explain the working of
universal shift register with diagram.
5. a) Explain the working of flash type Analog to Digital Converter. b) Design a 4-bit
weighted resistor type Digital to Analog Converter.
6. a) Minimize the following function using K-map: F(A,B,C,D) =
Σm(1,3,5,7,9,11,13,15) b) Design a 2-bit magnitude comparator.
7. a) Explain the working of master-slave JK flip-flop with timing diagram. b) Write
detailed notes on different types of RAM memories (SRAM, DRAM).
8. Write short notes on any three: i) Multiplexer and Demultiplexer ii) Priority encoder
iii) Decade counter iv) Crystal oscillator

Model Paper - Set 3


1. a) Explain the difference between combinational and sequential circuits with
examples. b) State and prove consensus and absorption theorems.
2. a) Design a 4:1 multiplexer using basic gates and implement Boolean function using
multiplexer. b) Design a 4-bit carry look-ahead adder.
3. a) Compare ECL, TTL, and CMOS logic families in terms of speed, power
dissipation, and noise margin. b) Design a voltage-controlled oscillator using 555
timer IC.
4. a) Design a sequence detector to detect sequence "1011" using Moore machine. b)
Explain the working of 4-bit SIPO shift register with timing diagram.
5. a) Explain the working principle of counter type Analog to Digital Converter. b)
Design an instrumentation amplifier using three op-amps.
6. a) Minimize the following function using K Map method: F(A,B,C,D) =
Σm(0,1,3,5,7,8,9,11,13,15) b) Implement 4-bit binary to Gray code converter.
7. a) Design a 4-bit synchronous up/down counter using JK flip-flops. b) Explain
different types of hazards in digital circuits and their elimination.
8. Write short notes on any three: i) PLAs and PALs ii) Barrel shifter iii) Wien bridge
oscillator iv) Race around condition in JK flip-flop

You might also like