PC1616/PC1832/PC1864 v4.

6 NA
Installation Guide

WARNING: This manual contains information on limitations regarding product use and function and information on
the limitations as to liability the manufacturer. The entire manual should be read carefully.
 Table of Contents
Guidelines for Locating Smoke Detectors and CO Detectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Chapter 1 Installation & Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Keybus Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Zone Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Zone Expanders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4 Bell Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.5 AUX Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.6 PGM Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.7 Carbon Monoxide Detector Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.8 Telephone Line Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.9 Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.10 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.11 AC Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.12 RFK5500 and RFK5564 Easy Wireless Enrollment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 2 User Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Away Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Stay Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 [✱] Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.5 Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 3 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Template Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 DLS Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Advanced Keypad Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 4 Programming Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 5 Programming Worksheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.1 Index to Programming Worksheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Appendix A: Reporting Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Appendix B: UL Listed Commercial and Residential Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Appendix C: SIA False Alarm Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Appendix D: Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Appendix E: Template Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Appendix F: Communicator Format Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
SAFETY INSTRUCTIONS FOR SERVICE PERSONNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
FCC COMPLIANCE STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

i
PowerSeries - PC1616/PC1832/PC1864

Guidelines for Locating Smoke Detectors and CO Detectors

The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating
and installing smoke and carbon monoxide alarms.
Smoke Detectors
Research indicates that all hostile fires in homes generate smoke to a greater or lesser extent. Detectable quantities of smoke precede detectable
levels of heat in most cases. Smoke alarms should be installed outside of each sleeping area and on each level of the home.
DSC recommends that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that should be
protected include: the basement; bedrooms, especially where smokers sleep; dining rooms; furnace and utility rooms; and any hallways not
protected by the required units.
On smooth ceilings, detectors may be spaced 9.1m (30 feet) apart as a guide. Other spacing may be required depending on ceiling height, air
movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-02 or other appropri-
ate national standards for installation recommendations.
• Do not locate smoke detectors at the top of peaked or gabled ceilings; dead air space in these locations may prevent smoke detection.
• Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector may prevent smoke from
entering the unit.
• Do not locate detectors in areas of high humidity.
• Do not locate detectors in areas where the temperature rises above 38oC (100oF) or falls below 5oC (41oF).
• Smoke detectors should always be installed in USA in accordance with Chapter 11 of NFPA 72, the National Fire Alarm Code: 11.5.1.1. :
Where required by applicable laws, codes, or standards for a specific type of occupancy, approved single- and multiple-station smoke alarms
shall be installed as follows:
(1) In all sleeping rooms and guest rooms.
(2) Outside of each separate dwelling unit sleeping area, within 6.4 m (21 ft) of any door to a sleeping room, the distance measured along a path of travel.
(3) On every level of a dwelling unit, including basements.
(4) On every level of a residential board and care occupancy (small facility), including basements and excluding crawl spaces and unfinished attics.
(5) In the living area(s) of a guest suite.
(6) In the living area(s) of a residential board and care occupancy (small facility).

Figure 3
Figure 1 Figure 2

Figure 3a Figure 4
CO Detectors
Carbon monoxide gas moves freely in the air. The human body is most vulnerable to the effects of CO gas
during sleeping hours. For maximum protection, a CO alarm should be located outside primary sleeping BEDROOM
areas or on each level of your home. Figure 5 indicates the suggested locations in the home. The elec-
tronic sensor detects carbon monoxide, measures the concentration and sounds a loud alarm before a BEDROOM BEDROOM
potentially harmful level is reached. GARAGE
GROUND KITCHEN
Do NOT place the CO alarm in the following areas: FLOOR
• Where the temperature may drop below -10ºC or exceed 40 ºC.
BASEMENT
• Near paint thinner fumes.
• Within 5 feet (1.5 meters) of open flame appliances such as furnaces, stoves and fireplaces. CARBON MONOXIDE DETECTOR
• In exhaust streams from gas engines, vents, flues or chimneys. Figure 5
• In close proximity to an automobile exhaust pipe; this will damage the detector.

ii
 Chapter 1 Installation & Wiring

Chapter 1 Installation & Wiring

This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616,
PC1832, and PC1864 control panels.

All necessary information required to meet UL Listing requirements is included in this document.

Technical Summary
FEATURES PC1616 PC1832 PC1864
OUT Of THE BOX On-board Zones 6 8 8

Qty 1 ❑ Cabinet Hardwired Zones 16 (1xPC5108) 32(3xPC5108) 64 (7xPC5108)

Qty 1 ❑ PC Module
Qty 1 ❑ Installation Guide Wireless Zones 32 32 64
Qty 1 ❑ User Manual
Keypad Zone Support ✔ ✔ ✔
Qty 2 ❑ Cabinet Label
Qty 1 ❑ Cabinet Door Plug On-board PGM PGM 1 - 50mA PGM 1 - 50mA PGM 1, 3, 4 - 50mA
Qty 5 ❑ Standoffs Outputs PGM 2 - 300mA PGM 2 - 300mA PGM 2 - 300mA
Qty 16 ❑ 5.6K Resistors
Qty 1 ❑ 2.2K Resistor 8x50mA (PC5208) 8x50mA (PC5208) 8x50mA (PC5208)
PGM Expansion
Qty 1 ❑ 1.0K Resistor 4x500 mA (PC5204) 4x500 mA (PC5204) 4x500 mA (PC5204)
Qty 1 ❑ Grounding Kit Keypads 8 8 8

Partitions 2 4 8

SPECIFICATIONS User Codes 47 + Master Code 71 + Master Code 94 + Master Code

Temp Range . . . 0°C-49°C (32°F-120°F) Event Buffer 500 Events 500 Events 500 Events
Humidity (Max) . . . . . . . . . . . . . 93%R.H.
Power Supply . . 16.5VAC/40VA @60Hz Transformer Required 16.5VAC/40VA 16.5VAC/40VA 16.5VAC/40VA
Current Draw (Panel) . . . .110mA (nom.)
Aux+ Output . . . . 11.1-12.6VDC/700mA Battery Required 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr 4Ah / 7Ah/14AHr
Bell Output. . . . . . 11.1-12.6VDC/700mA Bell Output 12V/700 mA (cont) 12V/700 mA (cont) 12V/700 mA (cont)

COMPATIBLE DEVICES

Keypads (Backward compatible with all PowerSeries keypads) Modules

PK55XX Keypad..............................................................125mA (max.) TL-250/TL300 Communicator ............................................ 275/350mA

RFK55XX Keypad ...........................................................135mA (max.) GS2060/GS2065 (GPRS/GSM only)........................................... 65mA
LCD5511 Fixed Message LCD Keypad ........................... 85mA (max.) GS2060-SM (GPRS only) ........................................................... 90mA
LED5511Z 8-zone LED Keypad .....................................100mA (max.) TL260GS/TL265GS (Ethernet/GPRS) ...................................... 100mA
TL260-SM (Ethernet only) ......................................................... 100mA
Cabinets TL260GS-SM (Ethernet/GPRS only)......................................... 120mA
PC5003C......................................... 222x298x78mm (11.3x11.7x3.0in) PC5100 2-wire Interface............... 40mA plus devices to 170mA max.
PC500C (residential burg only) ......... 213x235x78mm (8.4x9.25x3.0in) RF5132-433 Wireless Receiver ............................................... 125mA
PC4050CAR (UL commercial burg).. 305x 376x124mm (12.0x14.8x4.9in) RF5108-433 Wireless Receiver ............................................... 125mA
CMC-1 (UL commercial burg) ......... 287x297x76mm (11.3x11.7x3.0in) PC5108 Zone Expander ............................................................. 30mA
Suttle, SAE 14 ......................... 355.6 x 362x 95mm (14x14.25x 3.75in) PC5200 Power Supply ................................................................ 20mA
Suttle, SAE 21 ......................... 533.4 x 362x 95mm (21x14.25x 3.75in) PC5204 Power Supply with 4 Programmable Outputs................ 30mA
Suttle, SAE 28 ......................... 711.2 x 362x 95mm (28x14.25x 3.75in) PC5208 Low Current Programmable Output Module ................. 50mA
Suttle, SAE 42 ....................... 1066.8 x 362x 95mm (42x14.25x 3.75in) Escort5580 Telephone Interface Module ................................... 130m
*The T-Link TL-150 is not UL/ULC listed

Classified in Accordance with ANSI/SIA CP-01-2000 (SIA-FAR)

INSTALLATION
Begin the installation by mounting additional modules in the cabinet using the stand-offs provided, then mount the cabinet in a dry, protected
area with access to unswitched AC power. Install hardware in the sequence indicated in the following pages. Do NOT apply power until instal-
lation is complete.
All wiring entry points are designated by arrows. All circuits are classified UL power limited except for the battery leads. Minimum 1/4”
(6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and connections.

1
PowerSeries - PC1616/PC1832/PC1864

PC1616/1832/1864 Wiring Diagram

North America Only

POWER LIMITED

PC Board Stand Off

1. Inser t Stand off into cabinet
mounting hole in the
Cable Tie (not supplied) recommended
desired location. Snap-in-
place. Cabinet

2. Position circuit board

mounting holes over DSC
UA503
standoffs. Press firmly Primar y:120VAC/60Hz.
on board to snap-in-place. Secondary: 16.5VAC 40VA
PC1616/1832/1864

220
DSCPTD 1640U
Class II Transformer
WARNING:
NOTE: Do not connect High Voltage. Disconnect AC Power
transformer to receptacle and telephone lines before servicing
controlled by a switch

PC1864 PC1864
Only PC1832
Only
CON1
BAT+BAT-
TB-2
AUX+ BELL+ PGM1 PGM3 RING R-1
AC AC AUX- BELL- RED BLK YEL GRN PGM2 PGM4 Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 EGND TIP T-1

230 VAC/50 Hz International

CON1 See ground wiring

diagram in the Installation
BAT+BAT-
AC AC

section of this manual

12V / 7 AHr 12V / 7 AHr

To EGND BLACK
Terminal
16.5VAC/40VA
RED

DSC Model BD7-12

NON-POWER LIMITED or equivalent

Battery
StandbyTime:
24Hrs min.
FUSE

WARNING: Incorrect connections may result in PTC failure or improper operation.

Inspect wiring and ensure connections are correct before applying power.
Incorrect connection of batteries may result in battery rupture or Fire Hazard.
Do NOT allow metal objects to connect the Positive and Negative Terminals.
Ensure that batteries are connected with correct polarity [Red to (+), Black to (-)].
Failure to comply with this may result in battery rupture and/or Fire Hazard.
All circuits are classified for UL Installations as Power Limited/Class II Power Limited
IMPORTANT:
except for battery leads which are not power limited.
a)This equipment, Alarm Controller PC1616/1832/1864 shall Do NOT route any wiring over circuit boards. Maintain at least 1"(25.4mm) separation.
be installed and used within an environment that provides the A minimum of 1/4" (6.4mm) separation must be maintained at all points between
pollution degree max 2 and over voltages category II power limited wiring and all other non-power limited wiring.
NON-HAZARDOUS LOCATIONS, indoor only. The equipment is
FIXED and PERMANENTLY connected and is designed to be UA503 REV XX DSC
installed by ser vice persons only; [ser vice person is defined as a
person having the appropriate technical training and experience
necessar y to be aware of hazards to which that person may be
PC1616/1832/1864
220

exposed in performing a task and of measures to minimize the risks

to that person or other persons.]

b)The connection to the mains supply must be made as per the local
authorities rules and regulations.
An appropriate disconnect device must be provided as par t of the
building installation. Where it is not possible to rely on identification of
PC-LINK
the neutral in the AC Mains supply the disconnecting device must
disconnect both poles simultaneously (line and neutral). The device
shall disconnect the supply during servicing.
AUX+ and Keybus (Red) are Internally Connected
Total current draw from Keypads, PGM Outputs and 10
c)The equipment enclosure must be secured to the building structure Aux circuits must not exceed 700mA
before operation.
Internally Connected
e)Internal wiring must be routed in a manner that prevents:
- Excessive strain on wire and on terminal connections;
- Loosening of terminal; connections;
- Damage of conductor insulation PC1864 PC1864
Only PC1832
Only
f) Disposal of the used batteries shall be made according to the waste CON1
TB-2
recovery and recycling regulations applicable to the intended market. BAT+BAT-
AC AC + AUX - + BELL - RED BLK YEL GRN 1 PGM 2 3 PGM 4 Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 EGND RING TIP R-1 T-1

Keybus PGMs Zones Telephone

DG009606

WARNING:
High Voltage. Disconnect AC Power
and telephone lines before servicing

2
 Chapter 1 Installation & Wiring

1.1 Keybus Wiring

The 4-wire KEYBUS (red, black, yellow and green) is the communication connection between the control panel and all modules. The 4 KEY-
BUS terminals of all modules must be connected to the 4 KEYBUS terminals of the main control panel.
The following rules must be followed when wiring the Keybus:
• Minimum 22 AWG wire, max. 18 AWG (2-wire twisted preferred)
• Do not use shielded wire 150’ (46m)
• Modules can be home run, connected in series or T-tapped, provided that 500’ (152m)
150’ (46m)
the maximum wire distance from the control panel to any module does not
exceed 1,000 feet (305m) CONTROL
• No more than 3,000 feet (915m) of wire can be used in total PANEL 500’ (152m)

1.2 Zone Wiring

Zones can be wired for Normally Open or Normally Closed contacts, with Normally Closed Loops - Do NOT use for UL Installations
Single-End-of-Line (SEOL) or Double End-of-Line (DEOL) resistors.
Observe the following guidelines:
• For UL Listed Installations use SEOL or DEOL only.
• Minimum 22 AWG wire, maximum 18 AWG
• Do not use shielded wire
• Wire run resistance shall not exceed 100 Refer to the chart below:
Single End-of-Line Resistor Wiring
Burglary Zone Wiring Chart
Wire Maximum Wire Length to
Gauge End-of-Line Resistor (ft/meters)
22 3000 / 914
20 4900 / 1493
19 6200 / 1889
18 7800 / 2377
Figures are based on maximum wiring resistance of 100

• [001]-[004] Selects Zone Definition

Double End-of-Line Resistor Wiring
• [013] Opt [1] Selects Normally Closed or EOL resistors
• [013] Opt [2] Selects SEOL or DEOL resistors
• [101]-[108] Opt [14], [15], [16] Selects Normally Closed SEOL or DEOL
for on-board zones (PC1832/1864, Zone 1-8; PC1616, Zones 1-6)

Zone Status - Loop Resistance/Loop Status

• Fault - 0 (shorted wire/loop) • Tamper - infinite (broken wire, open)
• Secure - 5600 (contact closed) • Violated - 11,200 (contact open)

1.3 Zone Expanders

Zone expanders add zones in groups Module Zones
of eight to the Alarm system. Module Jumpers Assigned
jumpers J1, J2, J3 are required to J1 J2 J3
assign zones to these modules. ON ON ON Zones Disabled
Jumper settings for PC5108 v2 are OFF ON ON Zones 09-16
shown here. ON OFF ON Zones 17-24
• PC5108 v1.0 supports first 32 OFF OFF ON Zones 25-32
zones only. ON ON OFF Zones 33-40
• PC5700 enrolls as two modules OFF ON OFF Zones 41-48
• Do NOT use PC5108 v1 and ON OFF OFF Zones 49-56 Refer to the associated installation sheet for Jumper locations
PC5108 v2 on the same panel. for the PC5108 v1 and PC5700.
OFF OFF OFF Zones 57-64
1.4 Bell Wiring
These terminals supply 700mA of current at 12VDC for commercial installations and 11.1-12.6VDC for
residential installations (e.g. DSC SD-15 WULF). To comply with NFPA 72 Temporal Three Pattern
requirements: Program [013] Opt [8] ON. Note that Steady, Pulsed alarms are also supported.
The Bell output is supervised and power limited by 2A PTC. If unused, connect a 1000 resistor across
Bell+ and Bell- to prevent the panel from displaying a trouble. See [✱][2].

3
PowerSeries - PC1616/PC1832/PC1864

1.5 AUX Power Wiring

The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LEDs, etc. If the total current required
exceeds 700mA an additional power supply is required (e.g., PC5200, PC5204). See list below.
Min/max operating voltages for devices, sensors and modules is 9.5VDC - 14VDC.

1.6 PGM Wiring

PGMs switch to ground when activated from the control panel. Connect the For current levels greater than 300mA, a relay is required.
positive side of the device to be activated to the AUX+ Terminal. Connect the PGM2 can also be used for 2-wire smoke detectors.
negative terminal to the PGM. NOTE: Use SEOL resistors on fire zones only.
Current output is as follows: LED output with current limiting resistor and optional relay
• PGM 1, 3, 4 50mA driver output
• PGM 2 300mA

2-Wire Smoke Detectors Initiating Circuit

• Style B (Class B), Supervised, Power Limited
• UL Compatibility Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PC18-1
• DC Output Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.8-13.8 VDC
• Detector Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2mA (MAX)
• Single End-of-Line (SEOL) Resistor. . . . . . . . . . . . . . . . . . . . . . . . .2200
• Loop Resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 (MAX)
• Standby Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1020
• Alarm Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570 (MAX)
• Alarm Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89mA (MAX)

UL Compatibility ID For FSA-210B Series is: FS200

NOTE: For ULC Listed installations use FSA-210A and FSA-410A series. 4-Wire Smoke Detectors

RM-1/RM-2 POWER LOOP

SUPERVISORY RELAY
12VDC

2200 Ohm
END-OF-LINE ALARM
RESISTOR INITIATING
EOLR-3 LOOP
RESISTANCE
100 Ohm

EOLR-2
END-OF-LINE
RESISTOR
5600 Ohm, 0.5W

1.7 Carbon Monoxide Detector Wiring

CO DETECTOR The following hardwired CO Detector models can be used
POWER ALARM TROUBLE with PC1616/PC1832/PC1864 v4.5 (and higher) control
- + NC C NO NC C NO panels:
• Potter Model CO-12/24, UL File E321434
PC1616/1832/1864 • Quantum Model 12-24SIR, UL File E186246
• NAPCO Model FW-CO12 or FW-CO1224, UL File E306780
• System Sensor Model CO1224, UL File E307195
AUX
+-

NOTE: For multiple unit connections, the leads between CO detec-

tors need to be broken. The power supervision relay has to be pow-
SEOL
ered from the last detector in the loop.
ANY ANY

RESISTOR
COM Z

ZONE (5600 ohm)

INPUT Wireless CO detectors are also available. When installing
-
DG009477

wireless CO detectors, use only DSC model WS4913. A DSC

+

ALARM
(SEOL TYPE 41) wireless receiver model RF5132-433 v5.1 (and higher) or DSC
INITIATING
RM-1/RM-2
LOOP keypad receiver models RFK55XX-433 (xx= 00/01/08/16/64)
RESISTANCE v1.2 (and higher) are required when installing wireless CO
POWER LOOP 100 ohm
SUPERVISORY detectors. For more details on either the WS4913 CO detector
RELAY or the receivers, please refer to their respective installation
(12VDC, 35mA) manuals.

4
 Chapter 1 Installation & Wiring

1.8 Telephone Line Wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ-31x
T-1 BRN
Connector as indicated. For connection of multiple devices to the telephone
R-1 GRA
line, wire in the sequence indicated. Use 26 AWG wire minimum for wiring. TIP GRN

Telephone format is programmed in option [350]. RING RED

RJ-31X
Telephone Call Directions are programmed in options [351]-[376].

1.9 Ground
Ground Installation
Tighten nut to break paint and make
good connection to the cabinet

1.10 Battery
Standby Battery Guide A sealed, rechargeable, lead acid battery or gel type battery is required to
Battery Charging Current: 400 mA meet UL requirements for power standby times.
Battery Standby NOTE: UL Residential/Commercial Burglary installations require 4Hrs
Size 4Hr 24Hr of standby battery time.
--------------------------------------------------------- NOTE: UL/ULC Residential Fire & Health Care installations require 24
4Ahr 700mA ---- Hrs of standby battery time. ULC Commercial Burglary and Fire moni-
7Ahr 700mA 180mA toring installations require 24Hrs of standby battery time plus 5 minutes
14Ahr 700mA 470mA of alarm condition.
NOTE: Battery capacity will deterio-
rate with age and the number of
charge/discharge cycles. Replace
every 3-5 years.
1.11 AC Wiring
AC Wiring (UL Listed Installations)
Primary: 120VAC/60Hz./0.33A
Secondary: 16.5VAC/40VA DSC PTD1640U, DSC PTC1640U,
DSC PTD1640U-CC Plug-in, Class 2 Transformer.
NOTE: Use DSC PTD1640 for Canadian installations.

For UL Listed installations, do NOT connect transformer to a receptacle controlled by a switch.

1.12 RFK5500 and RFK5564 Easy Wireless Enrollment Procedure

1. Enter [ ✱ ][8][Installer Code][898]. The LCD displays the following: “Wireless Enrollment Mode.”
2. Place the wireless device in the desired location.
3. Activate the device as described in the associated installation sheet. The electronic serial number (ESN) is displayed.
4. Press [ ✱ ] to confirm the ESN. If the serial number is incorrect, press [#] to discard it, and repeat this step. After successful confirmation of
the serial number, the system prompts for the zone number. The next available zone is displayed.
5. Enter a zone number (01-64) then press [ ✱ ] to accept. The next available zone is preloaded.
NOTE: Only one device may be enrolled in each zone. If a zone already has a device enrolled, press [*] to overwrite the zone or [#] to enter
another zone number.
6. After successful entry of the zone number, the system prompts for the zone type. (The recommended zone type is displayed). Press [ ✱ ] to
accept the zone type or enter:
Device Type Zone Definition
2 Door/Window Contact [01] Delay 1
3 PIR or Glassbreak [05] Interior, Stay-Away
4 Smoke Detector [88] Standard 24 Hr Fire (Wireless)
5 Pendant [16] 24 Hour Panic
8 CO Detector [81] 24 Hour CO Detection

5
PowerSeries - PC1616/PC1832/PC1864

Chapter 2 User Commands

Any system keypad can be used to program or perform any keypad command. LED keypads use status and zone indicator lights to represent
alarm functions and status. The LCD keypad displays the description and status indicator lights represent alarm functions and status. This section
describes basic keypad commands.

Press the [#] key to reset the keypad if an error has been made entering user codes or keypad commands.

2.1 Away Arming

The Ready light must be ON to arm the system. If the Ready light is OFF, ensure that all protected doors and windows are secure or
bypassed. To arm the system in the Away mode, either press and hold the Away function button for 2 seconds or enter a valid user code and
leave the premises through a door programmed as Delay. Upon arming, the Armed light will turn ON. If a user code was used to arm the sys-
tem and Stay/Away zones are programmed, the Bypass light will turn ON and will turn OFF when a door programmed as Delay is violated.
If the Audible Exit Delay option is enabled, the keypad will beep once every second during the exit delay (and three times a second during
the last 10 seconds) to prompt the user to leave.

2.2 Stay Arming

The Ready light must be ON to arm the system. If the Ready light is OFF, ensure that all protected doors and windows are secure or
bypassed. To arm the system in the Stay mode, either press and hold the Stay function button for 2 seconds or enter a valid user code and stay
within the premises (do NOT violate a door programmed as Delay). Upon arming, the Armed light and Bypass light will turn ON. If the Stay
function button is used, the keypad will not beep during the exit delay. If a user code was used, the keypad will beep if the Audible Exit
Delay option is enabled.

2.3 Disarming
The user must enter through a door programmed as Delay. Upon entering, the keypad will emit a steady tone (and emit a pulsing tone during
the last 10 seconds of entry delay) to prompt the user to disarm the system. Enter a valid user code to disarm the system. If an alarm occurred
while the panel was armed, the Memory light and the zones that went into alarm will be flashing (LED keypad) or the keypad will display
‘Alarm in Memory’ (LCD keypad). Press the [#] key to return the keypad to the Ready state.

2.4 [✱] Commands

The following is a list of the [✱] commands available and a description of each:
[✱][1] Bypass (disarmed state)/Reactivate Stay/Away Zones (armed state)
[✱][2] Display Trouble Conditions
[✱][3] Display Alarm Memory
[✱][4] Door Chime Enable/Disable
[✱][5] User Code Programming
[✱][6] User Commands
[✱][7][x] Command Functions 1 – 4
[✱][8] Installer Programming
[✱][9][code] No-Entry Arming
[✱][0] Quick Arm (disarmed state)/Quick Exit (armed state)

[✱][1] Bypass/Re-activate Stay/Away Zones

LED Keypad
Press [✱][1] to enter the bypass mode. If the Code Required for the Bypass option is enabled, enter a valid user code. The Bypass light will
flash. The keypad will turn ON the corresponding zone light to indicate a zone is bypassed. To bypass or unbypass a zone, enter the 2-digit
zone number. Once the correct zones are bypassed, press [#] to exit. The Bypass light will be ON if any zones are manually bypassed.
LCD Keypad
Press [✱][1] to enter the bypass mode. If the Code Required for the Bypass option is enabled, enter a valid user code. The keypad will dis-
play ‘Scroll to View Zones’. The keypad will display the programmed zone labels for the zones and include the letter ‘O’ in the bottom right
corner if the zone is violated, or the letter ‘B’ if the zone is bypassed. Scroll to the appropriate zone and press the [✱] key to change the
bypass status (or enter the 2-digit zone number). Once the correct zones are bypassed, press [#] to exit.

Additional Bypass Commands:

Bypass Recall: Press [99]. The keypad will recall the last group of zones that were bypassed
Clear Bypass: Press [00]. The keypad will clear the bypass on all zones.
Save Bypass: Press [95]. The keypad will save which zones are manually bypassed.
Recall Save: Press [91]. The keypad will recall the bypassed zones that were saved.

Hold-up Zones cannot be assigned to bypass groups.

Re-activate Stay/Away Zones: Press [✱][1] when the system is armed in the Stay mode to change the armed status to Away mode. The
system will add the Stay/Away zones back into the system after the exit delay time expires.

6
 Chapter 2 User Commands

[✱][2] Trouble Display

Refer to Appendix D – Troubleshooting Guide, for troubleshooting assistance and a detailed description of all trouble conditions.
When powering up the system for the first time, or in the event of a loss of power (including battery removal), a Loss of Clock trouble will
appear on the display. Press [8] on any keypad or [✱] on any PK series keypad to access the time and date programming menu.

[✱][3] Alarm Memory Display

The Memory light will be ON if an alarm occurred during the last armed period. Press [✱][3]. The Memory light will flash and the keypad
will display the zones that went into alarm.

To clear the Memory light, arm then disarm the system.

[✱][4] Door Chime Enable/Disable

Press [✱][4]. The keypad will emit 3 rapid beeps if the door chime feature is now enabled and a steady 2-second tone if it is now disabled.
The same function can be performed by pressing and holding the Chime function button for 2 seconds.

[✱][5] Program User Codes

The following table identifies available user codes:
Code Type Function
[01]-[39], [41]-[95] General User Codes Arm, disarm
[40] Master Code All functions

Programming User Codes:

LED Keypad:
Press [✱][5] followed by the Master Code. The Program light will flash. The keypad will turn ON the corresponding zone lights to indicate if
any user codes are programmed. To add or change a user code, enter the 2-digit user code to be programmed. The zone light will flash. Enter
a new 4 or 6-digit user code or press [✱] to delete the user code. After the user code is programmed or deleted, the zone light corresponding to
the user code will stop flashing. To add or change another user code, enter the 2-digit user code to be programmed or press [#] to exit.
LCD Keypad:
Press [✱][5] followed by the Master Code. The keypad will display the first user (user 01) and include the letter ‘P’ in the bottom, right cor-
ner if the user code is programmed. Scroll to the appropriate user and press the [✱] key to program the user (or enter the 2-digit user num-
ber). Enter a new 4 or 6-digit user code or press [✱] to delete the user code. After the user code is programmed or deleted, scroll to another
user or press [#] to exit.

Programming Partition Assignment:

Press [✱][5] followed by the Master Code or Supervisor Code. Press [98] followed by the 2-digit user to change to the partition assignment.
The keypad will turn ON the corresponding zone light to indicate which partition(s) the user is assigned to. For example, if zone light 1 is
ON, the user is assigned to partition 1. To change the partition assignment, press the number corresponding to the partition. Once the correct
partitions are assigned to the user, press [#] to exit. To change the partition assignment for another user, press [98] followed by the 2-digit
user number. When finished, press [#] to exit.

Programming User Attributes:

Press [✱][5] followed by the Master Code or Supervisor Code. Press [99] followed by the 2-digit user to change to the user attributes. The
keypad will turn ON the corresponding zone light to indicate which attributes are assigned to the user.
Light [1] User can enter User Code Programming section with this code
Light [2] Duress Reporting Code is sent whenever this code is entered
Light [3] User can manually bypass zones
Light [4] User can access the Escort5580 module remotely
Light [5] For Future Use
Light [6] For Future Use
Light [7] The panel will squawk when the user arms/disarms
Light [8] One-time use code – Can disarm the system once per day and is reset at midnight.
To change the user attributes, press the number corresponding to the attribute. Once the correct attributes are assigned to the user, press [#] to
exit. To change the user attributes for another user, press [99] followed by the 2-digit user number. When finished, press [#] to exit.

7
PowerSeries - PC1616/PC1832/PC1864

[✱][6] User Functions

Press [✱][6] followed by the Master Code, then press the number corresponding to the following functions:
[1] Program Time and Date: Enter the time and date using the following format [HH:MM] [MM/DD/YY]. Program the time using the
twenty-four-hour system (e.g., 8:00 PM = 2000 hours).
[2] Auto-arm/Auto-disarm Enable/Disable: The keypad will emit 3 rapid beeps if the Auto-arm/Auto-disarm feature is now enabled and a
steady 2-second tone if it is now disabled.
[3] Auto-arm Time/Day: Press the number corresponding to the day of the week (1=Sunday, 2=Monday etc.) followed by the auto- arm
time (HH:MM). Program the time using the twenty-four-hour system (e.g., 8:00 PM = 2000 hours).
[4] System Test: The panel will perform the following: activate the bell output, keypad buzzer and all keypad status lights for 2 seconds,
test the backup battery and transmit a reporting code to the central station (if programmed).
[5] Enable DLS: The panel will temporarily enable DLS for 1 or 6 hours depending on programming (see Sect [702] opt.[7]).
[6] User Initiated DLS: The panel will attempt to call the DLS computer.
[7] -[8] For Future Use

If using LCD keypads, scroll to the desired option then press [✱].

Additional Alphanumeric Keypad Functions:

When scrolling through the list of available functions, the following additional functions are available:
Event Buffer: Used to view the 500-event panel log
Brightness Control: Used to adjust the display backlighting level for optimal viewing
Contrast Control: Used to adjust the display contrast level for optimal viewing
Buzzer Control: Used to adjust the keypad buzzer tone for optimal sound

[✱][7][x] Command Output (1-4)

Press [✱][7][x]. If the Command Output Code Required option is enabled, enter a valid user code. The panel will activate any PGM output
assigned to the command output.

[✱][8] Installer Programming

Press [✱][8] followed by the Installer Code to enter Installer Programming. Refer to the ‘How to Program’ section for more information.

[✱][9][User Code] No-Entry Arming

Press [✱][9] followed by a valid user code. The system will arm in the Stay mode, and after the exit delay expires, it will remove entry delay.
All zones programmed as Delay will function like Instant zones. The system will flash the Armed light to indicate that the system is armed
with no entry delay.

[✱][0] Quick Arm/Quick Exit

Quick Arm: When disarmed, press [✱][0] to arm the system. The system will arm as if a valid user code was entered.
Quick Exit: When armed, press [✱][0] to activate Quick Exit. The system will allow a single zone programmed as Delay to be violated a
single time during the following 2-minute time period without changing the status of the system.

2.5 Function Keys

Keypads have 5 programmable one-touch function buttons located in a column down the right side of the keypad. These buttons can also be
activated by pressing and holding numbers [1] through [5] respectively for 2 seconds. The default for these function buttons on the PK series
keypads are as follows:
[1] Stay Arm
[2] Away Arm
[3] Chime Enable/Disable
[4] Fire Reset – Command Output 2
[5] Quick Exit

8
 Chapter 3 Programming

Chapter 3 Programming
This chapter provides the information necessary to program all the features required for a basic system, as well as common applications.

3.1 Template Programming

Selecting [✱][8] [Installer Code] [899] displays the current 5-digit template programming code. Refer to Appendix E - Template Programming for
a detailed description of available templates and corresponding 5-digit codes. After entering a valid 5-digit template programming code, you will
be prompted to enter the following in the sequence indicated below:
This feature requires a PK55xx or RFK55xx series keypad, v.1.1 or higher.

1. Central Station Telephone Number, enter 32-Character Telephone number

Program the required Central Station phone number. Press [#] to complete your entry if less than 32 digits. This phone number will be
entered into the programming option [301].
2. Central Station Account Code, enter 6-digit code
Program the required Central Station Account Code. Press [#] to complete your entry if less than 6 digits. This account code will be entered
into the programming option [310].
3. Partition Account Code, enter 4-digit code
This programming section will only be prompted if Contact ID has been selected as a communications format. Program the required Parti-
tion Account Code. This Partition account code will be entered into the programming option [311].
4. DLS Access Code, enter 6-digit code
Program the required DLS Access Code. Press [#] to complete your entry if less than 6 digits. This access code will be entered into the pro-
gramming option [403].
5. Partition 1 Entry Delay 1, Partition 1 Exit Delay, enter each 3-digit delay time
Program the desired 3-digit Partition 1 Entry Delay (in seconds) followed by the desired 3-digit Partition 1 Exit Delay (in seconds). These
values will be entered in [005] > [01], entries 1 and 3, respectively.
6. Installer Code
Enter the required 4- or 6-digit access code installer access code (dependent on [701], entry 5). This Installer Access Code will be entered in
[006]. After the installer code has been programmed the keypad will return to the base installer programming menu.
All template programming information must be re-entered after performing a hardware or software panel default.

3.2 DLS Programming

3.2.1 Local Programming:
Follow the steps below in the sequence indicated to set up local programming using DLS:
1. Initiate downloading using the DLS software.
2. Connect an RS-232 to PC-Link Cable between the Computer with DLS Software installed and the alarm panel to be programmed.
Connecting the DLS PC to the panel will automatically initiate the connection.

3.2.2 Remote Programming (via telephone line):

Refer to Section [401] on page 22 for details.
The panel battery voltage can be monitored with DLS software. After the panel information has uploaded,
battery voltage can be viewed in the DLS session window.

3.3 Advanced Keypad Programming

DSC recommends filling in the Programming Worksheet with the required information before programming the system. This will reduce the
time required to program and will help eliminate errors.
To enter Installer Programming press [✱][8][Installer Code]. The Program light will flash (programmable LCD keypad displays will change
to ‘Enter Section’). An error tone indicates the installer code entered is incorrect. Press [#] to clear any key presses and try again.
The default Installer Code is [5555].

The Armed and Ready lights indicate programming status:

Armed Light On Panel waiting for 3-digit section number
If in module programming, waiting for section # to be entered
Ready Light On Panel waiting for data to be entered
Ready Light Flashing Panel waiting for HEX data to be entered

You cannot enter Installer Programming while the system or any partition is armed or in alarm.

9
PowerSeries - PC1616/PC1832/PC1864

. .1 Programming oggle ptions:

Enter the 3-digit programming section number:
• The Armed light will turn OFF and eypad ype ption ption FF
• The Ready light will turn ON.
L D one Lig t ON one Lig t OFF
• The keypad will display which toggle options are ON or OFF
according to the chart. Fixed-Message LCD Indicator ON Indicator OFF
• To toggle an option ON or OFF, press the corresponding num- Programmable-Message LCD Displayed Das -
ber on the keypad. The display will change accordingly. Displayed
• When all the toggle options are configured correctly, press the [#] key to exit the program section.
• The Ready light will turn OFF and the Armed light will turn ON.

. .2 Programming Decimal and exadecimal X Data:

• Enter the 3-digit programming section number.
• The Armed light will turn OFF and the Ready light will turn ON.
• Enter the data written in the boxes.
For sections that require multiple 2- or 3-digit numbers, the keypad will beep twice after each 2- or 3-digit entry and move to the next item in
the list. After the last digit in the section is entered, the keypad will beep rapidly 5 times and exit the program section. The Ready light will
turn OFF and the Armed light will turn ON.
For sections that do not require data for every box (such as phone numbers), press the [#] key to exit the program section after entering all the
required data. The Ready light will turn OFF and the Armed light will turn ON.
At any time the [#] key can be pressed to exit any program section. All changes made up to that point will be saved.
Value Enter Telephone Dialer
HEX (or hexadecimal) digits are sometimes required. To enter a HEX digit, press the
[✱] key to begin HEX programming. The Ready light will flash. X A Press ✱ 1 ✱ ot Supported
X B Press ✱ 2 ✱ Simulated ✱ key
Refer to the following chart and press the number corresponding to the HEX digit X C Press ✱ ✱ Simulated key
required. The Ready light will continue to flash. Press [✱] again to return to normal X D Press ✱ 4 ✱ Dial tone searc
decimal programming. The Ready light will turn ON. X Press ✱ 5 ✱ wo second pause
X F Press ✱ 6 ✱ nd o umber

In addition to the standard digits 0-9, HEX digits and special dialer functions can also be programmed.

. . ow to xit Installer Programming:

To exit installer programming, press the [#] key when the panel is waiting for a 3-digit section number (the Armed light is ON).

. .4 iewing Programming
LED and LCD5501Z Keypads
Any programming section can be viewed from an LED or LCD5501Z
keypad. When a programming section is entered, the keypad will immedi-
ately display the first digit of information programmed in that section.
The keypad displays the information using a binary format, according to
the following chart:
Press any of the Emergency keys (Fire, Auxiliary or Panic) to advance to
the next digit.

When all the digits in a section have been viewed, the panel will exit the section. The Ready light will turn OFF, and the Armed light
will turn ON. The system is now waiting for the next 3-digit programming section number to be entered. Press the [#] key to exit the
section.
LCD Keypad
The keypad will immediately display all the information programmed when a programming section is entered. Use the arrow keys (< >) to
scroll through the data being displayed. Scroll past the end of the data displayed or press the [#] key to exit the section.

10
 Chapter 4 Programming Descriptions

Chapter 4 Programming Descriptions

The following is a brief description of the features and options available in the Power PC1616/1832/1864 control panel. Please refer to the keypad
installation sheet for function key programming.

Global Stay Arming

If enabled by the installer, when this function key is pressed the panel will prompt the user for an access code. The panel will arm all partitions
assigned to that access code in Stay Mode when exit delay expires. If a partition was armed in Away mode when the Global Stay Arming key is
pressed, that partition will switch armed status to Stay when the delay expires. The Force arm attribute must be enabled on Entry/Exit points for
this feature.
Global Away Arming
If enabled by the installer, when this function key is pressed the panel will prompt the user for an access code. The panel will arm all partitions
assigned to that access code in Away Mode when exit delay expires. If a partition was armed in Stay mode when the Global Away Arming key is
pressed, that partition will switch armed status to Away when the delay expires. The Force arm attribute must be enabled on Entry/Exit points for this
feature.
Global Disarming
If enabled by the installer, when this function key is pressed the panel will prompt the user for an access code. The panel will then disarm all par-
titions assigned to that access code.
[001] to [004] Zone Definitions
Option Description
[00] Null Zone: Zone not used
[01] Delay 1: When armed, provides entry delay when violated (follows Entry Delay 1)
[02] Delay 2: When armed, provides entry delay when violated (follows Entry Delay 2)
[03] Instant: When armed, instant alarm when violated
[04] Interior: When armed, instant alarm will sound first if the zone is violated; instant alarm will follow the entry delay if entry delay is active
[05] Interior Stay/Away: Similar to ‘Interior’ except that panel will auto-bypass the zone if Armed in the Stay mode
[06] Delay Stay/Away: Similar to ‘Delay 1’ except that panel will auto-bypass the zone if Armed in the Stay mode
[07] Delayed 24-Hour Fire (Hardwire): Instant audible alarm when violated, communication is delayed 30 seconds. If alarm is acknowl-
edged during this time (by pressing a key), the alarm will be silenced 90 seconds and will repeat the cycle. If not, alarm will latch and
communicate after a 30-second delay
[08] Standard 24-Hour Fire (Hardwire): Instant alarm and communication when violated
[09] 24-Hr Supervision (Hardwire): Instant alarm and communication when violated. Will not sound the bell or keypad buzzer
[10] 24-Hr Supervisory Buzzer: Instant alarm, panel will activate keypad buzzer instead of bell output
[11] 24-Hr Burglary: Instant alarm when violated, audible alarm at default. Reporting code BA, BH
[12] 24-Hr Hold-up: Instant alarm when violated, silent alarm at default. Reporting code HA, HH
[13] 24-Hr Gas: Instant alarm when violated, audible alarm at default. Reporting code GA, GH
[14] 24-Hr Heat: Instant alarm when violated, audible alarm at default (also known as high-temp). Reporting code KA, KH
[15] 24-Hr Auxiliary (Medical): Instant alarm when violated, silent alarm at default. Reporting code MA, MH
[16] 24-Hr Panic: Instant alarm when violated, audible alarm at default. Reporting code PA, PH
[17] 24-Hr Emergency: Instant alarm when violated, audible alarm at default. Reporting code QA, QH
[18] 24-Hr Sprinkler: Instant alarm when violated, audible alarm at default. Reporting code SA, SH
[19] 24-hr Water: Instant alarm when violated, audible alarm at default (also known as high water level). Reporting code WA, WH
[20] 24-Hour Freeze: Instant alarm when violated, audible alarm at default (also known as low-temp). Reporting code ZA, ZH
[21] 24-Hr Latching Tamper: Instant alarm when violated, panel cannot be armed until Installer Programming is entered
[22] Momentary Keyswitch Arm: Arm or disarm the system when violated
[23] Maintained Keyswitch Arm: Arm system when violated, disarm system when restored
[24] For Future Use
[25] Interior/Delay: Zone will function as an Interior zone when armed in Away mode, and as a Delay zone when armed in Stay mode
[26] 24-Hr Non-Alarm: Zone will NOT create an alarm. Can be used with zone follower function for automation applications
[29] Auto-Verified Fire: When violated, system will reset all smoke detectors for 20 seconds, then wait 10 seconds for detectors to settle.
If another fire alarm is detected within 60 seconds, the zone will go into alarm immediately

11
PowerSeries - PC1616/PC1832/PC1864

[30] Fire Supervisory: Instant alarm, system will activate keypad buzzer. A valid user code is required to silence keypad buzzer
[31] Day Zone: Instant alarm when system is armed, keypad buzzer (no alarm) when system is disarmed
[32] Instant Stay/Away: Similar to ‘Instant’ except panel will auto-bypass the zone if Armed in the Stay mode
[35] 24-Hr Bell/Buzzer: Instant alarm when violated, system will activate bell output if armed, keypad buzzer if disarmed
[36] 24-Hr Non-Latching Tamper Zone: Instant tamper condition when violated. Active in both the armed and disarmed state
[37] Night Zone: Functions like Interior Stay/Away but will remain bypassed if the user presses [✱][1] to re-activate Stay/Away zones
when armed in the Stay mode
[41] 24 Hr. Carbon Monoxide: This zone type is used with a hardwired CO detector. This zone definition has a distinct bell cadence in the
event of an alarm. The cadence of this alarm is 4 cycles of 100ms on/off pulses, followed by a 5-second pause, and then repeated.
After 4 minutes, the 5-second pause is extended to 60 seconds in duration. The bell is silenced when an access code is entered or the
bell times out (see your Carbon Monoxide instruction sheet for more details).
[81] 24 Hr. Carbon Monoxide (Wireless): This zone type is used with a wireless CO detector. This zone definition has a distinct bell
cadence in the event of an alarm. The cadence of this alarm is 4 cycles of 100ms on/off pulses, followed by a 5-second pause, and then
repeated. After 4 minutes, the 5-second pause is extended to 60 seconds in duration. The bell is silenced when an access code is
entered or the bell times out.
[87] Delayed 24-Hour Fire (Wireless/Addressable): Same as Delayed 24-Hour Fire (Hardwire) but must be used for wireless or address-
able smoke detectors
[88] Standard 24-Hour Fire (Wireless/Addressable): Same as Standard 24-Hour Fire (Hardwire) but must be used for wireless or
addressable smoke detectors

[005] System Times

After entering Section [005], enter the 2-digit subsection number for the desired partition and program the Entry Delay 1, Entry Delay 2 and Exit
Delay for each active partition on the system. Valid entries are from [001] to [255] or [045] to [255] for SIA CP-01 panels (in seconds). Enter
subsection [09] to program the Bell Cut-Off Time. Valid entries are from [001] to [255] (in minutes).

[006] Installer Code

The default Installer Code is [5555] or [555555] if 6-Digit Access Codes is enabled.

[007] Master Code

The default Master Code is [1234] or [123456] if 6-digit Access Codes is enabled.

[008] Maintenance Code

The default Maintenance Code is [AAAA] (not programmed). This code can arm any partition, but cannot disarm unless the partition is in alarm.

[009] to [011] PGM Outputs

The PC1616 and PC1832 have two on-board PGM outputs (PGM1 and PGM2). The PC1864 has four on-board PGM outputs (PGM1 to
PGM4). The panel has the capacity for up to 14 PGM outputs (8 additional low-current PGM outputs with PC5208 module, 4 additional
high-current PGM outputs with a PC5204 module).

PGM Output Options:

Option Description
[00] For Future Use
[01] Fire and Burglary: Output will activate (steady for burglary, pulsing for fire) if an alarm occurs on the selected partition
[02] For Future Use
[03] Sensor Reset: Output will normally be active and deactivate for 5 seconds when a [✱][7][2] fire reset command is entered or when
an Auto-Verify Fire alarm is detected
[04] 2-Wire Smoke: Configures PGM2 as 2-wire smoke detector input (PGM2 only)
[05] Armed Status: Output will activate when all of the selected partitions are armed
[06] Ready Status: Output will activate when all the selected partitions are in the Ready state (Ready light ON)
[07] Keypad Buzzer Follow: Output will activate and follow the keypad buzzer for the selected partition when the following events
occur: entry delay, door chime, audible exit delay, automatic arming pre-alert, 24-hr Supervisory Buzzer zone alarm
[08] Courtesy Pulse: Output will activate during entry/exit delay if the selected partition is armed, and will remain active for an addi-
tional 2 minutes after the entry or exit delay expires
[09] System Trouble: Output will activate when any selected trouble condition is present
[10] Latched System Event (Strobe): Output will activate when a selected condition occurs on any selected partition. Note output can
be programmed to follow timer

12
 Chapter 4 Programming Descriptions

[11] System Tamper: Output will activate when any tamper condition is present
[12] TLM and Alarm: Output will activate if a telephone line trouble is present and then an alarm occurs
[13] Kissoff: Output will activate for 2 seconds when a valid kissoff is received from the central station
[14] Ground Start: Output will activate for 2 seconds when the panel attempts to seize the phone line (additional dial tone search must
be programmed in the central station phone number – HEX [D])
[15] Remote Operation: Output can be activated/deactivated via the DLS software
[16] For Future Use
[17] Away Armed Status: Activates when all of the selected partitions are armed in Away mode
[18] Stay Armed Status: Activates when all of the selected partitions are armed in Stay mode
[19] Command Output 1: Activates when a [✱][7][1] command is entered on the selected partition – Command can be programmed to require
a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[20] Command Output 2: Activates when a [✱][7][2] command is entered on the selected partition – Command can be programmed to require
a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[21] Command Output 3: Activates when a [✱][7][3] command is entered on the selected partition – Command can be programmed to require
a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[22] Command Output 4: Activates when a [✱][7][4] command is entered on the selected partition – Command can be programmed to require
a valid access code and output can be programmed to activate for the time programmed in Section [170] or programmed to latch.
[23] Silent 24-Hour Input: Changes PGM to a 24-hr Silent zone (PGM2 only)
[24] Audible 24-Hour Input: Changes PGM to a 24-hr Audible zone (PGM2 only)
[25] Delayed Fire and Burglary: Functions as a Fire and Burglary output but does not activate until the TX Delay time expires
[26] Battery Test Output: Output activates for 10 seconds at midnight each day.
[27] For Future Use
[28] Holdup Output: Activates when a Holdup Alarm occurs on any assigned partition. Remains active until all assigned partitions have
been armed or disarmed. Will not activate if a Holdup Zone goes into a fault or tamper condition.
[29] Zone Follower (Zones 1-8): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[30] Partition Status Alarm Memory: Activates if the selected partition is armed. Output will pulse “one second ON / one second OFF
if an alarm occurs
[31] Alternate Communicator: Activates when selected system event occurs. If active in the armed state, it remains active until the sys-
tem is disarmed. If activated in the disarmed state, it remains active until a valid access code is entered within the bell cut-off time, or
when the system is armed after the bell cut-off time has expired.
[32] For Future Use
[33] For Future Use
[34] Away Armed with no Zone Bypassed Status: Activates when armed with stay/away zones active and no zones bypassed.
[35] Zone Follower (Zones 9-16): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[36] Zone Follower (Zones 17-24): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[37] Zone Follower (Zones 25-32): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[38] Zone Follower (Zones 33-40): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[39] Zone Follower (Zones 41-48): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[40] Zone Follower (Zones 49-56): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
[41] Zone Follower (Zones 57-64): Active when any of the selected zones are active and deactivates when all of the selected zones are restored.
* See Section [501]-[514] Programmable Output Attributes, PGM Output Option [29] and [35]-[41] Option 8 on 24.

[012] Keypad Lockout

The system can be programmed to ‘lockout’ keypads if a series of incorrect user or installer codes are entered. When lockout is active, all
keypads emit a steady 2-second error tone when a key is pressed. Program the Number of Invalid Codes Before Lockout with the desired
number. Valid entries are from [000] to [255]. Program data [000] to disable the feature. Keypads will remain locked out for the number of
minutes programmed for the Lockout Duration. Valid entries are from [000] to [255].

13
PowerSeries - PC1616/PC1832/PC1864

[013] First System Option Code

Option Description
[1] ON: zones require normally-closed loops. OFF: zones require End-Of-Line resistors, as determined by option [2].
[2] ON: zones require double End-Of-Line resistors. OFF: zones require single End-Of-Line resistors.
[3] ON: keypads will display all trouble conditions while armed. OFF: keypads will only display fire trouble when armed. This option
must be OFF if LCD5500 v2.x (or older) keypads are used on the system.
[4] ON: only a trouble will be displayed. OFF: keypads will display a trouble and a zone violation if a tamper or fault is detected.
[5] ON: auto-arming schedules (Program Sections [181]-[188]) will be available to the user in the [✱][6] menu.
OFF: auto-arming schedules will not be available to the user in the [✱][6] menu.
[6] ON: the Audible Exit Fault feature will be enabled. If a delay zone is not secured correctly and not force-armed at the end of the exit
delay, the system will go into entry delay and turn ON the bell output. The bell will also sound if the delay zone is opened within 10
seconds of the exit delay timeout.
OFF: the keypad will sound the entry delay through the keypad as per usual.
[7] ON: the system will NOT log additional alarms for a zone that has reached the swinger shutdown threshold.
OFF: all zone alarms will be logged.
[8] ON: Temporal Three Fire Signal is used to sound fire alarms (½ second ON, ½ second OFF, ½ second ON, ½ second OFF ½ second
ON, 1 ½ seconds OFF).
OFF: the system will pulse the bell output (½ second ON, ½ second OFF).

[014] Second System Option Code

Option Description
[1] ON: the system squawks the bell output once when a partition is armed, twice when disarmed.
OFF: the bell output does not activate. Refer to section [017] option 8.
[2] ON: the system squawks the bell output every 10 seconds during the auto-arm pre-alert.
OFF: the bell output does not activate.
[3] ON: the system will squawk the bell output once every second during Exit Delay, 3 squawks per second for the last 10s.
OFF: the bell output will not activate.
[4] ON: the system will squawk the bell output once every second during Entry Delay, 3 squawks per second for the last 10s.
OFF: the bell output will not activate.
[5] ON: the system squawks the bell output once every 10 seconds when a trouble condition is present.
OFF: the bell output does not activate.
[6] ON: the system will beep the keypads once every second, and 3 times a second over the last 10 seconds, during an exit delay when
the system is armed with a user code or armed in the Away mode.
OFF: the keypads will not beep.
[7] ON: the exit delay will be terminated (reduced to 5 seconds) when a Delay 1 zone is violated and restored after the system is armed.
OFF: the exit delay will count down as normal.
[8] ON: the bell output will not timeout if a fire alarm occurs. The user must turn OFF the bell by entering a valid user code.
OFF: the bell output will timeout normally.

[015] Third System Option Code

Option Description
[1] ON: the keypad fire emergency key will be enabled. OFF: the keypad fire emergency key will be disabled.
[2] ON: the keypad Panic emergency will be audible (bell output). OFF: the Panic emergency key will be silent.
[3] ON: the Quick Exit feature will be enabled. OFF: the Quick Exit feature will be disabled.
[4] ON: the Quick Arming [✱][0] feature will be enabled. OFF: Quick Arming [✱][0] feature will be disabled.
If this feature is disabled, a valid user code must be entered after the Stay or Away function buttons are pressed.
[5] ON: a valid user code must be entered after pressing [✱][1] to access the Bypass feature. OFF: user code is not required.
[6] ON: the Master Code (user code 40) can only be changed in Installer Programming.
OFF: the Master Code can be changed using the User Programming [✱][5] command.
[7] ON: the system supervises the telephone line and displays a trouble if disconnected.
OFF: the telephone line is not supervised.
[8] ON: the system activates the bell output if a telephone line trouble is detected while the system is armed.
OFF: the system activates the keypad buzzer trouble tone.

14
 Chapter 4 Programming Descriptions

[016] Fourth System Option Code

Option Description
[1] ON: the system supervises the AC input and displays a trouble if a failure is detected. OFF: AC Input is not supervised.
[2] ON: the trouble light will flash when an AC trouble is detected. OFF: the trouble light turns on, does not flash.
[3] ON: the keypad blanks (no indicator lights) if a key is not pressed for 30 seconds. OFF: the keypad does not blank.
ON: a valid user code must be entered to restore normal keypad operation after the blanking.
[4]
OFF: pressing any key will return the keypad to normal operation.
[5] ON: keypad backlighting enabled. OFF: keypad backlighting disabled.
ON: the system temporarily enables the Keypad Blanking feature if an AC failure is detected (to preserve the back-up battery).
[6]
OFF: the system will operate as normal.
ON: the keypad turns ON the Bypass light if zones are bypassed while the system is armed.
[7]
OFF: the Bypass light turns OFF when the system is armed.
[8] ON: the system supervises keypad tampers. OFF: the system does not supervise keypad tampers.

[017] Fifth System Option Code

Option Description
[1] ON: the system does NOT associate wireless keys to user codes.
OFF: the system will assign user code 17 to wireless key #01, user code 18 to wireless key #02 etc. If the wireless key is used to arm
or disarm, the system will report the Opening or Closing for the associated User Code.
[2] ON: the system logs an RF Jam trouble condition if the condition is present for 5 minutes.
OFF: the system logs the trouble condition after 30 seconds.
[3] ON: the keypads beep if an RF Jam trouble is detected.
OFF: the trouble is not announced via the keypad buzzer.
[4] ON: the Double Hit feature will be enabled. Two violations from the same zone within the Cross Zone Timer will be considered a
valid Police Code or Cross Zone event. The system will report the event and log it to the event buffer.
OFF: two alarms from the same zone is not a valid Police Code or Cross Zone event.
[5] ON: the system logs and communicates a Late-To-Close event when the auto-arm time comes, but the function has been disabled
(not if auto-arming was caused by the No-Activity Arming feature).
OFF: the system does not transmit or log a Late-To-Close event.
[6] ON: enables the Daylight Savings automatic clock adjustment feature.
OFF: the system does not automatically adjust the clock for Daylight Savings.
[7] For Future Use
[8] ON: the system only squawks the bell output when the system is armed in the Away mode.
OFF: the system squawks the siren when the system is armed in any mode. (See Section [14], Option [1]).

[018] Sixth System Option Code

Option Description
[1] ON: the system only transmits a Test Transmission reporting code if no other event was transmitted to the central station during the
programmed time.
OFF: the system always transmits a Test Transmission reporting code as programmed.
[2]-[4] For Future Use
[5] ON: the keypad buzzer follows the bell output for all alarms.
OFF: the system only activates the bell output for all alarms.
[6] ON: When an alarm is detected on a zone (with the Cross Zone attribute enabled), a timer is started. The alarm is not transmitted and
the bell output is not activated unless a second cross zone enabled zone is violated before the Cross Zone timer times out.
OFF: the system reports all alarms normally and logs and transmits a Police Code reporting code if a second zone alarm is detected
during the armed period.
[7] ON: The system restarts the Exit Delay (one time) if a Delay zone is violated and restored during the exit delay time.
OFF: The Exit Delay does not restart.
[8] ON: The system activates the trouble beeps when an AC trouble is detected.
OFF: the system does not announce AC troubles using the keypad buzzer.

15
PowerSeries - PC1616/PC1832/PC1864

[019] Seventh System Option Code

Option Description
[1] For Future Use
[2] For Future Use
[3] ON: When disarming, the keypad will display only the first alarm to occur during the last arming period.
OFF: When disarming, the keypad will display all zones that were in alarm during the last arming period
[4]-[5] For Future Use
[6] ON: the green LED indicator on the keypads indicate the status of AC on the system
OFF: the green LED indicator on the keypads indicate the partition ready status
[7] ON: All user access codes can enter the User Functions menu.
OFF: Only the Master Code can enter the User Functions menu.
[8] For Future Use

[020] Keypad Zone Assignment

Enter the two-digit zone number to be assigned to each keypad assigned to a specific slot. Only one keypad can be assigned to a specific slot.
See Keypad Assignment. Valid entries are from [00] to [64].

[021] Eighth System Option Code

Option Description
[1] ON: Access codes will not be accepted by the system during entry delay.
OFF: An access code can be used to disarm the system during entry delay
[2]-[5] For Future Use
[6] ON: Key-switches and wireless keys can only disarm the system during an entry delay
OFF: Key-switches and wireless keys can disarm the system regardless if entry delay is active or not.
[7]-[8] For Future Use

[022] Ninth System Option Code

Option Description
[1] ON: An access code is required for access to the [✱][1], [✱][2], [✱][3] menus.
OFF: No access code is required for [✱][1], [✱][2], [✱][3] menu access.
[2]-[3] For Future Use
[4] ON: Only the Master code can be used to bypass a hold up zone.
OFF: Any valid access code can bypass a hold up zone.
[5] For Future Use
[6] ON: RF Delinquency Enabled, if any wireless zone supervisory transmission is not received by the PC5132 during a 15-minute period,
the PC5132 will place the panel into Not Ready To Arm mode. In the armed state, the Zone faults will generate tamper alarms. The panel
will generate a silent trouble (NO trouble beeps but the Trouble LED is turned ON) called “RF Device Delinquency”, which is only
viewable in [✱][2] (Trouble Menu). The user can override the condition and arm the panel by using the feature.
OFF: RF Delinquency Disabled, the system will not indicate an RF Delinquency when a zone supervisory transmission is not
received during a 15 minute period.
[7] Future Use
[8] ON: When the system is armed in Stay mode, during the Exit delay, the system will sound one beep every 3 seconds.
OFF: When the system is armed in Stay mode, the system will be silent during the Exit delay.

[023] Tenth System Option Code

Option Description
[1] ON: the keypad [F] emergency key will only beep three times to acknowledge that the button has been pressed. The system will not
activate the bell output. OFF: the system will activate the bell output and beep the keypad.
[2] For Future Use
[3] ON: the system will only transmit the Test Transmission reporting code if the system is armed at the time the system is programmed
to report the event. OFF: the system will always report the Test Transmission reporting code at the programmed time.
[4] ON: the system changes the Test Transmission Reporting Cycle Time from Days to Hours.
OFF: the Test Transmission Reporting Cycle Time is in Days.

16
 Chapter 4 Programming Descriptions

[5] ON: the user cannot switch from Away Arm mode to Stay Arm mode using the function keys.
OFF: the user can switch arming modes.
[6] ON: the system disconnects a listen in/two-way session if a new event occurs.
OFF: the system does NOT disconnect. New events are transmitted only after the session is terminated.
[7] ON: the system does NOT activate the keypad buzzer for any trouble condition (excluding Fire Troubles).
OFF: the system announces troubles via the keypad buzzer (two beeps every 10 seconds).
[8] ON: Keyswitches will always arm in Away mode.
OFF: Keyswitches will arm in Away mode if an entry/exit zone is violated during exit delay.

[030] Fast Loop Response

This section is used to determine the Loop Response Time for the main panel zones.
ON: the loop response time will be 36 ms. OFF: the loop response time will be 400 ms.

[101] to [164] Zone Attributes

These sections are used to customize the operation of the zones. There are 9 toggle options in each section:
Option Description
[1] ON: alarms are audible (bell output).
OFF: alarms are silent.
[2] ON: the bell output is steady (burglary).
OFF: the alarm output pulses (fire).
[3] ON: a zone violation or restoral will activate Chime.
OFF: Chime is not activated.
[4] ON: the user can manually bypass the zone using the [✱][1] command.
OFF: the zone cannot be manually bypassed.
[5] ON: the partition can be armed even if the zone is violated (the zone will not affect the Ready status).
OFF: the zone must be secure before arming.
[6] ON: the system shuts down alarm reporting after the programmed number of alarms have occurred.
OFF: the panel will always report the event if an alarm occurs.
[7] ON: the system delays reporting the event for the time programmed for the Transmission Delay time.
OFF: the panel immediately transmits the reporting event when an alarm is detected.
[8] ON: the zone is a wireless or addressable device.
OFF: the zone is a hardwire zone (main panel, zone expander or keypad zone).
[9] ON: the zone has the Cross Zone feature enabled.
OFF: the zone functions normally.
[10]-[13] For Future Use
[14] ON: the zone requires a normally-closed loop
OFF: the zone will follow the EOL configuration in [013]
[15] ON: the zone requires a single End-of-Line resistor
OFF: the zone will follow the EOL configuration in [013]
[16] ON: the zone requires double End-of-Line resistors
OFF: the zone will follow the EOL configuration in [013]
Options [14], [15], [16] apply to first 8 zones only. If more than one of these options are enabled then lowest numbered option is enabled. E.g.,
If Option [14] and option [15] are enabled then the zones are configured as normally closed loops.

Keypad zones and zone expanders will always follow [013].

When Zone Types ([001] to [004]) are programmed, the system will change the Zone Attributes to those found in the chart included in the
Programming Worksheets. The Zone Attributes will default if a new Zone Type is programmed for a specific zone. After programming the Zone
Types, enter [101] to [164] and ensure that all options are programmed correctly.
Ready light ON: Program attributes [1-8] (press [1]-[8] to turn option ON or OFF)
Ready light and Armed light ON: Program attributes [9-16] (press [1]-[8] to turn option ON or OFF)
Press [9] to switch between attributes [1-8] and attribute [9-16].

[165] Maximum Dialing Attempts

Program the Maximum Dialing Attempts before the panel will generate a Failure to Communicate (FTC) trouble condition.
Valid entries are [001] to [005]. For UL Listed installations, 5 attempts is required.

17
PowerSeries - PC1616/PC1832/PC1864

166 Post Dial Wait or ands ake

Program the maximum time the panel will wait, after dialing, for a valid handshake from the central station.
Valid entries are [001] to [255] seconds.

167 L GS Module Wait or Acknowledgement

Program the maximum time the panel will wait, after sending a data packet, for an acknowledgement from the central station.
Valid entries are [060] to [255] seconds.
Do not program this section with a value less than 60.

16 Daylig t Sa ing ime Mo e Clock A ead

This option is used to program the Date, Time and Increment that the clock will move ahead for Daylight Savings Time each year. Program-
ming can be accomplished by programming the Month, Day, Hour and Increment or Month, Week, Day of Week, Hour and Increment:
Month: Data [001] to [012] represents January to December.
Week: Data [000] indicates that the day of the month will be programmed in the Day section below. Data [001] to [005] represents weeks 1
to 5 of the month. Week 5 always represents the last week in the month, regardless if the number of weeks in the month is 4 or 5.
Day: Data [001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005] was
programmed in the Week Section above, then Data [000] to [006] represents Sunday to Saturday
Hour: Data [000] to [022] represents the hour that Daylight Saving Time will take effect.
Increment: Data [001] to [002] represents the number of hours to advance the clock for Daylight Savings Time.

Do not program the Hour outside of the valid range or the time will not change. Do not program the value of the Increment to be greater
then the number of hours remaining in the current day.

16 Standard ime Set Clock Back

This option is used to program the Date, Time, and Increment that the clock will move back for Standard Time each year. Programming can
be accomplished by programming the Month, Day, Hour, and Increment or Month, Week, Day of Week, Hour, and Increment:
Month: Data [001] to [012] represents January to December.
Week: Data [000] indicates that the day of the month will be programmed in the Day section below. Data [001] to [005] represents weeks 1
to 5 of the month. Week 5 always represents the last week in the month, regardless if the number of weeks in the month is 4 or 5.
Day: Data [001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005] was
programmed in the Week section above, then Data [000] to [006] represents Sunday to Saturday.
Hour: Data [000] or [023] represents the hour that Standard Time will take effect.
Increment: Data [001] or [002] represents the number of hours to roll back the clock for Daylight Saving Time.

170 PGM utput imer

Program the amount of time, in seconds, that the PGM Output Timer will be active. Valid entries are [001] to [255].

171 amper PGM utput imer

Program the amount of time, in minutes, that a tamper condition will latch the Tamper PGM output. Valid entries are [000] to [255].

175 Auto-arm Postpone imer

Program the amount of time, in minutes, that the system will postpone automatic arming. When the programmed time has expired, the system will
attempt to auto-arm again. If data [000] is programmed, the system will instead abort the auto-arm sequence. Valid entries are [001] to [255].

176 Cross one Police Code imer

Program the amount of time in seconds (Cross Zone), or minutes (Police Code), that the panel will use to determine if a Cross Zone or Police
Code event has occurred. If data [000] is programmed when using the Police Code feature, and if any two zones go into alarm during any armed-
to-armed period, the panel will generate a Police Code event. Valid entries are [001] to [255].

1 1 to 1 Auto-arm Sc edules
Program the amount of time to auto-arm ([181] for partition 1, [182] for partition 2, etc.) for each day of the week. Each option has seven, 4-digit
entries: two digits for the hour, two digits for the minute, Sunday through Saturday. Program using the twenty-four-hour system (for example, to
auto-arm at 8:00 pm, program data [20][00]). Valid entries are [00][00] to [23][59]. Program [99][99] to disable auto-arming.

1 0 o Acti ity Arming Pre-Alert Duration

Program the amount of time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypads will emit a steady tone, warning the user
that the system is about to arm. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255].

1
 C apter 4 Programming Descriptions

1 1 to 1 o Acti ity Arm imer

Program the amount of time, in minutes, for the No Activity Arm Timer ([191] for Partition 1, [192] for Partition 2, etc.). If Delay Zones are
restored and no zone activity is detected for the time programmed, the system will start the auto-arm sequence. Valid entries are [000]-[255].

1 Auto-Arming Pre-alert imer

Program the amount of time, in minutes, for the Auto-Arming Pre-Alert Time. This timer is used for all programmed auto-arming features (is not
used for No Activity Arming). The keypads will provide a steady tone, warning the user that the system will arm. The user can enter a valid
access code to abort the arming sequence. Valid entries are [001] to [255].

201 Partition Selection Mask

Turn the corresponding option ON to enable partitions [1] to [8]. ON (bit 1 cannot be turned OFF).

202 to 265 Partition one Assignments

These options are used to assign zones to specific partitions ([202] to [209] for Partition 1, [210] to [217] for Partition 2, etc.). Turn ON the
option corresponding to the partition and zone to enable the zone on the specified partition. Turn the option OFF to disable the zone on the
specified partition. Zones assigned to more than one partition are called ‘common zones’ and will be armed only if all the partitions the zone
is assigned to are armed. Default = Zones 1-8 enabled on Partition 1.

01 First elep one umbers

The information in this section also applies to sections [302] and [303]. Telephone number 3 is dedicated as a back-up to Telephone number
1. These sections determine which type of communicator is activated in the event of an alarm (telephone, GPRS and Ethernet) and the
sequence that the system follows in the event of an unsuccessful communication.
• Entry of [D] followed by a [Telephone Number] terminated with “F” configures the section for telephone dialing.
E.g.: [D12223334444F]
• Entry of [D] followed by [CAA] terminated with “F” allows the system configuration to be determined by the GPRS/Ethernet module.
E.g.: [DCAAF]
• Enter [DCBBF] to configure the section for Ethernet Receiver 1
• Enter [DCCCF] to configure the section for Ethernet Receiver 2
• Enter [DCDDF] to configure the section for GPRS Receiver 1
• Enter [DCEEF] to configure the section for GPRS Receiver 2
Please refer to Section [350] Communicator Formats, only SIA and Contact ID are valid alternate communicator formats.
Programming any other format will send SIA by default.

Please refer to your associated communicator manual for more details.

Telephone Communications
All telephone number sections are 32 digits in length. Hexadecimal digits may be programmed in the telephone number to perform addi-
tional functions as follows:
Enter [✱][2][✱] – HEX B to dial “✱”
• Enter [✱][3][✱] – HEX C to dial “#”
• Enter [✱][4][✱] – HEX D for an additional dial tone search, as is required for PBX telephone systems
• Enter [✱][5][✱] – HEX E to insert a 2-second pause in the telephone number.

There is an automatic 2-second pause before additional dial tone searches are initiated.

• HEX A is not used.

• HEX F represents the end of the phone number (everything after F is ignored).
• Pressing [#] in these sections will exit and save the entire phone number.
• The panel will not attempt to communicate, if no phone number is programmed. This applies to phone numbers 1 and 2.

02 Second elep one umber

See [301] First Telephone Number for details.

0 ird elep one umber

See [301] First Telephone Number for details.

04 Call Waiting Cancel String

Program the digits required to disable call waiting. If enabled, the system will dial the programmed string on the first dialing attempt.
Program unused digits with data [F].

1
PowerSeries - PC1616/PC1832/PC1864

[310] System Account Number

Program the System Account Number. Only the SIA format supports 6-digit account numbers. If a 4-digit account number is required,
program the last two digits as data [FF]. When using the SIA format, this account number will be used for all reporting events. When using a
different format, this account number will be used for all events that are not partition-specific (for example, low battery, AC trouble, etc.).
For partition-specific events the system will use the programmed Partition Account Number. For all formats other than SIA, program a HEX
[A] for any digit [0] in the account number being used.

[311] to [318] Partition Account Numbers

Program the Partition Account Number for each active partition ([311] for partition 1, [312] for partition 2, etc.). When using the Automatic
SIA format, these account numbers are not used. The system will use the System Account Number for all reporting events. For all formats
other than SIA, program a HEX [A] for any digit [0] in the account number being used.

[320] to [349] Reporting Codes

Program the reporting code for all events to be transmitted. For a description of when each reporting event will be transmitted, refer to
Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable
the reporting of an event. If any other data is programmed (Data [01] to [FF]), the panel will automatically generate the correct reporting
event when transmitting to the central station. For all formats excluding Automatic SIA and Automatic Contact ID, the panel will not attempt
to report an event if data [00] or data [FF] is programmed for the reporting code.

[350] Communicator Format

Program the 2-digit number for the desired Communicator Format for the First Phone Number and the Second Phone Number. When dialing
the Third Phone Number, the system will use the Communicator Format programmed for Phone Number 1. Refer to the Programming Work-
sheet for a list of the available Communicator Formats. See Appendix F for details.

[351] to [376] Communicator Call Direction Options

Reporting events are categorized into 5 groups: Alarm/Restore, Opening/Closing, Tamper Alarm/Restore, System Maintenance, and Test
Transmissions. Program which Phone Number the control panel will use to transmit reporting events by turning the option ON in the correct
section. Phone Number 1 and/or Phone Number 2 can be used.

[377] Communicator Variables

Program a 3-digit number for each program entry:
Swinger Shutdown (Alarms): Maximum number of alarm/restoral transmissions per zone. Valid entries: [001] to [014]. Program data [000] to
disable shutdown.
Swinger Shutdown (Tamper): Maximum number of tamper alarm/restoral transmissions per zone. Valid entries: [000] to [014]. Program data
[000] to disable shutdown.
Swinger Shutdown (Trouble): Maximum number of trouble alarm/restoral transmissions per trouble condition. Valid entries: [000] to [014].
Program data [000] to disable shutdown.
Communicator (Transmission) Delay: Time, in seconds, the panel will delay reporting an alarm event. Valid entries: [000] to [255].
AC Failure Communication Delay: Time, in minutes, the panel will delay reporting an AC trouble event. Valid entries: [000] to [255].
TLM Trouble Delay: Time, in 3-second intervals, before the system will consider the phone line disconnected. Valid entries: [003] to [255]
(e.g., 3 x10 seconds = 30 seconds).

TLM Restoral follows the same delay.

Test Transmission Cycle (Land Line): Number of days between test transmission reporting events. Valid entries: [001] to [255].
Wireless Zone Low Battery Delay: Number of days the system will delay reporting a wireless low battery to the central station.
Valid entries: [000] to [255]. Program data [000] for no delay.
Delinquency Transmission Delay: Number of hours (Activity Delinquency) or days (Arming Delinquency) the panel will delay before transmit-
ting the event to the central station. Valid entries: [001] to [255].
Communication Cancel Window: Time, in minutes, after an alarm has occurred that the system will report a Communication Cancel reporting
event if the system is disarmed. They keypad will beep rapidly to indicate that the Communication Cancel reporting event has been communi-
cated successfully. Valid entries: [001] to [255]. Entering [000] will disable this window.

[378] Test Transmission Time

Program the time the system will report a Test Transmission reporting event. Program 4 digits – [HH][MM] using the twenty-four-hour sys-
tem. For a test transmission at 11:00 pm, program data [23][00]). Valid entries are [00][00] to [23][59]. Entering [99][99] will disable the test
transmission.

[379] Periodic DLS Time of Day

Programs the time the system will auto-call DLS. Program 4 digits – [HH][MM] using the twenty-four-hour system. For a DLS auto-call at
11:00 pm, program data [23][00]). Valid entries are [00][00] to [23][59]. Programming [99][99] will select a random time, [FF][FF] will dis-
able it.

20
 Chapter 4 Programming Descriptions

[380] First Communicator Option Code

Option Description
[1] ON: the system communicator is enabled.
OFF: the communicator is disabled.
[2] ON: the system transmits alarm restorals if the zone is restored and the bell has timed out.
OFF: the system transmits alarm restorals immediately when the zone is restored.
[3] ON: the panel uses rotary (pulse) dialing. OFF: the panel uses DTMF (touchtone) dialing.
[4] ON: the panel will switch from DTMF dialing to rotary dialing after the 4th failed attempt to communicate.
OFF: the panel will use DTMF dialing for all dialing attempts.
[5] ON: the system uses the Third Phone Number to back up the First Phone Number.
OFF: the Third Phone Number is disabled.
[6] ON: the system alternates between the First Phone Number and Third Phone Number when attempting to report an event.
OFF: the panel will dial the First Phone Number for the programmed number of attempts, then switch to the Third Phone Number.
[7] For Future Use
[8] ON: the Delinquency feature follows zone activity. OFF: the Delinquency feature follows arming.

[381] Second Communicator Option Code

Option Description
[1] ON: the keypad beeps 8 times after successfully transmitting the Opening After Alarm reporting event.
OFF: the keypad does not beep.
[2] ON: the bell output squawks 8 times after successfully transmitting the Opening After Alarm reporting event.
OFF: the bell output does not activate.
[3] ON: the system uses programmed reporting codes when transmitting using the SIA format.
OFF: the system automatically generates all reporting codes transmitted.
[4] ON: the system beeps the keypad 8 times after successfully transmitting a Closing reporting event.
OFF: the keypad does not beep.
[5] ON: the system requests a Listen in/two-way session the next time it calls the 1st/3rd Phone Number when the PC59xx transmits a request.
OFF: the system ignores the request from the PC59xx.

This option is used with PC59xx series modules.

[6] ON: the system requests a Listen in/Two-way session the next time it calls the 2nd Phone Number when the PC59xx transmits a request.
OFF: the system will ignore the request from the PC59xx.

This option is used with PC59xx series modules.

[7] ON: the system uses Contact ID format programmed reporting codes when transmitting reporting codes.
OFF: the system automatically generates all reporting codes transmitted.
[8] ON: the system will follow ULC Communication Priority.
OFF: the system will follow standard communications priority.

[382] Third Communicator Option Code

Option Description
[1] For Future Use
[2] ON: the system will transmit all alarms during Walk Test. OFF: the system will not report alarm events during Walk Test.
[3] ON: the keypad will display the message ‘Communications Cancelled’ (programmable LCD) or ‘CC’ (fixed-message LCD) upon
successful transmission of the Communication Cancelled reporting event.
OFF: the keypad will not display these messages.
[4] ON: the system dials the Call Waiting Cancel String on the first attempt to dial the central station.
OFF: the system does not dial the Call Waiting Cancel String.
[5] ON: enables support for the TL/GS Module. OFF: disables TL/GS Module.
[6] ON: the AC Failure Transmission Delay Timer is in hours. OFF: the delay is in minutes.
[7] ON: sets the number of Dialing attempts to 1 when using Residential Dial Format.
OFF: residential Dial follows Dialing Attempt Counter.
[8] For Future Use

21
PowerSeries - PC1616/PC1832/PC1864

[383] Fourth Communicator Option Code

Option Description
[1] ON: events programmed to communicate to phone #1 will use the Partition Account Number in [311]. Events Programmed to com-
municate to phone #2 will use the Partition Account Number in [312].
OFF: each event will use its respective partition account code.
[2]-[8] For Future Use

[389] TL/GS Module Fault Check Timer

Program the time, in 3-second intervals, before the system considers the TL/GS Module disconnected. Valid entries: [002] to [255]
(e.g., 010 x 3 seconds = 30 seconds).

[401] First Downloading Option Code

Option Description
[1] ON: the system answers incoming calls for downloading (either Programmed Number of Rings or Double Call).
OFF: the system does not answer incoming calls using the double call routine for downloading.

These settings do not affect the 6-hour DLS downloading window on power-up.
[2] ON: the user can enable downloading for the DLS Window using the [✱][6] command.
OFF: the user cannot enable downloading.
[3] ON: the system will hang up after a successful DLS connection and call the computer back using the DLS Phone Number ([402]).
OFF: the system stays connected to the computer.
[4] ON: the user can initiate a downloading session using the [✱][6] command.
OFF: the user cannot initiate a downloading session.
[5] ON: the system attempts to call the downloading computer after transmitting an Event Buffer 75% Full event to the central station.
OFF: the system does NOT call the downloading computer after transmitting this event.
[6] ON: panel communicates with DLS at 300 Baud. OFF: panel communicates with DLS at 110 Baud.
[7]-[8] For Future Use

[402] Downloading Computer Phone Number

The Downloading Computer Telephone Number is used for Call Back, User Initiated DLS, and the Auto Event Buffer Upload functions.
Program the phone number as required. HEX digits can be included for special applications:
HEX [A] Not used
HEX [B] Simulates a [✱] key press
HEX [C] Simulates a [#] key press
HEX [D] Additional dial tone search
HEX [E] 2-second pause
HEX [F] End of phone number marker

[403] Downloading Access Code

Program the 6-digit Downloading Access Code. Upon connection, the system will only connect to the downloading computer if the
Downloading Access Code matches the Downloading Access Code programmed in the computer file.

[404] Panel Identification Code

Program the 6-digit Panel Identification Code. This code is used by the downloading computer to verify the correct account is calling back
(Call Back feature) or to identify which customer account file should be used (User Initiated DLS and Auto Event Buffer Upload features).

[405] Double-Call Timer

Program the maximum amount of time, in seconds, between calls when connecting to a panel using the double call feature. Valid entries are
[001] to [255].

[406] Number of Rings to Answer On

Program the number of consecutive rings that panel must detect to answer for downloading. Valid entries are [000] to [010].

[499] PC-Link Communications

Enter the following command to initiate downloading via PC-Link: [499] [Installer Code] [499]. Plugging in the PC-Link connector will
automatically initiate the connection if DLS is initiated before connecting the PC-Link Header. The session will NOT be automatically initi-
ated if the system is in installer mode.

22
 Chapter 4 Programming Descriptions

[501] to [514] Programmable Output Attributes

These options are used to customize the operation of the PGM outputs ([501] for PGM 1, [502] for PGM 2 etc.). The available options
depend on which PGM output type has been programmed.
When the PGM Output Options ([009] to [011]) are programmed, the system will change the PGM Attributes to the default settings. The
PGM Attributes will default if a new PGM output option is programmed.
PGM Output Option [01], [03] to [08], [11] to [22], [25],[26], [28], [30], [33], [34]
Option Description
[3] ON: the PGM output will operate normally (switch to ground when activated).
OFF: the PGM output will be grounded and switch to open collector (open circuit) when activated.

PGM Output Option [19] to [22]

Option Description
[4] ON: the PGM output will activate for the duration of the PGM Output Timer when the [✱][7][x] command is performed.
OFF: the PGM output will latch until the [✱][7][x] command is performed again.
[5] ON: a valid user code must be entered after the [✱][7][x] command. OFF: a user code is not required.
PGM Output Option [09]
Option Description
[1] ON: PGM output is activated if a Service Required trouble condition is present.
[2] ON: PGM output is activated if an AC trouble condition is present.
[3] ON: PGM output is activated if a Telephone Line trouble condition is present.
[4] ON: PGM output is activated if a Failure to Communicate trouble condition is present.
[5] ON: PGM output is activated if a Zone Fault condition is present.
[6] ON: PGM output is activated if a Zone Tamper condition is present.
[7] ON: PGM output is activated if a Wireless Low Battery trouble condition is present.
[8] ON: PGM output is activated if a Loss of Clock trouble condition is present.
PGM Output Option [10]
Option Description
[1] ON: PGM output is activated if a Burglary Alarm occurs.
[2] ON: PGM output is activated if a Fire Alarm occurs.
[3] ON: PGM output is activated if a Panic Alarm occurs.
[4] ON: PGM output is activated if a Medical Alarm occurs.
[5] ON: PGM output is activated if a Supervisory Alarm occurs.
[6] ON: PGM output is activated if a Priority Alarm occurs.
[7] ON: PGM output is activated if a 24-Hour Hold-Up Alarm occurs.
[8] ON: the PGM output is activated for the time programmed for the PGM Output Timer.
OFF: the PGM output will latch until a valid user code is entered.

PGM Output Option [31]

Option Description
[1] ON: PGM output is activated if a Fire Alarm occurs.
[2] ON: PGM output is activated if a Panic Alarm occurs.
[3] ON: PGM output is activated if a Burglary Alarm occurs.
[4] ON: PGM output is activated if an Opening/Closing occurs.
[5] ON: PGM output is activated if a zone is automatically bypassed.
[6] ON: PGM output is activated if a Medical Alarm occurs.
[7] ON: PGM output is activated if both a confirmed alarm and a Police Code occur.
[8] ON: the PGM output is active when the selected condition is true. OFF: the PGM output will latch until a valid user code is entered

PGM Output Option [32]

Option Description
[1]-[7] For Future Use
[8] ON: the PGM is activated for the duration programmed in PGM Output Timer.
OFF: the PGM is activated when an Opening After Alarm occurs, and will be deactivated when a valid access code is entered.

23
PowerSeries - PC1616/PC1832/PC1864

PGM Output Option [29] and [35]-[41]

Option Description
[1]-[2] For Future Use
[3] ON: the PGM will switch to ground when the event occurs.
OFF: the PGM will switch to open when the event occurs.
[4]-[7] For Future Use
[8] ON: AND logic is selected, all zones that are enabled must be violated before the PGM will activate.
OFF: OR logic is selected, only one violated zone is required to activate the PGM. All zones must be restored to turn it OFF.
Zones are assigned to this PGM in the PGM Partition Assignment Section [551]-[564]

[551] to [564] PGM Partition Assignment

These sections are used to customize the operation of the PGM outputs ([551] for PGM 1, [552] for PGM 2, etc.). Turn on the desired option
in the correct section to assign the PGM output to a specified partition. PGM outputs can be assigned to more than one partition. For PGM
outputs that are considered ‘system’ outputs (e.g.,Trouble output), programming in these sections will not affect the operation of the PGM
output. Zone Follower PGM types 29 and 35-41 are used to assign specific zones to the PGM.
Each Command Output PGM type can be assigned to one partition only.

[601] to [608] Additional Reporting Codes

Program the reporting code for all events to be transmitted. For information of when each reporting event will be transmitted, refer to
Appendix A – Reporting Codes. The panel also supports Automatic SIA and Automatic Contact ID reporting. Program data [00] to disable
the reporting of an event. If any other data is programmed (Data [01] to [FF]) the panel will automatically generate the correct reporting
event when transmitting to the central station. For all formats excluding Automatic SIA and Automatic Contact ID, the panel will not attempt
to report an event if data [00] or data [FF] is programmed for the reporting code.

[681] to [688] Auto-Disarm Schedules

Program the time to auto-disarm ([681] for Partition 1, [682] for Partition 2, etc.) for each day of the week. Each section has seven, 4-digit
entries: two digits for the hour, two digits for the minute, for Sunday through Saturday. Program using the twenty-four-hour system (for
example, to auto-arm at 8:00 pm program data [20][00]). Valid entries are [00][00] to [23][59] – program [99][99] to disable auto disarming

[691] to [698] Auto-Disarm Holiday Schedule

Program the dates to be used for the Auto-Disarm holiday schedule ([691] for Partition 1, [692] for Partition 2, etc.) Each section has 14, 6-
digit entries: two digits for the month, two digits for the day and two digits for the year. The panel will not disarm on the programmed dates.
The format of entering the date is MMDDYY. Program [99][99][99] to disable the Auto-Disarm holiday schedule.

[700] Automatic Clock Adjust

Program the number of seconds for the last minute of the day. This can be used to make minor corrections to the clock if the AC frequency is
not reliable. Valid entries are [01] to [99].

[701] First International Option Code

Option Description
[1] ON: configures the system for 50Hz AC. OFF: configures the system for 60Hz AC.
[2] ON: the system uses the internal crystal for the internal panel clock. OFF: the system uses the AC frequency for the internal panel clock.
[3] ON: the system will inhibit arming if a Low Battery or AC trouble condition is present. OFF: arming will not be inhibited.
[4] ON: all Tamper troubles will latch and arming will be inhibited. Enter Installer Programming to clear the trouble condition and return
to normal operation. OFF: Tamper troubles will not latch and will not inhibit arming.
[5] ON: all access codes are 6-digits long. OFF: all access codes are 4-digits long.
[6] ON: the system will hang up if a busy tone is detected. This attempt is not counted towards the Maximum Dialing Attempts.
OFF: the panel will not detect busy tones.
[7] ON: the system will charge the battery at approximately 700mA. OFF: the system will charge the battery at 400mA.
[8] ON: the system will abort a DLS session, Escort access, Listen In/Two-way session if a new central station communication event occurs.
OFF: non-critical events (Test transmission, Periodic Test and System Test) will not abort the session. Events will be communicated after
the session is complete.

24
 Chapter 4 Programming Descriptions

[702] Second International Option Code

Option Description
[1] ON: the communicator uses a 33/67 make/break ratio when pulse dialing.
OFF: the system uses a 40/60 make/break ratio.
[2] ON: the system dials regardless of the presence of a dial tone after the first attempt.
OFF: the system dials only if a dial tone is detected.
[3] ON: changes the Test Transmission Cycle Time to minutes.
OFF: sends a Test Transmission after the programmed number of days.
[4] ON: the system accepts 1600Hz handshake pulse formats.
OFF: the system accepts 1400Hz or 2300Hz handshakes.
[5] ON: the system generates a tone for 500ms every 2 seconds, indicating digital equipment is making the call vs. a voice call.
OFF: the system does not generate a tone.
[6] ON: the tone generated (2100Hz.) indicates that digital equipment is making the call.
OFF: the tone is 1300Hz.
[7] ON: the DLS down loading window is 1 hour. OFF: the DLS downloading window is 6 hours.
[8] ON: the system activates the bell output if a Failure to Communicate trouble occurs while the system is armed.
OFF: the system does NOT activate the bell output if a Failure to Communicate trouble occurs while the system is armed.

[703] Delay Between Dialing Attempts

Program the amount of time (in seconds) the panel will wait between dialing attempts to transmit a reporting event to the central station.
Valid entries are [001] to [255].

[800]-[851] Module Programming

The following program options are used to program different modules that can be connected to the control panel. Refer to the relevant Instal-
lation Manual for installation and programming information.
[801]: PC5400 Printer Module Programming
[802]: PC59xx VOX Module Programming
[803]: Alternate Communicator Programming
[804]: Wireless Programming
[805]: PC5100 Addressable Programming
[851]: TL/GS Module Programming

Special Installer Instructions

[898] Wireless Enrollment
Refer to Section 1.12 RFK5500 and RFK5564 Easy Wireless Enrollment Procedure for details.
[899] Template Programming
Selecting [✱][8] [Installer Code] [899] displays the current 5-digit template programming code. Refer to section 3.1 Template Programming for
details. Refer to Appendix E - Template Programming for a detailed description of available templates and corresponding 5-digit codes.
This feature requires a PK55xx or RFK55xx series keypad, v.1.1 or higher.

[900] Panel Version Displayed

Only available with LCD5500 or PK5500 keypads. The system will display the version of the control panel (e.g., [0460] indicates panel ver-
sion 4.60).

[901] Installer Walk Test

The system will turn Installer Walk Test ON. The Ready, Armed and Trouble LED’s will flash rapidly while the test is active. Every time a
zone is violated the system will activate the bell output for two seconds and log the event to the event buffer. To turn Installer Walk Test OFF
enter [901] again. The system automatically terminates the test if there is no zone activity for 15 minutes.

[902] Module Supervision Reset

All modules are automatically detected within one minute after being connected to the Keybus. Enter [902] to clear detected modules if a
module is removed, if PC5108 jumpers are changed, or if a keypad’s slot assignments are programmed. The system will rescan the Keybus
to determine which modules are connected.

25
PowerSeries - PC1616/PC1832/PC1864

[903] View Module Supervision

The keypad will display the modules detected by the system by turning on the associated zone light (LED keypads), flashing the numbers
(fixed-message LCD keypads), or displaying the modules detected in plain language (programmable LCD keypads). Refer to the chart
below:
Indicator Light (Zone) Module
[01] to [08] Keypad in Slot #1 to #8
[09] to [14] PC5108 Zone Expander #1 to #6
[15] PC5100 Module
[16] PC5108 Zone Expander #7
[17] RF5132 Module or RFK keypad with integrated wireless receiver
[18] PC5208
[19] PC5204 Module
[20] PC5400 Module
[21] PC59xx Module
[22] Alternate Communicator
[24] Escort5580 or Escort5580TC
[26] to [29] PC5200 #1 to #4

[904] Wireless Placement Test

Enter [904] followed by the 2-digit number of the wireless zone to test. When a wireless signal is received from the selected transmitter, the
system will indicate the location as Good or Bad, as follows:
Good: One bell squawk, 1 keypad beep, keypad zone light [1] ON
Bad: Three bell squawks, 3 keypad beeps, keypad zone light [3] ON
Press [#] to exit when testing is complete. Enter the 2-digit zone number for the next wireless device to test or press [#] to return to standard
programming.

[989] Default Master Code

Enter [989][Installer Code] to default the Master Code to the factory defaults.

[990] Installer Lockout Enable

Enter [990][Installer Code][990] to enable the Installer Lockout feature. A hardware default cannot be performed when the Installer Lockout
feature is ON. In addition, the system will chatter the line seizure relay 10 times if the panel is powered up, indicating that the feature is ON.

[991] Installer Lockout Disable

Enter [991][Installer Code][991] to turn the Installer Lockout feature OFF.

[993] to [999]: Factory Default Module/Panel

The following options can be used to restore a module or the main control panel to its factory default settings. Enter the appropriate option,
followed by the Installer Code, followed by the option number (e.g., [993][Installer Code][993])
[993]: Factory Default Alternate Communicator
[995]: Factory Default Escort 5580 Module
[996]: Factory Default Wireless Receiver
[997]: Factory Default PC5400 Module
[998]: Factory Default PC59xx Module
[999]: Factory Default Main Control Panel

Hardware Reset (Default) Main Control Panel

Perform the following to restore the main control panel to its default settings:
1. Power down the system.
2. First removing all wires between Zone 1 and PGM1 on the control panel, connect a short between them.
3. Power up the control panel (AC power only) for 10 seconds.
4. Power down the control panel, remove the short between Zone 1 and PGM1.
5. Power up the control panel.

26
 Chapter 4 Programming Descriptions

[001]-[064] Label Programming (Zone 1-64) (applies to PK5500/RFK5500/RFK5564 only)

Zone and other labels in these sections can be customized.
Default labels are in English and do not change when an alternate language is selected.
Labels can be programmed locally or downloaded/uploaded using DLS and Connect 24 interactive software.
To program a zone label: Press To Enter/Display

1. Enter the section number of the label to be pro- [<] Display Left (Previous character position)
grammed. e.g., [*][8][Installer Code][*][001]. [>] Display Right (Next character position)
[✽ ] [SELECT]
2. Scroll to the desired character’s location using the <> [#] [ESCAPE]
Keys. [0] [SPACE]
3. Enter the number of the corresponding character [1] [A], [B], [C], [1]
group until the desired character is displayed. [2] [D], [E], [F], [2]
[3] [G], [H], [I], [3]
Example: [4] [J], [K], [L], [4]
Press the “2” key 3 times to enter the letter “F.” [5] [M], [N], [O], [5]
Press the “2” key 4 times to enter the number [6] [P], [Q], [R], [6]
“2.” [7] [S], [T], [U], [7]
4. Press [ ✱ ] to access the “Select Option” menu. [8] [V], [W], [X], [8]
Scroll to “Save” then press [ ✱ ] to save the label. [9] [Y], [Z], [9], [0]
WORDS - This option provides access to the Label Library, a collection of words commonly used when programming
labels.
ASCII ENTRY - This option is for entering uncommon characters, or as a primary method for programming labels. 255
character entries are available, although some entries are duplicated. Use the [<] [>] keys to scroll through the characters or
enter a 3-digit number from 000-255. Press the [✱] key to enter a character in the label.
CHANGE CASE - This option toggles the letter entry between upper case letters (A, B, C) and lower case letters (a, b, c).
CLEAR TO END - This option clears the display from the character where the cursor is located to the end of the display.
CLEAR DISPLAY - This option sets all characters in a label to “space” or cleared.
SAVE - Saves the new label. If save is not selected before leaving the label programming section, the changes are lost.

Label Library
The Label Library is a database of words commonly used when programming labels. Individual words can be combined as needed. e.g., Front +
Door. Each line of the display supports a maximum of 14 characters. If a word will not fit on a line, scroll right until the cursor appears at the first
character of the second line then add the word.
To program a custom label using the Label Library:
1. Enter keypad programming and select the label to change. e.g., [*][8][Installer Code][*][001] (to program the label for zone 01).
2. Press [*] to open the “Select Options” menu.
3. Press [*] again to select the “Words” option.
4. Enter the 3-digit number corresponding to a word (see Words table below) or use the scroll keys [<][>] to view words in the library.
5. Press [*] to select the word.
6. To add another word, repeat the above procedure from step 2.
7. To add a space, press the right scroll key [>].
8. To clear characters, select “Clear to End” or “Clear Display” from the “Select Options” menu.
9. To save the current label, press [*] to access the “Select Options” menu, scroll left [<] to “Save” then press [*] again.

27
PowerSeries - PC1616/PC1832/PC1864

Words Table
Item Text Item Text Item Text Item Text Item Text Item Text
# # # # # #
001 Aborted 042 Control 083 Garage 124 Motion 165 Shop 206 E
002 AC 043 Date 084 Gas 125 No 166 Side 207 F
003 Access 044 Daughter’s 085 Glass 126 North 167 Siren 208 G
004 Active 045 Degrees 086 Goodbye 127 Not 168 Sliding 209 H
005 Activity 046 Delay 087 Gym 128 Now 169 Smoke 210 I
006 Alarm 047 Den 088 Hallway 129 Number 170 Son’s 211 J
007 All 048 Desk 089 Heat 130 Off 171 Sound 212 K
008 AM 049 Detector 090 Hello 131 Office 172 South 213 L
009 Area 050 Dining 091 Help 132 OK 173 Special 214 M
010 Arm 051 Disarmed 092 High 133 On 174 Stairs 215 N
011 Armed 052 Door 093 Home 134 Open 175 Stay 216 O
012 Arming 053 Down 094 House 135 Opening 176 Sun 217 P
013 Attic 054 Download 095 In 136 Panic 177 Supervisory 218 Q
014 Auxiliary 055 Downstairs 096 Install 137 Partition 178 System 219 R
015 Away 056 Drawer 097 Interior 138 Patio 179 Tamper 220 S
016 Baby 057 Driveway 098 Intrusion 139 Pet 180 Temperature 221 T
017 Back 058 Duct 099 Invalid 140 Phone 181 Test 222 U
018 Bar 059 Duress 100 Is 141 Please 182 Time 223 V
019 Basement 060 East 101 Key 142 PM 183 To 224 W
020 Bathroom 061 Energy Saver 102 Kids 143 Police 184 Touchpad 225 X
021 Battery 062 Enter 103 Kitchen 144 Pool 185 Trouble 226 Y
022 Bedroom 063 Entry 104 Latchkey 145 Porch 186 Unbypass 227 Z
023 Bonus 064 Error 105 Laundry 146 Power 187 Unit 228 (Space)
024 Bottom 065 Exercise 106 Left 147 Press 188 Up 229 ’ (Apostrophe)
025 Breezeway 066 Exit 107 Level 148 Program 189 West 230 - (Dash)
026 Building 067 Exterior 108 Library 149 Progress 190 Window 231 _ (Underscore)
027 Bus 068 Factory 109 Light 150 Quiet 191 Zone 232 *
028 Bypass 069 Failure 110 Lights 151 Rear 192 0 233 #
029 Bypassed 070 Family 111 Living 152 Receiver 193 1 234 :
030 Cabinet 071 Father’s 112 Load 153 Report 194 2 235 /
031 Cancelled 072 Feature 113 Loading 154 RF 195 3 236 ?
032 Car 073 Fence 114 Low 155 Right 196 4
033 Carbon 074 Fire 115 Lower 156 Room 197 5
034 Central 075 First 116 Main 157 Safe 198 6
035 Chime 076 Floor 117 Master 158 Schedule 199 7
036 Closed 077 Force 118 Mat 159 Screen 200 8
037 Closet 078 Foyer 119 Medical 160 Second 201 9
038 Closing 079 Freeze 120 Memory 161 Sensor 202 A
039 Code 080 Front 121 Menu 162 Service 203 B
040 Communicator 081 Furnace 122 Monoxide 163 Shed 204 C
041 Computer 082 Gallery 123 Mother’s 164 Shock 205 D

28
 Chapter 5 Programming Worksheets

Chapter 5 Programming Worksheets

5.1 Index to Programming Worksheets
Programming Option Page Programming Option Page

[000] Keypad Enrollment .......................................................................30 [348] Test Transmission Reporting Codes .................................................44
[001]-[004] Zone Definitions..................................................................30 [349] PC5700 Maintenance Reporting Codes ...........................................44
[005] System Times ................................................................................31 [350] Communicator Format Options .......................................................44
[006] Installer Code ................................................................................31 [351]-[358] Alarm/Restore Communicator Call Directions.......................44
[007] Master Code ..................................................................................31 [359]-[366] Tamper/Restore Communicator Call Directions.....................44
[008] Maintenance Code.........................................................................31 [367]-[374] Opening/Closing Communicator Call Directions ...................45
[009] PGM 1&2 Output Programming (Main Panel) .............................32 [375] System Maintenance Communicator Call Directions ......................45
[010] PGM 3-10 Output Programming (Main Panel/PC5208)...............32 [376] System Test Transmissions Communicator Call Directions .............45
[011] PGM 11-14 Output Programming (PC5204) ................................32 [377] Communication Variables .................................................................45
[012] Keypad Lockout Options .............................................................32 [378] Test Transmission Time of Day .......................................................45
[013] 1st System Options........................................................................33 [379] Periodic DLS Time of Day ...............................................................45
[014] 2nd System Options ......................................................................33 [380] 1st Communicator Options ...............................................................46
[015] 3rd System Options .......................................................................33 [381] 2nd Communicator Options ..............................................................46
[016] 4th System Options .......................................................................33 [382] 3rd Communicator Options...............................................................46
[017] 5th System Options .......................................................................34 [383] 4th Communicator Options...............................................................46
[018] 6th System Options .......................................................................34 [389] TL/GS Module Fault Check Timer ..................................................46
[019] 7th System Options .......................................................................34 [401] DLS Downloading Option Codes .....................................................47
[020] Keypad Zone Assignments ...........................................................34 [402] DLS Downloading Telephone Number (32 Digits) ..........................47
[021] 8th System Options .......................................................................35 [403]-[404] DLS Downloading Access Code / Panel ID Code .................47
[022] 9th System Options .......................................................................35 [405] Answering Machine Double Call Timer ...........................................47
[023] 10th System Options .....................................................................35 [406] Number of Rings to Answer On .......................................................47
[030] Zone Loop Response (Zones 1-8) .................................................35 [499] Initiate PC-Link Downloading..........................................................47
[101] - [164] Zone Attributes..................................................................36 [501]-[502] PGM 1&2 Output Attributes (Main Panel).............................48
[165] Maximum Dialing Attempts to Each Telephone Number.............38 [503]-[504] PGM 3&4 Output Attributes (Main Panel / PC5208).............48
[166] Post Dial Wait for Handshake (All Formats) ...............................38 [505]-[510] PGM 5-10 Output Attributes (5208).......................................48
[167] TL/GS Module Wait for Acknowledgement .................................38 [511]-[514] PGM 11-14 Output Attributes (5204) .....................................48
[168] Set Clock Forward (Daylight Saving Time)..................................39 [551]-[552] PGM 1&2 Output Partition Assignment (Main Panel)...........49
[169] Set Clock Back (Standard Time)...................................................39 [553]-[554] PGM 3&4 Output Partition Assignment
[170] PGM Output Timer .......................................................................39 (Main Panel/PC5208) .................................................................................49
[171] Tamper PGM Output Timer ..........................................................39 [555]-[560] PGM 5-10 Output Partition Assignment (5208) .....................49
[175] Auto-Arm Postpone Timer............................................................39 [561]-[564] PGM 11-14 Output Partition Assignment (5204) ...................49
[176] Cross Zone/Police Code Timer ....................................................39 [601]-[604] Closing (Arming) Reporting Codes, Access Codes 33-95........49
[181]-[188] Automatic Arming Schedule...............................................39 [605]-[608] Opening (Disarming) Reporting Codes, Access Codes 33-95.......50
[190] No Activity Arming Pre-Alert Time .............................................39 [681]-[688] Automatic Disarming Schedule ..............................................50
[191]-[198] No Activity Arming Timers ................................................39 [691]-[698] Auto-Disarm Holiday Schedule ..............................................50
[199] Auto-Arming Pre-Alert Timer ......................................................39 [700] Automatic Clock Adjust ...................................................................51
[201] Partition Selection Mask ...............................................................40 [701] 1st International Options...................................................................51
[202]-[265] Partition 1-8 Zone Assignment ...........................................40 [702] 2nd International Options..................................................................51
[301] 1st Telephone Number (32 Digits) ................................................40 [703] Delay between Dialing Attempts ......................................................51
[302] 2nd Telephone Number (32 Digits)...............................................40 [801] PC5400 Printer Module Programming .............................................52
[303] 3rd Telephone Number (32 Digits) ...............................................40 [802] PC59xx VOX Programming .............................................................52
[304] Call Waiting Cancel String (6 Digits) ...........................................40 [804] Wireless Expansion Programming ....................................................52
[310] System Account Code ...................................................................41 [805] PC5100 Programming.......................................................................52
[311]-[318] Partition 1-8 Account Numbers...........................................41 [851] TL/GS Programming.........................................................................52
[320]-[323] Alarm Reporting Codes, Zones 01-64.................................41 [898] Wireless Enrollment..........................................................................52
[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64 ..................41 [899] Template Programming.....................................................................52
[328] Miscellaneous Alarm Reporting Codes.........................................42 [900] Panel Version Displayed ...................................................................52
[329] Priority Alarm and Restoral .........................................................42 [901] Installer Walk Test Mode Enable/Disable ........................................52
[330]-[333] Tamper Reporting Codes, Zones 01-64...............................42 [902] Module Supervision Reset ...............................................................52
[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64 ................42 [903] Module Supervision Field ................................................................52
[338] Miscellaneous Tamper Reporting Codes ......................................43 [904] Wireless Module Placement Test .....................................................52
[339]-[340] Closing (Arming) Reporting Codes, [989] Default Master Code .........................................................................52
Access Codes 1-32.................................................................................43 [990] Installer Lockout Enable ...................................................................52
[341] Miscellaneous Closing (Arming) Reporting Codes ......................43 [991] Installer Lockout Disable ..................................................................52
[342]-[343] Opening (Disarming) Reporting Codes, [993] Restore Alternate Communicator to Default Programming .............52
Access Codes 1-32.................................................................................43 [995] Restore Escort5580 to Default Programming ...................................52
[344] Miscellaneous Opening (Disarming) Reporting Codes ................43 [996] Restore RF5132 to Default Programming ........................................52
[345] Maintenance Alarm Reporting Codes ...........................................43 [997] Restore PC5400 to Default Programming ........................................52
[346] Maintenance Restoral Reporting Codes .......................................43 [998] Restore PC59xx to Default Programming ........................................52
[347] Miscellaneous Maintenance Reporting Codes ..............................44 [999] Restore Control Panel to Default Programming ...............................52

29
PowerSeries - PC1616/PC1832/PC1864

Programming Worksheets
Shaded programming sections indicate minimum programming requirements

The defaults for SIA FAR CP-01 are indicated in gray text.

Keypad Partition /Slot and Function Key Programming

[000] Keypad Enrollment
This must be done at each keypad requiring programming.
[0] Slot address (For the partition, 0-8; for the slot, 1-8. For example, to enroll a keypad in partition 3, slot 1, enter (31).)
[1] Function Key 1 Assignment (Valid entries are 00-32)
[2] Function Key 2 Assignment (Valid entries are 00-32)
[3] Function Key 3 Assignment (Valid entries are 00-32)
[4] Function Key 4 Assignment (Valid entries are 00-32)
[5] Function Key 5 Assignment (Valid entries are 00-32)
Function Key Options (enter these values below in the table immediately following):
00 Not used 12 [✱][6] User Functions 24 Recall Bypass Group
01 Select Partition 1 13 Command Output #1 [✱][7][1] 25 For Future Use
02 Select Partition 2 14 Command Output #2 [✱][7][2]/Sensor Reset 26 Time and Date
03 Stay Arm 15 Global Stay Arming 27 Select Partition 3
04 Away Arm 16 [✱][0] Quick Exit 28 Select Partition 4
05 [✱][9] No-Entry Arm 17 [✱][1] Reactivate Stay/Away Zones 29 Select Partition 5
06 [✱][4] Chime On / Off 18 Global Away Arming 30 Select Partition 6
07 [✱][6][——][4] System Test 19 Command Output 3 [✱][7][3] 31 Select Partition 7
08 [✱][1] Bypass Mode 20 For Future Use 32 Select Partition 8
09 [✱][2] Trouble Display 21 Command Output 4 [✱][7][4] 33 For Future Use
10 [✱][3] Alarm Memory 22 Global Disarming
11 [✱][5] Access Code Programming 23 Bypass Recall

[20] Zone
Partition/Slot Key 1 Key 2 Key 3 Key 4 Key 5
Assigned
ICON / LED Defaults 11 00 03 04 06 14 16

Full Message Defaults 18 00 03 04 06 14 16

KEYPAD 1 00

KEYPAD 2 00

KEYPAD 3 00

KEYPAD 4 00

KEYPAD 5 00

KEYPAD 6 00

KEYPAD 7 00

KEYPAD 8 00

[001]-[004] Zone Definitions (enter the values below in the table immediately following):
00 Null Zone (Not Used) 13 24-hr Gas* 26 24-hr Non-alarm*
01 Delay 1* 14 24-hr Heating* 29 Auto-Verified Fire
02 Delay 2* 15 24-hr Auxiliary (Medical)* 30 Fire Supervisory
03 Instant* 16 24-hr Panic* 31 Day Zone*
04 Interior* 17 24-hr Emergency* 32 Instant Stay/Away*
05 Interior, Stay/Away* 18 24-hr Sprinkler* 35 24-hr Bell/Buzzer
06 Delay, Stay/Away* 19 24-hr Water* 36 24-hr Non-Latching Tamper Zone
07 Delayed 24-hr Fire (Hardwired)** 20 24-hr Freeze* 37 Night Zone
08 Standard 24-hr Fire (Hardwired) 21 24-hr Latching Tamper* 39 For Future Use
09 24-hr Supervisory 22 Momentary Keyswitch Arm* 41 24-hr Carbon Monoxide (hardwired)
10 24-hr Supervisory Buzzer* 23 Maintained Keyswitch Arm* 81 24-hr Wireless Carbon Monoxide
11 24-hr Burglary* 24 For Future Use 87 Delay 24-hr Fire (Wireless/Addressable)**
12 24-hr Holdup* 25 Interior/Delay* 88 Standard 24-hr Fire (Wireless/Addressable)**
*For burglary applications only ** For residential fire applications only

30
 Chapter 5 Programming Worksheets

Section Zone Def. Section Zone Def. Section Zone Def. Section Zone Def.
[001] 01 01 I_____I_____I [002] 17 00 I_____I_____I [003] 33 00 I_____I_____I [004] 49 00 I_____I_____I
02 03 I_____I_____I 18 00 I_____I_____I 34 00 I_____I_____I 50 00 I_____I_____I
03 03 I_____I_____I 19 00 I_____I_____I 35 00 I_____I_____I 51 00 I_____I_____I
04 03 I_____I_____I 20 00 I_____I_____I 36 00 I_____I_____I 52 00 I_____I_____I
05 04 I_____I_____I 21 00 I_____I_____I 37 00 I_____I_____I 53 00 I_____I_____I
06 04 I_____I_____I 22 00 I_____I_____I 38 00 I_____I_____I 54 00 I_____I_____I
07 04 I_____I_____I 23 00 I_____I_____I 39 00 I_____I_____I 55 00 I_____I_____I
08 04 I_____I_____I 24 00 I_____I_____I 40 00 I_____I_____I 56 00 I_____I_____I
09 00 I_____I_____I 25 00 I_____I_____I 41 00 I_____I_____I 57 00 I_____I_____I
10 00 I_____I_____I 26 00 I_____I_____I 42 00 I_____I_____I 58 00 I_____I_____I
11 00 I_____I_____I 27 00 I_____I_____I 43 00 I_____I_____I 59 00 I_____I_____I
12 00 I_____I_____I 28 00 I_____I_____I 44 00 I_____I_____I 60 00 I_____I_____I
13 00 I_____I_____I 29 00 I_____I_____I 45 00 I_____I_____I 61 00 I_____I_____I
14 00 I_____I_____I 30 00 I_____I_____I 46 00 I_____I_____I 62 00 I_____I_____I
15 00 I_____I_____I 31 00 I_____I_____I 47 00 I_____I_____I 63 00 I_____I_____I
16 00 I_____I_____I 32 00 I_____I_____I 48 00 I_____I_____I 64 00 I_____I_____I

[005] System Times

Valid entries for Entry Delay are 030-255; valid entries for Exit Delay are 045-255 for SIA CP-01.
[01] Partition 1 Entry/Exit times [05] Partition 5 Entry/Exit times
030 I____I____I____I Entry Delay 1 030 I____I____I____I Entry Delay 1
045 I_0_I_3_I_0_I Entry Delay 2 045 I_0_I_3_I_0_I Entry Delay 2
120 I_0_I_6_I_0_I Exit Delay 120 I_0_I_6_I_0_I Exit Delay

[02] Partition 2 Entry/Exit times [06] Partition 6 Entry/Exit times

030 I____I____I____I Entry Delay 1 030 I____I____I____I Entry Delay 1
045 I_0_I_3_I_0_I Entry Delay 2 045 I_0_I_3_I_0_I Entry Delay 2
120 I_0_I_6_I_0_I Exit Delay 120 I_0_I_6_I_0_I Exit Delay

[03] Partition 3 Entry/Exit times [07] Partition 7 Entry/Exit times

030 I____I____I____I Entry Delay 1 030 I____I____I____I Entry Delay 1
045 I_0_I_3_I_0_I Entry Delay 2 045 I_0_I_3_I_0_I Entry Delay 2
120 I_0_I_6_I_0_I Exit Delay 120 I_0_I_6_I_0_I Exit Delay

[04] Partition 4 Entry/Exit times [08] Partition 8 Entry/Exit times

030 I____I____I____I Entry Delay 1 030 I____I____I____I Entry Delay 1
045 I_0_I_3_I_0_I Entry Delay 2 045 I_0_I_3_I_0_I Entry Delay 2
120 I_0_I_6_I_0_I Exit Delay 120 I_0_I_6_I_0_I Exit Delay

[09] Bell Cut-Off Timer (All Partitions)

004 I___I___I___I Enter 3 digits from 001-255

For SIA CP-01 compliant installations, the Exit Delay must be within the range of 045-255 seconds (Default 60 seconds). If the Exit
Delay is silent (Section 14, Option 6 or Stay Function Key Arming), the exit delay must be twice the programmed value. It cannot, however,
exceed 255 seconds (i.e., 090-255 seconds).
For UL Installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds.

Exit Time Restart shall be disabled when the panel is used in combination with T-Link TL250/TL300.

[006] Installer’s Code [007] Master Code [008] Maintenance Code

Default Default Default
5555 I_______I_______I_______I_______I 1234I_______I_______I_______I_______I AAAAI_______I_______I_______I_______I

[007] Master Code

The master code can be restored to default in section [989] Default Master Code.

31
PowerSeries - PC1616 PC1 2 PC1 64

Programmable utput ptions

01 esidential Burglary and Fire Bell utput 1 Stay Armed Status 6 one Follower utput ones 17-24
02 For Future Use 1 Command utput 1 7 1 7 one Follower utput ones 25- 2
0 Sensor eset 7 2 20 Command utput 2 7 2 one Follower utput ones -40
04 2-Wire Smoke Support PGM 2 only 21 Command utput 7 one Follower utput ones 41-4
05 System Armed Status 22 Command utput 4 7 4 40 one Follower utput ones 4 -56
06 eady o Arm 2 24- r Silent Input PGM 2 only 41 one Follower utput ones 57-64
07 eypad Bu er Follow Mode 24 24- r Audible Input PGM 2 only
0 Courtesy Pulse 25 Delayed Fire and Burglary utput
0 System rouble utput wit rouble options 26 Battery est utput
utput types 0 , 04
10 System ent Strobe wit ent options 2 oldup utput
and 20 cannot be used
11 System amper all sources 2 one Follower utput ones 1- toget er on t e same
12 LM and Alarm 0 Partition Status Alarm Memory system.
1 isso utput 1 Alternate Communicator
14 Ground Start Pulse 2 For Future Use
15 emote peration DLS Support For Future Use
16 For Future Use 4 Away Armed wit no one Bypassed Status
17 Away Armed Status 5 one Follower utput ones -16)
00 PGM1 and PGM2 utput Programming Main Panel
Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564].

PC1616 and PC1832 have 2 onboard PGMs (PGM 1 and 2). PC1864 has 4 on-board PGMs (PGM 1-4).
Default Default
19 I_______I_______I PGM 1 10 I_______I_______I PGM 2

010 PGM to PGM10 utput Programming Main Panel PC520

Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
Default Default
01 I_______I_______I PGM 3 (main panel/PC5208)* 01 I_______I_______I PGM 7 (PC5208)
01 I_______I_______I PGM 4 (main panel/PC5208)* 01 I_______I_______I PGM 8 (PC5208)
01 I_______I_______I PGM 5 (PC5208) 01 I_______I_______I PGM 9 (PC5208)
01 I_______I_______I PGM 6 (PC5208) 01 I_______I_______I PGM 10 (PC5208)
ese two sections abo e allow you to program bot PGM and PGM4 on t e main panel and t e irst two PGM outputs on t e
PC520 . I you use bot t e main panel and t e PC520 outputs PGM will work identically to t e irst PC520 output and PGM4
will work identically to t e second PC520 output.
011 PGM 11 to PGM 14 utput Programming PC5204
Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
Default Default
01 I_______I_______I PGM 11 01 I_______I_______I PGM 13
01 I_______I_______I PGM 12 01 I_______I_______I PGM 14

t er System ptions
012 eypad Lockout ptions
If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.
Default
000 I_______I_______I_______I umber o In alid Codes Be ore Lockout 001-255 codes 000 to disable
000 I_______I_______I_______I Lockout Duration 000-255 minutes

32
 Chapter 5 Programming Worksheets

[013] First System Options

Opt Def ON OFF

1 ❏ Normally Closed Loops ❏ End-of-Line Resistors

2 ❏ Double End-of-Line Resistors ❏ Single End-of-Line Resistors
3 ❏ Panel shows all Troubles when armed ❏ Panel shows only Fire Troubles when armed
4 ❏ Tampers/Faults do not show as open ❏ Tampers/Faults show as open
5 ❏ Auto-Arm Schedule in [*][6] and installers ❏ Auto-arm Schedule in Installer Programming Only
6 ❏ Audible Exit Fault Enabled ❏ Audible Exit Fault Disabled
7 ❏ Event Buffer Follows Swinger Shutdown ❏ Event Buffer Logs Events past Shutdown
8 ❏ Temporal Three Fire Signal Enabled ❏ Standard Pulsed Fire Signal
[014] Second System Options
Opt Def ON OFF

1 ❏ Arm /Disarm Bell Squawk Enabled ❏ Arm /Disarm Bell Squawk Disabled

2 ❏ Bell Squawk During Auto-Arm ❏ No Bell Squawk During Auto-Arm

3 ❏ Bell Squawk On Exit Delay ❏ No Bell Squawk On Exit Delay

4 ❏ Bell Squawk On Entry Delay ❏ No Bell Squawk On Entry Delay

5 ❏ Bell Squawk On Trouble ❏ No Bell Squawk On Trouble

6 ❏ Audible Exit with Urgency ❏ Silent Exit Delay

7 ❏ Exit Delay Termination Enabled ❏ Exit Delay Termination Disabled

8 ❏ Residential Fire Bell is Continuous ❏ Residential Fire Bell is Cut-off

[015] Third System Options

Opt Def ON OFF

1 ❏ Fire Key Enabled ❏ Fire Key Disabled

2 ❏ Panic Key Audible (Bell / Beeps) ❏ Panic Key Silent

3 ❏ Quick Exit Enabled (ON for SIA CP-01) ❏ Quick Exit Disabled

4 ❏ Quick Arming Enabled (No Code Required) ❏ Quick Arming Disabled (Code Required)

5 ❏ Code Required for Bypassing ❏ Code Not Required for Bypassing

6 ❏ Master Code NOT Changeable ❏ Master Code Changeable

7 ❏ TLM Enabled ❏ TLM Disabled

8 ❏ TLM Audible (Bell) when Armed ❏ TLM Trouble Beeps when Armed

[016] Fourth System Options

Opt Def ON OFF

1 ❏ AC Trouble Displayed ❏ AC Trouble Not Displayed

2 ❏ Trouble Light Flashes if AC Fails ❏ Trouble Light does NOT follow AC Status

3 ❏ Blank Keypad when Not Used ❏ Keypad Blanking Disabled

4 ❏ Code required to remove Keypad Blanking ❏ No Code Required

5 ❏ Keypad Backlighting is Enabled ❏ Keypad Backlighting is Disabled

6 ❏ Power Save Mode Enabled ❏ Power Save Mode Disabled

7 ❏ Bypass Status Displayed While Armed ❏ Bypass Status Not Displayed While Armed

8 ❏ Keypad Tampers Enabled ❏ Keypad Tampers Disabled

33
PowerSeries - PC1616/PC1832/PC1864

[017] Fifth System Options

Opt Def ON OFF

1 ❏ WLS Key Does Not use Access Codes ❏ WLS Key Uses Access Codes

2 ❏ RF Jam Log after 5 Minutes ❏ RF Jam Log after 30 Seconds

3 ❏ Audible RF Jam Trouble Beeps ❏ Silent RF Jam Trouble Beeps

4 ❏ Double Hit Enabled ❏ Double Hit Disabled

5 ❏ Late to Close Enabled ❏ Late to Close Disabled

6 ❏ Daylight Saving Time Enabled ❏ Daylight Saving Time Disabled

7 ❏ For Future Use ❏

8 ❏ Squawk on Away Key Arming/Disarming Only ❏ Squawk on all Arming/Disarming

[018] Sixth System Options

Opt Def ON OFF
1 ❏ Test Transmission Exception Enabled ❏ Test Transmission Exception Disabled

2 ❏ For Future Use ❏

3 ❏ For Future Use ❏
4 ❏ For Future Use ❏
5 ❏ Keypad Buzzer Follows Bell Enabled ❏ Keypad Buzzer Follows Bell Disabled

6 ❏ Cross Zoning Enabled ❏ Police Code Enabled

7 ❏ Exit Delay Restart Enabled (Enabled for SIA CP-01) ❏ Exit Delay Restart Disabled

8 ❏ AC Trouble Beeps Enabled ❏ AC Trouble Beeps Disabled

[019] Seventh System Options

Opt Def ON OFF

1 ❏ For Future Use ❏

2 ❏ For Future Use ❏
3 ❏ First Zone in Alarm Enabled ❏ First Zone in Alarm Disabled

4 ❏ For Future Use ❏

5 ❏ For Future Use ❏
6 ❏ Green Keypad LED Power Indication ❏ Ready Indication

7 ❏ [✱][6] Accessible by All Users ❏ Master Code Only

8 ❏ For Future Use ❏

Keypad Zone Assignments

[020] Keypad Zone Assignments
Only one keypad may be assigned to a zone. Only one keypad may be
Default assigned to a slot. Only one
00 I________I_______I Keypad (slot 1) Zone zone can be assigned to a
keypad. Valid entries are
00 I________I_______I Keypad (slot 2) Zone from 01 to 64.
00 I________I_______I Keypad (slot 3) Zone
00 I________I_______I Keypad (slot 4) Zone
00 I________I_______I Keypad (slot 5) Zone
00 I________I_______I Keypad (slot 6) Zone
00 I________I_______I Keypad (slot 7) Zone
00 I________I_______I Keypad (slot 8) Zone

34
 Chapter 5 Programming Worksheets

[021] Eighth System Options

Opt Def ON OFF

1 ❏ Access Code Entry Blocked During Entry Delay ❏ Access Code Entry Not Blocked During Entry Delay

2 ❏ For Future Use ❏

3 ❏ For Future Use ❏
4 ❏ For Future Use ❏
5 ❏ For Future Use ❏
6 ❏ Keyswitch Disarming During Entry Delay Only ❏ Keyswitch Disarming at Any Time

7 ❏ For Future Use ❏

8 ❏ For Future Use ❏
[022] Ninth System Options
Opt Def ON OFF
1 ❏ Access Code Req’d for [✱][1], [✱][2], [✱][3] ❏ No Access Code Req’d for [✱][1], [✱][2], [✱][3]

2 ❏ For Future Use ❏

3 ❏ For Future Use ❏
4 ❏ Master Code Bypasses Holdup Zones Only ❏ Any Code Bypasses Holdup Zones

5 ❏ For Future Use ❏

6 ❏ RF Delinquency enabled ❏ RF Delinquency disabled

7 ❏ For Future Use ❏

8 ❏ Audible Exit Delay for Stay Arming ❏ Stay Arming Silent

[023] Tenth System Options

Opt Def ON OFF
1 ❏ Fire Key Beeps Only ❏ Fire Key Beeps and Sounds Bell

2 ❏ For Future Use ❏

3 ❏ Test Transmission While Armed Only ❏ Test Transmission While Armed/Disarmed

4 ❏ Test Transmission in Hours ❏ Test Transmission in Days

5 ❏ Switching from AWAY to STAY disabled ❏ AWAY to STAY toggle Option Permitted

6 ❏ 2-way Audio will Not Disconnect for a New Event ❏ 2-way Audio will Disconnect for a New Event

7 ❏ Trouble Beeps are Silent* ❏ Trouble Beeps sound every 10 seconds

8 ❏ Keyswitch Arm in Away Mode ❏ Keyswitch arms in STAY or AWAY

* This option must be off for UL residential fire applications

[030] Zone Loop Response (Zones 1-8)

Opt Def ON OFF
1 ❏ Zone 1 is Fast Loop Response ❏ Zone 1 is Normal Loop Response

2 ❏ Zone 2 is Fast Loop Response ❏ Zone 2 is Normal Loop Response

3 ❏ Zone 3 is Fast Loop Response ❏ Zone 3 is Normal Loop Response

4 ❏ Zone 4 is Fast Loop Response ❏ Zone 4 is Normal Loop Response

5 ❏ Zone 5 is Fast Loop Response ❏ Zone 5 is Normal Loop Response

6 ❏ Zone 6 is Fast Loop Response ❏ Zone 6 is Normal Loop Response

7 ❏ Zone 7 is Fast Loop Response ❏ Zone 7 is Normal Loop Response

8 ❏ Zone 8 is Fast Loop Response ❏ Zone 8 is Normal Loop Response

35
PowerSeries - PC1616/PC1832/PC1864

[101]-[164] Zone Attributes

Zone Attribute Defaults (Y = Option ON; N = Option OFF): Bold entries are opposite for SIA CP-01
Attribute: 1 2 3 4 5 6 7 8 9
ON Audible Steady Chime Bypass Force* Swing Tx. Delay Wireless Zn Cross Zn

OFF Silent Pulsed No No No No No No No

Zone Type:
00 Null Zone N N N N N N N N N
01 Delay 1 Y Y Y Y N Y N N N
02 Delay 2 Y Y Y Y N Y N N N
03 Instant Y Y Y Y N Y N N N
04 Interior Y Y N Y N Y N N N
05 Int. Stay/Away Y Y N Y Y Y N N N
06 Dly. Stay/Away Y Y N Y Y Y N N N
07 Dly. 24hr Fire (Hardw.) Y N N N N N N N N
08 Stand. 24hr Fire (Hardw.) Y N N N N N N N N
09 24hr Superv. N Y N N Y N N N N
10 24hr Superv. Buzzer N Y N Y N N N N N
11 24hr Burglary Y Y N Y N N N N N
12 24hr Holdup N Y N N N N N N N
13 24hr Gas Y N N N N N N N N
14 24hr Heating Y N N N N N N N N
15 24hr Auxiliary (Medical) Y Y N N N N N N N
16 24hr Panic Y Y N N N N N N N
17 24hr Emergency Y Y N N N N N N N
18 24hr Sprinkler Y Y N N N N N N N
19 24hr Water Y Y N N N N N N N
20 24hr Freeze Y Y N N N N N N N
21 24hr Latching Tamper Y Y N N N N N N N
22 Momentary Keyswitch N N N N Y N N N N
23 Maintained Keyswitch N N N N Y N N N N
25 Interior/Delay Y Y N Y N Y N N N
26 24hr Non-alarm N N N N Y N N N N
29 Auto Verified Fire Y N N N N N N N N
30 Fire Supervisory N N N N N N N N N
31 Day Zone Y Y N Y Y Y Y N N
32 Instant Stay/Away Y Y N Y N N N N N
35 24 hr Bell/Buzzer Y Y N Y N Y N N N
36 24hr Non Latching Tamper N Y N N N Y N N N
37 Night Zone Y Y N Y Y Y N N N
41 24hr Carbon Monoxide Y N N N N N N N N
81 24hr Carbon Monoxide (WLS) Y N N N N N N Y N
87 Dly. 24hr Fire (Wireless) Y N N N N N N Y N
88 Stand. 24hr Fire (Wireless) Y N N N N N N Y N

* For UL installations, do not change attribute 5 (Force Arming) from the default setting.

Attribute: 10 11 12 13 14 15 16
ON Zone Attributes 10-13 For Future Use NC Loops SEOL DEOL

OFF Config. Config. Config.

Zone Type:
00 Null Zone N N N N N N N
01 Delay 1 N N N N N N N
02 Delay 2 N N N N N N N
03 Instant N N N N N N N
04 Interior N N N N N N N
05 Int. Stay/Away N N N N N N N
06 Dly. Stay/Away N N N N N N N
07 Dly. 24hr Fire (Hardw.) N N N N N Y N
08 Stand. 24hr Fire (Hardw.) N N N N N Y N
09 24hr Superv. N N N N N N N
10 24hr Superv. Buzzer N N N N N N N
11 24hr Burglary N N N N N N N
12 24hr Holdup N N N N N N N
13 24hr Gas N N N N N N N
14 24hr Heating N N N N N N N
15 24hr Medical N N N N N N N
16 24hr Panic N N N N N N N
17 24hr Emergency N N N N N N N
18 24hr Sprinkler N N N N N N N

36
 Chapter 5 Programming Worksheets

Attribute: 10 11 12 13 14 15 16
ON Zone Attributes 10-13 For Future Use NC Loops SEOL DEOL

OFF Config. Config. Config.

19 24hr Water N N N N N N N
20 24hr Freeze N N N N N N N
21 24hr Latching Tamper N N N N N N N
22 Momentary Keyswitch N N N N N N N
23 Maintained Keyswitch N N N N N N N
25 Interior Delay N N N N N N N
26 24hr Non-alarm N N N N N N N
29 Auto Verified Fire N N N N N N N
30 Fire Supervisory N N N N N N N
31 Day Zone N N N N N N N
32 Instant Stay/Away N N N N N N N
35 24hr Bell/Buzzer N N N N N N N
36 24hr Non Latching Tamper N N N N N N N
37 Night Zone N N N N N N N
41 24hr Carbon Monoxide N N N N N Y N
81 24hr Carbon Monoxide (Wireless) N N N N N N N
87 Dly. 24hr Fire (Wireless) N N N N N N N
88 Stand. 24hr Fire (Wireless) N N N N N N N

Section Zone # Zone Audible/ Steady/ Chime Bypass Force* Swing Tx. Delay Wireless Cross Zn
Type** Silent Pulsed No No No No No No No
1 2 3 4 5 6 7 8 9
[101] 01 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[102] 02 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[103] 03 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[104] 04 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[105] 05 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[106] 06 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[107] 07 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[108] 08 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[109] 09 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[110] 10 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[111] 11 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[112] 12 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[113] 13 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[114] 14 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[115] 15 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[116] 16 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[117] 17 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[118] 18 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[119] 19 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[120] 20 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[121] 21 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[122] 22 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[123] 23 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[124] 24 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[125] 25 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[126] 26 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[127] 27 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[128] 28 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[129] 29 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[130] 30 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[131] 31 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[132] 32 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[133] 33 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[134] 34 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

37
PowerSeries - PC1616/PC1832/PC1864

Section Zone # Zone Audible/ Steady/ Chime Bypass Force* Swing Tx. Delay Wireless Cross Zn
Type** Silent Pulsed No No No No No No No
1 2 3 4 5 6 7 8 9
[135] 35 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[136] 36 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[137] 37 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[138] 38 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[139] 39 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[140] 40 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[141] 41 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[142] 42 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[143] 43 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[144] 44 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[145] 45 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[146] 46 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[147] 47 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[148] 48 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[149] 49 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[150] 50 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[151] 51 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[152] 52 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[153] 53 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[154] 54 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[155] 55 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[156] 56 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[157] 57 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[158] 58 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[159] 59 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[160] 60 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[161] 61 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[162] 62 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[163] 63 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

[164] 64 ( ) I________I I________| I________| I________| I________| I________| I________| I________I I________I

Section Zone # Zone For Future For Future For Future For Future NC Loops SEOL DEOL
Type** Use Use Use Use Config. Config. Config.
10 11 12 13 14 15 16
[101] 01 ( ) I________I I________| I________| I________| I________| I________| I________|

[102] 02 ( ) I________I I________| I________| I________| I________| I________| I________|

[103] 03 ( ) I________I I________| I________| I________| I________| I________| I________|

[104] 04 ( ) I________I I________| I________| I________| I________| I________| I________|

[105] 05 ( ) I________I I________| I________| I________| I________| I________| I________|

[106] 06 ( ) I________I I________| I________| I________| I________| I________| I________|

[107] 07 ( ) I________I I________| I________| I________| I________| I________| I________|

[108] 08 ( ) I________I I________| I________| I________| I________| I________| I________|

**Record here based on programming in sections [001]-[004].

Zone attributes 10-16 only apply to zones 1-8.

System Timers
[165] Maximum Dialing Attempts to Each Telephone Number
Default 005 I_______I_______I_______I Valid entries are 001-005 attempts
For UL Listed Installations, 5 dialing attempts are required.
[166] Post Dial Wait for Handshake (All Formats)
Default 040 I_______I_______I_______I Valid entries are 001-255 seconds
[167] TL/GS Module Wait for Acknowledgement
Default 060 I_______I_______I_______I Valid entries are 060-255 seconds

38
 Chapter 5 Programming Worksheets

[168] Set Clock Forward (Daylight Saving Time)

Def 003 Month |_______|_______|_______| Valid Entries 001-012
Def 002 Week |_______|_______|_______| Valid Entries 000-005
Def 000 Day |_______|_______|_______| Valid Entries 000-031
Def 002 Hour |_______|_______|_______| Valid Entries 000-023
Def 001 Increment |_______|_______|_______| Valid Entries 001-002
[169] Set Clock Back (Standard Time)
Def 011 Month |_______|_______|_______| Valid Entries 001-012
Def 001 Week |_______|_______|_______| Valid Entries 000-005
Def 000 Day |_______|_______|_______| Valid Entries 000-031
Def 002 Hour |_______|_______|_______| Valid Entries 000-023
Def 001 Decrement |_______|_______|_______| Valid Entries 001-002

[170] PGM Output Timer

Default 005 I_______I_______I_______I Valid entries are 001-255 seconds
[171] Tamper PGM Output Timer
Default 000 I_______I_______I_______I Valid entries are 000-255 minutes
[175] Auto-arm Postpone Timer
Default 000 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables automatic arming
[176] Cross Zone/Police Code Timer
Default 060 I_______I_______I_______I Valid entries are 001-255 seconds/minutes; 000 for armed-to-armed period for Police Code

Automatic Arming Schedule

Enter a four-digit number (HH:MM) for each day that the system will Auto-Arm on each partition ([181] for Partition 1 through [188] for Parti-
tion 8). All entries are disabled (9999) by default. Valid entries are 0000-2359.
Sunday Monday Tuesday Wednesday Thursday Friday Saturday

[181] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[182] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[183] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[184] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[185] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[186] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[187] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[188] I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

[190] No Activity Arming Pre-Alert Time

Default Partition
001 All I_______I_______I_______I Valid entries are 001-255 minutes; 000 for no pre-alert
No Activity Arming Timers - Default is [000] for all partitions
Section Partition
[191] 1 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[192] 2 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[193] 3 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[194] 4 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[195] 5 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[196] 6 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[197] 7 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[198] 8 I_______I_______I_______I Valid entries are 001-255 minutes; 000 disables
[199] Auto-arming Pre-Alert Timer
Default: 004 I_______I_______I_______I Valid entries are 001-255 minutes

39
PowerSeries - PC1616/PC1832/PC1864

Partition Programming
[201] Partition Selection Mask
Opt Def ON OFF
1 ❏ Partition 1 is enabled ❏ Cannot be disabled

2 ❏ Partition 2 is enabled ❏ Disabled

3 ❏ Partition 3 is enabled ❏ Disabled

4 ❏ Partition 4 is enabled ❏ Disabled

5 ❏ Partition 5 is enabled ❏ Disabled

6 ❏ Partition 6 is enabled ❏ Disabled

7 ❏ Partition 7 is enabled ❏ Disabled

8 ❏ Partition 8 is enabled ❏ Disabled

For the PC1864 and PC1832, the default setting is partition 1, zones 1-16 ON. For the PC1616, the default setting is par-
tition 1, zones 1-6 ON.

Partition 1 Zone Assignment Partition 2 Zone Assignment Partition 3 Zone Assignment Partition 4 Zone Assignment

[202] 1-8 ❏❏❏❏❏❏❏❏ [210] 1-8 ❏❏❏❏❏❏❏❏ [218] 1-8 ❏❏❏❏❏❏❏❏ [226] 1-8 ❏❏❏❏❏❏❏❏
[203] 9-16 ❏❏❏❏❏❏❏❏ [211] 9-16 ❏❏❏❏❏❏❏❏ [219] 9-16 ❏❏❏❏❏❏❏❏ [227] 9-16 ❏❏❏❏❏❏❏❏
[204] 17-24 ❏❏❏❏❏❏❏❏ [212] 17-24 ❏❏❏❏❏❏❏❏ [220] 17-24 ❏❏❏❏❏❏❏❏ [228] 17-24 ❏❏❏❏❏❏❏❏
[205] 25-32 ❏❏❏❏❏❏❏❏ [213] 25-32 ❏❏❏❏❏❏❏❏ [221] 25-32 ❏❏❏❏❏❏❏❏ [229] 25-32 ❏❏❏❏❏❏❏❏
[206] 33-40 ❏❏❏❏❏❏❏❏ [214] 33-40 ❏❏❏❏❏❏❏❏ [222] 33-40 ❏❏❏❏❏❏❏❏ [230] 33-40 ❏❏❏❏❏❏❏❏
[207] 41-48 ❏❏❏❏❏❏❏❏ [215] 41-48 ❏❏❏❏❏❏❏❏ [223] 41-48 ❏❏❏❏❏❏❏❏ [231] 41-48 ❏❏❏❏❏❏❏❏
[208] 49-56 ❏❏❏❏❏❏❏❏ [216] 49-56 ❏❏❏❏❏❏❏❏ [224] 49-56 ❏❏❏❏❏❏❏❏ [232] 49-56 ❏❏❏❏❏❏❏❏
[209] 57-64 ❏❏❏❏❏❏❏❏ [217] 57-64 ❏❏❏❏❏❏❏❏ [225] 57-64 ❏❏❏❏❏❏❏❏ [233] 57-64 ❏❏❏❏❏❏❏❏

Partition 5 Zone Assignment Partition 6 Zone Assignment Partition 7 Zone Assignment Partition 8 Zone Assignment

[234] 1-8 ❏❏❏❏❏❏❏❏ [242] 1-8 ❏❏❏❏❏❏❏❏ [250] 1-8 ❏❏❏❏❏❏❏❏ [258] 1-8 ❏❏❏❏❏❏❏❏
[235] 9-16 ❏❏❏❏❏❏❏❏ [243] 9-16 ❏❏❏❏❏❏❏❏ [251] 9-16 ❏❏❏❏❏❏❏❏ [259] 9-16 ❏❏❏❏❏❏❏❏
[236] 17-24 ❏❏❏❏❏❏❏❏ [244] 17-24 ❏❏❏❏❏❏❏❏ [252] 17-24 ❏❏❏❏❏❏❏❏ [260] 17-24 ❏❏❏❏❏❏❏❏
[237] 25-32 ❏❏❏❏❏❏❏❏ [245] 25-32 ❏❏❏❏❏❏❏❏ [253] 25-32 ❏❏❏❏❏❏❏❏ [261] 25-32 ❏❏❏❏❏❏❏❏
[238] 33-40 ❏❏❏❏❏❏❏❏ [246] 33-40 ❏❏❏❏❏❏❏❏ [254] 33-40 ❏❏❏❏❏❏❏❏ [262] 33-40 ❏❏❏❏❏❏❏❏
[239] 41-48 ❏❏❏❏❏❏❏❏ [247] 41-48 ❏❏❏❏❏❏❏❏ [255] 41-48 ❏❏❏❏❏❏❏❏ [263] 41-48 ❏❏❏❏❏❏❏❏
[240] 49-56 ❏❏❏❏❏❏❏❏ [248] 49-56 ❏❏❏❏❏❏❏❏ [256] 49-56 ❏❏❏❏❏❏❏❏ [264] 49-56 ❏❏❏❏❏❏❏❏
[241] 57-64 ❏❏❏❏❏❏❏❏ [249] 57-64 ❏❏❏❏❏❏❏❏ [257] 57-64 ❏❏❏❏❏❏❏❏ [265] 57-64 ❏❏❏❏❏❏❏❏

Communications
[301] First Telephone Number (32 Digits)
I__D__I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[302] Second Telephone Number (32 Digits)

I__D___I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I

[303] Third Telephone Number (32 Digits)

I__D__I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____|

[304] Call Waiting Cancel String (6 Digits) - This feature is activated in [382] Option 4
I_______I_______I_______I_______I_______I_______I Default = DB70EF Program unused digits with Hex F
All six digits must be entered for changes to be saved. Fill unused digit spaces with ‘F’.

40
 Chapter 5 Programming Worksheets

Account Codes
Enter a 6-digit account number for the system account code. SIA will use this account code for all eight partitions. Only SIA supports
6-digit account codes. If the last two digits of the account code are FF, the panel will only use the first four digits.

Section [310] System Account Code [FFFFFF] I_______I_______I_______I_______I_______I_______I

Enter a four-digit account number for each active partition.

[311] Partition 1 Account Number |_______I_______I_______I_______I

[312] Partition 2 Account Number |_______I_______I_______I_______I

[313] Partition 3 Account Number |_______I_______I_______I_______I

[314] Partition 4 Account Number |_______I_______I_______I_______I

[315] Partition 5 Account Number |_______I_______I_______I_______I

[316] Partition 6 Account Number |_______I_______I_______I_______I

[317] Partition 7 Account Number |_______I_______I_______I_______I

[318] Partition 8 Account Number |_______I_______I_______I_______I

All Account Number codes are defaulted to FFFF.

Reporting Codes
[320]-[323] Alarm Reporting Codes, Zones 01-64
All Reporting Codes defaulted to FF unless otherwise indicated.
Section
[320] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I
Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[321] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I
Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[322] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I
Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[323] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I
Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[324]-[327] Alarm Restoral Reporting Codes, Zones 01-64

Section
[324] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[325] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[326] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[327] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

41
PowerSeries - PC1616/PC1832/PC1864

[328] Miscellaneous Alarm Reporting Codes

I_______I_______I Duress Alarm
I_______I_______I Opening After Alarm
I_______I_______I Recent Closing
I_______I_______I Zone Expander Supervisory Alarm
I_______I_______I Zone Expander Supervisory Restore
I_______I_______I Cross Zone Police Code Alarm
I_______I_______I Burglary Not Verified
I_______I_______I Alarm Cancelled
[329] Priority Alarm and Restoral
I_______I_______I Keypad Fire Alarm
I_______I_______I Keypad Auxiliary Alarm
I_______I_______I Keypad Panic Alarm
I_______I_______I Auxiliary Input Alarm
I_______I_______I Keypad Fire Restoral
I_______I_______I Keypad Auxiliary Restoral
I_______I_______I Keypad Panic Restoral
I_______I_______I Auxiliary Input Restore
[330]-[333] Tamper Reporting Codes, Zones 01-64
Section
[330] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[331] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[332] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[333] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[334]-[337] Tamper Restoral Reporting Codes, Zones 01-64

Section
[334] Zone 01 Zone 02 Zone 03 Zone 04 Zone 05 Zone 06 Zone 07 Zone 08
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 09 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[335] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[336] Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[337] Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

42
 Chapter 5 Programming Worksheets

[338] Miscellaneous Tamper Reporting Codes

I_______I_______I General System Tamper

I_______I_______I General System Tamper Rest.
I_______I_______I Keypad Lockout
[339]-[340] Closing (Arming) Reporting Codes, Access Codes 1-32
Section
[339] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 9 Code 10 Code 11 Code 12 Code 13 Code 14 Code 15 Code 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[340] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 25 Code 26 Code 27 Code 28 Code 29 Code 30 Code 31 Code 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[341] Miscellaneous Closing (Arming) Reporting Codes

I_______I_______I For Future Use
I_______I_______I For Future Use
I_______I_______I For Future Use
I_______I_______I For Future Use
I__0__I__0__I Automatic Zone Bypass
I_______I_______I Partial Closing
I_______I_______I Special Closing
I_______I_______I Late to Close
I_______I_______I Exit Fault
[342]-[343] Opening (Disarming) Reporting Codes, Access Codes 1-32
Section
[342] Code 1 Code 2 Code 3 Code 4 Code 5 Code 6 Code 7 Code 8
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 9 Code 10 Code 11 Code 12 Code 13 Code 14 Code 15 Code 16

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[343] Code 17 Code 18 Code 19 Code 20 Code 21 Code 22 Code 23 Code 24

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 25 Code 26 Code 27 Code 28 Code 29 Code 30 Code 31 Code 32

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[344] Miscellaneous Opening (Disarming) Reporting Codes

I_______I_______I For Future Use
I_______I_______I For Future Use
I_______I_______I For Future Use
I_______I_______I For Future Use
I_______I_______I For Future Use
I_______I_______I Auto Arm Cancellation/Postpone
I_______I_______I Special Opening

[345] Maintenance Alarm Reporting Codes [346] Maintenance Restoral Reporting Codes
I_______I_______I Battery Trouble Alarm I_______I_______I Battery Trouble Restoral
I_______I_______I AC Failure Trouble Alarm I_______I_______I AC Failure Trouble Restoral
I_______I_______I Bell Circuit Trouble Alarm I_______I_______I Bell Circuit Trouble Restoral
I_______I_______I Fire Trouble Alarm I_______I_______I Fire Trouble Restoral
I_______I_______I Auxiliary Power Supply Trouble Alarm I_______I_______I Auxiliary Power Supply Trouble Restoral
I_______I_______I TLM Trouble Code I_______I_______I TLM Restoral
I_______I_______I General System Trouble I_______I_______I General System Trouble Restoral
I_______I_______I General System Supervisory I_______I_______I General System Supervisory Restoral
I_______I_______I For Future Use I_______I_______I Cold Start

43
PowerSeries - PC1616/PC1832/PC1864

[347] Miscellaneous Maintenance Reporting Codes [348] Test Transmission Reporting Codes
I_______I_______I Telephone Number 1 FTC Restore I_______I_______I Walk Test End
I_______I_______I Telephone Number 2 FTC Restore I_______I_______I Walk Begin
I_______I_______I Event Buffer 75% Full Since Last Upload I_______I_______I Periodic Test Transmission with Trouble
I___0___I___0__I DLS Lead IN I_______I_______I Periodic Test Transmission
I___0___I___0__I DLS Lead OUT I_______I_______I System Test
I_______I_______I Zone Fault Alarm I_______I_______I For Future Use
I_______I_______I Zone Fault Restore
I_______I_______I Delinquency Code
I_______I_______I General Zone Low Battery Alarm
I_______I_______I General Zone Low Battery Restoral
I___0___I___0__I Installer Lead Out
I___0___I___0__I Installer Lead In

[349] PC5700 Maintenance Reporting Codes (only available in Canada)

I_______I_______I PC5700 Ground Fault Trouble
I_______I_______I PC5700 Ground Fault Restore
I_______I_______I PC5700 TLM Line 1 Trouble
I_______I_______I PC5700 TLM Line 1 Restore
I_______I_______I PC5700 TLM Line 2 Trouble
I_______I_______I PC5700 TLM Line 2 Restore

[350] Communicator Format Options

Default
04 I_______I_______I 1st Telephone Number
04 I_______I_______I 2nd Telephone Number
01 20 BPS, 1400 HZ handshake 05 Pager 08 10 BPS, 2300Hz handshake
02 20 BPS, 2300 HZ handshake 06 Residential Dial** 09-13 For Future Use
03 DTMF CONTACT ID 07 10 BPS, 1400Hz handshake
04 SIA FSK **Failure to communicate using Residential Dial will not generate a Failed To Communicate Trouble.

Call Direction Options

[351]-[358] Alarm/Restore Communicator Call Directions
Option 1 Option 2 Option 3 Option 4 Option 5 Options 6,7,8
Section Partition 1st Telephone 2nd Telephone Not Used Not Used Alt Comm Future Use
Number (Def ON) Number (Def OFF) (Def OFF) (Def OFF) (Def ON)
[351] 1 I________I I________I I________I I________I I________I I________I
[352] 2 I________I I________I I________I I________I I________I I________I
[353] 3 I________I I________I I________I I________I I________I I________I
[354] 4 I________I I________I I________I I________I I________I I________I
[355] 5 I________I I________I I________I I________I I________I I________I
[356] 6 I________I I________I I________I I________I I________I I________I
[357] 7 I________I I________I I________I I________I I________I I________I
[358] 8 I________I I________I I________I I________I I________I I________I

[359]-[366] Tamper/Restore Communicator Call Directions

Option 1 Option 2 Option 3 Option 4 Option 5 Options 6,7,8
Section Partition 1st Telephone 2nd Telephone Not Used Not Used Alt Comm Future Use
Number (Def ON) Number (Def OFF) (Def OFF) (Def OFF) (Def ON)
[359] 1 I________I I________I I________I I________I I________I I________I
[360] 2 I________I I________I I________I I________I I________I I________I
[361] 3 I________I I________I I________I I________I I________I I________I
[362] 4 I________I I________I I________I I________I I________I I________I
[363] 5 I________I I________I I________I I________I I________I I________I
[364] 6 I________I I________I I________I I________I I________I I________I
[365] 7 I________I I________I I________I I________I I________I I________I
[366] 8 I________I I________I I________I I________I I________I I________I

44
 Chapter 5 Programming Worksheets

[367]-[374] Opening/Closing Communicator Call Directions

Option 1 Option 2 Option 3 Option 4 Option 5 Options 6,7,8
Section Partition 1st Telephone 2nd Telephone Not Used Not Used Alt Comm Future Use
Number (Def OFF) Number (Def OFF) (Def OFF) (Def OFF) (Def OFF)

[367] 1 I________I I________I I________I I________I I________I I________I

[368] 2 I________I I________I I________I I________I I________I I________I
[369] 3 I________I I________I I________I I________I I________I I________I
[370] 4 I________I I________I I________I I________I I________I I________I
[371] 5 I________I I________I I________I I________I I________I I________I
[372] 6 I________I I________I I________I I________I I________I I________I
[373] 7 I________I I________I I________I I________I I________I I________I
[374] 8 I________I I________I I________I I________I I________I I________I

[375] System Maintenance Communicator Call Directions

Option 1 Option 2 Option 3 Option 4 Option 5 Options 6,7,8
Section Partition 1st Telephone 2nd Telephone Not Used Not Used Alt Comm Future Use
Number (Def ON) Number (Def OFF) (Def OFF) (Def OFF) (Def ON)

[375] I________I I________I I________I I________I I________I I________I

[376] System Test Transmissions Communicator Call Directions

Option 1 Option 2 Option 3 Option 4 Option 5 Options 6,7,8
Section Partition 1st Telephone 2nd Telephone Not Used Not Used Alt Comm Future Use
Number (Def ON) Number (Def OFF) (Def OFF) (Def OFF) (Def ON)

[376] I________I I________I I________I I________I I________I I________I

[377] Communication Variables

The values in gray are required for CP-01 compliant systems.
Default
003 I___0__I__0__I___1__I Swinger Shutdown (Alarms and Rest) 001-014 Transmissions; 000=disabled
003 I___0__I__0__I___3__I Swinger Shutdown (Tampers and Rest) 001-014 Transmissions; 000=disabled
003 I___0__I__0__I___3__I Swinger Shutdown (Maintenance and Rest) 001-014 Transmissions; 000=disabled
000 I___0__I__3__I___0__I Communication Delay* 000-255 seconds
030 I___0__I__3__I___0__I AC Failure Communication Delay 001-255 hours/minutes**; 000=disabled
010 I___0__I__1__I___0__I TLM Trouble Delay No. of checks required - valid entries 003 - 255
030 I___0__I__3__I___0__I Test Transmission Cycle (land line) 001-255 days/minutes***
030 I___0__I__3__I___0__I For Future Use
007 I___0__I__0__I___7__I Zone Low Battery Transmission Delay 000-255 days
030 I___0__I__3__I___0__I Delinquency Transmission Cycle 000-255 days/hours****
000 I___0__I__0__I___5__I Communications Cancelled Window 000-255 minutes

* For UL installations, the Entry Delay plus Communication Delay time must not exceed 60 seconds.
**Dependent on programming in [382], Option [6].
***Dependent on programming in [702], Option [3].
****Dependent on programming in [380], Option [8].
[378] Test Transmission Time of Day
Default
9999 I_______I_______I_______I_______I Valid entries are 0000-2359 (9999 to disable)

[379] Periodic DLS Time of Day

Default
FFFF I_______I_______I_______I_______I Valid entries are 0000-2359 (9999 for Random; FFFF to disable)

45
PowerSeries - PC1616/PC1832/PC1864

[380] First Communicator Options

Opt Def ON OFF
1 ❏ Communications Enabled ❏ Communications Disabled

2 ❏ Restorals on Bell Time-out ❏ Restorals Follow Zones

3 ❏ Pulse Dialing ❏ DTMF Dialing

4 ❏ Switch to Pulse Dialing on 5th Attempt ❏ DTMF Dial For All Attempts

5 ❏ 3rd Telephone Number Enabled ❏ 3rd Telephone Number Disabled

6 ❏ Alternate Dial (1st & 3rd) ❏ Call 1st Number, Back up to 3rd

7 ❏ For Future Use ❏

8 ❏ Delinquency Follows Zone Activity (Hours) ❏ Delinquency Follows Arming (Days)

[381] Second Communicator Options

Opt Def ON OFF
1 ❏ Open After Alarm Keypad Ringback Enabled ❏ Open After Alarm Keypad Ringback Disabled

2 ❏ Open After Alarm Bell Ringback Enabled ❏ Open After Alarm Bell Ringback Disabled

3 ❏ SIA Sends Programmed Reporting Codes ❏ SIA Sends Automatic Reporting Codes

4 ❏ Closing Confirmation Enabled ❏ Closing Confirmation Disabled

5 ❏ Talk/Listen on Phone Lines 1/3 ❏ No Talk/Listen on Phone Lines 1/3

6 ❏ Talk/Listen on Phone Line 2 ❏ No Talk/Listen on Phone Line 2

7 ❏ Contact ID Uses Programmed Reporting Codes ❏ Contact ID Uses Automatic Reporting Codes

8 ❏ ULC Communications Priority Enabled ❏ ULC Communications Priority Disabled/Standard Priority

Followed

[382] Third Communicator Options

Opt Def ON OFF
1 ❏ For Future Use ❏
2 ❏ Alarm Communications Enabled During Walk Test* ❏ Alarm Communications Disabled During Walk Test
3 ❏ Communication Cancelled Message Enabled (ON for SIA CP-01) ❏ Communication Cancelled Message Disabled
4 ❏ Call Waiting Cancel Enabled** ❏ Call Waiting Cancel Disabled
5 ❏ T-Link Interface Enabled ❏ T-Link Interface Disabled
6 ❏ AC Failure Transmission Delay is in Hours ❏ AC Failure Transmission Delay is in Minutes
7 ❏ Number of Dialing Attempt for Residential Dial is 1 ❏ Residential Dial Follows Dialing Attempts Counter
8 ❏ For Future Use ❏
*This option must remain OFF for SIA CP-01 installations.
** A Call Waiting Cancel on a non-Call Waiting line will prevent successful connection to the central station.
[383] Fourth Communicator Options

Opt Def ON OFF

1 ❏ Account Code Follows Phone Number ❏ Account Code Follows Partition

2-8 ❏ For Future Use ❏

[389] TL/GS Module Fault Check Timer
Default: 003 I_______I_______I_______I Enter no. of checks X 3 seconds - valid entries 002 to 255

46
 Chapter 5 Programming Worksheets

DLS Downloading
[401] Downloading Option Codes
Opt Def ON OFF
1 ❏ Answering Machine/Double Call enabled ❏ Answering Machine/Double Call disabled

2 ❏ User Can Enable DLS Window ❏ User Cannot Enable DLS Window

3 ❏ Call Back enabled ❏ Call Back disabled

4 ❏ User Initiated Call Up enabled ❏ User Initiated Call Up disabled

5 ❏ Auto Event Buffer Upload enabled ❏ Auto Event Buffer Upload disabled

6 ❏ 300 Baud Call Up ❏ 110 Baud Call Up

7-8 ❏ For Future Use ❏

[402] DLS Downloading Telephone Number (32 Digits)
|____D___|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|_______|

[403]-[404] DLS Downloading Access Code / Panel ID Code (Enter 6 Hexadecimal Digits)
Panel Default [403] Downloading Access Code [404] Panel ID Code

PC1616 161600 |_______|_______|_______|_______|_______|_______| |_______|_______|_______|_______|_______|_______|

PC1832 183200 |_______|_______|_______|_______|_______|_______| |_______|_______|_______|_______|_______|_______|

PC1864 186400 |_______|_______|_______|_______|_______|_______| |_______|_______|_______|_______|_______|_______|

[405] Answering Machine Double Call Timer [406] Number of Rings to Answer On
Default 060 I_______I_______I_______I (001-255 seconds) Default 000 I_______I_______I_______I (000-255 rings)
[499] Initiate PC-Link Downloading
Enter [499][Installer Code][499]

[501]- [554] Programmable Output Attributes

Program only the following attributes for the PGM options listed. All others will be ignored. PGM options are programmed in [009], [010] & [011].
PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF; Blank = Attribute not available):
Attribute: 1 2 3 4 5 6 7 8
ON Not Not True Follows Code Req. Not Not Not
used used Output Timer used used used
OFF — — Inverted On / Off No Code — — —
Req.
PGM Option
[01] Residential Burglary / Fire Bell Output Y
[02] For Future Use
[03] Sensor Reset [✱][7][2] Y
[04] 2-Wire Smoke Support (PGM2 only) Y
[05] System Armed Status Y
[06] Ready To Arm Y
[07] Keypad Buzzer Follower Mode Y
[08] Courtesy Pulse Y
[11] System Tamper (all sources) Y
[12] TLM and Alarm Y
[13] Kiss-off Output Y Y
[14] Ground Start Pulse Y Y
[15] Remote Operation (DLS Support) Y Y
[16] For Future Use Y
[17] Away Armed Status Y
[18] Stay Armed Status Y
[19] Command Output #1, [✱][7][1] Y Y Y
[20] Command Output #2, [✱][7][2] Y Y N
[21] Command Output #3, [✱][7][3] Y Y N
[22] Command Output #4, [✱][7][4] Y Y N

47
PowerSeries - PC1616/PC1832/PC1864

[23] 24-hr Silent Input (PGM2 only) Y

[24] 24-hr Audible Input (PGM2 only) Y
[25] Delayed Burglary & Fire Output Y
[26] Battery Test Output Y
[28] Holdup Output Y
[30] Partition Status Alarm Memory Output Y
[33] For Future Use
[34] Away Armed with no Zone Bypassed Status Y

Attribute:
1 2 3 4 5 6 7 8
PGM Option
ON Serv. req. AC Fail TLM Fault FTC Zone Fault Zone Tmp. Zn. Low Loss of
Bat. Clock
OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled
[09] System Trouble Y Y Y Y Y Y Y Y
ON Burg. Evnt. Fire Evnt. Panic Evnt. Med. Evnt. Supv. Evnt. Priority Holdup Follows
Evnt. Evnt. Timer*
OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Latched
[10] System Event Y Y Y Y Y Y Y N
ON Fire Alarm Panic Alarm Burglary Open/ Zone Auto Medical Police Active When
Alarm Close Bypass Alarm Code true
OFF Disabled Disabled Disabled Disabled Disabled Disabled Disabled Latched
[31] Alternate N N N N N N N N
Communicator
ON Future Use Future Use True Output Future Use Future Use Future Use Future Use AND Logic
OFF Inverted OR Logic
[29], [35]-[41] Zone Follower N N Y N N N N N
Section PGM Output 1 2 3 4 5 6 7 8
# Type*
Main Board
[501] 1 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[502] 2 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

Main Board / PC5208

[503] ** 3 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[504] ** 4 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

*Record here based on programming in [009], [010] and [011].

** These sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on the PC5208. If you use both the main
panel and the PC5208 outputs, PGM3 will work identically to the first PC5208 output, and PGM4 will work identically to the second PC5208 output.
Section PGM Output 1 2 3 4 5 6 7 8
# Type*
PC5208
[505] 5 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[506] 6 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[507] 7 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[508] 8 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[509] 9 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[510] 10 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

PC5204
[511] 11 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[512] 12 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[513] 13 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

[514] 14 ( ) I________I I________| I________| I________| I________| I________| I________| I________I

*Record here based on programming in [009], [010] and [011].

48
 Chapter 5 Programming Worksheets

PGM Output Partition Assignment

Section PGM Partition: 1 2 3 4 5 6 7 8
#
Main Board
[551] 1 I________I I________| I________| I________| I________| I________| I________| I________I

[552] 2 I________I I________| I________| I________| I________| I________| I________| I________I

Main Board / PC5208

[553] 3 I________I I________| I________| I________| I________| I________| I________| I________I

[554] 4 I________I I________| I________| I________| I________| I________| I________| I________I

PC5208
[555] 5 I________I I________| I________| I________| I________| I________| I________| I________I

[556] 6 I________I I________| I________| I________| I________| I________| I________| I________I

[557] 7 I________I I________| I________| I________| I________| I________| I________| I________I

[558] 8 I________I I________| I________| I________| I________| I________| I________| I________I

[559] 9 I________I I________| I________| I________| I________| I________| I________| I________I

[560] 10 I________I I________| I________| I________| I________| I________| I________| I________I

PC5204
[561] 11 I________I I________| I________| I________| I________| I________| I________| I________I

[562] 12 I________I I________| I________| I________| I________| I________| I________| I________I

[563] 13 I________I I________| I________| I________| I________| I________| I________| I________I

[564] 14 I________I I________| I________| I________| I________| I________| I________| I________I

Zone Follower PGM Zone Assignment

If a Zone Follower PGM type 29, 35-41 is used, the PGM Output Partition Assignment will be treated as a PGM Output Zone Assign-
ment. Each Zone Follower PGM applies to a different bank of zones, as in the following table. Record the assignments above.
Option: 1 2 3 4 5 6 7 8

[29] Zone Follower (1-8) Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
[35] Zone Follower (9-16) Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16
[36] Zone Follower (17-24) Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24
[37] Zone Follower (25-32) Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32
[38] Zone Follower (33-40) Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 Zone 38 Zone 39 Zone 40
[39] Zone Follower (41-48) Zone 41 Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48
[40] Zone Follower (49-56) Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56
[41] Zone Follower (57-64) Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64

Extended Reporting Codes

[601]-[604] Closing (Arming) Reporting Codes, Access Codes 33-95
Section
[601] Code 33 Code 34 Code 35 Code 36 Code 37 Code 38 Code 39 Code 40
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 41 Code 42 Code 43 Code 44 Code 45 Code 46 Code 47 Code 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[602] Code 49 Code 50 Code 51 Code 52 Code 53 Code 54 Code 55 Code 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 57 Code 58 Code 59 Code 60 Code 61 Code 62 Code 63 Code 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[603] Code 65 Code 66 Code 67 Code 68 Code 69 Code 70 Code 71 Code 72

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 73 Code 74 Code 75 Code 76 Code 77 Code 78 Code 79 Code 80

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[604] Code 81 Code 82 Code 83 Code 84 Code 85 Code 86 Code 87 Code 88

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 89 Code 90 Code 91 Code 92 Code 93 Code 94 Code 95

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

49
PowerSeries - PC1616/PC1832/PC1864

[605]-[608] Opening (Disarming) Reporting Codes, Access Codes 33-95

Section
[605] Code 33 Code 34 Code 35 Code 36 Code 37 Code 38 Code 39 Code 40
I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 41 Code 42 Code 43 Code 44 Code 45 Code 46 Code 47 Code 48

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[606] Code 49 Code 50 Code 51 Code 52 Code 53 Code 54 Code 55 Code 56

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 57 Code 58 Code 59 Code 60 Code 61 Code 62 Code 63 Code 64

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[607] Code 65 Code 66 Code 67 Code 68 Code 69 Code 70 Code 71 Code 72

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 73 Code 74 Code 75 Code 76 Code 77 Code 78 Code 79 Code 80

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

[608] Code 81 Code 82 Code 83 Code 84 Code 85 Code 86 Code 87 Code 88

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Code 89 Code 90 Code 91 Code 92 Code 93 Code 94 Code 95

I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I I_______I_______I

Automatic Disarming Schedule

Enter a four-digit number (HH:MM) for each day that the system will auto-disarm for each partition ([681] for Partition 1 through [688] for Partition
8). Valid entries are 0000-2359. All entries are disabled (9999) by default.
Sunday Monday Tuesday Wednesday Thursday Friday Saturday
[681]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[682]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[683]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[684]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[685]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[686]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[687]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I
[688]I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I I_______I_______I:I_______I_______I

Auto-Disarm Holiday Schedule

Enter a six-digit number (MM:DD:YY) for each day that the system will skip auto-disarm for each partition ([691] for Partition 1 through [698] for
Partition 8). Program [99][99][99] to disable Auto-Disarm schedule. All entries are disabled by default.
[691] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7
I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

[692] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

[693] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

[694] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

50
 Chapter 5 Programming Worksheets

[695] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

[696] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

[697] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

[698] Holiday 1 Holiday 2 Holiday 3 Holiday 4 Holiday 5 Holiday 6 Holiday 7

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

Holiday 8 Holiday 9 Holiday 10 Holiday 11 Holiday 12 Holiday 13 Holiday 14

I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I I____I_____II_____I_____II_____I_____I

INTERNATIONAL PROGRAMMING
[700] Automatic Clock Adjust
Default = 60 |________|_________| Valid Entries 00-99 Seconds
[701] First International Options
Opt Def ON OFF
1 ❏ 50 Hz AC ❏ 60 Hz AC

2 ❏ Time Base - Internal Crystal ❏ Time Base - AC Line

3 ❏ AC/DC Arming Inhibit Enabled ❏ AC/DC Arming Inhibit Disabled

4 ❏ All System Tampers Require Installer Reset ❏ All System Tampers Follow Restore

5 ❏ 6-digit User Access Codes ❏ 4-digit User Access Codes

6 ❏ Busy Tone Detection Enabled ❏ Busy Tone Detection Disabled

7 ❏ High Current Battery Charge ❏ Standard Current Battery Discharge

8 ❏ DLS/Audio has no priority ❏ DLS/Audio has priority

[702] Second International Options

Opt Def ON OFF
1 ❏ Pulse Dialing Make/Break Ratio is 33/67 ❏ Pulse Dialing Make/Break Ratio is 40/60

2 ❏ Force Dialing Enabled ❏ Force Dialing Disabled

3 ❏ Land Line Test Transmission in Minutes ❏ Land Line Test Transmission in Days

4 ❏ 1600 Hz Handshake ❏ Standard Handshake

5 ❏ ID Tone Enabled ❏ ID Tone Disabled

6 ❏ 2100 Hz ID Tone ❏ 1300 Hz ID Tone

7 ❏ One-Time 1-hr User Enabled DLS Window ❏ Full 6-hr User Enabled DLS Window

8 ❏ Bell on FTC when Armed ❏ FTC Trouble only when Armed

[703] Delay Between Dialing Attempts

Default = 003 |________|_________|_________| Valid Entries 000-255 sec.

51
PowerSeries - PC1616/PC1832/PC1864

Module Programming
[801] PC5400 Printer Module Programming
Refer to the PC5400 Installation Manual for installation and programming instructions.
[802] PC59xx VOX Module Programming
Refer to the PC59xx Installation Manual for installation and programming instructions.
[804] Wireless Expansion Programming
Refer to the RF5132/RFK55xx Installation Manual for programming locations and instructions.
[805] PC5100 Programming
Refer to the PC5100 Installation Manual for programming locations and instructions.
[851] TL/GS Module Programming
Refer to the TL/GS Installation Manual for programming locations and instructions.
Special Installer Functions
[898] Wireless Enrollment

[899] Template Programming

[900] Panel Version Displayed
[901] Installer Walk Test Mode Enable/Disable
[902] Module Supervision Reset
[903] Module Supervision Field
[904] Wireless Module Placement Test
[905] - [909] For Future Use
[989] Default Master Code
[990][Installer Code][990] Installer Lockout Enable
[991][Installer Code][991] Installer Lockout Disable
[992] For Future Use
[993][Installer Code][993] Restore Alternate Communicator to Default Programming
[994] For Future Use
[995][Installer Code][995] Restore Escort5580 to Default Programming
[996][Installer Code][996] Restore RF5132 to Default Programming
[997][Installer Code][997] Restore PC5400 to Default Programming
[998][Installer Code][998] Restore PC59xx to Default Programming
[999][Installer Code][999] Restore Control Panel to Default Programming

52
 Chapter 5 Programming Worksheets

For the Record

Customer: ___________________________________________________________________________________________________________

Address: ____________________________________________________________________________________________________________

Telephone: ______________________________________________ Installation Date: ___________________________________________

Installer’s Code: _____________________________________________________________________________________________________

Module Name Description Location

PC1616/PC1832/PC1864 Main Panel I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
I________________________________I I____________________I I_____________________________________________________________________________________________I
Keypads Keypad Type Location
Keypad 1 I____________________I I_____________________________________________________________________________________________I
Keypad 2 I____________________I I_____________________________________________________________________________________________I
Keypad 3 I____________________I I_____________________________________________________________________________________________I
Keypad 4 I____________________I I_____________________________________________________________________________________________I
Keypad 5 I____________________I I_____________________________________________________________________________________________I
Keypad 6 I____________________I I_____________________________________________________________________________________________I
Keypad 7 I____________________I I_____________________________________________________________________________________________I
Keypad 8 I____________________I I_____________________________________________________________________________________________I

53
PowerSeries - PC1616/PC1832/PC1864

Zone Programming Summary

Zone programming can be found in sections [001] - [004], [101] - [164], [020], [202] - [265]. Use this area to record a summary of
your zone programming.
System Zone System Zone
Zone Zone Label Type Zone Zone Label Type

Zone 1 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 33 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 2 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 34 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 3 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 35 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 4 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 36 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 5 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 37 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 6 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 38 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 7 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 39 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 8 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 40 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 9 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 41 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 10 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 42 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 11 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 43 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 12 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 44 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 13 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 45 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 14 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 46 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 15 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 47 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 16 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 48 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 17 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 49 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 18 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 50 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 19 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 51 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 20 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 52 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 21 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 53 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 22 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 54 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 23 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 55 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 24 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 56 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 25 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 57 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 26 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 58 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 27 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 59 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 28 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 60 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 29 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 61 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 30 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 62 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 31 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 63 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

Zone 32 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I Zone 64 I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I I_____I_____I

54
 Appendix A: Reporting Codes

Appendix A: Reporting Codes

The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on reporting code formats and notes
about individual reporting codes, see programming sections [320]-[349] and [601]-[608].
Contact ID
The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to indicate specific information
about the signal. For example, if zone 1 is an entry/exit point, you could program the event code as [34]. The central station would receive the fol-
lowing: *BURG - ENTRY/EXIT - 1 where the “1” indicates which zone went into alarm.
SIA Format - Level 2 (hard coded)
The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - October
1997. This format will send the Account Code along with its data transmission. The transmission will look similar to the following at the receiver:
NOTE: A system event will use the Area Identifier Ri00.
N Ri01 = BA 01 BA = Burglary Alarm
N = New Event 01 = Zone 1
Ri01 = Partition /Area Identifier

Table 1: Reporting Codes/

Automatic
Dialer SIA Auto
Section # Reporting Code Code Sent When... Contact ID
Direction* Rep Codes**
Codes
[320]-[323] Zone Alarms Zone goes into alarm A/R See
See Table 3
[324]-[327] Zone Restorals Alarm condition has been restored A/R Tables 2 & 3
[328] Duress Alarm Duress code entered at keypad A/R E(1)21-000 HA-00
[328] Opening After Alarm System disarmed with alarm in memory A/R E(4)58-000 OR-00
[328] Recent Closing Alarm occurs within two minutes of system arming A/R E(4)59-UUU CR-00
[328] Zone Expander Supervisory Panel loses/restores supervisory transmission over the Keybus from A/R E(1)43-000/ UA-00/UH-00
Alarm/Rest. zone expansion modules, or keypads with zone inputs R(1)43-000
[328] Cross Zone (Police Code) Two zones on the same partition go into alarm during any given A/R E(1)39-000 BM-00/BV-00
Alarm armed-to-armed period (incl. 24Hr zones)
[328] Burglary Not Verified This event is transmitted when a second cross-zone alarm does not A/R E(3)78-000 BG-00
occur within the cross-zoning time
[328] Alarm Cancelled Sent when the system is disarmed after an alarm, but before the A/R E(4)A6-UUU BC-00
expiry of the alarm cancellation timer
[329] [F] Key Alarm/Restoral Keypad fire alarm/restore (alarm and restore rep. codes sent A/R E(1)1A-000/ FA-00/FH-00
together) R(1)1A-000
[329] [A] Key Alarm/Restoral Keypad auxiliary alarm/restore (alarm and restore rep. codes sent A/R E(1)AA-000/ MA-00/MH-00
together) R(1)AA-000
[329] [P] Key Alarm/Restoral Keypad panic alarm/restore (alarm and restore rep. codes sent A/R E(1)2A-000/ PA-00/PH-00
together) R(1)2A-000
[329] Aux Input Alarm/Rest Option#23/24: a panic button wired to PGM 2 is pressed/access code A/R E(1)4A-000/ UA-99/UH-99
is entered A/R R(1)4A-000 FA-99/FH-99
Option #04: a 2-wire smoke detector wired to PGM 2 goes into alarm/ E(1)11-000/
alarm is cleared. R(1)11-000
[330]-[337] Zone Tamper/Restoral Zone is tampered / tamper condition restored T/R E(3)83-ZZZ/ TA-ZZ/TR-ZZ
R(3)83-ZZZ
[338] General System Tamper/ Enrolled module with tamper inputs has a tamper alarm/all module T/R E(1)45-000/ ES-00/EJ-00
Rest. tampers restored R(1)45-000
[338] Keypad Lockout Max. number of incorrect access codes has been entered at a T/R E(4)61-000 JA-00
keypad
[339-341] Closings System armed (user 01-32 indicated) O/C R(4)A1-UUU CL-UU
[341] Partial Closing One or more zones bypassed when system armed O/C E(4)56-000 CG-00
[341] Special Closing Closing (arming) using one of the following methods: quick arm, auto O/C R(4)AA-000 CL-00
arm, keyswitch, function key, maintenance code, DLS software,
wireless key
[341] Late to Close Whenever the Auto-arm prealert sounds (if the Late to Close option is enabled) O/C R(4)54-000 CI-00
[341] Exit Fault The Exit Fault pre-alert occurs and Entry Delay expires O/C E(3)74-ZZZ EE-00
[341] Zone Bypass Zone is bypassed O/C E(5)7A-ZZZ UB-ZZ
[342-344] Openings System disarmed (user 01-32 indicated) O/C E(4)A1-UUU OP-UU
[344] Auto-arm Cancellation Auto-arm cancelled O/C E(4)55-000 CI-00
[344] Special Opening Opening (disarming) using one of the following methods: keyswitch, O/C E(4)AA-000 OP-00
maintenance code, DLS software, wireless key
[345]-[346] Battery Trouble/Rest. PC1616/PC1832/PC1864 battery is low/battery restored MA/R E(3)A2-000/ YT-00/YR-00
R(3)A2-000
[345]-[346] AC Line Trouble/Rest. AC power to control panel is disconnected or interrupted/AC power MA/R E(3)A1-000/ AT-00/AR-00
restored (Both codes follow AC Failure Comm. Delay.) R(3)A1-000
[345]-[346] Bell Circuit Trouble/Rest. Open or short circuit detected across bell terminals/bell circuit MA/R E(3)21-000/ YA-99/YH-99
restored R(3)21-000
[345]-[346] Fire Trouble/Rest. Trouble occurs/restores on a fire zone MA/R E(3)73-000/ FT-99/FJ-99
R(3)73-000
[345]-[346] Auxiliary Power Trouble/Rest. Aux voltage supply trouble/restoral MA/R E(3)12-000/ YP-00/YQ-00
R(3)12-000

55
PowerSeries - PC1616/PC1832/PC1864

Automatic
Dialer SIA Auto
Section # Reporting Code Code Sent When... Contact ID
Direction* Rep Codes**
Codes
[345]-[346] TLM Failure/Restore Telephone line monitoring trouble/Telephone line restored MA/R E(3)51-000/ LT-01/LR-01
R(3)51-000
[345]-[346] Gen System Trouble/Rest. “Service Required” trouble (view troubles using [*][2])/trouble MA/R E(3)AA-000/ YX-00/YZ-00
restored R(3)AA-000
[345]-[346] Gen System Supervisory Control panel loses/restores communications with module(s) MA/R E(3)3A-000/ ET-00/ER-00
Trouble/Rest. connected to the Keybus R(3)3A-000
[346] Cold Start (System Reset) The system has been restarted after a total power loss. The reporting MA/R R(3)A5-000 RR-00
code is sent after a 2 minute start-up delay
[347] Phone# 1 or 2 FTC Restoral Control panel has restored communications to central station on MA/R R(3)54-000 YK-00
Phone# 1 or 2 (after FTC)
[347] Event Buffer is 75% Full Event buffer is almost full since last upload MA/R E(6)22-000 JL-00
[347] DLS Lead In Downloading session start MA/R E(4)11-000 RB-00
[347] DLS Lead Out Downloading session complete MA/R E(4)12-000 RS-00
[347] Zone Fault/Rest. One or more zones have faults/restored MA/R E(3)8A-ZZZ/ UT-ZZ/UJ-ZZ
R(3)8A-ZZZ
[347] Delinquency Programmed amount of time (days or hours) for delinquency has MA/R E(6)54-000*** CD-00
expired without zone activity, or without system being armed
[347] Wireless Device Low Battery Wireless zones, panic pendants, handheld keypads, wireless keys MA/R E(3)84-000/ XT-00/XR-00
Trouble/Rest. have low battery/all low batteries restored R(3)84-000 XT-ZZ/XR-ZZ****
[347] Installer Lead In/Lead Out Installer’s mode has been entered/exited MA/R E(6)27-000/ LB-00/LS-00
E(6)28-000
[348] Walk Test End/Begin End of test/Beginning of test T R(6)A7-UUU/ TE-00/TS-00
E(6)A7-UUU
[348] Periodic Test with Trouble Periodic system test transmission with trouble T E(6)A8-000 RY-00
[348] Periodic Test Periodic system test transmission T E(6)A2-000 RP-00
[348] System Test [*][6] bell/communications test T E(6)A1-000 RX-00
[349] PC5700 Ground Fault Trouble/ Ground/Fault/Trouble occurs on the PC5700 MA/R E(3)1A-000 US-00/UR-00
Rest
[349] PC5700 TLM Line 1 Trouble/Rest. TLM Trouble /Restore occurs on the PC5700 MA/R E(3)51-000/ LT-01/LR-01
R(3)51-000
[349] PC5700 TLM Line 2 Trouble/Rest. TLM Trouble /Restore occurs on the PC5700 MA/R E(3)52-000/ LT-02/LR-02
R(3)52-000
[601]-[604] Closings System armed (user 33-95 indicated) O/C R(4)A1-UUU CL-UU
[605]-[608] Openings System disarmed (user 33-95 indicated) O/C E(4)A1-UUU OP-UU
* A/R = alarms/restorals; T/R = tampers/restorals; O/C = openings/closings; MA/R = miscellaneous alarms/restorals; T = test transmissions
** UU = user number (User 01-95); ZZ = zone number (01-64)
*** Use the “Fail to close” event code [(4)54] to report closing or activity delinquency. Ensure the central station is aware that this code is used.
**** Zones are identified, panic pendants, wireless keys, and handheld keypads are not.

Table 2: Contact ID Programmed Zone Alarm/Restoral Event Codes Table 3: Automatic Zone Alarm/Restoral Codes
(as per SIA DCS: ‘Contact ID’ 01-1999): Program any of these codes for zone
alarms/restorals when using the standard (non-automatic) Contact ID reporting Zone Definition SIA Auto Rep Contact ID Contact ID
format. Codes* Alarm Auto Rest. Auto
Rep Codes* Rep Codes
Medical Alarms (1)34 Entry / Exit Delay 1 BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
(1)AA Medical (1)35 Day / Night Delay 2 BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
(1)A1 Pendant Transmitter (1)36 Outdoor Instant BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
Interior BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
(1)A2 Fail to Report In (1)37 Tamper
Interior Stay/Away BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
Fire Alarms (1)38 Near Alarm Delay Stay/Away BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
Delayed 24-Hr Fire FA-ZZ/FH-ZZ E(1)1A-ZZZ R(1)1A-ZZZ
(1)1A Fire Alarm General Alarms Standard 24-Hr Fire FA-ZZ/FH-ZZ E(1)1A-ZZZ R(1)1A-ZZZ
(1)11 Smoke (1)4A General Alarm 24-Hr Supervisory US-ZZ/UR-ZZ E(1)5A-ZZZ R(1)5A-ZZZ
(1)12 Combustion (1)43 Exp. module failure 24-Hr Supervisory Buzzer UA-ZZ/UH-ZZ E(1)5A-ZZZ R(1)5A-ZZZ
(1)13 Water Flow (1)44 Sensor tamper 24-Hr Burglary BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
24-Hr Holdup HA-ZZ/HH-ZZ E(1)22-ZZZ R(1)22-ZZZ
(1)14 Heat (1)45 Module Tamper
24-Hr Gas GA-ZZ/GH-ZZ E(1)51-ZZZ R(1)51-ZZZ
(1)15 Pull Station (1)4A Cross Zone Police Code 24-Hr Heat KA-ZZ/KH-ZZ E(1)58-ZZZ R(1)58-ZZZ
(1)16 Duct 24 Hour Non-Burglary 24-Hr Auxiliary (Medical) MA-ZZ/MH-ZZ E(1)AA-ZZZ R(1)AA-ZZZ
24-Hr Panic PA-ZZ/PH-ZZ E(1)2A-ZZZ R(1)2A-ZZZ
(1)17 Flame (1)5A 24 Hour non-Burg
24-Hr Emerg. (non-medical) QA-ZZ/QH-ZZ E(1)A1-ZZZ R(1)A1-ZZZ
(1)18 Near Alarm (1)51 Gas detected
24-Hr Sprinkler SA-ZZ/SH-ZZ E(1)13-ZZZ R(1)13-ZZZ
Panic Alarms (1)52 Refrigeration 24-Hr Water WA-ZZ/WH-ZZ E(1)54-ZZZ R(1)54-ZZZ
24-Hr Freeze ZA-ZZ/ZH-ZZ E(1)59-ZZZ R(1)59-ZZZ
(1)2A Panic (1)53 Loss of Heat
24-Hr Latching UA-ZZ/UH-ZZ E(1)4A-ZZZ R(1)4A-ZZZ
(1)21 Duress (1)54 Water Leakage Interior Delay BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
(1)22 Silent (1)55 Foil Break Auto Verified Fire FA-ZZ/FH-ZZ E(1)1A-ZZZ R(1)1A-ZZZ
(1)23 Audible (1)56 Day Trouble 24-Hr Fire Supervisory FS-ZZ/FV-ZZ E(2)AA-ZZZ R(2)AA-ZZZ
Burglar Alarms (1)57 Low bottled Gas level Day Zone BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
Instant Stay/Away BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
(1)3A Burglary (1)58 High Temp 24-Hr Bell/Buzzer UA-ZZ/UH-ZZ E(1)5A-ZZZ R(1)5A-ZZZ
(1)31 Perimeter (1)59 Low Temp 24-Hr Non-latching Tamper UA-ZZ/UH-ZZ E(1)4A-ZZZ R(1)4A-ZZZ
(1)32 Interior (1)61 Loss of Air Flow Night Zone BA-ZZ/BH-ZZ E(1)3A-ZZZ R(1)3A-ZZZ
(1)33 24 Hour Delayed 24-Hr Fire (Wireless) FA-ZZ/FH-ZZ E(1)1A-ZZZ R(1)1A-ZZZ
Standard 24-Hr Fire(Wireless) FA-ZZ/FH-ZZ E(1)1A-ZZZ R(1)1A-ZZZ
24-Hr CO Alarm GA-ZZ/GH-ZZ E(1)62-ZZZ R(1)62-ZZZ
* ZZ or ZZZ= zones 01-64

56
 Appendix B: UL Listed Commercial and Residential Installations

Appendix B: UL Listed Commercial and Residential Installations

The control panel model PC1616/PC1832/PC1864 has been tested and found in com- ULC Central Station Fire and Burglary Monitoring Installations
pliance with the following standard: • For installation requirements, levels of security, communication modules and configura-
UL1610 Central-Station Burglar-Alarm Units tions (Refer to the ULC Installation Information Sheet, DSC #29002157)
UL365 Police Station Connected Burglar Alarm Units and Systems • Use a CSA/cUL approved transformer (hardwired connections required for Fire Moni-
toring)
UL1023 Household Burglar-Alarm System Units • All tamper circuits may be connected to the same zone
UL985 Household Fire Warning System Units
Programming
UL1635 Digital Alarm Communicator System Units The notes in the programming sections describing the system configurations for UL/ULC
ULC-S304-06 Signal Receiving Centre & Premise Burglar Alarm Control Units listed installations shall be implemented
ULC-S559-04 Equipment for Fire Signal Receiving Centres and Systems Control of the Protected Premises
ULC-S545-02 Residential Fire Warning System Control Units In order to have a UL certificated system the protected are is to be under the responsibility
ORD-C1023-1974 Household Burglar-Alarm System Units of one ownership and management (i.e., one business under one name). This may be a
This product has also been tested and found in compliance with the ANSI/SIA CP- group of buildings attached or unattached with different addresses but under the responsi-
01-2000 Control Panel Standard - Features for False Alarm Reduction bility of someone having mutual interest. The person of the mutual interest is not the
This product is UL/ULC listed under the following categories: alarm-installing company.
AMCX/AMCXC Central Stations Alarm Units Bell Location
APAW Police-station-connected Alarm Units The alarm sounding device (bell) shall be located where it can be heard by the person
DAYRC Central Station Fire Alarm System Units operating the security system during the daily arming and disarming cycle.
UTOU/UTOUC Control Units and Accessories, Household System Type Protection of the Control Unit
NBSX/NBSXC Household Burglar Alarm System Units The local control unit and the local power supply must be protected in one of the follow-
AMTB Control Panels, SIA False Alarm Reduction ing ways:
The product is labeled with the UL and ULC listing marks along with the SIA CP-01 com- • The control unit and audible alarm device must be in a protected area which is armed 24
pliance statement (Also Classified in accordance with SIA-CP-01 Standard) as proof of hours a day.
compliance with the above mentioned standards. For further information on this product's • Each partition must arm the area protecting the control unit and the audible alarm device
listings please also refer to the official listing guides published at the UL web site power supply. This may require duplicate protection armed by each partition. Access to
this protected area, without causing and alarm, will require that all partitions be dis-
(www.ul.com) under Certifications Section or ULC web site (www.ulc.ca) under Online armed.
Directories. • In all cases described above, the protected area for the control unit must be programmed
UL/ULC Installations Required Programming Options as not-bypassable.
• All burglary-type zones shall be configured with SEOL or DEOL configuration (refer to Casual Users
section [013], option 1 shall be OFF) The installer should caution the user(s) not to give system information (e.g. codes, bypass
• Use at least one Smoke Detector for Fire Installations (refer to section [001], fire zone
shall be programmed as type 08 (hardwired) or 88 (wireless)) methods, etc.) to casual users (baby-sitters or service people). Only the One-Time Use
• The entry delay shall not exceed 60 seconds (refer to section [005]) codes shall be given to casual users.
• The exit delay shall not exceed 120 seconds (refer to section [005]) User Information
• The minimum Bell Time-out is 4 minutes (refer to section [005]) The installer should advise the users and note in the User's Manual:
For ULC Residential Fire Installations the minimum Bell Time-out is 5 min. • Service organization name and telephone number
For UL Home Health Care Installations the minimum Bell Time-out is 5 min. • The programmed exit time
For UL Commercial Burglary Installations minimum Bell Time-out is 15 min. • The programmed entry time
• Temporal Three Fire Signal shall be enabled (Section [013], option 8 shall be ON) • Test system weekly
• Arm/Disarm Bell Squawk shall be enabled when using wireless key WS4939 (refer to • The installer's code cannot arm or disarm the system
section [014], option 1 shall be ON) SIA False Alarm Reduction Installations
• A code will be required for bypassing (Section [015], option 5 shall be ON) Minimum required system consists of one Control unit model PC1864 or PC1832 or
• Trouble beeps shall be enabled (Section [023], option 7 shall be ON) PC1616 and any one of the compatible listed keypads: PK5500, PK5501, PK5508,
• AC trouble indication LED shall be enabled (refer to Keypad Programming, section PK5516, PKP-LCD, PKP-ICN. For a list of the defaults value programmed when the unit
[075], options 5 and 6 shall be ON ) is shipped from the factory and for any other programming information refer to Appendix
• DACT Communicator shall be enabled for Supervising Station Monitoring (refer to sec- C: False Alarm Reduction.
tion [380], option 1 shall be ON). The following optional subassembly modules also bear the SIA CP-01-2000 classification
The DACT communicator for this product has no line security. and may be used if desired: PC5108 Zone Expander, PC5208 PGM Output Module,
• Telephone Line Monitoring (TLM) shall be enabled (refer to section [015], option 7 shall PC5204 Auxiliary Power Supply and PC5400 Serial Output Module.
be ON)
CAUTION
The product shall be programmed to perform 5 (min.) to 10 (max.) attemptsfor com- • For SIA FAR installations use only modules/devices that are listed on this page
munication of an event to the supervising station. If unsuccessful, a Fail To Commu- • Fire Alarm Verification feature (Auto Verified Fire Zone type [29]) is not supported on
nicate (FTC) trouble is generated. 2-wire smoke detectors zones. This feature may be enabled for 4-wire smoke detectors
• Test transmission cycle shall be set for monthly transmission (see Section [377]) only . The fire alarm delay is 60s.
For ULC Residential/Commercial installations set for daily test transmission • Call Waiting Cancel (Section [382], Option 4) feature on a non-Call Waiting line will
UL Central Station and Police Connect with Standard or Encrypted Line Security prevent successful communication to the supervising station.
Service • All smoke detectors on the system must be tested annually by conducting the Installer
• The installation must use the T-Link TL250 or T-Link TL300 Internet/Intranet communi- Walk Test. Prior to exiting the walk test mode, a sensor reset must be conducted on the
cator which communicates over LAN/WAN/Internet to the SG-System II or SG-System system, [*][7][2] to reset all latching 4-wire smoke detectors. Please refer to the smoke
II receivers. detector installation instructions on how to correctly test the detectors.
• Polling time shall be 200 seconds and compromise detection time shall be 6 min. NOTES
• For Encrypted line security applications, the T-Link TL250 or TL300 shall have the • Programming at installation may be subordinate to other UL requirements for the
Encryption Key enabled (AES128 bit encryption algorithm is validated under NIST Cer- intended application
tificate No. 109). • Cross zones have the ability to individually protect the intended area (e.g. motion detec-
UL Local, Central Station and Police Connect with No Line Security Service tors which overlap)
• The installation shall use a Bell which is UL Listed for Mercantile local alarms (i.e. • Cross zoning is not recommended for line security Installations nor is to be implemented
AMSECO MBL10B with model AB-12 bell housing. on exit/entry zones.
• The digital communicator shall be enabled • There is a communication delay of 30 seconds in this control panel. It can be removed, or
• The control panel shall be in the attack resistant enclosure DSC Model CMC-1 or it can be increased up to 45 seconds at the option of the end user by consulting with the
PC4050CAR installer.
• Do not duplicate any reporting codes. This applies for all communication formats other
UL Home Health Care Signaling Equipment than SIA or CID sending automatic programmed reporting codes.
• There must be at least two keypads, one of either one of the compatible keypads models • The security system shall be installed with the sounding device activated and the com-
PK5500, PK5501, PK5508, PK5516 municator enabled for transmission using SIA or CID format.
• Each system shall be programmed to activate an audible Trouble signal within 90 sec-
onds upon loss of microprocessor memory

57
PowerSeries - PC1616/PC1832/PC1864

Appendix C: SIA False Alarm Reduction

SIA Feature
Comments Range/Default Requirement
Programming Section

Exit Time - [005], 3rd entry Access to Entry and Exit delays for each partition and Bell Time Out for the system For Full or auto arming: Required
Range: 45-255 seconds (programmable)
Default: 60 sec.

Progress Annunciation/ Enables audible exit beeps from the keypad for the duration of exit delay Individual keypads Allowed
Disable - for Silent Exit - may be disabled
[014], Option 6 ON Default: All Enabled

Exit Time Restart - Enables the exit delay restart feature Default: Enabled Required
[018], Option 7 ON

Auto Stay Arm on Unvacated Function Key: Stay Arming. All Stay/Away type zones (05, 06) will be automatically If no exit after full arm Required
Premises - [001]-[004] Zone bypassed Default: Enabled
type 05, 06

Exit Time and Progress System Times and Audible Exit beeps can be disabled when using the Key fob to Default: Enabled Allowed
Annunciation/Disable arm away the system
or Remote Arming -
[005] and [014] bit 6

Entry Delay(s) - [005], 1st and Access to Entry and Exit delays for each partition and Bell Time Out for the system. Range: 30 sec. to 4 min. Required
2nd entry NOTE: Combined Entry delay and Communications Delay (Abort Window) shall not Default: 30 sec. (programmable)
exceed 60s

Abort Window for Non-Fire Access to zone attributes, i.e, swinger shutdown, transmission delay and cross May be disabled Required
zones - [101]-[164] bit 7 ON zone. Individual zones attribute bit 7 (Transmission delay) is by default ON by zone or zone type
Default: Enabled

Abort Window - for Non-Fire Access to the programmable delay before communicating alarms. NOTE: Com- Range: 15 - 45 sec. Required
zones - [377], 4th entry bined Entry delay and Communications Delay (Abort Window) shall not exceed 60s Default: 30 sec. (programmable)

Abort Annunciation - [382], Enables the “Communication Cancelled” message display on all keypads Annunciate that no Required
Option 3 ON alarm was transmitted
Default: Enabled

Cancel Annunciation - [328], Access to the reporting code for Alarm Cancelled Annunciate that a Required
8th entry Cancel was transmitted
Default: Enabled

Duress Feature - [✱][5] Master Do not derive code from an existing Master/User code (e.g., Master code is 1234, No 1+/- derivative of another Allowed
Code - [99] Option 2 ON the duress code should not be 1233 or 1235) user code. No duplicates with
other user codes
Default: disabled

Cross Zoning - [018] This option enables Cross Zoning for entire system. Individual zones can be ena- Programming required Required
Option 6 ON bled for Cross zoning via Zone attribute bit 9 in sections [101] - [164] Default: Disabled
[101]-[164] bit 9 OFF

Cross Zone Timer - [176] Access to the programmable Cross Zone timer May program Allowed
Range: 001-255 sec.
Default: 60 secs

Swinger Shutdown for Alarms Access to the swinger shutdown limit for zone alarms For all non-fire zones Required
[377] 1st entry shut down at 1 or 2 trips (programmable)
Default: 1 Trip

Swinger Shutdown Disable - Access to zone attributes, i.e., swinger shutdown, transmission delay and cross For non-police Allowed
[101] - [164] bit 6 ON zone. Individual zones attribute bit 6 (Swinger shutdown enabled) is by default ON response zones
Default: Enabled

Fire Alarm Verification - Auto Verified Fire, use only with 4 wire type detectors that can be reset by the panel 70 seconds reset and Required
Zone Type [29] 4-wire smoke detector powered from AUX + and PGM1 - PGM4 (type 03, Sensor confirmation time
reset) Default: disabled

Call Waiting Cancel Dial String - Access to the dialing sequence used to disable call waiting Dependant on user phone line Required
[304], [382], Opt. 4 OFF Default: disabled

Testing

System Test: [✱][6] Master The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on.
Code, Option 4 Refer to the User Manual (part no. 29008261).

Installer Walk Test Mode: [901] This mode is used to test each zone on the system for proper functionality.

Alarm Communications Enables Communication of zone alarms while installer Walk Test is active.
During Walk Test [382] Opt. 2

Walk Test End and Begin Access to the reporting codes for Walk Test Begin and Walk Test End.
Reporting Codes [348], 1st and
2nd Entries

58
 Appendix D: Troubleshooting Guide

Appendix D: Troubleshooting Guide

Testing:

• Power up system
• Program options as required (See Programming Section)
• Violate, then restore zones
• Verify correct Reporting Codes are sent to the Central Station

Troubleshooting:

LCD Programmable-Message Keypad

• Press [✱][2] to view a trouble condition.
• The trouble light will flash and the LCD will display the first trouble condition present.
• Use the arrow keys to scroll through all trouble conditions present.

NOTE: When additional information is available for a specific trouble condition a [✱] will appear on the display.
Press the [✱] key to view the additional information
LED Keypads, LCD Fixed Message Keypads
• Press [✱][2] to view a trouble condition.
• The trouble light will flash.
• Refer to the Trouble Summary chart below to determine the trouble condition(s) present.

Trouble Summary:

Light [1][✱] Service Required - Press [1] for more information

[1] Low Battery
[2] Bell Circuit
[3] General System Trouble
[4] General system Tamper
[5] Module Supervision
[6] RF Jam Detected
[7] PC5204 Low Battery
[8] PC5204 AC Failure

Light [2] AC Trouble

Light [3] Telephone Line Trouble

Light [4] Failure to Communicate

Light [5][✱] Zone Fault -Press [5] for more information

Light [6][✱] Zone Tamper - Press [6] for more information

Light [7][✱] Wireless Device Low Battery - Press [7] for more information

Light [8] Loss of Time or Date

59
PowerSeries - PC1616/PC1832/PC1864

Trouble Cause Troubleshooting

rouble 1 Ser ice e uired Press 1 to determine speci ic trouble

[1] Low Battery Main panel battery less t an 11.1 DC NOTE: If battery is new allow 1 hour for battery to charge.
eri y oltage measured across AC terminals is 16-1 AC.
NOTE: This trouble condition will not eplace trans ormer i re uired
clear until the battery voltage is Disconnect battery wire leads
12.5VDC min., under load. - eri y battery c arging oltage measured across battery leads
1 .70 - 1 . 0 DC.
Connect battery remo e AC power
- eri y measured oltage across battery terminals is 12.5 DC min.

[2] Bell Circuit Bell Bell-... pen Circuit Disconnect Bell- Bell wire leads measure resistance o wire
leads.
- pen circuit indicates break in wiring or de ecti e siren bell
umper Bell Bell- wit 1 resistor Brown Black ed
- eri y trouble clears

[3] General System PC5204 utput 1 pen Circuit I utput 1 is unused: nsure t at terminals 1 AUX are
Trouble umpered wit 1 resistor Brown Black ed
I utput 1 is used: Disconnect wire leads rom 1 AUX
terminals measure t e resistance o t e wire leads
- pen circuit indicates a break in t e wiring

PC5204 AUX eri y oltage measured across AC input terminals is 16-1 AC.
Disconnect all connections to PC5204 AUX terminal.
- eri y AUX oltage is 1 .70 - 1 . 0 DC.

Printer connected to PC5400 o line eri y printer operation out o paper paper am etc.

-Link etwork Fault present e er to t e L GS Installation Manual or details.

-Link ecei er rouble present
-Link Inter ace rouble present

[4] General System amper input on module s open circuit S ort tamper terminal to C M terminal on unused modules connected
Tamper to BUS PC5100 PC510 PC5200 PC5204 PC520 PC5 20
PC5400 PC5700 .

[5] Module Panel does not communicate wit Modules are immediately enrolled and super ised w en detected on
Supervision module s on BUS t e BUS. I a module as been remo ed or i t e slot assignment
o a keypad as been c anged module super ision must be reset.
eypad assigned to incorrect slot. iew t e e ent bu er ia DLS or LCD5500 keypad to identi y t e
speci ic module s in trouble
o reset module super ision:
- nter Program Section 02 .
- Press wait 1 minute or panel to scan BUS .
nter Program Section 0 to identi y modules connected to t e
BUS.

[6] RF Jam Detected Wireless ecei er - excessi e noise C eck or external 4 M signal sources
detected. o disable F am: enable ption 7 in program section 04
subsection 0 .

[7] PC5204 Low PC5204 battery less t an 11.5 DC See 1 Low Battery abo e
Battery
NOTE: This trouble condition will not
clear until the battery voltage is
12.5VDC min., under load.

[8] PC5204 AC Failure o AC at PC5204 AC inputs eri y oltage measured across AC terminals is 16-1 AC.
eplace trans ormer i re uired.

60
 Appendix D: roubles ooting Guide

Trouble Cause Troubleshooting

rouble 2 AC Failure
o AC at panel AC input eri y oltage measured across AC terminals is 16-1 AC. eplace
terminals trans ormer i re uired.

rouble elep one Line rouble

P one Line oltage at IP I G on main Measure t e oltage across IP and I G on t e panel:
panel less t an DC o p one o - ook 50 DC approx
Any p one o - ook 5 DC approx
Wire incoming line directly to IP and I G.
I trouble clears c eck wiring or t e - 1 p one ack.

rouble 4 Failure to Communicate

Panel ails to communicate one or more Connect a andset to IP and I G o t e control panel. Monitor or
e ents to central station t e ollowing conditions:
Continuous dial tone
- e erse IP and I G
ecorded operator message comes on
- eri y correct p one number is programmed
- Dial t e number programmed using a regular telep one to
determine i a must be dialed or i 00 ser ice is blocked.
Panel does not respond to ands akes.
- eri y t e ormat programmed is supported by t e central station.
Panel transmits data multiple times wit out recei ing a ands ake
- eri y t at t e account number and reporting codes are correctly
programmed.
Contact ID and Pulse ormats
Program a X A to transmit a digit 0
SIA ormat
Program a digit 0 to transmit a digit 0

rouble 5 one Fault Press 5 to determine speci ic ones wit a ault trouble
pen circuit is present on one or more nsure ire ones a e a 5.6 resistor Green Blue ed
ire ones on t e main panel or one connected.
expander
emo e t e wire leads rom and C M terminals and measure t e
resistance o t e wire leads.
- An open circuit indicates a break in t e wiring or resistor not
connected.
Connect a 5.6 resistor Green Blue ed across t e and C M
terminals. eri y t e trouble condition clears.
An open circuit is present on PGM2 being nsure t e correct 2.2 end-o -line resistor is connected ed
used as a 2-wire smoke detector input ed ed .
emo e t e wire leads rom PGM2 and AUX terminals and
measure t e resistance o t e wire leads.
- An open circuit indicates a break in t e wiring or no resistor
connected.
Connect a 2.2 resistor ed ed ed across t e PGM2 and
AUX terminals. eri y t e trouble condition clears.
ne or more wireless de ices a e not I t e trouble occurs immediately a con lict wit a ard wired one
c ecked in wit in t e programmed time exists:
- e one being used is already assigned to a PC510 one
expander
- e one being used is assigned as a keypad one
Per orm a Module Placement est Program Section 04 and
eri y t e wireless de ice is in a good location.
- I bad test results occur test t e wireless de ice in anot er location
- I t e wireless de ice now tests good t e original mounting
location is bad
- I t e wireless de ice continues to gi e bad test results replace t e
wireless de ice
A s ort circuit is present on one or more emo e t e wire leads rom and C M terminals and measure t e
ones wit double end-o -line resistors resistance o t e wire leads.
enabled - A s ort circuit indicates a s ort in t e wiring.
Connect a 5.6 resistor Green Blue ed across t e and C M
terminals.
- eri y t e trouble condition clears.

61
PowerSeries - PC1616/PC1832/PC1864

Trouble Cause Troubleshooting

rouble 6 one amper Press 6 to determine speci ic ones wit a tamper trouble
A tamper condition is present on one or Per orm a Module Placement est Section 04
more wireless de ices
iolate t en restore t e tamper:
I no test result t en replace wireless de ice

An open circuit is present on one or more emo e t e wire leads rom and C M terminals.
ones wit double end-o -line resistors
enabled Measure t e resistance o t e wire leads.
pen circuit indicates a break in t e wiring.
Connect a 5.6 resistor Green Blue ed across t e and C M
terminals.
eri y t e trouble condition clears.

rouble 7 Wireless De ice Low Battery Press 7 to toggle t roug speci ic de ices wit low battery trouble
1st press ne or more wireless de ices as a low eplace battery
Wireless ones battery
2nd press NOTE: Replacing batteries will cause a tamper. Replacing cover will
NOTE: The event will not be logged to
and eld eypads restore the tamper causing the associated reporting codes to be sent
the event buffer until the wireless device
rd press low battery delay time expires to the Central Station.
Wireless eys
Program Section 77 pt

rouble Loss o Clock Date

e main panel internal clock is not set o program t e time and date:
nter ✱ 6 Master Code t en Press 1
nter t e time and date in military using t e ollowing ormat:
:MM MM DD
xample. For 6:00 pm une 2 2010
nter: 1 00 06 2 10

IMP A
nsure you a e t e ollowing in ormation a ailable be ore contacting Customer Support

- Control Panel ype and ersion e.g. PC1 64 4.6

NOTE: Version number can be accessed by entering [✱][Installer Code][900] on any LCD keypad.
This information is also located on a sticker on the Printed Circuit Board.
- List o modules connected to Control Panel e.g. PC5100 PC5204 etc.

62
 Appendix E: Template Programming

Appendix E: Template Programming

Template programming allows quick programming of the minimum functions required for basic operation. The below tables are used to determine the desired template to
be used (for information on performing template programming see Section 4 – Programming Descriptions). Each digit represents 1 of the template sections listed below.
The option number selected for each digit will make up the 5 digit template programming code.
• Digit 1 selects Zone 1-8 definition options
Digit 1 selects 1 of the following 6 options for zone definitions for the first 8 zones. A “0” in the digit 1 location indicates that the default settings for the first
8 zones are in place unless overridden. See Sections [001] to [004] on pages 30-31 for defaults.
Option Zn1 Zn2 Zn3 Zn4 Zn5 Zn6 Zn7 Zn8 1 Delay 1
1 1 3 3 3 4 4 4 4 2 Delay 2
2 1 3 3 5 5 5 5 8 3 Instant
3 1 3 3 5 5 5 5 7 4 Interior
4 1 1 3 3 3 3 3 3 5 Interior Stay/Away
5 1 3 3 6 5 5 5 5 6 Delayed Stay/Away
6 1 3 3 6 5 5 5 8 7 Delayed 24-Hour Fire
Refer to Section 4 for Zone definition details 8 Standard 24-Hour Fire
• Digit 2 selects system EOL configuration options
Option [013] Opt 1 [013] Opt 2
1 NC Loops ON OFF
2 SEOL OFF OFF
3 DEOL OFF ON
• Digit 3 selects panel communications options
Option Phone Line 1 Programming Section Phone Line 2 Programming Section
1 Disabled [380] Opt 1 OFF Disabled [380] Opt 1 OFF
SIA automatic Reporting Codes enabled [350] 1st Phone # [04] SIA automatic [350] 2nd Phone # [XX]
2 [380] Opt 1 ON Reporting Codes
enabled
[381] Opt 3 OFF
Contact ID Reporting Codes enabled [350] 1st Phone # [03] SIA automatic [350] 2nd Phone # [XX]
3 [380] Opt 1 ON Reporting Codes
enabled
[381] Opt 7 OFF
SIA automatic Reporting Codes enabled [350] 1st Phone #[04] Residential Dial [350] 2nd Phone # [06]
4 [380] Opt 1 ON Enabled
[381] Opt 3 OFF
Contact ID Reporting Codes enabled [350] 1st Phone # [03] Residential Dial [350] 2nd Phone # [06]
5 [380] Opt 1 ON / Opt 7 Enabled
OFF
Contact ID Reporting Codes enabled [350] 1st Phone # [03] Contact ID Reporting [350] 2nd Phone # [03]
6 [380] Opt 1 ON Codes Enabled
[381] Opt 7 OFF
• Digit 4 selects reporting code configurations
Common Selected Openings/ Zone DLS/Installer
Option
Group Troubles Closings Restorals Lead In/Out
1 ✔ ✖ ✖
2 ✔ ✔ ✖ ✖
3 ✔ ✔ ✖ ✖
4 ✔ ✔ ✔ ✖ ✖
5 ✔ ✔ ✖
6 ✔ ✔ ✖
7 ✔ ✔ ✔ ✖
8 ✔
✔ indicates included, Blank indicates default setting, ✖ indicates disabled

Common Group

Description Phone 1 Phone 2 Sections

Set all Reporting Codes to automatic [320] - [349], [601] - [608] FF
Alarm/Restore call directions enabled ✔ [351][1] ON, [2] OFF
Tamper/Restore Call directions disabled ✔ ✔ [359][1] OFF, [2] OFF
Opening/Closing Call directions disabled ✔ ✔ [367][1] OFF, [2] OFF
Maintenance Call Directions enabled ✔ [375][1] ON, [2] OFF
Test Transmission Call directions disabled ✔ ✔ [376][1] OFF, [2] OFF

63
PowerSeries - PC1616/PC1832/PC1864

Selected Troubles
Trouble [345] Alarms [346] Restoral
Battery FF FF
AC Failure 00 00
Bell Circuit FF FF
Fire, Alarm FF FF
Aux PS FF FF
TLM 00 FF
General System 00 00
General System Supervisory FF FF
FF = Communicate in automatic format , 00 = Disabled

Openings & Closings

Users CLOSINGS, Residential Dial Reporting codes Section
1-8 51 52 53 54 55 56 57 58 [339]
9-16 61 62 63 64 65 66 67 68 [339]
17-24 71 72 73 74 75 76 77 78 [340]
25-32 81 82 83 84 85 86 87 88 [340]
33-40 FF FF FF FF FF FF FF 98 [601]
Users OPENINGS, Residential Dial Reporting codes Section
1-8 11 12 13 14 15 16 17 18 [342]
9-16 21 22 23 24 25 26 27 28 [342]
17-24 31 32 33 34 35 36 37 38 [343]
25-32 41 42 43 44 45 46 47 48 [343]
33-40 FF FF FF FF FF FF FF 98 [605]
Enable Opening/Closings call directions for Phone 2 [367]
Zone Restorals

Zones Alarm Restoral Reporting Codes Section

1-64 00 00 00 00 00 00 00 00 [324]-[327]

00 = Disabled

DLS/Installer Lead IN/OUT

Miscellaneous Maintenance Reporting Codes Section

DEF DEF DEF 00 00 DEF DEF DEF DEF DEF 00 00 [347]

DEF = No change to default values, 00 = Disabled

• Digit 5 selects DLS connection options.

Option Programming Section DLS Connection/Call back setting

1 [401] Option 1 OFF Double Call Disabled, Call Back Disabled

Option 3 OFF
[406] 0 Number of rings to answer on set to 0

2 [401] Option 1 ON Double Call Enabled, Call Back Disabled

Option 3 OFF
[406] 9 Number of rings to answer on set to 9

3 [401] Option 1 ON Double Call Enabled, Call Back Enabled

Option 3 ON
[406] 9 Number of rings to answer on set to 9

64
 Appendix F: Communicator Format Options

Appendix F: Communicator Format Options

This section requires two 2-digit entries to set the communi- • If an event’s reporting code is programmed as [00] or [FF],
cations format that is to be used for each phone number (1 the panel will not attempt to call central station.
per phone number). The 3rd telephone number uses the for- • If the reporting code for an event is programmed as any-
mat programmed for the 1st telephone number. thing from [01] to [FE], the panel will send the programmed
reporting code.
Entry Communication Format
• Account numbers must be four digits.
01 20 BPS, 1400 HZ handshake • If the digit ‘0’ is in the account number substitute the HEX
02 20 BPS, 2300 HZ handshake digit ‘A’ for the ‘0’.
03 DTMF CONTACT I.D. • All reporting codes must be two digits.
04 SIA FSK • If the digit ‘0’ is in the reporting code substitute the HEX
05 Pager digit ‘A’ for the ‘0’.
• To prevent the panel from reporting an event program the
06 Residential Dial
reporting code for the event as [00] or [FF].
07 10 BPS, 1400 Hz handshake
08 10 BPS, 2300 Hz handshake Contact ID Sends Automatic
09 For Future Use Reporting Codes . . . . . . . . . . . . . . . . . Section [381], Option [7]
10 For Future Use
SIA (Level 2)
11 For Future Use
SIA is a specialized format that will communicate information
12 For Future Use quickly using frequency shift keying (FSK) rather than pulses.
13 For Future Use The SIA format will automatically generate the type of signal
Reporting Codes being transmitted, such as Burglary, Fire, Panic etc. The two
digit reporting code is used to identify the zone or access
• SIA -0 is valid in Account or Rep Code (not 00 in a Report-
code number.
ing code though)
• ADEMCO Contact ID - 0 is not valid in Account or Rep If the SIA format is selected the panel can be programmed
Code (A must be used, 10 in checksum) to automatically generate all zone and access code num-
• BPS Formats - 0 is not valid in Account or Rep Code (A bers eliminating the need to program these items.
must be used) If the SIA Sends Automatic Reporting Codes option is
• SIA - This format uses 300 Baud FSK as the communica- enabled the panel will operate as follows:
tion media. The Account Code can be 4 or 6 hexadecimal 1. If the reporting code for an event is programmed as [00] the
digits in length, All reporting codes must be 2 digits in panel will not attempt to call the central station.
length. The SIA format will transmit a 4 (or 6) digit account 2. If the reporting code for an event is programmed as anything
code, a 2-digit identifier code and a 2-digit reporting code.
from [01] to [FF] the panel will AUTOMATICALLY generate
The 2-digit identifier is pre programmed by the panel.
the zone or access code number.
Contact ID 3. Bypassed zones will always be identified when partial clos-
Contact ID is a specialized format that will communicate ing the system.
information quickly using tones rather than pulses. In addi- The Communicator Call Direction Options can be used to
tion to sending information more quickly the format also disable reporting of events such as Openings/Closings.
allows more information to be sent. For example, rather than Also, if all the Opening/Closing reporting codes were pro-
reporting an alarm zone 1 the Contact ID format can also grammed as [00] the panel would not report.
report the type of alarm, such as Entry/Exit alarm zone 1. If the SIA Sends Automatic Reporting Codes option is
If Contact ID Sends Automatic Reporting Codes is disabled the panel will operate as follows:
selected, the panel will automatically generate a reporting 1. If the reporting code for an event is programmed as [00] or
code for each event. These identifiers are listed in Appendix [FF] the panel will not attempt to call the central station.
A. If the Automatic Contact ID option is not selected, report-
ing codes must be programmed. The 2-digit entry deter- 2. If the reporting code for an event is programmed as anything
mines the type of alarm. The panel will automatically from [01] to [FE] the panel will send the programmed report-
generate all other information, including the zone number. ing code.
NOTE: If the Automatic Contact ID option is selected, the panel 3. Bypassed zones will not be identified when partial closing
will automatically generate all zone and access code numbers, the system.
eliminating the need to program these items. NOTE: The zone number for Zone Low Battery and Zone Fault
NOTE: The zone number for Zone Low Battery and Zone Fault events will not be identified when Programmed SIA is used.
events will not be identified when Programmed Contact ID is
used. SIA Sends Automatic Reporting CodesSection [381], Option [3]
If the Contact ID uses Automatic Reporting Codes Communicator Call Direction Options . . . Section [351] to [376]
option is enabled, the panel will operate as follows: SIA Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix A
• If an event’s reporting code is programmed as [00], the
panel will not attempt to call the central station. Residential Dial
• If the reporting code for an event is programmed as any- If Residential Dial is programmed and an event that is pro-
thing from [01] to [FF], the panel will automatically gener- grammed to communicate occurs, the panel will seize the
ate the zone or access code number. See Appendix A for line and dial the appropriate telephone number(s). Once the
a list of the codes which will be transmitted. dialing is complete, the panel will emit an ID tone and wait
If the Contact ID uses Programmed Reporting Codes for a handshake (press a 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, ✱ or #
option is enabled, the panel will operate as follows: key from any telephone). It will wait for this handshake for

65
PowerSeries - PC1616/PC1832/PC1864

the duration of Post Dial Wait for Handshake timer. Once Telephone Line Monitoring (TLM)
the panel receives the handshake, it will emit an alarm tone When the TLM Enable option is selected, the panel will
over the telephone line for 20 seconds. If several alarms supervise the telephone line and will indicate a trouble con-
occur at the same time, only one call will be made to each dition if the telephone line is disconnected.
telephone number the panel is programmed to call. If the TLM Enable option is ON, the panel will check the tele-
phone line every 10 seconds. If the telephone line voltage is
Communicator Call Direction Options . . . .Section [361] to [368]
below 3V for the number of checks programmed in the TLM
Trouble Delay section, the panel will report a TLM trouble.
Pager Format The default number of checks is 10. Enter a number from
The Communicator Format option for either telephone (000) to (255) in the TLM Trouble Delay section to change
number can be programmed for Pager Format. If an event the number of checks before the TLM trouble is reported.
occurs and the Communicator Call Direction options Programming a delay means that a momentary interruption
direct the call to a telephone number with the Pager Format of the telephone line will not cause a trouble condition.
selected the panel will attempt to page. If the TLM Trouble Beeps When Armed option is enabled,
When calling a pager extra digits will be required to make it the panel will indicate a TLM trouble at the keypad while the
work properly.The following is a list of Hex digits and what system is armed. To activate the bell output in the case of a
function they perform: TLM trouble while the system is armed, the TLM Audible
Hex [A] - not used (Bell) When Armed option must be selected.
Hex [B] - simulates the * key on a touch tone telephone When the trouble condition is restored, the panel can send a
Hex [E] - two second pause TLM Restoral reporting code. Any events which occur while
Hex [C] - simulates the [#] key on a touch tone telephone the telephone line is down will also be communicated. If an
Hex [F] - end of telephone number marker alternate communicator is being used, the panel can be pro-
Hex [D] - forces the panel to search for dial tone grammed to report a TLM Trouble Reporting Code.
The panel will attempt to call the pager one time. After dial-
ing the digits in the telephone number the panel will send
the account number and reporting code followed by the [#]
key (Hex [C]).
There is no ringback when using Pager Format. The panel
has no way of confirming if the pager was called success-
fully; a failure to communicate trouble will only be generated
once the maximum number of attempts has been reached.
NOTE: Do not use the digit C in a reporting code when using
Pager Format. In most cases, the digit C will be interpreted as a
[#], which will terminate the page before it has finished.
NOTE: If the panel detects a busy signal, it will attempt to page
again. It will make the maximum number of attempts pro-
grammed in section [165].
Force dialing should be disabled when using Pager format.
When using Pager format, you must program two hex digit E’s at
the end of the telephone number.
Pulse Formats
Depending on the pulse format selected the panel will com-
municate using the following:
• 3/1, 3/2, 4/1 or 4/2
• 1400 or 2300 Hz handshake
• 10 or 20 bits per second
• non-extended
The digit ‘0’ will send no pulses and is used as a filler. When
programming account numbers enter four digits. When pro-
gramming a three digit account number the fourth digit must
be programmed as a plain ‘0’ which will act as a filler digit.
If an account number has a ‘0’ in it, substitute a HEX digit ‘A’
for the ‘0’. Examples:
• 3 digit account number [123]- program [1230]
• 3 digit account number [502] - program [5A20]
• 4 digit account number [4079] - program [4A79]
When programming reporting codes two digits must be
entered. If one digit reporting codes are to be used the sec-
ond digit must be programmed as a ‘0’. If a ‘0’ is to be trans-
mitted substitute a HEX digit ‘A’ for the ‘0’.
Examples:
• 1 digit reporting code [3] - program [30]
• 2 digit reporting code [30] - program [3A]
To prevent the panel from reporting an event program the
reporting code for the event as [00] or [FF].

66
 Appendix F: Communicator Format Options

SAFETY INSTRUCTIONS FOR SERVICE PERSONNEL

WARNING: When using equipment connected to the telephone network, there are basic safety instructions that should
always be followed. Refer to the Safety Instructions provided with this product; save them for future reference. Instruct the
end-user regarding the safety precautions that shall be observed when operating this equipment.

Selecting a Suitable Location for the Alarm Controller

Use the following list as a guide to find a suitable place for this equipment:
• Locate the control panel near a telephone socket and a power outlet.
• Select a place that is free from vibration and shock.
• Place the alarm controller on a flat, stable surface and follow the installation instructions:
Do NOT locate this product where persons can walk on the secondary circuit cable(s).
Do NOT connect the alarm controller to electrical outlets on the same circuit as large appliances.
Do NOT select a place that exposes the alarm controller to direct sunlight, excessive heat, moisture, vapors, chemicals
or dust.
Do NOT install this equipment near water (e.g., bathtub, wash bowl, kitchen/laundry sink, wet basement, or near a
swimming pool).
Do NOT install this equipment and its accessories in areas where there is a risk of explosion.
Do NOT connect this alarm controller to electrical outlets controlled by wall switches or automatic timers.
AVOID sources of radio interference.
AVOID setting up the equipment near heaters, air conditioners, ventilators, and/or refrigerators.
AVOID locating this equipment close to or on top of large metal objects (e.g., metal wall studs).

Safety Precautions Required During Installation

• NEVER install this equipment and/or telephone wiring during a lightning storm.
• NEVER touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network
interface.
• Ensure that cables are positioned so that accidents can not occur. Connected cables must not be subject to excessive
mechanical strain.
• For Direct Plug-in versions, use the transformer supplied with the device.

The power supply must be Class II, FAIL SAFE with double or reinforced insulation between the PRIMARY and
SECONDARY circuit/ENCLOSURE and be an approved type acceptable to the local authorities. All national wiring rules
shall be observed.

67
 Limited Warranty
Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of
defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls shall, at its option, repair or Items Not Covered by Warranty
replace any defective product upon return of the product to its factory, at no charge for labour and materials. Any replacement and/or repaired In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i) freight cost to the repair centre; (ii)
parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is longer. The original purchaser must promptly products which are not identified with DSC's product label and lot number or serial number; (iii) products disassembled or repaired in such a
notify Digital Security Controls in writing that there is defect in material or workmanship, such written notice to be received in all events prior to manner as to adversely affect performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned
expiration of the warranty period. There is absolutely no warranty on software and all software products are sold as a user license under the terms for replacement under warranty will be credited or replaced at DSC's option. Products not covered by this warranty, or otherwise out of warranty
of the software license agreement included with the product. The Customer assumes all responsibility for the proper selection, installation, due to age, misuse, or damage shall be evaluated, and a repair estimate shall be provided. No repair work will be performed until a valid
operation and maintenance of any products purchased from DSC. Custom products are only warranted to the extent that they do not function purchase order is received from the Customer and a Return Merchandise Authorization number (RMA) is issued by DSC's Customer Service.
upon delivery. In such cases, DSC can replace or credit at its option.
International Warranty Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reasonable number of attempts will be limited
The warranty for international customers is the same as for any customer within Canada and the United States, with the exception that Digital to a replacement of the product, as the exclusive remedy for breach of warranty. Under no circumstances shall Digital Security Controls be liable
Security Controls shall not be responsible for any customs fees, taxes, or VAT that may be due. for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other
Warranty Procedure legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost
of substitute or replacement equipment, facilities or services, down time, purchaser’s time, the claims of third parties, including customers, and
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized distributors and dealers have injury to property. The laws of some jurisdictions limit or do not allow the disclaimer of consequential damages. If the laws of such a jurisdiction
a warranty program. Anyone returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will apply to any claim by or against DSC, the limitations and disclaimers contained here shall be to the greatest extent permitted by law. Some
not accept any shipment whatsoever for which prior authorization has not been obtained. states do not allow the exclusion or limitation of incidental or consequential damages, so that the above may not apply to you.
Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover: Disclaimer of Warranties
• damage incurred in shipping or handling; This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied
• damage caused by disaster such as fire, flood, wind, earthquake or lightning; warranties of merchantability or fitness for a particular purpose) and of all other obligations or liabilities on the part of Digital Security Controls.
• damage due to causes beyond the control of Digital Security Controls such as excessive voltage, mechanical shock or water damage; Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to
• damage caused by unauthorized attachment, alterations, modifications or foreign objects; change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and limited
• damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.); warranty are governed by the laws of the province of Ontario, Canada.
• defects caused by failure to provide a suitable installation environment for the products;
• damage caused by use of the products for purposes other than those for which it was designed; WARNING: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite
• damage from improper maintenance;
• damage arising out of any other abuse, mishandling or improper application of the products. frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform
as expected.
Out of Warranty Repairs
Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory according to the following
conditions. Anyone returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not
accept any shipment whatsoever for which prior authorization has not been obtained.

Products which Digital Security Controls determines to be repairable will be repaired and returned. A set fee which Digital Security Controls has
predetermined and which may be revised from time to time, will be charged for each unit repaired.

WARNING - READ CAREFULLY

Note to Installers • Smoke Detectors
This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may
of the users of this system. have been improperly installed or positioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the
other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence or building.
System Failures Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well. Smoke detectors may
This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of
where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. flammable materials, overloaded electrical circuits, children playing with matches or arson.
Some but not all of these reasons may be:
Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid
• Inadequate Installation injury or death.
A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated by a security professional to ensure that • Motion Detectors
all access points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between
other building materials must be of sufficient strength and construction to provide the level of protection expected. A reevaluation must be done during and after any intruders and intended occupants. Motion detectors do not provide volumetric area protection. They have multiple beams of detection and motion can only be
construction activity. An evaluation by the fire and/or police department is highly recommended if this service is available. detected in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass
• Criminal Knowledge doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows
This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop or any other part of the detection system will impair its proper operation.
techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient temperature rises near
and that it be updated or replaced if it is found that it does not provide the protection expected. or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters,
• Access by Intruders radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so on.
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, • Warning Devices
disconnect a warning device, or interfere with or prevent the proper operation of the system. Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an intervening wall or door. If warning devices
• Power Failure are located on a different level of the residence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however
from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device loud, may not be heard by a hearing-impaired person.
operates only by AC power, any interruption, however brief, will render that device inoperative while it does not have power. Power interruptions of any length are • Telephone Lines
often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its
immediately conduct a complete system test to ensure that the system operates as intended. operation by more sophisticated means which may be difficult to detect.
• Failure of Replaceable Batteries • Insufficient Time
This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The expected battery life is a function of the There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the emergency due to their inability to respond
device environment, usage and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the to the warnings in a timely manner. If the system is monitored, the response may not occur in time to protect the occupants or their belongings.
expected battery life. While each transmitting device has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to oper- • Component Failure
ate as expected. Regular testing and maintenance will keep the system in good operating condition. Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended due to the failure of a component.
• Compromise of Radio Frequency (Wireless) Devices • Inadequate Testing
Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jamming or other Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be
inadvertent radio signal interference. tested weekly and immediately after a break-in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or
• System Users outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices and any other operational devices that are part of
A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physical disability, inability to reach the device in time, or the system.
unfamiliarity with the correct operation. It is important that all system users be trained in the correct operation of the alarm system and that they know how to respond •Security and Insurance
when the system indicates an alarm. Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a substitute for property owners, renters,
or other occupants to act prudently to prevent or minimize the harmful effects of an emergency situation.

IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components
is copyrighted and is purchased under the following license terms:
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of this
• This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired the Software EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC”), the manufacturer of the (g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.
integrated security systems and the developer of the software and any related products or components (“HARDWARE”) which You acquired. 3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images,
• If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT accom- photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE
panied by new HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer soft- PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and
ware, and may include associated media, printed materials, and “online” or electronic documentation. intellectual property rights in and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the
• Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no
under the terms of that license agreement. rights to use such content. All rights not expressly granted under this EULA are reserved by DSC and its suppliers.
• By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound 4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity
by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to subject to Canadian export restrictions.
the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it. 5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
SOFTWARE PRODUCT LICENSE 6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall be Toronto, Canada, and the
treaties. The SOFTWARE PRODUCT is licensed, not sold. language of the arbitration shall be English.
1.GRANT OF LICENSE This EULA grants You the following rights: 7. LIMITED WARRANTY
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed. (a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL MEET
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
different computers, including a workstation, terminal or other digital electronic device (“Device”). In other words, if You have several (b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics
workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used. of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any (c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR
given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE
make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE. AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
SOFTWARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this (d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER
limitation. You may not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER
compliance with the terms and conditions of this EULA. WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE
on more than one HARDWARE unit. PRODUCT.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the (e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL,
HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT,
this EULA. NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO,
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF
site. SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF
(e)Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE, THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.
provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, the media and printed materials, WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent
any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE
transfer must also include all prior versions of the SOFTWARE PRODUCT. PRODUCT to fail to perform as expected.
FCC COMPLIANCE STATEMENT
NOTE: CAUTION: Changes or modifications not expressly Equipment Maintenance Facility
approved by Digital Security Controls could void your authority to If trouble is experienced with this equipment PC1616, PC1832, PC1864 for repair or war-
use this equipment. ranty information, please contact the facility indicated below. If the equipment is causing
This equipment has been tested and found to comply with the limits for a Class B digital de- harm to the telephone network, the Telephone Company may request that you disconnect
vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable the equipment until the problem is solved. This equipment is of a type that is not intended
protection against harmful interference in a residential installation. This equipment generates, to be repaired by the end user.
uses and can radiate radio frequency energy and, if not installed and used in accordance with DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
the instructions, may cause harmful interference to radio communications. However, there is
Additional Information
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be deter-mined by turn- Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
ing the equipment off and on, the user is encouraged to try to correct the interference by one
Alarm dialling equipment must be able to seize the telephone line and place a call in an
or more of the following measures:
emergency situation. It must be able to do this even if other equipment (telephone, answer-
• Re-orient the receiving antenna. ing system, computer modem, etc.) already has the telephone line in use. To do so, alarm
• Increase the separation between the equipment and receiver. dialling equipment must be connected to a properly installed RJ-31X jack that is electrical-
• Connect the equipment into an outlet on a circuit different from that to which the ly in series with and ahead of all other equipment attached to the same telephone line. Prop-
receiver is connected. er installation is depicted in the figure below. If you have any questions concerning these
• Consult the dealer or an experienced radio/television technician for help. instructions, you should consult your telephone company or a qualified installer about in-
The user may find the following booklet prepared by the FCC useful: "How to Identify and stalling the RJ-31X jack and alarm dialling equipment for you.
Resolve Radio/Television Interference Problems". This booklet is available from the U.S.
Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is
a label that contains, among other information, the FCC registration number and ringer
equivalence number (REN) for this equipment. If requested, this number must be provided
to the Telephone Company.
PC1864 Product Identifier US: F53AL01BPC1864
PC1832 Product Identifier US: F53AL01BPC1832
PC1616 Product Identifier US: F53AL01BPC1614
REN: 0.1B
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone net-
work must comply with the applicable FCC Part 68 rules and requirements adopted by the
ACTA. A compliant telephone cord and modular plug is provided with this product. It is INDUSTRY CANADA STATEMENT
designed to be connected to a compatible modular jack that is also compliant. See installa- NOTICE: This Equipment meets the applicable Industry Canada Terminal Equipment Tech-
tion instructions for details. nical Specifications. This is confirmed by the registration number. The abbreviation, IC, be-
Ringer Equivalence Number (REN) fore the registration number signifies that registration was performed based on a Declaration
of Conformity indicating that Industry Canada technical specifications were met. It does not
The REN is used to determine the number of devices that may be connected to a telephone
imply that Industry Canada approved the equipment.
line. Excessive RENs on a telephone line may result in the devices not ringing in response to
an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The
number of devices that may be connected to a line, as determined by the total RENs, contact REN assigned to each terminal equipment provides an indication of the maximum number of
the local Telephone Company. For products approved after July 23, 2001, the REN for this terminals allowed to be connected to a telephone interface. The termination on an interface
product is part of the product identifier that has the format. may consist of any combination of devices subject only to the requirement that the sum of the
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point Ringer Equivalence Numbers of all devices does not exceed five.
(e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
PC1616 Registration numberIC: 160A-PC1614
Incidence of Harm
PC1832 Registration numberIC: 160A-PC1832
If this equipment PC1864/PC1832/PC1616 causes harm to the telephone network, the tel-
ephone company will notify you in advance that temporary discontinuance of service may PC1864 Registration numberIC: 160A-PC1864
be required. But if advance notice is not practical, the Telephone Company will notify the This Class B digital apparatus meets all requirements of the Canadian interference-caus-
customer as soon as possible. Also, you will be advised of your right to file a complaint ing equipment regulations.
with the FCC if you believe it is necessary. Cet appareil numérique de la Classe B respecte toutes les exigences de règlement sur le
materiel brouilleur du Canada.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or pro-
cedures that could affect the operation of the equipment. If this happens the Telephone
Company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.

The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of the
trademarks is strictly prohibited and Tyco International Ltd. will aggressively enforce its intellectual property rights to the fullest extent of the law,
including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco International Ltd. are the property of their respective
owners, and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all
features. Availability varies by region; contact your sales representative.

© 2012 Tyco International Ltd. and its Respective Companies.

All Rights Reserved.
Tech Support: 1-800-387-3630 (Canada & U.S.) or 905-760-3000
Printed in Canada • www.dsc.com 29008247R002