TEVERUN FIGHTER

MANUAL

NINGBO TEVERUN TECHNOLOGY CO.,LTD.

Add:Xiwang Industry Zone,Hengjie Town, 315181,Ningbo,China

Email:[email protected]
Web:www.teverun.com
 W AR N IN G

Before Reading Manual

Please read this manual carefully
N O T ICE before using this product
CONTENTS 1) General safety guidelines and restrictions
* Even if the it is within the warranty period, you may be liable for any accident caused by any of the following causes.
L

1. Be careful of water!
Safety guidelines and restrictions P2 This product and componentsare not waterproof. Don’t let the water get into
Product structure P4 the product and components.
*Never use it, if the road is wet due to the rain, snow, hailstone.
Name of parts P5 *If you wash or spread water to electric devices, it can result in malfunction or fire.
Product unfolding P6
2. Beware of folding and spinning parts!
Product folding P6 If parts of the body, as a finger or hair, get caught in the spinning or folding
parts of the product, this may lead to severe injuries. Please be careful.
Lock handle bar P6
TFT display instruction P7
3. No acrobatics
How to use the charger correctly P15 Stunts and jumps such as jumping and dropping are prohibited as they can
cause a great impact on the product and can cause of malfunction and
Safety precautions for Lithium battery P16 L
accidents.
Safety guidelines before driving P17 4. No companion boarding
Check and maintenance P18 This product is intended for one adult only, so children,infants, or two people

Important check list P20 are prohibited from boarding.

Before Reading the Manual 5. Don’t tune by yourself

Do not open or tune the electric parts (battery, controller or motor
This manual contains important information to help you to use your product more safely. system.
L
For your safety, there are warnings of 'Danger', 'Warning', and ‘Caution’
depending on the degree of danger and the meanings are below. 6. No companion boarding
Unlicensed, driving after drinking, loading cargo on the scooter is prohibited.
(More than bike or bicycle license is required) Please comply with the Road
Traffic.Act and related laws and regulations according to the place of use.
DANGER Indicates a hazardous situation that will result in serious injury.

7. Beginners and seniors are encouraged to use at low speed

Beginners who are not accustomed to use the product, seniors and others
WARNING Indicates a hazardous situation that could result in serious injury.
Beginners sick and disabled
should avoid high speed mode driving and recommend low speed driving.
L
Low speed/mode/use/proposal
L In addition, please use after practice how to ride safely in a wide place.
Indicates a hazardous situation that couldresultin minor or
CAUTION moderate injury. 8. Do not sudden brake with front brake
If there is a risk of overturning, sudden deceleration should be done safely.
Do not apply any unusual behaviors or artificial forces, such as stopping with
NO emergency braking
Emergency brake your feet.

04 Dualtron XII User Manual

01 02
 /
Slow mode is recommended

( L3)

Product structure
10. Do not drive on steep slopes
Acceptable gradeability is different for each product. Excessive hill roads
exceeding the specification may cause damage to the product (parts) due
to temperature cut, overcurrent, or low voltage cut, which may cause the Scooter size
product to malfunction.
Comply with
the related laws
11. Safety warning when lifting the product
Please always lift the product with at least one other person.
When lifting the product, please be careful not to damage your back or
knees.

1275mm
12. Be sure to wear safety equipment
For the safety of passengers, be sure to wear a full face helmet and the
other protective gear (for knees, elbows, hands, upper body) and do not wear
shoes such as slippers or high heels that can interfere with driving.

2) Precaution before driving

Do not sudden brake
1. Night driving should be avoided at all times. Always wear helmets and other body guards and
Novice Elderly

Slowdrive
1300mm
safely.
mode is recommended

2. Select the mode that suits you and drive. In order to cope with sudden situations, be prepared
to slow down by holding the brake at all times.
3. When turning left / right, slow down to avoid the danger of overturning or slipping, then slowly
turn safely.
4. To go backwards safely, get off the product only after coming to a complete stop. Handle bar
5. It is prohibited to use in any places that are slippery, crowded, have a steep slope, or are
uneven. TFT display TFT control button
6. When crossing a pedestrian crossing, get off from the product for pedestrian safety.
7. Do not drive in a way that threatens any other means of transport, such as animals,
NFC
pedestrians, bicycles, motorcycles, cars, etc.
8. When passing speed bumps and road obstacles,
be sure to slow down.
9. When decelerating or braking, do not stop with
your foot, but by using the brake appropriately.
10. Be careful as there is a risk of burns due to heat
from the motor and brake (especially disk rotor)
after driving. accelerator Muti button
11. It is prohibited to drive by holding the handle with
one hand; please use both hands at all times.
12. Do not ride or drive when the kick stand is down.

Do not sudden brake Dualtron XII User Manual 05

03 04
Name of Parts Product unfolding

LOCK

TFT display
Handle grip

Brake level

Product folding
Hook
Steering tube
OPEN
SLIDE UP
PRESS

Rubber mat

Folding level
Lock handle bar
fender
Turning
damper
brake Screw in X 4

Fender
Arm
kickstand
tire
Deck

Motor

05 06
TFT display instruction 5.4 Adjusting 5 levels backlight brightness：1st level is the darkest, 5th is the
lightest.
5.5 ECO and 1-5 levels: Can be set according to customers’ habits.
5.6 Mileage indicator: Odometer/Trip distance/ Riding time.
5.7 Clock display: inner small battery, keep time when the display is closed
5.8 Power indicator：Real time power indicator, digital or analog.
5.9 Error code indicator.
5.10 Speed limit adjustment function: total speed limit and gear speed limit can
be set.
5.11 Current limit adjustment function
5.12 USB charging port: provide rated charging for mobile devices. Current:
500mA/5V.
5.13 Software upgrade: Software can be upgraded through UART.
5.14 Speed measurement magnets (number of pole pairs) adjustment function:
the number of speed measurement magnets (magnetic poles) can be set.
5.15 Level parameter setting: you can set the parameters of the levels.

TFT screen instructions

Information:

Brake F & R motor work simultaneously

Battery
电量显示
Headlight

Clock
时钟显示 Power
功率显示

Introduction Speed
速度信息

5.1 Screen size: 3.5inch color TFT screen.

5.2 Kilometer / Mile: Can be set according to customers’ habits. Fixed
定速巡航Speed Assist
档位显示 level
5.3 Intelligent power indicator contains below: It can provide a stable power Cruise Control
indication through the optimization algorithm. The power is not affected by the Mileage and speed
start-stop fluctuation of the motor. If the system supports battery communication,
the accurate percentage of power will be displayed.

07 08
Status:
6.11 Real-time temperature can be indicated.

Functional Description

Up Power

Down M
Error code
Rear motor
7.1 Power On/Off
Temperature
Press and hold Power button for 1 second, it can turn on/off the display. The display
Current will automatically shut down when there is no operation & ride for 10 minutes（time
interval can be set）.

Front motor *If the display has been set power-on password, you need to input the right
password when starting.
6.1 Display interface: The default value is information mode, click M key to switch
to the status interface
7.2 Assist Level Operating
6.2 Speed model：AVG SPEED/MAX SPEED/RT SPEED
Short press UP/DOWN button can change the assist levels. Available assist levels
6.3 Headlight indication：When the headlight is working, showing
include ECO, 1,2,3,4 and 5.
6.4 Brake indication：When the brake is working, showing !
6.5 Assist level: showing current assist levels
7.3 Headlight/Display Model Change
6.6 Speed indication：Km/h or MPH
Press and hold UP button for 1 second, the backlight brightness will be lowered and
6.7 Clock information can be displayed.
headlight will be on (controller support is needed). At the same time, switching
6.8 Real-time current information can be indicated.
daytime/night mode. Press and hold UP button for 1 second again, headlight will be
6.9 Motor status can be indicated: ON and OFF.
off and change the display mode.
6.10 Error code can be displayed. Please refer to the common error code.

*The backlight brightness has 5 levels and users can adjust it according to
Error code Error descriptions
their demands.
“1” is shown at the bottom of the screen Motor is out of phase
“2” is shown at the bottom of the screen Hall fault 7.4 Data Cleanup
“4” is shown at the bottom of the screen Handlebar fault Pressing and holding UP & DOWN buttons concurrently for 1 second can reset
temporary data, including AVG Speed / MAX Speed / Trip / Time.
“5” is shown at the bottom of the screen Under voltage protection

“6” is shown at the bottom of the screen Controller fault

*These temporary data will not be erased when power is off.
“7” is shown at the bottom of the screen Communication error
“8” is shown at the bottom of the screen Over-temperature protection

09 10
MENU Parameter Setting 8.6 Information：Press M button and choose
Information to enter information menu. It will shows
In the state of power on, press the M button twice speed mode and mileage mode information. After
(time interval must be within 0.3S), the system will finish setting, press M button or POWER to choose
enter the parameter setting menu. Press M button return to main menu.
twice again to exist setting state (time interval must
be within 0.3S). Information display
In the MENU setting interface, press M button to
8.7 Advance setting: Press M to enter into
confirm and press POWER to cancel. Press UP or
Advance Setting interface and press UP/DOWN to
DOWN to select the adjusting items. Press M button,
adjust the password and enter the advance setting.
the parameter to be set will be blinking. If you want
Input right password to enter the submenu. The
to adjust related parameters, please press UP or
password is 4 digits and the default value is “2112”.
DOWN. Then press M to save and press POWER or
If the power-on password is turned on, the
select EXIT to back to the main menu. In the function
advanced setting password is the power-on
selection interface, press M button twice consecutive-
Function select menu password. The options and functions are as follows.
ly or select EXIT to exit menu.

8.1 Brightness：Press M button to enter the setting menu. Adjusting the brightness
Speed limit→**%
1-5 by pressing UP/DOWN button.1 is the darkest, 5 is the brightest. Press M to
Cruise→OFF/AUTO/MANUAL
confirm and return to the main menu.
ABS ON/OFF
8.2 Unit system: Metric/Imperial
Speed magnets number:1~88
8.3 Auto off: Press UP/DOWN button to change the auto power off time. The
Assist level parameter:
number from 1 to 10 represents time (minutes) to shut down and the default value is
Assist1/ Assist2/ Assist3/ Assist4/ Assist5 parameters can be set.
10 minutes. Please press M to confirm or press POWER to cancel the settings.
8.4 Clock: Press M button to enter the clock setting menu. Press UP/DOWN button
to set Hour/Min. Please press M to confirm or press POWER to cancel the settings.
After setting the parameters, please press M to confirm and return to the main Speed limit: 1-100%
menu. EABS level: 1-5
8.5 Start password open and set: Press M button to enter password setting F start level: 1-5
interface. Select ON/OFF to turn on or off the start password. Select Reset the R start level: 1-5
Password to enter the new password setting interface. Select Back or press the F current is limited
POWER button to return to the main menu. the default password is "0000". R current is limited

Export→NO/YES.
When the switch is on, the speed is limited to 25% and non-zero start.
Temp protection: 80-155℃
Zero start→N/Y
Select Exit or POWER button to return to the main menu.
enter the password selections enter the new password

11 12
8.8 Factory Setting：Enter Factory settings menu. Select YES will restore all parameter Assembly instructions
to factory settings.

9.1 Please pay attention to the screw’s torque value. Damages caused by excessive
torque are not covered by the warranty.

M4*12mm

Factory setting M3*8mm

8.9 Wheel size setting: Press UP/DOWN button to switch wheel size: 8-14 inches.
Wrong wheel size selection will lead to abnormal speed. Press M button to confirm
current setting or press POWER button to cancel current setting. M4*8mm
8.10 Voltage
Power system: 48V/60V/72V
8.11 Exit

9.2 Clamps are suitable for 3 sizes of handlebar, 31.8mm, 25.4mm, and 22.2mm.
Customers can choose according to their own demands. Handlebar of 25.4mm and
22.2mm must be assembled with the corresponding adapter rings.

Gasket installation diagram

13 14
How to use the charger correctly Safetyprecautions
Safety precautionsfor
forLithium
Lithium battery
battery

3P charger connector 3P fast charger connector

1) Care Lithium batteries should be protected from direct exposure to children and pets.
(Handle part 1ea) (Main frame 3ea)
1) Basic charging method 2) Performance 1. Lithium battery is affected by external temperature. In the winter,

Lithium
when the temperatures are low, the performance of the battery may be temporarily
1. Open the charger port cap and connect deteriorated and the mileage and power output is reduced.
3 2 1
it to the connector of the charger and 3 2 1 2. Lithium battery has a characteristic that discharge performance is reduced by more
connect it to the household outlet. than 15% when charging / discharging 300 times or more. If usage time is shortened due
to long usage, it should be replaced with a genuine one through the nearest point.
2. Charging status indicator (Red) Charging
3) Charging 1. Lithium battery should be used only with genuine battery and charger
(Green) Charging complete supplied from the manufacturer. Any problems caused by use of battery made by the manufacturer,
3. Be sure to close the charger port cap when driving or storing except when charging. mixed use, or using the charger are not covered by the manufacturer.
4. When connecting the connector to the charger port, there may be metallic sparks due to 2. Charging the lithium battery with a non-genuine charger may cause malfunction or fire.
voltage difference, but this is normal. 3. The lithium battery should be charged in a well-ventilated, dry place and around the charger in a
place where there is no flammable material.
2) Basic charging method * Failure of the charger and abnormal conditions can cause 4. Lithium battery should be charged at 0 ~ 45°C and discharged within -10 ~ 60°C .
electric shock and fire. Learn the correct usage and prevent safety accidents in advance. The sub-battery must be charged at 0 to 50°C and discharged within -20 to 75°C.
Charging or discharging at a temperature outside this range may cause malfunction, fire or explosion.
1. Manufacturers and sellers are not 2. The charger is forbidden to be used 5. In case of moving from cold outside to warm indoor, please charge it after 1 ~ 2 hours.
responsible for any problems in places subject to high humidity, This is to prevent condensation from occurring inside the product due to the temperature difference.
arising from any disassembly, heat, flammable materials, 4) Storage 1. Lithium batteries should be kept away from snow, rain and direct sunlight.
modification, or mixing with other confined spaces, or where there
chargers. is no ventilation such as in a car. Do not store or charge them in a trunk or hot room.
Select a dry place and store at room temperature (10 ~ 20 ć).
3. The charger is not waterproof. It is 4. Children and pets should not be 2. When storing for more than 3 months, charge the remaining battery level to 70 ~ 80% (do not store full charge).
thoroughly controlled to prevent allowed to approach the charger
moisture from entering the when they come into contact 5) Trouble symptom, safety 1. Lithium battery should be discontinued immediately if it is damaged
with them, as they may cause an or there is leakage of battery, sour odor, appearance deformation, etc. Please contact the place of
charger. electric
DANGERshock.
purchase to get technical support and service.
5. If the charger lamp does not light, 6. Unplug the charger when you are away from 2. If overheat, smoke, or ignition is detected in a product with lithium battery, immediately stop charging
charger fall down, strong external the home for long periods. and use, move the product outdoors as soon as possible, and then use a fire extinguisher to extinguish
shock, long time charge, or cable flames. Do not spray water or immerse the product in any situation, which can lead to more danger.
cover damage, discontinue use
immediately and contact the service D AN G ER 3. Lithium battery pack has very high energy density, so if you charge the battery for a long time and
center there is a case of short-circuit, leakage, bad battery, etc., it can lead to ignition.
Therefore, you should avoid charging for a long time without a person being present to avoid the risk of unexpected fire.
7. Use only genuine charger. 6) Misuse If the lithium battery is short-circuited, the polarity is changed, or if the battery is impacted,
8. Do not insert conductors into the charging port. malfunction or fire may result.
9. Do not touch the plug for about 10 seconds after unplugging the charger. There is a risk of If you think that the battery has been impacted, you should stop charging and using it and visit the
electric shock from instantaneous discharge. CAUTION nearest service center for inspection.
10. Do not remove the terminal during charging. Otherwise you may charge the internal circuit 7) Water inflow It should be controlled to prevent water inflow into the lithium battery.
of the charger and cause malfunction. There is a risk of fire or electric shock if the charger is connected while moisture is present.
11. Do not operate the product during charging. N O T ICE 8) Caution Disconnect the battery from the main unit except when recharging and reinstalling.
12. Charging terminals should be firmly contacted during charging and should not be used if Do not use for any other purpose.
terminals are corroded or damaged. DANGER 9) Disposal When disposing of the lithium battery, the battery should be separated from the product at
13. When disconnecting the charger from the product, it is safe to hold the terminal without the point of purchase or near the service center and the charge and discharge terminals are not short-
holding the wire. circuited. Dispose of it as industrial waste.
14. Be sure to keep the charger disconnected from the product after the charging is complete.
Battery disassembly prohibited
The charger must be disconnected if it is not used for longer than a few days, as there is a risk
Battery disassembly, modification, and repair are not covered under warranty.
of overcharging when charging more than the time indicated on the product specifications.

16 Dualtron XII User Manual 15 16 Dualtron XII User Manual 17

W AR N IN G
 3 5
PA 98 %
SET

Km/h

PA 98 %
SET

Km/h

PA 98 %

SET
0Safety guidelines 3before driving
SET SET
5
Check and Maintenance
1) Required checking before use
1. Check throttle and handle
• Operate the accelerator throttle lever about 2 ~ 3 times to check whether it returns Maintenance and self-maintenance
to the home position.
• Be careful that excessive throttle leaning and manipulation of the throttle can cause Electric products can be damaged by various factors.
malfunction due to internal parts damage.
The life span of each part varies depending on driving habits and driving
• Check for free gap in the handlebars before using.
environment.
2. Check brake and cable Parts that exceed the service life may cause accidents.Let's manage
• The brake braking force is sufficient to check the operating condition. various parts and prevent safety accidents in advance.
If the braking force is significantly lowered, use it immediately after inspection and action.
• Check that the brake pad is not worn, that the cable is not loose, that the cable is not damaged, and that
there is no leakage in the case of hydraulic brakes.
Check the replacement timing of consumable parts
• If there is an unusual feeling or noise during operation, check for breakage, wear, and
deformation of the inner wire of the brake cable. The components and suspension parts of the swing arm,tires,wheels,bear-
• Check that the bolts and nuts of the brake fixing parts are not loose and that the disc is
not deformed or damaged. ings,discs,brakepads,
cables and folding parts, various brackets and other consumable parts
3. Check tire pressure and abnormal tread wear
require periodic inspection
• Check the front and rear tires for wear and punctures and check the value marked on
the surface of the tire. and must always be checked.
When the air pressure is shortened, the possibility of puncture increases, so check
always.
• It is necessary to judge the replacement time by observing the appearance of the tire
such as tire damage, uneven wear.

4.Tightening check such as folding part and handle part

• Make sure that the bolts and nuts of all parts of the product are tight and safe from
loosening. Check the fastening condition and clearance of the folding and fixing
parts of the handle (folding knob, swing arm, etc. foldingDANGER
related parts, suspension
arm bolt, swing arm bolt).

* In these cases, stop driving immediately.

If you encounter any of the following situations while driving, stop driving
immediately and contact your nearest branch or service center for proper
measures.
W AR
If you provide pictures and videos to get an accurate diagnosis, professional counseling N IN G
is available.
ƽ Unusual heating of the motor ƽ Abnormal noise is generated
ƽ Brake braking status error ƽ Product smoke, ignition, sour odor
ƽ Error messages on the instrument panel
CAUTION
ƽ When rain or wet with water or in a similar situation
ƽ When the throttle is not returned to its original position ƽ When other driving is judged to be unreasonable
ƽ When the battery doesn't fully charge and shorter riding distance after a full charge
(Battery explosion may cause due to faulty battery cell or battery cell breakdown)
N O T ICE
18 Dualtron XII User Manual 17 18
 Important check list

* Metal vibration may occur due to motor vibration and the vibration of the brake
2. External damage inspection by driving environment CAUTION
disc and pad during the load
section that accelerates during driving. (About 15 ~ 30Km, different for each
① Replace parts that may be damaged by the external driving environ- product)
ment, such as deformation of parts or tiny cracks due to pressure. This is a phenomenon in which all rotations (fans, automobiles, ships, etc.) are
② Ifthe product is exposed to strong sunlight for a long time,discoloration vibrating at a specific rotational
may occur. frequency (rpm) rather than the product.
③Incase ofjumps, slightimpacts suchas turning, collision, etc.,whendriving- However, if the continuous noise or metal noise is large, there is a possibility that
frequently or for a long the disk will become bent
time in a poor road condition or driving for thousands of kilometers or and deformed.
more, fatigue breakdown * Please note that after running, there is a risk of burns due to the heat on the
phenomena may happen so please check the parts replacement schedule motor and brake (especially
for each product and replace accordingly for safety. disk rotor) side.
④ Fatigue breakdown and maintenance parts may differ from the example * Be careful that the bolts of the motor, rim, and motor shaft may become
conditions depending on the driving loosened due to the ABS function.
environment and the operating conditions. * For inspection and repair, remove the side cover, attach the power switch, and
Also check parts other than the attach it with the product's
replacement cycle (maintenance parts) standard bolt. When tightening, carefully remove the cover of the wiring. Bolts
at all times to check for any signs ofabnormality. other than the rule bolts (long
bolts) can cause serious damage to the battery casing (battery cells), which can
cause fire or safety accidents.
※ Folding parts and joints where movement occurs due to product characteris-
tics can naturally damage
the surface or paint surface during use, especially when operating in incorrect
operation and form.
※ When inspecting the product, keep two wheels away from the ground and
work on a safe workstation

19 20
MEMO MEMO

21 22