Global LCD Panel Exchange Center www.panelook.

com

LM270WF1
Liquid Crystal Display

Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ̻ ) Final Specification

Title 27” Full HD TFT LCD

BUYER LG Electronics SUPPLIER LG. Display Co., Ltd.

MODEL *MODEL LM270WF1

SUFFIX TLB1

*When you obtain standard approval,

please use the above model name without suffix

SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE

/ H.S. Kim / G.Manager

REVIEWED BY

/ D.I. Chung / Manager

PREPARED BY

/ K.H. Lee / Engineer

Please return 1 copy for your confirmation with MNT Products Engineering Dept.
your signature and comments. LG. Display LCD Co., Ltd

Ver 1.2 Feb, 04, 2009 1 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

Contents

No ITEM Page
COVER 1

CONTENTS 2

RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS 5

3 ELECTRICAL SPECIFICATIONS 6

3-1 ELECTRICAL CHARACTREISTICS 6

3-2 INTERFACE CONNECTIONS 8

3-3 SIGNAL TIMING SPECIFICATIONS 12

3-4 SIGNAL TIMING WAVEFORMS 13

3-5 COLOR INPUT DATA REFERNECE 14

3-6 POWER SEQUENCE 15

4 OPTICAL SFECIFICATIONS 17
5 MECHANICAL CHARACTERISTICS 23

6 RELIABLITY 26

7 INTERNATIONAL STANDARDS 27

7-1 SAFETY 27

7-2 EMC 27

8 PACKING 28

8-1 DESIGNATION OF LOT MARK 28

8-2 PACKING FORM 28

9 PRECAUTIONS 29

Ver 1.2 Feb, 04, 2009 2 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

RECORD OF REVISIONS

Revision
Revision Date Page Description
No
0.0 Oct. 1. 2008 - First Draft(Preliminary)
0.1 Oct. 15. 2008 4,6 Power consumption is updated.
Notes 6 is added
10
“On status of MPRT is support dynamic image.”
16 Signal Timing specification is changed.
Skew specification is updated.
0.2 Nov.1.2008 12
Skew : 350ps @85~90Mhz

1.0 Dec. 11. 2008 Final Specifications

Addedthe noted 5
16
5. BDI on status : Vsync opearte at 60hz
1.1 Jan.16..2009 19 T7 Timing Specification is changed from 500ms to 300ms.
1.2 Feb. 4. 2009 20 Add the Viewing angle specification at CR>5

Ver 1.2 Feb, 04, 2009 3 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

1. General Description
LM270WF1 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) backlight system without inverter. The matrix employs a-Si Thin Film Transistor as the active
element. It is a transmissive type display operating in the normally black mode. It has a 27 inch diagonally
measured active display area with Full HD resolution (1080 vertical by 1920 horizontal pixel array)
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
thus, presenting a palette of more than 16,7M colors with Advanced-FRC (Frame Rate Control). . It has
been designed to apply the interface method that enables low power, high speed, low EMI. FPD Link or
compatible must be used as a LVDS (Low Voltage Differential Signaling) chip. It is intended to support
applications where thin thickness, wide viewing angle, low power are critical factors and graphic displays are
important. It is intended to support displays where high brightness, super wide viewing angle,
high color saturation, and high color are important.

Source Driver Circuit

RGB, Dclk, DE Timing Control
Hsync, Vsync S1 S1920
CN1 Block
(LVDS 2 port) (30pin) Gate Driver circuit
G1

VLCD(12.0V)
TFT-LCD Panel
Power Circuit Block (1920 u 1080 pixels)
G1080

V LAMP CN 2 Back light Assembly

2pin x 8CNs (High)
(Direct Light Type_ U shape 7 CCFL)

Figure 1. Block diagram

General Features
Active Screen Size 27 inches(68.6cm) diagonal
Outline Dimension 630(H) x 368.2(V) x 37.2(D) mm(Typ.) *Without Inverter
Pixel Pitch 0.3114 mm x 0.3114 mm
Pixel Format 1920 horiz. By 1080 vert. Pixels RGB stripes arrangement
Color Depth 8-bit with A-FRC, 16,777,216 colors
Luminance, White 400 cd/m2 (Center 1 point)
Viewing Angle(CR>10) View Angle Free (R/L 170(Typ.), U/D 160(Typ.))
Power Consumption Total 87.8 Watt (Typ.) ( 4.2 Watt @VLCD, 83.6 Watt @400cd/༇])
Weight 4220 g (typ.)
Display Operating Mode Transmissive mode, normally White
Surface Treatment Hard coating(3H) & Anti-Glare treatment of the front polarizer

Ver 1.2 Feb, 04, 2009 4 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

2. Absolute Maximum Ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. ABSOLUTE MAXIMUM RATINGS

Values
Parameter Symbol Units Notes
Min Max
Power Input Voltage VLCD -0.3 12.4 Vdc at 25 r 2¶C

Operating Temperature TOP 0 50 ¶C

Storage Temperature TST -20 60 ¶C
1
Operating Ambient Humidity HOP 10 90 %RH

Storage Humidity HST 10 90 %RH

Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 ¶C Max, and no condensation of water.

‫ڀڋڔ‬

‫ڋڑ‬
‫ڀڋڑ‬

‫ڋڐ‬ ‫ۀۂڼۍۊۏڮ‬
‫ڸڣڭڄڀڃڶٻ۔ۏۄڿۄۈېڣ‬

‫ڽۇېڝٻۏۀڲ‬
‫ڸڞڶٻۀۍېۏڼۍۀۋۈۀگ‬
‫ڋڏ‬
‫ڀڋڏ‬
‫ۉۊۄۏڼۍۀۋڪ‬
‫ڋڎ‬

‫ڋڍ‬
‫ڋڌ‬
‫ڋ‬
‫ڀڋڌ‬

‫ڋڍڈ‬ ‫ڋ‬ ‫ڋڌ‬ ‫ڋڍ‬ ‫ڋڎ‬ ‫ڋڏ‬ ‫ڋڐ‬ ‫ڋڑ‬ ‫ڋڒ‬ ‫ڋړ‬

‫ڸڞڶٻۀۍېۏڼۍۀۋۈۀگٻڽۇېڝٻ۔ۍڟ‬

Figure 2. Temperature and relative humidity

Ver 1.2 Feb, 04, 2009 5 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and
liquid crystal. The second input power for the CCFL, is typically generated by an inverter. The inverter is an
external unit to the LCDs.

Table 2-1. ELECTRICAL CHARACTERISTICS

Values
Parameter Symbol Unit Notes
Min Typ Max
MODULE :
Power Supply Input Voltage VLCD 11.6 12.0 12.4 Vdc
Permissive Power Input Ripple VdRF 400 mVp-p 1
Differential Impedance Zm 90 100 110 Ohm
- Z\W [WZ mA 2
Power Supply Input Current ILCD
Normal - [`W \]\ mA 3
status Pc TYP - [UY [U_[ Watt 2
Power Consumption
Pc MAX - \U__ ^UWY Watt 3
- \WW \^\ mA 2
Power Supply Input Current ILCD
BDI - \XW \`W mA 3
Status Pc TYP - 6.0 6.9 Watt 2
Power Consumption
Pc MAX - 6.12 7.08 Watt 3

Rush current IRUSH - - 3.0 A 4

Note :
1. Permissive power ripple should be measured under VCC=12.0V, 25¶C, fV(frame frequency)=MAX
condition and At that time, we recommend the bandwidth configuration of oscilloscope is to be under
20Mhz. See the next page.

2. The specified current and power consumption are under the VLCD=12.0V, 25 r 2¶C,fV=60Hz condition
whereas Mosaic and max power pattern shown in the [ Figure 3 ] is displayed.

3. The current is specified at the maximum current pattern.

4. Maximum Condition of Inrush current :

The duration of rush current is about 2ms and rising time of Input Voltage is 1ms(min.).
At any rising time of Input voltage, Keep the I2T Value by below Condition
Condition : I2T < 32*2ms

Ver 1.2 Feb, 04, 2009 6 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

• Permissive Power input ripple (VCC=5.0V, 25¶C, fV(frame frequency)=MAX condition)

White pattern Black pattern

• Power consumption (VCC=5.0V, 25¶C, fV (frame frequency=60Hz condition)

Typical power Pattern Max power Pattern

Figure 3. Mosaic pattern & Black Pattern for power consumption measurement

Ver 1.2 Feb, 04, 2009 7 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

Table 2_2. ELECTRICAL CHARACTERISTICS

Values
Parameter Symbol Unit Notes
Min Typ Max
LAMP :
Operating Voltage VBL 1900(7.0mA) 1990(6.0mA) 2250(3.0mA) VRMS 1, 2
Operating Current IBL 3.0 6.0 7.0 mARMS 1
Established Starting Voltage Vs 1, 3
at 25 ¶C - - 3000 VRMS
at 0 ¶C - - 3600 VRMS
Operating Frequency fBL 40 - 80 kHz 4
Discharge Stabilization Time Ts 3.0 Min 1, 5
Power Consumption PBL 47.3 83.6 93.1 Watt 6
Life Time 40,000 Hrs 1, 7

Note : The design of the inverter must have specifications for the lamp in LCD Assembly.
The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by
the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully
designed so as not to produce too much leakage current from high-voltage output of the inverter.
When you design or order the inverter, please make sure unwanted lighting caused by the mismatch
of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD–
Assembly should be operated in the same condition as installed in you instrument.
୔ Do not attach a conducting tape to lamp connecting wire.
If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter
has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.

1. Specified values are for a single lamp.

2. Operating voltage is measured at 25 r 2¶C. The variance of the voltage is r 10%.
3. The voltage above VS should be applied to the lamps for more than 1 second for start-up.
(Inverter open voltage must be more than lamp starting voltage.)
Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current.
4. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may
cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal
synchronous frequency and from its harmonics in order to prevent interference.
5. Let’s define the brightness of the lamp after being lighted for 5 minutes as 100%.
TS is the time required for the brightness of the center of the lamp to be not less than 95%.
6. The lamp power consumption shown above does not include loss of external inverter.
The used lamp current is the lamp typical current. (PBL = VBL x IBL x NLamp )
7. The life is determined as the time at which brightness of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25 r 2¶C.

Ver 1.2 Feb, 04, 2009 8 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

8. The output of the inverter must have symmetrical(negative and positive) voltage waveform and
symmetrical current waveform (Unsymmetrical ratio is less than 10%). Please do not use the inverter
which has unsymmetrical voltage and unsymmetrical current and spike wave.
Requirements for a system inverter design, which is intended to have a better display performance, a
better power efficiency and a more reliable lamp, are following.
It shall help increase the lamp lifetime and reduce leakage current.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion rate of the waveform should be within ˲2 ·10%.
* Inverter output waveform had better be more similar to ideal sine wave.

* Asymmetry rate:
Ip
| I p – I –p | / Irms x 100%

* Distortion rate
I -p
I p (or I –p) / Irms

9. The inverter which is combined with this LCM, is highly recommended to connect coupling(ballast)
condenser at the high voltage output side. When you use the inverter which has not coupling(ballast)
condenser, it may cause abnormal lamp lighting because of biased mercury as time goes.
10.In case of edgy type back light with over 4 parallel lamps, input current and voltage wave form should
be synchronized

Ver 1.2 Feb, 04, 2009 9 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

3-2. Interface Connections

This LCD employs Two interface connections, a 30 pin connector is used for the module electronics and a
14Pin Connector is used for the integral backlight system.

3-2-1. LCD Module

- LCD Connector(CN1): KDF71G-30S-1H, (Manufactured by Hirose )

- Mating Connector : FI-X30C2L (Manufactured by JAE) or Equivalent

Table 3 MODULE CONNECTOR(CN1) PIN CONFIGURATION

u– z ”‰–“ kŒšŠ™—›–• u– z ”‰–“ z ”‰–“

1 ͷ΃͡; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑͑͡ͽ·͵΄͚ 16 ΄΃͢΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑͑͢ͽ·͵΄͚

2 ͷ΃͡΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑͑͡ͽ·͵΄͚ 17 ͸Ϳ͵ ͸ΣΠΦΟΕ

3 ͷ΃͢; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑͑͢ͽ·͵΄͚ 18 ΄΃ͣ; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑ͣ͑ͽ·͵΄͚

4 ͷ΃͢΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑͑͢ͽ·͵΄͚ 19 ΄΃ͣ΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑ͣ͑ͽ·͵΄͚

5 ͷ΃ͣ; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑ͣ͑ͽ·͵΄͚ 20 ΄ʹͽͼͺͿ; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΝΠΔΜ͑ΔΙΒΟΟΖΝ͙͑ͽ·͵΄͚

6 ͷ΃ͣ΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑ͣ͑ͽ·͵΄͚ 21 ΄ʹͽͼͺͿ΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΝΠΔΜ͑ΔΙΒΟΟΖΝ͙͑ͽ·͵΄͚

7 ͸Ϳ͵ ͸ΣΠΦΟΕ 22 ΄΃ͤ; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑ͤ͑ͽ·͵΄͚

8 ͷʹͽͼͺͿ; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΝΠΔΜ͑ΔΙΒΟΟΖΝ͙͑ͽ·͵΄͚ 23 ΄΃ͤ΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑ͤ͑ͽ·͵΄͚

ͳ͵ͺ͑ʹΠΟΥΣΠΝ͙͑͸Ϳ͵ͫ͑ΠΗΗ͑ͤͤ͟͝·ͫΠΟ͚͑
9 ͷʹͽͼͺͿ΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΝΠΔΜ͑ΔΙΒΟΟΖΝ͙͑ͽ·͵΄͚ 24 ;΁΃΅ ͿΠΥΖΤ͑ͥͦͧ͟͝
10 ͷ΃ͤ; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑ͤ͑ͽ·͵΄͚ 25 Ϳʹ ͿΠ͑ʹΠΟΟΖΔΥΚΠΟ

11 ͷ΃ͤ΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΠΕΕ͑ΔΙΒΟΟΖΝ͙͑ͤ͑ͽ·͵΄͚ 26 Ϳʹ ͿΠ͑ʹΠΟΟΖΔΥΚΠΟ

12 ΄΃͡; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑͑͡ͽ·͵΄͚ 27 DCR_OUT ͵ΪΟΒΞΚΔ͑ʹ͠΃͑ΠΦΥΡΦΥ

13 ΄΃͡΁ ΁ΝΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑͑͡ͽ·͵΄͚ 28 ΀͵ʹ ΀͵ʹ͑ʹΠΟΥΣΠΝ͙͑͸Ϳ͵ͫ͑ΠΗΗ͑ͤͤ͟͝·ͫΠΟ͚

14 ͸Ϳ͵ ͸ΣΠΦΟΕ 29 ·ͽʹ͵ ΁ΠΨΖΣ͑΄ΦΡΡΝΪ͑ͣ͜͢͟͡·

15 ΄΃͢; ;ΚΟΦΤ͑ΤΚΘΟΒΝ͑ΠΗ͑ΖΧΖΟ͑ΔΙΒΟΟΖΝ͙͑͑͢ͽ·͵΄͚ 30 ·ͽʹ͵ ΁ΠΨΖΣ͑΄ΦΡΡΝΪ͑ͣ͜͢͟͡·

Note: 1. All GND(ground) pins should be connected together and to Vss which should also be connected to
the LCD’s metal frame.
2. All VLCD (power input) pins should be connected together.
3. Input Level of LVDS signal is based on the IEA 664 Standard.
4, MPRT and ODC control does not turn on at same time.
5. BL is 100% diming at MPRT on status..
6. On status of MPRT is support dynamic image.
Rear view of LCM
#1 #30
#1 #30

KDF71G-30S-1H [ Figure 4 ] Connector diagram

Ver 1.2 Feb, 04, 2009 10 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

Table 4. REQUIRED SIGNAL ASSIGNMENT FOR Flat Link (TI:SN75LVDS83) Transmitter

Pin # Pin Name Require Signal Pin # Pin Name Require Signal
1 VCC Power Supply for TTL Input 29 GND Ground pin for TTL

2 D5 TTL Input (R7) 30 D26 TTL Input (DE)

3 D6 TTL Input (R5) 31 TX CLKIN TTL Level clock Input

4 D7 TTL Input (G0) 32 PWR DWN Power Down Input

5 GND Ground pin for TTL 33 PLL GND Ground pin for PLL

6 D8 TTL Input (G1) 34 PLL VCC Power Supply for PLL

7 D9 TTL Input (G2) 35 PLL GND Ground pin for PLL

8 D10 TTL Input (G6) 36 LVDS GND Ground pin for LVDS

9 VCC Power Supply for TTL Input 37 TxOUT3ు Positive LVDS differential data output 3

10 D11 TTL Input (G7) 38 TxOUT3ృ Negative LVDS differential data output 3

11 D12 TTL Input (G3) 39 TX CLKOUTు Positive LVDS differential clock output

12 D13 TTL Input (G4) 40 TX CLKOUTృ Negative LVDS differential clock output

13 GND Ground pin for TTL 41 TX OUT2ు Positive LVDS differential data output 2

14 D14 TTL Input (G5) 42 TX OUT2ృ Negative LVDS differential data output 2

15 D15 TTL Input (B0) 43 LVDS GND Ground pin for LVDS

16 D16 TTL Input (B6) 44 LVDS VCC Power Supply for LVDS

17 VCC Power Supply for TTL Input 45 TX OUT1ు Positive LVDS differential data output 1

18 D17 TTL Input (B7) 46 TX OUT1ృ Negative LVDS differential data output 1

19 D18 TTL Input (B1) 47 TX OUT0ు Positive LVDS differential data output 0

20 D19 TTL Input (B2) 48 TX OUT0ృ Negative LVDS differential data output 0

21 GND Ground pin for TTL Input 49 LVDS GND Ground pin for LVDS

22 D20 TTL Input (B3) 50 D27 TTL Input (R6)

23 D21 TTL Input (B4) 51 D0 TTL Input (R0)

24 D22 TTL Input (B5) 52 D1 TTL Input (R1)

25 D23 TTL Input (RSVD) 53 GND Ground pin for TTL

26 VCC Power Supply for TTL Input 54 D2 TTL Input (R2)

27 D24 TTL Input (HSYNC) 55 D3 TTL Input (R3)

28 D25 TTL Input (VSYNC) 56 D4 TTL Input (R4)

Notes : Refer to LVDS Transmitter Data Sheet for detail descriptions.

Ver 1.2 Feb, 04, 2009 11 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

LVDS Input characteristics

1. DC Specification

Description Symbol Min Max Unit Notes

LVDS Differential Voltage |VID| 100 600 mV -
LVDS Common mode Voltage VCM 0.6 1.8 V -
LVDS Input Voltage Range VIN 0.3 2.1 V -

2. AC Specification

Description Symbol Min Max Unit Notes

tSKEW -350 + 350 Ps 90MHz > Fclk ˻ 85MHz
LVDS Clock to Data Skew Margin tSKEW - 400 + 400 ps 85MHz > Fclk ˻ 65MHz
tSKEW - 600 + 600 ps 65MHz > Fclk ˻ 25MHz
LVDS Clock to Clock Skew Margin (Even to Odd) tSKEW_EO - 1/7 + 1/7 Tclk -
Maximum deviation
FDEV - ·3 % -
of input clock frequency during SSC
Maximum modulation frequency
FMOD - 200 KHz -
of input clock during SSC

Ver 1.2 Feb, 04, 2009 12 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

< Clock skew margin between channel >

Freq.

Fmax
mŠŒ•›Œ™ QGmkl}
Fcenter

Fmin

X
mtvk

Time

3. Data Format < Spread Spectrum >

1) LVDS 2 Port

< LVDS Data Format >

Ver 1.2 Feb, 04, 2009 13 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

2) LVDS 1 Port

RCLK+

RA+/- R3 R2 R1 R0 G0 R5 R4 R3 R2 R1 R0 G0 R5 R4

RB+/- G4 G3 G2 G1 B1 B0 G5 G4 G3 G2 G1 B1 B0 G5

RC+/- B5 B4 B3 B2 DE VSYNC HSYNC B5 B4 B3 B2 DE VSYNC HSYNC

RD+/- G7 G6 R7 R6 X B7 B6 G7 G6 R7 R6 X B7 B6

Previous (N-1)th Cycle Current (Nth ) Cycle Next (N+1)th Cycle

Ver 1.2 Feb, 04, 2009 14 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

Table 5. BACKLIGHT CONNECTOR PIN CONFIGURATION(CN1,CN2,CN3,CN4,CN5,CN6, CN7)

The backlight lamp connector is a model 1006-12102 (CN1/CN2/CN3/CN4/CN5/CN6/CN7) manufactured by C-NET.

The mating connector part number are 1006-66202 (manufactured by C-NET) or equivalent. The pin configuration for
the connector is shown in the table below.

Pin Symbol Description NOTES

1,2 HV High Voltage for Lamp 1

ͿΠΥΖ͑ͫ͑͑͢͟΅ΙΖ͑ΙΚΘΙ͑ΧΠΝΥΒΘΖ͑ΡΠΨΖΣ͑ΥΖΣΞΚΟΒΝ͑ΚΤ͑ΔΠΝΠΣΖΕ͑΃ΖΕ͠ΈΙΚΥΖ

<BACKLIGHT CONNECTOR DIAGRAM>

‫ګڨڜڧڈڰ‬

CN1
CN2
CN3
CN4
CN5
CN6
CN7

Ver 1.2 Feb, 04, 2009 15 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

3-3. Signal Timing Specifications

This is signal timing required at the input of the TMDS transmitter. All of the interface signal timing should be
satisfied with the following specifications for it’s proper operation.
Table 5. TIMING TABLE

ITEM Symbol Min Typ Max Unit Note

Period tCLK 11.76 13.89 15.38 ns

DCLK
Frequency - 65 72 90 MHz

Period tHP 1018 1088 1120 tCLK

Horizontal Valid tHV 960 960 960 tCLK

Horizontal Blank tHB 58 128 160

Hsync Frequency fH 64 66 88 KHz

Width tWH 18 32 48 tCLK

Horizontal Back Porch tHBP 20 48 64

Horizontal Front Porch tHFP 20 48 48

Period tVP 1087 1100 1250 tHP

Vertical Valid tVV 1080 1080 1080 tHP

Vertical Blank tVB 7 20 170 tHP

Vsync Frequency fV 50 60 75 Hz

Width tWV 1 4 42 tHP

Vertical Back Porch tVBP 5 8 64

Vertical Front Porch tVFP 1 8 64

Note: Hsync period and Hsync width-active should be even number times of tCLK. If the value is odd number
times of tCLK, display control signal can be asynchronous. In order to operate this LCM a Hsync,
Vsyn, and DE(data enable) signals should be used.
1. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rates.
2. Vsync and Hsync should be keep the above specification.
3. Hsync Period, Hsync Width, and Horizontal Back Porch should be any times of of character
number(8).
4. The polarity of Hsync, Vsync is not restricted.
5. BDI on status : Vsync opearte at 60hz

Ver 1.2 Feb, 04, 2009 16 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

3-4. Signal Timing Waveforms

0.7VDD
Hsync, Vsync, DE, DATA
0.3VDD

tCLK
0.5VDD

Dclk
VALID

INVALID INVALID
DATA

DE(Data Enable)

Data are latched at the falling edge of DCLK

tHP
Hsync tWH

tHBP tHV tHFP

DE(Data Enable)
tVP
tWV
Vsync
tVBP tVV tVFP

DE(Data Enable)

Ver 1.2 Feb, 04, 2009 17 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

3-5. Color Data Reference

The Brightness of each primary color(red,green,blue) is based on the 8-bit gray scale data input for the color;
the higher the binary input, the brighter the color. The table below provides a reference for color versus data
input.

Table 6. COLOR DATA REFERENCE

Input Color Data

RED GREEN BLUE

Color
MSB LSB MSB LSB MSB LSB

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Green (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

Basic Blue (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Color Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

RED (000) Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED ... ... ... ...

RED (254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

RED (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (000) Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0

GREEN ... ... ... ...

GREEN (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0

GREEN (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

BLUE (000) Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1

BLUE ... ... ... ...

BLUE (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0

BLUE (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Ver 1.2 Feb, 04, 2009 18 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

3-6. Power Sequence

90% 90%

Power supply for LCD 10% 10%

Vcc
0V
T1 T2 T5 T7
Interface signal Valid data
VI

T8 T9
Option siganl
(ODC)
T3 T4

Power for LAMP Lamp on

OFF OFF

Table 7. POWER SEQUENCE

Values
Parameter Units
Min Typ Max

T1 0.5 - 10 ms

T2 0.01 - 50 ms

T3 500 - - ms

T4 200 - - ms

T5 0.01 - 50 ms

T7 300 - ms

T8 0 < T8 < T2 ms

T9 0 < T9 < T5 ms

Notes : 1. Please avoid floating state of interface signal at invalid period.

2. When the interface signal is invalid, be sure to pull down the power supply for LCD VLCDto 0V.
3. Lamp power must be turn on after power supply for LCD and interface signal are valid.

Ver 1.2 Feb, 04, 2009 19 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

4. Optical Specifications
Optical characteristics are determined after the unit has been ‘ON’ for approximately 30 minutes
in a dark environment at 25·2¶C. The values specified are at an approximate distance 50cm from the LCD
surface at a viewing angle of ) and T equal to 0 ¶ and aperture 1 degree.
FIG. 1 presents additional information concerning the measurement equipment and method.

Pritchard 880 or
LCD Module
Optical Stage(x,y) equivalent

50cm
FIG. 6 Optical Characteristic Measurement Equipment and Method

Table 9. OPTICAL CHARACTERISTICS (Ta=25 ¶C, VLCD=12.0V, fV=60Hz Dclk=144MHz, IBL=6mA)

Values
Parameter Symbol Units Notes
Min Typ Max
Contrast Ratio CR 700 1000 1
Surface Luminance, white LWH 320 400 cd/m2 2
Luminance Variation G WHITE 75 % 3
Rise Time TrR - 1 4 ms 4
Decay Time TrD - 4 8 ms 4
Response Time
Gray to Gray TGTG 2 6 ms 5
MPRT TMPRT 10 15 ms 6
RED Rx 0.661
Ry 0.318
GREEN Gx 0.207
Color Coordinates Gy Typ 0.668 Typ
[CIE1931] BLUE Bx -0.03 0.144 +0.03
By 0.068
WHITE Wx 0.313
Wy 0.329
Viewing Angle (CR>5)
x axis, right(I=0¶) Tr 75 88 Degree 7
x axis, left (I=180¶) Tl 75 88
y axis, up (I=90¶) Tu 70 85
y axis, down (I=270¶) Td 70 85
Viewing Angle (CR>10)
x axis, right(I=0¶) Tr 70 85 Degree 7
x axis, left (I=180¶) Tl 70 85
y axis, up (I=90¶) Tu 60 75
y axis, down (I=270¶) Td 70 85
Gray Scale 2.2 8

Ver 1.2 Feb, 04, 2009 20 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

Notes 1. Contrast Ratio(CR) is defined mathematically as :

Surface Luminance with all white pixels

Contrast Ratio =
Surface Luminance with all black pixels
2. Surface luminance is luminance value at No.1 point across the LCD surface 50cm
from the surface with all pixels displaying white. For more information see FIG 6.

3. The variation in surface luminance , G WHITE is defined as :

Minimum(Lon1 , L on2 , }.. L on9 )

GWHITE u 100(%)
Maximum (L on1 , L on2 , .... L on9 )

Measuring point for surface luminance & measuring point for luminance variation

A
H/10

2 3 4

V 6
5 1

7 8 9
V/10

A : H/4 mm Active Area

B : V/4 mm
@ H,V : Active Area

[ FIGURE 7 ] Measure Point for Luminance

Ver 1.2 Feb, 04, 2009 21 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

4. The response time is defined as the following figure and shall be measured by switching
the input signal for “black” and “white”.
Response time is the time required for the display to transition from white to black (Rise Time,
TrR) and from black to white (Decay Time, TrD).

% TrR TrD

100
90
Optical
white black white
response
10
0

[ FIGURE 8] Response Time

5, The gray to gray response time is defined as the following figure and shall be measured by switching
the input signal for “Gray To Gray”.
- Gray step : 5 step
- TGTG_AVR is the total average time at rising time and falling time for “Gray To Gray”.
- TGTG_MAX is the max time at rising time or falling time for “Gray To Gray”.

Table 10. Gray to gray response time table

Rising Time
Gray to Gray
G255 G191 G127 G63 G0
G255
G191
Falling Time G127
G63
G0

Ver 1.2 Feb, 04, 2009 22 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

6. MPRT is defined as the 10% to 90% blur-edge width Bij(pixels) and scroll speed U(pixels/frame)
at the moving picture.

MPRT is defined as 10% to 90% blur-edge with Bij(pixels) and scroll speed U(pixels/frame)at the moving
picture.

‫ۅڧ‬
1 90%
M= Bij (i=j)
U
Example) Bij = 12pixels, U = 10pixels / 120Hz
M = 12pixels / (10pixels / 120Hz) 10%
= 12pixels / {10pixels / (1/120)s} ‫ۄڧ‬
= 12 / 1,200 s Bij
= 10 ms

[ FIGURE 9] MPRT

Ver 1.2 Feb, 04, 2009 23 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

7. Viewing angle is the angle at which the contrast ratio is greater than 10 or 5. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis
which is normal to the LCD surface. For more information see FIG. 9 .

<Dimension of viewing angle range>

Normal
E Y
I = 90q, Up

I = 180q, Left
T

I = 0q, Right

I = 270q, Down

[ FIGURE 10 ] Viewing angle

8, Gray scale specification

Gamma Value is approximately 2.2. For more information see Table 11
Table 11. Gray Scale Specification

Gray Level Relative Luminance [%] (Typ.)

0 0.1

31 1.2

63 4.7

95 11.7

127 21.2

159 35.2

191 53.0

223 75.4

255 100

Ver 1.2 Feb, 04, 2009 24 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

5. Mechanical Characteristics
The contents provide general mechanical characteristics. In addition the figures in the next page are detailed
mechanical drawing of the LCD.

Horizontal 630mm

Outline Dimension Vertical 368.2mm

Depth 37.2mm

Horizontal 602mm
Bezel Area
Vertical 340.4mm

Horizontal 597.89mm
Active Display Area
Vertical 336.31mm

Weight Typ : 4220 g , Max : 4430 g

Hard coating(3H)
Surface Treatment
Anti-glare treatment of the front polarizer

Notes : Please refer to a mechanic drawing in terms of tolerance at the next page.

Ver 1.2 Feb, 04, 2009 25 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

<FRONT VIEW>

Ver 1.2 Feb, 04, 2009 26 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

<REAR VIEW>

Ver 1.2 Feb, 04, 2009 27 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

6. Reliability
Environment test condition

No Test Item Condition

1 High temperature storage test Ta= 60¶C 240h

2 Low temperature storage test Ta= -20¶C 240h

3 High temperature operation test Ta= 50¶C 50%RH 240h

4 Low temperature operation test Ta= 0¶C 240h

Wave form : random

Vibration level : 1.0Grms
Vibration test
5 Bandwidth : 10-300Hz
(non-operating)
Duration : X,Y,Z, 10min
One time each direction
Shock level : 100G
Shock test Waveform : half sine wave, 2ms
6
(non-operating) Direction : ᇹX, ᇹY, ᇹZ
One time each direction

7 Humidity condition Operation Ta= 40 ¶C ,90%RH

Altitude
8
storage / shipment 0 - 40,000 feet(12192m)

Maximum Storage Humidity for

9 Max 70%RH , Ta=40୅
4 corner light leakage Mura.

Ver 1.2 Feb, 04, 2009 28 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

7. International Standards

7-1. Safety
a) UL 60950-1:2003, First Edition, Underwriters Laboratories, Inc.,
Standard for Safety of Information Technology Equipment.
b) CAN/CSA C22.2, No. 60950-1-03 1st Ed. April 1, 2003, Canadian Standards Association,
Standard for Safety of Information Technology Equipment.
c) EN 60950-1:2001, First Edition,
European Committee for Electro technical Standardization(CENELEC)
European Standard for Safety of Information Technology Equipment.

7-2. EMC

a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),
1992
b) C.I.S.P.R. “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ International Special Committee on Radio Interference.
c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.“ European Committee for Electro technical Standardization.(CENELEC), 1998
( Including A1: 2000 )

Ver 1.2 Feb, 04, 2009 29 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification
8. Packing

8-1. Designation of Lot Mark

a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010

Mark 1 2 3 4 5 6 7 8 9 0

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 3 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one box : 5EA

b) Box Size : 747X335X466

Ver 1.2 Feb, 04, 2009 30 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

9. PRECAUTIONS

Please pay attention to the followings when you use this TFT LCD module.

9-1. MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=·200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it causes metallic foreign material and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.

Ver 1.2 Feb, 04, 2009 31 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
 Global LCD Panel Exchange Center www.panelook.com

LM270WF1
Liquid Crystal Display

Product Specification

9-3. ELECTROSTATIC DISCHARGE CONTROL

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE

Strong light exposure causes degradation of polarizer and color filter.

9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5¶C and 35¶C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM

(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-
blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-
hexane.

Ver 1.2 Feb, 04, 2009 32 / 32

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com