PROPOSED TWO STORIED INDUSTRIAL BUILDING OF EI LOCATION HUT.

Project - Two Storied Industrial Building

Project No - DGS_3402
Design Considerations :
Type of Structure R.C.C. FRAME
Grade of Concrete M 25

Grade of Steel Fe 500

Location of Structure - GUWAHATI
Seismic Information-
Zone - V
Zone Factor- 0.36
Response reduction factor - 5
Importance factor - 1
Rock/ soil site factor - 2
Type of structure - 1
Damping ratio - 0.05
Depth of foundation- 1.5 m
Design Assumption-
20 % of external brick work considered as opening for window/door.
10 % of internal brick work considered as opening for window/door.
Design Method-
The structure is designed as a continuous frame and in limit state method.

References :
IS 456
Design Aids to IS 456 ( SP 16 )
IS 875 ( Part 1, Part 2, Part 3 )
IS 1893
Clear Cover For :
Slab - 20 mm Ref -table-16a - is-456
Column - 40 mm
Beam- 25 mm
Foundation = 50 mm Ref -cl-26.4 /pg-46 - is-456
Lap Length -
For Tension - 50d d= Dia of bar
For Compression - 40d d= Dia of bar
Soil Information:
Active earth pressure co-efficient(Ka)= 1
Bulk density of Soil= 1.8 T/m2
Unit weight of water= 1 T/m2

Software used:
Autocad 2013
Staad Pro v8i SS6
MS excel 2016
Project No - DGS_3402

Structural Informations -

Depth of Foundation = 1.5 m Below G.L

Plinth height = 0.6 m
Ground Floor Height = 3.6 m
1st Floor Height = 3.6 m
Mumpty Room height = 2.5 m
Parapet wall Height- 1.1 m
Parapet wall above stair Roof - 0.5 m
Total Height of Building - 7.8 m G.F to Roof
Opening at Verandha - 0.75 m
Staad Level:-

Ground level = 0 m R.L

Founding Level = -1.5 m Below G.L Fixity Level = -0.8 m R.L
Tie /Grade Beam Level = 0 m Below G.L Grade Beam Level = 0 m R.L
First Floor = 4.2 m Above G.L First Floor level = 4.2 m R.L
Roof Level = 7.8 m Above G.L Roof Level = 7.8 m R.L
Mumpty Room = 10.3 m Above G.L Mumpty Room = 10.3 m R.L

Outer wall tkickness = 0.25 m Load Consideration :-

Outer wall tkickness = 0.25 m Dead Load:-(Unit Weight)
2
Partition wall Thickness = 0.125 m R.C.C = 24.2 KN/m
Partition wall Thickness = 0.125 m (Reinforcement <1% Steel)
2
Parapet wall thickness = 0.125 m R.C.C = 25 KN/m
Parapet wall above roof = 0.125 m (Reinforcement 1% -2% Steel)
2
Av. Depth of Beam = 0.35 m Floor Finish = 24 KN/m
2
Brick Masonry = 20 KN/m
2
Building Height = h 10.3 m Marble Finish = 26.5 KN/m
2
Width = w 13.3 m Lime Terracing = 22 KN/m
2
Length = L 5.3 m Partition wall = 1.33 KN/m
Imposed load:-(Unit Weight)
2
Px= 0.09xh/ √ d = 0.254 Floor = 5 KN/m
2
Pz= 0.09xh/ √ D = 0.403 Stair = 4 KN/m
2
Roof = 2 KN/m
2
Stair Roof = 0.75 KN/m
Project No - DGS_3402

FLOOR LEV. DL LL FLOOR LOAD (DL) FLOOR LOAD (LL)

1 4.2 4.94 2 YRANGE 4.2 4.2 FLOAD -4.94 GY YRANGE 4.2 4.2 FLOAD -2 GY
R 7.8 6.28 1.5 YRANGE 7.8 7.8 FLOAD -6.28 GY YRANGE 7.8 7.8 FLOAD -1.5 GY
M 10.3 6.28 0.75 YRANGE 10.3 10.3 FLOAD -6.28 GY YRANGE 10.3 10.3 FLOAD -0.75 GY

SL FL. WEIGHT(DL) SL FL. WEIGHT(LL)

YRANGE 4.2 4.2 FLOAD 4.94 YRANGE 4.2 4.2 FLOAD 0.5

YRANGE 7.8 7.8 FLOAD 6.28 YRANGE 7.8 7.8 FLOAD 0.375
YRANGE 10.3 10.3 FLOAD 6.28 YRANGE 10.3 10.3 FLOAD 0.188
Project No - DGS_3402
CONSIDERATION OF LOADS IN STAAD-PRO ANALYSIS:-
LOAD-1 ( Seismic load )
1 Seismic load in X – directions - computed by computer automatically.
LOAD-2 ( Seismic load )
2 Seismic load in Z – directions - computed by computer automatically.
3.D.L
a) Self wt. of beam and columns - computed by computer automatically.

For 1st Floor

b) Floor load
Slab Thickness = 0.15 m
2
Wt. of 0.15 thk. slab = 0.15 x 24.2 = 3.63 KN/m
2
Wt. of Ceiling Plaster = 0.25 KN/m
2
Wt. of floor finish = 0.04 x 26.5 = 1.06 KN/m
Wt. of light partirion Wall = KN/m2
2
4.94 KN/m
For Roof
c) Floor load
Slab Thickness = 0.15 m
Wt. of 0.15 thk. slab = 0.15 x 24.2 = 3.63 KN/m2
Wt. of Ceiling Plaster = 0.25 KN/m2
Wt. of Partion Wall = 0 KN/m2
Wt. of 100 thk. lime terracing = 0.1x24= 2.4 KN/m2
6.28
d ) Brick wall Load
Ground Floor
Plinth Load - (0.6x0.250x20) 3 Kn/m
Outer wall without Plinth - (3.6-0.35)x0.25x20 16.25 Kn/m 20% Reduce For opening 13.00
Inner Partition wall without Plinth = (3.6-0.35)x0.125x20 8.13 Kn/m 10% Reduce For opening 7.31
Wall load below Landing - (3.6/2-0.35)x0.25x20 7.25 Kn/m

e) Ist Floor
Weight of 250 thk Outer wall = (3.6-0.35)x0.25x20 16.25 Kn/m 20% Reduce For opening 13.00
Inner Partition wall without Plinth = (3.6-0.35)x0.125x20 8.13 Kn/m 10% Reduce For opening 7.31
Weight of hulf landing= (3.6-0.35)x0.25x20 16.25 KN/m 25% Reduce For opening 12.19
f) At roof
Weight of Parapet Wall = 1.1 x 0.125 x 20= 2.75 KN/m
Weight of Parapet Wall over stair roof = 0.5X0.125X20= 1.25 KN/m
Wall Load of 2.5 m height at stair . (2.5 -0.35 ) x 0.25X 20= 10.75 Kn/m
Weight of 250 thk. Wall over Last Landing = ((3.6/2+2.4)-0.35)x0.25x20 19.75 KN/m 25% Reduce For opening 14.81
g) For Stair
Due to Dead Load :-
Load on full Landing - 12.76 KN/m
Load on Half landing 17.25 KN/m
Due to Live Load :-
Load on full Landing - 6.48 KN/m
Load on Half landing 9.72 KN/m
Project No - DGS_3402

4. L.L.
a) Floor Load. 5 KN/m2
b) Roof Load . 2 KN/m2
c) Stair Roof Load . 0.75 KN/m2
d) Stair Load . 4 KN/m2

DEAD LOAD OF O.H.W.T.

Water Tank capacity 2000 Litres
Water Load 2T 19.6 KN
L (m) B (m)
SIZE 4.05 2.8
Bottom slab Thk. 0.125
Botttom slab Wt. 4.05x2.8x0.125x 25 35.44 Kn
P.V.C Water tank weight = 0.59 Kn
Weight of water = 19.6 Kn
Total Weigt due to water tank . = 55.63 Kn
Load on each node = 55.63/4 13.91 kN
Project No - DGS_3402

Design of Waist Slab -

W2 W1
W1 8.295 KN/m
5.54 KN/m 5.54 KN/m
FULL
A 0.15 2.75 1.15 B HALF
4.05

Riser = 150 mm Tread = 250 mm

Slope factor = 1.17
Assume Waist Slab Thickness = 175 mm
Wt of 175 thk slab on Slope = ( 175 / 1000 ) x 24.2 = 4.24 KN/m2
Wt of 175 thk slab on Plan = 1.17 x 4.24 = 4.96 KN/m2
Wt of Ceiling Finishes on Slope = 0.24 KN/m2
Wt of Ceiling Finishes on Plan = 0.24 x 1.17 = 0.28 KN/m2
Wt of Top finishes on Slope = 1.06 KN/m2
Wt of Top finishes on Plan = 1.06 x 1.17 = 1.24 KN/m2
Wt of Steps = 1.82 KN/m2
Live Load = 3.00 KN/m2
Unit Weight at Landing portion = 5.54 KN/m2
Unit Weight at Going portion = 8.30 KN/m2

Considering Simply Supported Slab =

RA = [ 5.54 x 0.15 x { 3.9 + ( 0.5 x 0.15 ) } + { 8.295 x 2.75 x (1.15 + ( 0.5 x 2.75 )) } +
{(5.54 x 1.15) x (0.5 x 1.15 ) ] / 4.05
= 15.94 KN
RB = ( 5.54 x 0.15 ) + ( 8.295 x 2.75 ) + ( 5.54 x 1.15 ) - 15.94
= 14.07 KN

Assume Maximum Moment occurs at a distance Y from Support B

Moment at a distance x from Sopport B = { 14.07 x Y } - { 8.295 x (Y-1.15)x (Y-1.15)/2) }-{ 5.54 x 1.15x (Y-1.15/2) }
If the Moment is Maximum at a distance Y from Support B , then the Shear Force at this point = 0
14.07 +3.21- ( 8.295 x Y ) = 0
Y= ( 17.28 / 8.295 ) = 2.08 m from Support B

Hence , Maximum Span Moment for D.L considering Simply Supported Slab =
= { 14.07 x 2.08 } - { 8.295 x (2.08-1.15)x (2.08-1.15)/2) }-{ 5.54 x 1.15x (2.08-1.15/2) }
= 16.09 KNm /m width
Maximum Span Moment due to D.L considering Continuous Slab = ( 0.8 x 16.09 )
= 12.872 KNm/m width

Considering Continuous slab

RA = 15.94 - ( 12.872 / 4.05 ) = 12.76 KN for D.L only
RB = 14.07 + ( 12.872 / 4.05 ) = 17.25 KN for D.L only

Consideration for L.L - W1 = W2 = 4 KN/m /m width

Project No - DGS_3402

Design of Waist Slab -

Considering Simply Supported Slab RA = R B = 4 x 4.05 / 2 = 8.1 KN

Maximum Span Moment due to L.L considering Simply Supported Slab =
4 x (4.05 x 4.05 / 8 ) = 8.2 KNm / m width

Maximum Span Moment due to L.L considering Continuous Slab =

( 0.8 x 8.2) = 6.56 KNm / m width
Considering Continuous Slab ,
RA = 8.1 - ( 6.56 / 4.05 ) = 6.48 KN
RB = 8.1 + ( 6.56 / 4.05 ) = 9.72 KN

Ast at Span and Support -

Maximum Span Moment (D.L + L.L ) = ( 12.872 + 6.56 ) = 19.432 KNm / m width
Effective Depth of Section = ( 175 - 20 - 6 ) = 149 mm
2
Mu/bd2 = ( 1.5 x 19.432 x 1000000 ) / ( 1000 x 149 x 149 ) = 1.31 N/mm
Ref - Table -2 SP-16 , pt = 0.33
2
Ast = ( 0.326 x 1000 x 149 ) / 100 = 485.74 mm

Spacing of steel required for = 12 T 232.63474 mm c/c

10 T 162.63845 mmc/c
Slab Thickness = 175 mm
Provide 12 T @ 150 mm C/C
Provide 10 T @ 150 mm C/C Distribution Steel.

Check for Deflection :-

Depth of Slab = 175 mm

Effective depth of slab = 149 mm

fs= 0.58fy area of cross section of steel required

area of cross section of steel provided

Area of cross section of steel required = 486 mm2

Area of cross section of steel provided = 754 mm2

fs= =0.58x500x(486/754) = 186.923

Percentage of tension Reinforcement = 0.51 %
M.F. = 1.55 (Fig. 4, IS -456-2000, Pg . -38 )

Span to Depth ratio = =4050/149 27.2

Permissible Span to Depth ratio = =20x1.55 40.3 > provided o.k.

Stair Load (Left Side Stair )
D.L.
Load due to stair at Full landing = 12.76 Kn/m
Load on stair at Half landing = 17.25 Kn/m

LL
Load due to stair at Full landing = 6.48 Kn/m
Load due to stair at Half landing = 9.72 Kn/m
PROPOSED TWO STORIED INDUSTRIAL BUILDING OF EI LOCATION HUT.
TWO STORIED INDUSTRIAL BUILDING
CALCULATIONS -
DGS_3402 / STR / UCC24_02 / UCC / NFR / 171224 / Report/ Dwg / DEC 24
LOCAION - KALIAGAUNJ
ZONE = V
ZONE FACTOR (Z ) = 0.36
IMPORTANCE FACTOR ( I ) = 1
RESPONSE REDUCTION FACTOR ( R ) = 5
BUILDING INFORMATION -

Z DIRECTION
X- DIRECTION
LENGTH = 5.3 M

WIDTH = 13.3 M

HEIGHT OF BUILDING = 22.55 M

TIME PERIOD ( Tz ) = [{ 0.09 x 22.55 } / SQRT( 13.3 )] = 0.56

REF - IS -1893 P-1 / 2016 - FIG -2 Sa/g = 2.4
Ahx = [ (Z/2) x ( I / R ) x (Sa/g) ] = [( 0.36 /2 ) x ( 1 / 5 ) x 2.4 ] = 0.0864

TIME PERIOD ( Ty ) = [{ 0.09 x 22.55 } / SQRT( 11.95 )] = 0.59

REF - IS -1893 P-1 / 2016 - FIG -2 Sa/g = 2.3
Ahx = [ (Z/2) x ( I / R ) x (Sa/g) ] = [( 0.36 /2 ) x ( 1 / 5 ) x 2.3 ] = 0.083

TIME PERIOD ( Tx ) = [{ 0.09 x 22.55 } / SQRT( 5.3 )] = 0.88

REF - IS -1893 P-1 / 2016 - FIG -2 Sa/g = 1.5
Ahz = [ (Z/2) x ( I / R ) x (Sa/g) ] = [( 0.36 /2 ) x ( 1 / 5 ) x 1.5 ] = 0.054
STAAD INPUT FILE

STRUCTURAL DESIGN DOCUMENTATION OF PROPOSED TWO STORIED INDUSTRIAL

BUILDING OF EI LOCATION HUT.

STAAD SPACE DXF IMPORT OF EI LOCATION HUT.DXF

START JOB INFORMATION
JOB NAME TWO STORIED INDUSTRIAL BUILDING
JOB CLIENT EI LOCATION HUT
JOB NO DGS_3402
JOB REV 1
ENGINEER NAME JM
ENGINEER DATE 1/25/2025
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 13.05 0 0; 3 13.05 0 5.05; 4 0 0 5.05; 6 6.575 0 5.05; 7 3.775 0 0;
8 3.775 0 5.05; 9 9.275 0 0; 10 9.275 0 5.05; 11 9.275 0 4.05; 12 13.05 0 4.05;
13 3.775 0 1.475; 14 9.275 0 1.475; 15 3.775 0 3.575; 16 9.275 0 3.575;
17 8.025 0 0; 18 8.025 0 5.05; 20 9.275 4.2 0; 21 13.05 4.2 0;
22 13.05 4.2 5.05; 25 6.575 4.2 5.05; 26 3.775 4.2 0; 27 3.775 4.2 5.05;
28 9.275 4.2 5.05; 29 9.275 4.2 4.05; 30 13.05 4.2 4.05; 31 5.86e-14 4.2 3.8;
32 9.275 4.2 3.8; 34 9.275 7.8 0; 35 13.05 7.8 0; 36 13.05 7.8 5.05;
39 6.575 7.8 5.05; 40 3.775 7.8 0; 41 3.775 7.8 5.05; 42 9.275 7.8 5.05;
43 9.275 7.8 4.05; 44 13.05 7.8 4.05; 45 5.86e-14 7.8 3.8; 46 9.275 7.8 3.8;
47 9.275 10.3 0; 48 13.05 10.3 0; 49 13.05 10.3 5.05; 50 9.275 10.3 5.05;
51 9.275 10.3 2.525; 52 13.05 10.3 2.525; 53 0 -1.5 0; 54 3.775 -1.5 0;
55 6.575 -1.5 7.99e-14; 56 6.575 0 7.99e-14; 57 9.275 -1.5 0; 58 13.05 -1.5 0;
59 0 -1.5 5.05; 60 3.775 -1.5 5.05; 61 6.575 -1.5 5.05; 62 9.275 -1.5 5.05;
63 13.05 -1.5 5.05; 64 0 4.2 0; 65 6.575 4.2 7.99e-14; 66 0 4.2 5.05;
67 0 7.8 0; 68 6.575 7.8 7.99e-14; 69 0 7.8 5.05; 70 13.05 2.4 0;
71 9.275 2.4 0; 72 13.05 6 0; 73 9.275 6 0; 74 6.575 0 3.575; 75 6.575 0 1.475;
76 8.025 0 1.475; 77 8.025 0 3.575; 78 6.575 4.2 3.8; 79 3.775 4.2 3.8;
80 6.575 7.8 3.8; 81 3.775 7.8 3.8; 82 9.275 10.9 0; 83 13.05 10.9 0;
84 9.275 10.9 2.525; 85 13.05 10.9 2.525;
MEMBER INCIDENCES
1 1 7; 2 2 12; 3 3 10; 4 4 1; 5 56 75; 6 7 13; 7 9 14; 8 11 12; 9 13 75;
10 15 74; 11 17 76; 12 64 26; 13 21 30; 14 22 28; 15 66 31; 16 65 78; 17 26 79;
18 20 32; 19 29 30; 20 31 79; 21 67 40; 22 35 44; 23 36 42; 24 69 45; 25 68 80;
26 40 81; 27 34 46; 28 43 44; 29 45 81; 30 47 48; 31 48 52; 32 49 50; 33 47 51;
34 51 52; 35 53 1; 36 54 7; 37 55 56; 38 57 9; 39 58 2; 40 59 4; 41 60 8;
42 61 6; 43 62 10; 44 63 3; 45 34 47; 46 35 48; 47 42 50; 48 36 49; 49 1 64;
50 7 26; 51 56 65; 52 9 71; 53 2 70; 54 4 66; 55 8 27; 56 6 25; 57 10 28;
58 3 22; 59 64 67; 60 26 40; 61 65 68; 62 20 73; 63 21 72; 64 66 69; 65 27 41;
66 25 39; 67 28 42; 68 22 36; 69 70 71; 70 72 73; 71 9 2; 72 17 9; 73 56 17;
74 7 56; 75 12 3; 76 8 4; 77 6 8; 78 18 6; 79 10 18; 80 74 6; 81 75 74;
82 15 8; 83 13 15; 84 11 10; 85 16 11; 86 14 16; 87 76 14; 88 75 76; 89 77 16;
90 74 77; 91 77 18; 92 76 77; 93 65 20; 94 26 65; 95 30 22; 96 27 66; 97 25 27;
98 28 25; 99 31 64; 100 78 25; 101 79 27; 102 29 28; 103 32 29; 104 78 32;
105 79 78; 106 68 34; 107 40 68; 108 44 36; 109 41 69; 110 39 41; 111 42 39;
112 45 67; 113 80 39; 114 81 41; 115 43 42; 116 46 43; 117 80 46; 118 81 80;
119 52 49; 120 51 50; 121 71 20; 122 70 21; 123 73 34; 124 72 35; 125 47 82;
126 48 83; 127 51 84; 128 52 85; 129 82 83; 130 83 85; 131 85 84; 132 84 82;
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.17185e+07
POISSON 0.17
DENSITY 23.5616
ALPHA 1e-05
DAMP 0.05
TYPE CONCRETE
STRENGTH FCU 27579
END DEFINE MATERIAL
MEMBER PROPERTY AMERICAN
12 TO 29 69 70 93 TO 118 129 TO 132 PRIS YD 0.35 ZD 0.25
30 32 34 PRIS YD 0.3 ZD 0.25
MEMBER PROPERTY AMERICAN
1 TO 11 71 TO 92 PRIS YD 0.35 ZD 0.25
35 TO 37 40 TO 42 49 TO 51 54 TO 56 59 TO 61 64 TO 66 PRIS YD 0.35 ZD 0.4
127 128 PRIS YD 0.3 ZD 0.3
MEMBER PROPERTY AMERICAN
38 39 43 TO 48 52 53 57 58 62 63 67 68 121 TO 126 PRIS YD 0.35 ZD 0.5
MEMBER PROPERTY AMERICAN
31 33 119 120 PRIS YD 0.35 ZD 0.35
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
53 TO 55 57 TO 63 FIXED
MEMBER RELEASE
8 START MX MY MZ
8 END MX MY MZ
90 START MX MY MZ
89 END MX MY MZ
88 START MX MY MZ
87 END MX MY MZ
10 START MX MY MZ
10 END MX MY MZ
9 START MX MY MZ
9 END MX MY MZ
11 START MX MY MZ
11 END MX MY MZ
92 START MX MY MZ
92 END MX MY MZ
91 START MX MY MZ
91 END MX MY MZ
19 START MX MY MZ
19 END MX MY MZ
104 START MX MY MZ
104 END MX MY MZ
105 START MX MY MZ
105 END MX MY MZ
20 START MX MY MZ
20 END MX MY MZ
28 START MX MY MZ
28 END MX MY MZ
117 START MX MY MZ
117 END MX MY MZ
118 START MX MY MZ
118 END MX MY MZ
29 START MX MY MZ
29 END MX MY MZ
34 START MX MY MZ
34 END MX MY MZ
DEFINE REFERENCE LOADS
LOAD R1 LOADTYPE Mass TITLE REF MASS MODEL
SELFWEIGHT X 1
SELFWEIGHT Y 1
SELFWEIGHT Z 1
MEMBER LOAD
1 TO 11 71 TO 92 UNI GX 3
1 TO 11 71 TO 92 UNI GY 3
1 TO 11 71 TO 92 UNI GZ 3
MEMBER LOAD
1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GX 13
1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GY 13
1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GZ 13
MEMBER LOAD
5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GX 7.31
5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GY 7.31
5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GZ 7.31
MEMBER LOAD
71 UNI GX 7.25
71 UNI GY 7.25
71 UNI GZ 7.25
MEMBER LOAD
69 UNI GX 12.19
69 UNI GY 12.19
69 UNI GZ 12.19
MEMBER LOAD
21 24 106 107 109 TO 112 UNI GX 2.75
21 24 106 107 109 TO 112 UNI GY 2.75
21 24 106 107 109 TO 112 UNI GZ 2.75
MEMBER LOAD
30 TO 33 119 120 UNI GX 1.25
30 TO 33 119 120 UNI GY 1.25
30 TO 33 119 120 UNI GZ 1.25
MEMBER LOAD
22 23 27 108 115 116 UNI GX 10.75
22 23 27 108 115 116 UNI GY 10.75
22 23 27 108 115 116 UNI GZ 10.75
MEMBER LOAD
70 UNI GX 14.81
70 UNI GY 14.81
70 UNI GZ 14.81
MEMBER LOAD
8 19 28 UNI GX 12.76
8 19 28 UNI GY 12.76
8 19 28 UNI GZ 12.76
MEMBER LOAD
69 70 UNI GZ 17.25
69 70 UNI GY 17.25
69 70 UNI GY 17.25
JOINT LOAD
82 TO 85 FX 13.91
82 TO 85 FY 13.91
82 TO 85 FZ 13.91
FLOOR LOAD
YRANGE 4.2 4.2 FLOAD 4.94 GX
YRANGE 4.2 4.2 FLOAD 4.94 GY
YRANGE 4.2 4.2 FLOAD 4.94 GZ
FLOOR LOAD
YRANGE 7.8 10.9 FLOAD 6.28 GX
YRANGE 7.8 10.9 FLOAD 6.28 GY
YRANGE 7.8 10.9 FLOAD 6.28 GZ
MEMBER LOAD
8 19 28 UNI GX 1.62
8 19 28 UNI GY 1.62
8 19 28 UNI GZ 1.62
MEMBER LOAD
69 70 UNI GX 2.43
69 70 UNI GY 2.43
69 70 UNI GZ 2.43
FLOOR LOAD
YRANGE 4.2 4.2 FLOAD 1.2 GX
YRANGE 4.2 4.2 FLOAD 1.2 GY
YRANGE 4.2 4.2 FLOAD 1.2 GZ
FLOOR LOAD
YRANGE 7.8 7.8 FLOAD 0.5 GX
YRANGE 7.8 7.8 FLOAD 0.5 GY
YRANGE 7.8 7.8 FLOAD 0.5 GZ
FLOOR LOAD
YRANGE 10.3 10.9 FLOAD 0.2 GX
YRANGE 10.3 10.9 FLOAD 0.2 GY
YRANGE 10.3 10.9 FLOAD 0.2 GZ
END DEFINE REFERENCE LOADS
FLOOR DIAPHRAGM
DIA 1 TYPE RIG HEI 4.2
DIA 2 TYPE RIG HEI 7.8
DIA 3 TYPE RIG HEI 10.3
DIA 4 TYPE RIG HEI 10.9
CHECK SOFT STORY 1893 2016
CUT OFF MODE SHAPE 10
*-------------------------------------------------------------------SEISMIC LOAD
DEFINE IS1893 2016 LOAD
ZONE 0.16 RF 5 I 1.2 SS 2 ST 1 DM 0.05 PX 0.254 PZ 0.403 DT 1.5
LOAD 1 LOADTYPE None TITLE SL-X
1893 LOAD X
LOAD 2 LOADTYPE None TITLE SL-Y
1893 LOAD Y
LOAD 3 LOADTYPE None TITLE SL-Z
1893 LOAD Z
*DEAD LOAD CASE............................................................................................
LOAD 4 LOADTYPE None TITLE DL
SELFWEIGHT Y -1
MEMBER LOAD
1 TO 11 71 TO 92 UNI GY -3
1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GY -13
5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GY -7.31
71 UNI GY -7.25
69 UNI GY -12.19
21 24 106 107 109 TO 112 UNI GY -2.75
30 TO 33 119 120 UNI GY -1.25
22 23 27 108 115 116 UNI GY -10.75
70 UNI GY -14.81
8 19 28 UNI GY -12.76
69 70 UNI GY -17.25
JOINT LOAD
82 TO 85 FY -13.91
FLOOR LOAD
YRANGE 4.2 4.2 FLOAD -4.94 GY
YRANGE 7.8 10.9 FLOAD -6.28 GY
*LIVE LOAD CASE.....................................................................................
LOAD 5 LOADTYPE Live TITLE LL
MEMBER LOAD
8 19 28 UNI GY -6.48
69 70 UNI GY -9.72
FLOOR LOAD
YRANGE 4.2 4.2 FLOAD -5 GY
YRANGE 7.8 7.8 FLOAD -2 GY
YRANGE 10.3 10.9 FLOAD -0.75 GY
LOAD 6 LOADTYPE Wind TITLE WLX
FLOOR LOAD
XRANGE 13.05 13.05 FLOAD -1.73 YRANGE 0 10.3 ZRANGE 0 5.05 GX
LOAD 7 LOADTYPE Wind TITLE WLZ
FLOOR LOAD
ZRANGE 0 0 FLOAD 1.73 GZ
LOAD 8 LOADTYPE None TITLE RSX
SPECTRUM CQC IS1893 2016 TOR DEC 1 ECC 0.05 X 0.054 SCALE 1 DAMP 0.05
SOIL TYPE 2
LOAD 9 LOADTYPE None TITLE RSY
SPECTRUM CQC IS1893 2016 TOR DEC 1 ECC 0.05 Y 0.0828 SCALE 1 DAMP 0.05
SOIL TYPE 2
LOAD 10 LOADTYPE None TITLE RSZ
SPECTRUM CQC IS1893 2016 TOR DEC 1 ECC 0.05 Z 0.0864 SCALE 1 DAMP 0.05
SOIL TYPE 2
*----------------------------------------- LOAD COMBINATION
***********************************************
LOAD COMB 11 (DL + LL)
4 1.0 5 1.0
LOAD COMB 12 (DL + RSX)
4 1.0 8 1.0
LOAD COMB 13 (DL - RSX)
4 1.0 8 -1.0
LOAD COMB 14 (DL + RSY)
4 1.0 9 1.0
LOAD COMB 15 (DL - RSY)
4 1.0 9 -1.0
LOAD COMB 16 (DL + RSZ)
4 1.0 10 1.0
LOAD COMB 17 (DL - RSZ )
4 1.0 10 -1.0
LOAD COMB 18 (DL + WLX)
4 1.0 6 1.0
LOAD COMB 19 (DL - WLX)
4 1.0 6 -1.0
LOAD COMB 20 DL + WLZ)
4 1.0 7 1.0
LOAD COMB 21 (DL - WLZ)
4 1.0 7 -1.0
*--------------------------------- ( LIMIT STATE OF SERVICEABILITY )
LOAD COMB 22 (DL + 0.8LL + 0.8RSX)
4 1.0 5 0.8 8 0.8
LOAD COMB 23 (DL + 0.8LL - 0.8RSX)
4 1.0 5 0.8 8 -0.8
LOAD COMB 24 (DL + 0.8LL + 0.8RSY)
4 1.0 5 0.8 9 0.8
LOAD COMB 25 (DL + 0.8LL - 0.8RSY)
4 1.0 5 0.8 9 -0.8
LOAD COMB 26 (DL + 0.8LL + 0.8RSZ)
4 1.0 5 0.8 10 0.8
LOAD COMB 27 (DL + 0.8LL - 0.8RSZ)
4 1.0 5 0.8 10 -0.8
LOAD COMB 28 (DL + 0.8LL + 0.8WLX)
4 1.0 5 0.8 6 0.8
LOAD COMB 29 (DL + 0.8LL - 0.8WLX)
4 1.0 5 0.8 6 -0.8
LOAD COMB 30 (DL + 0.8LL + 0.8WLZ)
4 1.0 5 0.8 7 0.8
LOAD COMB 31 (DL + 0.8LL - 0.8WLZ)
4 1.0 5 0.8 7 -0.8
*--------------------------------- ( LIMIT STATE OF COLLAPSE )
LOAD COMB 32 (1.5DL+1.5LL)
4 1.5 5 1.5
LOAD COMB 33 (1.5DL + 1.5RSX)
4 1.5 8 1.5
LOAD COMB 34 (1.5DL - 1.5RSX)
4 1.5 8 -1.5
LOAD COMB 35 (1.5DL + 1.5RSY)
4 1.5 9 1.5
LOAD COMB 36 (1.5DL - 1.5RSY)
4 1.5 8 -1.5
LOAD COMB 37 (1.5DL + 1.5RSZ)
4 1.5 10 1.5
LOAD COMB 38 (1.5DL - 1.5RSZ)
4 1.5 10 -1.5
LOAD COMB 39 (1.5DL + 1.5WLX)
4 1.5 6 1.5
LOAD COMB 40 (1.5DL - 1.5WLX)
4 1.5 6 -1.5
LOAD COMB 41 (0.9DL + 1.5RSX)
4 0.9 8 1.5
LOAD COMB 42 (0.9DL - 1.5RSX)
4 0.9 8 -1.5
LOAD COMB 43 (0.9DL + 1.5RSY)
4 0.9 9 1.5
LOAD COMB 44 (0.9DL - 1.5RSY)
4 0.9 9 -1.5
LOAD COMB 45 (0.9DL + 1.5RSZ)
4 0.9 10 1.5
LOAD COMB 46 (0.9DL - 1.5RSZ)
4 0.9 10 -1.5
LOAD COMB 47 (0.9DL + 1.5WLX)
4 0.9 6 1.5
LOAD COMB 48 (0.9DL - 1.5WLX)
4 0.9 6 -1.5
LOAD COMB 49 (1.2DL + 1.2LL + 1.2RSX)
4 1.2 5 1.2 8 1.2
LOAD COMB 50 (1.2DL + 1.2LL - 1.2RSX)
4 1.2 5 1.2 8 -1.2
LOAD COMB 51 (1.2DL + 1.2LL + 1.2RSY)
4 1.2 5 1.2 9 1.2
LOAD COMB 52 (1.2DL + 1.2LL - 1.2RSY)
4 1.2 5 1.2 9 -1.2
LOAD COMB 53 (1.2DL + 1.2LL + 1.2RSZ)
4 1.2 5 1.2 10 1.2
LOAD COMB 54 (1.2DL + 1.2LL - 1.2RSZ)
4 1.2 5 1.2 10 -1.2
LOAD COMB 55 (1.2DL + 1.2LL + 1.2WLX)
4 1.2 5 1.2 6 1.2
LOAD COMB 56 (1.2DL + 1.2LL - 1.2WLX)
4 1.2 5 1.2 6 -1.2
LOAD COMB 57 (1.2DL + 1.2LL + 1.2WLZ)
4 1.2 5 1.2 7 1.2
LOAD COMB 58 (1.2DL + 1.2LL - 1.2WLZ)
4 1.2 5 1.2 7 -1.2
LOAD COMB 59 (DL+LL+RSX+0.3XRSY+RSZ)
4 1.0 5 1.0 8 1.0 9 0.3 10 1.0
PERFORM ANALYSIS
LOAD LIST 11 TO 59
FINISH
STAAD OUTPUT FILE
STRUCTURAL DESIGN DOCUMENTATION OF PROPOSED TWO STORIED INDUSTRIAL
BUILDING OF EI LOCATION HUT.

PAGE NO. 1

_
****************************************************
* *
* STAAD.Pro CONNECT Edition *
* Version 22.00.00.15 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= JAN 25, 2025 *
* Time= 13:22:46 *
* *
* Licensed to: only @ ::LAVTeam:: (R) *
****************************************************
_
1. STAAD SPACE DXF IMPORT OF EI LOCATION HUT.DXF
INPUT FILE: F:\OFFICE\2024\DECEMBER\EI LOCATION HUT\R1\STAAD R1\EI
LOCATION HUT.STD
2. START JOB INFORMATION
3. JOB NAME TWO STORIED INDUSTRIAL BUILDING
4. JOB CLIENT EI LOCATION HUT
5. JOB NO DGS_3402
6. JOB REV 1
7. ENGINEER NAME JM
8. ENGINEER DATE 1/25/2025
9. END JOB INFORMATION
10. INPUT WIDTH 79
11. UNIT METER KN
12. JOINT COORDINATES
13. 1 0 0 0; 2 13.05 0 0; 3 13.05 0 5.05; 4 0 0 5.05; 6 6.575 0 5.05; 7 3.775 0 0
14. 8 3.775 0 5.05; 9 9.275 0 0; 10 9.275 0 5.05; 11 9.275 0 4.05; 12 13.05 0 4.05
15. 13 3.775 0 1.475; 14 9.275 0 1.475; 15 3.775 0 3.575; 16 9.275 0 3.575
16. 17 8.025 0 0; 18 8.025 0 5.05; 20 9.275 4.2 0; 21 13.05 4.2 0
17. 22 13.05 4.2 5.05; 25 6.575 4.2 5.05; 26 3.775 4.2 0; 27 3.775 4.2 5.05
18. 28 9.275 4.2 5.05; 29 9.275 4.2 4.05; 30 13.05 4.2 4.05; 31 5.86E-14 4.2 3.8
19. 32 9.275 4.2 3.8; 34 9.275 7.8 0; 35 13.05 7.8 0; 36 13.05 7.8 5.05
20. 39 6.575 7.8 5.05; 40 3.775 7.8 0; 41 3.775 7.8 5.05; 42 9.275 7.8 5.05
21. 43 9.275 7.8 4.05; 44 13.05 7.8 4.05; 45 5.86E-14 7.8 3.8; 46 9.275 7.8 3.8
22. 47 9.275 10.3 0; 48 13.05 10.3 0; 49 13.05 10.3 5.05; 50 9.275 10.3 5.05
23. 51 9.275 10.3 2.525; 52 13.05 10.3 2.525; 53 0 -1.5 0; 54 3.775 -1.5 0
24. 55 6.575 -1.5 7.99E-14; 56 6.575 0 7.99E-14; 57 9.275 -1.5 0; 58 13.05 -1.5 0
25. 59 0 -1.5 5.05; 60 3.775 -1.5 5.05; 61 6.575 -1.5 5.05; 62 9.275 -1.5 5.05
26. 63 13.05 -1.5 5.05; 64 0 4.2 0; 65 6.575 4.2 7.99E-14; 66 0 4.2 5.05
27. 67 0 7.8 0; 68 6.575 7.8 7.99E-14; 69 0 7.8 5.05; 70 13.05 2.4 0
28. 71 9.275 2.4 0; 72 13.05 6 0; 73 9.275 6 0; 74 6.575 0 3.575; 75 6.575 0 1.475
29. 76 8.025 0 1.475; 77 8.025 0 3.575; 78 6.575 4.2 3.8; 79 3.775 4.2 3.8
 30. 80 6.575 7.8 3.8; 81 3.775 7.8 3.8; 82 9.275 10.9 0; 83 13.05 10.9 0
31. 84 9.275 10.9 2.525; 85 13.05 10.9 2.525
32. MEMBER INCIDENCES
33. 1 1 7; 2 2 12; 3 3 10; 4 4 1; 5 56 75; 6 7 13; 7 9 14; 8 11 12; 9 13 75
34. 10 15 74; 11 17 76; 12 64 26; 13 21 30; 14 22 28; 15 66 31; 16 65 78; 17 26 79
35. 18 20 32; 19 29 30; 20 31 79; 21 67 40; 22 35 44; 23 36 42; 24 69 45; 25 68 80
36. 26 40 81; 27 34 46; 28 43 44; 29 45 81; 30 47 48; 31 48 52; 32 49 50; 33 47 51
37. 34 51 52; 35 53 1; 36 54 7; 37 55 56; 38 57 9; 39 58 2; 40 59 4; 41 60 8
38. 42 61 6; 43 62 10; 44 63 3; 45 34 47; 46 35 48; 47 42 50; 48 36 49; 49 1 64
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 2

39. 50 7 26; 51 56 65; 52 9 71; 53 2 70; 54 4 66; 55 8 27; 56 6 25; 57 10 28

40. 58 3 22; 59 64 67; 60 26 40; 61 65 68; 62 20 73; 63 21 72; 64 66 69; 65 27 41
41. 66 25 39; 67 28 42; 68 22 36; 69 70 71; 70 72 73; 71 9 2; 72 17 9; 73 56 17
42. 74 7 56; 75 12 3; 76 8 4; 77 6 8; 78 18 6; 79 10 18; 80 74 6; 81 75 74
43. 82 15 8; 83 13 15; 84 11 10; 85 16 11; 86 14 16; 87 76 14; 88 75 76; 89 77 16
44. 90 74 77; 91 77 18; 92 76 77; 93 65 20; 94 26 65; 95 30 22; 96 27 66; 97 25 27
45. 98 28 25; 99 31 64; 100 78 25; 101 79 27; 102 29 28; 103 32 29; 104 78 32
46. 105 79 78; 106 68 34; 107 40 68; 108 44 36; 109 41 69; 110 39 41; 111 42 39
47. 112 45 67; 113 80 39; 114 81 41; 115 43 42; 116 46 43; 117 80 46; 118 81 80
48. 119 52 49; 120 51 50; 121 71 20; 122 70 21; 123 73 34; 124 72 35; 125 47 82
49. 126 48 83; 127 51 84; 128 52 85; 129 82 83; 130 83 85; 131 85 84; 132 84 82
50. DEFINE MATERIAL START
51. ISOTROPIC CONCRETE
52. E 2.17185E+07
53. POISSON 0.17
54. DENSITY 23.5616
55. ALPHA 1E-05
56. DAMP 0.05
57. TYPE CONCRETE
58. STRENGTH FCU 27579
59. END DEFINE MATERIAL
60. MEMBER PROPERTY AMERICAN
61. 12 TO 29 69 70 93 TO 118 129 TO 132 PRIS YD 0.35 ZD 0.25
62. 30 32 34 PRIS YD 0.3 ZD 0.25
63. MEMBER PROPERTY AMERICAN
64. 1 TO 11 71 TO 92 PRIS YD 0.35 ZD 0.25
65. 35 TO 37 40 TO 42 49 TO 51 54 TO 56 59 TO 61 64 TO 66 PRIS YD 0.35 ZD 0.4
66. 127 128 PRIS YD 0.3 ZD 0.3
67. MEMBER PROPERTY AMERICAN
68. 38 39 43 TO 48 52 53 57 58 62 63 67 68 121 TO 126 PRIS YD 0.35 ZD 0.5
69. MEMBER PROPERTY AMERICAN
70. 31 33 119 120 PRIS YD 0.35 ZD 0.35
71. CONSTANTS
72. MATERIAL CONCRETE ALL
73. SUPPORTS
74. 53 TO 55 57 TO 63 FIXED
75. MEMBER RELEASE
76. 8 START MX MY MZ
77. 8 END MX MY MZ
78. 90 START MX MY MZ
79. 89 END MX MY MZ
80. 88 START MX MY MZ
81. 87 END MX MY MZ
 82. 10 START MX MY MZ
83. 10 END MX MY MZ
84. 9 START MX MY MZ
85. 9 END MX MY MZ
86. 11 START MX MY MZ
87. 11 END MX MY MZ
88. 92 START MX MY MZ
89. 92 END MX MY MZ
90. 91 START MX MY MZ
91. 91 END MX MY MZ
92. 19 START MX MY MZ
93. 19 END MX MY MZ
94. 104 START MX MY MZ
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 3

95. 104 END MX MY MZ

96. 105 START MX MY MZ
97. 105 END MX MY MZ
98. 20 START MX MY MZ
99. 20 END MX MY MZ
100. 28 START MX MY MZ
101. 28 END MX MY MZ
102. 117 START MX MY MZ
103. 117 END MX MY MZ
104. 118 START MX MY MZ
105. 118 END MX MY MZ
106. 29 START MX MY MZ
107. 29 END MX MY MZ
108. 34 START MX MY MZ
109. 34 END MX MY MZ
110. DEFINE REFERENCE LOADS
111. LOAD R1 LOADTYPE MASS TITLE REF MASS MODEL
112. SELFWEIGHT X 1
113. SELFWEIGHT Y 1
114. SELFWEIGHT Z 1
115. MEMBER LOAD
116. 1 TO 11 71 TO 92 UNI GX 3
117. 1 TO 11 71 TO 92 UNI GY 3
118. 1 TO 11 71 TO 92 UNI GZ 3
119. MEMBER LOAD
120. 1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GX 13
121. 1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GY 13
122. 1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GZ 13
123. MEMBER LOAD
124. 5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GX 7.31
125. 5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GY 7.31
126. 5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GZ 7.31
127. MEMBER LOAD
128. 71 UNI GX 7.25
129. 71 UNI GY 7.25
130. 71 UNI GZ 7.25
131. MEMBER LOAD
132. 69 UNI GX 12.19
133. 69 UNI GY 12.19
 134. 69 UNI GZ 12.19
135. MEMBER LOAD
136. 21 24 106 107 109 TO 112 UNI GX 2.75
137. 21 24 106 107 109 TO 112 UNI GY 2.75
138. 21 24 106 107 109 TO 112 UNI GZ 2.75
139. MEMBER LOAD
140. 30 TO 33 119 120 UNI GX 1.25
141. 30 TO 33 119 120 UNI GY 1.25
142. 30 TO 33 119 120 UNI GZ 1.25
143. MEMBER LOAD
144. 22 23 27 108 115 116 UNI GX 10.75
145. 22 23 27 108 115 116 UNI GY 10.75
146. 22 23 27 108 115 116 UNI GZ 10.75
147. MEMBER LOAD
148. 70 UNI GX 14.81
149. 70 UNI GY 14.81
150. 70 UNI GZ 14.81
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 4

151. MEMBER LOAD

152. 8 19 28 UNI GX 12.76
153. 8 19 28 UNI GY 12.76
154. 8 19 28 UNI GZ 12.76
155. MEMBER LOAD
156. 69 70 UNI GZ 17.25
157. 69 70 UNI GY 17.25
158. 69 70 UNI GY 17.25
159. JOINT LOAD
160. 82 TO 85 FX 13.91
161. 82 TO 85 FY 13.91
162. 82 TO 85 FZ 13.91
163. FLOOR LOAD
164. YRANGE 4.2 4.2 FLOAD 4.94 GX
165. YRANGE 4.2 4.2 FLOAD 4.94 GY
166. YRANGE 4.2 4.2 FLOAD 4.94 GZ
167. FLOOR LOAD
168. YRANGE 7.8 10.9 FLOAD 6.28 GX
169. YRANGE 7.8 10.9 FLOAD 6.28 GY
170. YRANGE 7.8 10.9 FLOAD 6.28 GZ
171. MEMBER LOAD
172. 8 19 28 UNI GX 1.62
173. 8 19 28 UNI GY 1.62
174. 8 19 28 UNI GZ 1.62
175. MEMBER LOAD
176. 69 70 UNI GX 2.43
177. 69 70 UNI GY 2.43
178. 69 70 UNI GZ 2.43
179. FLOOR LOAD
180. YRANGE 4.2 4.2 FLOAD 1.2 GX
181. YRANGE 4.2 4.2 FLOAD 1.2 GY
182. YRANGE 4.2 4.2 FLOAD 1.2 GZ
183. FLOOR LOAD
184. YRANGE 7.8 7.8 FLOAD 0.5 GX
185. YRANGE 7.8 7.8 FLOAD 0.5 GY
 186. YRANGE 7.8 7.8 FLOAD 0.5 GZ
187. FLOOR LOAD
188. YRANGE 10.3 10.9 FLOAD 0.2 GX
189. YRANGE 10.3 10.9 FLOAD 0.2 GY
190. YRANGE 10.3 10.9 FLOAD 0.2 GZ
191. END DEFINE REFERENCE LOADS
_
*** NOTE: MASS MODEL FORMED WILL BE USED IN SEISMIC/RESPONSE/TIME
HISTORY LOADING, IF ANY.
IF MASS MODEL IS SEPARATELY PROVIDED IN INDIVIDUAL LOADING, THE
GENERATED MASS
WILL BE REPLACED BY THE MASS PROVIDED IN INDIVIDUAL LOADING.
_
192. FLOOR DIAPHRAGM
193. DIA 1 TYPE RIG HEI 4.2
194. DIA 2 TYPE RIG HEI 7.8
195. DIA 3 TYPE RIG HEI 10.3
196. DIA 4 TYPE RIG HEI 10.9
197. CHECK SOFT STORY 1893 2016
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 5

_FLOOR DIAPHRAGM_
_
***************************************************************************
*********

FLOOR DIAPHRAGM UNIT - KN METE

--------------- ----------------

NO. TYPE FL. LEVEL FL. WT

CENTRE OF MASS MASTER JOINT NO.
Z X
_
1 RIGID 4.200 1140.47 6.093 2.911 86
2 RIGID 7.800 815.00 6.929 2.907 87
3 RIGID 10.300 219.12 11.163 2.496 88
4 RIGID 10.900 147.13 11.163 1.252 89
_
***************************************************************************
*********

_
198. CUT OFF MODE SHAPE 10
199. *-------------------------------------------------------------------SEISMIC LOA
200. DEFINE IS1893 2016 LOAD
201. ZONE 0.16 RF 5 I 1.2 SS 2 ST 1 DM 0.05 PX 0.254 PZ 0.403 DT 1.5
202. LOAD 1 LOADTYPE NONE TITLE SL-X
203. 1893 LOAD X
204. LOAD 2 LOADTYPE NONE TITLE SL-Y
205. 1893 LOAD Y
206. LOAD 3 LOADTYPE NONE TITLE SL-Z
207. 1893 LOAD Z
208. *DEAD LOAD CASE................................................................
209. LOAD 4 LOADTYPE NONE TITLE DL
 210. SELFWEIGHT Y -1
211. MEMBER LOAD
212. 1 TO 11 71 TO 92 UNI GY -3
213. 1 TO 4 12 TO 15 72 TO 79 93 TO 99 UNI GY -13
214. 5 TO 7 9 TO 11 18 20 80 82 TO 91 102 TO 105 UNI GY -7.31
215. 71 UNI GY -7.25
216. 69 UNI GY -12.19
217. 21 24 106 107 109 TO 112 UNI GY -2.75
218. 30 TO 33 119 120 UNI GY -1.25
219. 22 23 27 108 115 116 UNI GY -10.75
220. 70 UNI GY -14.81
221. 8 19 28 UNI GY -12.76
222. 69 70 UNI GY -17.25
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 6

223. JOINT LOAD

224. 82 TO 85 FY -13.91
225. FLOOR LOAD
226. YRANGE 4.2 4.2 FLOAD -4.94 GY
**NOTE** about Floor/OneWay Loads/Weights.
Please note that depending on the shape of the floor you may
have to break up the FLOOR/ONEWAY LOAD into multiple commands.
For details please refer to Technical Reference Manual
Section 5.32.4.2 Note d and/or "5.32.4.3 Note f.

227. YRANGE 7.8 10.9 FLOAD -6.28 GY

228. *LIVE LOAD CASE................................................................
229. LOAD 5 LOADTYPE LIVE TITLE LL
230. MEMBER LOAD
231. 8 19 28 UNI GY -6.48
232. 69 70 UNI GY -9.72
233. FLOOR LOAD
234. YRANGE 4.2 4.2 FLOAD -5 GY
235. YRANGE 7.8 7.8 FLOAD -2 GY
236. YRANGE 10.3 10.9 FLOAD -0.75 GY
237. LOAD 6 LOADTYPE WIND TITLE WLX
238. FLOOR LOAD
239. XRANGE 13.05 13.05 FLOAD -1.73 YRANGE 0 10.3 ZRANGE 0 5.05 GX
240. LOAD 7 LOADTYPE WIND TITLE WLZ
241. FLOOR LOAD
242. ZRANGE 0 0 FLOAD 1.73 GZ
243. LOAD 8 LOADTYPE NONE TITLE RSX
244. SPECTRUM CQC IS1893 2016 TOR DEC 1 ECC 0.05 X 0.054 SCALE 1 DAMP 0.05
245. SOIL TYPE 2
246. LOAD 9 LOADTYPE NONE TITLE RSY
247. SPECTRUM CQC IS1893 2016 TOR DEC 1 ECC 0.05 Y 0.0828 SCALE 1 DAMP
0.05
248. SOIL TYPE 2
249. LOAD 10 LOADTYPE NONE TITLE RSZ
250. SPECTRUM CQC IS1893 2016 TOR DEC 1 ECC 0.05 Z 0.0864 SCALE 1 DAMP 0.05
251. SOIL TYPE 2
252. *----------------------------------------- LOAD COMBINATION
253. ***********************************************
254. LOAD COMB 11 (DL + LL)
 255. 4 1.0 5 1.0
256. LOAD COMB 12 (DL + RSX)
257. 4 1.0 8 1.0
258. LOAD COMB 13 (DL - RSX)
259. 4 1.0 8 -1.0
260. LOAD COMB 14 (DL + RSY)
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 7

261. 4 1.0 9 1.0

262. LOAD COMB 15 (DL - RSY)
263. 4 1.0 9 -1.0
264. LOAD COMB 16 (DL + RSZ)
265. 4 1.0 10 1.0
266. LOAD COMB 17 (DL - RSZ )
267. 4 1.0 10 -1.0
268. LOAD COMB 18 (DL + WLX)
269. 4 1.0 6 1.0
270. LOAD COMB 19 (DL - WLX)
271. 4 1.0 6 -1.0
272. LOAD COMB 20 DL + WLZ)
273. 4 1.0 7 1.0
274. LOAD COMB 21 (DL - WLZ)
275. 4 1.0 7 -1.0
276. *--------------------------------- ( LIMIT STATE OF SERVICEABILITY )
277. LOAD COMB 22 (DL + 0.8LL + 0.8RSX)
278. 4 1.0 5 0.8 8 0.8
279. LOAD COMB 23 (DL + 0.8LL - 0.8RSX)
280. 4 1.0 5 0.8 8 -0.8
281. LOAD COMB 24 (DL + 0.8LL + 0.8RSY)
282. 4 1.0 5 0.8 9 0.8
283. LOAD COMB 25 (DL + 0.8LL - 0.8RSY)
284. 4 1.0 5 0.8 9 -0.8
285. LOAD COMB 26 (DL + 0.8LL + 0.8RSZ)
286. 4 1.0 5 0.8 10 0.8
287. LOAD COMB 27 (DL + 0.8LL - 0.8RSZ)
288. 4 1.0 5 0.8 10 -0.8
289. LOAD COMB 28 (DL + 0.8LL + 0.8WLX)
290. 4 1.0 5 0.8 6 0.8
291. LOAD COMB 29 (DL + 0.8LL - 0.8WLX)
292. 4 1.0 5 0.8 6 -0.8
293. LOAD COMB 30 (DL + 0.8LL + 0.8WLZ)
294. 4 1.0 5 0.8 7 0.8
295. LOAD COMB 31 (DL + 0.8LL - 0.8WLZ)
296. 4 1.0 5 0.8 7 -0.8
297. *--------------------------------- ( LIMIT STATE OF COLLAPSE )
298. LOAD COMB 32 (1.5DL+1.5LL)
299. 4 1.5 5 1.5
300. LOAD COMB 33 (1.5DL + 1.5RSX)
301. 4 1.5 8 1.5
302. LOAD COMB 34 (1.5DL - 1.5RSX)
303. 4 1.5 8 -1.5
304. LOAD COMB 35 (1.5DL + 1.5RSY)
305. 4 1.5 9 1.5
306. LOAD COMB 36 (1.5DL - 1.5RSY)
 307. 4 1.5 8 -1.5
308. LOAD COMB 37 (1.5DL + 1.5RSZ)
309. 4 1.5 10 1.5
310. LOAD COMB 38 (1.5DL - 1.5RSZ)
311. 4 1.5 10 -1.5
312. LOAD COMB 39 (1.5DL + 1.5WLX)
313. 4 1.5 6 1.5
314. LOAD COMB 40 (1.5DL - 1.5WLX)
315. 4 1.5 6 -1.5
316. LOAD COMB 41 (0.9DL + 1.5RSX)
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 8

317. 4 0.9 8 1.5

318. LOAD COMB 42 (0.9DL - 1.5RSX)
319. 4 0.9 8 -1.5
320. LOAD COMB 43 (0.9DL + 1.5RSY)
321. 4 0.9 9 1.5
322. LOAD COMB 44 (0.9DL - 1.5RSY)
323. 4 0.9 9 -1.5
324. LOAD COMB 45 (0.9DL + 1.5RSZ)
325. 4 0.9 10 1.5
326. LOAD COMB 46 (0.9DL - 1.5RSZ)
327. 4 0.9 10 -1.5
328. LOAD COMB 47 (0.9DL + 1.5WLX)
329. 4 0.9 6 1.5
330. LOAD COMB 48 (0.9DL - 1.5WLX)
331. 4 0.9 6 -1.5
332. LOAD COMB 49 (1.2DL + 1.2LL + 1.2RSX)
333. 4 1.2 5 1.2 8 1.2
334. LOAD COMB 50 (1.2DL + 1.2LL - 1.2RSX)
335. 4 1.2 5 1.2 8 -1.2
336. LOAD COMB 51 (1.2DL + 1.2LL + 1.2RSY)
337. 4 1.2 5 1.2 9 1.2
338. LOAD COMB 52 (1.2DL + 1.2LL - 1.2RSY)
339. 4 1.2 5 1.2 9 -1.2
340. LOAD COMB 53 (1.2DL + 1.2LL + 1.2RSZ)
341. 4 1.2 5 1.2 10 1.2
342. LOAD COMB 54 (1.2DL + 1.2LL - 1.2RSZ)
343. 4 1.2 5 1.2 10 -1.2
344. LOAD COMB 55 (1.2DL + 1.2LL + 1.2WLX)
345. 4 1.2 5 1.2 6 1.2
346. LOAD COMB 56 (1.2DL + 1.2LL - 1.2WLX)
347. 4 1.2 5 1.2 6 -1.2
348. LOAD COMB 57 (1.2DL + 1.2LL + 1.2WLZ)
349. 4 1.2 5 1.2 7 1.2
350. LOAD COMB 58 (1.2DL + 1.2LL - 1.2WLZ)
351. 4 1.2 5 1.2 7 -1.2
352. LOAD COMB 59 (DL+LL+RSX+0.3XRSY+RSZ)
353. 4 1.0 5 1.0 8 1.0 9 0.3 10 1.0
354. PERFORM ANALYSIS
_

PROBLEM STATISTICS
 -----------------------------------

NUMBER OF JOINTS 82 NUMBER OF MEMBERS 132

NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 10

Using 64-bit analysis engine.

SOLVER USED IS THE OUT-OF-CORE BASIC SOLVER

ORIGINAL/FINAL BAND-WIDTH= 62/ 15/ 292 DOF

_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 9

TOTAL PRIMARY LOAD CASES = 10, TOTAL DEGREES OF FREEDOM = 306

TOTAL LOAD COMBINATION CASES = 49 SO FAR.
SIZE OF STIFFNESS MATRIX = 90 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 13.7/ 442.1 MB

_
_
***NOTE: MASSES DEFINED UNDER LOAD# 8 WILL FORM
THE FINAL MASS MATRIX FOR DYNAMIC ANALYSIS.
_

**WARNING: IF THIS UBC/IBC ANALYSIS HAS TENSION/COMPRESSION

OR REPEAT LOAD OR RE-ANALYSIS OR SELECT OPTIMIZE, THEN EACH
UBC/IBC CASE SHOULD BE FOLLOWED BY PERFORM ANALYSIS & CHANGE.

*WARNING- ZERO STIFFNESS IN DIRECTION 4 AT JOINT 76 EQN.NO. 103

LOADS APPLIED OR DISTRIBUTED HERE FROM ELEMENTS WILL BE IGNORED.
THIS MAY BE DUE TO ALL MEMBERS AT THIS JOINT BEING RELEASED OR
EFFECTIVELY RELEASED IN THIS DIRECTION.
*WARNING- ZERO STIFFNESS IN DIRECTION 4 AT JOINT 77 EQN.NO. 139
WARNING : SOFT STOREY DETECTED.
STOREY 1 AT 4.200 METE IS SOFT ALONG GLOBAL X DIRECTION.
WARNING : SOFT STOREY DETECTED.
STOREY 3 AT 10.300 METE IS SOFT ALONG GLOBAL X DIRECTION.
WARNING : SOFT STOREY DETECTED.
STOREY 3 AT 10.300 METE IS SOFT ALONG GLOBAL Z DIRECTION.

_SOFT STORY CHECK_

_
VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK -
_______________
-------- ---------- --------------

STORY FL. LEVEL IN METE S T A T U S

----- ----------------- --------------------
X Z
_
1 4.20 SOFT OK
2 7.80 OK OK
3 10.30 SOFT SOFT
4 10.90 OK OK
***NOTE: Equivalent Static Analysis should preferably be performed for regular
structures with approximate natural time period less than 0.4s and regular
structures with height less than 15m in Seismic Zone II. Ref Cl.6.4.3 and 7.6
_BASE SHEAR AND TIME PERIOD IN X _
_--ABOVE GROUND LEVEL_

*********************************************************
* UNITS - KN METE *
* TIME PERIOD FOR X 1893 LOADING = 0.25400 SEC *
* SA/G PER 1893= 2.500, LOAD FACTOR= 1.000 *
* VB PER 1893= 0.0480 X 3934.21= 188.84 KN *
* VB Act Based on Clause 7.2.1 = 188.84 KN *
* VB Min based on Clause 7.2.2 = 43.28 KN *
* *
*********************************************************

_--MASS AND BASE SHEAR SUMMERY_

Units:KN METE
|------------------------------------------------------------------------------|
| Category | Mass | Ah | VB Calculated | VB Minimum | VB Final |
|------------------------------------------------------------------------------|
| Above GL | 3934.20947| 0.0480000| 188.84204 | 43.27630| 188.84204|
|------------------------------------------------------------------------------|
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 10

***NOTE: Equivalent Static Analysis should preferably be performed for regular

structures with approximate natural time period less than 0.4s and regular
structures with height less than 15m in Seismic Zone II. Ref Cl.6.4.3 and 7.6
_BASE SHEAR AND TIME PERIOD IN Y _
_--ABOVE GROUND LEVEL_

*********************************************************
* UNITS - KN METE *
* Calculation of SA/G for Y based on Clause 6.4.6 *
* SA/G PER 1893= 2.500, LOAD FACTOR= 1.000 *
* VB PER 1893= 0.0320 X 3934.21= 125.89 KN *
* *
*********************************************************

_--MASS AND BASE SHEAR SUMMERY_

Units:KN METE
|------------------------------------------------------------------------------|
| Category | Mass | Ah | VB Calculated | VB Minimum | VB Final |
|------------------------------------------------------------------------------|
| Above GL | 3934.20947| 0.0320000| 125.89471 | 0.00000| 125.89471|
|------------------------------------------------------------------------------|

***NOTE: Equivalent Static Analysis should preferably be performed for regular

 structures with approximate natural time period less than 0.4s and regular
structures with height less than 15m in Seismic Zone II. Ref Cl.6.4.3 and 7.6
_BASE SHEAR AND TIME PERIOD IN Z _
_--ABOVE GROUND LEVEL_

*********************************************************
* UNITS - KN METE *
* TIME PERIOD FOR Z 1893 LOADING = 0.40300 SEC *
* SA/G PER 1893= 2.500, LOAD FACTOR= 1.000 *
* VB PER 1893= 0.0480 X 3934.21= 188.84 KN *
* VB Act Based on Clause 7.2.1 = 188.84 KN *
* VB Min based on Clause 7.2.2 = 43.28 KN *
* *
*********************************************************

_--MASS AND BASE SHEAR SUMMERY_

Units:KN METE
|------------------------------------------------------------------------------|
| Category | Mass | Ah | VB Calculated | VB Minimum | VB Final |
|------------------------------------------------------------------------------|
| Above GL | 3934.20947| 0.0480000| 188.84204 | 43.27630| 188.84204|
|------------------------------------------------------------------------------|
EIGEN METHOD : SUBSPACE
-------------------------
NUMBER OF MODES REQUESTED = 10
NUMBER OF EXISTING MASSES IN THE MODEL = 132
NUMBER OF MODES THAT WILL BE USED = 10

*** _EIGENSOLUTION_: SUBSPACE METHOD ***

_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 11

CALCULATED FREQUENCIES FOR LOAD CASE 8

MODE FREQUENCY(CYCLES/SEC) PERIOD(SEC) ACCURACY

1 1.171 0.85369 3.935E-16

2 1.392 0.71817 0.000E+00
3 1.511 0.66175 7.882E-16
4 4.088 0.24464 5.170E-16
5 4.660 0.21457 1.193E-15
6 5.172 0.19334 1.722E-15
7 7.229 0.13834 2.648E-13
8 7.790 0.12836 6.106E-13
9 8.052 0.12419 3.356E-13
10 9.759 0.10247 2.411E-07

The following Frequencies are estimates that were calculated. These are for
information only and will not be used. Remaining values are either above
the cut off mode/freq values or are of low accuracy. To use these
frequencies, rerun with a higher cutoff mode (or mode + freq) value.
CALCULATED FREQUENCIES FOR LOAD CASE 8
MODE FREQUENCY(CYCLES/SEC) PERIOD(SEC) ACCURACY

11 9.972 0.10028 8.602E-10

12 10.738 0.09313 1.338E-06
13 10.846 0.09220 3.079E-10
14 11.068 0.09035 1.730E-07
15 11.139 0.08978 1.075E-05
16 11.455 0.08730 1.776E-07
17 11.880 0.08418 3.390E-06
18 11.951 0.08367 1.333E-05
19 12.318 0.08118 1.753E-05

_1893 RESPONSE SPECTRUM LOAD 8_

RESPONSE LOAD CASE 8

_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 12

MODAL WEIGHT (MODAL MASS TIMES g) IN KN GENERALIZED

MODE X Y Z WEIGHT

1 3.584417E+00 7.043715E-01 2.236643E+03 8.576700E+02

2 2.361259E+03 5.348528E-03 3.107800E+01 1.192269E+03
3 1.084108E+02 1.205076E-01 2.972153E+02 5.362190E+02
4 2.370748E+02 3.433623E-02 2.319751E+00 5.827362E+02
5 1.465635E+00 1.866503E+00 3.116733E+02 1.000414E+03
6 3.491478E+00 1.924120E+00 1.819206E+01 9.028528E+02
7 2.873153E+02 1.066293E+00 3.469734E+00 1.104499E+03
8 2.065990E+02 1.300748E+00 5.953715E+00 5.351626E+02
9 1.677506E+01 1.163390E+00 1.007322E+01 3.308513E+02
10 1.284884E-02 3.373140E+02 2.471541E+00 1.720115E+02

CQC MODAL COMBINATION METHOD USED.

DYNAMIC WEIGHT X Y Z 3.646521E+03 3.906996E+03 3.776758E+03 KN
MISSING WEIGHT X Y Z -4.205329E+02 -3.561496E+03 -8.576685E+02 KN
MODAL WEIGHT X Y Z 3.225988E+03 3.454996E+02 2.919090E+03 KN

RESPONSE LOAD CASE 8

MODE SPECTRAL ACCELERATION DESIGN SEISMIC COEFFICIENT
---- --------------------- ------------------------------
X Y Z

1 1.59309 0.0860 0.0000 0.0000

2 1.89371 0.1023 0.0000 0.0000
3 2.05517 0.1110 0.0000 0.0000
4 2.50000 0.1350 0.0000 0.0000
5 2.50000 0.1350 0.0000 0.0000
6 2.50000 0.1350 0.0000 0.0000
7 2.50000 0.1350 0.0000 0.0000
8 2.50000 0.1350 0.0000 0.0000
9 2.50000 0.1350 0.0000 0.0000
10 2.50000 0.1350 0.0000 0.0000

_PEAK STORY SHEAR_

_

STORY LEVEL IN METE PEAK STORY SHEAR IN KN

----- ------------- --------------------------------------------------
X Y Z

_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 13

_
4 10.90 24.48 0.00 0.00
3 10.30 58.55 0.00 0.00
2 7.80 148.26 0.00 0.00
1 4.20 238.30 0.00 0.00
BASE -1.50 258.81 0.00 0.00

MODE ACCELERATION-G DAMPING

---- -------------- -------

1 1.59309 0.05000
2 1.89371 0.05000
3 2.05517 0.05000
4 2.50000 0.05000
5 2.50000 0.05000
6 2.50000 0.05000
7 2.50000 0.05000
8 2.50000 0.05000
9 2.50000 0.05000
10 2.50000 0.05000
_
UNIT - METE
_
_

***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID

DIAPHRAGM.
 TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
_
_

STORY LEVEL FLOOR PLAN DIMENSION (bi)

----- ----- -------------------------------
X Z
_
4 10.90 3.77500 2.52500
3 10.30 3.77500 5.05000
2 7.80 13.05000 5.05000
1 4.20 13.05000 5.05000
_

ACCIDENTAL ECCENTRICITY (ecc) = 0.05bi

STORY LEVEL DESIGN ECCENTRICITY

----- ----- ----------------------------
X Z
esi + ecc esi + ecc
_
4 10.90 0.00000 0.12625
3 10.30 0.00000 0.25250
2 7.80 0.00000 0.25250
1 4.20 0.00000 0.25250
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 14

_PEAK ADDITIONAL TOR_

_

STORY LEVEL IN METE PEAK ADDITIONAL TORSION IN KN -METE

----- ------------- ------------------------------------
X Z

_
4 10.90 3.09 0.00
3 10.30 8.63 0.00
2 7.80 24.97 0.00
1 4.20 27.03 0.00
_
*** NOTE ***
A) STOREY SHEAR DEVELOPED DUE TO EACH MODE SHAPE AT EACH FLOOR
LEVEL ARE WRITTEN IN _RESP1893.TXT FILE.
B) STATIC AND DESIGN ECCENTRICITY OF EACH FLOOR ARE WRITTEN IN
_DIATOR.TXT FILE.
C) ADDITIONAL TORSIONAL MOMENT FOR EACH MODE SHAPE AT EACH
FLOOR LEVEL ARE WRITTEN IN _DIATOR.TXT FILE.
_

_MODAL BASE ACTIONS_

 MODAL BASE ACTIONS FORCES IN KN LENGTH IN METE
-----------------------------------------------------------
MOMENTS ARE ABOUT THE ORIGIN
MODE PERIOD FX FY FZ MX MY MZ

1 0.854 0.31 -0.14 -7.70 -53.08 64.09 -3.04

2 0.718 241.46 0.36 27.70 147.44 469.24 -1629.03
3 0.662 12.03 -0.40 -19.92 -91.15 116.74 -86.82
4 0.245 32.01 0.39 -3.17 4.81 107.79 86.28
5 0.215 0.20 -0.22 2.89 -4.29 -15.38 -1.09
6 0.193 0.47 -0.35 1.08 0.21 1.62 0.50
7 0.138 38.79 2.36 -4.26 -11.22 120.42 21.80
8 0.128 27.89 -2.21 4.73 12.11 46.45 -0.58
9 0.124 2.26 0.60 -1.75 -3.90 27.46 5.76
10 0.102 0.00 -0.28 0.02 0.73 -0.35 -3.07
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 15

_PARTICIPATION FACTORS_

MASS PARTICIPATION FACTORS IN PERCENT BASE SHEAR IN KN

-------------------------------------- ------------------

MODE X Y Z SUMM-X SUMM-Y SUMM-Z X Y Z

1 0.10 0.02 59.22 0.098 0.018 59.221 0.31 0.00 0.00

2 64.75 0.00 0.82 64.852 0.018 60.044 241.46 0.00 0.00
3 2.97 0.00 7.87 67.825 0.021 67.914 12.03 0.00 0.00
4 6.50 0.00 0.06 74.326 0.022 67.975 32.01 0.00 0.00
5 0.04 0.05 8.25 74.367 0.070 76.227 0.20 0.00 0.00
6 0.10 0.05 0.48 74.462 0.119 76.709 0.47 0.00 0.00
7 7.88 0.03 0.09 82.341 0.146 76.801 38.79 0.00 0.00
8 5.67 0.03 0.16 88.007 0.180 76.959 27.89 0.00 0.00
9 0.46 0.03 0.27 88.467 0.210 77.225 2.26 0.00 0.00
10 0.00 8.63 0.07 88.468 8.843 77.291 0.00 0.00 0.00
---------------------------
TOTAL SRSS SHEAR 248.52 0.00 0.00
TOTAL 10PCT SHEAR 264.31 0.00 0.00
TOTAL ABS SHEAR 355.42 0.00 0.00
TOTAL CSM SHEAR 324.02 0.00 0.00
TOTAL CQC SHEAR 258.81 0.00 0.00

*********************************************************
* UNITS - KN METE *
* TIME PERIOD FOR X 1893 LOADING = 0.25400 SEC *
* SA/G PER 1893= 2.500, LOAD FACTOR= 1.000 *
* FACTOR V PER 1893= 0.0468 X 3934.21 *
* VB Min based on Clause 7.2.2 = 43.28 *
*********************************************************
 _1893 RESPONSE SPECTRUM LOAD 9_

RESPONSE LOAD CASE 9

MODAL WEIGHT (MODAL MASS TIMES g) IN KN GENERALIZED

MODE X Y Z WEIGHT

1 3.584417E+00 7.043715E-01 2.236643E+03 8.576700E+02

2 2.361259E+03 5.348528E-03 3.107800E+01 1.192269E+03
3 1.084108E+02 1.205076E-01 2.972153E+02 5.362190E+02
4 2.370748E+02 3.433623E-02 2.319751E+00 5.827362E+02
5 1.465635E+00 1.866503E+00 3.116733E+02 1.000414E+03
6 3.491478E+00 1.924120E+00 1.819206E+01 9.028528E+02
7 2.873153E+02 1.066293E+00 3.469734E+00 1.104499E+03
8 2.065990E+02 1.300748E+00 5.953715E+00 5.351626E+02
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 16

9 1.677506E+01 1.163390E+00 1.007322E+01 3.308513E+02

10 1.284884E-02 3.373140E+02 2.471541E+00 1.720115E+02

CQC MODAL COMBINATION METHOD USED.

DYNAMIC WEIGHT X Y Z 3.646521E+03 3.906996E+03 3.776758E+03 KN
MISSING WEIGHT X Y Z -4.205329E+02 -3.561496E+03 -8.576685E+02 KN
MODAL WEIGHT X Y Z 3.225988E+03 3.454996E+02 2.919090E+03 KN

RESPONSE LOAD CASE 9

MODE SPECTRAL ACCELERATION DESIGN SEISMIC COEFFICIENT

---- --------------------- ------------------------------
X Y Z

1 2.50000 0.0000 0.1380 0.0000

2 2.50000 0.0000 0.1380 0.0000
3 2.50000 0.0000 0.1380 0.0000
4 2.50000 0.0000 0.1380 0.0000
5 2.50000 0.0000 0.1380 0.0000
6 2.50000 0.0000 0.1380 0.0000
7 2.50000 0.0000 0.1380 0.0000
8 2.50000 0.0000 0.1380 0.0000
9 2.50000 0.0000 0.1380 0.0000
10 2.50000 0.0000 0.1380 0.0000
 _PEAK STORY SHEAR_
_

STORY LEVEL IN METE PEAK STORY SHEAR IN KN

----- ------------- --------------------------------------------------
X Y Z

_
4 10.90 0.00 14.81 0.00
3 10.30 0.00 33.60 0.00
2 7.80 0.00 36.35 0.00
1 4.20 0.00 43.02 0.00
BASE -1.50 0.00 46.64 0.00

MODE ACCELERATION-G DAMPING

---- -------------- -------

1 2.50000 0.05000
2 2.50000 0.05000
3 2.50000 0.05000
4 2.50000 0.05000
5 2.50000 0.05000
6 2.50000 0.05000
7 2.50000 0.05000
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 17

MODE ACCELERATION-G DAMPING

---- -------------- -------

8 2.50000 0.05000
9 2.50000 0.05000
10 2.50000 0.05000

WARNING: ONLY X AND Z DIRECTIONS CAN BE CONSIDERED FOR IS-1893:2016

TORSION.
TORSION EFFECT IS EXCLUDED FOR LOADCASE NO. 9

_MODAL BASE ACTIONS_

MODAL BASE ACTIONS FORCES IN KN LENGTH IN METE

-----------------------------------------------------------
MOMENTS ARE ABOUT THE ORIGIN
MODE PERIOD FX FY FZ MX MY MZ

1 0.854 -0.22 0.10 5.48 37.75 -45.58 2.16

2 0.718 0.49 0.00 0.06 0.30 0.95 -3.31
3 0.662 -0.50 0.02 0.83 3.78 -4.84 3.60
 4 0.245 0.39 0.00 -0.04 0.06 1.33 1.06
5 0.215 -0.23 0.26 -3.33 4.94 17.74 1.26
6 0.193 -0.36 0.27 -0.82 -0.16 -1.23 -0.38
7 0.138 2.42 0.15 -0.27 -0.70 7.50 1.36
8 0.128 -2.26 0.18 -0.38 -0.98 -3.77 0.05
9 0.124 0.61 0.16 -0.47 -1.05 7.39 1.55
10 0.102 -0.29 46.55 -3.98 -121.47 57.18 508.04
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 18

_PARTICIPATION FACTORS_

MASS PARTICIPATION FACTORS IN PERCENT BASE SHEAR IN KN

-------------------------------------- ------------------

MODE X Y Z SUMM-X SUMM-Y SUMM-Z X Y Z

1 0.10 0.02 59.22

0.098 0.018 59.221 0.00 0.10 0.00
2 64.75 0.00 0.82
64.852 0.018 60.044 0.00 0.00 0.00
3 2.97 0.00 7.87
67.825 0.021 67.914 0.00 0.02 0.00
4 6.50 0.00 0.06
74.326 0.022 67.975 0.00 0.00 0.00
5 0.04 0.05 8.25
74.367 0.070 76.227 0.00 0.26 0.00
6 0.10 0.05 0.48
74.462 0.119 76.709 0.00 0.27 0.00
7 7.88 0.03 0.09
82.341 0.146 76.801 0.00 0.15 0.00
8 5.67 0.03 0.16
88.007 0.180 76.959 0.00 0.18 0.00
9 0.46 0.03 0.27
88.467 0.210 77.225 0.00 0.16 0.00
10 0.00 8.63 0.07
88.468 8.843 77.291 0.00 46.55 0.00
---------------------------
TOTAL SRSS SHEAR 0.00 46.55 0.00
TOTAL 10PCT SHEAR 0.00 46.55 0.00
TOTAL ABS SHEAR 0.00 47.68 0.00
TOTAL CSM SHEAR 0.00 46.55 0.00
TOTAL CQC SHEAR 0.00 46.64 0.00

_1893 RESPONSE SPECTRUM LOAD 10_

RESPONSE LOAD CASE 10

MODAL WEIGHT (MODAL MASS TIMES g) IN KN GENERALIZED

MODE X Y Z WEIGHT

1 3.584417E+00 7.043715E-01 2.236643E+03 8.576700E+02

2 2.361259E+03 5.348528E-03 3.107800E+01 1.192269E+03
3 1.084108E+02 1.205076E-01 2.972153E+02 5.362190E+02
4 2.370748E+02 3.433623E-02 2.319751E+00 5.827362E+02
5 1.465635E+00 1.866503E+00 3.116733E+02 1.000414E+03
 6 3.491478E+00 1.924120E+00 1.819206E+01 9.028528E+02
7 2.873153E+02 1.066293E+00 3.469734E+00 1.104499E+03
8 2.065990E+02 1.300748E+00 5.953715E+00 5.351626E+02
9 1.677506E+01 1.163390E+00 1.007322E+01 3.308513E+02
10 1.284884E-02 3.373140E+02 2.471541E+00 1.720115E+02
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 19

CQC MODAL COMBINATION METHOD USED.

DYNAMIC WEIGHT X Y Z 3.646521E+03 3.906996E+03 3.776758E+03 KN
MISSING WEIGHT X Y Z -4.205329E+02 -3.561496E+03 -8.576685E+02 KN
MODAL WEIGHT X Y Z 3.225988E+03 3.454996E+02 2.919090E+03 KN

RESPONSE LOAD CASE 10

MODE SPECTRAL ACCELERATION DESIGN SEISMIC COEFFICIENT

---- --------------------- ------------------------------
X Y Z

1 1.59309 0.0000 0.0000 0.1376

2 1.89371 0.0000 0.0000 0.1636
3 2.05517 0.0000 0.0000 0.1776
4 2.50000 0.0000 0.0000 0.2160
5 2.50000 0.0000 0.0000 0.2160
6 2.50000 0.0000 0.0000 0.2160
7 2.50000 0.0000 0.0000 0.2160
8 2.50000 0.0000 0.0000 0.2160
9 2.50000 0.0000 0.0000 0.2160
10 2.50000 0.0000 0.0000 0.2160

_PEAK STORY SHEAR_

_

STORY LEVEL IN METE PEAK STORY SHEAR IN KN

----- ------------- --------------------------------------------------
X Y Z

_
4 10.90 0.00 0.00 33.61
3 10.30 0.00 0.00 82.39
2 7.80 0.00 0.00 196.91
1 4.20 0.00 0.00 305.27
BASE -1.50 0.00 0.00 328.39

MODE ACCELERATION-G DAMPING

---- -------------- -------
 1 1.59309 0.05000
2 1.89371 0.05000
3 2.05517 0.05000
4 2.50000 0.05000
5 2.50000 0.05000
6 2.50000 0.05000
7 2.50000 0.05000
8 2.50000 0.05000
9 2.50000 0.05000
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 20

MODE ACCELERATION-G DAMPING

---- -------------- -------

10 2.50000 0.05000
_
UNIT - METE
_
_

***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID

DIAPHRAGM.
TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
_
_

STORY LEVEL FLOOR PLAN DIMENSION (bi)

----- ----- -------------------------------
X Z
_
4 10.90 3.77500 2.52500
3 10.30 3.77500 5.05000
2 7.80 13.05000 5.05000
1 4.20 13.05000 5.05000
_

ACCIDENTAL ECCENTRICITY (ecc) = 0.05bi

STORY LEVEL DESIGN ECCENTRICITY

----- ----- ----------------------------
X Z
esi + ecc esi + ecc
_
4 10.90 0.18875 0.00000
3 10.30 0.18875 0.00000
2 7.80 0.65250 0.00000
1 4.20 0.65250 0.00000

_PEAK ADDITIONAL TOR_

_
 STORY LEVEL IN METE PEAK ADDITIONAL TORSION IN KN -METE
----- ------------- ------------------------------------
X Z

_
4 10.90 0.00 6.34
3 10.30 0.00 9.21
2 7.80 0.00 78.71
1 4.20 0.00 99.55
_
_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 21

*** NOTE ***

A) STOREY SHEAR DEVELOPED DUE TO EACH MODE SHAPE AT EACH FLOOR
LEVEL ARE WRITTEN IN _RESP1893.TXT FILE.
B) STATIC AND DESIGN ECCENTRICITY OF EACH FLOOR ARE WRITTEN IN
_DIATOR.TXT FILE.
C) ADDITIONAL TORSIONAL MOMENT FOR EACH MODE SHAPE AT EACH
FLOOR LEVEL ARE WRITTEN IN _DIATOR.TXT FILE.
_

_MODAL BASE ACTIONS_

MODAL BASE ACTIONS FORCES IN KN LENGTH IN METE

-----------------------------------------------------------
MOMENTS ARE ABOUT THE ORIGIN
MODE PERIOD FX FY FZ MX MY MZ

1 0.854 -12.32 5.46 307.86 2121.61 -2561.69 121.43

2 0.718 44.32 0.07 5.08 27.06 86.13 -299.02
3 0.662 -31.87 1.06 52.78 241.48 -309.26 230.00
4 0.245 -5.07 -0.06 0.50 -0.76 -17.06 -13.66
5 0.215 4.62 -5.21 67.32 -100.01 -358.75 -25.42
6 0.193 1.72 -1.28 3.93 0.77 5.93 1.81
7 0.138 -6.82 -0.42 0.75 1.97 -21.17 -3.83
8 0.128 7.58 -0.60 1.29 3.29 12.62 -0.16
9 0.124 -2.81 -0.74 2.18 4.84 -34.05 -7.14
10 0.102 0.04 -6.24 0.53 16.27 -7.66 -68.07

_PARTICIPATION FACTORS_

MASS PARTICIPATION FACTORS IN PERCENT BASE SHEAR IN KN

-------------------------------------- ------------------

MODE X Y Z SUMM-X SUMM-Y SUMM-Z X Y Z

1 0.10 0.02 59.22 0.098 0.018 59.221 0.00 0.00 307.86

2 64.75 0.00 0.82 64.852 0.018 60.044 0.00 0.00 5.08
3 2.97 0.00 7.87 67.825 0.021 67.914 0.00 0.00 52.78
4 6.50 0.00 0.06 74.326 0.022 67.975 0.00 0.00 0.50
5 0.04 0.05 8.25 74.367 0.070 76.227 0.00 0.00 67.32
 6 0.10 0.05 0.48
74.462 0.119 76.709 0.00 0.00 3.93
7 7.88 0.03 0.09
82.341 0.146 76.801 0.00 0.00 0.75
8 5.67 0.03 0.16
88.007 0.180 76.959 0.00 0.00 1.29
9 0.46 0.03 0.27
88.467 0.210 77.225 0.00 0.00 2.18
10 0.00 8.63 0.0788.468 8.843 77.291 0.00 0.00 0.53
---------------------------
TOTAL SRSS SHEAR 0.00 0.00 319.60
TOTAL 10PCT SHEAR 0.00 0.00 320.45
TOTAL ABS SHEAR 0.00 0.00 442.22
TOTAL CSM SHEAR 0.00 0.00 321.21
TOTAL CQC SHEAR 0.00 0.00 328.39

_ DXF IMPORT OF EI LOCATION HUT.DXF -- PAGE NO. 22

*********************************************************
* UNITS - KN METE *
* TIME PERIOD FOR Z 1893 LOADING = 0.40300 SEC *
* SA/G PER 1893= 2.500, LOAD FACTOR= 1.000 *
* FACTOR V PER 1893= 0.0468 X 3934.21 *
* VB Min based on Clause 7.2.2 = 43.28 *
*********************************************************

355. LOAD LIST 11 TO 59

356. FINISH

*********** END OF THE STAAD.Pro RUN ***********

**** DATE= JAN 25,2025 TIME= 13:23: 9 ****

************************************************************
* For technical assistance on STAAD.Pro, please visit *
* http://www.bentley.com/en/support/ *
* *
* Details about additional assistance from *
* Bentley and Partners can be found at program menu *
* Help->Technical Support *
* *
* Copyright (c) 1997-2017 Bentley Systems, Inc. *
* http://www.bentley.com *
************************************************************