0% found this document useful (0 votes)
47 views93 pages

Ccna Image Ques

The document contains multiple-choice questions related to networking concepts, configurations, and troubleshooting scenarios involving routers and switches. It covers topics such as routing protocols, VLAN configurations, NAT translations, and access control lists. Each question provides several options for the correct answer, indicating a focus on practical networking knowledge and skills.

Uploaded by

forfuture670
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
47 views93 pages

Ccna Image Ques

The document contains multiple-choice questions related to networking concepts, configurations, and troubleshooting scenarios involving routers and switches. It covers topics such as routing protocols, VLAN configurations, NAT translations, and access control lists. Each question provides several options for the correct answer, indicating a focus on practical networking knowledge and skills.

Uploaded by

forfuture670
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 93

15. Refer to the exhibit.

Which prefix does Router 1 use for

traffic to Host A?

 A. 10.10.10.0/28
 B. 10.10.13.0/25
 C. 10.10.13.144/28
 D. 10.10.13.208/29

20. Refer to the exhibit. What is


the effect of this configuration?

 A. The switch port interface trust


state becomes untrusted.
 B. The switch port remains administratively down until the interface is
connected to another switch.
 C. Dynamic ARP inspection is disabled because the ARP ACL is missing.
D. The switch port remains down until it is configured to trust or untrust incoming
packets.

24. Refer to the exhibit. Which password must an engineer use


to enter the enable mode?

 A. adminadmin123
 B. default
 C. testing1234
 D. cisco123

26. Which output displays a JSON


data representation?

 A. Option A
 B. Option B
 C. Option C
 D. Option D
. Refer to Exhibit. How does SW2 interact with other switches
in this VTP domain?

 A. It processes VTP updates from any VTP clients on the network on its
access ports.
 B. It receives updates from all VTP servers and forwards all locally
configured VLANs out all trunk ports.
 C. It forwards only the VTP advertisements that it receives on its trunk
ports.
 D. It transmits and processes VTP updates from any VTP Clients on the
network on its trunk ports

Refer to the exhibit. What is the effect of this configuration?

 A. All ARP packets are dropped by the switch.


 B. Egress traffic is passed only if the destination is a DHCP server.
 C. All ingress and egress traffic is dropped because the interface is
untrusted.
 D. The switch discard all ingress ARP traffic with invalid MAC-to-IP
address bindings

. Refer to the exhibit. An engineer configured NAT translations


and has verified that the configuration is correct. Which IP
address is the source IP?
 A. 10.4.4.4
 B. 10.4.4.5
 C. 172.23.103.10
 D. 172.23.104.4

Refer to the exhibit. Which route does R1 select for traffic that
is destined to 192 168.16.2?

 A. 192.168.16.0/21
 B. 192.168.16.0/24
 C. 192.168 26.0/26
 D. 192.168.16.0/27

A. The trunk does not form and the ports go into an err-disabled status.
 B. The trunk forms but the mismatched native VLANs are merged into a
single broadcast domain.
 C. The trunk does not form, but VLAN 99 and VLAN 999 are allowed to
traverse the link.
 D. The trunk forms but VLAN 99 and VLAN 999 are in a shutdown state.
. Refer to the exhibit. The show ipospf interface command has been
executed on R1. How is OSPF configured?

 A. The interface is not participating in OSPF.


 B. A point-to-point network type is configured.
 C. The default Hello and Dead timers are in use.
 D. There are six OSPF neighbors on this interface
Refer to the exhibit. An engineer is bringing up a new circuit to the
MPLS provider on the Gi0/1 interface of Router1.

The new circuit uses eBGP and teams the route to VLAN25 from the
BGP path. What is the expected behavior for the traffic flow for route
10.10.13.0/25?

 A. Traffic to 10.10.13.0.25 is load balanced out of multiple interfaces


 B.Route 10.10.13.0/25 is updated in the routing table as being learned
from interface Gi0/1.
 C. Traffic to 10.10.13.0/25 is a symmetrical
 D.Route 10.10.13.0/25 learned via the Gi0/0 interface remains in the
routing table

 Refer to the exhibit. Which type of route does R1 use to reach
host 10.10.13.10/32?

A. floating static route


 B. host route
 C. default route
 D. network route
Refer to the exhibit. A network engineer must block access for all
computers on VLAN 20 to the web server via HTTP. All other computers
must be able to access the web server. Which configuration when applied
to switch A accomplishes this task?

A. Option A
 B. Option B
 C. Option C
 D. Option D
Refer to the exhibit. Based on the LACP neighbor status, in which mode
is the SW1 port channel configured?

 A. passive
 B. mode on
 C. auto
 D. active
Refer to Exhibit. An engineer is configuring the NEW York router to
reach the Lo1 interface of the Atlanta router using interface Se0/0/0 as
the primary path. Which two commands must be configured on the
New York router so that it can reach the Lo1 interface of the Atlanta
router via Washington when the link between New York and Atlanta
goes down? (Choose two)

 A. ipv6 router 2000::1/128 2012::1


 B. ipv6 router 2000::1/128 2012:1 5
 C. ipv6 router 2000::1/128 2012::2
 D. ipv6 router 2000::1/128 2023:2 5
 E. ipv6 router 2000::1/128 2023::3 5

Refer to the exhibit. Which command provides this output?

 A. show ip route
 B. show ip interface
 C. show interface
 D. show cdpneighbor
Refer to the exhibit. The New York router is configured with static
routes pointing to the Atlanta and Washington sites. Which two tasks
must be performed so that the Serial0/0/0 interfaces on the Atlanta
and Washington routers can reach one another? (Choose two.)

 A.
Configure the ipv6 route 2012::/126 2023::1 command on the
Washington router.
 B.Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta
router.
 C.Configure the Ipv6 route 2012::/126 s0/0/0 command on the Atlanta
router.
 D.Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta
router.
 E.
Configure the ipv6 route 2012::/126 2023::2 command on the
Washington router
Refer to exhibit. Which statement explains the configuration error
message that is received?

 A. It is a broadcast IP address.
 B. The router does not support/28 mask.
 C. It belongs to a private IP address range.
 D. It is a network IP address

Refer to the exhibit. What does router R1 use as its OSPF router-ID?

 A. 10.10.1.10
 B. 10.10.10.20
 C. 172.16.15.10
 D. 192.168.0.1
Refer to the exhibit. If OSPF is running on this network, how does
Router 2 handle traffic from Site B to 10.10.13.128/25 at Site A?

 A. It sends packets out of interface Fa0/2 only.


 B. It sends packets out of interface Fa0/1 only.
 C. It cannot send packets to 10.10.13.128/25.
 D. It load-balances traffic out of Fa0/1 and Fa0/2
Refer to the exhibit. An extended ACL has been configured and applied
to router R2 The configuration started to work as intended.Which two
changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20.0/26
from the 10.0.10.0/26 subnet while still allowing all other traffic?

(Choose two)

 A.Add a “permit ip any any” statement to the begining of ACL 101 for
allowed traffic.
 B.Add a “permit ip any any” statement at the end of ACL 101 for allowed
traffic.
 C. The source and destination IPs must be swapped in ACL 101.
 D. The ACL must be configured the Gi0/2 interface inbound on R1.
 E. The ACL must be moved to the Gi0/1 interface outbound on R2
. Refer to the exhibit. With which metric was the route to host
172.16.0.202 learned?

 A. 0
 B. 110
 C. 38443
 D. 3184439

Refer to the exhibit. If configuring a static default route on the router


with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command, how does the
router respond?
 A.It ignores the new static route until the existing OSPF default route is
removed.
 B.It immediately replaces the existing OSPF route in the routing table with
the newly configured static route.
 C. It starts load-balancing traffic between the two default routes.
 D.It starts sending traffic without a specific matching entry in the routing
table to GigabitEthernet0/1

Refer to the Exhibit. After the switch configuration the ping test fails
between PC A and PC B Based on the output for switch 1. Which error
must be corrected?

 A. There is a native VLAN mismatch.


 B. Access mode is configured on the switch ports.
 C. The PCs are in the incorrect VLAN.
 D. All VLANs are not enabled on the trunk
. Refer to the exhibit. A network administrator is configuring an
EtherChannel between SW1 and SW2. The SW1 configuration is
shown. What is the correct configuration for SW2?

 A.interface FastEthernet 0/1


channel-group 1 mode active
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet 0/2
channel-group 1 mode active
switchport trunk encapsulation dot1q
switchport mode trunk
 B.interface FastEthernet 0/1
channel-group 2 mode auto
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet 0/2
channel-group 2 mode auto
switchport trunk encapsulation dot1q
switchport mode trunk
 C.interface FastEthernet 0/1
channel-group 1 mode desirable
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet 0/2
channel-group 1 mode desirable
switchport trunk encapsulation dot1q
switchport mode trunk
 D.interface FastEthernet 0/1
channel-group 1 mode passive
switchport trunk encapsulation
dot1q switchport mode trunk
interface FastEthernet 0/2
channel-group 1 mode passive
switchport trunk encapsulation dot1q
switchport mode trunk

Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent to switch


S2 where the frame is received on VLAN 2. What causes this behavior?
A. trunk mode mismatches
 B. allowing only VLAN 2 on the destination
 C. native VLAN mismatches
 D. VLANs that do not correspond to a unique IP subnet

105. Refer to the exhibit. The MAC address table is shown in its
entirety. The Ethernet frame that is shown arrives at the switch. What
two operations will the switch perform when it receives this frame?
(Choose two.)

 A. The switch will not forward a frame with this destination MAC address.
 B. The frame will be forwarded out of all the ports on the switch.
 C. The MAC address of ffff.ffff.ffff will be added to the MAC address table.
 D.The frame will be forwarded out of all the active switch ports except for
port fa0/0.
 E.
The MAC address of 0000.00aa.aaaa will be added to the MAC
Address Table.
 F. The frame will be forwarded out of fa0/0 and fa0/1 only

106. Refer to the exhibit. Which switch in this configuration becomes


the root bridge?

 A. SW1
 B. SW2
 C. SW3
 D. SW4

107. Refer to the exhibit. Which two statements are true about the
loopback address that is configured on RouterB? (Choose two.)
 A. It ensures that data will be forwarded by RouterB.
 B. It provides stability for the OSPF process on RouterB.
 C. It specifies that the router ID for RouterB should be 10.0.0.1.
 D. It decreases the metric for routes that are advertised from RouterB.
 E. It indicates that RouterB should be elected the DR for the LAN.

Refer to the exhibit. Which two statements about the interface that
generated the output are true? (Choose two.)

 A. Two secure MAC address are manually configured on the interface.


 B.
A syslog message is generated when the maximum number of secure
MAC addresses is on the interface.
 C. The interface is error-disabled.
 D. The interface dynamically learned two secure MAC addresses.
 E.An SNMP trap is generated when the maximum number of secure MAC
addresses is reached on the interface

Refer to the exhibit. Which two statements about the interface that
generated the output are true? (Choose two.)
 A. learned MAC addresses are deleted after five minutes of inactivity
 B.the interface is error-diabled if packets arrive from a new unknown
source address
 C. it has dynamically lerned two secure MAC addresses
 D. it has dynamically learned three secure MAC addresses
 E.the security violation counter increments if packets arrive from a new
unknown source address

Refer to the exhibit. Which two events occur on the interface, if


packets from an unknown Source address arrive after the interface
learns the maximum number of secure MAC address? (Choose two.)

 A. The security violation counter dose not increment


 B. The port LED turns off
 C. The interface is error-disabled
 D. A syslog message is generated
 E. The interface drops traffic from unknown MAC address
Refer to the exhibit. Which two statements about the network
environment of router R1 must be true? (Choose two.)

.
 Athere are
20 different
network
masks
within the
10.0.0.0/8
network
 B. A static
default
route to
10.85.33.14
was defined
 C. Ten
routes are
equally
load-
balanced
between
Te0/1/0.100
and
Te0/2/0.100
 D. The 10.0.0.0/8 network was learned via external EIGRP
 E. The EIGRP administrative distance was manually changed from 90 to
170

Refer to the exhibit. Which statement about the interface that


generated the output is true?
 A. Five secure MAC addresses are dynamically learned on the interface.
 B. A syslog message is generated when a violation occurs.
 C. One secure MAC address is manually configured on the interface.
 D. One secure MAC address is dynamically configured on the interface
Refer to the exhibit. When PC 1 sends a packet to PC2,the packet has.
Which source and destination IP address when it arrives at interface
Gi0/0 on router R2?

A. source 192.168.10.10 and destination 10.10.2.2


 B. source 192.168.20.10 and destination 192.168.20.1
 C. source 192.168.10.10 and destination 192.168.20.10
 D. source 10.10.1.1 and destination 10.10.2.2
Refer to the exhibit Users in your office are complaining that they
cannot connect to the severs at a remote site. When troubleshooting,
you find that you can successfully reach the severs from router R2.
What is the most likely reason that the other users are experiencing
connection failure?

 A. interface ports are shut down on the remote servers


 B. The DHCP address pool has been exhausted
 C.The ip helper-address command is missing on the R2 interface that
connects to the switch
 D.VLSM is misconfigured between the router interface and the DHCP
pool.
Refer to the exhibit. The default-information originate command is
configured under the R1 OSPF configuration. After testing, workstations
on VLAN 20 at Site B cannot reach a DNS server on the Internet.
Which action corrects the configuration issue?

 A. Add the default-information originate command on R2.


 B.Add the always keyword to the default-information originate command
on R1.
 C. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.18 command on R1.
 D. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.2 command on R2.

Which of the following is the JSON encoding of a dictionary or hash?


 A. {“key”:”value”}

 B. [“key”,”value”]
 C. {“key”,”value”}
 D. (“key”:”value”)
Refer to the exhibit. If R1 receives a packet destined to 172.16.1.1, to
which IP address does it send the packet?

 A. 192.168.14.4
 B. 192.168.12.2
 C. 192.168.13.3
 D. 192.168.15.5

Refer to the exhibit. If RTR01 is configured as shown, which three


addresses will be received by other routers that are running EIGRP on
the network? (Choose three)
 A. 192.168.2.0
 B. 10.4.3.0
 C. 10.0.0.0
 D. 172.16.0.0
 E. 172.16.4.0
 F. 192.168.0.0

. Refer to the exhibit. After you apply the given configuration to


arouter, the DHCP clients behind the device connot communicate with
hosts outside of their subnet. Which action is most likely to correct the

problem?

 A. Configure the dns server on the same subnet as the clients


 B. Activate the dhcp pool
 C. Correct the subnet mask
 D. configure the default gateway
. Refer to the exhibit. How will the router handle a packet destined for

192.0.2.156?

 A. The router will forward the packet via either Serial0 or Serial1.
 B. The router will return the packet to its source.
 C. The router will forward the packet via Serial2.
 D. The router will drop the packet
158. Refer to the exhibit. How will switch SW2 handle traffic from VLAN
10 on SW1?

 A. It sends the traffic to VLAN 10.


 B. It sends the traffic to VLAN 100.
 C. It drops the traffic.
 D. It sends the traffic to VLAN 1.
. Refer to the exhibit. On R1 which routing protocol is in use on the
route to 192.168.10.1?

 A. RIP
 B. OSPF
 C. IGRP
 D. EIGRP
167. Refer to the exhibit. Which VLAN ID is associated with the default
VLAN in the given environment?

 A. VLAN 1
 B. VLAN 5
 C. VLAN 10
 D. VLAN 20

Refer to the exhibit. After you apply the give configurations to R1 and
R2 you notice that OSPFv3 fails to start. Which reason for the problem
is most likely true ?
A. The area numbers on R1 and R2 are mismatched
 B. The IPv6 network addresses on R1 and R2 are mismatched
 C. The autonomous system numbers on R1 and R2 are mismatched
 D. The router ids on R1 and R2 are mismatched

Refer to the exhibit. Which feature is enabled by this configuration?

 A. static NAT translation


 B. a DHCP pool
 C. a dynamic NAT address pool
 D. PAT

Refer to the exhibit. Which Command do you enter so that R1


advertises the loopback0 interface to the BGP Peers?
 A. Network 172.16.1.32 mask 255.255.255.224
 B. Network 172.16.1.0 0.0.0.255
 C. Network 172.16.1.32 255.255.255.224
 D. Network 172.16.1.33 mask 255.255.255.224
 E. Network 172.16.1.32 mask 0.0.0.31
 F. Network 172.16.1.32 0.0.0.31

190. Refer to the exhibit. C-router is to be used as a “router-on-a-stick”


to route between the VLANs. All the interfaces have been properly
configured and IP routing is operational. The hosts in the VLANs have
been configured with the appropriate default gateway. What is true
about this configuration?


 A. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
 B. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255
 C. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
 D. No further routing configuration is required
Refer to the exhibit. Which address and mask combination represents
a summary of the routes learned by EIGRP?

 A. 192.168.25.0 255.255.255.240
 B. 192.168.25.0 255.255.255.252
 C. 192.168.25.16 255.255.255.240
 D. 192.168.25.16 255.255.255.252
 E. 192.168.25.28 255.255.255.240
 F. 192.168.25.28 255.255.255.252
. Refer to the exhibit. A network associate has configured OSPF with
the command:

City(config-router)# network 192.168.12.64 0.0.0.63 area 0.

After completing the configuration, the associate discovers that not all
the interfaces are participating in OSPF. Which three of the interfaces
shown in the exhibit will participate in OSPF according to this
configuration statement? (Choose three.)

 A. FastEthernet0 /0
 B. FastEthernet0 /1
 C. Serial0/0
 D. Serial0/1.102
 E. Serial0/1.103
 F. Serial0/1.104
194. A network administrator is troubleshooting the OSPF configuration
of routers R1 and R2. The routers cannot establish an adjacency
relationship on their common Ethernet link. The graphic shows the
output of the show ipospf interface e0 command for routers R1 and R2.
Based on the information in the graphic, what is the cause of this
problem?

 A. The OSPF area is not configured properly.


 B. The OSPF area is not configured properly.
 C. The cost on R1 should be set higher.
 D. The hello and dead timers are not configured properly.
 E. A backup designated router needs to be added to the network.
 F. The OSPF process ID numbers must match
Refer to the graphic. R1 is unable to establish an OSPF neighbor
relationship with R3. What are possible reasons for this problem?
(Choose two.)

 A. All of the routers need to be configured for backbone Area 1.


 B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor
adjacency with R3.
 C. A static route has been configured from R1 to R3 and prevents the
neighbor adjacency from being established.
 D. The hello and dead interval timers are not set to the same values on R1
and R3.
 E. EIGRP is also configured on these routers with a lower administrative
distance.
 F. R1 and R3 are configured in different areas
Refer to the exhibit. Given the output for this command, if the router ID
has not been manually set, what router ID will OSPF use for this router?

 A. 10.1.1.2

 B. 10.154.154.1
 C. 172.16.5.1
 D. 192.168.5.3

Refer to the exhibit. When running EIGRP, what is required for RouterA
to exchange routing updates with RouterC?
 A. AS numbers must be changed to match on all the routers
 B. Loopback interfaces must be configured so a DR is elected
 C. The no auto-summary command is needed on Router A and Router C
 D.Router B needs to have two network statements, one for each
connected network
.

Refer to the exhibit. Which rule does the DHCP server use when there
is an IP address conflict?

 A. The address is removed from the pool until the conflict is resolved.
 B. The address remains in the pool until the conflict is resolved.
 C. Only the IP detected by Gratuitous ARP is removed from the pool.
 D. Only the IP detected by Ping is removed from the pool.
 E. The IP will be shown, even after the conflict is resolved
199. Refer to the exhibit. A network technician is asked to design a
small network with redundancy. The exhibit represents this design,
with all hosts configured in the same VLAN. What conclusions can be
made about this design?

 A. This design will function as intended.


 B. Spanning-tree will need to be used.
 C. The router will not accept the addressing scheme.
 D. The connection between switches should be a trunk.
 E. The router interfaces must be encapsulated with the 802.1Q protocol

Refer to the exhibit. Router R1 is running three different routing


protocols. Which route characteristic is used by the router to forward
the packet that it receives for destination IP 172.16.32.1?

 A. longest prefix
 B. metric
 C. cost
 D. administrative distance

. Refer to the exhibit. An engineer is bringing up a new circuit to the


MPLS provider on the Gi0/1 interface of Router1.The new circuit uses
eBGP and teams the route to VLAN25 from the BGP path. What is the
expected behavior for the traffic flow for route 10.10.13.0/25?
 A. Traffic to 10.10.13.0.25 is load balanced out of multiple interfaces
 B.Route 10.10.13.0/25 is updated in the routing table as being learned
from interface Gi0/1.
 C. Traffic to 10.10.13.0/25 is asymmeteical
 D.Route 10.10.13.0/25 learned via the GiO/0 interface remains in the
routing table

. Refer to the exhibit. How does router R1 handle traffic to

192.168.10.16?

 A.It selects the IS-IS route because it has the shortest prefix inclusive of
the destination address.
 B.It selects the EIGRP route because it has the lowest administrative
distance.
 C. It selects the OSPF route because it has the lowest cost.
 D.It selects the RIP route because it has the longest prefix inclusive of the
destination address
Which two commands were used to create port channel 10? (Choose
two )

 A. Option A
 B. Option B
 C. Option C
 D. Option D
 E. Option E
. Refer to the exhibit. How does the router manage traffic to
192.168.12.16?

 A.It selects the RIP route because it has the longest prefix inclusive of the
destination address.
 B.It chooses the OSPF route because it has the longest prefix inclusive of
the destination address.
 C. It load-balances traffic between all three routes
 D.It chooses the EIGRP route because it has the lowest administrative
distance

Refer to the exhibit. An administrator configures four switches for local


authentication using passwords that are stored in a cryptographic
hash. The four switches must also support SSH access for
administrators to manage the network infrastructure. Which switch is
configured correctly to meet these requirements?

 A. SW1
 B. SW2
 C. SW3
 D. SW4
Refer to the exhibit. What two conclusions should be made about this
configuration? (Choose two )

 A. The designated port is FastEthernet 2/1


 B. This is a root bridge
 C. The spanning-tree mode is Rapid PVST+
 D. The spanning-tree mode is PVST+
 E. The root port is FastEthernet 2/1
Refer to the exhibit. A router reserved these five routes from different
routing information sources. Which two routes does the router install in
its routing table?
(Choose two)

 A. RIP route 10.0.0.0/30


 B. iBGP route 10.0.0.0/30
 C. OSPF route 10.0.0.0/30
 D. EIGRP route 10.0.0.1/32
 E. OSPF route 10.0.0.0/16
. Refer to the exhibit. The network administrator wants VLAN 67 traffic
to be untagged between Switch 1 and Switch 2 while all other VLANs
are to remain tagged. Which command accomplishes this task?

 A. switchport access vlan 67


 B. switchport trunk allowed vlan 67
 C. switchport private-vlan association host 67
 D. switchport trunk native vlan 67
230. Refer to the exhibit. Refer to the exhibit. After the
configuration is applied, the two routers fail to establish an
OSPF neighbor relationship. what is the reason for the
problem?

 A. The OSPF router IDs are mismatched.


 B. Router2 is using the default hello timer.
 C. The network statement on Router1 is misconfigured.
 D. The OSPF process IDs are mismatched
. Refer to the exhibit. Router R1 Fa0/0 cannot ping router R3
Fa0/1. Which action must be taken in router R1 to help resolve

the configuration issue?

 A. set the default network as 20.20.20.0/24


 B. set the default gateway as 20.20.20.2
 C. configure a static route with Fa0/1 as the egress interface to reach the
20.20.20.0/24 network
 D.configure a static route with 10.10.10.2 as the next hop to reach the
20.20.20.0/24 network

. Refer to the exhibit. Refer to the exhibit. An engineer must


add a subnet for a new office that will add 20 users to the
network. Which IPv4 network and subnet mask combination
does the engineer assign to minimize wasting addresses?

 A. 10.10.225.48 255.255.255.240
 B. 10.10.225.32 255.255.255.240
 C. 10.10.225.48 255.255.255.224
 D. 10.10.225.32 255.255.255.224

235. A corporate office uses four floors in a building


* Floor 1 has 24 users
* Floor 2 has 29 users
* Floor 3 has 28 users
* Floor 4 has 22 users
Which subnet summarizes and gives the most efficient
distribution of IP addresses for the router configuration?
 A. 192.168.0.0/26 as summary and 192.168.0.0/29 for each floor
 B. 192.168.0.0/24 as summary and 192.168.0.0/28 for each floor
 C. 192.168.0.0/23 as summary and 192.168.0.0/25 for each floor
 D. 192.168.0.0/25 as summary and 192.168.0.0/27 for each floor
Refer to the exhibit. Which configuration issue is preventing the OSPF
neighbor relationship from being established between the two routers
 A. R2 is using the passive-interface default command
 B. R1 has an incorrect network command for interface Gi1/0
 C. R2 should have its network command in area 1
 D. R1 interface Gi1/0 has a larger MTU size

Refer to the exhibit. Which action is expected from SW1 when


the untagged frame is received on the GigabitEthernet0/1
interface?

 A. The frame is processed in VLAN 5.


 B. The frame is processed in VLAN 11
 C. The frame is processed in VLAN 1
 D. The frame is dropped
. Refer to the exhibit. Which route type is configured to reach
the internet?

 A. floating static route


 B. host route
 C. default route
 D. network route
Refer to the exhibit. To which device does Router1 send packets that are
destined to host 10.10.13.165?

 A. Router2
 B. Router3
 C. Router4
 D. Router5

Refer to the exhibit. Which two commands were used to create


port channel 10? (Choose two.)
A. int range g0/0-1
channel-group 10 mode active
B. int range g0/0-1
channel-group 10 mode desirable
C. int range g0/0-1
channel-group 10 mode passive
D. int range g0/0-1
channel-group 10 mode auto
E. int range g0/0-1
channel-group 10 mode on

Refer to the exhibit. An administrator is tasked with


configuring a voice VLAN. What is the expected outcome when
a Cisco phone is connected to the GigabitEthernet 3/1/4 port
on a switch?

 A. The phone and a workstation that is connected to the phone do not


have VLAN connectivity.
 B. The phone sends and receives data in VLAN 50, but a workstation
connected to the phone sends and receives data in VLAN 1.
 C. The phone sends and receives data in VLAN 50, but a workstation
connected to the phone has no VLAN connected.
 D. The phone and a workstation that is connected to the phone send and
receive data in VLAN 50.
262. Refer to the exhibit. An engineer deploys a topology in
which R1 obtains its IP configuration from DHCP. If the switch
and DHCP server configurations are complete and correct.
Which two sets of commands must be configured on R1 and R2

to complete the task? (Choose two)

A.
R1(config)# interface fa0/0
R1(config-if)# ip helper-address 198.51.100.100
B.
R2(config)# interface gi0/0
R2(config-if)# ip helper-address 198.51.100.100
C.
R1(config)# interface fa0/0
R1(config-if)# ip address dhcp
R1(config-if)# no shutdown
D.
R2(config)# interface gi0/0
R2(config-if)# ip address dhcp
E.
R1(config)# interface fa0/0
R1(config-if)# ip helper-address 192.0.2.2
Correct Answer: BC
263. Refer to the exhibit. What commands are needed to add a
subinterface to Ethernet0/0 on R1 to allow for VLAN 20, with IP

address 10.20.20.1/24?

A.
R1(config)#interface ethernet0/0
R1(config)#encapsulation dot1q 20
R1(config)#ip address 10.20.20.1 255.255.255.0
B.
R1(config)#interface ethernet0/0.20
R1(config)#encapsulation dot1q 20
R1(config)#ip address 10.20.20.1 255.255.255.0
C.
R1(config)#interface ethernet0/0.20
R1(config)#ip address 10.20.20.1 255.255.255.0
D.
R1(config)#interface ethernet0/0
R1(config)#ip address 10.20.20.1 255.255.255.0

Refer to the exhibit. If the network environment is operating


normally, which type of device must be connected to interface
FastEthernet 0/1?

 A. DHCP client
 B. access point
 C. router
 D. PC
 267. Refer to the exhibit. Which configuration on RTR-1
denies SSH access from PC-1 to any RTR-1 interface and
allows all other traffic?

A.
access-list 100 deny tcp host 172.16.1.33 any eq 22
access-list 100 permit ip any any
 interface GigabitEthernet0/0
ip access-group 100 in
 B.
access-list 100 deny tcp host 172.16.1.33 any eq 22
access-list 100 permit ip any any
 line vty 0 15
access-class 100 in
 C.
access-list 100 deny tcp host 172.16.1.33 any eq 23
access-list 100 permit ip any any
 interface Gigabit Ethernet0/0
ip access-group 100 in
 D.
access-list 100 deny tcp host 172.16.1.33 any eq 23
access-list 100 permit ip any any
 line vty 0 15
access-class 100 in
Refer to the exhibit. An administrator configures the following
ACL in order to prevent devices on the 192.168.1.0 subnet
from accessing the server at 10.1.1.5:

access-list 100 deny ip 192.168.1.0 0.0.0.255 host 10.1.1.5

access-list 100 permit ip any any

Where should the administrator place this ACL for the most
efficient use of network resources?
 A. inbound on router A Fa0/0
 B. outbound on router B Fa0/0
 C. outbound on router A Fa0/1
 D. inbound on router B Fa0/1

Refer to the exhibit. Router R1 is configured with static NAT.


Addressing on the router and the web server are correctly
configured, but there is no connectivity between the web
server and users on the Internet. What is a possible reason for
this lack of connectivity?

 A. The router NAT configuration has an incorrect inside local address.


 B. The inside global address is incorrect.
 C. The NAT configuration on interface S0/0/1 is incorrect.
 D. Interface Fa0/0 should be configured with the command ipnat outside

Refer to the exhibit. Which two configurations would be used


to create and apply a standard access list on R1, so that only
the 10.0.70.0/25 networkdevices are allowed to access the
internal database server? (Choose
two.)

 A.
R1(config)# interface GigabitEthernet0/0
R1(config-if)# ip access-group 5 out
 B.
R1(config)# access-list 5 permit 10.0.54.0 0.0.1.255
 C.
R1(config)# interface Serial0/0/0
R1(config-if)# ip access-group 5 in
 D.
R1(config)# access-list 5 permit 10.0.70.0 0.0.0.127
 E.
R1(config)# access-list 5 permit any

. Refer to the exhibit. If the switch reboots and all routers have
to re-establish OSPF adjacencies, which routers will become
the new DR and BDR?
 A. Router R3 will become the DR and router R1 will become the BDR.
 B. Router R4 will become the DR and router R3 will become the BDR.
 C. Router R1 will become the DR and router R2 will become the BDR.
 D. Router R3 will become the DR and router R2 will become the BDR.
Refer to the exhibit. Which path is used by the router for
internet traffic?

 A. 209.165.200.0/27
 B. 10.10.10.0/28
 C. 0.0.0.0/0
 D. 10.10.13.0/24
Refer to Exhibit. The loopback1 interface of the Atlanta router
must reach the loopback3 interface of the Washington router.
Which two static host routes must be configured on the NEW

York router? (Choose two)

 A. ipv6 route 2000::1/128 2012::1


 B. ipv6 route 2000::3/128 2023::3
 C. ipv6 route 2000::3/128 s0/0/0
 D. ipv6 route 2000::1/128 2012::2
 E. ipv6 route 2000::1/128 s0/0/

. Refer to the exhibit. A packet is being sent across router R1


to host 172.16.3.14. To which destination does the router send
the packet?
A. 207.165.200.246 via Serial0/1/0
 B. 207.165.200.254 via Serial0/0/0
 C. 207.165.200.254 via Serial0/0/1
 D. 207.165.200.250 via Serial0/0/0

Refer to the exhibit. A network administrator assumes a task


to complete the connectivity between PC A and the File Server
Switch A and Switch B have been partially configured with
VLANs 10, 11, 12, and 13 What is the next step in the
configuration?

 A. Add PDA to VLAN 10 and the File Server to VLAN 11 for VLAN
segmentation
 B. Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN
propagation
 C. Add a router on a stick between Switch A and Switch B allowing for
Inter VLAN routing
 D. Add PC A to the same subnet as the File Server allowing for intra-VLAN
communication

Refer to the exhibit Which outcome is expected when PC_A


sends data to PC_B?

 A. The switch rewrites the source and destination MAC addresses with its
own
 B. The source and destination MAC addresses remain the same
 C. The source MAC address is changed
 D. The destination MAC address is replaced with ffff.ffff.ffff

. Refer to the exhibit. Which switch becomes the root bridge?

 A. S1
 B. S2
 C. S3
 D. S4

293. Refer to the exhibit. What is the next hop address for
traffic that is destined to host 10.0.1.5?

 A. Loopback 0
 B. 10.0.1.4
 C. 10.0.1.50
 D. 10.0.1.3
296. Refer to the exhibit. What action establishes the OSPF
neighbor relationship without forming an adjacency?

 A. modify priority
 B. modify process ID
 C. modify hello interval
 D. modity network type

297. Refer to the exhibit. An engineer booted a new switch and


applied this configuration via the console port. Which
additional configuration must be applied to allow
administrators to authenticate directly to enable privilege
mode via Telnet using a local username and password?

A.
R1(config)#username admin
R1(config-if)#line vty 0 4
R1(config-line)#password p@ss1234
B.
R1(config)#username admin
R1(config-if)#line vty 0 4
R1(config-line)#password p@ss1234
R1(config-line)#transport input telnet
C.
R1(config)#username admin secret p@ss1234
R1(config-if)#line vty 0 4
R1(config-line)#login local
R1(config)#enable secret p@ss1234
D.
R1(config)#username admin privilege 15 secret p@ss1234
R1(config-if)#line vty 0 4
R1(config-line)#login local

298. Refer to the exhibit. Which switch in this configuration


will be elected as the root bridge?

SW1: 0C:E0:38:00:36:75
SW2: 0C:0E:15:22:05:97
SW3: 0C:0E:15:1A:3C:9D
SW4: 0C:E0:18:A1:B3:19
 A. SW1
 B. SW2
 C. SW3
 D. SW4
Correct Answer: C
299. An engineer is configuring NAT to translate the source
subnet of 10.10.0.0/24 to any of three addresses 192.168.3.1,
192.168.3.2, 192.168.3.3 . Which configuration should be
used?
A.
enable
configure terminal
ipnat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30
route-map permit 10.10.0.0 255.255.255.0
ipnat outside destination list 1 pool mypool
interface g1/1
ipnat inside
interface g1/2
ipnat outside
B.
enable
configure terminal
ipnat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30
access-list 1 permit 10.10.0.0 0.0.0.254
ipnat inside source list 1 pool mypool
interface g1/1
ipnat inside
interface g1/2
ipnat outside
C.
enable
configure terminal
ipnat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30
access-list 1 permit 10.10.0.0 0.0.0.255
ipnat inside source list 1 pool mypool
interface g1/1
ipnat inside
interface g1/2
ipnat outside
D.
enable
configure terminal
ipnat pool mypool 192.168.3.1 192.168.3.3 prefix-length 30
access-list 1 permit 10.10.0.0 0.0.0.255
ipnat outside destination list 1 pool mypool
interface g1/1
ipnat inside
interface g1/2
ipnat outside

300. An office has 8 floors with approximately 30-40 users per


floor .What command must be configured on the router
Switched Virtual Interface to use address space efficiently?
 A. ip address 192.168.0.0 255.255.0.0
 B. ip address 192.168.0.0 255.255.254.0
 C. ip address 192.168.0.0 255.255.255.128
 D. ip address 192.168.0.0 255.255.255.224

Router R2 is configured with multiple routes to reach network


10 1.1.0/24 from router R1. What protocol is chosen by router
R2 to reach the destination network 10.1.1.0/24?
 A. eBGP
 B. static
 C. OSPF
 D. EIGRP
Refer to the exhibit. Which route type does the routing
protocol Code D represent in the output?

 A. internal BGP route


 B. /24 route of a locally configured IP
 C. statically assigned route
 D. route learned through EIGRP

Refer to the exhibit. Which type of configuration is

represented in the output?

 A. Ansible
 B. JSON
 C. Chef
 D. Puppet
Refer to the exhibit. After the election process what is the root
bridge in the HQ LAN?

 A. Switch 1
 B. Switch 2
 C. Switch 3
 D. Switch 4
. Refer to the exhibit. An engineer configured the New York
router with state routes that point to the Atlanta and
Washington sites. When command must be configured on the
Atlanta and Washington routers so that both sites are able to

reach the loopback2 interface on the New York router?

 A. ipv6 route ::/0 Serial 0/0/1


 B. ipv6 route 0/0 Serial 0/0/0
 C. ipv6 route ::/0 Serial 0/0/0
 D. ip route 0.0.0.0.0.0.0.0 Serial 0/0/0
 E. ipv6 route ::/0 2000::2

Refer to the exhibit. A network administrator must permit SSH


access to remotely manage routers in a network. The
operations team resides on the 10.20.1.0/25 network. Which

command will accomplish this task?

 A. access-list 2699 permit udp 10.20.1.0 0.0.0.255


 B. no access-list 2699 deny tcp any 10.20.1.0 0.0.0.127 eq 22
 C.access-list 2699 permit tcp any 10.20.1.0 0.0.0.255 eq 22
 D.no access-list 2699 deny ip any 10.20.1.0 0.0.0.255
Refer to the exhibit. If OSPF Is running on this network, how
does Router2 handle traffic from Site B to 10.10.13.128/25 at
Site A?

 A. It load-balances traffic out of Fa0/1 and Fa0/2.


 B. It is unreachable and discards the traffic.
 C. It sends packets out of interface Fa0/2.
 D. It sends packets out of interface Fa0/1.
357. Refer to the exhibit. Which command configures a floating
static route to provide a backup to the primary link?

 A. ip route 0.0.0.0 0.0.0.0 209.165.202.131


 B. ip route 209.165.201.0 255.255.255.224 209.165.202.130
 C. ip route 0.0.0.0 0.0.0.0 209.165.200.224
 D. ip route 209.165.200.224 255.255.255.224 209.165.202.129 254

Refer to the exhibit. An access list is created to deny Telnet


access from host PC-1 to RTR-1 and allow access from all other
hosts A Telnet attempt from PC-2 gives this message:”%
Connection refused by remote host” Without allowing Telnet
access from PC-1, which action must be taken to permit the
traffic?

 A. Add the access-list 10 permit any command to the


configuration
 B. Remove the access-class 10 in command from line vty 0.4.
 C. Add the ip access-group 10 out command to interface g0/0.
 D. Remove the password command from line vty 0 4.
Refer to the exhibit. PC1 is trying to ping PC3 for the first time
and sends out an ARP to S1. Which action is taken by S1?

 A. It forwards it out G0/3 only


 B. It is flooded out every port except G0/0.
 C. It drops the frame.
 D. It forwards it out interface G0/2 only

Refer to the exhibit. A network administrator has been tasked


with securing VTY access to a router. Which access-list entry
accomplishes this task?

 A. access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10


0.0.0.255 eqssh
 B. access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eqscp
 C. access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eq
telnet
 D. access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10 0.0.0.255 eq
https
Refer to the exhibit. A network administrator has been tasked
with securing VTY access to a router. Which access-list entry
accomplishes this task?

 A. access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10


0.0.0.255 eqssh
 B. access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eqscp
 C. access-list 101 permit tcp 10.11.0 0.0.0.255 172.16.10 0.0.0.255 eq
telnet
 D. access-list 101 permit tcp 10.1.10 0.0.0.255 172.16.10 0.0.0.255 eq
https
Refer to the exhibit. What is the result if Gig1/11 receives an
STP BPDU?

 A. The port transitions to STP blocking


 B. The port transitions to the root port
 C. The port immediately transitions to STP forwarding.
 D. The port goes into error-disable state
Refer to the exhibit. A network engineer must configured
communication between PC A and the File Server. To prevent
interruption for any other communications, which command
must be configured?

 A. Switch trunk allowed vlan 12


 B. Switchport trunk allowed vlan none
 C. Switchport trunk allowed vlan add 13
 D. Switchport trunk allowed vlan remove 10-11

Refer to the exhibit. After running the code in the exhibit,


which step reduces the amount of data that the NETCONF
server returns to the NETCONF client, to only the interface’s

configuration?
 A. Use the Ixml library to parse the data returned by the NETCONF server
for the interface’s configuration.
 B. Create an XML filter as a string and pass it to get_config() method as an
argument.
 C. Create a JSON filter as a string and pass it to the get_config() method
as an argument.
 D. Use the JSON library to parse the data returned by the
NETCONF server for the interface’s configuration.

. Refer to the exhibit. The ntp server 192.168.0.3 command has


been configured on router 1 to make it an NTP client of router
2. Which command must be configured on router 2 so that it
operates in server-only mode and relies only on its internal
clock?

 A. Router2(config)#ntp passive
 B. Router2(config)#ntp server 172.17.0.1
 C. Router2(config)#ntp master 4
 D. Router2(config)#ntp server 192.168.0.2
Refer to Exhibit. Which configuration must be applied to the router that
configures PAT to translate all addresses in VLAN 200 while allowing
devices on VLAN 100 to use their own IP addresses?

 A. Option A
 B. Option B
 C. Option C
 D. Option D
Refer to the exhibit. An administrator must configure
interfaces Gi1/1 and Gi1/3 on switch SW11 PC-1 and PC-2 must
be placed in the Data VLAN and Phone-1 must be placed in the
Voice VLAN Which configuration meets these requirements?
 A. Option A
 B. Option B
 C. Option C
 D. Option D

Refer to the exhibit. Which switch becomes the root of the


spanning tree for VLAN 110?

 A. Switch 1
 B. Switch 2
 C. Switch 3
 D. Switch 4
Refer to the exhibit. An access list is required to permit traffic
from any host on interface G0/0 and deny traffic from interface
G/0/1. Which access list must be applied?

 A. Option A
 B. Option B
 C. Option C
 D. Option D
. Refer to the exhibit. An administrator must turn off the
Cisco Discovery Protocol on the port configured with
address last usable address in the 10.0.0.0/30 subnet.
Which command set meets the requirement?

 A. interface gi0/1
no cdp enable
 B. interface gi0/1
clear cdp table
 C. interface gi0/0
no cdp advertise-v2
 D. interface gi0/0
no cdp run
Refer to the exhibit.

The entire contents of the MAC address table are shown.


Sales-4 sends a data frame to Sales-1.

What does the switch do as it receives the frame from Sales-4?


 A. Perform a lookup in the MAC address table and discard the frame due
to a missing entry.
 B. Insert the source MAC address and port into the
forwarding table and forward the frame to Sales-1.
 C. Map the Layer 2 MAC address to the Layer 3 IP address and forward
the frame.
 D. Flood the frame out of all ports except on the port where Sales-1 is
connected

Refer to the exhibit. Only four switches are participating in the


VLAN spanning-tree process.

Branch-1 priority 614440


Branch-2: priority 39082416
Branch-3: priority 0
Branch-4: root primary
Which switch becomes the permanent root bridge for VLAN 5?
 A. Branch-1
 B. Branch-2
 C.Branch-3
 D. Branch-4

Refer to the exhibit. Shortly after SiteA was connected to SiteB


over a new single-mode fiber path users at SiteA report
intermittent connectivity issues with applications hosted at
SiteB What is the cause of the intermittent connectivity issue?

 A. Interface errors are incrementing


 B. An incorrect SFP media type was used at SiteA
 C. High usage is causing high latency
 D. The sites were connected with the wrong cable type

431. Refer to the exhibit. An engineer must configure


GigabitEthernet1/1 to accommodate voice and data traffic
Which configuration accomplishes this task?

 A. Option A
 B. Option B
 C. Option C
 D. Option D

. A network administrator must to configure SSH for remote


access to router R1 The requirement is to use a public and
private key pair to encrypt management traffic to and from the
connecting client. Which configuration, when applied, meets
the requirements?

 A. Option A
 B. Option B
 C. Option C
 D.
Option D
Refer to the exhibit. Which command must be executed for
Gi1.1 on SW1 to become a trunk port if Gi1/1 on SW2 is
configured in desirable or trunk mode?

 A. switchport mode trunk


 B. switchport mode dot1-tunnel
 C. switchport mode dynamic auto
 D. switchport mode dynamic desirable

You might also like