Lab-4.2 - RIP
Lab-4.2 - RIP
Topology Diagram
Learning Objectives
Upon completion of this lab, you will be able to:
• Cable a network according to the Topology Diagram.
• Erase the startup configuration and reload a router to the default state.
• Perform basic configuration tasks on a router.
• Configure and activate interfaces.
• Configure RIP routing on all routers.
• Verify RIP routing using show and debug commands.
• Reconfigure the network to make it contiguous.
• Observe automatic summarization at boundary router.
• Gather information about RIP processing using the debug ip rip command.
• Configure a static default route.
• Propagate default routes to RIP neighbors.
• Document the RIP configuration.
Scenarios
• Scenario A: Running RIPv1 on Classful Networks
• Scenario B: Running RIPv1 with Subnets and Between Classful Networks
• Scenario C: Running RIPv1 on a Stub Network.
Scenario A: Running RIPv1 on Classful Networks
Topology Diagram
Addressing Table
Step 1: Cable a network that is similar to the one in the Topology Diagram.
You can use any current router in your lab as long as it has the required interfaces shown in the topology.
Note: If you use 1700, 2500, or 2600 routers, the router outputs and interface descriptions will appear
different.
Step 4: Test the PC configuration by pinging the default gateway from the PC.
R1(config)#router rip
R1(config-router)#
R1(config-router)#network 192.168.1.0
R1(config-router)#network 192.168.2.0
R1(config-router)#
The network command:
• Enables RIP on all interfaces that belong to this network. These interfaces will now both send and
receive RIP updates.
• Advertises this network in RIP routing updates sent to other routers every 30 seconds.
When you are finished with the RIP configuration, return to privileged EXEC mode and save the current
configuration to NVRAM.
R1(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
R1#copy run start
Step 3: Configure RIP on the R2 router using the router rip and network commands.
R2(config)#router rip
R2(config-router)#network 192.168.2.0
R2(config-router)#network 192.168.3.0
R2(config-router)#network 192.168.4.0
R2(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
R2#copy run start
When you are finished with the RIP configuration, return to privileged EXEC mode and save the current
configuration to NVRAM.
Step 4: Configure RIP on the R3 router using the router rip and network commands.
R3(config)#router rip
R3(config-router)#network 192.168.4.0
R3(config-router)#network 192.168.5.0
R3(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
R3# copy run start
When you are finished with the RIP configuration, return to privileged EXEC mode and save the current
configuration to NVRAM.
Step 1: Use the show ip route command to verify that each router has all of the networks in the
topology entered in the routing table.
Routes learned through RIP are coded with an R in the routing table. If the tables are not converged as
shown here, troubleshoot your configuration. Did you verify that the configured interfaces are active? Did
you configure RIP correctly? Return to Task 3 and Task 4 to review the steps necessary to achieve
convergence.
R1#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
R2#show ip route
<Output omitted>
R3#show ip route
<Output omitted>
Step 2: Use the show ip protocols command to view information about the routing processes.
The show ip protocols command can be used to view information about the routing processes that
are occurring on the router. This output can be used to verify most RIP parameters to confirm that:
• RIP routing is configured
• The correct interfaces send and receive RIP updates
• The router advertises the correct networks
• RIP neighbors are sending updates
R1#show ip protocols
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 16 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 1, receive any version
Interface Send Recv Triggered RIP Key-chain
FastEthernet0/0 1 2 1
Serial0/0/0 1 2 1
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
192.168.1.0
192.168.2.0
Passive Interface(s):
Routing Information Sources:
Gateway Distance Last Update
192.168.2.2 120
Distance: (default is 120)
R1#
R1 is indeed configured with RIP. R1 is sending and receiving RIP updates on FastEthernet0/0 and
Serial0/0/0. R1 is advertising networks 192.168.1.0 and 192.168.2.0. R1 has one routing information
source. R2 is sending R1 updates.
Step 3: Use the debug ip rip command to view the RIP messages being sent and received.
Rip updates are sent every 30 seconds so you may have to wait for debug information to be displayed.
R1#debug ip rip
R1#RIP: received v1 update from 192.168.2.2 on Serial0/0/0
192.168.3.0 in 1 hops
192.168.4.0 in 1 hops
192.168.5.0 in 2 hops
RIP: sending v1 update to 255.255.255.255 via FastEthernet0/0 (192.168.1.1)
RIP: build update entries
network 192.168.2.0 metric 1
network 192.168.3.0 metric 2
network 192.168.4.0 metric 2
network 192.168.5.0 metric 3
RIP: sending v1 update to 255.255.255.255 via Serial0/0/0 (192.168.2.1)
RIP: build update entries
network 192.168.1.0 metric 1
The debug output shows that R1 receives an update from R2. Notice how this update includes all the
networks that R1 does not already have in its routing table. Because the FastEthernet0/0 interface
belongs to the 192.168.1.0 network configured under RIP, R1 builds an update to send out that interface.
The update includes all networks known to R1 except the network of the interface. Finally, R1 builds an
update to send to R2. Because of split horizon, R1 only includes the 192.168.1.0 network in the update.
Step 4: Discontinue the debug output with the undebug all command.
R1#undebug all
All possible debugging has been turned off
Task 6: Document the Router Configurations
On each router, capture the following command output to a text file and save for future reference:
• Running configuration
• Routing table
• Interface summarization
• Output from show ip protocols
Task 7: Clean Up
Erase the configurations and reload the routers. Disconnect and store the cabling. For PC hosts that are
normally connected to other networks (such as the school LAN or to the Internet), reconnect the
appropriate cabling and restore the TCP/IP settings.