Concrete Mix Design

Introduction
The process of selecting suitable ingredients of concrete and determining their relative amounts with the objective of producing a concrete of the required, strength, durability, and workability as economically as possible, is termed the concrete mix design. The proportioning of ingredient of concrete is governed by the required performance of concrete in 2 states, namely the plastic and the hardened states. If the plastic concrete is not workable, it cannot be properly placed and compacted. The property of workability, therefore, becomes of vital importance. The compressive strength of hardened concrete which is generally considered to be an index of its other properties, depends upon many factors, e.g. quality and quantity of cement, water and aggregates; batching and mixing; placing, compaction and curing. The cost of concrete is made up of the cost of materials, plant and labour. The variations in the cost of materials arise from the fact that the cement is several times costly than the aggregate, thus the aim is to produce as lean a mix as possible. From technical point of view the rich mixes may lead to high shrinkage and cracking in the structural concrete, and to evolution of high heat of hydration in mass concrete which may cause cracking. The actual cost of concrete is related to the cost of materials required for producing a minimum mean strength called characteristic strength that is specified by the designer of the structure. This depends on the quality control measures, but there is no doubt that the quality control adds to the cost of concrete. The extent of quality control is often an economic compromise, and depends on the size and type of job. The cost of labour depends on the workability of mix, e.g., a concrete mix of inadequate workability may result in a high cost of labour to obtain a degree of compaction with available equipment. Requirements of concrete mix design The requirements which form the basis of selection and proportioning of mix ingredients are : a ) The minimum compressive strength required from structural consideration b) The adequate workability necessary for full compaction with the compacting equipment available. c) Maximum water-cement ratio and/or maximum cement content to give adequate durability for the particular site conditions d) Maximum cement content to avoid shrinkage cracking due to temperature cycle in mass concrete.

Types of Mixes

1. Nominal Mixes In the past the specifications for concrete prescribed the proportions of cement, fine and coarse aggregates. These mixes of fixed cement-aggregate ratio which ensures adequate strength are termed nominal mixes. These offer simplicity and under normal circumstances, have a margin of strength above that specified. However, due to the variability of mix ingredients the nominal concrete for a given workability varies widely in strength. 2. Standard mixes The nominal mixes of fixed cement-aggregate ratio (by volume) vary widely in strength and may result in under- or over-rich mixes. For this reason, the minimum compressive strength has been included in many specifications. These mixes are termed standard mixes. IS 456-2000 has designated the concrete mixes into a number of grades as M10, M15, M20, M25, M30, M35 and M40. In this designation the letter M refers to the mix and the number to the specified 28 day cube strength of mix in N/mm2. The mixes of grades M10, M15, M20 and M25 correspond approximately to the mix proportions (1:3:6), (1:2:4), (1:1.5:3) and (1:1:2) respectively. 3. Designed Mixes In these mixes the performance of the concrete is specified by the designer but the mix proportions are determined by the producer of concrete, except that the minimum cement content can be laid down. This is most rational approach to the selection of mix proportions with specific materials in mind possessing more or less unique characteristics. The approach results in the production of concrete with the appropriate properties most economically. However, the designed mix does not serve as a guide since this does not guarantee the correct mix proportions for the prescribed performance. For the concrete with undemanding performance nominal or standard mixes (prescribed in the codes by quantities of dry ingredients per cubic meter and by slump) may be used only for very small jobs, when the 28-day strength of concrete does not exceed 30 N/mm2. No control testing is necessary reliance being placed on the masses of the ingredients. Factors affecting the choice of mix proportions The various factors affecting the mix design are: 1. Compressive strength It is one of the most important properties of concrete and influences many other describable properties of the hardened concrete. The mean compressive strength required at a specific age, usually 28 days, determines the nominal water-cement ratio of the mix. The other factor affecting the strength of concrete at a given age and cured at a prescribed temperature is the degree of

compaction. According to Abrahams law the strength of fully compacted concrete is inversely proportional to the water-cement ratio. 2. Workability The degree of workability required depends on three factors. These are the size of the section to be concreted, the amount of reinforcement, and the method of compaction to be used. For the narrow and complicated section with numerous corners or inaccessible parts, the concrete must have a high workability so that full compaction can be achieved with a reasonable amount of effort. This also applies to the embedded steel sections. The desired workability depends on the compacting equipment available at the site. 3. Durability The durability of concrete is its resistance to the aggressive environmental conditions. High strength concrete is generally more durable than low strength concrete. In the situations when the high strength is not necessary but the conditions of exposure are such that high durability is vital, the durability requirement will determine the water-cement ratio to be used. 4. Maximum nominal size of aggregate In general, larger the maximum size of aggregate, smaller is the cement requirement for a particular water-cement ratio, because the workability of concrete increases with increase in maximum size of the aggregate. However, the compressive strength tends to increase with the decrease in size of aggregate. IS 456:2000 and IS 1343:1980 recommend that the nominal size of the aggregate should be as large as possible. 5. Grading and type of aggregate The grading of aggregate influences the mix proportions for a specified workability and watercement ratio. Coarser the grading leaner will be mix which can be used. Very lean mix is not desirable since it does not contain enough finer material to make the concrete cohesive. The type of aggregate influences strongly the aggregate-cement ratio for the desired workability and stipulated water cement ratio. An important feature of a satisfactory aggregate is the uniformity of the grading which can be achieved by mixing different size fractions. 6. Quality Control The degree of control can be estimated statistically by the variations in test results. The variation in strength results from the variations in the properties of the mix ingredients and lack of control of accuracy in batching, mixing, placing, curing and testing. The lower the difference between the mean and minimum strengths of the mix lower will be the cement-content required. The factor controlling this difference is termed as quality control.

Mix Proportion designations

The common method of expressing the proportions of ingredients of a concrete mix is in the terms of parts or ratios of cement, fine and coarse aggregates. For e.g., a concrete mix of proportions 1:2:4 means that cement, fine and coarse aggregate are in the ratio 1:2:4 or the mix contains one part of cement, two parts of fine aggregate and four parts of coarse aggregate. The proportions are either by volume or by mass. The water-cement ratio is usually expressed in mass Factors to be considered for mix design The grade designation giving the characteristic strength requirement of concrete. The type of cement influences the rate of development of compressive strength of concrete. Maximum nominal size of aggregates to be used in concrete may be as large as possible within the limits prescribed by IS 456:2000. The cement content is to be limited from shrinkage, cracking and creep. The workability of concrete for satisfactory placing and compaction is related to the size and shape of section, quantity and spacing of reinforcement and technique used for transportation, placing and compaction.

Procedure
1. Determine the mean target strength ft from the specified characteristic compressive strength at 28day fck and the level of quality control. ft = fck + 1.65 S where S is the standard deviation obtained from the Table of approximate contents given after the design mix. 2. Obtain the water cement ratio for the desired mean target using the emperical relationship between compressive strength and water cement ratio so chosen is checked against the limiting water cement ratio. The water cement ratio so chosen is checked against the limiting water cement ratio for the requirements of durability given in table and adopts the lower of the two values. 3. Estimate the amount of entrapped air for maximum nominal size of the aggregate from the table. 4. Select the water content, for the required workability and maximum size of aggregates (for aggregates in saturated surface dry condition) from table. 5. Determine the percentage of fine aggregate in total aggregate by absolute volume from table for the concrete using crushed coarse aggregate.

6. Adjust the values of water content and percentage of sand as provided in the table for any difference in workability, water cement ratio, grading of fine aggregate and for rounded aggregate the values are given in table. 7. Calculate the cement content form the water-cement ratio and the final water content as arrived after adjustment. Check the cement against the minimum cement content from the requirements of the durability, and greater of the two values is adopted. 8. From the quantities of water and cement per unit volume of concrete and the percentage of sand already determined in steps 6 and 7 above, calculate the content of coarse and fine aggregates per unit volume of concrete from the following relations:

where V = absolute volume of concrete = gross volume (1m3) minus the volume of entrapped air Sc = specific gravity of cement W = Mass of water per cubic metre of concrete, kg C = mass of cement per cubic metre of concrete, kg p = ratio of fine aggregate to total aggregate by absolute volume fa, Ca = total masses of fine and coarse aggregates, per cubic metre of concrete, respectively, kg, and Sfa, Sca = specific gravities of saturated surface dry fine and coarse aggregates, respectively 9. Determine the concrete mix proportions for the first trial mix. 10. Prepare the concrete using the calculated proportions and cast three cubes of 150 mm size and test them wet after 28-days moist curing and check for the strength. 11. Prepare trial mixes with suitable adjustments till the final mix proportions are arrived at.

M-20 CONCRETE MIX DESIGN

As per IS 10262-2009 & MORT&H A-1 Stipulations for Proportioning 1 Grade Designation M20 OPC 53 grade confirming to IS2 12269-1987 Type of Cement 3 Maximum Nominal Aggregate Size 20 mm Minimum Cement Content (MORT&H 4 1700-3 A) 250 kg/m3 Maximum Water Cement Ratio (MORT&H 5 0.5 1700-3 A) 6 Workability (MORT&H 1700-4) 25 mm (Slump) 7 Exposure Condition Normal 8 Degree of Supervision Good 9 Type of Aggregate Crushed Angular Aggregate Maximum Cement Content (MORT&H Cl. 10 540 kg/m3 1703.2) Superplasticiser Confirming to IS11 9103 Chemical Admixture Type A-2 Test Data for Materials 1 Cement Used Coromandal King OPC 53 grade 2 Sp. Gravity of Cement 3.15 3 Sp. Gravity of Water 1.00 4 Chemical Admixture Not Used 5 Sp. Gravity of 20 mm Aggregate 2.884 6 Sp. Gravity of 10 mm Aggregate 2.878 7 Sp. Gravity of Sand 2.605 8 Water Absorption of 20 mm Aggregate 0.97% 9 Water Absorption of 10 mm Aggregate 0.83% 10 Water Absorption of Sand 1.23% Free (Surface) Moisture of 20 mm 11 nil Aggregate Free (Surface) Moisture of 10 mm 12 nil Aggregate 13 Free (Surface) Moisture of Sand nil Sieve Analysis of Individual Coarse 14 Separate Analysis Done Aggregates Sieve Analysis of Combined Coarse 15 Aggregates Separate Analysis Done Sp. Gravity of Combined Coarse 15 Aggregates 2.882 16 Sieve Analysis of Fine Aggregates Separate Analysis Done A-3 Target Strength for Mix Proportioning 1 Target Mean Strength (MORT&H 1700-5) 30N/mm2

2 Characteristic Strength @ 28 days A-4 Selection of Water Cement Ratio Maximum Water Cement Ratio (MORT&H 1 1700-3 A) 2 Adopted Water Cement Ratio A-5 Selection of Water Content 1 Maximum Water content (10262-table-2) 2 Estimated Water content for 25 mm Slump 3 Superplasticiser used A-6 Calculation of Cement Content 1 Water Cement Ratio 2 Cement Content (145/0.5)

20N/mm2

0.5 0.5 186 Lit. 145 Lit. nil

0.5 290 kg/m3 Which is greater then 250 kg/m3 A-7 Proportion of Volume of Coarse Aggregate & Fine Aggregate Content 1 Vol. of C.A. as per table 3 of IS 10262 62.00% 2 Adopted Vol. of Coarse Aggregate 65.00% Adopted Vol. of Fine Aggregate ( 1-0.65) 35.00% A-8 Mix Calculations 1 Volume of Concrete in m3 1.00 3 2 Volume of Cement in m 0.09 (Mass of Cement) / (Sp. Gravity of Cement)x1000 3 Volume of Water in m3 0.145 (Mass of Water) / (Sp. Gravity of Water)x1000 4 Volume of Admixture @ 0% in m3 nil (Mass of Admixture)/(Sp. Gravity of Admixture)x1000 5 Volume of All in Aggregate in m3 0.763 Sr. no. 1 (Sr. no. 2+3+4) 6 Volume of Coarse Aggregate in m3 0.496 Sr. no. 5 x 0.65 7 Volume of Fine Aggregate in m3 0.267 Sr. no. 5 x 0.35 A-9 Mix Proportions for One Cum of Concrete (SSD Condition) 1 Mass of Cement in kg/m3 290 3 2 Mass of Water in kg/m 145 3 3 Mass of Fine Aggregate in kg/m 696 3 4 Mass of Coarse Aggregate in kg/m 1429 Mass of 20 mm in kg/m3 1029 3 Mass of 10 mm in kg/m 400 3 5 Mass of Admixture in kg/m nil

6 Water Cement Ratio

0.5

M-25 CONCRETE MIX DESIGN As per IS 10262-2009 & MORT&H A-1 Stipulations for Proportioning 1 Grade Designation M25 OPC 53 grade confirming to IS2 12269-1987 Type of Cement 3 Maximum Nominal Aggregate Size 20 mm Minimum Cement Content (MORT&H 4 1700-3 A) 310 kg/m3 Maximum Water Cement Ratio (MORT&H 5 1700-3 A) 0.45 6 Workability (MORT&H 1700-4) 50-75 mm (Slump) 7 Exposure Condition Normal 8 Degree of Supervision Good 9 Type of Aggregate Crushed Angular Aggregate Maximum Cement Content (MORT&H Cl. 10 540 kg/m3 1703.2) Superplasticiser Confirming to IS11 Chemical Admixture Type 9103 A-2 Test Data for Materials 1 Cement Used Coromandal King OPC 53 grade 2 Sp. Gravity of Cement 3.15 3 Sp. Gravity of Water 1.00 4 Chemical Admixture BASF Chemicals Company 5 Sp. Gravity of 20 mm Aggregate 2.884 6 Sp. Gravity of 10 mm Aggregate 2.878 7 Sp. Gravity of Sand 2.605 8 Water Absorption of 20 mm Aggregate 0.97% 9 Water Absorption of 10 mm Aggregate 0.83% 10 Water Absorption of Sand 1.23% Free (Surface) Moisture of 20 mm 11 Aggregate nil Free (Surface) Moisture of 10 mm 12 nil Aggregate 13 Free (Surface) Moisture of Sand nil Sieve Analysis of Individual Coarse 14 Separate Analysis Done Aggregates Sieve Analysis of Combined Coarse 15 Aggregates Separate Analysis Done 15 Sp. Gravity of Combined Coarse Aggregates 2.882

16 Sieve Analysis of Fine Aggregates A-3 Target Strength for Mix Proportioning 1 Target Mean Strength (MORT&H 1700-5) 2 Characteristic Strength @ 28 days A-4 Selection of Water Cement Ratio Maximum Water Cement Ratio (MORT&H 1 1700-3 A) 2 Adopted Water Cement Ratio A-5 Selection of Water Content 1 Maximum Water content (10262-table-2) Estimated Water content for 50-75 mm 2 Slump 3 Superplasticiser used A-6 Calculation of Cement Content 1 Water Cement Ratio 2 Cement Content (138/0.43)

Separate Analysis Done 36N/mm2 25N/mm2

0.45 0.43 186 Lit. 138 Lit. 0.5 % by wt. of cement

0.43 320 kg/m3 Which is greater then 310 kg/m3 A-7 Proportion of Volume of Coarse Aggregate & Fine Aggregate Content 1 Vol. of C.A. as per table 3 of IS 10262 62.00% 2 Adopted Vol. of Coarse Aggregate 62.00% Adopted Vol. of Fine Aggregate ( 1-0.62) 38.00% A-8 Mix Calculations 1 Volume of Concrete in m3 1.00 3 2 Volume of Cement in m 0.10 (Mass of Cement) / (Sp. Gravity of Cement)x1000 3 Volume of Water in m3 0.138 (Mass of Water) / (Sp. Gravity of Water)x1000 4 Volume of Admixture @ 0.5% in m3 0.00134 (Mass of Admixture)/(Sp. Gravity of Admixture)x1000 5 Volume of All in Aggregate in m3 0.759 Sr. no. 1 (Sr. no. 2+3+4) 6 Volume of Coarse Aggregate in m3 0.471 Sr. no. 5 x 0.62 7 Volume of Fine Aggregate in m3 0.288 Sr. no. 5 x 0.38 A-9 Mix Proportions for One Cum of Concrete (SSD Condition) 1 Mass of Cement in kg/m3 320 3 2 Mass of Water in kg/m 138 3 3 Mass of Fine Aggregate in kg/m 751

4 Mass of Coarse Aggregate in kg/m3 Mass of 20 mm in kg/m3 Mass of 10 mm in kg/m3 5 Mass of Admixture in kg/m3 6 Water Cement Ratio

1356 977 380 1.60 0.43

Concrete Mix Design M 20 Grade Of Concrete

Posted in Mix Design | Email This Post

1. REQUIREMENTS a) Specified minimum strength = 20 N/Sq mm b) Durability requirements i) Exposure Moderate ii) Minimum Cement Content = 300 Kgs/cum c) Cement (Refer Table No. 5 of IS:456-2000) i) Make Chetak (Birla) ii) Type OPC iii) Grade 43 d) Workability i) compacting factor = 0.7 e) Degree of quality control Good 2. TEST DATA FOR MATERIALS SUPPLIED a) CEMENT i) Specific gravity = 3.05 ii) Avg. comp. strength 7 days = 46.5 more than 33.0 OK 28 days = 55.0 more than 43.0 OK b) COARSE AGGREGATE i) 20mm Graded Type Crushed stone aggregate Specific gravity = 2.68 Water absorption = 1.46 Free (surface) moisture = 0

c) FINE AGGREGATE (Coarse sand) i) Type Natural (Ghaggar) Specific gravity = 2.6 Water absorption = 0.5 Free (surface) moisture = 1.4

3. TARGET MEAN STRENGTH (TMS) a) Statistical constant K = 1.65 b) Standard deviation S = 4.6 Thus, TMS = 27.59 N/Sqmm 4. SELECTION OF W/C RATIO a) As required for TMS = 0.5 b) As required for Moderate Exposure = 0.55 Assume W/c ratio of 0.5 5. DETERMINATION OF WATER & SAND CONTENT For W/C = 0.6 C.F. = 0.8 Max. Agg. Size of 20 mm a) Water content = 186 Kg/cum b) Sand as percentage of total aggregate by absolute volume = 35 %

Thus, Net water content = 180.42 Kg/cum Net sand percentage = 33 %

6. DETERMINATION OF CEMENT CONTENT W/c ratio = 0.5 Water content = 180.42 Kg/cum Thus, Cement content = 360.84 Kg/cum Adequate for moderate exposure Say 360 Kg/cum 7. DETERMINATION OF COARSE AND FINE AGGREGATE CONTENT Assume entrapped air as 2 % Thus, 0.98 cum = [180.42+360/3.05 + {1/0.33}*{fa/2.6}]/1000 & 0.98 cum = [180.42+360/3.05 + {1/0.67}*{Ca/2.68}]/1000 Hence, fa = 584 Kg/cum Ca = 1223.8 Kg/cum The final mix proportions of M-20 grade of concrete become:-

Note: 1 The above recommended mix design must be verified, by actual cube tests. 2 The mix design is based on the quality and grading of the materials actually supplied, by the client. Any variation in quality and gradation will result in changes in the mix design.