Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.

org/wiki/Standard_RAID_levels

Wikipedia is sustained by people like you. Please donate today.

Standard RAID levels

From Wikipedia , the free encyclopedia

The st andard RAID levels are a basic set of RAID configurations and employ striping,
mirroring, or parity. The standard RAID levels can be nested for other benefits (see Nested
RAID levels).

Contents
1 Concatenation (SPAN)
2 RAID 0
2.1 RAID 0 failure rate
2.2 RAID 0 performance
3 RAID 1
3.1 RAID 1 failure rate
3.2 RAID 1 performance
4 RAID 2
5 RAID 3
6 RAID 4
7 RAID 5
7.1 RAID 5 parity handling
7.2 RAID 5 disk failure rate
7.3 RAID 5 performance
7.4 RAID 5 usable siz e
8 RAID 6
8.1 RAID 6 performance
8.2 RAID 6 implementation
9 Non-standard RAID levels
10 JBOD
11 See also
12 References
13 External links

Concatenation (SPAN)
The controller treats each drive as a stand-alone disk, therefore each drive is an
independent logical drive. Concatenation does not provide data redundancy.

C oncat enat ion or Spanning of disks is not one of the numbered RAID levels, but it is a
popular method for combining multiple physical disk drives into a single virtual disk. It
provides no data redundancy. As the name implies, disks are merely concatenated
together, end to beginning, so they appear to be a single large disk.

Concatenation may be thought of as the reverse of partitioning. Whereas partitioning takes

1 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

one physical drive and creates two or more logical drives, concatenation uses two or more
physical drives to create one logical drive.

In that it consists of an array of independent disks, it can be thought of as a distant relative

of RAID. Concatenation is sometimes used to turn several odd-siz ed drives into one larger
useful drive, which cannot be done with RAID 0. For example, JBOD could combine 3 GB, 15
GB, 5.5 GB, and 12 GB drives into a logical drive at 35.5 GB, which is often more useful than
the individual drives separately.

In the diagram to the right, data are concatenated from the end of disk 0 (block A63) to the
beginning of disk 1 (block A64); end of disk 1 (block A91) to the beginning of disk 2 (block
A92). If RAID 0 were used, then disk 0 and disk 2 would be truncated to 28 blocks, the siz e of
the smallest disk in the array (disk 1) for a total siz e of 84 blocks.

Some RAID controllers use JBOD to refer to configuring drives without RAID features. Each
drive shows up separately in the OS. This JBOD is not the same as concatenation.

Many Linux distributions use the terms "linear mode" or "append mode". The Mac OS X 10.4
implementation — called a "Concatenated Disk Set" — does not leave the user with any
usable data on the remaining drives if one drive fails in a concatenated disk set, although
the disks otherwise operate as described above.

Concatenation is one of the uses of the Logical Volume Manager in Linux, which can be
used to create virtual drives spanning multiple physical drives and/or partitions.

RAID 0
A RAID 0 (also known as a st ripe set or st riped volume) splits
data evenly across two or more disks (striped) with no parity
information for redundancy. It is important to note that RAID 0 was
not one of the original RAID levels and provides z ero data
redundancy. RAID 0 is normally used to increase performance,
although it can also be used as a way to create a small number of
large virtual disks out of a large number of small physical ones.

A RAID 0 can be created with disks of differing siz es, but the
storage space added to the array by each disk is limited to the siz e
of the smallest disk. For example, if a 120 GB disk is striped
together with a 100 GB disk, the siz e of the array will be 200 GB.

Diagram of a RAID 0
setup.

In the diagram to the right, the odd blocks are written to disk 0 while the even blocks are
written to disk 1 such that A1, A2, A3, A4, … would be the order of blocks read if read
sequentially from the beginning.

RAID 0 f ailure rate

Although RAID 0 was not specified in the original RAID paper, an idealiz ed implementation

2 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

of RAID 0 would split I/O operations into equal-siz ed blocks and spread them evenly across
two disks. RAID 0 implementations with more than two disks are also possible, though the
group reliability decreases with member siz e.

Reliability of a given RAID 0 set is equal to the average reliability of each disk divided by the
number of disks in the set:

That is, reliability (as measured by mean time to failure (MTTF) or mean time between
failures (MTBF) is roughly inversely proportional to the number of members — so a set of
two disks is roughly half as reliable as a single disk. If there were a probability of 5% that
the disk would fail within three years, in a two disk array, that probability would be upped to
.

The reason for this is that the file system is distributed across all disks. When a drive fails
the file system cannot cope with such a large loss of data and coherency since the data is
"striped" across all drives (the data cannot be recovered without the missing disk). Data can
be recovered using special tools (see data recovery), however, this data will be incomplete
and most likely corrupt, and recovery of drive data is very costly and not guaranteed.

RAID 0 perf ormance

While the block siz e can technically be as small as a byte, it is almost always a multiple of
the hard disk sector siz e of 512 bytes. This lets each drive seek independently when
randomly reading or writing data on the disk. How much the drives act independently
depends on the access pattern from the file system level. For reads and writes that are
larger than the stripe siz e, such as copying files or video playback, the disks will be seeking
to the same position on each disk, so the seek time of the array will be the same as that of
a single drive. For reads and writes that are smaller than the stripe siz e, such as database
access, the drives will be able to seek independently. If the sectors accessed are spread
evenly between the two drives, the apparent seek time of the array will be half that of a
single drive (assuming the disks in the array have identical access time characteristics). The
transfer speed of the array will be the transfer speed of all the disks added together, limited
only by the speed of the RAID controller. Note that these performance scenarios are in the
best case with optimal access patterns.

RAID 0 is useful for setups such as large read-only NFS servers where mounting many disks
is time-consuming or impossible and redundancy is irrelevant.

RAID 0 is also used in some gaming systems where performance is desired and data
integrity is not very important. However, real-world tests with games have shown that
RAID-0 performance gains are minimal, although some desktop applications will benefit.
[1][2]
Another article examined these claims and concludes that "Striping does not always
increase performance (in certain situations it will actually be slower than a non-RAID setup),
[3]
but in most situations it will yield a significant improvement in performance."

RAID 1

3 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

A RAID 1 creates an exact copy (or mirror) of a set of data on two

or more disks. This is useful when read performance or reliability
are more important than data storage capacity. Such an array can
only be as big as the smallest member disk. A classic RAID 1
mirrored pair contains two disks (see diagram), which increases
reliability geometrically over a single disk. Since each member
contains a complete copy of the data, and can be addressed
independently, ordinary wear-and-tear reliability is raised by the
power of the number of self-contained copies.

RAID 1 f ailure rate

For trivial example, consider a RAID 1 with 2 identical models of a

disk drive with a 5% probability that the disk would fail within three
years. Provided that the failures are statistically independent, then
Diagram of a RAID 1
the probability of both drives failing (with no replacements for 3
setup.
years) is

RAID 1 perf ormance

Additionally, since all the data exists in two or more copies, each with its own hardware, the
read performance can go up roughly as a linear multiple of the number of copies. That is, a
RAID 1 array of two drives can be reading in two different places at the same time, though
[4]
not all implementations of RAID 1 do this. To maximiz e performance benefits of RAID 1,
independent disk controllers are recommended, one for each disk. Some refer to this
practice as split t ing or duplexing. When reading, both disks can be accessed
independently and requested sectors can be split evenly between the disks. For the usual
mirror of two disks, this would, in theory, double the transfer rate when reading. The
apparent access time of the array would be half that of a single drive. Unlike RAID 0, this
would be for all access patterns, as all the data are present on all the disks. In reality, the
need to move the drive heads to the next block (to skip unread blocks) can effectively
mitigate speed advantages for sequential access. Read performance can be further
improved by adding drives to the mirror. Many older IDE RAID 1 controllers read only from
one disk in the pair, so their read performance is always that of a single disk. Some older
RAID 1 implementations would also read both disks simultaneously and compare the data
to detect errors. The error detection and correction on modern disks makes this less useful
in environments requiring normal availability. When writing, the array performs like a single
disk, as all mirrors must be written with the data. Note that these performance scenarios
are in the best case with optimal access patterns.

RAID 1 has many administrative advantages. For instance, in some environments, it is

possible to "split the mirror": declare one disk as inactive, do a backup of that disk, and then
"rebuild" the mirror. This is useful in situations where the file system must be constantly
available. This requires that the application supports recovery from the image of data on
the disk at the point of the mirror split. This procedure is less critical in the presence of the
"snapshot" feature of some file systems, in which some space is reserved for changes,
presenting a static point-in-time view of the file system. Alternatively, a new disk can be
substituted so that the inactive disk can be kept in much the same way as traditional
backup. To keep redundancy during the backup process, some controllers support adding a

4 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

third disk to an active pair. After a rebuild to the third disk completes, it is made inactive and
backed up as described above.

RAID 2
A RAID 2 stripes data at the bit (rather than block) level, and uses a Hamming code for error
correction. The disks are synchroniz ed by the controller to spin in perfect tandem.
Extremely high data transfer rates are possible. This is the only original level of RAID that is
not currently used.

The use of the Hamming(7,4) code (four data bits plus three parity bits) also permits using 7
disks in RAID 2, with 4 being used for data storage and 3 being used for error correction.

RAID 2 is the only standard RAID level, other than some implementations of RAID-6, which
can automatically recover accurate data from single-bit corruption in data. Other RAID levels
can detect single-bit corruption in data, or can sometimes reconstruct missing data, but
cannot reliably resolve contradictions between parity bits and data bits without human
intervention.

(Multiple-bit corruption is possible though extremely rare. RAID 2 can detect but not repair
double-bit corruption.)

At the present time, there are no commercial implementations of RAID-2.

RAID 3
A RAID 3 uses byte-level striping with a
dedicated parity disk. RAID 3 is very rare in
practice. One of the side-effects of RAID 3 is
that it generally cannot service multiple
requests simultaneously. This comes about
because any single block of data will, by
definition, be spread across all members of
the set and will reside in the same location.
So, any I/O operation requires activity on every
disk and usually requires synchroniz ed
spindles.

In our example, a request for block "A"

consisting of bytes A1-A6 would require all
three data disks to seek to the beginning (A1) Diagram of a RAID 3 setup of 6-byte blocks and
and reply with their contents. A simultaneous two parity bytes, shown are two blocks of data
request for block B would have to wait. (orange and green)

RAID 4

5 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

A RAID 4 uses block-level striping with a

dedicated parity disk. This allows each
member of the set to act independently when
only a single block is requested. If the disk
controller allows it, a RAID 4 set can service
multiple read requests simultaneously. RAID 4
looks similar to RAID 5 except that it does not
use distributed parity, and similar to RAID 3
except that it stripes at the block level, rather
than the byte level. Generally, RAID 4 is
implemented with hardware support for parity
calculations, and a minimum of 3 disks is
required for a complete RAID 4 configuration.

In the example on the right, a read request for Diagram of a RAID 4 setup with dedicated parity
block "A1" would be serviced by disk 0. A disk with each color representing the group of
simultaneous read request for block B1 would blocks in the respective parity block (a stripe)
have to wait, but a read request for B2 could
be serviced concurrently by disk 1.

RAID 5
A RAID 5 uses block-level striping with parity
data distributed across all member disks. RAID
5 has achieved popularity due to its low cost
of redundancy. This can be seen by comparing
the number of drives needed to achieve a
given capacity. RAID 1 or RAID 0+1, which yield
redundancy, give only s/2 storage capacity,
where s is the sum of the capacities of n
drives used. In RAID 5, the yield is s * (n - 1)/n.
Using 1 TB drives as an example, four of them
can build a 2 TB redundant array under RAID 1
or RAID 1+0, but they can be used to build a 3
TB array under RAID 5. Although RAID 5 is
commonly implemented in a disk controller,
some with hardware support for parity Diagram of a RAID 5 setup with distributed
calculations (hardware raid cards) and some parity with each color representing the group of
using the main system processor blocks in the respective parity block (a stripe).
(motherboard based raid controllers), it can This diagram shows left asymmetric algorithm
also be done at the operating system level,
e.g. using Windows "Dynamic Disks" or with
mdadm in Linux. A minimum of 3 disks is required for a complete RAID 5 configuration. In
some implementations a degraded RAID 5 disk set can be made (3 disk set of which only 2
are online), while mdadm supports a fully-functional (non-degraded) RAID 5 setup with two
disks - which function as a slow RAID-1, but can be expanded with further volumes.

In the example on the right, a read request for block "A1" would be serviced by disk 0. A
simultaneous read request for block B1 would have to wait, but a read request for B2 could
be serviced concurrently by disk 1.

6 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

RAID 5 parity handling

A concurrent series of blocks (one on each of the disks in an array) is collectively called a
"stripe". If another block, or some portion of a block, is written on that same stripe, the
parity block (or some portion of the parity block) is recalculated and rewritten. For small
writes, this requires:

Reading the old data block

Reading the old parity block
Comparing the old data block with the write request. For each bit that has flipped
(changed from 0 to 1, or from 1 to 0) in the data block, flipping the corresponding bit in
the parity block
Writing the new data block
Writing the new parity block

The disk used for the parity block is staggered from one stripe to the next, hence the term
"distributed parity blocks". RAID 5 writes are expensive in terms of disk operations and
traffic between the disks and the controller.

The parity blocks are not read on data reads, since this would be unnecessary overhead
and would diminish performance. The parity blocks are read, however, when a read of
blocks in the stripe and within the parity block in the stripe are used to reconstruct the
errant sector. The CRC error is thus hidden from the main computer. Likewise, should a disk
fail in the array, the parity blocks from the surviving disks are combined mathematically
with the data blocks from the surviving disks to reconstruct the data on the failed drive "on
the fly".

This is sometimes called Interim Data Recovery Mode. The computer knows that a disk drive
has failed, but this is only so that the operating system can notify the administrator that a
drive needs replacement; applications running on the computer are unaware of the failure.
Reading and writing to the drive array continues seamlessly, though with some
performance degradation. The difference between RAID 4 and RAID 5 is that in interim data
recovery mode, RAID 5 might be slightly faster than RAID 4: When the CRC and parity are in
the disk that failed, the calculation does not have to be performed, while with RAID 4, if one
of the data disks fails, the calculations have to be performed with each access.

RAID 5 disk f ailure rate

The maximum number of drives in a RAID 5 redundancy group is theoretically unlimited, but
it is common practice to limit the number of drives. The tradeoffs of larger redundancy
groups are greater probability of a simultaneous double disk failure, the increased time to
rebuild a redundancy group, and the greater probability of encountering an unrecoverable
sector during RAID reconstruction. As the number of disks in a RAID 5 group increases, the
Mean Time Between Failures (MTBF, the reciprocal of the failure rate) can become lower
than that of a single disk. This happens when the likelihood of a second disk failing out of
(N-1) dependent disks, within the time it takes to detect, replace and recreate a first failed
disk, becomes larger than the likelihood of a single disk failing. RAID 6 is an alternative that
provides dual parity protection thus enabling larger numbers of disks per RAID group. Some
implementations have a hot spare disk that can be used to immediately rebuild the failed
drive.

Some RAID vendors will avoid placing disks from the same manufacturing lot in a

7 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

redundancy group to minimiz e the odds of simultaneous early life and end of life failures as
evidenced by the Bathtub curve.

RAID 5 perf ormance

RAID 5 implementations suffer from poor performance when faced with a workload which
includes many writes which are smaller than the capacity of a single stripe; this is because
parity must be updated on each write, requiring read-modify-write sequences for both the
data block and the parity block. More complex implementations may include non-volatile
write back cache to reduce the performance impact of incremental parity updates.

Random write performance is poor, especially at high concurrency levels common in large
multi-user databases. The read-modify-write cycle requirement of RAID 5's parity
implementation penaliz es random writes by as much as an order of magnitude compared
[5]
to RAID 0.

Performance problems can be so severe that some database experts have formed a group
[6]
called BAARF — the Battle Against Any Raid Five.

The read performance of RAID 5 is almost as good as RAID 0 for the same number of disks.
Except for the parity blocks, the distribution of data over the drives follows the same pattern
as RAID 0. The reason RAID 5 is slightly slower is that the disks must skip over the parity
blocks.

In the event of a system failure while there are active writes, the parity of a stripe may
become inconsistent with the data. If this is not detected and repaired before a disk or block
fails, data loss may ensue as incorrect parity will be used to reconstruct the missing block in
that stripe. This potential vulnerability is sometimes known as the "write hole". Battery-
backed cache and similar techniques are commonly used to reduce the window of
opportunity for this to occur.

RAID 5 usable size

Parity data use up the capacity of one drive in the array (this can be seen by comparing it
with RAID 4: RAID 5 distributes the parity data across the disks, while RAID 4 centraliz es it on
one disk, but the amount of parity data is the same). In case that the drives vary in capacity,
the smallest of them sets the bar. Therefore, the usable capacity of a RAID 5 array is
, where N is the total number of drives in the array and S min is the capacity
of the smallest drive in the array..

The number of hard drives that can belong to a single array is theoretically unlimited. The
time required for initial construction of the array as well as that for reconstruction of a failed
disk increases with the number of drives in an array.

RAID 6

8 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

RAID 6 extends RAID 5 by adding an

additional parity block, thus it uses block-level
striping with two parity blocks distributed
across all member disks. It was not one of the
original RAID levels.

RAID 5 can be seen as a special case of a

[7]
Reed-Solomon code. RAID 5, being a
degenerate case, requires only addition in the
Galois field. Since we are operating on bits,
the field used is a binary galois field GF(2). In
cyclic representations of binary galois fields, Diagram of a RAID 6 setup, which is identical to
addition is computed by a simple XOR. RAID 5 other than the addition of a second
parity block
After understanding RAID 5 as a special case
of a Reed-Solomon code, it is easy to see that
it is possible to extend the approach to produce redundancy simply by producing another
8
syndrome; typically a polynomial in GF(2 ) (8 means we are operating on bytes). By adding
additional syndromes it is possible to achieve any number of redundant disks, and recover
from the failure of that many drives anywhere in the array, but RAID 6 refers to the specific
case of two syndromes.

Like RAID 5, the parity is distributed in stripes, with the parity blocks in a different place in
each stripe.

RAID 6 perf ormance

RAID 6 is no more space inefficient than RAID 5 with a hot spare drive when used with a
small number of drives, but as arrays become bigger and have more drives the loss in
storage capacity becomes less important and the probability of data loss is greater. RAID 6
provides protection against data loss during an array rebuild; when a second drive is lost, a
bad block read is encountered, and the more often occurrence of removal and replacement
of the wrong disk drive.

The usable capacity of a RAID 6 array is , where N is the total number of

drives in the array and S min is the capacity of the smallest drive in the array.

RAID 6 does not have a performance penalty for read operations, but it does have a
performance penalty on write operations due to the overhead associated with parity
calculations. Performance varies greatly depending on how RAID 6 is implemented in the
manufacturer's storage architecture - in software, firmware or by using firmware and
specializ ed ASICs for intensive parity calculations. It can be as fast as RAID 5 with one fewer
drives (same number of data drives.)

RAID 6 implementation

According to SNIA (Storage Networking Industry Association), the definition of RAID 6 is: "Any
form of RAID that can continue to execute read and write requests to all of a RAID array’s
virtual disks in the presence of any two concurrent disk failures. Several methods, including
dual check data computations (parity and Reed Solomon), orthogonal dual parity check
[8]
data and diagonal parity have been used to implement RAID Level 6."

9 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

Non-standard RAID levels

There are other RAID levels that are promoted by individual vendors, but not generally
standardiz ed. The non-standard RAID levels 5E, 5EE and 6E extend RAID 5 and 6 with
hot-spare drives.

Other non-standard RAID levels include: RAID 1.5, RAID 7, RAID-DP, RAID S or Parity RAID,
Matrix RAID, RAID-K, RAID-Z, RAIDn, Linux MD RAID 10, IBM ServeRAID 1E, and unRAID.

JBOD
JBOD stands for Just a Bunch Of Disks (Just a Box Of Drives). Depending on the Host Bus
Adapter a JBOD can be used as individual disks or any RAID configuration supported by the
HBA.

See also
RAID
Nested RAID levels
Non-standard RAID levels

References
1. ^ "Western Digital's Raptors in RAID-0 : Are two drives better than one? (http://www.anandtech.com
/storage/showdoc.aspx? i=210 1) ". AnandTech (July 1, 20 0 4). Retrieved on 20 0 7-11-24.
2. ^ "Hitachi Deskstar 7K10 0 0 : Two Terabyte RAID Redux (http://www.anandtech.com/storage
/showdoc.aspx? i=29 74) ". AnandTech (April 23, 20 0 7). Retrieved on 20 0 7-11-24.
3. ^ "RAID 0 : Hype or blessing? (http://tweakers.net/reviews/515/1/raid-0 -hype-or-blessing-pagina-
1.html) ". Tweakers.net (August 7, 20 0 4). Retrieved on 20 0 8 -0 7-23.
4. ^ "Mac OS X, Mac OS X Server: How to Use Apple-Supplied RAID Software (http://docs.info.apple.com
/article.html? artnum=10 6 59 4) ". Apple.com. Retrieved on 20 0 7-11-24.
5. ^ Cary Millsap (21 August 19 9 6 ). "Configuring Oracle Server for VLDB (http://oreilly.com/catalog
/oressentials2/chapter/vldb1.pdf) " (PDF).
6 . ^ "BAARF - Battle Against Any Raid Five (http://www.baarf.com) ". Retrieved on 20 0 8 -0 7-11.
7. ^ H. Peter Anvin (24 October 20 0 7). "The mathematics of RAID-6 (http://kernel.org/pub/linux/kernel
/people/hpa/raid6.pdf) " (PDF).
8 . ^ "Dictionary R (http://www.snia.org/education/dictionary/r/) ". Storage Networking Industry
Association. Retrieved on 20 0 7-11-24.

External links
Tutorial on "RAID 6 Essentials — reduced performace or not?"
(http://www.brainshark.com/winchestersystemsinc1/vu?pi=707421860)
IBM summary on RAID levels (http://www-1.ibm.com/support
/docview.wss?uid=swg21149421)
RAID 5 Parity explanation and checking tool. (http://www.dtidata.com/resourcecenter
/2008/05/08/raid-configuration-parity-check/)
Dell animations and details on RAID levels 0, 1, 5 (http://support.dell.com/support
/topics/global.aspx/support/entvideos/raid?c=us&l=en&s=gen)

10 of 11 10/08/2008 04:01 PM
Standard RAID levels - Wikipedia, the free encycl... http://en.wikipedia.org/wiki/Standard_RAID_levels

Retrieved from "http://en.wikipedia.org/wiki/Standard_RAID_levels"

Categories: RAID
Hidden categories: All articles with unsourced statements • Articles with unsourced
statements since February 2008 • Articles with unsourced statements since September
2008 • Articles needing additional references from February 2008

This page was last modified on 8 October 2008, at 18:46.

All text is available under the terms of the GNU Free Documentation License. (See
C opyright s for details.)
Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a U.S.
registered 501(c)(3) tax-deductible nonprofit charity.

11 of 11 10/08/2008 04:01 PM