Service Manual

ViewSonic M2
Model No. VS17808
DLP Projector

(M2_SM Rev. 1f Jun. 2021)

ViewSonic® 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
 Copyright
Copyright© 2021 by ViewSonic Corporation. All rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language
or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.

Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further,
ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents
hereof without obligation of ViewSonic to notify any person of such revision or changes.

Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.

Revision History
Revision SM Editing Date ECR Number Description of Changes Editor

1a 03/30/20 Initial Release. (PE: CK Chen) Sophia Kao

1b 07/21/20 Update contents. Sophia Kao
1c 01/28/21 Update contents. Sophia Kao
1d 03/31/21 Add "Force FW update". Sophia Kao
1e 06/08/21 Update RSPL. Sophia Kao
1f 06/25/21 Update contents. Sophia Kao

ViewSonic Corporation 1 Confidential - Do Not Copy M2

 INDEX

1. Product General Requirement.................................................................................................. 4

2. Block Diagram ................................................................................................................................. 9
3. Disassemble and assemble parts........................................................................................... 10
4. Software upgrade.......................................................................................................................... 28
5. Factory mode ................................................................................................................................. 39
6. Firmware upgrade ....................................................................................................................... 42
7. Panel function description ....................................................................................................... 44
8. Exploded View and Recommend Spare parts List.............................................................. 45
9. Troubleshooting Guide.............................................................................................................. 48

ViewSonic Corporation 2 Confidential - Do Not Copy M2

 Product Specifications
The Projector consists of the DLP projector controller, Lamp controller, Power supply system, and the
system cooling controller. The DLP controller captures the digital PC data and video data and converts
them into the DMD display device. The lamp controller controls the lamp’s power and synchronizes its
frequency with color display sequence. Power supply unit controls the AC line power factor and converts
primary voltage to secondary low voltage for digital board. The system cooling controller drives the
airflow to cool the lamp’s heat and electrical component’s heat.

ViewSonic Corporation 3 Confidential - Do Not Copy M2

 1 Product General Requirement

1.1 ProductInformation(ViewSonic Provide)

Product Name ViewSonicM2

Model Number VS17808

SN Prefix Number VT9

UPC number 76690700308 6

GTIN code 0076690700308 6
EDID 385D

1.2 Production Accessories

VSA: US,
VSE : European (Schuko), UK VSE x2,
Power Cable (1m) VSCN: China Others
VSI: by PI instrcution x1
By regions SKU
Signal Cable USB Type C cable (USB-IF verify, 1m) x1

Remote Control With batteries X1

Lens Cover N/A

Carry bag N/A X1

Cable Management cover N/A

Wall/ceiling mount N/A

Interactive module N/A

QSG Color A3 x1

Carton Color x1

Double Packing Black printing x1

Air filter N/A

Warranty card / sticker For VSCN and JP SKU only x1

ViewSonic style OSD(22 languages)(English, French,
Spanish, Thai, Korean, German, Italian, Russian,
OSD Style/ language Swedish, Dutch, Polish, Czech, T-Chinese, S-Chinese,
Japanese, Turkish, Portuguese, Finnish, Indonesian,
India, Arabic, Vietnamese)
E-File
English, S-Chinese, T-Chinese,
User’s manual language Finnish,French,German,Italian,Japanese,Korean,Poli
sh,Portuguese,Russian,Spanish,Swedish,Turkish) –
15 Languages

ViewSonic Corporation 4 Confidential - Do Not Copy M2

 1.3 DMDinformation
TI.33DMD0.33" 1080p S3151920x1080
DMD Type
3437+FPGA
Dark Chip version N/A

Package Type P13HA_MF

Size 0.33

Native Pixel (DMD) 1368(H) x 768(V)

Display Pixels (Native for user) 1920(H) x 1080(V)

Display Pixels (Actuator) 1920(H) x 1080(V)

Color Depth 30 Bits (1.07 Billion Colors)

Driver Type DD3437

Scalar Mstar 6A838

Panel Pixel Quality Follow TI spec. (Refer to Appendix 4.1 )

Image Imperfection Follow TI spec. (Refer to Appendix4.1 )

1.4 Projection Optical Engine Data

Zoom Factor Fixed

Zoom ratio Fixed

True Zoom N/A

Focus AF

Focus range(Clearly) 0.5~3m / 56.5”~169.5”

Focus range(Visible) 50” ~210”

Lens Shift Range N/A

Throw Ratio 1.23

Optical Offset (Half height) 100%+-3%

F# 1.7

Focal Length 9.251mm

Color Wheel N/A

Color Wheel speed N/A

Color Wheel Dust proof N/A

Color wheel index N/A

ViewSonic Corporation 5 Confidential - Do Not Copy M2

 1.5 Projection Optical specification
DC in:
Normal:476lm(typ)
Normal: 400lm(min)
Eco:333lm(typ)
Eco:280lm(min)
ANSI Lumen USB-C:
Normal:285lm(typ)
Normal: 240lm(min)
Eco:133lm(typ)
Eco:112lm(min)
 Brightest mode@full white 100IRE
<30%
ANSI uniformity
>-30%
JBMA Uniformity ≥83%

ANSI Contrast 130:1

452: 1 (Typ)
FOFO ContrastRatio (Native)
200:1 (min)
3,000,000:1
When RGB value of content input is smaller
FOFO Contrast Ratio (DCR) than 20%, system will automatically switch to Eco
mode, if RGB value is greater than 60%, the
projector will back to Normal mode.
Flare R<=3.5; G<=3.5; B<=3.5 pixels

Defocus R<=2.5; G<=2.5; B<=2.5 pixels

Focus shall be visibly clear, crisp, and sharp over the
entire surface of the image after adjustment, based
on the following test conditions and method:

Test condition ： Image size 60in, Contrast and

Brightness at default setting.

Test method ： Optimize focus balance using a

Focus
pattern of white letter “E” (HxW = 5x3 pixels, with 1
pixel gap) on black background.

Criteria：Every letter E should be resolved in whole

area of the image.

When doubt takes place at image size 300”, it is
judged by conference between ViewSonic and
supplier.
Color x y
White 0.313±0.003 0.329±0.003
Color Coordinate (Movie mode@70IRE)
Red 0.640±0.003 0.330±0.003
Green 0.300±0.003 0.600±0.003

ViewSonic Corporation 6 Confidential - Do Not Copy M2

 Blue 0.150±0.003 0.060±0.003
∆x = +/- 0.004, ∆y = +/- 0.004
Chromaticity Uniformity (Brightest mode@100IRE)
∆x = +/- 0.004, ∆y = +/- 0.004
Measurement Device Minolta CL-200 or T10 equivalent device with
accredited traceability

1.6 Screen Defect

DMD Refer to 4.1 DMD spec

Scratches There shall be no scratches on the mirror surfaces,

prism surfaces, lens surfaces, or DMD surfaces that
cause visible artifacts on the screen image. (refer
Light leakage spec. and DMD Image Quality SPEC )
Artifacts There shall be no objectionable vertical streaking
artifacts visible at low brightness levels. The screen
at this condition must be uniform free of noise
disturbances.
(refer DMD Image Quality SPEC for DMD defect)
Blemishes There shall be no blemishes on the mirror surfaces,
prism surfaces, lens surfaces, or DMD surfaces that
cause visible artifacts with TI Gray10 image. (refer
DMD Image Quality SPEC for DMD defect)
Lint and Dust There shall be no visible artifacts in the image due
to lint on mirror surfaces, prism surfaces, lens
surfaces, or DMD surfaces when the image is
focused. (refer DMD Image Quality SPEC)
Light leakage in active area <0.5 lux. with 60” diagonal screen size
Note: This light leakage in active area is only
described as the spot light with obvious shape.
It is not included the uniformity difference of the
projector for black pattern. (otherwise refer DMD
Image Quality SPEC for DMD defect)
Light leakage out of active area <0.5 lux. with 60”~80” diagonal screen size
(otherwise refer DMD Image Quality SPEC for
DMD defect)

IMAGE DISTORTION H1
Keystone = (W2-W1)/ (W1+W2) x 100% < 1%
Vertical TV dist = (H1+H2-2xH3)/2H2 x100% < 1%
Horizontal TV dist = (W1+W2-2xW3)/2W1 x100% <
1%
Optical Distortion W1: image width at image bottom
W2: image width at image top
W3: image width at the half image height.
H1: image height at image left
H2: image height at image right
H3: image height at half image

ViewSonic Corporation 7 Confidential - Do Not Copy M2

 Note:
1. Keystone and Vertical TV Distortion are
recommended for Front Projection Display
2. Vertical and Horizontal TV Distortion are
recommended for Rear Projection Display

Measurement Device Minolta CL-200 or T10 equivalent device with

accredited traceability

1.7 Stray light Artifacts

Black Image There shall be no visible stray light in the display
area. (When doubt takes place, it is judged by
conference between ViewSonic and supplier).(refer
Light Leakage spec.)

1.8 Raster Artifacts

Video Artifacts No Visible Streaking, Sag, or Smearing Artifacts
when driven by the specified video cards in the
primary mode and after user adjustment to best
condition
Power Supply, and Grounding Artifacts No visible artifacts in any specified video mode within the
horizontal or vertical frequency range of the monitor. (When
doubt takes place, it is judged by conference between
ViewSonic and supplier).

ViewSonic Corporation 8 Confidential - Do Not Copy M2

 Block Diagram

ViewSonic Corporation 9 Confidential - Do Not Copy M2

 Disassemble and assemble parts
The disassemble SOP
一、Remove the bottom covercomponents（R54-M2B03-PA-ZJ）
1、Remove the three rubberpads(R54-M2001-TPU)A, B and C by rotating counterclockwise, as shown in
figure 1.1
2、Remove thefive bottom cover screws (R56-B2045-AB1) with a screwdriver,as shown in figure 1.2
3、Press the cover of WIFI module(R54-M2B04-PA) down with thumb and then remove it, as shown in
figure 1.2
4、Put your index finger into the gap of the WIFI module slot and lift it up forcefully to separate the
bottom cover(R54-M2B03-PA), as shown in figure 1.3

Tapping screw*5
Rubberpad R56-B2045-AB1
R54-M2001-TPU Putyour index
finger in and lift
The wifi module
it up
cover is pushed
down

figure 1.1
figure 1.2 figure 1.3

二、Disassemble IO board components（R41-M2002-MA01S-ZJ）

1、Pull the wires on the IO board from their respective connectors and remove the fan from the
grounding conductive cloth(R71-010935-002) of the optical engine, as shown in figure2.1
2、Remove the six screws from the IO board with a screwdriver, as shown in figure2.2，Note that 1-4 are
tapping screws(R56-B2045-AB1）, 5 and 6 are interface copper pillars screw(R57-B2860-12) flat head
machine teeth

2
Pull out the wire
1

screw*6
Conductive cloth

Note that this connector

requires the black lock to
3 5 6
be turned up before the
4
FPC is unplugged

figure 2.1 figure2.2

ViewSonic Corporation 10 Confidential - Do Not Copy M2

 三、Disassemble the fan（R30-M29027-210）
1、Remove the fan seal acetate cloth with a tweezer(R71-M2012-01)
2、Remove the three tapping screws from the fan with a screwdriver(R56-B2045-AB1)
3、Remove the fan from the main board connector and remove the fan

Tapping
screw*3

the fan seal

acetate cloth

四、Disassemble the fan fixedholdercomponents(R54-M2B09-PA-ZJ)

1、Pull theoptical engine light wires from the connector on the main board and pull it out with other
wires from the line slot of the fan holder, as shown in figure 4.1
2、Use a screwdriver to remove the five tapping screws (R56-B2045-AB1)from the fan holder, remove the
speaker wire from the main board connector, and remove the the fan fixedholdercomponents, as shown
in figure 4.2
the fan fixedholdercomponentsthe
Fourgroups of optical (component contains spongeattached
engine light wires to it)

line slot

speaker wire
seat

figure 4.1 figure 4.2

五、Disassemble cavity speaker（R29-852704-04A）

1、Use tweezers to remove the air duct rigid sponge (R74-M2008-14)
2、Use a screwdriver to remove the three speaker screws(R56-B6080-AB1), and carefully extract the
speaker by hand, taking care not to touch the lower and side diaphragm

ViewSonic Corporation 11 Confidential - Do Not Copy M2

 the air duct rigid
sponge
Speaker screw*3

六、Disassemble the optical engine components（R32-DLP02-AH01-ZJ）

1、Pull out the wire of the vibrating mirror FPC(R36-M2009-05-ZJ) from the connector on the main board,
take out the fan and the grounding conductive cloth(R71-010935-002) of the optical engine FPC, and
separate the optical engine FPC connector from the main board
2、Remove the seven tapping screws (R56-B2045-AB1) on the optical engine and heat sink with a
screwdriver, take the heat sink fins by hand and remove the optical engine components.
Note that the graphic text describes the notes.

Fan and opticalengine FPC

grounding conductive cloth

Tapping screws*7 Turn up the

R56-B2045-AB1 black lock on the Remove all the screws and
connector and connectors, conductive cloth,
then pull outthe etc., and hold the heat sink
vibrating mirror fins by hand to extract the
wire optical engine components

ViewSonic Corporation 12 Confidential - Do Not Copy M2

 七、Disassemble optical engine wire
Optical engine R light wirecomponentR35-M2001-02U-ZJThe color is red around the magnetic ring
Optical engineG light wirecomponentR35-M2002-05U-ZJThe color is green around the magnetic ring
Optical engineBlightwirecomponentR35-M2003-06U-ZJThe color is blue around the magnetic ring
Optical engine PB light wirecomponentR35-M2004-00U-ZJThe color is black around the magnetic ring
the wire of the vibrating mirrorFPCR36-M2009-05-ZJ 4pin FPC Cover with black conductive cloth
The light coupling wireR35-M2005-00U 4PIN Black circular wire
Remove R/G/B/PB light wire, the vibrating mirror wire and the light coupling wire from the
corresponding connector in turn

Pull out the light

coupling wire

Pull out the optical

engine R\G\B\PB light

Turn up the black

lock and pull out
thevibrating mirror
wire

ViewSonic Corporation 13 Confidential - Do Not Copy M2

 八、Disassemble optical engine and heat sink

Use the screwdriver to remove 6 screws(R57-B2860-11)which fixing theoptical engine and heat sink,
separating the optical engine and heat sink

Use the screwdriver

to remove 6 screws

九 、 Disassemble interface sheet metal parts( R59-M2A02-K40) and interface copper

pillars(R59-M2A03-B00) from main board
Remove the two tapping screws( R56-B2045-AB1) of the locking interface sheet metal parts,put the
inner hexagon copper cover on the interface copper pillars, rotate counterclockwise, and screw down
the two interface copper pillars

tapping screws *2

Interface sheet metal parts interface copper pillars

ViewSonic Corporation 14 Confidential - Do Not Copy M2

 十、Disassemble the main board(M2_REF_VER_V05) from the topcover
1、Remove the main board _IO board FPC flat cable(R35-M2010-05) from the main board connector, pay
attention to the black lock on the corresponding connector on the main board should be turned up first,
then pull out. Do not pull out directly.
2 、 Remove the p-senser_ir wire (R35-M2006-00U) and the focus board _ main board
wire(r35-m2008-01u) from the main board connector
3、Remove four tapping screws (R56-B2045-AB1) from the main board with a screwdriver. Take out the
main board.

main board _IO board

FPC flat cable

tapping screw*4
P-senser_ir wire, focusing
board _ main board wire
corresponds to main board
connector

十一、Disassemble IR boardcomponents(R41-M2003-MA01S-ZJ)
1、Remove the p-senser_ir wire from the topcover line slot and pull it out on the connector on the IR
board
2、Remove two IR board screws (R56-B4020-BF1) from the IR board
3、Remove the P_senser soft rubber sleeve from the IR board
P_senser soft
IR board screws *2 rubber sleeve

ViewSonic Corporation 15 Confidential - Do Not Copy M2

 十二、Disassemble the focus board components(R41-M2004-MA01-ZJ)
1、Remove the focus board _IO board wire(R35-M2007-00U) and the focus board _ main board
wire(R35-M2008-01U) from the top cover line slot
2、Remove two focus board screws (R56-B2045-AB2) with a screwdriver and carefully remove the focus
board by holding the edge of the focus board
3、Pull the two wires from the focusing board alignment connector

focus board screw

line slot

The assembly SOP

一、Fixed IR boardcomponents(R41-M2003-MA01S-ZJ)
1、Apply the P_senser soft rubber sleeve (R54-M2003-TPU) to the senser of IR board, note that the
protruding end of the rubber sleeve is opposite to the concave side of IR board
2、Insert the p-senser_ir wire (R35-M2006-00U) into the IR board connector. Be careful not to insert the
connector needle aslant
3、Insert the IR board into the corresponding position of the top cover from bottom to top. Two screw
holes of the IR board shall be aligned with the screw pillars of the top cover, and two IR board screws
shall be locked (R56-B4020-BF1).

P_senser soft
rubber sleeve
protruding end
P-senser_IR
wire

IR board
screw

ViewSonic Corporation 16 Confidential - Do Not Copy M2

 二、Fixed focus board components (R41-M2004-MA01-ZJ)
1、Insert the focus board _IO board wire(R35-M2007-00U) and the focus board _ main board line
R35-M2008-01U) into the connector corresponding to the focus board. Note the following figure: the
left connector is the focus board _ main board wire standing up, and the right connector is the focus
board _IO board wire lying down. The two heads are oriented whenfocusing board _ the main board line
is inserted. Short of 2 PIN on the inside , that isthe right side of the following figure, it cannot be inserted
backwards, otherwise there will be no focusing function.

2、Lock two focus board screws（R56-B2045-AB2）

This lack of 2
PIN Focus board _IO
board wire

Focus board _
mainboard wire Focus board
screw *2

3、Arrange the two wire in the line slot of the top cover

line slot

Fold the wire down

vertically, like this
red line

NOTE：After replacing the Focus Board(Webcam Module),you need to go into factory mode for
motor auto init.If you don't,you may not have autofocus.Please find and refer to the following

section description: Required Settings after hardware replacement

ViewSonic Corporation 17 Confidential - Do Not Copy M2

 三，Installation of main board components（R41-M2001-MA01S-ZJ）
1、Put the main board into the top cover, insert the interface end first, lock the four tapping screws
(R56-B2045-AB1), pay attention to check whether the main board 3005 chip heat sink installed before
installation, 838 thermal conductive silicon pad (R74-7W03-003) is pasted, interface conductive sponge
(R71-M2011-04) is pasted. As is shown in

3005 chip
heat sink

Tapping
838 thermal conductive screw*4
silicon pad
R74-7W03-003 The interface end is
inserted diagonally
interface conductive first
sponge

2、In turn, the p-senser_ir wire and the focus board _ main board wire, main board _IO board FPC
wire(R35-M2010-05) are inserted into the corresponding connector of the main board.
And arrange the wire in the line slot of the top cover

Focus
line slot

IR line slot

Motherboard _IO
board FPC flat cable
R35-M2010-05

P-senser_IR
wire

Focus board
- main board
wire

ViewSonic Corporation 18 Confidential - Do Not Copy M2

 NOTE：After replacing the main board,you need to go into factory mode and do the following:
horizontal trapezoid correction、motor auto init 、Color coordinate adjustment. Please find and

refer to the following section description: Required Settings after hardware

replacement

四 、 Installation interface sheet metal parts (R59-M2A02-K40) and interface copper pillars
(R59-M2A03-B00)
1、Screw the two connection copper pillars clockwise on the Interface sheet metal with hexagon socket
copper sleeve
2、Take the finished interface sheet metal parts as shown in the following figure to press the installation
direction on the main board, pay attention to check the interface should have conductive sponge. The
left and right screw holes are aligned to the main board corresponding to the screw holes
3、Take two tapping screws and use a screwdriver to lock the interface sheet metal parts on the main
board

screw*2
（R56-B2045-AB1）

interface sheet metal interface copper

pillars *2
parts（R59-M2A02-K40）
（R59-M2A03-B00）

ViewSonic Corporation 19 Confidential - Do Not Copy M2

 五、Install the heat sink to the optical engine

1、Insert the thermal conductivity silica gel at the interface between the optical engine and the heat sink
2、Take 6 screws(R57-B2860-11) and use the screwdriver to fix the optical engine and heat sink.

thermal conductivity
silica gel(R74-7W03-001)

Insert the Screws*6

thermal
conductivit
y silica gel

thermal conductivity
silica gel(R74-7W03-002)

六、Optical engine wire arrangement

1、Insert the the light coupling wire, the vibrator mirror FPC wire, the optical engineR, G, B, PB lamp wire
into the corresponding connector of the optical engine. See figures 5.1 and 5.2

Pay attention to plug tightly in place, pay attention to check the outside of the vibrator mirror FPC wire is
covered with a layer of conductive cloth, the optical engine R, G, B, PB lamp line should be a magnetic
ring
2、Fix the vibrator mirror wire on the DMD wire of the optical engine with the vibrator mirror conductive
cloth. Note that the connector end of the vibrator mirror wire should be reserved with a point of length
and should not be bent too tightly.
Arrange the light lines of R, G, B and PB, and the direction is shown in figure 5.3

ViewSonic Corporation 20 Confidential - Do Not Copy M2

 Optical engine PB
light wire Optical engine G light
（R35-M2004-00U） wire the light coupling wire
color：black （R35-M2002-05U） （R35-M2005-00U）
color：green

Optical engine B light Optical engine R light the vibrator mirror

wire wire FPC wire
（R35-M2002-05U） （R35-M2002-05U） （R36-M2009-05-ZJ）
color：blue color：red
figure 5.1 figure5.2

thevibrator mirror
conductive cloth
（R71-010920-003）

opticalenginelampwire
arrangewire direction
figure5.3

七、Optical engine into the top cover

1、Hold the heat sink fins of the optical engine by hand, align the installation position, check the
condition of no pressure onwire, press down the whole unit of the optical engine, pay attention to the
positioning hole of the optical engine to align with the corresponding positioning hole before pressing
down, to avoid the pillars misalignment. As shown in figure 6.1/6.2

ViewSonic Corporation 21 Confidential - Do Not Copy M2

 Optical engine When installing, align
positioning hole this end with the
mounting bit

Note to avoid the

optical engine DMD
wire under the main
board

When assembling, put the

lamp wires to one side first to Optical engine lens holder
avoid being pressed to the has a convex point position
wire by the Optical machine downwards
fixed pillars colloid

figure6.1 figure6.2

2、Screw position as shown in figure 6.3, lock seven tapping screws. Take air duct rigid foam and stick air
duct rigid foam gum on the bonding surface. Align the cover on the left to protrude the bone, and glue it
to the optical engine. Note before installing the optical engine to check whether the main board 838
chip has been pasted with thermal conductive silicon pad(R74-7W03-003), if the optical engine is
repaired removed, should check whether thermal conductive silicon pad has been glued to the optical
engine 838 chip heat sink.

Air duct rigid foam

(R74-M2008-14)

Mainboard 838 chip on

the thermalconductive
silicone pad
Tapping screw*7

figure6.4

figure6.3

ViewSonic Corporation 22 Confidential - Do Not Copy M2

 3、As shown in figure 6.5, connect the wire arrangement of the vibrator mirror and the DMD wire
arrangement of the optical engine on the corresponding connector of the mainboard
4、As shown in figure 6.6, theconductive cloth of the fan and optical engine FPC and the acetate cloth of
the connector of the main board according to the requirements of graphic stick better

Optical engine DMD wire alignment main Fan with optical machine FPC
board corresponding connector, pay to ground conductive cloth
attention not to dislocation, when flatten （R71-010935-001）
down, hear a click, make sure to buckle

The conductive cloth

should be bent down to
90 degrees to avoid
interference with the
The vibration mirror is inserted into the fan holder
corresponding connector on the main board. It
cannot be inserted at an angle. Align the plug
The conductive cloth should be
to the bottom and lock the connector
glued to the wire of the vibrating
mirror

Main board connector

acetate cloth
figure6.5 figure6.6
（R71-M2012-02）

NOTE：After replacing the Optical engine,you need to go into factory mode and do the following:
motor auto init、Color coordinate adjustment. Please find and refer to the following section

description: Required Settings after hardware replacement

ViewSonic Corporation 23 Confidential - Do Not Copy M2

 八、Install the fan fixed holder(R54-M2B09-PA)
1、Take the fan fixed holder and align the positioning holes with the three positioning pillars
corresponding to the top cover to ensure that the positioning pillars have penetrated the corresponding
positioning holes of the holder
2、Take 5 tapping screws and lock them into the 5 screw holes corresponding to the holder

positioning pillars
Tapping screw*5 *3
（R56-B2045-AB1）

九、Fixed optical engine R, G, B, PB lamp wire, according to the wire color, red - green - blue - black
sequence through the line slot into the corresponding main board connector
Note that the connector should be inserted to the bottom, and the wires should be arranged after the
connector is inserted. The magnetic ring should be arranged in a word near the end of the cover wall.
Pay attention to plug as much as possible on the magnetic ring wire tension, to avoid too loose after the
plug.

red grenn bule black

Line slot

ViewSonic Corporation 24 Confidential - Do Not Copy M2

 十、Install the speaker(R29-852704-04A)
1、When taking out the speaker, pay attention to check that screws or other foreign matters cannot be
stuck to the speaker diaphragm. The speaker wire should be round into a magnetic ring in advance, as
shown in figure 9.2
Insert the speaker screw hole into the speaker screw pillars corresponding to the top cover, and then
take three speaker screws and lock them into the corresponding screw positions, as shown in figure 9.1

Speaker screw*3 The speaker wire should

（R56-B6080-AB Line slot be round into a magnetic
ring in advance

Insert main board connector

(SPK next to it)
figure9.1 figure9.2

十一、Install the fan（R30-M29027-210）

1、Insert the fan into the corresponding connector on the main board, as shown in figure 10.1
2、Lay the fan flat on the fan fixed holder(R54-M2B09-PA), be careful not to press the optical enginewire.
Lock three screws
3、Affix a fan seal acetate cloth between the fan and heat sink fins, align the left lower edge to be pasted,
press flat after paste.

Tapping screw*3
FAN insert main board （R56-B2045-AB1）
connector (with the word FAN
next to it)

fan seal acetate cloth

（R71-M2012-01）
figure10.1 figure10.2

ViewSonic Corporation 25 Confidential - Do Not Copy M2

 十二、Install IO board components（R41-M2002-MA01S-ZJ）
1、Align the positioning hole of IO borad with the cover corresponding to the positioning pillars, and lock
the four tapping screws around. Lock two interface copper pillars screws in the middle, pay attention to
the two kinds of screws are not the same, can not be mixed, tapping screw is the point of tapping,
interface copper pillars screw is flat head machine teeth.

Tapping screw*4 interface copper pillars

（R56-B2045-AB1) screw *2(R57-B2860-12)

2、Arrange the optical engine motor wire, mainboard-io board wire arrangement, focusing board-io
board wire arrangement, and the light coupling wire arrangement in line slot, and insert the
corresponding connector of IO board in turn, that is according to the principle from right to left. Pay
attention to the main board -IO board wire inserted after the connector black lock button down
3、Attach the fan and optical engine FPC conductive cloth to the fan and IO board, as shown in the figure

Focus board -Io

Line slot
boardwire
the light coupling
wire
Motor wire

he fan and optical engine

Mainboard -IO FPC conductive
board wire clothR71-010935-002

ViewSonic Corporation 26 Confidential - Do Not Copy M2

 十三、Install the bottom cover components（R54-M2B03-PA-ZJ）
1、Check that there is no material leakage in the bottom cover components (see RSPL assembly list),
Bottom cover components alignment interface end buckle
2、As shown in figure 12.1, lock five tapping screws
3、Screw three rubber pads R54-M2001-TPU) in the corresponding position of the bottom cover in a
clockwise direction, as shown in figure 12.1, 1, 2 and 3.
4、Fuselage label according to the corresponding market choice. When labeling according to the bottom
cover template labeling reference alignment

1 Tapping screw*5 2
R56-B2045-AB1 bottom cover
components
R54-M2B03-PA-ZJ
labeling
reference
position

figure12.1
figure12.2

ViewSonic Corporation 27 Confidential - Do Not Copy M2

 十四、Install the optical engine lenscamera（R60-M2003-00）
1、Note that the glass lens backing has been pasted on the inspection surface cover in advance. Check
that the p senser soft rubber sleeveis not pressed by the cover
2、Take two infrared filters with tweezers, tear off the protective film, pay attention to keep it clean and
put it into the position as shown in figure 2, with the gum hollow out. Tear off the optical engine lens
protection film and camera protection film to ensure the optical engine lens is clean. If it is not clean,
please use lens cleaning cloth to touch 99.99% alcohol for cleaning.
3、Through the back glue torn hand, shake off the back glue from type paper.
Take the glass lens, pay attention to distinguish the front and back and left and right direction, bright
surface is the appearance of the surface, slightly thick surface is the adhesive surface. Left and right
direction according to the lens two transparent hole location. Align the groove edges of the surface shell
lens and flatten them down until they are installed in place. Make sure the gum and glass are fully
bonded
Infrared filter
R74-M20HW-010 Glass lens
R60-M2003-00 finish

Hand back
glue tear
Glass
lens gum

1 2 3 4

ViewSonic Corporation 28 Confidential - Do Not Copy M2

 Software upgrade
1.type-c upgrade

Using PC which has Windows 10 systems, a type-c data transmission line (USBA at one end and
type-c at the other) is used. The USBA interface is plugged into the PC, and the other end is
plugged into the projector type-c interface. After connecting with type-c, please check whether
the device administrator of PC has added a "Billboard" device

① Open the "software upgrading" file to enter "CH7211UpdatePackageV2. 0 _20190828" file,

open the CH7211UpdateCallerV2. 0. Exe, the following figure

ViewSonic Corporation 29 Confidential - Do Not Copy M2

 ② After opening the dialog box will pop up, select type-c APPLICATION, and execute "VERSION",
it will show the current IC FW VERSION, so you can be sure to have caught IC

③ Execute "Browse" and select FW, and then execute "UPDATE"

ViewSonic Corporation 30 Confidential - Do Not Copy M2

 2．Mcuupgrade

① Connect micro usb to the rear port of the projector and connect the other end to the
computer

② Plug the adapter into the projector, red light can be, do not have to boot

③ After confirming the st-link V2 connection, open the "software upgrading" file → open the
"M2_mcu_software_191212" file → click the "STVP" file → enter "stvp.exe".

ViewSonic Corporation 31 Confidential - Do Not Copy M2

 ④ Click File→open, select McU191212

⑤ Select arrow 1 to start the upgrade, after the upgrade arrow 2 will show a successful upgrade

ViewSonic Corporation 32 Confidential - Do Not Copy M2

 3.TIUpgrade

① Connect micro usb to the rear port of the projector and connect the other end to the
computer

② Adapter plug into the projector, boot

③ After connecting, open "software upgrading" File→ click "DLP Composer (TM)" File→open
"DLP Composer v13.6.3.4426 Setup", select File→open, and click thearrow to open, as
shown below

ViewSonic Corporation 33 Confidential - Do Not Copy M2

 ④ Select "Projector Control" in the new dialog box that pops up and then execute "Read Flash
Version" to view the current Flash Version

ViewSonic Corporation 34 Confidential - Do Not Copy M2

 ⑤Click "ASIC Options Manager" and then execute "download" to download and update

二、Number burn

1.Burn the Mac address

（1） Create a new macaddress.txt file in U disk root directory
（2） Place the macAddress code in the file “macaddress.txt”, for example:
54:EE:76:AD:27:B1
54:EE:76:AD:27:B2
54:EE:76:AD:27:B3
54:EE:76:AD:27:B4
54:EE:76:AD:27:B5
54:EE:76:AD:27:B6
54:EE:76:AD:27:B7
54:EE:76:AD:27:B8
The file “macaddress.txt” can place N macAddress codes.
（3） Insert the U disk into the main board USB interface, open the factory menu Pager5, click Write
Mac automatic Write.
（4） If the Show Mac display changes, it means that the recording is successful, and the restart
machine takes effect.
（5） The used macAddress code is automatically followed by "USED" to represent it used. Such as:
54:EE:76:AD:27:B1 USED

ViewSonic Corporation 35 Confidential - Do Not Copy M2

 2.Serial Numberburn
(1) Create a new “sn.txt” file in the U disk root directory.
(2) Place the sn code in the “sn.txt” file, such as:
VT9200101245
VT9200101169
VT9200101169
Sn.txt file can be placed N sn codes
(3) Insert the USB disk into the USB interface of the main board, open the factory menu Pager5, and click
Write Serial Number to Write automatically.
(4) If the Serial Number shows a change, it means the burn was successful and the reboot takes effect.
(5) The usedsn code will be automatically followed by "USED" to represent itused. Such as:
52aa24ce-8c26-4bc3-b697-0397a379c904USED

3.Burn HDCP1.4and HDCP2.2

(1) Create a file named HDCP and hdcp2 in the U disk root directory.
(2) Put the HDCP 1.4 file to be burned in the HDCP file. The naming rule of the HDCP key file shallbe led
by 0, with no more than six digits, as shown in the following figure

(3) Put the hdcp2.2 file to be burned in the hdcp2 file, and the naming rule of the HDCP key file shall be
led by 0 and no more than six digits, as shown in the following figure

ViewSonic Corporation 36 Confidential - Do Not Copy M2

 (4) Insert the U disk into the main board USB interface, open the factory menu Pager5, click Write HDCP
or Write HDCP-2 automatically Write.
(5) If the display of Write HDCP or Write hdcp-2 changes, it means that the HDCP KEY burns successfully,
and restart the machine to take effect.
(6) The used HDCP file, automatically add the suffix“.USED” after the name to represent it used. Such as:
HDCPkey1234.bin.USED

4、Deviceid and apikey burn steps

(1) Create a new “deviceid_apikey.txt” file in the U disk root directory.
(2) Place deviceId and apikey in the “deviceid_apikey.txt” file, separated by Spaces,such as:
10006ff8cf 52aa24ce-8c26-4bc3-b697-0397a379c904
10006ff8d0 72747f50-a4eb-4d21-a500-c8f7b6f3763d
10006ff8d1 2e03da8e-ea89-4688-8766-91cb2395d5bf
The first is deviceId and the second is apikey, note that they must be separated by a space. The
deviceid_apikey.txt file can place N deviceId and apikeys.
(3) Insert the U disk into the main board USB interface, open the factory menu Pager5, click Write
deviceIdapikey to Write automatically
(4) If the display of Show deviceID and Show apikey changes, it means that deviceIDapikey burns
successfully, and the restart machine takes effect
(5) the used ID and apikey are automatically followed by "USED" to represent it used. Such as:
10006ff8cf 52aa24ce-8c26-4bc3-b697-0397a379c904USED

ViewSonic Corporation 37 Confidential - Do Not Copy M2

 Note: factory menu enter way

After starting up, click "setup" → "information", press the remote control "up 、down、 up 、down、
up 、down " in the "information" interface, and then press "ok" to enter "factory mode".

Required Settings after hardware replacement

1.After the replacement of the main board should be horizontalrelatively correct: The projector is
placed on a horizontal table ,Pack up support,the pad will tighten,after the projector boot,
successively enter the "setting" → "basic Settings" → "trapezoid distortion", "longitudinal trapezoid
correction" and "horizontal trapezoid correction" values to zero, and then check whether the
projection picture is normal. Finally, open factory mode and go to page2, move the cursor to
AutoKeystone Cal, and change N to Y.

2.After replacing main board, optical engine and Focus Board(Webcam Module), motor auto init is
required: after the projector is turned on. Click "Settings" → "information" in turn, press the "up,
down, up ,down,up ,down " key of the remote control in the "information" interface, and then
press "OK" to enter "factory mode", enter Page3, and move the cursor to the last item motor auto
init. Set N to Y and exit after the screen is stable. (Note: do not move the projector during reset.
Replace the main board without resetting, there will be no auto focus function)

3、After the replacement of the main board or optical englin to re-adjust the color coordinates.In
the full darkness,projectoron,playing 70% white pectures on a usb flash drive.Set the color mode to
movie,At this signal,Remote control press down right down right down right to enterfactory
mode,Go to page 2,Adjust the first term and the third term(CT R Gain、CT B Gina)
Color x y
Color Coordinate (Movie mode@70IRE)
White 0.313±0.003 0.329±0.003

ViewSonic Corporation 38 Confidential - Do Not Copy M2

 factory mode
settings---information，Remote control input"Up Down Up Down Up Down OK"
Can not be adjusted
can be adjusted，press the left and right buttons of the remote
can be adjusted，Select the left and right keys and press ok
can be adjusted，Press OK key
OSD
Factory
OSD range defaul Remark
function
t
Page1
Used to determine whether USB is
USB port mode Mstar/TI Mstar
the debug port for TI
OSD reset Y/N N Same function as OSD reset all
Reset all items to factorv settings,
Factory adjustment is
Shipping reset Y/N N
excluded(Color/EDID/HDCP/ISF...
)
Factory hard Reset all items to factorv
Y/N N
reset settings
Model Name ViewSonic M2
MCU version xxxxxx MCU FW version（Mstar）
FPGA version x-x-xxx-x-x FPGA FW version（TI）
Flash version x-x-x Flash FW version（TI）
FanTable
MF90201V1-C010-S9A
version FAN table FW
Date yyyy.mm.dd xx：xx FW date
FW factory
version
FW user version
Page2
Color mode:Movie value, can be
CT R Gain 0~255 128
adjusted
Color mode:Movie value, can be
CT G Gain 0~255 128
adjusted
Color mode:Movie value, can be
CT B Gain 0~255 128
adjusted
Color mode:Movie value, can be
CT R Offset 0~255 128
adjusted
Color mode:Movie value, can be
CT G Offset 0~255 128
adjusted
Color mode:Movie value, can be
CT B Offset 0~255 128
adjusted
AutoKeyStone
Y/N N Keystone calibration
Cal
AutoKeyStone x:xxx y:xxx z:xxx Coordinate values

ViewSonic Corporation 39 Confidential - Do Not Copy M2

 offset
AngleCalValue 0~90 0 keystone calibration values
AutoKeyStone
has been Y/N N check for calibration?
calibration?
ProximitySenso
r Logcat Open/N N Read the Psensor value
ProximitySenso
r xxx Displays the Psenser value
Adjust the value of
ProximitySenso psenser(Adjust the effective
r 0/250 40 distance of Eye Protection)
Page3
Current Hours 0~65536 0 Total working hours at present
Total working hours from reset to
Shipping Hours 0~65536 0
now
Total working time ,cannot be
Total Hours 0~65536 0
reset
Reset All Hours Y/N N Recalculate time after reset
If the system temperature
R LED Error 0~255 0 exceeds 60℃ a minute,Record at
a time
Error Count
Y/N N Reset all current error counts
reset
R LED 0~200°C System temperature
Air inlet 0~200°C Air inlet temperature
Manually adjust the speed of the
Use Fan table fan（Y:Cannot adjust，N: Can
Y/N Y adjust）
Can manually adjust the value,,
Fan1-Target duty10~90 duty40 Restore to the initial software
value after reboot
Can manually adjust the value,,
Fan1-Target duty10~90 duty40 Restore to the initial software
value after reboot
Motor Auto Init Y/N N Reset function of focusing motor
Page4
No input signal, TI DMD directly
DMD full on Y/N N
displavs an white screen
Select test image，need to be in
Test pattern
off/White/Red/Green/Blue/Black off source
off/White/White_70/White_30/Black/Red/Green/Blu Select test image，need to be in
Test pattern PQ
e off source
FPGA Judge whether the vibroscope is
Calibration TBG Y/N Y working or no
Actuator
control Y/N N vibroscope is ON or OFF

ViewSonic Corporation 40 Confidential - Do Not Copy M2

 OTA TEST path N/Y N Test path for OTA upgrade
PQUart off/on off Read the PQ value ON or OFF
updaBin Upgrade FW with USB(.bin)
Burn-in Mode off/on off Aging mode ON or OFF
Adjust the current of the red
DLP R
0~1000 380 light
Adjust the current of the green
DLP G
0~1000 520 light
Adjust the current of the blue
DLP B
0~1000 520 light
Adjust the current of the PB
DLP P
0~99 20 light
Page5
Write Mac Write Mac
Write HDCP Write HDCP 1.4
Write HDCP-2 Write HDCP 2.2
Write EDID Write EDID
Write EDID-2 Write EDID-2
Write
Write deviceIDapikey
deviceIDapikey
Write Serial
Write Serial Number
Number
Update PQ /
Show info /
Show deviceID Show deviceID
Show apiey Show apiey
Show Number Show SN
Show MAC Show MAC
Displays the bar code for Mac and
Show All
deviceID

ViewSonic Corporation 41 Confidential - Do Not Copy M2

 Firmware upgrade

1. U disk upgrade: insert the U disk with the. Zip upgrade file, turn on the projector, and then click
settings → firmware update →softwareupdateby USB

2.OTAupgrade：

When a new version is updated, the projector is connected to the network, and there will be a
pop-up prompt. Press the prompt to select to update to the latest version. Be careful not to power
down during the upgrade process, and ensure the network is smooth.

ViewSonic Corporation 42 Confidential - Do Not Copy M2

 Panel function description

Air inlet

Shake
handshandle

Micro5PIN:TI
Software
upgrade USB wifi dongle
jack

Autofocus eyecare
camera senser

SPK IR receiver
mouth

Optical Engine
show

ViewSonic Corporation 43 Confidential - Do Not Copy M2

 Type C jack：Connect
to the phone screen，
power
insert 15V3A
indicator，turn
portable power
Air outlet on/off on blue,Standby
source can make the
red
projector work

DC jack

HDMI jack

IR receiver
mouth

TF card jack USB3.0 jack Audio out

ViewSonic Corporation 44 Confidential - Do Not Copy M2

 Exploded View and Recommend Spare parts List

Packing Exploded View

ViewSonic Corporation 45 Confidential - Do Not Copy M2

 Total Exploded View

ViewSonic Corporation 46 Confidential - Do Not Copy M2

 Recommended Spare Parts List

RECOMMENDED SPARE PARTS LIST（M2）

ViewSonic Model Number: VS17808

Serial No. Prefix: VT9

Item Category Part Name Description Ref. P/N Ref. NO

DA-90J19,Input:100-240V 50-60Hz 1.5A

1 Power Adapter R41-M2ADT-18 5
Max,Output:19V 4.74A, DC5.5-2.1
TYPE-C cable.HCC-C02 USB3.1 TYPE C TO C port,
32AWG core of cable, length:1M black. The entire
2 Signal Cable R35-TCTC-011 3
cable should be shielded ,E-mark is unnecessary
for cables;
CT-USB3-7632 2T2R 300Mbps 2.4G+5G WIFI Module
3 Wireless Card R43-USB01-001 8
Dongle 50.25*18.3*8.72mm
7# battery Toshiba carbon battery R03UG 1.5V
4 battery long 44.1mm* diameter 10.2mm(Remote control R71-080307-050 7
)
5 power cord EU/KR L=1m UE-312/UE-323 H03VV-F 3G0.75mm² R37-K0100-OHG 4

6 power cord CHN L=1m UE-303 /UE-323 / H03VV-F 3G0.75mm² R37-K0100-CCC 4

Accessories:
7 [Adapter, Remote power cord US L=1m UE-321/UE-323 / UL SVT 3X18AWG 105℃ R37-K0100-CMG 4
Controller, Power
8 power cord UK L=1m UE-324 /UE-323 / H03VV-F R37-K0100-YGG 4
Cord, External
3G0 75mm²
Cables]
9 power cord TW L=1m PHP-301/PHS-305/VCTF 3X0.75mm² R37-K0100-TWG 4
250g double copper paper,Double-sided color
10 Warranty card R64-M21191-029
printing,size：111*91MM
M2 Manual Multi-language 148 * 105mm Expanded
size 297 * 420 Double copper 128G Single black
11 Qucik Start Guide (QSG) R65-M20001-M100 2
fold with LOGO: M series lamp Free Smart Theater
Quick Start Guide
TYX1818-IR-009 159.86*42*16MM PC/ABS IR(λ940
12 Remote control(IR) ±50mm) chip：TC1617 3V DC 2.2-3.4V 8m/DC R81-TYX1818-IR 6
3V with LOGO：ViewSonic
TYX1818-BLE-RCU_03 ，159.86*42*16MM，MCU
13 Remote control(BT/IR) R81-TYX1818-BT 6
chip:8762，BT /IR LOGO：ViewSonic
14 Main Board Main PCBA Module (Mstar/IO)， M2_REF_VER_V05 R41-M2001-MA01S-ZJ 14
15 PC Board Assembly: IO Board M2_IO_V05 (IO) R41-M2002-MA01S-ZJ 15

16 [WW、VSCN PCBA] IR Board P sensor_IR_V05 (IR CHQD-1-H + P senser R41-M2003-MA01S-ZJ 16

EM30918)
17 focus Board AS-2MUSB02 Autofocus R41-M2004-MA01-ZJ 17

18 Top Cover（WW） combination structure material,top R54-M2B01-PAPS-ZJ 33

LOGO:ViewSonic,side LOGO :harman/Kardon
Cabinets: combination structure material,top
19 [Front Bezel, WW、 Top Cover（VSCN ） R54-M2B10-PAPS-ZJ 34
LOGO:ViewSonic,side LOGO :JBL
20 VSCN Covers, Base Bottom Cover combination structure material R54-M2B03-PA-ZJ 35
Assembly]
21 Fan holder black ,PC+ABS R54-M2B09-PA-ZJ 36

22 Flat cable (FPC) PIN Same direction,FPC,4PIN L=90mm,Black R36-M2009-05-ZJ 21

shield,External conductive cloth
23 Flat cable(FPC) PIN different directions，FPC 40PIN，L=60mm Black R35-M2010-05 22
red wire L=225mm, UL3302 AWG24#
24 Wire 31/0.11,L=255mm, 2 ends with 8PIN PH1.5 R35-M2001-02U-ZJ 23
terminals, same surface with overgild,with the
green wire L=235mm, UL3302 AWG24#
25 Wire 31/0.11,L=255mm, 2 ends with 8PIN PH1.5 R35-M2002-05U-ZJ 24
terminals, same surface with overgild,with the
blue wire L=245mm, UL3302 AWG24#
26 Wire 31/0.11,L=255mm, 2 ends with 8PIN PH1.5 R35-M2003-06U-ZJ 25
terminals, same surface with overgild,with the
Cables: [WW、VSCN
black t wire
i L=255mm, UL3302 AWG24#
internal
27 Wire 31/0.11,L=255mm, 2 ends with 8PIN PH1.5 R35-M2004-00U-ZJ 26
Cables/wires]
terminals, same surface with overgild,with the
Connector in the same direction,3PIN UL3302
28 Wire R35-M2005-00U 27
AWG28# 19/0.11,L=160mm black wire
black wire length 130mm, wire diameter 0.6mm,
29 Wire both ends with terminal 8pin PH0.8 in same R35-M2006-00U 28
surface
black wire length 200mm, wire diameter 0.6mm,
30 Wire both ends with terminal 8pin PH0.8 in same R35-M2007-00U 29
surface
black wire length 170mm, wire diameter 0.6mm,
31 Wire both ends with terminal 8pin PH0.8 in same R35-M2008-01U 30
surface. less two cable

ViewSonic Corporation 47 Confidential - Do Not Copy M2

 RECOMMENDED SPARE PARTS LIST（M2）

ViewSonic Model Number: VS17808

Serial No. Prefix: VT9

Item Category Part Name Description Ref. P/N Ref. NO

32 Label RG2 label,80g Coated paper,Yellow background,size R64-M26223-029

33 label PET silver dragon paper,size：50*130MM R64-M25014-029

34 Label PET silver dragon paper,size：50*130MM R64-M25015-029

35 Label color box label,80g Coated paper,size：93*103MM R64-M29313-029 13

Documentation:
36 [Quick Start Guide, Label color box 4 im 1 S/N label,80g Coated paper,size： R64-M25490-049 11

37 CD Rom, label cartoon box label,80g Coated paper,size：100*175M R64-M25490-029

Label/Sticker]
38 Label Anti demolition label,Round transparent R64-M24040-029 9
adhesive PVC size：40*40mm
39 Label Hi-Pot OK label,80g Coated paper,size：50*17MM R64-M25017-029

40 label Warranty card S/N label, 80g Coated paper,size： R64-M23509-029

41 label Warranty card CN label,80g Coated paper,size：25*4 R64-M22546-029

model:P13HA-MF,LED(RGBB) 0.33 1080P DLP，TR：
42 Electronic Optical Engine 1.23，brightness:460LM +Plastic R32-DLP02-AH01-ZJ 18
Components: [LCD stent+Conductive cloth
Panel, Speaker, and
WW、VSCN Electronic E060-0479-001,BOX cavity speaker Frequency：110-
43 Modules] Speaker 20KHz,Fb:160±10%,DCR:3.6±7%. 4PIN wire length R29-852704-04A-ZJ 20
160mm with terminal
44 Heat Sink Copper pipe+aluminium R59-M2A01-0A9-ZJ 52
45 Tapping screw PA 2.0*8 mm,∮6.0 T2.0 BZN R56-B6080-AB1 46
46 Machine screws PM2.0*4 mm,∮3.5 T1.2 BZN R57-B2860-12 50
47 Machine screws PM1.7*6.0 ∮3.0 T1.0 BZN R57-B2860-11 51
48 Tapping screw PA1.4*3.5mm,∮2.5 T0.5 BZN R56-B2045-AB2 49
49 Hardware: [Screw, Tapping screw PA2.0*6.0mm,∮3.5 T1.2 BZN R56-B2045-AB1 48
Bracket, Hinge]
50 Tapping screw CB1.4*2.0mm，∮4.0MM，T0.5 BZN R56-B4020-BF1 47
51 Rubber pad black TPU,hardness:50,+copper nut R54-M2001-TPU 37
thick :1mm ,total length 101mm,mold is bent and
52 Interface sheet metal R59-M2A02-K40 38
formed
53 pillars Material is puslitative,M3 16.1mm*4 R59-M2A03-B00 39
54 Glass Lenses Size:70.9*32.1*0.7mm，transmittance＞98% R60-M2003-00 40
Miscellaneous: SUNON DC brushless blower ,Model:MF90201V1-C04C-
55 [Switch, Fan, Rubber FAN S99 DC 12V/272MA
R30-M29027-210 19
]
56 color box（WW） paper box +printing,LOGO:harman/Kardon R68-M20001-24Y-ZJ 12
57 color（VSCN ） paper box +printing,LOGO:JBL R68-M20008-24Y-ZJ
Packing Material: K=K,paper：200G,printed in black,bonded
58 [Carton, Box, Foam, carton box molding,size：602*585*174MM
R68-M20001-2CY
Bags]
Oxford cloth,LOGO(ViewSonic),230*230mm,model：
59 Hand bag R66-M20002-R01 1
PJ-CASE-012
60 Non-woven bag Black non-wonen fabric,SIZE:215*222*57mm R66-M20001-R01 10
61 Windbreak foam EVA,38°,10mm*26mm*0.5mm, R74-M2008-11 41

62 Air duct rigid foam PORON ，47mm*22mm*6mm R74-M2008-14-ZJ 42

63 Acetate cloth black 145*10mm*0.2mm R71-M2012-01 43

64 Acetate cloth black 40mm*6mm*0.2mm R71-M2012-02 44

65 supplementary Infrared filter black,9*9*0.25mm R74-M20HW-010 45
material
66 Conductive cloth black 35*22*0.1mm R71-010935-002 31
67 Conductive cloth black 20*10mm*0.1mm R71-010920-003 32

68 Thermal conductivity silica Coefficient：7W,thick:0.5mm,20mm*15mm R74-7W03-001 53

gel
Thermal conductivity silica
69 Coefficient：7W,thick:0.5mm,30mm*20mm R74-7W03-002 54
gel

ViewSonic Corporation 48 Confidential - Do Not Copy M2

 RECOMMENDED SPARE PARTS LIST (M2)
ViewSonic Model Number: VS17808
Serial No. Prefix: VT9
Rev: 1n
Item Category Part Name Description Region ECR/ECN ViewSonic P/N Supplier P/N Compatibilit Remark Chinese
Accessories: [Adapter, Battery, DA-90J19,Input:100-240V 50-60Hz 1.5A Max,Output:19V 4.74A, DC5.5- VS-E200168 Removed on 04/20/2020 VS-
1 Adapter WW R41-M2ADT-18 1 适配器
Remote Controller, Power 2.1(Power Adapter) E200225 Added on 04/29/2020 A-00010361
Cord, External Cables, Mouse, VS-E200168 Added on 04/20/2020 Update on
2 Keyboard] Adapter Adapter GM95-190473-F VSA/VSE/VSI 01/20/2021. VS-ECN-JIP-210167 Updated on R41-M2ADT-19 1
03/19/2021 A-00010388
TYPE-C cable.HCC-C02 USB3.1 TYPE C TO C port, 32AWG core of cable
3 Signal Cable length:1M black. The entire cable should be shielded ,E-mark is unnecessary for WW R35-TCTC-011 1 TYPE-C cable type c线
cables; CB-00013182
TYX1818-IR-009 159.86*42*16MM PC/ABS IR(λ940±50mm) chip: TC1617 3V
4 Remote control WW R81-TYX1818-IR 1 Remote control(IR) (Keep for service)
DC 2.2-3.4V 8m/DC 3V with LOGO: ViewSonic (Remote control(IR) A-00010362
5 Remote control Remote control VS-E200454 Added on 09/07/2020 A-00010470 R81-18A007-IR 1
TYX1818-BLE-RCU_03 , 159.86*42*16MM, MCU chip:8762, BT /IR LOGO:
6 Remote control VSCN R81-TYX1818-BT 1 Remote control(BT/IR)
ViewSonic (Remote control(IR)) A-00010363
CT-USB3-7632 2T2R 300Mbps 2.4G+5G WIFI Module Dongle Update typo on 06/04/2021 per PE confirm w/o EC
7 USB Flash Drive WW R43-USB01-001 1 USB WIFI Dongle
50.25*18.3*8.72mm concern A-00010645
7# battery Toshiba carbon battery R03UG 1.5V long 44.1mm* diameter
8 Battery WW R71-080307-050 1 Remote controller(dry cell) 7#电池
10.2mm(Remote control battery) A-00010364
#7 battery,Gold Peak Group 24G R03 SIZE/FORMAT AAA 1.5V(Remote control
9 Battery WW R71-080307-051 1
battery) VS-ECN-JIP-210019 Added on 02/03/2021 A-00010550
10 Carry Bag Oxford cloth,LOGO(ViewSonic),230*230mm,model: PJ-CASE-012 (Hand bag) WW R66-M20002-R01 1 M2 projector and accessories are packed in this bag 手提袋
A-00010370
11 Carry Bag Black non-wonen fabric,SIZE:215*222*57mm (Non-woven bag) WW A-00010371 R66-M20001-R01 1 M2 projector is in the bag 保护袋
12 Power cord EU/KR L=1m UE-312/UE-323 H03VV-F 3G0.75mm WW A-00010365 R37-K0100-OHG 1
13 Power cord CHN L=1m UE-303 /UE-323 / H03VV-F 3G0.75mm VSCN A-00010366 R37-K0100-CCC 1
14 Power cord US L=1m UE-321/UE-323 / UL SVT 3X18AWG 105℃ WW A-00010367 R37-K0100-CMG 1
UK L=1m UE-324 /UE-323 / H03VV-F
15 Power cord WW R37-K0100-YGG 1
3G0.75mm² A-00010368
16 Power cord TW L=1m PHP-301/PHS-305/VCTF 3X0.75mm WW A-00010369 R37-K0100-TWG 1
PC Board Assembly: [All 如图示, 主板上有预加工如下物料：838导热硅
17 boards or PCBA] Main Board Main PCBA Module (Mstar/IO), M2_REF_VER_V05 WW R41-M2001-MA01S-ZJ 1 垫、3005导热硅胶垫、芯片散热器、散热器弹接
B-00015097 口导电海棉
18 IO Board M2_IO_V05 (IO) WW B-00015098 R41-M2002-MA01S-ZJ 1 M2 IO PCBA
19 IR Board P sensor_IR_V05 (IR CHQD-1-H + P senser EM30918) WW B-00015099 R41-M2003-MA01S-ZJ 1
2nd source. The materials of the old and new
20 Main Board Main PCBA Module (Mstar/IO), M2_REF_VER_V05 WW R41-M2001-MA02V-ZJ 1
VS-ECN-JIP-210361 Added on 06/24/2021 B-00015817 suppliers can be used together.
2nd source. The materials of the old and new
21 IO Board M2_IO_V05 (IO) WW R41-M2002-MA02V-ZJ 1
VS-ECN-JIP-210361 Added on 06/24/2021 B-00015818 suppliers can be used together.
2nd source. The materials of the old and new
22 IR Board P sensor_IR_V05 (IR CHQD-1-H + P senser EM30918) WW R41-M2003-MA02V-ZJ 1
VS-ECN-JIP-210361 Added on 06/24/2021 B-00015819 suppliers can be used together.
23 Cabinets: [Front Bezel, All R54-M2B01-PAPS-ZJ
Top Cover combination structure material,top LOGO:ViewSonic,side LOGO :harman/Kardon WW C-00014077 1 upper tooling module(Harman) 面壳组件（WW)
24 Covers, Base/Stand Assembly] Update Typo on 11/27/2020 R54-X10003-00BK-ZJ
25 R54-M2B10-PAPS-ZJ
Top Cover combination structure material,top LOGO:ViewSonic,side LOGO :JBL VSCN C-00014078 1 upper tooling module(JBL) 面壳组件（VSCN )
26 Update Typo on 11/27/2020 R54-X10008-00BK-ZJ
27 Bottom Cover combination structure material WW C-00014079 R54-M2B03-PA-ZJ 1 nether tooling module 底壳组件
PIN Same direction,FPC,4PIN L=90mm,Black shield,External conductive cloth
28 Cables: [All internal Flat Cable WW Update Typo on 05/18/2020 CB-00013183 R36-M2009-05-ZJ 1 M2 main board to light machine connection wire 振镜FPC排线
(FPC)
29 Cables/wires] Flat Cable PIN different directions, FPC 40PIN, L=60mm Black shield (FPC) WW CB-00013184 R35-M2010-05 1 M2 main board to IO board connection wire 主板-IO板 排线
red wire L=225mm, UL3302 AWG24# 31/0.11,L=255mm, 2 ends with 8PIN
30 Wire WW R35-M2001-02U-ZJ 1 M2 light engine connecting wire (red LED ) 光机R灯线
PH1.5 terminals, same surface with overgild,with the magnet rin CB-00013185
green wire L=235mm, UL3302 AWG24# 31/0.11,L=255mm, 2 ends with 8PIN
31 Wire WW R35-M2002-05U-ZJ 1 M2 light engine connecting wire (green LED) 光机G灯线
PH1.5 terminals, same surface with overgild,with the magnet rin CB-00013186
blue wire L=245mm, UL3302 AWG24# 31/0.11,L=255mm, 2 ends with 8PIN
32 Wire WW R35-M2003-06U-ZJ 1 M2 light engine connecting wire (blue LED) 光机B灯线
PH1.5 terminals, same surface with overgild,with the magnet rin CB-00013187
black wire L=255mm, UL3302 AWG24# 31/0.11,L=255mm, 2 ends with 8PIN
33 Wire WW R35-M2004-00U-ZJ 1 M2 light engine connecting wire (PB LED) 光机PB灯线
PH1.5 terminals, same surface with overgild,with the magnet rin CB-00013188
Connector in the same direction,3PIN UL3302 AWG28# 19/0.11,L=160mm black M2 light engine （light coupling) to IO board
34 Wire WW R35-M2005-00U 1 光耦线
wire CB-00013189 connecting wire
black wire length 130mm, wire diameter 0.6mm, both ends with terminal 8pin
35 Wire WW R35-M2006-00U 1 M2 IR Board to main board connecting wire P-senser_IR 排线
PH0.8 in same surface CB-00013190
black wire length 130mm, wire diameter 0.6mm, both ends with terminal 8pin
36 Wire WW R35-M2007-00U 1 M2 focus Board to IO board connecting wire 聚焦板_IO板线
PH0.8 in same surface CB-00013191
black wire length 170mm, wire diameter 0.6mm, both ends with terminal 8pin
37 Wire WW R35-M2008-01U 1 M2 focus Board to main board connecting wire 聚焦板_主板排线
PH0.8 in same surface. less two cable CB-00013192
Documentation: [Quick Start M2 Manual Multi-language 148 * 105mm Expanded size 297 * 420 Double coppe
38 Guide, CD Rom, Quick Start Guide (QSG) 128G Single black fold with LOGO: M series lamp Free Smart Theater Quick Start WW R65-M20001-M100 1 M2 user manual 快速使用指南
Label/Sticker] Guide VS-E200158 Removed on 04/20/2020 DC-00015917
128G double copper paper, double-sided monochrome printing,N3 fold and fold in
39 Quick Start Guide (QSG) half, expanded size :297*420MM, finished size VS-E200158 Added on 04/20/2020 Update Typo R65-M20002-M100
:148*105mm on 05/18/2020 DC-00015950
40 Warranty card 250g double copper paper,Double-sided color printing,size: 111*91MM VSCN DC-00015918 R64-M21191-029 1 保修卡
41 Label / Sticker RG2 label,80g Coated paper,Yellow background,size: 62*23MM WW DC-00015919 R64-M26223-029 1 Attach it to the bottom of the machine RG2标
42 Label / Sticker PET silver dragon paper,size: 50*130MM WW DC-00015920 R64-M25014-029 1 Attach it to the bottom of the machine 机身标（WW）
43 Label / Sticker PET silver dragon paper,size: 50*130MM VSCN R64-M25015-029 1 The label is attached to the bottom of the machine 机身标（VSCN）
DC-00015921
44 Label / Sticker color box label,80g Coated paper,size: 93*103MM WW DC-00015922 R64-M29313-029 1 The label is attached to the color box 卡通(盒子)箱标
45 Label / Sticker color box 4 im 1 S/N label,80g Coated paper,size: 54*90MM WW DC-00015923 R64-M25490-049 1 The label is attached to the color box 卡通(盒子)箱四合一S/N标
46 Label / Sticker cartoon box label,80g Coated paper,size: 100*175MM WW DC-00015924 R64-M25490-029 1 The label is attached to the cartoon box 卡通箱标
Stick on the second side of the color box,stick on the
47 Label / Sticker Anti demolition label,Round transparent adhesive,PVC size: 40*40mm WW R64-M24040-029 1 防拆标
DC-00015925 protect bag
48 Label / Sticker Hi-Pot OK label,80g Coated paper,size: 50*17MM VSCN R64-M25017-029 1 The label is attached to the bottom of the machine 高压测试合格标
DC-00015926
49 Label / Sticker Warranty card S/N label, 80g Coated paper,size: 35*9MM VSCN DC-00015927 R64-M23509-029 1 stick it on the warranty card 保修卡S/N标
50 Label / Sticker Warranty card CN label,80g Coated paper,size: 25*4.6MM VSCN DC-00015916 R64-M22546-029 1 stick it on the warranty card 保修卡CN标
51 Electronic Components: Webcam Module AS-2MUSB02 Autofocus (focus Board) WW E-00013725 R41-M2004-MA01-ZJ 1
[Optical Engine, Speaker, P13HA-MF, LED(RGBB) 0.33 1080P DLP, TR : 1.23, 460LM,focus motor(the
52 Optical Engine WW VS-ECN-JIP-210290 Removed on 05/31/2021 R32-DLP02-AH01-ZJ 1 M2 light engine combine 光机+散热器组件
Color Wheel, LCD Module] heat sink is assembled on the optical engine) E-00013726
P13HA-MF, LED(RGBB) 0.33 1080P DLP, TR : 1.23, 460LM,focus
53 Optical Engine WW VS-ECN-JIP-210290 Added on 05/31/2021 R32-DLP02-AH01-ZJA 1
motor+Thermal PAD*3 (not assemble on Optical Engine E-00014177
54 Thermal PAD Coefficient 7W, thick:0.5mm,20mm*15mm VS-ECN-JIP-210290 Removed on 05/31/2021 E-00013784 R74-7W03-001 included in OE
55 Thermal PAD Coefficient 7W,thick:0.5mm,30mm*20mm VS-ECN-JIP-210290 Removed on 05/31/2021 E-00013785 R74-7W03-002 included in OE
E060-0479-001,BOX cavity speaker Frequency: 110-20KHz,Fb:160±
56 Speaker WW R29-852704-04A-ZJ 1 腔体喇叭
10%,DCR:3.6±7%. 4PIN wire length 160mm with termina E-00013727
57 Lens Size:70.9*32.1*0.7mm, transmittance＞98% (Glass Lenses) WW E-00013728 R60-M2003-00 1 玻璃镜片
58 Hardware: [Screw, Bracket, Screw PA 2.0*8 mm,∮6.0 T2.0 BZN (Tapping screw) WW HW-00011774 R56-B6080-AB1 1 in speaker 喇叭螺丝
59 Hinge] Screw PM2.0*4 mm,∮3.5 T1.2 BZN (Machine screws) WW HW-00011775 R57-B2860-12 1 in IO board 接口铜柱螺丝
60 Screw PA1.4*3.5mm,∮2.5 T0.5 BZN (Tapping screw) WW HW-00011776 R56-B2045-AB2 1 focus Board 聚焦板螺丝
61 Screw PA2.0*6.0mm,∮3.5 T1.2 BZN (Tapping screw) WW HW-00011777 R56-B2045-AB1 1 Most locations,Reference pictures 自攻螺丝
62 Screw CB1.4*2.0mm, ∮4.0MM, T0.5 BZN (Tapping screw) WW HW-00011778 R56-B4020-BF1 1 in IR board IR板螺丝
63 Screw PM1.7*6.0 x diameter 3.0 T1.0 BZN（Machine screws VS-E200205 Added on 04/29/2020 HW-00011815 R57-B2860-11
64 Heat Sink Copper pipe+aluminium VS-E200205 Added on 04/29/2020 HW-00011814 R59-M2A01-0A9-ZJ
65 Shielding thick :1mm ,total length 101mm,mold is bent and formed (Interface sheet metal) WW HW-00011779 R59-M2A02-K40 1 Combined on the main board 接口钣金件
66 Pillar Material is puslitative,M3 16.1mm*4 WW HW-00011780 R59-M2A03-B00 1 Combined on interface sheet metal 接口铜柱
67 Miscellaneous: [Switch, Fan, Foot (Rubber Foot) black TPU,hardness:50,+copper nut (Rubber pad) WW M-00010201 R54-M2001-TPU 1 in Bottom Cover 机脚垫
68 Rubber Foot, Logo] Holder Fan holder WW M-00010202 R54-M2B09-PA-ZJ 1 on the main board 风扇固定支架
69 FAN SUNON DC brushless blower ,Model:MF90201V1-C04C-S99 DC 12V/272MA WW M-00010203 R30-M29027-210 1 M2 FAN 风扇
70 Sponge EVA,38°,10mm*26mm*0.5mm (Windbreak foam) WW R74-M2008-11 1 Stick on the plastic shell on the side of the speaker. 挡风硬质泡棉
M-00010204
71 Sponge PORON , 47mm*22mm*6mm (Air duct rigid foam ) WW M-00010205 R74-M2008-14-ZJ 1 Dtick on the Optical Engine 风道硬质泡棉
72 Sponge black 145*10mm*0.2mm (Acetate cloth) WW M-00010206 R71-M2012-01 1 Stick between fan and radiator 风扇密封醋酸布
73 Sponge black 40mm*6mm*0.2mm (Acetate cloth) WW M-00010207 R71-M2012-02 1 Stick on the main board connector 主板连接器醋酸布
74 Filter black,9*9*0.25mm (Infrared filter) WW M-00010208 R74-M20HW-010 1 红外滤光片
1、Stick between fan and IO board 2、Stick
75 Tape black 35*22*0.1mm (Conductive cloth) WW R71-010935-002 1 风扇与光机FPC对地导电布
M-00010209 on the optical engine connector
76 Tape black 20*10mm*0.1mm (Conductive cloth) WW M-00010210 R71-010920-003 1 Stick on the optical engine FPC 振镜固定导电布
77 Tape black 75*9mm 0.1mm (Conductive cloth VS-E200165 Added on 04/20/2020 M-00010226 R71-010975-002
78 Tape black 50*20mm 0.1mm (Conductive cloth VS-E200165 Added on 04/20/2020 M-00010227 R71-010950-004
79 Packing Material: [Carton, Carton paper box +printing,LOGO:harman/Kardon (color box（WW)) WW VS-E200216 Removed on 04/29/2020 P-00015210 R68-M20001-24Y-ZJ 1 彩盒组件（WW)
Box, Foam, Bags] 350g coated paper T+4C+K,Size:284*150.5*286mm,printing LOGO
80 Carton WW R68-M20001-24Y
“harman/Kardon”（box sleeve） VS-E200216 Added on 04/29/2020 P-00015336
350g ash copper paper+black E120g,printing 4C+7595C,size:289.2*281*146.5mm
81 Carton WW R68-M20002-24Y
（Gift box） VS-E200216 Added on 04/29/2020 P-00015337
350G ash copper paper+printing 4C+black E120g,size:230*227.5*54mm（Internal VS-E200216 Added on 04/29/2020 VS-E200329
82 Carton WW R68-M20005-24Y
box） Removed on 07/17/2020 P-00015338
83 Carton Internal box VS-E200329 Added on 07/17/2020 P-00015504 R68-M20009-24Y
84 Foam internal box foam*4 (Size: 225*47*2mm) VS-E200329 Added on 07/17/2020 P-00015505 R74-M2008-16
350G ash copper paper+printing 4C+black E120g,,size:267*270*80mm（ VS-E200216 Added on 04/29/2020 VS-E200329
85 Carton WW R68-M20006-24Y
Accessories box） Removed on 07/17/2020 P-00015339
86 Carton Accessory box (size: 267*270*74mm) VS-E200329 Added on 07/17/2020 P-00015502 R68-M20010-24Y
87 Foam Top cover foam foam (size: 270*270*5mm VS-E200329 Added on 07/17/2020 P-00015503 R74-M2008-15
88 Carton 250g black cardboard+black E120g,size:267*263mm（Baffle plate with paper） WW VS-E200216 Added on 04/29/2020 P-00015340 R68-M20004-24Y
89 Carton 250G black cardboard,size:269*58.8*21mm（Remote control box） WW VS-E200216 Added on 04/29/2020 P-00015341 R68-M20007-24Y
90 Carton 400g black cardboard,size：266.5*54.4mm（Remote control baffle plate ） WW VS-E200216 Added on 04/29/2020 P-00015342 R68-M20003-24Y
91 Carton paper box +printing,LOGO:JBL (color（VSCN ）) VSCN VS-E200216 Removed on 04/29/2020 P-00015211 R68-M20008-24Y-ZJ 1 彩盒组件（VSCN)
350g coated paper T+4C+K,Size:284*150.5*286mm, printing LOGO “JBL （ ” box
92 Carton VSCN R68-M20008-24Y
sleeve） VS-E200216 Added on 04/29/2020 P-00015335
K=K,paper: 200G,printed in black,bonded molding,size: 602*585*174MM (carton
93 Carton WW R68-M20001-2CY 1 卡通箱
box) P-00015212

Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary item
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versio

Notice: 1. For some special parts, some photos for identification purpose may be asked by reques
2. For all internal cables, there must be some wordings on the "Description" column about where the cable is used (connecting to which two part
3. All internal cables/wires should be put in the "Cables" category
4. All external cables should be put in the "Accessories" category
5. Parts relationship (Main/Second source or 1/2/3/4) should be added in the "Compatibility" column
6. If any part for certain product isn't listed in the form, supplier/PE can add it themselves and keep the part name unified

ViewSonic Corporation 49 Confidential - Do Not Copy M2

 Troubleshooting guide:

Important note: After replacing the main board、Optical Engine 、Focus Board(Webcam

Module),you need to go into factory mode and do the following: horizontal trapezoid correction、
motor auto init、Color coordinate adjustment. Please find and refer to the following section

description: Required Settings after hardware replacement

Especially the Focus Board(Webcam Module),If you do not enter factory mode to operate after the
motor auto init,the autofocus function may fail.

Item Symptom Cause Troubleshooting steps

Plug in the original adapter and power cord,
the projector light is not bright, replace the
Adapter orPower
new adapter and power cord is normal, and
Cord has problems
then replace the adapter and power cord in
turn, to determine whether it is the adapter
problem or the power cord problem.
1 No display
The power Replace Main Board
indicator is red
Check whether optical engine wire
Indicator light isinsertedproperly.(red/green/blue/black).
normal Replace the optical engine
Replace Main Board
Check whether there is a large amount of dust
accumulation in the bottom cover inlet and
Dust accumulation
side outlet of the top cover. If so, open the
in inlet and outlet
bottom cover, and brush gently to cleanwith
dust brush.
Red light wire Check whether the wire of Optical Engineis
loosened firmly inserted (Red light wire )
Auto shutdown
Fan does not work Check whether the connection seat is in good
(High
2 contact.
temperature
Replace Fan
protection)
Replace Main Board
Check whether the Heat Sink copper substrate
and Optical Engine are in good contact,
Heat Sink has whether the screws is loose, touch the copper
problem pipe whether it is not heating, if in good
contact copper pipe is not heating, that heat
sink has problem. Replace Heat Sink
Remote Check whether the battery of remote
Remote controller
3 controldoes not controller without power.
has problem
work Replace the remote controller

ViewSonic Corporation 50 Confidential - Do Not Copy M2

 Check whether thefront and rear remote
Wire connection control both do not work.
Problem Check whether IR Board wire and Main Board
- IO board FPC have buckled firmly
Replace IR board
Partsdefect Replace IO board
The settings To confirm whether the eye protection is
problem enabled in Eye protectionsettings.
Make sure there is no foreign objects shielding
Eye protection Wire connection in front of the lens sensor and the IR board
4
is abnormal wire is well connected
Replace IR board
Partsdefect Replace Main Board

ViewSonic Corporation 51 Confidential - Do Not Copy M2

 Check whether the light coupling wire, the
Wire Connection two wires on the Focus Board are not
problem connected well, and whether the lens camera
5 Blurred image is not blocked by foreign objects

Replace Focus Board

Partsdefect
Replace Optical Engine
Check if the WIFI dongle ispluggedproperly or
WIFI dongle has
Cannot connect not.
problem
6 to WIFI or Replace WIFI dongle
Bluetooth IO board has Replace IO board
problem
Wire connection Check whether the speaker wire seat is
Speaker has no problem plugged in well
7
sound Replace Speaker
Parts defect
ReplaceMain Board
Check whether there is a problem with the
input source of the signal, and whether the
Input source has
interface connection wire is not contacted
problem
well or bad.
Showing
8
abnormal color Wire Connection Check whetherDMDFPC of theOptical Engine is
problem connected firmly, andreconnect again.
ReplaceOptical Engine
Partsdefect Replace Main Board

ViewSonic Corporation 52 Confidential - Do Not Copy M2

 * Reader’s Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.

Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Product General Requirement
2. Block Diagram
3. Disassemble and assemble parts
4. Software upgrade
5. Factory mode
6. Firmware upgrade
7. Panel function description
8. Exploded View and Recommend Spare parts List
9. Troubleshooting Guide

B. Are you satisfied with this Service Manual?

Item Excellent Good Fair Bad
1. Service Manual Content ʳ ʳ ʳ ʳ
2. Service Manual Layout ʳ ʳ ʳ ʳ
3. The form and listing ʳ ʳ ʳ ʳ

C. Do you have any other opinions or suggestions regarding this service manual?

Reader’s basic dada:

Name: ʳ Title: ʳ
Company: ʳ
Add: ʳ
Tel: ʳ Fax: ʳ
E- mail: ʳ
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943.

ViewSonic Corporation 53 Confidential - Do Not Copy M2