HUMIDITY/TEMPERATURE

TRANSMITTER c/w SETPOINT

ADJUSTMENTS
SPC Series

Precision humidity/temperature
control/sensing
FEATURES:
• Dual humidity and temperature outputs
• Humidity and/or temperature setpoint adjustment outputs
• Current and voltage models
• LCD indication
• Highly stable RH sensor element
• Attractive, low profile enclosure
• Installer friendly wiring access

Peace of mind
through reliable
humidity/temperature
monitoring
GREYSTONE HAS AN ISO 9001 REGISTERED QUALITY SYSTEM
DESCRIPTION:
The SPC Temperature/humidity transmitter incorporates two sensors in one attractive wall mount enclosure
for the most efficient environmental monitoring and control system. It uses a field-proven RH sensor to
monitor relative humidity and a curve-matched thermistor to measure temperature.

Two setpoint controls are also available for temperature and humidity adjustment. The device may also
include an occupancy override button and an external communication jack. Both measurements and setpoint
signals are available on separate outputs as linear 4-20 mA, 0-5 or 0-10 Vdc signals.

Several configurations of the device are available with one to four outputs as required. An LCD is included for
configuration and local indication of all parameters. Several operating parameters can be programmed using
a keypad for specific applications including four temperature ranges and C/F display.

SPECIFICATIONS :
General Humidity
Power Supply.............................24Vac/dc ±10% (non- Sensor............................................ Thermoset polymer based capacitive
isolated half-wave rectified) Accuracy....................................... ±2, 3 or 5% RH
Consumption .............................20 mA + (20ma x number of Range............................................ 0 to 100% RH
outputs) max @ 24 Vdc Temperature Compensation. 0˚ to 50˚C (32˚ to 122˚F)
Input Voltage Effect .................Negligible over specified Hysteresis... ................................. ± 3% RH
operating range Response Time........................... 15 seconds typical
Protection Circuitry..................Reverse voltage and MOV Stability......................................... ±1.2% RH typical @ 50% RH in
protected and output limited 5 years
Output Signals...........................4-20 mA active (sourcing) or Offset............................................. ±20% RH programmable
0-5 Vdc or 0-10 Vdc
(specify when ordering) Humidity Setpoint
Output Resolution ...................10 bit for all signals Midpoint...................................... 20 to 70% RH programmable
Output Drive Capability.........550 ohm max for current Range............................................ ±5, ±10 or ± 20% RH of the
10Kohm min for voltage midpoint, programmable
Programming and Selection Via push buttons and Resolution .................................. 1% RH
on-screen menu
Operating Conditions .............0˚-50˚C (32˚-122˚F) 0-95% RH Manual Override
non-condensing
Type .............................................. Front panel, momentary pushbutton
Wiring Connections.................Screw terminal block
Ratings ........................................ 50 mA @12 Vdc, N.O., SPST
(14 to 22 AWG)
Enclosure.....................................White ABS - IP30 (NEMA 1)
Occupied Input
84mmW x 117mmH x 29mmD
(3.3” x 4.6” x 1.15”) Signal Type ................................ Digital input, 0/5 Vdc standard,
active low
LCD Display Action .......................................... Causes “OCC” segment to light on LCD
Display Size.................................38.1 x 16.5 mm (1.5” x 0.65”)
Fan Speed Switch
Digit Height ................................11.43 mm (0.45“)
Symbols .......................................˚C, ˚F, %RH, OCC Type .............................................. Side mounted, 5 position slide switch
Backlight......................................Enable or disable via menu Designators ............................... Off, Auto, Low, Medium, High
Signal ........................................... 2 wire, resistance output - 0, 2, 4, 6, 8 KΩ
Temperature Custom ranges available, contact
Accuracy.......................................± 0.2˚C (±0.4˚F) Greystone
Range............................................0˚ to 35˚C (32˚ to 95˚F) or 0˚ to 50˚C
(32˚ to 122˚F) programmable Communications
Offset ............................................±9˚ F programmable 3.5mm phono jack.................... Ring/Mid/Tip connections to
Display Units ..............................˚C or ˚F programmable a 3-pin terminal block
Display Resolution ...................0.5˚ <100˚, 1˚ >100˚

Temperature Setpoint
Midpoint......................................18˚ to 27˚C or 65˚ to 80˚F
programmable
Range............................................±2 to ±10˚C or ±5 to ±20˚F
of the midpoint, programmable
Resolution ...................................0.5 or 1.0˚C and 1.0 or 2˚F
programmable
PRODUCT ORDERING INFORMATION:
MODEL Product Description
SPC Room Humidity/Temperature Transmitter

CODE Product Parameters

01 Humidity transmitter c/w setpoint control
02 Temperature transmitter c/w setpoint control
04 Humidity and temperature transmitter c/w setpoint control for temperature only
05 Humidity and temperature transmitter c/w setpoint control for humidity only
06 Humidity and temperature transmitter c/w setpoint control for humidity and temperature

CODE Outputs
I 4-20mA
V 0-5Vdc or 0-10 Vdc (Jumper selectable)

CODE RH Accuracy (Not applicable on “02” model, leave blank)

02 2%
03 3%
05 5%

CODE Options (Multiple selections can be made)

S Front panel push button momentary switch (NO)
J External jack for remote system access (3.5 mm phono)
F Fan Speed Switch, 5 position, (Off, Auto, Low, Mid, High)

SPC 06 I 03 S
Greystone Energy Systems, Inc. reserves the right to make design modifications without prior notice.

PCB/WIRING INFORMATION
Terminal Function

POWER From +24 Vac/dc of controller or power supply

COMMON To GND or COMMON of controller
OCC IN To digital output of controller
TEMP Setpoint To analog input of controller
4-20 mA or 0-5 Vdc or 0-10 Vdc
TEMP Output To analog input of controller
4-20 mA or 0-5 Vdc or 0-10 Vdc
DOWN UP SWITCH MENU RH Output To analog input of controller
4-20 mA or 0-5 Vdc or 0-10 Vdc
POWER SWITCH +
RH Setpoint To analog input of controller
COMMON SWITCH -
4-20 mA or 0-5 Vdc or 0-10 Vdc
OCC IN FAN +

TEMP SET FAN -

SWITCH + To digital input of controller
TEMP OUT TIP
SWITCH - To GND or COMMON of controller
RH OUT MID
FAN + To analog input of controller
RH SET RING
Resistance input
FAN - To GND or COMMON of controller
TIP External Jack TIP (tip of plug) connection
MID External Jack MID (middle of plug) connection
RING External Jack RING (base of plug) connection
0001299

* Some models do not have all these features

**To save on number of connection wires, all GND or COMMON may
connected together.
***Illustration shows standard wiring configuration. Custom
configurations are available. Please contact Greystone.
DIMENSIONS:

84 mm 29 mm 58 mm
3.3“ 1.15 “ 2.3 “

119 mm
4.7“ 82.6 mm
3.25 “

12/13
PB-SPC-01-01
Copyright © Greystone Energy Systems Inc. All Rights Reserved
Greystone Energy Systems, Inc. reserves the right to make design modifications without prior notice.

ENERGY SYSTEMS INC Greystone Energy Systems Inc. is one of North America’s
largest ISO registered manufacturers of HVAC/R sensors and
Greystone Energy Systems, Inc. transmitters for Building Automation Management Systems.
We have conscientiously established a worldwide
reputation as an industry leader by maintaining leading-
edge design technology, prompt technical support, and
a commitment to on-time deliveries. We take pride in our
PRINTED IN CANADA

Quality Management System which is ISO 9001 certified,

assuring our customers of consistent product reliability.

GREYSTONE HAS AN ISO 9001 REGISTERED QUALITY SYSTEM