DISPLAY INSTRUCTION FOR LH100

NUMBER 2 COMMUNICATION PROTOCOL

For electric scooter updated 2018/9/18

(we may program it to fit for our controller, please talk to the service person if u

have problem)

1, SIZE AND MATERIAL

Its shell is made of ABS, LCD transparent screen is made of high hardness acrylic, same hard as armored
glass.

this is the install hole diameter

2. working voltage and wiring: DC24V /36V/48V
First is wire which connected
connected with controller
controller,, second is display wire,

1— red –VCC –DISPLAY power wire

2— blue-K-CO
blue-K-CONTROLLER
NTROLLER power control wire
3— black-GND-Display
black-GND-Display ground wire
4— green-RX-display data receive wire
5— yellow-TX-DISPLAY data sending wire

3. Function introduction

indicate this after 1 second when u open the machine

3.1 Indicate speed, battery level, error code, odometer, single trip
3.2 Can Control, set this functions bellow
Power lock/electric switch, rim size, auto sleeping time, backlight lightness, start way , driven way,
way, voltage, controller current,
USB charging
3.3 communication protocol : UART

this is voltage condition grade

this is multifunction indication area, ODO, TRIP, voltage .

speed unit MPH, KM/H

Speed signal: takes from motor inside hall signal. send to display through controller, (single hall cyle
period, unit 1MS.) display will count to real speed according to rim size and signal data, (motor hall need to
set magnetic steel number).

vehicle pedal gears adjustable,

adjustable, 0-9gears
 zero start and non zero start

frontlight cruise error usb charging

Bellow is error code

Error code Error condition remark

0 Normal work
1 no
2 Brake
3 Pas sensor error (riding icon) No here
4 6KM/H cruise
5 Timely cruise
6 Battery undervoltage
7 Motor error
8 Throttle error
9 Controller error
10 Communication receive error
11 Communication send error
12 BMS Communication error
13 Frontlight error

4. Setting
P01：backlight lightness, 1 is most dark, 3 is most light,
P02：set range unit，0：KM；1：MILE；
P03：voltage ：24V/36V/48V/60v ，default setting : 36V；
P04：sleeping time：0-no sleep；other number means sleeping time，scope：1-60；unit in
minute；
P05：pedal gears : 0： 3gears mode；
P06: rim size ：unit ，inch；precision：0.1；
P07: speed testing magnetic steel number ：scope：0-255；
P08：speed limit：scope 0-100km/h，(did not open this )
P09：zero start/non-zero start，0：zero start；1：non-zero start；
P10：driven way set
0 : pedal drive: pedal gears will decide how many pedal power to output.now the throttle will not work
1 : electricity: driven by throttle, now pedal donot work
2 : both pedal and throttle will wor (zero start will not work under electricity mode)
1：pedal sensitivity (donot open)
P11
P1
P12：pedal strength set (unopened)
P13：pedal magnetic sensor set 5/8/12
P14：controller current limit set, default setting 13A scope：1-20A
：
P15 controller under voltage set
P16: ODO zero
zero clear set , long press for 5 seconds,
seconds, ODO
ODO come to zero
P17：0：no cruise，1：can cruise；
auto cruise available only for number 2 communication protocol
 P18：indicating speed ratio set, scope：50%~150%，
P19：0 available or not ，0：with 0 gear，1：no 0 gear
P20：0: 2 number protocol 1: 5S protocol 2：standby 3：standby

5, button and interfa

interface
ce introducti on

achine open passcode interface

S S1 

1、MACHINE off, long press to open it；then

hen short
ort press
ess the inter
erfface will
ill swit
switcch bet
betwee
een
n

ODO/TRIP/VOL.

2、wh
when
en mac
achi
hine
ne ope
open, long
long pres
presss to turn
urn ma hine off，short press MODE button can switch
macchine

GEAR

3、long press + will go

go iin
nto pa
passcode an
and ma
manual se
set an
and cch
hoos
ose
e in
interface S
S0.
0. Under S0, short

press b utton can switch passcode digit, . Short press button can change numbers,

3.1 input “1111”then long press will go into S1, short press switch passcode digit，

short pr
short press
ess button
button will
will change
change curren
currentt number
number.. After
After finish
finish pass
pass co
code
de settin
setting,
g, lon
long
g press
press will
will
exit S1interface and back to normal and will store the passcode you set.（attention please: next time if need
to open, need input this pass code, please remember it. If u set it 0000, means no passcode, u will go directly
into normal interface when open the machin ） 。

3.2 input “6666”th

then
en long
long pres
presss butt
button
on will
will g
go
o into
into se
sett
ttin
ing
g int
inter
erfa
face
ce.. .un
.under
der any
any d
dat
ata,
a, shor
shortt

press to switch data，short

ort pr
press
ess or
or llo
ong press
ess but
button add
add or
or re
reduce data（long press
duce dat will

change direction of the number changing ，left indicate “A”means add，left indicate“d”means reduce），

after
after chan
change,
ge, short
short pr
press
ess will
will swit
switch
ch to next
next dat
data
a and
and stor
store..
e.. after
after settin
setting
g plea
please
se long
long press
press +

to store and exit setting interface ，or wait 8seconds, it will exit automatically and store data.
 4、crank adjust motor rpm, from up to down, rpm add, release , it will return to zero.

5. standby “3745”passcode operation

If u forget your pass code, please input “3745”, -this is a standby passcode ， long press 10seconds,

it will go into normal interface.

6. about its controller

controller
For dual mode controller 6/9/12/15/18/24 mosfet.
Please connect display and controller together and set display right when u first get this group, connect controller right
with battery positive and negative, and use self learning wire to match controller phase and hall sensor wire well with
those of motors. U will have less problem .

Power positive negative pole

Connect with battery positive and negative output (please donot make it oppositely),

Motor phase wire and hall connector

WAY 2
USE self learning function intelligent
intelligently
ly identify motor phase and
a nd turning direction

Connect power, motor phase wire, hall wire, electric switch, rolling handlebar /throttle wire, learning wire, make sure it is
right and turn power on, motor runs automatically
automatically.. If direction right, then cut off learning wire after 2-3seconds, this finished
the learning.
If motor turns in opposite direction, then cut off learning wire, and connect on immediately or using handlebar, motor
change to right direction automatically.
automatically. Cut off learning wire after motor running 2-3seconds, this finished learning.
Using Learning wire only in connecting period, when finished wiring, cut off it, you need not connect it.
For 350w controller sine wave controller , No self learning wire, u need match motor phase wire and hallsensor wire with
those of controllers’ by hand., (it need motor with hallsensor). Donot suggest this model if u are new learner
Way 1: match the phase (for each way, after test should reset)
Keep hall wire A unchanged, change the connecting way of controller and motor phase wire(6way
w ire(6ways)
s)
1. Color match (yellow for yellow,
yellow, green for green, blue for blue) -this has one method
2. Make one stagger (2 keep yellow for yellow and switch blue and green)-this has 3 ways)
(3keep green for green, switch blue and yellow)(4keep blue for blue exchange yellow and green)
3. Stagger all colors (5. Yellow connect blue, green with yellow,
yellow, blue for green )--this has 2 method (6 yellow for green, green
for blue, blue for yellow )
Exchange blue and yellow on hall B wire, then copy the six connecting way above
The right phase: motor runs with clear sound, no-load current 0.8-2A
Bellow is the link to order this group 350w
https://www.aliexpress.com/item/LCD-display-white-screen-and-colored-scrreen-with-shifter-controller-for-electric-
bike-scooter-24v36v48v60v-250w350w/32840331092.html
here is the link from 350w-1000w
https://www.aliexpress.com/store/product/24v36v48v-400W-1000W-BLDC-controller-LCD-display-with-throttle-blue-
screen-or-colored-screen-electric-
scooter/2802219_32793593953.html?spm=2114.10010108.1000023.1.799c6619AzL2hZ
here is 1500-3000w display+controller
https://www.aliexpress.com/store/product/24v36v48v60v-1500w-3000W-BLDC-controller-LCD-display-with-throttle-
shifter-white-colored-screen-electric-scooter-
MTB/2802219_32877096954.html?spm=2114.12010612.8148356.32.713247acjiWTpi
for motor hallsensor wire
Motor hall
1. Red-+5v
2. White external speed test(some controller has no this wire)
3. Black-ground
Black-ground wire
4. Yellow-hall A
5. Green-hall B
6. BLUE-HALL C
Controller size and weight grow due to its power, such as

6mosfet controller 88*52*30mm

9mosfet controller 110*85*45mm
12mosfet controller 145*85*45mm
15mosfet controller 176*85*45mm
18mosfet controller 170*108*58mm
24mosfet controller 225*125*75mm
For other function of controller please check the link.

WE may update the display setting and controller wiring, if what u get is different from the online introduction or u have
any question please leave message to us. We have the right to explain it.

PHOEBE EV PARTS AND TOOLS STORE

Our shop on aliexpress: https://www.aliexpress.com/store/2802219

Email: [email protected] , [email protected] , [email protected]

Paypal: [email protected]
whatsapp/wechat/telephone:
whatsapp/wechat/telephone: 136986165
13698616511
11
Address for return/ repair: room403, building 26, 94nong, yongye road, jinqiao town, pudong district, shanghai, china.
Post code: 201206