Scribd
Upload
20 views5 pages

Sample 1

The document is an examination paper for the course ECE200/EEE201: Electrical Circuits I, consisting of 7 questions across 5 pages. Students are required to answer any six questions, with various circuit analysis techniques such as mesh analysis, superposition, and Delta/Wye conversion being tested. The exam covers topics including power absorption, load resistance for maximum power transfer, RL and RC circuit analysis, and magnetic flux calculations.

Uploaded by

Tanvir Ayad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
20 views5 pages

Sample 1

The document is an examination paper for the course ECE200/EEE201: Electrical Circuits I, consisting of 7 questions across 5 pages. Students are required to answer any six questions, with various circuit analysis techniques such as mesh analysis, superposition, and Delta/Wye conversion being tested. The exam covers topics including power absorption, load resistance for maximum power transfer, RL and RC circuit analysis, and magnetic flux calculations.

Uploaded by

Tanvir Ayad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

No.

of Pages 5
No. of Questions 7

Department of Electrical & Electronic Engineering


FINAL EXAMINATION SUMMER 2012
ECE200/EEE201: Electrical Circuits I
Total Marks: 120 Time Allowed: 3 Hours

• Answer any Six (6) questions.


• Figure in bracket [] next to each question indicates marks for that question.
• Draw each of the Figures in the answer script and label accordingly.
• Understanding question is part of the exam.

Question No. 1

a) In the circuit of Figure 1.a, find the power absorbed by each of the five
elements in the circuit and prove that the total power delivered is equal to the
total power absorbed. [10 marks]

Figure 1.a: Circuit network for question no. 1.a

b) For the circuit of Figure 1.b, compute the voltage across each current source
using node analysis. [10 marks]

Figure 1.b: Circuit for question no. 1.b


Question No. 2

a) Find out the current through the 11 ohm resistance of the network shown in
Figure 2.a by mesh analysis. [10 Marks]

Figure 2.a: Circuit for question no. 2.a

b) Employ Delta/Wye convertion technique to find out the source current for the
for the network shown in Figure 2.b. [10 Marks]

Figure 2.b: Circuit for question no. 2.b

Question No. 3

a) Use the principle of superposition to find out v0 in Figure 3.a.


[10 marks]

Figure 3.a: Circuit for question no. 3.a

Page 2 of 5
b) In Figure 3.b, use repeated source transformation to find out the current i0.
[10 marks]

Figure 3.b: Circuit for question no. 3.b

Question No. 4

Choose a load resistance to be connected at the terminal a-b so that maximum power will
transfer to it from the network shown in Figure 4 and also calculate the maximum power
absorbed by the load.

[20 marks]

Figure 4: Circuit for question no. 4

Page 3 of 5
Question No. 5

The switch S1 of Figure 5 has been closed for a long time. At t=0sec, S1 is opened, at
the same instance S2 is closed.
a) Find the initial current through the coil
b) Find the mathematical expression for the current (iL) through the inductor and
corresponding voltage (vL) following the closing of the switch S2.
c) Sketch the waveform for iL and vL.
[ 20 marks]

Figure 5: RL circuit network for question no.5

Question No. 6

For the network of Figure 6,


a) find the mathematical expression of vc and ic following the closing of the switch
at t=0 sec.
b) find the mathematical expression of vc and ic if the switch is thrown into position
2 at t= 9ms.
c) sketch the waveforms of part (a) and (b) on the same time axis.
[ 20 marks]

Figure 6: RC circuit network for question no.6

Page 4 of 5
Question No. 7

Find the magnetic flux established in the magnetic circuit shown in Figure 7. Error up to
±5% is acceptable. The core is made of cast steel. The parameters for the core are given
below:
[ 20 marks]
𝑙𝑙𝑐𝑐𝑐𝑐 = 7 × 10−4 𝑚𝑚
𝑙𝑙𝑎𝑎𝑎𝑎 = 𝑙𝑙𝑏𝑏𝑏𝑏 = 𝑙𝑙𝑒𝑒𝑒𝑒 = 𝑙𝑙𝑓𝑓𝑓𝑓 = 0.25𝑚𝑚
𝐴𝐴𝐴𝐴𝐴𝐴𝐴𝐴 (𝑡𝑡ℎ𝑟𝑟𝑟𝑟𝑟𝑟𝑟𝑟ℎ𝑜𝑜𝑜𝑜𝑜𝑜) = 2.5 × 10−4 𝑚𝑚2
𝑙𝑙𝑏𝑏𝑏𝑏 = 𝑙𝑙𝑑𝑑𝑑𝑑

Figure 7: Magnetic circuit for the question no.7

B-H Curve for Question No. 7

Page 5 of 5

You might also like