[ 1] 20102011 [int]: turn on the Uart logs.

[ 2] 22KHZ [int]: Set 22KHz test state ( 0:off, 1:on) (22KHZ n) - int

[ 3] AACAUDPID [int]: Set AAC audio pid (AUDPID n)

[ 4] AACSUPPORT [int]: ex: AACSUPPORT 1

[ 5] AC3AUDPID [int]: Set AC3 audio pid (AUDPID n)

[ 6] ACF_ENABLE [str]: Enable or Disable a layer

[ 7] ACF_HELP: Display available help.

[ 8] ACF_INFO: Print layers information

[ 9] ACF_LAYERS: Print layers

[10] ACF_ROTATE [int]: Rotate layers

[11] ACF_STATE [int]: Set Test layer State

[12] ACTIVECHANNELLIST: Gets active channel list

[13] ACTIVECHLIST [int]: show channel list

[14] ACTIVEMODEPIPPAP_ONOFF [int]: changes values of the PIP and PAP (0:off, 1:pip, 2:pap)

[15] ADCCAL [int]: start ADC auto calibration (ADCCAL source) (0:SCART-RGB, 1:YPbPr, 2:PC/VGA)

[16] ADDSERVICES: Adds hardcoded services to service list

[17] ADD_ALLFAVOR [int]: Adds whole channels to the favourite channel list

[18] ADD_FAVOR [str] [int]: Adds a channel to the favourite channel list

[19] ADD_TIMER [str]: Add timer for a service

[20] ASPECT [int]: Set aspect ratio: 0 for 4:3 TV, 1 for 16:9

[21] ASSERT: Force ASSERT failure - stops lku & enters debugger

[22] ATOF [int]: Set auto tv off level (AUTOTVOFF n)

[23] AUDIODESC [int]: Set audio description state (AUDIODESC n)

[24] AUDOFF: Select audio off

[25] AUDON: Select audio on

[26] AUTOPOS: Set auto position

[27] AUTOTVOFF [int]: Set auto tv off level (AUTOTVOFF n)

[28] AUTOTVOFF2MINUTES: Start periodic auto tv off check for 2 minutes (AUTOTVOFF2MINUTES)
[29] AUXFSREAD [str]: Initiate reading file from auxiliary filesystem (CI://...)

[30] BACKLIGHTDIM [str] [int]: Set backlight dimming level(values are low, high, off (if enabled
from profile)) (BACKLIGHT string)

[31] BLUEBACK [int]: Set bluebackground state (BLUEBACK n)

[32] BRIGHTNESSDOWN: Decrease Brightness Level by 1 step

[33] BRIGHTNESSUP: Inrease Brightness Level by 1 step

[34] BROADCAST [int]: set broadcast type

[35] BUILDINFO: Reports the build info

[36] CA [str] [int]: Conditional access <command> <parameter>

[37] CANCELAPS: cancel auto search if there is any started auto search (CANCELAPS)

[38] CAPTURE [int]: Capture plane to file 0-10

[39] CARPODWN1: Start the web search for forced software update and verify in RAM if exists

[40] CARPODWN2: Start the web search for forced software update and burn flash if exists

[41] CARPOSTOP: Stop the web search for software update

[42] CHANGELNG [str] [int]: change active language

[43] CHANNEL [int]: Tune to specified channel number (CHANNEL n)

[44] CHILDLOCK [int]: set child lock mode

[45] CICAMPLAYERCONTROL [str] [int]: Control CICAM Player param:lts_id=71, command=01, ...
msg:1-player_stop/2-info_req/3-control_req

[46] CICAMPLAYERCONTROLHOSTMODE [str] [int]: Control CICAM Host Player mode

param:service_loc=hexBytes, ... msg:5-play_req

[47] CLEANUSB [str] [int]: Remove files in usb

[48] CLEARBROWSERDATA: Clears whole browser data

[49] CLEARCACHE: Clears browser data

[50] CLEARCHLIST: clear all the channels

[51] CLEARDSMCCNVMCACHE: Clear the DSMCC NVM cache

[52] CLEARPRIVATEDATA: Clears private data

[53] CLEARPROXY: Clears proxy is used

[54] CLEARSTATS: Clear statistics

[55] CLOSESVGRC: Close SVG RC

[56] COLOURTEMP [str] [int]: set colour temperature (values are normal, warm, cool)
(COLOURTEMP string)

[57] CONTRASTDOWN: Decrease Contrast Level by 1 step

[58] CONTRASTUP: Inrease Contrast Level by 1 step

[59] CONVERSION [int]: Set AR conversion: 0 - CCO, 1 - letterbox

[60] CREATEAPP [str]: creates a new application

[61] CTZ [int]: Change Time Zone

[62] DBOOTC: Disable Bootcaster

[63] DDHCPC: Disable Dhcp client

[64] DECOWB [str] [int]: decrement osd white balance value by n (DECOWB type n
(type:redgain,greengain,bluegain,brightness n:0-255))

[65] DECWB [str] [int]: decrement white balance value by n (DECWB type n
(type:redgain,greengain,bluegain,redoffset,greenoffset,blueoffset n:0-255))

[66] DEFAULTZOOM [str] [int]: set default zoom mode (values are 4:3, 16:9, 14:9) (DEFAULTZOOM
string)

[67] DELETECHANNEL [int]: deletes the channel which has been entered

[68] DELETEHOSTNAME: Delete Hostname

[69] DELETE_ALLFAVOR: Deletes whole channels from the favourite channel list

[70] DELETE_FAVOR [str] [int]: Delete a channel to the favourite channel list

[71] DELETE_TIMER [str]: delete timer

[72] DELREMINDERS: Delete all reminders in the system

[73] DISABLECACHE: Disable browser disk caching mechanism

[74] DISPLAYCOLLECTEDEITDATACOUNT: display collected EIT data count

[75] DOTCLOCK [int]: Set dot clock (DOTCLOCK n)

[76] DOWNLOADFILETOTMP [str]: Downloads the file from given path

[77] DRMDEACTIVATIONCODE: Gets DRM deactivation code

[78] DRMREGISTRATIONCODE: Gets DRM registration code

[79] DTSSUPPORT [int]: ex: DTSSUPPORT 1

[80] DUMPLAUNCHERITEMS: Dumps all launcher items

[81] DUMPPORTALURLITEMS: Dumps all portal url items

[82] DUMPREMINFO: Dump reminder info

[83] DUMPSL: Dump internal service list

[84] DVRUSBSPEEDTEST: Test result of usb speed

[85] EBOOTC: Enable Bootcaster

[86] EDHCPC: Enable Dhcp client

[87] ENERGYSAVING [str] [int]: Set energy saving mode (values are off, minimum, medium,
maximum, auto, screen_of (if enabled from profile)) (ENERGYSAVING string)

[88] ENTERACTIVESTANDBY: Enter Active Standby

[89] EVENTCACHE [int]: Event cache enable/disable (EVENTCACHE 0=off 1=on)

[90] EXITACTIVESTANDBY: Exit Active Standby

[91] FACTORY: Load factory settings to NVRAM

[92] FAKE_STANDBY_MODE: changes standby value

[93] FEATUREOSDPAUSE: Feature osd refresh timer paused

[94] FEATUREOSDPLAY: Feature osd refresh timer started

[95] FREEZE: freeze/unfreeze (FREEZE)

[96] FSU: forceWebUpdate

[97] FTP2USB [str]: Get Update files from ftp to usb

[98] FTP2USBCONFIG [str]: Get update configuration files from ftp to usb

[99] GETAPPLIST [str]: Get the applications on home or apps or market. Usage: GETAPPLIST (home
- apps - market) ,Example : GETAPPLIST home

[100] GETAUTOTVOFF: Get auto tv off mode

[101] GETAVL: get AVL state

[102] GETBACKLIGHT: Get backlight level

[103] GETBACKLIGHTDIM: Get backlight dimming level

[104] GETBALANCE: get balance value

[105] GETBASSGAIN: get bass gain level

[106] GETBLUESTRECH: get bluestrech value

[107] GETBRIGHTNESS: get picture brightness value

[108] GETBRIGHTNESSLIMITS: get picture brightness limits

[109] GETCHANNELINFO [str] [int]: Print the channels parameters

[110] GETCHANNELLIST: Gets the result of channel table

[111] GETCHANNELLISTVIEW: Gets the result of channel list view table

[112] GETCOLOUR: get picture colour value

[113] GETCOLOURSHIFT: get colour shift value (GETCOLOURSHIFT)

[114] GETCOLOURTEMP: get colour temperature (GETCOLOURTEMP)

[115] GETCONFIG [str]: sets registration ID to PubSub instance (GETCONFIG

brand,mainboard,country,panel,tv_time)

[116] GETCONTENTRES: Get content resolution

[117] GETCONTRAST: get picture contrast value

[118] GETCOUNTRY: get country in channels state

[119] GETCURRENTANALOGTVSYSTEM: get current analog tv system value

[120] GETCURRENTCHANNEL: Gets the result of current channel

[121] GETCURSORPOSITION: gets cursor position in the browser

[122] GETDAPMODE: get DAP mode

[123] GETDEFAULTGATEWAY: get default gateway (eg. GETDEFAULTGATEWAY)

[124] GETDEVICEID: prints device ID assigned for extended logging

[125] GETDIGITALOUT: get digital out

[126] GETDNS1: get DNS server 1 (eg. GETDNS1)

[127] GETDNS2: get DNS server 2 (eg. GETDNS2)

[128] GETDNSCONFIGURATION: get DNS configuration mode (auto,manual) (eg.

GETDNSCONFIGURATION)

[129] GETDYNAMICBASS: get dynamic bass value

[130] GETDYNAMICCONTRAST: Get Dynamic Contrast Level

[131] GETENERGYSAVING: Get energy saving mode (if enabled from profile))

[132] GETEPGSTATUS: returns status of EPG (ON or OFF)

[133] GETEQMODE: set equalizer mode

[134] GETEQUSERFREQ [str]: get equalizer user freq. value for any band (GETEQUSERFREQ band)

[135] GETESNID: Reads Netflix ESNID from SPI

[136] GETFILMMODE: Get film mode (GETFILMMODE)

[137] GETFIXEDPICTUREMODE: get Picture Mode availability (ON, OFF)

[138] GETHDMITRUEBLACK: Get hdmitrueblack state (GETHDMITRUEBLACK)

[139] GETHEADPHONEOUTPUT: Get headphone output

[140] GETHEADPHONEVOLUME: Get headphone volume level

[141] GETHIGHLIGHTEDCHANNEL: Gets the result of highlighted channel

[142] GETHOSTNAME: Get Hostname

[143] GETHOTELMODE: Get hotel mode

[144] GETINFO [str]: called from client connected to TCP_TESTTOOL_SERVER_PORT

[145] GETLANGUAGE: Shows the language

[146] GETLASTRFUPDATECOMPLETE: Gets last rf update complete time

[147] GETLOGCONFIG: prints extended logging configuration

[148] GETMAXVOLUME: get volume maximum level in Hotelmode (VOLUME n)

[149] GETMAXVOLUME: get volume maximum level in Hotelmode (VOLUME n)

[150] GETMBSUBTFONTSIZE: returns media browser subtitle size n (56,63,67,74,81)

[151] GETMBSUBTLANG: returns subtitle language

[152] GETMBSUBTPOS: returns subtitle position (up or down)

[153] GETMENUTIMEOUT: Get menu time out mode

[154] GETMHEGINFO: Get Mheg Information

[155] GETMICRODIMMING: Get Micro Dimming Level

[156] GETMINVOLUME: get minimum volume level in Hotelmode

[157] GETMODELNO: ex: GETMODELNO

[158] GETMUTE: get mute value on/off

[159] GETNETWORKTYPE: get network type (eg. GETNETWORKTYPE)

[160] GETNEWREGISTRATIONID [str]: gets new registration ID from PubSub server

(GETNEWREGISTRATIONID
brand,mainboard,country,panel,speaker,mp_profile,buyer,sw_version,tv_time)

[161] GETNOISEREDUCTION: Get noise reduction state (GETNOISEREDUCTION)

[162] GETOWB [str] [int]: get osd white balance value(GETOWB type)
(type:redgain,greengain,bluegain,brightness)

[163] GETPANELLOCK: get Panel Lock availability (ON, OFF)

[164] GETPATTERN: Get selected pattern of the TV screen (GETPATTERN)

[165] GETPICTUREMODE: get picture mode

[166] GETPICTUREZOOM: Get picture zoom mode (GETPICTUREZOOM)

[167] GETPORTALMODE: Gets tv is portal mode or not

[168] GETPOWERSAVE: Get power save mode (GETPOWERSAVE)

[169] GETPROFILEINFO: Print Profile Name Information (ex:GETPROFILEINFO)

[170] GETPROGRAM: get program

[171] GETPROXY: Clears proxy is used

[172] GETQUICKSTANDBY: Quick Standby is n, where n is one of (off, on)

[173] GETQUICKSTANDBYOPTION: gets quick standby option

[174] GETRC: Get remote control commands enabled status

[175] GETRCU: Get RCU Inhibit

[176] GETRDSERVERURL: get remote diagnostic server url

[177] GETSDRTOHDR: get sdr to hdr value

[178] GETSERIALNO: ex: GETSERIALNO

[179] GETSHARPNESS: get picture sharpness value

[180] GETSKINTONE: Get picture skin tone value

[181] GETSLIDESHOWINTERVAL: returns slide show interval n seconds(5,10,15,20,25,30)

[182] GETSOUNDOUTPUT: Get sound output

[183] GETSOURCE: Gets source

[184] GETSPECIALPORTALAPPS: Gets portal specific portal applications' statuses

[185] GETSTANDBY: get standby on/off

[186] GETSTARTUPMODE: get startup mode which is in hotelmode Last Status(Standby, ON,
LastStatus)

[187] GETSTARTUPSOURCE: get startup source in hotelmode(0-15)

[188] GETSTARTURL: Get Start URL

[189] GETSTARTVOLUME: get startup volume in Hotelmode (VOLUME n)

[190] GETSUBNETMASK: get subnet mask (eg. GETSUBNETMASK)

[191] GETSWPROFILEVERSION: gets sw profile version

[192] GETSWVERSION: Returns the software version of tv, ex: GETSWVERSION

[193] GETTELNET: Get Telnet support

[194] GETTIMEMODE: Get time mode auto/manual

[195] GETTIMESHIFTURL: get follow tv url

[196] GETTVINFO: ex: GETTVINFO

[197] GETTVLIFETIME: ex: GETTVLIFETIME

[198] GETUINAME: ex: GETUINAME

[199] GETURL: Gets URL of the current page if the portal is active

[200] GETUSBAUTOPLAY: returns usb autoplay status (ON or OFF)

[201] GETUSBOPTION: get USB Option (ON, OFF, 5V)

[202] GETUSERAGENT: Gets portal user agent

[203] GETVIDSTATE: Get video state

[204] GETVOLUME: get volume level

[205] GETWB [str] [int]: get white balance value(GETWB type)

(type:redgain,greengain,bluegain,redoffset,greenoffset,blueoffset)

[206] GETWIFIAPCHANNEL: returns the channel of the wifi access point

[207] GETWIFIAPSECURITYPASSWORD: returns the password of access point

[208] GETWIFIAPSECURITYTYPE: returns the security type of access point

[209] GETWIFIAPSSID: returns the SSID of access point

[210] GETWIFIAPSTATE: returns the access point state

[211] GETWIFIAPTXPOWER: returns TX Power for wifi access point

[212] GETWIFIINFO: gets wifi information (extended logging)

[213] GET_SW_VER: Returns the software version of tv, ex: GET_SW_VER

[214] GMP: Get MHEG profile

[215] GOFIRSTITEM: Goes to first item of a cyclic SVG item such as selection box.

[216] GOFIRSTITEMGROUP: Goes to first item of a cyclic SVG item such as menu, list box etc.

[217] GOLASTITEMGROUP: Goes to last item of a cyclic SVG item such as menu, list box etc.

[218] GSEARCH [str]: Starts Global Search with given string

[219] GTCURL: Get Channel List URL

[220] GTFTP: Get FTP Properties

[221] GTNTP: Get NTP Server IP

[222] GTSURL: Get TV Portal URL

[223] GTZ: Get Time Zone

[224] GWOL: Get Wake on Lan

[225] GetUEP: Get Universal Engine Profile

[226] GetWhoAmI: Get Who Am I String

[227] H264VIDPID [int]: Set H264 video pid (H264VIDPID n)

[228] HARDOFHEARING [int]: Set hard of hearing state (HARDOFHEARING n)

[229] HEADPHONEHOTPLUG [str] [int]: Set headphone hotplug (values are ON, OFF)
(HEADPHONEHOTPLUG string)

[230] HEADPHONEVOLUME [int]: Set headphone volume level (HEADPHONEVOLUME n)

[231] HPOS [int]: Set horizontal position (HPOS n)

[232] HTMLUICACHED [int]: set the flag if the HtmlUI files are cached or not (bool)

[233] HTTPSREQ [str]: Conduct a https request

[234] IMGHIDE: Hide image file (IMGHIDE)

[235] IMGSHOW [str] [int]: Show image file (IMGSHOW /media/sda1/picture.jpg)

[236] INCOWB [str] [int]: increment osd white balance value by n (INCOWB type n
(type:redgain,greengain,bluegain,brightness n:0-255))

[237] INCSWUPDATECOUNTERS [int]: Increase software update counters parameters: 0- USB

UPDATE 1-HTTP_UPDATE 2-SIDE_LOAD_USB_UPDATE ex: INCSWUPDATECOUNTERS 1

[238] INCWB [str] [int]: increment white balance value by n (INCWB type n
(type:redgain,greengain,bluegain,redoffset,greenoffset,blueoffset n:0-255))

[239] INITWEBMESSAGE [str]: Enable/Disable Web Message - Use url as argument to enable,
'disable' to disable

[240] INSTALLANALOGCHANNEL [int]: start analog manual search with only frequency parameters
frequency:int(Khz value) (INSTALLANALOGCHANNEL frequency) -int

[241] ISPRPROTECTED: Checks whether playing video is protected by PlayReady

[242] ISVIDEOSHOWING: Check if there is a video shown on the screen or not

[243] IS_FAVOR [str] [int]: Whether a channel is in the given numbered favourite channel list
(IS_FAVOR channel fav_number)

[244] KEY [str] [int]: Send key to Eclipse (KEY name)

[245] KPLAY: Play Key Sequence

[246] KSET [str] [int]: Set Key Sequence

[247] KSTOP: Stop Key Sequence

[248] LISTPR: lists all programs in program list

[249] LNB [int]: Set LNB Voltage state ( 0:off, 1:V-13V,2:H-18V) (LNB n) - int

[250] Led [int]: Turns the led on/off. Ex: Led X (X: state -> 0: OFF, 1:ON)

[251] MAINMENUITEM [str] [int]: select main menu item, valid values are : picture, sound,
settings, installation, channellist, mediabrowser

[252] MENUTIMEOUT [int]: Set menu time out mode (MENUTIMEOUT n)

[253] MHEG [int]: Turn mheg on/off

[254] MP3PLAY [str] [int]: Play MP3 audio file (MP3PLAY /mnt/hd0a/audio.mp3)

[255] MP3STOP: Stop MP3 audio file (MP3STOP)

[256] MPEG2AUDPID [int]: Set MPEG-2 audio pid (AUDPID n)

[257] MPEG2VIDPID [int]: Set MPEG2 video pid (MPEG2VIDPID n)

[258] MS11SUPPORT [int]: ex: MS11SUPPORT 1

[259] MVCSUPPORT [int]: ex: MVCSUPPORT 1

[260] NETCLONE [str]: Clone from FTP server, example: NETCLONE <ip-of-server/path>

[261] NETWRKCHGTIMES [str] [int]: Select 90 second - 2 day warning, 30 second 1 hour warning

[262] NOWFILTER [int]: Set now&next event update filter (NOWFILTER lcn/handle)

[263] NVDS_SIZE [str] [int]: Memory usage of a client (or all clients) - str-int

[264] OMEDB: OpenMedia Browser

[265] OPENDLNASERVER [str]: Opens given DLNA server. Ex: OPENDLNASERVER dlna_server_name

[266] OPENURL [str]: Starts the given URL and returns web page load status directly

[267] OSD_PRINT [str] [int]: Prints an osd in x-y position with the string entered in it (OSD_PRINT X-
Y-string)

[268] PATTERN [str] [int]: Set TV screen to selected pattern (values are WHITE, RED, GREEN, BLUE,
MAGENTA, CYAN, YELLOW) (PATTERN string)

[269] PCRPID [int]: Set PCR pid (PCRPID n)

[270] PHASE [int]: Set phase (PHASE n)

[271] PICTUREMODE [int]: select picture mode (1:dynamic 2:natural 3:cinema 4:game)
(PICTUREMODE value)

[272] PICTURERESET: reset picture settings (PICTURERESET)

[273] PICTUREZOOM [str] [int]: set picture zoom mode (values are auto, 16:9, subtitle, 14:9,
14:9zoom, 4:3, full(only for HD channels), cinema) (PICTUREZOOM string)

[274] PIP [int]: PIP on/off (PIP 0=off 1=on)

[275] PIPSERVICE [int]: Select PIP Service (PIPSERVICE lcn/handle)

[276] POWERSAVE [str] [int]: Set power save mode (ON/OFF) (POWERSAVE string)

[277] PRINTALLPROFILE: Prints hw, sw and dev profile values

[278] PRINTDEVPROFILE: Prints dev profile values

[279] PRINTHWPROFILE: Prints hw profile values

[280] PRINTMENUNAVIGATIONLIST: prints menu navigation list (extended logging)

[281] PRINTRCUSAGELIST: prints rc usage list (extended logging)

[282] PRINTSWPROFILE: Prints sw profile values

[283] PRINTSWUPDATECOUNTERS: Print software update counters

[284] PRINTTVSTATE: Print last tv state, result of last channel opening request. Prints 'OK', 'No
signal', 'No service', 'No video', 'Scrambled service', Usage: GETDIALOGNAME

[285] PUBLISHMESSAGETOANYTOPIC [str]: publish message to any PubSub topic.

(PUBLISHMESSAGETOANYTOPIC topic_name,param1,param2,param3,...)

[286] RDCONN [str] [int]: Connect a removable device read or read/write (RDCONN "r"/"rw")

[287] RDDIS: Disconnect a removable device (as set by RDCONN)

[288] READMODEPIPPAP_ONOFF: returns the PIP and PAP values

[289] REMSET [str] [int]: Set a reminder (REMSET "service handle/lcn, date(DD/MM/YYYY),
time(HH:MM), duration(minutes)"

[290] REPEATOFF [int]: Set the remote control auto repeat off for ice key n (REPEATOFF n)

[291] REPEATON [int]: Set the remote control auto repeat on for ice key n (REPEATON n)

[292] RESET: Reset the box

[293] RESETDEVICEID: resets device ID assigned for extended logging

[294] RESETMAINMENU: Reset TV main menu, Home and Apps categories

[295] RESUP: Update resource manager

[296] RFSIGNALOFF: deactivate the valid signal

[297] RFSIGNALON: activate the valid signal

[298] RST: Restart TV

[299] RTCSET [int]: Set/Query RTC clock

[300] RTCTEST: Perform RTC clock test

[301] RTVP: Return TV Main Page

[302] SAVEWIFIPROFILE [str]: Save access point to wifi_profile.Parameters: ssid key

[303] SCAN: Do Scan

[304] SCHEDFILTER [int]: Set schedule event update filter (SCHEDFILTER lcn/handle)

[305] SCURL [str] [int]: Set Channel List URL

[306] SDFTI: Set Default FirstTimeInstallation

[307] SEA [str]: Send emergency alarm

[308] SELECTSOURCE [int]: select source (0=TV, other source indexes(some of them are not
enabled)) (SELECTSOURCE n)

[309] SERVICE [int]: Select Service (SERVICE lcn/handle) (use SERVICE 0 to deselect service)

[310] SETAVL [int]: set AVL state (SETAVL n)

[311] SETBACKLIGHT [str] [int]: Set backlight level(values are on, off) (BACKLIGHT string)

[312] SETBALANCE [int]: set balance value (SETBALANCE value)

[313] SETBANNERLOGO [str] [int]: Sets banner logo with given parameter for test, valid
parameters are : dolby, dolbyplus, dolbyvision, dts, hdr, hlg

[314] SETBASSGAIN [int]: set bass gain level (SETBASSGAIN value)

[315] SETBLUESTRECH [int]: set bluestrech (0:off 1:on)(SETBLUESTRECH value)

[316] SETBRIGHTNESS [int]: set picture brightness value (SETBRIGHTNESS value)

[317] SETBROADCASTDSMCCMHEGBLOCKING [int]: Enables or disables ACF Broadcast (DSMCC)

MHEG block

[318] SETCHANNEL [int]: set current channel (CHANNEL LIST VALUE)

[319] SETCOBALTURL [str]: Loads the given URL via COBALT browser

[320] SETCOLOUR [int]: set picture colour value (SETCOLOUR value)

[321] SETCOLOURSHIFT [int]: set colour shift value (SETCOLOURSHIFT value)

[322] SETCONTENTRES [int]: Set content resolution (1280x720: 0, 1920x1080: 1, Delete: 99)

[323] SETCONTRAST [int]: set picture contrast value (SETCONTRAST value)

[324] SETCONTROLLEDPOPUPTIMER [int]: Set controlled popup message timer
(SETCONTROLLEDPOPUPTIMER n)

[325] SETCOUNTRY [str] [int]: set country in no channels state (SETCOUNTRY string)

[326] SETCURSORPOSITION [str] [int]: sets cursor position in the browser (SETCURSORPOSITION x
y)

[327] SETCUSTOMERNAME [str]: set customer name variable (SETCUSTOMERNAME string)

[328] SETDAPMODE [str] [int]: set DAP mode (SETDAPMODE mode //mode = OFF or SMART or
MOVIE or MUSIC or NEWS//)

[329] SETDEFAULTGATEWAY [str]: set default gateway (default gateway value should be of format
nnn.nnn.nnn.nnn) (eg. SETDEFAULTGATEWAY nnn.nnn.nnn.nnn)

[330] SETDEVICEREGISTRATIONCHECKINTERVAL [int]: sets device registration check interval in

mins

[331] SETDIGITALOUT [str] [int]: set digital out (SETDIGITALOUT string)

[332] SETDIGITURK [int]: enables Digiturk search

[333] SETDNS1 [str]: set DNS server 1 (DNS server 1 value should be of format nnn.nnn.nnn.nnn)
(eg. SETDNS1 nnn.nnn.nnn.nnn)

[334] SETDNS2 [str]: set DNS server 2 (DNS server 2 value should be of format nnn.nnn.nnn.nnn)
(eg. SETDNS2 nnn.nnn.nnn.nnn)

[335] SETDNSCONFIGURATION [str]: set DNS configuration mode (auto,manual) (eg.

SETDNSCONFIGURATION mode (auto,manual))

[336] SETDSMART [int]: enables Dsmart search

[337] SETDYNAMICBASS [int]: set dynamic bass value (SETDYNAMICBASS value)

[338] SETDYNAMICCONTRAST [int]: Set Dynamic Contrast Level (LOW: 0 , MEDIUM: 1 , HIGH: 2,
OFF: 3)

[339] SETEQMODE [str] [int]: set equalizer mode (SETEQMODE string)

[340] SETEQUSERFREQ [str] [int]: set equalizer user freq. value for any band (SETEQUSERFREQ
band value)

[341] SETFILMMODE [str] [int]: Set film mode (values are OFF, AUTO) (SETFILMMODE string)

[342] SETFIXEDPICTUREMODE [str]: set Picture Mode availability (ON, OFF)

[343] SETFOLLOWTVDEVICESTATUS [int]: set follow tv device status (SETFOLLOWTVDEVICESTATUS

n)

[344] SETFRANSAT [int]: enables Fransat search

[345] SETHDMITRUEBLACK [str] [int]: Set hdmitrueblack state (values are ON, OFF)
(SETHDMITRUEBLACK string)

[346] SETHEADPHONEOUTPUT [str]: Set headphone output n(n is one of headphone or lineout)

[347] SETHOSTNAME [str]: Set Hostname

[348] SETHUE [int]: set picture hue value (SETHUE value)

[349] SETMAXVOLUME [int]: set volume maximum level in Hotelmode (VOLUME n)

[350] SETMAXVOLUME [int]: set volume maximum level in Hotelmode (VOLUME n)

[351] SETMBSUBTFONTSIZE [int]: set media browser subtitle size to n (56,63,67,74,81)

[352] SETMBSUBTLANG [str]: set subtitle language to n(alb, ara, bel, bos, bul, cat, hrv, cze, dan,
dut, eng, est, fin, fle, fre, gla, ger, gre, heb, hun, ice, ita, kaz, lav, lit, mac, cnr, nor, per, pol,
por, rum, rus, srp, slo, slv, spa, swe, tha, tur, ukr, wel, vie)

[353] SETMBSUBTPOS [str]: set subtitle position to n (up, down)

[354] SETMICRODIMMING [int]: Set Micro Dimming Level (LOW: 0 , MEDIUM: 1 , HIGH: 2, OFF: 3)

[355] SETMINVOLUME [int]: set minimum volume level in Hotelmode (VOLUME n)

[356] SETMODELNO [str] [int]: ex: SETMODELNO 19PFL3007E/12

[357] SETMUTE: set the volume mute/unmute according to the mute on/off

[358] SETNETWORKTYPE [str]: set network type (eg. SETNETWORKTYPE value) (value should be
'wired', 'wireless' or 'disabled' as string)

[359] SETNOISEREDUCTION [str] [int]: Set noise reduction state (values are OFF, LOW, MEDIUM,
HIGH) (SETNOISEREDUCTION string)

[360] SETOADTIME [str]: Sets time of nightly oad (Example: SETOADTIME 03:00)

[361] SETOWB [str] [int]: set osd white balance value (SETOWB type value
(type:redgain,greengain,bluegain,brightness value:0-255))

[362] SETPANELLOCK [str]: set Panel Lock availability (ON, OFF)

[363] SETPROXY [str] [int]: Sets proxy to be used (SETPROXY proxy_string as example.com:8080)

[364] SETQUICKSTANDBY [str]: SETQUICKSTANDBY n, where n is one of (off, on)

[365] SETQUICKSTANDBYOPTION [str]: SETQUICKSTANDBYOPTION n, where n is ON/OFF

[366] SETRC [str] [int]: Enables/disables remote control commands ex: SETRC ON, SETRC OFF

[367] SETRCU [str] [int]: Set RCU Inhibit

[368] SETRDSERVERURL [str] [int]: set remote diagnostic server url and port number(url port)
[369] SETREGISTRATIONID [str]: sets registration ID to PubSub instance (SETREGISTRATIONID
registration_id)

[370] SETREMOVECHANNEL [int]: deletes the channel which has been entered in hotelmode

[371] SETSDRTOHDR [int]: set sdr to hdr (0:off 1:on)(SETSDRTOHDR value)

[372] SETSERIALNO [str] [int]: ex: SETSERIALNO YN1A1234000001

[373] SETSHARPNESS [int]: set picture sharpness value (SETSHARPNESS value)

[374] SETSKINTONE [int]: set picture skin tone value (SETSKINTONE value)

[375] SETSLIDESHOWINTERVAL [int]: set slide show interval n seconds(5,10,15,20,25,30)

[376] SETSOUNDMODE [int]: Set sound mode (SETSOUNDMODE value)

[377] SETSOUNDOUTPUT [str]: Set sound output n(n is one of tv, spdif, arc, headphone or lineout)

[378] SETSOUNDSYSTEM [str] [int]: set sound system (SETSOUNDSYSTEM string)

[379] SETSOURCE [str] [int]: Set source as enable/disable (SETSOURCE source value)

[380] SETSPEAKERS [str] [int]: It sets the audio values as if headphone is connected to TV with the
values(Headphone state 1-0)

[381] SETSTARTCHANNEL [int]: set startup channel which has been entered in hotelmode

[382] SETSTARTUPMODE [str] [int]: set startup mode which has been entered in hotelmode Last
Status(Standbye, ON, LastStatus)

[383] SETSTARTUPSOURCE [int]: set startup source which has been entered in hotelmode(0-15)

[384] SETSTARTURL [str]: Set Start URL

[385] SETSTARTVOLUME [int]: set startup volume in Hotelmode (VOLUME n)

[386] SETSTATS [int]: Set statistics

[387] SETSTOREMODE [int]: set store/home mode

[388] SETSUBNETMASK [str]: set subnet mask (subnet mask value should be of format
nnn.nnn.nnn.nnn) (eg. SETSUBNETMASK nnn.nnn.nnn.nnn)

[389] SETSUBTSOURCE [int]: Set the subtitle source (SETSUBTSOURCE 0=none or index from
SHOWSUBTSOURCE)

[390] SETSURROUNDSOUND [int]: set surround sound value (SETSURROUNDSOUND value)

[391] SETTELNET [int]: Set Telnet support (Disabled: 0, Enabled: 1)

[392] SETTIMEMODE [str]: Set time mode (SETTIMEMODE mode (auto, manual)

[393] SETTKGS [int]: enables TKGS search

[394] SETTVLOCK [str] [int]: ex: SETTVLOCK USR?LCK-YN1A1234000001-25/04/2017-10/05/2017-1-
1-

[395] SETURL [str]: Loads the portal with the given URL as the start page. Returns web page load
status via portal

[396] SETUSBAUTOPLAY [str]: set usb autoplay to n(ON, OFF)

[397] SETUSBOPTION [str]: set USB Option (ON, OFF, 5V)

[398] SETUSERAGENT [str]: Sets portal user agent (SETUSERAGENT ua_string)

[399] SETWB [str] [int]: set white balance value (SETWB type value
(type:redgain,greengain,bluegain,redoffset,greenoffset,blueoffset value:0-255))

[400] SETWIFIAPCHANNEL [int]: sets the channel of the wifi access point

[401] SETWIFIAPSECURITYPASSWORD [str]: sets the password of access point. Password must be
maximum 64 characters

[402] SETWIFIAPSECURITYTYPE [str]: sets the security type of access point. The value should be
none or WPA2-PSK

[403] SETWIFIAPSSID [str]: sets the SSID of access point. SSID must be maximum 32 characters

[404] SETWIFIAPSTATE [str]: sets the access point state. State should be off or on.

[405] SETWIFIAPTXPOWER [int]: sets TX Power for wifi access point. TX Power should be in the
range of 0 - 20 dbm (0 for default value)

[406] SET_JB_TIME [int]: Set JB time in seconds

[407] SET_OFF_RS [int]: Set off rs time in seconds

[408] SET_OSD_MENU [int]: Set osd menu status

[409] SET_STBY_SEARCH_TIME [int]: Set standby serach time interval in minutes

[410] SFTI [str]: Set FirstTimeInstallation

[411] SFTP [str]: Set FTP Properties

[412] SHM [int]: Set Hotel Mode

[413] SHOWBUILDOPTIONS: Show build options

[414] SHOWNOW [int]: Show now&next info (SHOWNOW lcn/handle)

[415] SHOWSCHED [int]: Show next hours scheduled event info (SHOWSCHED lcn/handle)

[416] SHOWSTRING [str] [int]: Shows the string with given IDS and language index

[417] SHOWSUBTSOURCE: Show the subtitle sources

[418] SHOWSYSTEMLANGUAGES: Shows the system languages with language index and code
[419] SHOW_TEST_PATTERN [str] [int]: SHOW_TEST_PATTERN (enable) R(0 ~ 1023)-G(0 ~ 1023)-
B(0x0 ~ 1023) ex SHOW_TEST_PATTERN 0-125-11111-151515

[420] SHOW_TEST_PATTERN_PURE_COLOR [str] [int]: SHOW_TEST_PATTERN_PURE_COLOR

(enable) R(0 ~ 1023)-G(0 ~ 1023)-B(0x0 ~ 1023) ex SHOW_TEST_PATTERN_PURE_COLOR 0-125-
11111-151515

[421] SHW [int]: Show (1) Hide (0) WiDi

[422] SILENTRESET: Reset

[423] SLEEPTIMER2MINUTES: ex: SLEEPTIMER2MINUTES

[424] SMA [str] [int]: Vestel low level: Set mac address ex: eth0-00:01:02:03:04:05

[425] SMP [int]: Select MHEG profile

[426] SNTP [str]: Set NTP Server IP

[427] SOUNDRESET: reset sound settings

[428] SPJM [str]: send platform json message (string)

[429] SPM [str]: send platform message (string)

[430] SQI: signal quality indicator

[431] SRC [int]: Set Remote Control Code

[432] SSI: signal strength indicator

[433] SSIP [str]: Set static IP, Default Gateway and Subnetmask addresses of eth0 network
interface. Usage: SSIP [IPADDRESS-GATEWAY-SUBNETMASK] Example: SSIP 192.168.0.15-
192.168.0.100-255.255.255.0

[434] STANDBY: Switch box to Standby mode

[435] STANDBY_ICE [int]: Enter standby mode via direct ICE call

[436] STARTANALOGCHANNELMANUELSEARCH [str] [int]: start analog manual search with channel
parameters bandname:string channelnum:int. !!!Please set first sound system with
SETSOUNDSYSTEM function. (STARTANALOGCHANNELMANUELSEARCH <bandname>
<channelnum>)

[437] STARTANALOGFREQMANUELSEARCH [str] [int]: start analog manual search with frequency
parameters soundsystem:string frequency:int(KHz value) (STARTANALOGFREQMANUELSEARCH
soundsystem frequency)

[438] STARTAPS [str] [int]: start auto search (full :both digital&analog, analog: only analog, digital:
only digital search) (STARTAPS string)

[439] STARTFOLLOWTV: start follow tv feature

[440] STARTFOLLOWTVRECLIB [int]: start followtv for recording lib file with id
[441] STARTFTI: start First Time Installation

[442] STARTNETWORKDISCOVERY: starts network discovery feature (extended logging)

[443] STATS: Get statistics

[444] STATSTHRESHOLD [int]: Set statistics threshold for slow functions

[445] STEA: Stop emergency alarm

[446] STL [str] [int]: Set TV Language (e.g. 'en')

[447] STOPFOLLOWTV: stop follow tv feature

[448] STORESETTINGS: stores settings made for current channel number

[449] STV [int]: Set TV Volume

[450] STVCH [int]: set current channel (CHANNEL LIST VALUE)

[451] STWA: Stop wake up alarm

[452] SUBTOSDOFF: Subtitle OSD Off

[453] SUBTOSDON: Subtitle OSD On

[454] SWA [str]: Send wake up alarm

[455] SWOL [int]: Set Wake on Lan is disabled(0) or enabled(1) (ex: SWOL 1)

[456] SetCustomer [int]: Changes the Channel Table of TV in test mode (SetCustomer n) 0 for
Vestel etc.

[457] TENSECTRACE: Toggle 10-second trace of local time

[458] TIME: Display the current date and time

[459] TN [int]: Send Message/Trigger notification

[460] TOF: Turn Off TV

[461] TON [int]: Turn On TV

[462] TUNEDVBS [str] [int]: start sat manual search with parameters (TUNEDVBS frequencykhz-
polarisation-symbolrate-antennatype)

[463] TVURL [str]: starts a URL thru VODServiceManager

[464] UARTLOGOUT [int]: Set the Uart logs to ON/OFF. ( 0:off, 1:on) - int

[465] UARTLOGOUT [int]: Uart Logs(out) are disabled or enabled (ex: UARTLOGOUT 1)

[466] UARTOUTPUTSTART: Start UART Output

[467] UARTOUTPUTSTOP: Stop UART Output

[468] UCL: Update Channel List

[469] UISUBTOFF: Stop subtitle decoding and hide subtitles

[470] UISUBTON: Start subtitle decoding and show subtitles

[471] UITTXTOFF: Stop and hideteletext

[472] UITTXTON: Start and show teletext

[473] UNITTESTS [int]: [q] Run unit tests (q => only run quick tests)

[474] UNP [str]: Send Message

[475] UNTP: Update Date and Time

[476] UPDATELOGCONFIG: updates extended logging configuration from server

[477] UPF [str]: Update Profile Files

[478] UPSEARCH [int]: Search for software update (UPSEARCH tuner_id)

[479] UPSTOP: Stop the search for software update

[480] UPTIME: Gets TV's up time

[481] USBOPERATIONS: Perform USB Operations

[482] USBSWUPDATE: Updates software from usb and re-boots

[483] VIDEOPLAY [str] [int]: Play Video file (VIDEOPLAY /media/sda1/video.mkv)

[484] VIDEOSTOP: Stop Video file (VIDEOSTOP)

[485] VIDOFF: Select video off

[486] VIDON: Select video on

[487] VOLUME [int]: set volume level (VOLUME n)

[488] VOLUMEDOWN: Decrease Volume Level by 1 step

[489] VOLUMEUP: Inrease Volume Level by 1 step (Until max volume)

[490] VPOS [int]: Set vertical position (VPOS n)

[491] WATCHDOG [int]: Watchdog control: 0-Enable 1-disable 2-stop kicking, N-kick every n
seconds

[492] WAU [int]: SW Auto Upgrade

[493] WSS [int]: Set WSS Aspect Ratio Code: 0-7

[494] Wifi [str]: checks if given SSID wifi is found or not and returns Pass or Fail. Works only in
portal mode

[495] WifiConnectTest2 [str]: checks if given SSID wifi is connectable or not and returns Pass or Fail

[496] WifiConnectTest5 [str]: checks if given SSID wifi is connectable or not and returns Pass or Fail
[497] allocmem [int]: Allocates specified amount of memory in megabytes (a negative value exits
the thread): allocmem 250

[498] ber_test [str] [int]: start ber test mode with the specified period. Set 0 to stop ber test mode
ex: ber_test 100

[499] browser_gop_status: Return Browser GOP Status

[500] check_CIP: Vestel low level: check whether Credentials Keys is ok

[501] check_dovi: returns if DoVi config is OK/NOK

[502] check_ecp: Vestel low level: Checks if ecp key is written on SPI flash or not ex: check_ecp

[503] check_esn: Vestel low level: Checks the Idfile content in Spi flash ex: check_esn

[504] check_hdcp: Vestel low level: check whether HDCP is ok

[505] check_hdcp20: Vestel low level: check whether HDCP V2 is ok

[506] check_marlin: Vestel low level: Checks if marlin drm key is written on SPI flash or not ex:
check_marlin

[507] check_playready: Checks if the playready key files exist, ex: check_playready

[508] check_smarthome: Checks the SmartHome feature of the Mainboard

[509] check_usb_plugged: Vestel low level: Checks whether usb plugged or not

[510] check_widevine: Vestel low level: Checks if widevine key is written on SPI flash or not ex:
check_widevine

[511] clearOSD: clears OSDs

[512] crash_the_system: Crashes the system by assigning to a nullptr.

[513] deallocmem [int]: Frees specified amount of memory in megabytes if allocmem testtool
command is used before (a negative value exits the thread): deallocmem 250

[514] debugout [str]: Enable or disable the UART output. Set 'on' or 'off'.

[515] dlna [str] [int]: dlna prompt

[516] enable_browser_gop [int]: Enable/Disable Browser GOP

[517] enable_subtitle_gop [int]: Enable/Disable Subtitle GOP

[518] get_IP_address: Get IP address of eth0 network interface. Usage: get_IP_address

[519] get_SW_Device: Returns the software version of tv, ex: GETSWVERSION

[520] get_bootlogo_name: Get the name of the boot logo

[521] get_gamma_curve:

[522] get_gamma_single_point [str] [int]: index(0~1024) e.x. 512

[523] get_isitCornerIC: Get is it Corner IC

[524] get_mac_address: Vestel low level: Get MAC address

[525] get_panel_cursor [str] [int]: X(0~3840) Y(0~2160) e.x. 1920,1080

[526] get_tv_id: returns a numeric tv id entered through hotel menu

[527] getbuffer: Checks available size of the buffer partition for diagnostic

[528] gracenotestatus: Reports gracenote status

[529] help: List all regitered commands.

[530] inject_ait_url [str]: Injects an AIT XML URL into the browser and returns web page load
status via portal

[531] ipdown: IP connection down

[532] ipup: IP connection up

[533] is_in_test_mode: Get test mode state

[534] list_all_thread: Vestel low level: Lists all thread

[535] loop_stream: change the playback stream

[536] ntkmenu: Enter to NTK debug menu

[537] out_of_memory: Exhausts system memory to cause a crash.

[538] ping_for_eth_ready: Vestel low level: Test For ethernet control

[539] print_profile: Vestel low level : print sw and hw profile values

[540] print_profile: Prints hw, sw and dev profile values

[541] replay_stream: change the playback stream

[542] restart: Vestel low level: reboot the system

[543] rm_bt_dev [int]: Remove Bluetooth device. Parameter is index in BT paired devices database

[544] rt_gaci: Cabot Internal: Get all channels' info

[545] rt_gaud2pid: Cabot Internal: Get secondary audio pid

[546] rt_gaudpid: Cabot Internal: Get audio pid

[547] rt_gcnlan: Cabot Internal: Get channel list names and numbers

[548] rt_gcnn: Cabot Internal: Get current network name

[549] rt_gcsse [str] [int]: Cabot Internal: Get current service schedule events

[550] rt_gdspid: Cabot Internal: Get data service pid

[551] rt_geei: Cabot Internal: Get extended event information

[552] rt_gfe: Cabot Internal: Get following event

[553] rt_gnlc: Cabot Internal: Get number of logical channels

[554] rt_gpe: Cabot Internal: Get present event

[555] rt_grt: Cabot Internal: Get receiver time

[556] rt_gscrmi: Cabot Internal: Get scrambled indicator

[557] rt_gsn: Cabot Internal: Get current service name

[558] rt_gsp: Cabot Internal: Get current service provider

[559] rt_gsrvt: Cabot Internal: Get service type

[560] rt_gss: Cabot Internal: Get service status

[561] rt_gsubpid: Cabot Internal: Get subtitle pid

[562] rt_gtlcs: Cabot Internal: Get time of last channel scan

[563] rt_gvidpid: Cabot Internal: Get video pid

[564] rt_rsn [int]: Cabot Internal: Reset sequence number

[565] runOsdTest: RUN OSD TEST

[566] screen_capture_usb [int]: Capture specified surface as bmp to USB stick. 0 for UI, 1 for
MHEG, 2 for Teletext, 8 for video

[567] set_IP_address [str] [int]: Set static IP address of eth0 network interface. Usage:
set_IP_address [IP ADDRESS] Example: set_IP_address 192.168.0.15

[568] set_backlight [str] [int]: Set backlight level(values are on, off) (BACKLIGHT string)

[569] set_gamma_single_point [str] [int]: index(0~1024) Red(0~4095) Green(0~4095)

Blue(0~4095) e.x. 1024,0,2048,4095

[570] set_html_plugin_profile_status [str] [int]: sets html plugin profile status

[571] set_mac_address [str] [int]: Vestel low level: Set mac address ex: eth0-00:01:02:03:04:05

[572] set_pq_test_pattern [str] [int]: Enable State( 0:Disable, 1:Enable) Red(0~255) Green(0~255)
Blue(0~255) e.x. 1,128,0,255

[573] set_tv_id [str]: sets tv id

[574] set_usb_enable [str] [int]: Vestel low level: Sets USB(s) Enable State, 0->Disable, 1->Enable

[575] signal_monitor [str]: Enables/Disables signal monitoring utility

[576] start_test_mode: Vestel low level: Start test mode for wxga panel
[577] subtitle_gop_status: Return Subtitle GOP Status

[578] suspend: Enter STR mode

[579] test_speed [int]: Test CPU speed. [1] for Dhrystone, [2] for Whetstone, [3] for Opera

[580] test_spi_magic [int]: Write spi magic code for test. Case 0 for 0x00, Case 1 for 0xFF,Case 2 for
ROFIXBAK , Case 3 Unknown

[581] throw_exception: Throws an std::bad_alloc exception.

[582] uo: Perform USB Operations (same as USBOPERATIONS but less to type!)

[583] write_gamma_data:

testtool > 00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange

BIEP Network change

00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange Tag:

appid: 7366620224246206057

00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange Tag:

name: BIEP Network change

00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange Tag:

nrdpSuspendState: true

00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange Tag:

remainingRetryTIme: 1702.63

00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange Tag:

retrycount: 1

00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange Tag:

timeElapsed: 119652

00:01:59.659 [GIBBON_MAIN:0x759aa000] UI_SCRIPT(error): type=biepnetworkchange Tag: type:

biepnetworkchange

00:01:59.674 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-97,"hst":"nrdp51-appboot.netflix.com","srv":"(8.8.8.8)","tim":19}

00:01:59.674 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"nrdp51-appboot.netflix.com","srv":"(8.8.8.8)","tim":18}

00:01:59.674 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"nrdp.nccp.netflix.com","srv":"(8.8.8.8)","tim":18}

00:01:59.674 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"nrdp.nccp.netflix.com","srv":"(8.8.8.8)","tim":18}

00:01:59.674 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"api-global.netflix.com","srv":"(8.8.8.8)","tim":18}
00:01:59.674 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup
{"adt":"ipv6","err":-76,"hst":"api-global.netflix.com","srv":"(8.8.8.8)","tim":18}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"secure.netflix.com","srv":"(8.8.8.8)","tim":19}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"secure.netflix.com","srv":"(8.8.8.8)","tim":19}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"uiboot.netflix.com","srv":"(8.8.8.8)","tim":19}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"uiboot.netflix.com","srv":"(8.8.8.8)","tim":19}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"customerevents.netflix.com","srv":"(8.8.8.8)","tim":18}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"customerevents.netflix.com","srv":"(8.8.8.8)","tim":18}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-97,"hst":"ichnaea.netflix.com","srv":"(8.8.8.8)","tim":18}

00:01:59.675 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"ichnaea.netflix.com","srv":"(8.8.8.8)","tim":18}

00:02:00.007 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-97,"hst":"cdn-0.nflximg.com","srv":"(8.8.8.8)","tim":349}

00:02:00.007 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"cdn-0.nflximg.com","srv":"(8.8.8.8)","tim":350}

[3-169.710873] [NTKETHMAC] Eth Unplug is detected : 00007809

00:02:06.394 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"nrdp51-appboot.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.394 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"nrdp.nccp.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.394 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"api-global.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"secure.netflix.com","srv":"(8.8.8.8)","tim":6387}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"uiboot.netflix.com","srv":"(8.8.8.8)","tim":6387}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"customerevents.netflix.com","srv":"(8.8.8.8)","tim":6387}
00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup
{"adt":"ipv6","err":-76,"hst":"ichnaea.netflix.com","srv":"(8.8.8.8)","tim":6387}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv6","err":-76,"hst":"cdn-0.nflximg.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"nrdp51-appboot.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"nrdp.nccp.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"api-global.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"secure.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.395 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"uiboot.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.396 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"customerevents.netflix.com","srv":"(8.8.8.8)","tim":6386}

00:02:06.396 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"ichnaea.netflix.com","srv":"(8.8.8.8)","tim":6387}

00:02:06.396 [DNS_MANAGER:0x728e3450] DNS_MANAGER(error): type=dnslookup

{"adt":"ipv4","err":-76,"hst":"cdn-0.nflximg.com","srv":"(8.8.8.8)","tim":6387}

[DIALSERVER] connect status change ( 1->0 ).

[DIAL-SERVER] ssdp check-running() error.

run_ssdp exit