0% found this document useful (0 votes)
9 views2 pages

PDC Imp Questions

The document outlines a syllabus for a course on Pulse and Digital Circuits, detailing various topics across three units. Key concepts include the operation of RC circuits as integrators and differentiators, clamping circuits, diode recovery times, and transistor switching. Each unit contains specific problems and explanations related to circuit design and analysis.

Uploaded by

nadarujeevan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
9 views2 pages

PDC Imp Questions

The document outlines a syllabus for a course on Pulse and Digital Circuits, detailing various topics across three units. Key concepts include the operation of RC circuits as integrators and differentiators, clamping circuits, diode recovery times, and transistor switching. Each unit contains specific problems and explanations related to circuit design and analysis.

Uploaded by

nadarujeevan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Subject: PULSE AND DIGITAL CIRCUITS

Class : II ECE
UNIT-I
1. Prove that a low pass circuit acts as an integrator. Derive an expression for the output voltage
levels under steady state conditions of a low pass circuit excited by a ramp input. 7M

2. With the circuit diagram and waveforms explain the operation of RC circuits as Integrators
and differentiators for a square wave input.7M

3. Draw the different output waveforms of a RC Low Pass circuit when it is applied with
Different inputs like (a) Step-voltage input (b) pulse input C) Square input? 7M

4. With the help of circuit diagrams, explain the working of RC and RL low-pass circuits? 7M

5. Define Integrator and condition for good integrator circuit.3M

6. Prove that et = T/2RC for ramp as input to the High pass RC-Circuit? 6M

7. Sketch the response of low pass RC circuit for step input and derive the expression for rise
time. 8M

8. An ideal 2µs pulse is fed to an amplifier. Calculate and plot the output waveform when the
upper 3-dB frequency is (a) 5 MHz and (b) 0.05 MHz 8M

9. Write short notes on Ringing Circuit.5M

10. A 1 KHz square wave output from an amplifier has rise time tr = 350 ns and tilt = 5 %.
Determine the upper and lower 3- dB frequencies.10M

UNIT-II
1. With neat circuit diagram, explain the working of an emitter coupled clipper. 8M
2. State and prove clamping circuit theorem. 8M
3. A symmetrical 50 Hz square wave whose peak to peak excursions are ± 100 V with
respect to ground is to be positively clamped at 25 V. Draw the necessary circuit diagram
and output waveform for this purpose. 10M
4. What is the difference between linear wave shaping and non linear wave shaping? 5M
5. Explain the clamping circuit considering the source resistance and the diode forward
resistance. 10M
6. Draw a circuit to transmit that part of a sine wave, which is below + 6 V. 5M
7. With the help of a neat circuit diagram, explain the working of a two-level clipper? 7M
8. Draw the basic circuit diagram of negative clamper circuit and explain its operation using
waveforms? 5M
9. Explain about two level clipping with a neat diagram and waveforms.6M
10. Write a short notes on Noise clippers. 5M

UNIT-III
1. Define diode forward recovery time and diode reverse recovery time? 3M

2. Briefly explain about: (i) Diode switching and (ii) Transistor switching times 6M

3. Discuss about the design of Transistor as a switch? 7M

4. Define Storage time and Transition time of a diode? 3M

5. What are different types of multivibrators? Explain the stable state and quasi stable state of a
multivibrator. 5M

6. With neat circuit diagram, Explain the working of fixed bias bistable multi vibrator.10M

7. Explain how a transistor acts as a switch with neat circuit diagram.5M

8.Evaluate stable state currents and voltages for the fixed bias binary? 5M

You might also like