PRODUCT SPECIFICATIONS

For Customer: ___ _____ □ : APPROVAL FOR SPECIFICATION

Customer Model No. _ _ □ : APPROVAL FOR SAMPLE
Module No.: 7" TFT with CTP Date : 2019‐11‐10
Table of Contents
No. Item Page
1 Cover Sheet(Table of Contents)
2 Revision Record
3 General Specifications
4 Outline Drawing
5 Absolute Maximum Ratings
6 Electrical Specifications
7 Optical Characteristics
8 Reliability Test Items and Criteria
9 Precautions for Use of LCD Modules

For Customer ’s Acceptance:

Approved By Comment

PREPARED CHECKED VERIFIED BY QA DEPT VERIFIED BY R&D DEPT

Version :1 Page:1/17
2. Revision Record

Date Rev.No. Page Revision Items Prepared

www.mikroe.com Page:2/17
3. General Specifications
7" TFT with Capacitive Touch Screen is composed of a TFT - LCD panel, driver IC, FPC, TP, a back
light unit. The 7" display area contains 800 x 480pixels and can display up to 16.7M colors.
This product accords with RoHS environmental criterion.

Note 1: Color tune is slightly changed by temperature and driving voltage.

Note 2: Without FPC and Solder.

Item Contents Unit Note

LCD Type TFT -

Display color 16.7M
Viewing Direction 12 O’Clock

Gray scale inversion direction 6 O’Clock

Operating temperature -20~+70 ℃
Storage temperature -30~+80 ℃
Module size Refer to outline drawing mm
Active Area(W×H) 154.08X85.92 mm
Number of Dots 800×480 dots
LCM Controller HX8664&HX8262 -
CTP Controller FT5426
Power Supply Voltage 3.3 V
Refer to outline
Outline Dimensions -
drawing
Backlight 3X9-LEDs (white) pcs
Weight --- g
Interface RGB-24bit -

www.mikroe.com Page:3/17
 REVISE Revision note DATE NAME
V0 First

www.mikroe.com
4.Outline.Drawing

7.0"TFT
800*RGB*480

BACK

FRONT
12 o'clock

BENDING AREA
BLACK PRINTING

compionent
STEEL STIFFENER(T= 0.2MM)
compionent

CONTACT SIDE STIFFENER PI NAME

DETAIL B
1 10

50 1
DETAIL A

1 10
50 1

NOTES:
DETAIL A (2:1) DETAIL B (4:1)
1. DISPLAY TYPE: 7.0"TFT,TRANSMI SSIVE
2. VIEWING DIRECTION : U/L/D/R 6 5/65/55/65
3. Driver IC : GATE HX8664-B & S OURCE HX8264-E LED CIRCUIT DIAGRAM:
A(VLED+)
4. CTP Driver IC : FT5426 Approved By
SIZE: TFT_LCD 7.0"
5. Top : -20°C ~ 70°C, Tst : -30 °C ~ 80°C K(VLED-) Checked By
9*3=27EA If=180mA
6. GENERAL TOLERANCE: ±0.2 DWARING_NO.:
Drawn By
7. LCM Luminance:LED/420cd/m 2(Ty pical) CUSTOMER_NO.

Page:4/17
UNIT:mm
5. Absolute Maximum Ratings(Ta=25℃)
5.1 Electrical Absolute Maximum Ratings.(Vss=0V ,Ta=25℃)

Item Symbol Min. Max. Unit Note

Power Supply Voltage VCC -0.3 3.6 V 1，2

Notes:

1. If the module is above these absolute maximum ratings. It may become permanently damaged. Using the

module within the following electrical characteristic conditions are also exceeded, the module will malfunction

and cause poor reliability.

2. VCC >VSS must be maintained.

5.2 Environmental Absolute Maximum Ratings.

Storage Operating
Item Note
MIN. MAX. MIN. MAX.
Ambient Temperature -30℃ 80℃ -20℃ 70℃ 1,2

Humidity - - - - 3

1. The response time will become lower when operated at low temperature.

2. Background color changes slightly depending on ambient temperature.

The phenomenon is reversible.

3. Ta<=40℃:85%RH MAX.

Ta>=40℃:Absolute humidity must be lower than the humidity of 85%RH at 40℃.

www.mikroe.com Page:5/17
6. Electrical Specifications and Instruction Code
6.1 Electrical characteristics(Vss=0V ,Ta=25℃)

Parameter Symbol Condition Min Typ Max Unit Note

Power supply VCC Ta=25℃ 3.0 3.3 3.6 V

Input ‘H’ VIH VVCC=3.3V 0.8VCC - VVCC V

voltage
‘L’ VIL VVCC=3.3V 0 - 0.2VVCC V
Normal
IDD1 - - - mA 1
Current mode
Consumption
IDD2 Sleep mode - - - mA 1

6.2 LED backlight specification(VSS=0V ,Ta=25℃)

Item Symbol Condition Min Typ Max Unit Note

Supply voltage Vf If=20X9mA 8.4 9.0 11 V

Uniformity ΔBp If=20X9mA 75 %

ILED VS TEMP

www.mikroe.com Page:6/17
6.3 Interface signals

Pin No. Symbol I/O Function

1-2 VLED+ P LED back light(Anode)
3-4 VLED- P LED back light(Cathode)
5 GND P Ground.
6 VCC P Power supply
7 VCC P Power supply
8 MODE I DE/YSNC mode select
9 DE I Data enable pin
10 VSYNC I Frame sync signal
11 HSYNC I Line sync signal
12-19 B7~B0 I Blue data bus
20-27 G7~G0 I Green data bus
28-35 R7~R0 I Red data bus
36 GND P Ground.
37 DCLK I Data clock
38 GND P Ground.
39 L/R I Right/Left sequence control of source driver
40 U/D I Gate driver Up/Down scan control of gate driver
41 VCC P Power supply
42 VCC P Power supply
43 NC - No connection.
44 RESET I Chip reset pin
45 NC - No connection.
46 NC - No connection.
47 DITHB I Dithering function
48 GND P Ground
49-50 NC - No connection.

CTP interface

Pin No Symbol I/O Function

1 VSS P Ground
2 VDD P CTP Power supply
3 SCL I Serial clock
4 NC - No connection.
5 SDA I Serial Input/output data bus
6 NC - No connection.
7 /RST I Reset the display
8 /WAKE - No connection.
9 /INT I External Interrupt to the IC of CTP
10 VSS P Ground

www.mikroe.com Page:7/17
6.4 AC Characteristics
6.4.1 AC electrical characteristics

www.mikroe.com Page:8/17
6.4.2 data input format

6.5 Waveform
6.5.1 parallel RGB mode

www.mikroe.com Page:9/17
 6.5.2 Timing waveform table
6.5.2.1 input clock and data timing waveform

6.5.2.2 Source output timing waveform(Cascade)

6.5.3Vertical timing diagram DE(Cascade)

www.mikroe.com Page:10/17
7. Optical Characteristics

Item Symbol Condition Min. Typ. Max. Unit Note

Brightness Bp θ=0° - 420 - Cd/m2 1

Uniformity ⊿Bp =0° 75 - - % 1,2
3:00 - 65 -

Viewing 6:00 - 55 -
Cr≥10 Deg 3
Angle 9:00 - 65 -
12:00 - 65 -
Contrast
Cr 300 500 - 4
Ratio
θ=0°
Response Tr =0° - 10 - ms
5
Time Tf - 10 - ms
x 0.28 -
W
y 0.33 -
x 0.51 -
R
Color of y 0.34 -
CIE
x θ=0° 0.31 -
Coordinate 1,6
G =0°
y 0.56 -
x 0.15 -
B
y 0.14 -
NTSC
S 50 60 - %
Ratio

Note：The parameter is slightly changed by temperature, driving voltage and materiel

Note 1: The data are measured after LEDs are turned on for 5 minutes. LCM displays full white. The
brightness is the average value of 9 measured spots. Measurement equipment PR‐705 (Φ8mm)
Measuring condition:
- Measuring surroundings: Dark room.
- Measuring temperature: Ta=25℃.
- Adjust operating voltage to get optimum contrast at the center of the display.
Measured value at the center point of LCD panel after more than 5 minutes while backlight
turning on.

www.mikroe.com Page:11/17
Note 2: The luminance uniformity is calculated by using following formula.
⊿Bp = Bp (Min.) / Bp (Max.)×100 (%)
Bp (Max.) = Maximum brightness in 9 measured spots
Bp (Min.) = Minimum brightness in 9 measured spots.

Active area

Note 3: The definition of viewing angle:

Refer to the graph below marked by θ and Ф

Note 4: Definition of contrast ratio.( Test LCD using DMS501)

www.mikroe.com Page:12/17
 Contrast ratioCr  
Brightness of selected dots
Brightness of non  selected dots
Note 5: Definition of Response time. (Test LCD using DMS501):
The output signals of photo detector are measured when the input signals are changed from
“black” to “white”(falling time) and from “white” to “black”(rising time), respectively. The response
time is defined as the time interval between the 10% and 90% of amplitudes.Refer to figure as
below.

The definition of response time

Note 6: Definition of Color of CIE Coordinate and NTSC Ratio.

Color gamut:

area of RGB triangle

S  100%
area of NTSC triangle

Note 7: Definition of cross talk.

Cross talk ratio(%)=|pattern A Brightness‐pattern B Brightness|/pattern A Brightness*100

www.mikroe.com Page:13/17
 Pattern A Pattern B

Measurement point(center)

Electric volume value=3F+/‐3Hex

www.mikroe.com Page:14/17
8. Reliability Test Items and Criteria

No Test Item Test condition Criterion

80℃±2℃ 96H
1 High Temperature Storage Restore 2H at 25℃
Power off

-30℃±2℃ 96H
2 Low Temperature Storage Restore 2H at 25℃
Power off 1. After testing, cosmetic

70℃±2℃ 96H and electrical defects

3 High Temperature Operation Restore 2H at 25℃ should not happen.

Power on 2. Total current

consumption should not be
-20℃±2℃ 96H
more than twice of initial
4 Low Temperature Operation Restore 4H at 25℃
value.
Power on

60℃±2℃ 90%RH 96H

5 High Temperature/Humidity Storage
Power off
--30℃←-----------------→80℃
6 Temperature Cycle after 5 cycle, Restore 2H at 25℃
30min 5min 30min
Power off

7 Vibration Test 10Hz~150Hz, 100m/s2, 120min Not allowed cosmetic and

electrical defects.
8 Shock Test Half- sine wave,300m/s2,11ms

Note: Operation: Supply 3.3V for logic system.

The inspection terms after reliability test, as below
ITEM Inspection
Contrast CR>50%
IDD IDD<200%
Brightness Brightness>60%
Color Tone Color Tone+/-0,05

www.mikroe.com Page:15/17
9. Precautions for Use of LCD Modules
9.1 Handling Precautions
9.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a
high place, etc.
9.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to
get any in your mouth, if the substance comes into contact with your skin or clothes, promptly
wash it off using soap and water.
9.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause
the color tone to vary.
9.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle
this polarizer carefully.
9.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry
cloth. If still not completely clear, moisten cloth with one of the following solvents:
— Isopropyl alcohol — Ethyl alcohol
Solvents other than those mentioned above may damage the polarizer. Especially, do not use
the following:
— Water — Ketone — Aromatic solvents
9.1.6 Do not attempt to disassemble the LCD Module.
9.1.7 If the logic circuit power is off, do not apply the input signals.
9.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum
work environment.
a. Be sure to ground the body when handling the LCD Modules.
b. Tools required for assembly, such as soldering irons, must be properly ground.
c. To reduce the amount of static electricity generated, do not conduct assembly and other work
under dry conditions.
d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off
this protective film since static electricity may be generated.

www.mikroe.com Page:16/17
9.2 Storage precautions
9.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent
lamps.
9.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will
be stored for a long time, the recommend condition is:
Temperature : 0℃ ～ 40℃
Relatively humidity: ≤80%
9.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas.

9.3 The LCD modules should be no falling and violent shocking during transportation, and also should

avoid excessive press, water, damp and sunshine.

END

www.mikroe.com Page:17/17