Design of Steel Structure

STRUCTURAL CALCULATION FOR STEEL SLIDING GATE

IN THE WASTEWATER TREATMENT PROJECT
@ INDUSTRIAL AREA
QATAR - Rev.00

DECEMBER 2024
Design of Steel Structure

I/no. TABLE OF CONTENTS Remarks

1 Project Brief Information

2 Design Tools and References

3 Material and Design Section Properties

4 Design Load
4.1 Dead Load
4.2 Wind Load

5 Load Combination
5.1 Ultimate Load Limit State
5.2 Serviceability Load Limit State

6 Structural Analysis, Design and Results

6.1 3D SAP MODEL
6.2 LOADING
6.3 Member Design Detail and Results
6.4 Deflection Check
6.5 Design connections

7 Conclusion

8 Reference Plan, Section and Details

1
Design of Steel Structure

1- Project Brief Information

The following narrative report describes a brief design criterion of Sliding Gate steel framing in the Wastewater
Treatment Project at Industrial Area
Gate framing configuration and dimension is accordance to the reference drawing provided by the
contractor
.
2- Design Tools and References
Structural member element analysis was carried out using SAP2000 V.24 and IDEA STATICA
following the design code as follows;
o QCS-Qatar Construction Specification, 2014
o AISC 360-16 : Basis of Structural Design .
o AISC 360-16 : Actions on Structures .
o AISC 360-16 : Design of Steel Structures .
o ASCE 7-16 : Minimum Design Loads for Buildings and Other Structures .

3- Material and Design Section Properties

Steel Sections Mechanical Properties
Structural Steel Grade S275, Ps =275MPa
Poisson’s Ratio U, =0.30
Modulus of Elasticity E, =200GPa
Density W, =76.81kN/m3
Thermal Coefficient, A =1.2x10-5/oC

Bolt/Screw Properties
Grade 8.8, ft =800MPa
Weld Properties
Electrode E70, fu =480 MPa

STEEL SECTION

2
Design of Steel Structure

4- Design Load Calculation

4.1 DEAD LOAD
-DL- OW - Structure Self Weight .

4.2 WIND LOAD

Basic Wind Speed, V = 48 m/sec
Exposure from Ground ( <4.60 m), Kz = 0.85
Topographic Factor, Kzt = 1.0
Directionality Factor for Sign Boards, Kd = 0.85
Importance Factor, I = 1.0
Gust Effect Factor, G = 0.85
Force Coefficients, Cf = 1.6
Velocity Pressure, qz = 0.613Kz.Kzt.Kd.V2I = 1.02 Kn/m2
Wind Pressure, F= qz.G.Cf = 1.4 Kn/m 2
for SHS 30x30x2 , F= 1.4 x 0.03 = 0.04 Kn/m
for RHS 100x50x3, F= 1.4 x 0.1 = 0.14 Kn/m

5- Load Combination

3
Design of Steel Structure

6- Structural Analysis, Design and Results

6.1 - 3D SAP MODEL

5
SLIDING GATE.sdb

Z
Y
X

SAP2000 24.0.0 3-D View KN, mm, C

 KN, mm, C
RHCF100X50X3
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
3

SHCF 30X30X2
50X

SHCF 30X30X2
SHCF 30X30X2
RHCF100X

SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
RHCF100X50X3
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
X3
RHCF100X50

SHCF 30X30X2 SHCF 30X30X2

SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
RHCF100X50X3
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 50X3 SHCF 30X30X2
RHCF100X
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
RHCF100X50X3

3-D View
0X50X3
SHCF 30X30X2 SHCF 30X30X2
RHCF100X50X3

SHCF 30X30X2 SHCF 30X30X2

50X3

RHCF10
SHCF 30X30X2 SHCF 30X30X2

RHCF100X
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2 SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
RHCF100X50X3
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2

50X3
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2

RHCF100X
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
RHCF100X50X3
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SHCF 30X30X2

50X3
SHCF 30X30X2
SHC F 30X30X2

RHCF100X
SHC F 30X30X2
SHCF 30X30X2
SHCF 30X30X2
SLIDING GATE.sdb

SHCF 30X30X2
SHCF 30X30X2

SAP2000 24.0.0
SHCF 30X30X2

X
SHCF 30X30X2

Y
Z
RHCF100X50X3
 KN, mm, C
14
147
148
145
146
143
144
141
34

142
139
140
137
138
135
136
27
133 134
131 132
129 130
127
33

128
125 126
123 124
121 122
25
119 120
117 118
115 116
113 114
32
111 112
109 110
107 108
23

3-D View
105 106
103 104

17
15

101 102
99 100

31
97 98
95 96
94
93
21
92
91
90
89
88
87
86
85

71
84
83
82
81
80
79
19
63
62
61
60
59
58
57

42
56
55
54
SLIDING GATE.sdb

53
52

SAP2000 24.0.0
51

X
50

Y
Z
16
SLIDING GATE.sdb

155 158 16128

134 137 14018 143 146 149 152
103 106 109 112 115 11816 121 124 128 131
88 91 94 97 14 100
68 70 12 79 82 85
47 49 2 58 60 62 64 66
1 37 39 41 43 45

16231
150 153 156 159
36 144 147
129 132 135 138 141
35 122 125
110 113 116 119
104 107
98 34 101
89 92 95
78 33 80 83 86
75 76 77
72 73 74
54 55 56 57 32
30 51 52 53

29
166157 160 163
167151 154
145 148
136 139 14219
126 130 133
12017 123
114 117
105 108 111
99 15 102
93 96
87 90
13 81 84
71
67 69
16563 65
61
3 59
164
48 50
Z 44 46
Y 40 42
X 38
127

SAP2000 24.0.0 3-D View KN, mm, C

Design of Steel Structure

6- Structural Analysis, Design and Results

6. 2 - LOADING

11
SLIDING GATE.sdb

0 0.0 0.1
0 0 0.0 0.0 0.040.04 .04 4 4
0 0 0.0 0.0 0.0 0.04 .14 .04 4 4
0 0 0. 0 . 0.0 0.0 0.04 0.040.140.04 .04 .04 4 4 4
0 0 . 0 4
0. 0.0 0.0 0.0 0.04 .04 .04 .14 04 04 4 4
04 4 4 4
0.
0.
0.
0.0
0 .0
0.0
0 .0

14
0.04

04
0.14

04
0.04
0.04
0.04
0.04
0.04

4
0.04
4

4
4

4
4
0.0
0.1

0
0 0 0. .0
0 0. 0.0 .04 .04 04 4
0 0 0. 0.1 .04 04 4
0 0 0.0 0.0 0.04 .04 .04 04 4
0 .
0. 0.0 0.0 .04 .14 04 4 4
04 4 4
0.
0.
0.

04
0.
0.

04
0.

04
0.0

14
0.0

04
0 .0

04
0.0
0.0
0.1
0.0

4
0.0

4
0.04

4
0.04

4
0.04

4
0.04

4
0.04

4
0.14

4
0.04
0.04
0.04
0.04
0.04
0.04
0.04
0.14

Z
Y
X
0.14

SAP2000 24.0.0 Frame Span Loads (WIND) (GLOBAL CSys) KN, m, C

Design of Steel Structure

6- Structural Analysis, Design and Results

6.3- Member Design Detail and Results

15
 KN, m, C
0.189
0.087
0.06
0.078
0.059
0.071
0.061
0.048

0.066

1.00
0.08
0.066
0.112
0.066
0.133
0.065
0.125
0.213
0.065 0.108
0.059 0.108
0.057 0.104
0.217

0.056 0.097
0.054 0.088
0.053 0.078
0.052 0.067

0.90
0.123
0.051 0.052

Maximum Stress Ratios (AISC 360-16)

0.05 0.049
0.049 0.244 0.046
0.048 0.042
0.048 0.041
0.048 0.042
0.048 0.042
0.103
0.048 0.05

0.70
0.559
0.05 0.056
0.396

0.051 0.062

0.225
0.053 0.068
0.059 0.074
0.066 0.08
0.084
0.072
0.188
0.102
0.08
0.115
0.087
0.126

0.50
0.096

0.159
0.136
0.105
0.143
0.111
0.136
0.111
0.109
0.105
0.191
0.078
0.1
0.069
0.1
0.062
0.096

0.121
0.059

0.00
0.089
0.058
SLIDING GATE.sdb

0.082
0.058
0.074

SAP2000 24.0.0
X
0.057

Y
0.066

Z
0.129
Design of Steel Structure

TABLE: Steel Design 1 - Summary Data - AISC 360-16

Frame DesignSect DesignType Status Ratio RatioType Combo
Text Text Text Text Unitless Text Text
16 RHCF100X50X3 Column No Messages 0.129142 PMM 0.9DL+WL
14 RHCF100X50X3 Column No Messages 0.188694 PMM 0.9DL+WL
15 RHCF100X50X3 Beam No Messages 0.395548 PMM 0.9DL+WL
17 RHCF100X50X3 Beam No Messages 0.558887 PMM 0.9DL+WL
19 RHCF100X50X3 Column No Messages 0.191051 PMM 0.9DL+WL
21 RHCF100X50X3 Column No Messages 0.187593 PMM 0.9DL+WL
23 RHCF100X50X3 Column No Messages 0.103143 PMM 0.9DL+WL
25 RHCF100X50X3 Column No Messages 0.123377 PMM 0.9DL+WL
27 RHCF100X50X3 Column No Messages 0.213208 PMM 0.9DL+WL
31 RHCF100X50X3 Beam No Messages 0.224652 PMM 0.9DL+WL
32 RHCF100X50X3 Beam No Messages 0.243522 PMM 0.9DL+WL
33 RHCF100X50X3 Beam No Messages 0.21678 PMM 0.9DL+WL
34 RHCF100X50X3 Beam No Messages 0.047572 PMM 0.9DL+WL
42 RHCF100X50X3 Beam No Messages 0.120538 PMM 0.9DL+WL
50 SHCF 30X30X2 Column No Messages 0.065985 PMM 0.9DL+WL
51 SHCF 30X30X2 Column No Messages 0.056748 PMM 0.9DL+WL
52 SHCF 30X30X2 Column No Messages 0.073827 PMM 0.9DL+WL
53 SHCF 30X30X2 Column No Messages 0.057748 PMM 0.9DL+WL
54 SHCF 30X30X2 Column No Messages 0.081831 PMM 0.9DL+WL
55 SHCF 30X30X2 Column No Messages 0.058417 PMM 0.9DL+WL
56 SHCF 30X30X2 Column No Messages 0.089297 PMM 0.9DL+WL
57 SHCF 30X30X2 Column No Messages 0.059225 PMM 0.9DL+WL
58 SHCF 30X30X2 Column No Messages 0.095649 PMM 0.9DL+WL
59 SHCF 30X30X2 Column No Messages 0.061551 PMM 0.9DL+WL
60 SHCF 30X30X2 Column No Messages 0.099812 PMM 0.9DL+WL
61 SHCF 30X30X2 Column No Messages 0.069493 PMM 0.9DL+WL
62 SHCF 30X30X2 Column No Messages 0.100447 PMM 0.9DL+WL
63 SHCF 30X30X2 Column No Messages 0.077647 PMM 0.9DL+WL
71 RHCF100X50X3 Beam No Messages 0.159088 PMM 0.9DL+WL
79 SHCF 30X30X2 Column No Messages 0.105347 PMM 0.9DL+WL
80 SHCF 30X30X2 Column No Messages 0.109299 PMM 0.9DL+WL
81 SHCF 30X30X2 Column No Messages 0.111201 PMM 0.9DL+WL
82 SHCF 30X30X2 Column No Messages 0.136083 PMM 0.9DL+WL
83 SHCF 30X30X2 Column No Messages 0.110963 PMM 0.9DL+WL
84 SHCF 30X30X2 Column No Messages 0.142726 PMM 0.9DL+WL
85 SHCF 30X30X2 Column No Messages 0.105301 PMM 0.9DL+WL
86 SHCF 30X30X2 Column No Messages 0.136123 PMM 0.9DL+WL
87 SHCF 30X30X2 Column No Messages 0.09641 PMM 0.9DL+WL
88 SHCF 30X30X2 Column No Messages 0.126212 PMM 0.9DL+WL
89 SHCF 30X30X2 Column No Messages 0.087323 PMM 0.9DL+WL
90 SHCF 30X30X2 Column No Messages 0.114995 PMM 0.9DL+WL
Design of Steel Structure

91 SHCF 30X30X2 Column No Messages 0.079893 PMM 0.9DL+WL

92 SHCF 30X30X2 Column No Messages 0.101646 PMM 0.9DL+WL
93 SHCF 30X30X2 Column No Messages 0.071596 PMM 0.9DL+WL
94 SHCF 30X30X2 Column No Messages 0.083995 PMM 0.9DL+WL
95 SHCF 30X30X2 Column No Messages 0.065755 PMM 0.9DL+WL
96 SHCF 30X30X2 Column No Messages 0.07976 PMM 0.9DL+WL
97 SHCF 30X30X2 Column No Messages 0.059138 PMM 0.9DL+WL
98 SHCF 30X30X2 Column No Messages 0.074387 PMM 0.9DL+WL
99 SHCF 30X30X2 Column No Messages 0.052885 PMM 0.9DL+WL
100 SHCF 30X30X2 Column No Messages 0.068486 PMM 0.9DL+WL
101 SHCF 30X30X2 Column No Messages 0.050797 PMM 0.9DL+WL
102 SHCF 30X30X2 Column No Messages 0.062244 PMM 0.9DL+WL
103 SHCF 30X30X2 Column No Messages 0.049644 PMM 0.9DL+WL
104 SHCF 30X30X2 Column No Messages 0.055997 PMM 0.9DL+WL
105 SHCF 30X30X2 Column No Messages 0.048484 PMM 0.9DL+WL
106 SHCF 30X30X2 Column No Messages 0.049614 PMM 0.9DL+WL
107 SHCF 30X30X2 Column No Messages 0.048142 PMM 0.9DL+WL
108 SHCF 30X30X2 Column No Messages 0.041809 PMM 0.9DL+WL
109 SHCF 30X30X2 Column No Messages 0.048097 PMM 0.9DL+WL
110 SHCF 30X30X2 Column No Messages 0.041588 PMM 0.9DL+WL
111 SHCF 30X30X2 Column No Messages 0.048013 PMM 0.9DL+WL
112 SHCF 30X30X2 Column No Messages 0.041386 PMM 0.9DL+WL
113 SHCF 30X30X2 Column No Messages 0.048273 PMM 0.9DL+WL
114 SHCF 30X30X2 Column No Messages 0.042403 PMM 0.9DL+WL
115 SHCF 30X30X2 Column No Messages 0.048826 PMM 0.9DL+WL
116 SHCF 30X30X2 Column No Messages 0.045732 PMM 0.9DL+WL
117 SHCF 30X30X2 Column No Messages 0.049753 PMM 0.9DL+WL
118 SHCF 30X30X2 Column No Messages 0.049127 PMM 0.9DL+WL
119 SHCF 30X30X2 Column No Messages 0.050544 PMM 0.9DL+WL
120 SHCF 30X30X2 Column No Messages 0.05208 PMM 0.9DL+WL
121 SHCF 30X30X2 Column No Messages 0.051774 PMM 0.9DL+WL
122 SHCF 30X30X2 Column No Messages 0.066541 PMM 0.9DL+WL
123 SHCF 30X30X2 Column No Messages 0.053167 PMM 0.9DL+WL
124 SHCF 30X30X2 Column No Messages 0.077533 PMM 0.9DL+WL
125 SHCF 30X30X2 Column No Messages 0.054489 PMM 0.9DL+WL
126 SHCF 30X30X2 Column No Messages 0.087634 PMM 0.9DL+WL
127 SHCF 30X30X2 Column No Messages 0.05576 PMM 0.9DL+WL
128 SHCF 30X30X2 Column No Messages 0.09687 PMM 0.9DL+WL
129 SHCF 30X30X2 Column No Messages 0.056836 PMM 0.9DL+WL
130 SHCF 30X30X2 Column No Messages 0.104018 PMM 0.9DL+WL
131 SHCF 30X30X2 Column No Messages 0.059347 PMM 0.9DL+WL
132 SHCF 30X30X2 Column No Messages 0.108131 PMM 0.9DL+WL
133 SHCF 30X30X2 Column No Messages 0.06474 PMM 0.9DL+WL
134 SHCF 30X30X2 Column No Messages 0.107558 PMM 0.9DL+WL
Design of Steel Structure

135 SHCF 30X30X2 Column No Messages 0.06535 PMM 0.9DL+WL

136 SHCF 30X30X2 Column No Messages 0.125079 PMM 0.9DL+WL
137 SHCF 30X30X2 Column No Messages 0.066404 PMM 0.9DL+WL
138 SHCF 30X30X2 Column No Messages 0.133376 PMM 0.9DL+WL
139 SHCF 30X30X2 Column No Messages 0.066153 PMM 0.9DL+WL
140 SHCF 30X30X2 Column No Messages 0.112336 PMM 0.9DL+WL
141 SHCF 30X30X2 Column No Messages 0.065743 PMM 0.9DL+WL
142 SHCF 30X30X2 Column No Messages 0.079535 PMM 0.9DL+WL
143 SHCF 30X30X2 Column No Messages 0.070927 PMM 0.9DL+WL
144 SHCF 30X30X2 Column No Messages 0.060645 PMM 0.9DL+WL
145 SHCF 30X30X2 Column No Messages 0.078484 PMM 0.9DL+WL
146 SHCF 30X30X2 Column No Messages 0.059193 PMM 0.9DL+WL
147 SHCF 30X30X2 Column No Messages 0.087006 PMM 0.9DL+WL
148 SHCF 30X30X2 Column No Messages 0.06023 PMM 0.9DL+WL
Design of Steel Structure

6- Structural Analysis, Design and Results

6.4 - Deflection Check

18
Design of Steel Structure

6- Structural Analysis, Design and Results

6.4 - Deflection Check

Max. Displacement is 37.5mm which is lesser than L/120= 6000/120 =50.0mm(hence, ok)

STRUCTURAL DESIGN

TABLE 1604.3 1604.4 Analysis. Load effects on structural members and their
DEFLECTION
connections shall be determined by methods of structural anal¬
CONSTRUCTION L Sot W' 0+1*4 ysis that take into account equilibrium, general stability, geo¬
metric compatibility and both short- and long-term material
Roof members:*
Supporting plaster ceiling //360 //360 //240 properties.
Supporting nonplaster ceiling //240 //240 //180 Members that tend to accumulate residual deformations
Not supporting ceiling //180 //180 //120 under repeated service loads shall have included in their analy¬
Floor members
Exterior walls and interior
//360
— //240
sis the added eccentricities expected to occur during their ser¬
vice life.
Any system or method of construction to be used shall be
partitions:
With brittle finishes
With flexible finishes
— //240
//120
— based on a rational analysis in accotdance with well-established
principles of mechanics. Such analysis shall result in a system
that provides a complete load path capable of transferring loads
Farm buildings — — //180 from their point of origin to the load-resisting elements.
Greenhouses — — //120 The total lateral force shall be distributed to the various verti¬
cal elements of the lateral-force-resisting system in proportion

19
SLIDING GATE.sdb

Z
Y
X

-7.0 -3.5 0.0 3.5 7.0 10.5 14.0 17.5 21.0 24.5 28.0 31.5 35.0 38.5 E-3
SAP2000 24.0.0 Deformed Shape (0.6WIND) - Contours for Uy KN, m, C
Design of Steel Structure

6- Structural Analysis, Design and Results

6.5 - Design Connection

18
Design of Steel Structure

6- Structural Analysis, Design and Results

6.5- Design Connections .

6.5-1 - Typical weld Design for SHS30x30x2

6.5-2 - Typical weld Design for RHS100x50x3

Project:
Project no:
Author:

Project data
Project name
Project number
Author
Description
Date 7/3/2024
Design code AISC 360-10

Material
Steel S275

1 / 10
Project:
Project no:
Author:

Project item CON1

Design
Name CON1
Description
Analysis Stress, strain/ simplified loading
Design code AISC - LRFD 2010

Beams and columns

β – Direction γ - Pitch α - Rotation Offset ex Offset ey Offset ez
Name Cross-section Forces in
[°] [°] [°] [mm] [mm] [mm]
C 4 - RHSCF100/50/3.0 0.0 -90.0 0.0 -30 0 0 Node
B 5 - SHSCF(Hy)25/25/2.0 0.0 0.0 0.0 0 0 0 Node

Cross-sections
Name Material
4 - RHSCF100/50/3.0 S275
5 - SHSCF(Hy)25/25/2.0 S275

2 / 10
Project:
Project no:
Author:

Load effects (equilibrium not required)

N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B 0.2 0.0 0.0 0.0 0.0 0.0
LE2 B -1.1 0.0 0.0 0.0 0.0 0.0
LE3 B -0.2 0.0 0.0 0.0 0.0 0.0
LE4 B 0.0 0.0 0.0 0.0 0.0 0.0
LE5 B -0.1 0.0 0.0 0.0 0.0 0.0

Check

Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Welds 31.9 < 100% OK
Buckling Not calculated
GMNA Calculated

Plates
fy Thickness σEd εPl σcEd
Name Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
C 248.2 3.0 LE5 41.2 0.0 0.0 OK
B 248.2 2.0 LE2 45.4 0.0 0.0 OK

Design data

fy εlim
Material
[MPa] [%]
S275 248.2 5.0

Symbol explanation
εPl Plastic strain
σcEd Contact stress
σEd Eq. stress
fy Yield strength
εlim Limit of plastic strain

3 / 10
 Project:
Project no:
Author:

Overall check, LE5

Strain check, LE5

4 / 10
 Project:
Project no:
Author:

Equivalent stress, LE5

Weld sections
Th Ls L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
C-w 1 B E70xx ◢1.4 ◢2.0 83 3 LE2 0.4 1.2 31.9 OK

Symbol explanation
Th Throat thickness of weld
Ls Leg size of weld
L Length of weld
Lc Length of weld critical element
Fn Force in weld critical element
ϕRn Weld resistance AISC 360-16 J2.4
Ut Utilization

Buckling
Buckling analysis was not calculated.

5 / 10
Project:
Project no:
Author:

Project item CON2

Design
Name CON2
Description
Analysis Stress, strain/ simplified loading
Design code AISC - LRFD 2010

Beams and columns

β – Direction γ - Pitch α - Rotation Offset ex Offset ey Offset ez
Name Cross-section Forces in
[°] [°] [°] [mm] [mm] [mm]
C 4 - RHSCF100/50/3.0 0.0 -90.0 0.0 -30 0 0 Node
B 4 - RHSCF100/50/3.0 0.0 0.0 0.0 0 0 0 Node

Cross-sections
Name Material
4 - RHSCF100/50/3.0 S275

6 / 10
Project:
Project no:
Author:

Load effects (equilibrium not required)

N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
LE1 B 0.2 0.0 0.0 0.0 0.0 0.0
LE2 B -0.6 0.0 -0.3 0.0 0.3 0.0
LE3 B 0.0 0.0 1.2 0.0 -0.1 0.0
LE4 B 0.0 0.0 -1.3 0.0 0.2 0.0
LE5 B 0.0 0.0 -1.3 0.0 0.4 0.0
LE6 B 0.0 0.0 1.2 0.0 -0.4 0.0
LE7 B -0.4 0.7 -0.2 -0.2 0.2 -0.2
LE8 B 0.0 0.1 -0.3 0.5 -0.1 0.1
LE9 B 0.0 0.0 0.0 -0.1 0.1 0.9
LE10 B 0.0 -0.4 0.3 -0.4 -0.1 -0.6

Check

Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.0 < 5.0% OK
Welds 75.5 < 100% OK
Buckling Not calculated
GMNA Calculated

Plates
fy Thickness σEd εPl σcEd
Name Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
C 248.2 3.0 LE9 223.5 0.0 0.0 OK
B 248.2 3.0 LE9 174.4 0.0 0.0 OK

Design data

fy εlim
Material
[MPa] [%]
S275 248.2 5.0

Symbol explanation
εPl Plastic strain
σcEd Contact stress
σEd Eq. stress
fy Yield strength
εlim Limit of plastic strain

7 / 10
 Project:
Project no:
Author:

Overall check, LE9

Strain check, LE9

8 / 10
 Project:
Project no:
Author:

Equivalent stress, LE9

Weld sections
Th Ls L Lc Fn ϕRn Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
C-w 1 B E70xx ◢2.1 ◢3.0 276 3 LE9 1.6 2.1 75.5 OK

Symbol explanation
Th Throat thickness of weld
Ls Leg size of weld
L Length of weld
Lc Length of weld critical element
Fn Force in weld critical element
ϕRn Weld resistance AISC 360-16 J2.4
Ut Utilization

Buckling
Buckling analysis was not calculated.

Code settings
Item Value Unit Reference
Friction coefficient - concrete 0.40 - ACI 349 – B.6.1.4
Friction coefficient in slip-resistance 0.30 - AISC 360-10 J3.8
Limit plastic strain 0.05 -

9 / 10
Project:
Project no:
Author:

Item Value Unit Reference

Plastic
Weld stress evaluation
redistribution
Detailing No
Distance between bolts [d] 2.66 - AISC 360-10 – J3.3
Distance between bolts and edge [d] 1.25 - AISC 360-10 – J.3.4
Concrete breakout resistance check Both
Base metal capacity check at weld fusion
No AISC 360-10: J2-2
face
Cracked concrete Yes ACI 318-14 – Chapter 17
Local deformation check No
Local deformation limit 0.03 - CIDECT DG 1, 3 - 1.1
Analysis with large deformations for hollow section
Geometrical nonlinearity (GMNA) Yes
joints

10 / 10
Design of Steel Structure

7- Conclusion

Therefore, the sliding steel gate support frame design sections is

adequate and safe to support the design load applied and in compliance with the code .

8- Reference Plan and Section Details

45
 12 11 10 9 8 7 6 5 4 3 2 1
This drawing is the property of Larsen & Toubro Construction and must not be passed on to any person or body not
authorised by us to receive it nor be copied or otherwise made use either in full or in part by such person or body without
PROTECTIVE TREATEMENT: our prior permission in writing
1. PROTECTIVE TREATMENT - ALL MS STEEL ITEMS WILL BE
GALVANIZED + EPOXY COATED TO QCS2014 AND PAINT
MANUFACTURER RECOMENDATION ie
· 2 COAT PRIMER(250µm)
· 1 COAT TOP COAT(50µm)-RAL 9005 (BLACK)
· TOTAL=300µm N THIS AREA

INFILL (30x30x2mm SHS )

H GATE FRAME (100x50x3mm SHS H

EXISTING WALL
EXISTING COLUMN
A

GATE BRACE (100x50x3mm SHS)

KEYPLAN:
NOTES:
1. ALL LEVELS SHOWN IN THE DRAWINGS ARE QND LEVELS
2. ALL DIMENSIONS ARE IN MILLIMETERS (mm)
3. ALL STRUCTURAL SHOP DRAWINGS TO BE READ IN CONJUNCTION
WITH ALL OTHER RELEVANT DISCIPLINE SUCH AS
G ARCHITECTURAL AND CIVIL. G
4. CONCRETE GRADE AS C40 OPC PER PROJECT SPECIFICATION.
4. PROTECTIVE TREATMENT - ALL MS STEEL ITEMS WILL BE
GALVANIZED + EPOXY COATED TO QCS2014

F F

FGL- +20.00 FGL- +20.00

LEGENDS:

A
6M OPENINING SINGLE
LEAF SLIDING GATE
E E
EXISTING WALL EXISTING WALL COLUMN
EXISTING WALL COLUMN HOLD LIST:

REFERENCE DRAWINGS:
DRAWING NO. DRAWING TITLE

TOP PLAN VIEW

D
D

GATE FRAME
100X50X3MM RHS
00 DD/MM/YY FOR INFORMATION ONLY XX XX XX

GATE BRACING REV. DATE DESCRIPTION DRAWN CHECKED APPROVED

CLIENT/
ENGINEER

100X50X3MM RHS CLIENT

STATE OF QATAR
C
4 X M12 SS ANCHORS PUBLIC WORKS AUTHORITY
C
PROJECTS AFFAIRS
WITH 10MM THICK PLATE INFILL 30X30X2MM SHS P.O. BOX 22188, DOHA, QATAR
TEL: +974 4495 0000, FAX: +974 4495 0900
CONSULTANT

EGIS INTERNATIONAL
DETAIL-3 P.O. BOX 20690, DOHA, QATAR
TEL: +974 4016 3133, FAX: +974 4417 3629

MAIN CONTRACTOR
EXISTING WALL LARSEN & TOUBRO LIMITED
WATER & EFFLUENT TREATMENT IC
WATER INTERNATIONAL BU
GATE FRAME P.O. BOX 24399, DOHA, QATAR
B ROLLER /GUIDE TEL: +974 4423 9000, FAX: +974 4455 1286
SUB CONTRACTOR B
NYLON WHEEL National Engineering & Construction Company WLL
GATE WHEEL P.O.BOX-17211, Doha - Qatar
Tel : +974-4-4434852 Fax : +974-4-4361475
Email : [email protected] / admin @ necodoha.com

100X100X3MM Website: www.necodoha.com

10MM Ø 8 BARS 8MMØ300MMSTIRRUPS

SHS SUPPORT PROJECT
@150MM C/C DESIGN, BUILD, OPERATE AND

25MM ROUND BAR 100X50X3MM 25MM MS ROUND BAR

MAINTAIN (DBOM) CONTRACT FOR
30X30X3MM SS INTEGRATED INDUSTRIAL
SHS GATE FRAME
WELDED WITH
50X5MM FLAT BAR
FLAT BAR@1200MM C/C
DETAIL-1 WELDED WITH 50X5MM WASTEWATER TREATMENT WORKS
(IIWWTW) PHASE I
MS FLAT BAR 30X30X3MM SS CIVIL PROJECT ID : CP 798
A PROJECT CODE : IA 14/15 C 133 G R2
2 COAT OF BITUMIN FLAT BAR(100MM A
TITLE
LONG)@1200MM C/C 6M WIDTH & 3.5M HEIGH SLIDING
SECTION-AA GATE ELEVATION & DETAILS
DETAIL-2 DRAWING NO: SIZE: A1 SCALE: SCALE
NEC-933-AR-SD-001 SHEET-NO-1
12 11 10 9 8 7 6 5 4 3 2 1