designfeature

28 Power Electronics Technology | November 2010 www.powerelectronics.com

A
nother Isolated Bridgeless PFC converter (patents pending) with pul-
sating input current and based on a novel Hybrid-switching method
eliminates the front-end full-bridge rectifier, yet provides isolation
in a Single-stage power processing, resulting in performance, size,
and cost advantages over conventional Three- stage, bridge-type PFC
converters.
The single-stage isolated bridgeless PFC Converter with pulsating
input current attains improved efficiency of over 98% (achievable with appropriate
switching devices) compared to 89% of the Three-stage approach, offering simultane-
ously significant size and cost reductions, while maintaining the near unity power fac-
tor of 0.999 and 1.7% total harmonic distortion. The single-stage converter uses just
a single magnetic part (the isolation transformer) and three switches, compared with
compared to four magnetic pieces and 14-switches of the conventional Three-stage
approach. This pulsating version requires only a single resonant capacitor and no input
inductor, when compared to the Isolated Bridgeless Converter presented in October
2010 issue of Power Electronics Technology.
The new non-isolated Bridgeless PFC converter with pulsating input current of
Fig. 1a operates directly of the ac line and without the need for a Full-Bridge recti-
fier in front. Despite the use of a resonant inductor and a resonant capacitor, thanks
to the novel hybrid-switching method, the DC voltage gain
depends on the duty ratio only and NOT on resonant compo-
nent values or the load current. Furthermore, the converters
DC voltage gain is the same for either positive input voltage
or negative input voltage. Hence, it provides automatic ac
line rectification, without the need for a bridge rectifier.
Although the converter topology resembles that of con-
ventional flyback converter, its voltage gain characteristics in
the operating step-up region is entirely different and not the
flyback converter type with DC voltage gain of D/ (1-D),
but instead of the boost converter type with DC voltage gain
1/(1-D).
The isolated version of the converter is obtained simply
A Single-stage Isolated
Bridgeless PFC Converter
(patents pending) has a single
isolation transformer, three
switches, and 98% efficiency
compared to four magnetic
pieces, 14 switches, and 89%
efficiency of the conventional
Three-stage approach. It
achieves best in-class PFC
performance with 0.999
power factor and 1.7% total
harmonic distortion.
Dr. SloboDan Cuk, President, TESLAco
Single-Stage Isolated Bridgeless PFC
Converter Achieves 98% Efficiency
11_Cuk_F1a
C
C
r S
(a)
L
+

Lr
CR
2
i
L
I
r
CR
1
V
R
I
v
AC
CR
1
+

CR
2
S
C
V
R
C
r L
v
AC
L
r f
C
f N
P
N
S
i
AC
Bridgeless PFC IC Controller
(b)
t
i
AC
i
AC
v
AC
v ,
AC
(c)
Fig. 1(a) Operating directly from the ac line, this converter operates is the second
true single-stage bridgeless ac-dc converter with PFC. It has one controlling
switch and two diode switches, and in addition to a PWM inductor a small resonant
inductor and small resonant capacitor. (b) The new Isolated Bridgeless PFC con-
verter and Bridgeless PFC IC controller operates by sensing directly the full-wave
AC line voltage and AC line currents and controlling switch S. (c) The switch S is
controlled by the Bridgeless PFC IC controller, so as to force the line current to be
proportional to the sinusoidal line voltage and in phase with it.
011PETCuk.indd 28 11/4/10 10:47:47 AM
www.powerelectronics.com November 2010 | Power Electronics Technology 29
by replacing replacing a single inductance L in converter
of Fig. 1a with a two-winding isolation transformer with
NP:NS turns ratio, as illustrated in the Single-Stage Isolated
Bridgeless PFC converter Fig. 1b. The duty ratio control
of the power stage with the help of Bridgeless PFC IC
Controller and high frequency input filter shown in Fig.
1b results in clean sinusoidal input current drawn in phase
with sinusoidal input line voltage and proportional to it,
resulting in unity power factor. The measured power factor
on experimental 400W prototype was 0.999 for 110V ac,
60Hz line.
Bridgeless PFC CoNverter oPeratioN
A very clear objective to increase the efficiency is to devise a
converter, which can eliminate a front-end full-bridge recti-
fier. Past attempts failed to eliminate diode-bridge rectifiers,
leading to the belief that the solution to such a goal may
be impossible and that such converter topology could not
exist. This is shown to be no longer the case as the July and
August issues of Power Electronics Technology demonstrated a
non-isolated True Bridgeless PFC converter and the October
issue introduced an Isolated Bridgeless PFC converter based
on it. Here, another True Bridgeless PFC converter topol-
ogy (non-isolated and isolated ones ) is introduced which is
even simpler, such as the pulsating input current converter
topology of Fig. 1a.
This converter topology comprises only three switches:
one controllable switch S and two passive current rectifier
switches CR1 and CR2 as seen in Fig. 1a, which turn-ON
and turn-OFF in response to the state of the main control-
ling switch S for either positive or negative polarity of the
input ac voltage.
Thus, switch S alone controls both diode switches, whose
states are changed automatically according to the polarity of
BRIDGELESS pfcconverter
11_Cuk_F2a
C
C
r S
D
L
+

+
+

Lr
CR
2
CR
1
V
R
I
V
g
V
Cr
+

(a)
C
C
r
+ +

+
V
R
I
V
g
V
V
Cr
+

(b)
C
C
r
L
+
+

+
V
R
I
V
V
g
V
g
V
Cr
V
Cr
+
+

(c)
11_Cuk_F3a
C
C
r S
D
D
D'
A
G
L
+

+
+

Lr I
S
CR
2
CR
1
V
R
I
I
r
I
L
V
g
V
Cr
+

(a)
t
OFF ON
CR
2
t
D'T
S
DT
S
ON OFF
S, CR
1
(b)
C
r
C
V
g
+

L
r
V
R
+
V
Cr
I
+

L
I
ON
(c)
C
r
C
V
g
+

L
r
V
R
+
V
Cr
I
+

L
(d)
D
1
VS/V, V
CR1
/V, V
CR2
/V
(d)
Fig. 2 (a) shows the operation from a positive half-cycle of sinusoidal ac line voltage is shown by this dC-dC converter. (b) the
equivalent circuit model for oN-time interval. (c) the equivalent circuit model for the oFF-time interval. (d) the voltage stresses of three switches.
Fig. 3. Bridgeless PFC converter operation for positive half-cycle of input voltage. (a) switch s operates in phase with diode Cr1 and out of phase with diode Cr2. (b)
states of the switches of PFC converter (c) linear switched networks for oN-time interval (d) linear switched network for oFF-time interval
011PETCuk.indd 29 11/4/10 10:47:49 AM
30 Power Electronics Technology | November 2010 www.powerelectronics.com
the ac input voltage. For example, for the positive polarity of
the ac input voltage, current rectifier CR1 conducts during
the ON-time interval of switch S. Then, for negative polar-
ity of ac input voltage, the same current rectifier CR1 con-
ducts during the OFF-time interval of switch S. The current
rectifier CR2 also responds automatically to the state of the
switch S and polarity of the input ac voltage. For the positive
polarity it conducts during the OFF-time interval of switch
S and for negative polarity, it conducts during the ON-time
interval of switch S.
Thus, the three switches operate at all times, for both
positive and negative half-cycles of the input ac line voltage.
Hence, this true Bridgeless PFC converter
TM
operates with-
out the full-bridge rectifier, since the converter topology
itself performs an implied ac line rectification to result in
DC output voltage for either polarity of input ac line volt-
age. Eliminating the full-bridge rectifier directly eliminates
large losses, especially for the low line of 85V.
As seen in Fig. 1a, this topology also consists of the float-
ing energy transferring capacitor Cr, which acts as a resonant
capacitor for the part of the switching cycle, and a resonant
inductor Lr and an isolation transformer.
Voltage StreSSeS of the SwitcheS
The AC-DC converter shown in Fig. 1a when operated
from a positive half-cycle of sinusoidal ac line voltage is well
represented with a DC-DC converter shown in Fig. 2a. The
corresponding converter models for ON-time interval (Fig.
2b) and for OFF-time interval (Fig. 2c) directly result in the
voltage stresses of three switches as:
V
CR1
= V
CR2
= V
S
= V (1)
where V is the output DC voltage, since from Fig. 2a:
V
g
+ V
Cr
= V (2)
The relationship (1) is graphically shown on Fig. 2d as a
straight line with relative gain of 1, to illustrate the impor-
tant advantage of this topology that all three switches have
for any operating duty ratio the same voltage stress equal
to the output voltage V. This should be, for example, com-
pared with the voltage stresses for the flyback converter.
Although the flyback converter has two switches only, each
of the switches has at 50% duty ratio the voltage stress equal
to twice the output DC voltage.
Therefore, if the flyback converter were used for an
AC-DC converter with V=400V output, it would need
switches rated at 1200V, as opposed to 600V rated switches
in the converter of Fig. 1a. However, the 1200V rated
BRIDGELESS pfcconverter
t
v
L
(t)
0
V
g
V
Cr
T
ON
T
OFF
0.5T
S
0.5T
S
+

(a)
v
0
Cr
V
Cr
V = D/(1D)
Cr

+v
r
T
ON
+
v
r

(b)
11_Cuk_F5a.ai
I
L
I
p
t
T
OFF
T
ON
i
Cr
(t)

+
(a)
i
TT
OFF
(t) v
Cr
V
Cr
V
Cr

t
+v
r
TT
ON
v
r
(b)
fig. 4. PwM inductor l is excited as in PwM converters with a square-wave like voltage over entire switching period while resonant inductor is excited over the oN-time
interval only: (a) Voltage waveform of the PwM inductor and respective positive flux excursions (shaded area designated with positive sign) and negative flux excur-
sions (shaded area designated with negative sign. (b) resonant inductor lr is excited with a co-sinusoidal ac ripple voltage vr of the resonant capacitor cr and is fully
flux-balanced during only oN-time interval (see respective shaded areas).
fig. 5. resonant inductor current and resonant capacitor voltage waveforms
during the entire switching period (a) resonant inductor current ir during entire
switching period (b) resonant capacitor voltage shows the linear charging of the
resonant capacitor cr during the off-time interval.
011PETCuk.indd 30 11/4/10 10:47:50 AM
www.powerelectronics.com November 2010 | Power Electronics Technology 31
switch (in this case, IXYS IXTH12N1200 switch in
a TO-247 package), exhibits 1.4 ON-resistance and
280pF drain-to-source capacitance. By comparison, the
best-in-class 600V rated device in the same TO-247 pack-
age, the IPW66R037C6 from Infineon, exhibits a 37m
ON-resistance and 130pF drain-to-source capacitance.
Note that this configuration achieves almost a 40 times
a reduction in ON-resistance and corresponding reduced
conduction losses, and more than 2 times reduced drain-to-
source capacitance for reduced switching losses as well. This
clearly makes the flyback converter much less efficient than
the new converter topology of Fig. 1a. When it is also rec-
ognized that the conventional flyback converter cannot be
used without front-end bridge rectifier for AC-DC conver-
sion, the efficiency gap becomes even much bigger.
DetaileD aNalysis
Operation from Positive Input Voltage
First, we analyze the operation of the converter in Fig. 3a
in which the input voltage source is positive dc voltage and
having the switch states as in Fig. 3b. The linear switched
network for ON-time interval is shown in Fig. 3c and linear
switched network for OFF-time interval is shown in Fig. 3d.
To simplify the analysis, we will assume that the inductor L
is very large, resulting in a constant input dc current I with
negligible ac ripple current.
Flux Balance of Two Inductors and DC Voltage Gain
The Volt-second (flux balance) on inductor L requires
that for the steady-state, the positive and negative areas of
the voltage waveform in Fig. 4a must be equal so that:
V
g
DT
S
= V
Cr
(1D)T
S
(3)
where:
V
g
= input voltage
D = Duty ratio
T
s
= Switching period in seconds
V
Cr
= DC voltage on the resonant capacitor
Unlike the PWM inductor, L, which was flux balanced
over the entire switching period Ts, the resonant inductor
Lr must be fully flux balanced during the ON-time interval
only as seen in Fig. 4b. Thus applying the steady-state crite-
ria for the resonant inductor Lr in the loop consisting of Vg,
Cr, Lr and V results in:
Vg + V
Cr
-V = 0 (4)
as the resonant inductor must be flux-balanced and cannot
support any net DC voltage.
Solving (3) and (4) results in;
V
Cr
= V
g
D / (1-D) (5)
V = V
g
1/ (1-D) (6)
Note that the dc conversion ratio given by Equation (6)
is the same as for well-known boost converter. Furthermore,
despite the resonant circuit consisting of resonant capacitor
Cr and resonant inductor Lr, and corresponding sinusoidal
and co-sinusoidal time domain waveforms of resonant cur-
rent and resonant capacitor voltage, the dc conversion ratio
does not depend on either one of them and their values or
the switching period T
s
, but only depends on the operating
duty ratio, D, as in conventional PWM dc-dc converters.
Hence, the regular duty ratio control can be employed to
use this converter as a basis for PFC control as in boost and
other conventional converters.
The resonant inductor current ir during entire switch-
ing period is shown in Fig. 5a, while the resonant capacitor
voltage shown in Fig. 5b displays the linear charging of the
resonant capacitor Cr during the OFF-time interval. Note
also the continuity of the capacitor voltage at the transition
between two switching intervals.
BRIDGELESS PFCconverter
11_Cuk_F6a
C
C
r
S
D
D
D'
A
G
L
+

+
+

Lr I
S
CR
2
CR
1
V
R
I
I
r
I
L V
g
V
Cr
+

(a)
t
OFF ON
CR
1
t
D'T
S
DT
S
ON OFF
S, CR
2
(b)
C
r
C
V
g
+

L
r
V
R
+
V
Cr
I
+

L
I
ON
(c)
C
r
C
V
g
+

L
r
V
R
+
V
Cr
I
+
L
(d)
Fig. 6. Bridgeless PFC converter operation for negative half-cycle of input voltage: (a) switch s operates in phase with diode CR2 and out of phase with diode CR1. (b)
states of the switches of PFC converter (c) linear switched networks for ON-time interval (d) linear switched network for OFF-time interval
011PETCuk.indd 31 11/4/10 10:47:51 AM
32 Power Electronics Technology | November 2010 www.powerelectronics.com
Operation from Negative Input Voltage
Next, we analyze the operation of the converter in Fig.
6a, in which the input voltage source is negative polarity
dc voltage and having the switch states as in Fig. 6b. Fig. 6c
shows the linear switched networks for ON-time interval,
while Fig. 6d shows the linear switched network for the
OFF-time interval.
Flux (Volt-second) Balance of Two Inductors and DC volt-
age Gain
We now use the two linear switched networks in Fig. 6c
and Fig. 6d to construct the time domain of the current in
the PWM inductor L and in the resonant inductor Lr. The
voltage waveform on inductor L is shown in Fig. 7a to be
just as in conventional PWM square-wave
switching converters, while the resonant
capacitor V
cr
voltage is illustrated in Fig.
7b only for ON-time resonant interval
and its complete time domain waveform
in Fig. 8b.
The Volt-second (flux) balance on
inductor L requires that for the steady-
state, the positive and negative areas of
the voltage waveforms in Fig. 7a must be
equal so that:
V
g
DT
S
= (V - V
Cr

) (1D)T
S
(7)
Unlike the PWM inductor, which was flux balanced over
the entire period T
s
, the resonant inductor must be fully
flux-balanced during the ON-time interval only as per con-
verter model of Fig. 6c, in which the loop consisting of Vg,
Cr, and Lr forms the resonant circuit model. From which:
Vg - V
Cr
= 0 (8)
Solving (7) and (8) results in:
V
Cr
= Vg (9)
V = Vg 1/ (1-D) (10)
Therefore, despite different DC voltages on the resonant
capacitor Cr for positive input voltage (D/ (1-D)) and for
negative input voltage (input DC voltage Vg), the DC con-
version ratios are identical for positive
and negative polarity input voltages as
shown by (6) and (10).
As before, the resonant current ir
charging capacitor Cr is limited to only
a positive cycle of resonant current as
current rectifier CR2 now permits con-
duction in only one direction as in Fig.
8a. As the resonant current starts at zero
level, this effectively restricts the reso-
BRIDGELESS pFCconverter
11_Cuk_F8a
I
L
I
p
t
T
OFF
T
ON
i
Cr
(t)

+
(a)
C
r
+

V
Cr
i
r
L
r
TT
OFF
(t) v
Cr
V
g

t
+v
r
TT
ON
v
r
(b)
11_Cuk_F7a
t
v
L
V
g
T
ON
T
OFF
DT
S S
D'T
V V
Cr
+

(a)
V
g
0
Cr

(t)
t
+v
r
T
ON
T
OFF
+
v
r

(b)
Fig. 7. PWM inductor L is excited as in PWM converters with a square-wave like
voltage over entire switching period while resonant inductor Lr is excited over the
ON-time interval only: (a) Voltage waveform of the PWM inductor and respective
positive flux excursions (shaded area designated with positive sign) and negative
flux excursion (shaded area designated with negative sign) (b) Resonant inductor
Lr is excited with a co-sinusoidal ac ripple voltage vr of the resonant capacitor
Cr and is fully flux-balanced during only ON-time interval (see respective shaded
areas).
Fig. 8. Resonant inductor current and resonant capacitor voltage waveforms
(a) Resonant inductor current ir during entire switching period (b) Resonant
capacitor voltage shows the linear discharge of the resonant capacitor Cr during
the OFF-time interval.
Fig. 9. Resonant circuit model for both positive
and negative half-cycle of line voltage.
011PETCuk.indd 32 11/4/10 10:47:52 AM
www.powerelectronics.com November 2010 | Power Electronics Technology 33
nant charge interval once again to exactly one-half of the
resonant period, the same as for positive input voltage.
The waveforms over the complete period for resonant
inductor current ir(t) and resonant capacitor voltage vCr(t)
are illustrated in Fig. 8a and Fig. 8b. Note how the continu-
ity of the voltage on resonant capacitor results in the same
ac ripple voltage vr at the transition between two intervals.
Once again, the resonant capacitor dc voltage is now dif-
ferent and equal to dc input voltage Vg. Thus, the same dc
voltage gain is obtained despite drastically different steady-
state values of dc voltage on capacitor Cr The final resonant
circuit model for both positive input voltage and for negative
input voltage are identical and illustrated in Fig. 9.
ResoNaNt CiRCuit aNalysis
As seen above, operation of the converter from positive
input voltage and negative input voltage results in the same
resonant circuit model, which results in the following solu-
tion:
i
r
(t) = I
P
sin(
r
t) (11)
v
Cr
(t) = v
r
cos(
r
t) (12)
v
r
= I
P
R
N
(13)
R
N
= L
r
/C
r
(14)

r
= 1/L
r
C
r
(15)
f
r
=
r
/(2 ) (16)
where RN is the natural resistance, fr is the resonant fre-
quency and r radial frequency.
The Bridgeless PFC converter of Fig. 1a has one control-
ling switch S. From the description of the converter opera-
tion for positive and negative output voltages, it is clear that
this switch S must have a two-quadrant switching charac-
teristic operating in the first and third quadrant as illustrated
in Fig. 10a. In other words, switch S must for positive input
voltage operate in first quadrant, but should also be able
to sustain a full reverse voltage (third quadrant operation).
Clearly, neither bipolar nor MOSFET transistors can do
that as they are not designed to sustain voltage in the third
BRIDGELESS pfcconverter
Easy-to-use module
Auto compensation
Footprint compatibility
Compact size
NDM1-12
NDM1-25
www.novumdigital.com
V-Innitys new 12A and 25 A digital DC-DC Point-of-Load (POL) modules are aimed at the emerging digital
power management and control market. The Novum product line is focused on providing a complete, easy-to
implement solution, with the goal of making the benets of digital power accessible to a wide array of users.
Full featured
PMBus compliant
High effciency
Connect with Us:
011PETCuk.indd 33 11/4/10 10:47:53 AM
34 Power Electronics Technology | November 2010 www.powerelectronics.com
quadrant (MOSFET due to presence of the body diode).
However, the Reverse Blocking Isolated Gate Bipolar
Transistor (RBIGBT) can sustain the full reverse voltage as it
is designed to do so and can sustain the full voltage of oppos-
ing polarity. Therefore, the switch S implementation of Fig.
10b uses two such RBIGBT devices in parallel.
Yet, in many practical applications the MOSFET imple-
mentation is desired due to high switching frequency
capability and low conduction losses. At present, a single
MOSFET implementation is not possible due to built-in
body-diode, so that switch S must be implemented by use
of the two MOSFET devices connected back-to-back in
series as shown in Fig. 11a by using two n-channel MOSFET
devices, S1 and S2, connected at their sources and driven by
a common floating gate drive circuit. Such an implementa-
tion results in full four-quadrant switch capability as shown
in Fig. 11b, which is not required for converter operation as
the two-quadrant of Fig. 10a is sufficient.
It is expected that a single first-third quadrant switch hav-
ing the characteristics of Fig. 10a will be produced as a pla-
nar n-channel MOSFET in which two-quadrant operation
comes naturally from the semiconductor device construc-
tion. This will dramatically reduce the conduction losses of
the switch S by a factor of four times or more, since such
two n-channel devices
could be connected in
parallel and not in series.
As conduction losses are
the converters biggest
losses by far, such a
switch implementation
could push the convert-
ers efficiency over 98%
in the near future.
The current direction
in the resonant inductor
is changing from one
direction in OFF-time
interval to another in
ON-time interval. This
short-duration change could cause the voltage spikes on the
switch S - the faster the change, the larger the voltage spike.
But due to small energy stored in this small inductor, this
spike can be effectively suppressed by use of a Zener diode.
Since the converter operates for both polarities of the input
voltage, a bi-directional Zener diode, called Transorber, is
used to dissipate all of the spike energy and limit the spike
voltage. This, once again would dissipate all of the spike
energy and limit the spike voltage. However, several non-
dissipative ways also can be employed to recover most of
the energy contained and deliver it to the load, thus increas-
ing the efficiency and reducing switch stresses during the
transition.
DC-DC CoNverter CoNtrol
Duty ratio control with constant switching frequency
We now describe one of the possible control methods of
the dc-dc converter in Fig. 3a using the constant switching
frequency and variable duty ratio control. The converter
prototype was built to verify operation and record the char-
acteristic waveforms for three operating duty ratios: D=0.5
(Fig. 12a), D= 0.66 (Fig. 12b) and D= 0.8 (Fig. 12c) result-
ing in output voltages of 18.1V, 28.6V, and 56V respec-
tively, for the 10V input. The measurements were made
at a constant 0.5A
load current. The four
traces show, from top
to bottom: drain-to-
source voltage of the
controlling switch S,
input source current,
output load current
and inductor L cur-
rent.
Note how the input
current (second trace)
consists of the sum of
BRIDGELESS pfcconverter
CR
2
+
+

CR
1
C
V I
R
I
C
r
v
AC
V
Cr
L
r
r
L
D
A
S
1
S
2
I
S
(a)
I
C
S
2
S
1
V
OFF
I
IV
II
III
(b)
Fig. 11. Implementation of the controlling switch S. (a) Implementation of switch S with, two n-channel MoSFets, S1 and S2, connected
back-to-back at their sources and driven by a common floating gate drive circuit. (b) Switch S implementation with two MoSFets
operates in the four-quadrants.
I
ON
S
2
V
OFF
I
III
(a)
CR
2
+
+

CR
1
C
V I
R
I
C
r
v
AC
V
Cr
L
r
r
L
A
S
1
S
2
I
S
(b)
Fig. 10. Implementation of the controlling switch S. (a) Switch S must operate for positive input voltage polarity in first quadrant and
sustain a full reverse voltage in the third quadrant. For negative polarity input voltage, the switch must operate in the third quadrant
but still must be able to sustain a full reverse voltage in the first quadrant. (b) Implementation of switch S with two reverse Blocking
Isolated Gate Bipolar transistors (rBIGBts) connected in parallel.
011PETCuk.indd 34 11/4/10 10:47:54 AM
www.powerelectronics.com November 2010 | Power Electronics Technology 35
resonant inductor Lr current (third trace) and inductor L
current (fourth trace) thus confirming the fundamental
relationships of the converter in Fig. 3a:
i
g
= i
r
+ i
L
(17)
i
0
= i
r
(18)
Note also from (18) that the output current is identical
to the resonant inductor current and therefore it has both
the same shape and duration for all three operating cases
and is therefore not changing, but has the same shape and
magnitude as for 50% duty ratio. Therefore, the input cur-
rent shape and magnitude are changing so that the DC cur-
rent conversion ratio is changed, which ultimately results in
corresponding change in the DC voltage conversion ratios.
This is qualitatively different from the conventional boost
converter operation, in which the high duty ratios result in
shorter duration of the pulse delivery of the load current
(at 0.9 duty ratio it would be 10% of the period). In this
example, the delivery of the load current is always at 50% of
the constant switching period.
In this case, the resonant interval is designed to coincide
with the 50% duty ratio so that the time variation of the
inductor L current at that operating point is hidden and not
explicitly seen (Fig. 12a) as it is in the waveforms of Fig. 12b
and Fig. 12c for duty ratios higher than 50%.
Constant ON-time-interval and variable OFF-time inter-
val control
The converter prototype is then operated with constant
ON-time and variable OFF-time control and the character-
istic waveforms for three effective operating duty ratios are
recorded: D=0.5 (Fig. 13a), D= 0.66 (Fig. 13b) and D= 0.8
(Fig. 13c) resulting in output voltages of 19.3V, 28.8V and
45V, respectively for the 10V input voltage. The measure-
ments were made at a constant 0.5A load current. The four
traces show from top to bottom: drain-to-source voltage of
the controlling switch S, input source current, output load
current and inductor L current.
Note how for higher duty ratios, both input current and
output current are conducting for almost the entire interval,
resulting in quasi-continuous input and output currents. The
output current also has reduced peak values of the resonant
currents and will require minimum output capacitance to
filter this nearly continuous output current.
Two DC-DC ConverTers in one
Voltage gains (6) and (10) derived so far are really represent-
ing dc voltage gain only for the converter in Fig. 3a for the
BRIDGELESS pFCconverter
Spectrum Advanced Specialty Products introduces its
new line of power film capacitors, designed using
the latest film technology to achieve maximum
capacitance density. Available in application-specific
packages and terminations, these new power film
capacitors feature rugged construction to withstand
even the harshest environments.
High ripple currents and voltages up to 20kVDC
Standard capacitance values up to 1000F
Power Film
Capacitors
Call 888.267.1195
or visit SpecEMC.com/film
Fig. 12. Salient waveforms of the converter in Fig. 3a for constant switching frequency and variable duty ratio control a)for duty ratio D=0.5 b)for duty ratio D= 0.66
c)for duty ratio D= 0.8
011PETCuk.indd 35 11/4/10 10:47:55 AM
36 Power Electronics Technology | November 2010 www.powerelectronics.com
BRIDGELESS pfcconverter
duty ratios D higher than the resonant duty ratio DR
that is :
V/Vg = 1/ (1-D) for D > D
R
(19)
D
R
= T
R
/ 2T
S
(20)
T
R
= 1/fr (21)
and (20 and (21) are definitions of the two quantities DR
and T
R
. The voltage conversion ratio for duty ratios lower
than D
R
can be evaluated using the extension of the State-
Space Averaging Method (1,2) introduced in (3) is outside
of the scope of this article. Nevertheless, the following ana-
lytical results is obtained:
V/Vg = D/ (1-D) D
R
for D < D
R
(22)
Note how the DC voltage gain (22) for D=DR changes
into formula for DC conversion given by (19). As DR is
simply a design constant, the overall dc voltage gain of the
converter in Fig. 3a changes form the step-down/step-up
conversion given by (22) for low duty ratios to step-up only
voltage gain given by (19) for higher duty ratios with a con-
tinuous smooth transition at duty ratio DR. This results in
two converters in one, as shown in the composite voltage
gain in Fig. 14.
Therefore the dc-dc converter of Fig. 3a solves two prob-
lems which were plaguing conventional boost and buck-
boost converters:
a) boost converter due to its boost voltage gain 1/(1-D) in
its non-isolated version did not have a soft start, and just the
opposite had a high in-rush input current so that additional
circuit needed to be employed to reduce in-rush currents.
In the isolated case, separate circuitry is needed to charge
the capacitor on the output to the input voltage so that the
converter could be started.
b) buck-boost (flyback) converter has a step-down/step-
up dc voltage gain so that a soft start is provided without any
additional circuitry for both non-isolated and isolated ver-
sions. On the other hand, as shown earlier, the buck-boost
converter causes very high voltage stresses on its two switch-
ing devices several times that of the output DC voltage.
The dc converter of Fig. 3a, however, combines the best
features of both boost and flyback converters and simultane-
ously eliminates their bad properties such that:
a) voltage stresses of all switches are equal to output dc
voltage under all operating conditions
b) soft-start is provided with voltage dc gain having char-
acteristic of step-down/step-up dc voltage gain in the low
duty ration region.
It is easy to verify that the above properties are also
present in the dc-dc converter with the negative dc input
voltage, so that the above advantages will be also present if
the bridgeless ac-dc converters of Fig. 1a and Fig. 1b. These
converters also allow operation directly of the ac line and
eliminate the bridge rectifier, unlike conventional boost and
flyback converters.
pfc conversion function
The equality of the dc conversion gains as a function of
duty ratio D of the controlling switch S proven above is one
important pre-requisite for a converter to operate as a Single-
Stage ac-dc (Bridgeless) converter with PFC function.
Another factor is that both DC conversion gains are
having a step-up dc gain characteristic which is another
pre-requisite needed for the converter topology to qualify
as Single-Stage ac-dc (Bridgeless) converter topology. This
therefore establishes that the converter of Fig. 1b is able to
operate as a single-stage (bridgeless) ac-dc PFC converter.
V/V
g
4
3
2
1
0.5 0.75
Step Up
D
(1 D)D
R
D
R
= 0.5
Step Up Step Down
D
1
1 D
Fig. 13. Characteristic waveforms for converters in Fig. 3a for variable off-time and for three effective operating duty ratios a) D=0.5, b) D= 0.66 c) D= 0.8
Fig. 14. Start-up operation. Theoretical dc conversion gain characteristic shown
exhibits the step-down/step-up voltage gain characteristic at low duty ratios
and transforms itself into a step-up only dc voltage gain characteristic at duty
ratio D
R
.
011PETCuk.indd 36 11/4/10 10:47:56 AM
www.powerelectronics.com November 2010 | Power Electronics Technology 37
BRIDGELESS PFCconverter
I XYS I XYS I XYS P OWER P OWER P OWER
Efciency Through Technology
A CLASS OF
THEIR OWN
High Voltage BiMOSFETS
TM
Excellent for high voltage
and high current applications
Features
Free intrinsic body diode
High blocking voltage
High current handling
capability
High power density
Low conducton losses
Applicatons
Capacitor discharge circuits
High voltage power supplies
High voltage test equipment
High voltage circuit breakers
AC switches
Pulser circuits
Laser & X-Ray generaton
systems
EUROPE
IXYS GmbH
[email protected]
USA
IXYS Power
[email protected]
ASIA
IXYS Taiwan
[email protected]
P artNumber P artNumber P artNumber V ds V ds V ds I C110 I C110 I C110 VC E(sa t ) VC E(sa t ) V CE(sat) t typ t typ t typ R thJC R thJC R thJC Pa ckag e Pa ckag e P ackage
In a departure from previous attempts at bridgeless PFC
conversion, all three switches, inductor L, resonant inductor
Lr, and resonant capacitor Cr are 100% utilized as they take
part in PFC operation for both positive as well as negative
part of input line ac voltage.
The Power Factor Correction is based on controlling the
average input current of the converters in Fig. 1b to become
proportional and in phase to the input ac line voltage by
use of the Bridgeless PFC IC controller. Thus, the duty ratio
modulation is used to control average input current of the
ac-dc switching converter of Fig. 1b, since it was demon-
strated that such a duty ratio control is effective in control-
ling the converter for either positive or negative parts of the
ac line voltage. The PFC control operates in two modes :
1.Duty ratio modulation with constant switching fre-
quency.
2. Constant ON-time and variable OFF time and therefore,
variable switching frequency.
LOOKING AHEAD
The fourth in a series of impossible converter solutions,
The Bi-directional Isolated Step-up Converter, will be
introduced in the January 2011 issue of Power Electronics
Technology. This converter, shown in Fig. 15, comprises-
three MOSFET switches and two magnetic components. It
has a bi-directional power flow capability to convert input
low battery voltage VL (14V-32V) to high output battery
voltage VH (270V) and vice versa.
Editorial Note: For questions regarding this article and for
contact information to the author the readers are directed
to TESLAcos Web site www.teslaco.com.
Footnote: Isolated Bridgeless PFC Converter and
Single-Stage Isolated PFC Converter are trademarks of
TESLAco.
REFERENCES
1. Slobodan Cuk, Modelling, Analysis and Design of Switching Converters,
PhD thesis, November 1976, California Institute of Technology, Pasadena,
California, USA.
2. Slobodan Cuk, R.D. Middlebrook, Advances in Switched-Mode Power
Conversion, Vol. 1, II, and III, TESLAco 1981 and 1983.
3. Slobodan Cuk, State-Space Averaging: Past, Present and Future. Invited
paper, APEC Power Electronics Conference, Fort Worth, Texas, March 6,
2011.
C
r1 C
r2
N
P
N
S
L
S
3
v
L
S
2
V
H
S
1
S
2
3
Lr
Fig. 15. The fourth impossible converter solution, an Isolated Step-up dc-dc
Converter with Bi-directional current flow capability uses only three MOSFET
switches, and two magnetic parts, in addition to a small resonant inductor and
small resonant capacitor.
011PETCuk.indd 37 11/4/10 10:48:05 AM