Prepared by:

F-2 ISOLATED Engr. Nestor DJ. Roda TWS Page 1 of 3

Civil Engineer

1) Design Criteria:
Unit weight of Concrete, Wc = 23,537 N/m3
Steel tensile unit stress, Fs = 124.13 MPa
Compressive strength of concrete, Fc' = 20.69 MPa
Compressive stress of concrete, Fc = 9.31 MPa
Modulus of elaticity ratio, n = 9
Design constant, k = 0.40295
Design constant, j = 0.86568
Design constant, R = 1.62 MPa
Soil pressure (assumed), B = 150.0 KPa
Seismic Factor (Standard Occupancy Structure) = 1.50
Column load, P = 91661.00 N
column width,w = 0.20 m
Assumed column load as weight of the footing = 10%

2) Weight of footing:
Weight of footing = 10% of column load
Wft = 9166.10 N

3) Total load:

Total load = P + W ft
TL = 151240.65 N

4) Required footing area:

TL
A =
B
151.24 KN
A =
150.0 KPa

A = 1.01 sqm

5) Square footing dimension:

L = width of each side

L = A
L = 1.004 m
Say L = 1.30 m OK !

Try 1.30 m X 1.30 m

6) Solve for q (Net soil pressure)

P
q =
(L)(L)

91.66 KN
q =
1.69 sqm

q = 54.24 KN/m2

RCC DESIGNCOMPU 20/12/2024 6:02 am

 Prepared by:
F-2 ISOLATED Engr. Nestor DJ. Roda TWS Page 2 of 3
Civil Engineer

7) Moment Computation:
(L - w)2
M = q X L X
2
M = 42.66 KN . m

8) Compute for d:
M
d =
Rb
d = 0.142 m
Say d = 0.250 m OK !

9) Check for shearing stress :

V allowable = 0.09 Fc'

V allowable = 0.409 MPa

Vd
V actual =
bd

where: Vd - is the shear at a distance "d"

from the support

L-w
V actual = q X L X - d
2
V actual = 0.021 MPa

Since V allowable > V actual , then it is OK !

10) Check for punching shear :

Vp allowable = 0.17 Fc'

Vp allowable = 0.773 MPa

Vp
Vp actual =
Ap

where: Vp = q X L2 - (w + d)2
Vp = 80.68 KN

Ap = 4(w+d)(d)
Ap = 0.45 sqm

Vp actual = 0.179 MPa

Since Vp allowable > Vp actual , then it is OK !

RCC DESIGNCOMPU 20/12/2024 6:02 am

 Prepared by:
F-2 ISOLATED Engr. Nestor DJ. Roda TWS Page 3 of 3
Civil Engineer

11) Check for the actual weight of the footing:

2
Wact = h x L x Wc
Wact = 12927.70 N
Since W ft < Wact then it is NOT OK !

12) Steel Reinfocements:

M
AS =
Fs j d
AS = 0.001588 m2

Using 20 mm daimeter bar: A16 = 0.000314 m2

0.001588 m2
# of bars =
0.000314 m2
# of bars = 5.05 pcs

Say 13 pcs 16mm

20 mm
dai
Ø deformed
Steel Bar bar OK !

13) Check for bond stress:

10.14 Fc'
U allowable =
D

where: D - Daimeter of the bar used

U allowable = 2.306 MPa

Vt
U actual =
ojd

where: o - Sum of the perimeter of the bar used

U actual = 0.219 MPa

Since U allowable > U actual , then it is OK !

14) Details:

250 mm
325 mm
75 mm c/cover
13 - 20 mmØ
deformed bar
1.30 m
both ways

RCC DESIGNCOMPU 20/12/2024 6:02 am