Scribd
Upload
17 views7 pages

Priyadarshini College of Engineering, Nagpur

The document is a question bank for the Network Theory & Analysis course at Priyadarshini College of Engineering, covering various topics such as mesh analysis, source transformation, nodal analysis, Thevenin’s and Norton’s theorems, and Laplace transforms. It includes a series of questions requiring explanations, derivations, and calculations related to electrical networks. The questions are designed for third-semester B.Tech students in the Department of Electronics & Communication Engineering for the academic year 2024-25.

Uploaded by

wigada8921
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
17 views7 pages

Priyadarshini College of Engineering, Nagpur

The document is a question bank for the Network Theory & Analysis course at Priyadarshini College of Engineering, covering various topics such as mesh analysis, source transformation, nodal analysis, Thevenin’s and Norton’s theorems, and Laplace transforms. It includes a series of questions requiring explanations, derivations, and calculations related to electrical networks. The questions are designed for third-semester B.Tech students in the Department of Electronics & Communication Engineering for the academic year 2024-25.

Uploaded by

wigada8921
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

PRIYADARSHINI COLLEGE OF ENGINEERING, NAGPUR

Department of Electronics & Communication Engg.


Third Semester B.Tech. - Network Theory & Analysis
Academic Calendar ( Odd:2024-25 )
Question Bank

1]Write down the steps for Mesh Analysis.


2] State and explain source transformation
3] Determine the current in the 5 Ω resistor in the network given below.

4] Write and solve mesh equations for the given network

5] Convert the combination shown below to a single source in parallel with a single element.

6] Reduce the network shown below to only one source without combining any of the resistance
branches.
R1

3A
R2 R3

10 V R4 3A R5
7] For the network shown below, write down mesh equations in matrix form.
L2

R1
C1
C2

L1 V
R2

8] Write and solve mesh equations for the given network

9] Define duality and explain conditions for duality.


10] Determine the node voltages Va & Vb and find out the power dissipated in the
inductor for the ckt. Shown below.

11] Determine current through inductor in figure using nodal analysis.

12] Draw the dual of the network shown below.


13] Use supernode analysis to find voltages V1 & V2 of the given network.

14] Find the current through 2 Ω resistor by using nodal analysis.

15] Write down the steps for implementing Thevenin’s Theorem


16] State and prove Maximum power transfer theorem.
17] Find ‘RL & XL’ for the maximum power transfer of the network shown below. Also find the
value of maximum power.

18] In the network shown below, determine voltage across 3 Ω resistor and then verify
Reciprocity theorem.

19] Determine V1 such that the current through the impedance (3+j4) is zero. Use
Thevenin’s Theorem.
20] Detetrmine open ckt voltage and short ckt current at terminals a & b and hence
draw Thevenin’s & Norton’s equivalent ckt of the network shown below.

21] Explain steps for applying Norton’s Theorem


22] In the network shown below, switch ‘K’ is changed from ‘a’ to ‘b’ at t=0. A steady state have
been established at position ‘a’. Show that at t=0+, i1=i2= -V/(R1+R2+R3) & i3=0

23] In the network shown below, a steady state is reached when the switch ‘K’ is open. At t=0, the
switch is closed. For element values given, determine the values of Va(0-) & Vb(0+).

24] The network shown in figure below is in steady state with switch ‘K’ closed. At t=0, the switch
is opened. Determine Vk, dVk/dt at t=0+.

25] Write down the steps for finding Initial Conditions


26] In the series RC circuit of fig. the capacitor has initial charge of 2.5mC. At t=0, the switch is closed
and a constant voltage source V=100 volt is applied. Use Laplace Transform to find current i(t).

27] Find the current i2(t) using Laplace Transform method, if the switch is closed at t = 0 in shown network.

28] The network shown below has acquired steady state with switch closed for t < 0. At t = 0, the
switch is opened. Obtain i(t) for t > 0

29] An exponential voltage v(t) =10e-t is suddenly applied at t=0 to a series RLC ckt
shown below. Obtain the particular solution for current i(t) in a loop.

30] Find I(t) flowing through 4H inductor shown in fig, if switch is in position ‘A’ till
steady state is reached & is shifted to ‘B’ at t=0.
31] Express the function shown below as a combination of step function. Obtain its Laplace
Transform.

32] Show that transfer function of the following function shown is


F(s) = coth(s/2)/(s2 + 1).

33] Derive the Reciprocity condition for ABCD parameter.


34] Derive the Reciprocity condition for Hybrid parameter.
35] Derive the reciprocity condition for h-parameter
36] Derive the Reciprocity condition for Y- parameter.
37] Derive the Reciprocity and Symmetry conditions for ABCD parameter
38] Find the Z – parameter of the network shown below.
39] Determine Y – parameter of the network shown below

40] Explain two port parameter.

You might also like