Scribd
Upload
5 views

ad-net-networking

The Ad-NeT networking system connects MxPro 5 series control panels and peripherals using standard fire-resistant cable, supporting networks from two to 200 panels. It features a true peer-to-peer system for data sharing, easy network expansion, and diagnostic capabilities. The system includes options for standard and fault-tolerant network cards, with specific limitations on cable length and number of nodes.

Uploaded by

karmoz139
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
5 views

ad-net-networking

The Ad-NeT networking system connects MxPro 5 series control panels and peripherals using standard fire-resistant cable, supporting networks from two to 200 panels. It features a true peer-to-peer system for data sharing, easy network expansion, and diagnostic capabilities. The system includes options for standard and fault-tolerant network cards, with specific limitations on cable length and number of nodes.

Uploaded by

karmoz139
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Ad-NeT Networking

The Ad-NeT network system allows all


MxPro 5 series control panels, remote
terminals and network peripherals to be
connected together using standard fire
resistant two-core cable. It provides both
the benefits of distributed intelligence and
reduced installation costs whilst catering
for the smallest two-panel network through
to the largest 200 panel wide area
networked system.

The network operates as a true peer-to Key Features


peer system allowing information from any
Large Ad-NeT+ 200 Panel Network
input or output device to be passed over
the network and displayed on any MxPro
Up to 1.5Km between Control Panels
5 control panel or remote terminal as Windows based PC setup
required. Network Systems share up to 1000 zones
Network Analysis from Contol Panel
Simply adding and connecting a network
card allows any MxPro 5 control panel or
remote terminal to be networked. All other Specification
nodes on the Ad-NeT system will be
Network Connections IN: A/B SCN(Screen)
instantly aware of a panel as soon as it is OUT: A/B SCN (Screen)
given a valid network node address,
allowing additional panels to be added at On-board Indication 2 Red LED’s.
any time. All panels incorporate a network LED 1 illuminates when data is transmitted
LED 2 illuminates when data is received
analyser providing valuable diagnostic and
status information and also have the Supply Current Mxp-503 Standard Network card: 20mA
facility to prevent the transmission of fires Mxp-509 Fault tolerant Network Card: 61mA
or faults during commissioning. (All power taken directly form the panel
motherboard)
For more complex systems, the Windows Temperature range -5°C to 40C
based PC-NeT Mx configuration software and Humidity 95% non-condensing (maximum)
allows sector based programming for
Dimensions 85mm x 65mm x 20mm
Mute, Silence, Resound and Reset control (H x W x D) (Mounting pillars are provided on the panel
keys as well as investigation delays, group chassis to mount this card)
disablement and test instructions. All
Recommended Cable 2 Core twisted-pair plus screen
panels within the same sector will share
common controls and each panel or
remote terminal can also be programmed
to show specific network information on a Order Codes and Options
zonal basis. For cause and effect, any Mxp-503: Standard Network Card
input device can be programmed to Mxp-509: Fault Tolerant Network Card
operate any output device on any panel. Mxp-503F: Standard Network Card fitted to an MxPro 5
control panel
Mxp-509F: Fault Tolerant Network Card fitted to an
MxPro 5 control panel

v1.0
Limitations
Standard Network
The maximum total cable length is 1.5km. The maximum number of network nodes is 32 (50 with signal buffer)

Fault Tolerant Network


The maximum cable length is 1.5km between each node and the maximum total loop length is 20km. Each network card
has in-built diagnostics and is fully monitored for both short and open circuit faults between nodes. The network is capable
of withstanding a single fault between nodes without loss of communications to any single panel. The maximum number of
network nodes is 200.

You might also like