B.

TECH/AEIE/5TH SEM/AEIE 3103/2021

B.TECH/AEIE/5TH SEM/AEIE 3103/2021

MICROPROCESSORS & MICROCONTROLLERS

(AEIE 3103)

Time Allotted : 3 hrs Full Marks : 70

Figures out of the right margin indicate full marks.
Candidates are required to answer Group A and
any 5 (five) from Group B to E, taking at least one from each group.
Candidates are required to give answer in their own words as far as practicable.

Group – A
(Multiple Choice Type Questions)

1. Choose the correct alternative for the following: 10 × 1 = 10

(i) In 8085 microprocessor number of 16 bit register is-
(a) 2 (b) 3 (c) 6 (d) 8
(ii) In memory read operation what is the status of 𝐼𝑂/𝑀 ,𝑅𝐷, 𝑊𝑅 control signals.
(a) 𝐼𝑂 / 𝑀 = 1, 𝑅𝐷 = 1, 𝑊𝑅 = 0 (b) 𝐼𝑂 / 𝑀 = 1, 𝑅𝐷 = 0, 𝑊𝑅 = 1
(c) 𝐼𝑂 / 𝑀 = 0, 𝑅𝐷 = 1, 𝑊𝑅 = 0 (d) 𝐼𝑂 / 𝑀 = 0, 𝑅𝐷 = 0, 𝑊𝑅 = 1
(iii) What is the content of D and E register after the execution of DCR D instruction?
Let the initial values are D=23H, E=32H.
(a) D=23H, E=31H (b) D=22H, E=32H
(c) D=22H, E=31H (d) None of these
(iv) In IN F0H instruction content of A0- A7 and A8- A15 address lines are-
(a) A0- A7= F0H and A8- A15 =00H
(b) A0- A7= 00H and A8- A15 =F0H
(c) A0- A7= F0H and A8- A15 =F0H
(d) A0- A7= F0H and A8- A15 =High impedance state
(v) In JNZ 4000H instruction program execution will be shifted to 4000H memory
location when-
(a) Z=0 (b) Z=1 (c) CY=0 (d) CY=1
(vi) If the operating frequency of 8085 is 2 MHz, then the time required to execute
an instruction of 13T states is-
(a) 5 µsec (b) 6.5 µsec (c) 13 µsec (d) 26 µsec
(vii) After reset operation content of SP register in 8051 µC is-
(a) 00H (b) 07H (c) 0000H (d) FFH

AEIE 3103 1
B.TECH/AEIE/5TH SEM/AEIE 3103/2021
(viii) What is the value of control word register where Port A and Port B is configured
as Output in Mode 0 and Port C is configured as Input?
(a) 80H (b) 91H (c) A2H (d) None of these
(ix) In 8051 µC if RS1=0 and RS0=1 then the selected register bank is-
(a) Bank 0 (b) Bank 1 (c) Bank 2 (d) Bank 3
(x) 8051 µC will read instruction from its internal program memory if-
(a) RST pin is at logic 0 (b) RST pin is at logic 1
(c) 𝐸𝐴 pin is at logic 0 (d) 𝐸𝐴 pin is at logic 1

Group- B

2. (a) Draw and discuss the flag register of 8085 microprocessor.

[(CO1) (Remember/LOCQ)]
(b) With one suitable circuit diagram explain the process of de-multiplexing of
lower order address bus and data bus in 8085 microprocessor.
[(CO1) (Understand/LOCQ)]
(c) Read the program and answer the following questions:
MVI A, 17H
Loop: ORA A
RAL
JNC Loop
STA 5000H
HLT
i) What is the function of ORA A instruction?
ii) What is the function of JNC Loop instruction?
iii) How many times the Loop will be executed?
iv) What is the content of memory location 5000H?
[(CO2)( Analyze/IOCQ)]
(1 + 3) + (1 + 2) + (1 + 1 + 2 + 1) = 12

3. (a) Discuss the programmable and non-programmable registers of 8085

microprocessor. [(CO1) (Remember/LOCQ)]
(b) Calculate the amount of delay generated in the following subroutine.
MVI A, F0H
Loop: DCR A
JNZ Loop
RET. [(CO5) (Analyse/IOCQ)]
(c) Write an ALP for 8085 microprocessor to store the last two digits of your
autonomy roll and registration numbers in memory location 4000H and 4001H.
Increment the content of location 4000H by 2. Perform XOR operation between
the contents of location 4000H and 4001H and store the result in memory
location 4002H. [(CO2)(Solve/IOCQ)]
5 + 2 + 5 = 12

AEIE 3103 2
B.TECH/AEIE/5TH SEM/AEIE 3103/2021
Group - C

4. (a) What is the difference between absolute and partial address decoding?
[(CO3) (Remember/LOCQ)]
(b) Design a circuit to interface one 8KB ROM and one 8KB RAM memory chips to
8085 microprocessor. The first address in the ROM memory chip is 0000H and
the last address in RAM memory chip is FFFFH. [(CO3) (Design/HOCQ)]
2 + 10 = 12

5. (a) What is difference between vectored and non-vectored interrupts of 8085

microprocessor. Give an example of maskable and non-maskable interrupts of
8085 microprocessor. [(CO4) (Understand/LOCQ)]
(b) Design a circuit to interface one 7 segment display to 8085 microprocessor
using Latch as interfacing device. Consider the last two digits of your autonomy
roll number as the IO port address. [(CO3) (Design/HOCQ)]
(c) Write a program for above circuit to display the last digit of your registration
number on the 7 segment display. [(CO3) (Solve/IOCQ)]
(2 + 2) + 4 + 4 = 12

Group - D

6. (a) Draw and discuss the control word register (CWR) format of 8255 PPI in BSR
mode. [(CO6) (Remember/LOCQ)]
(b) Design a circuit to interface TWO 7 segment displays to 8085 microprocessor
using 8255 PPI. Let the Port A address of 8255 PPI is X0H (Where, X is the last
digit of your autonomy roll number). [(CO6) (Design/HOCQ)]
(c) Write a program for the above circuit to display the last two digits of your
autonomy roll number on the 7 segment displays.Also mention the CW value
and 7 segment codes. [(CO6)(Solve/IOCQ)]
(1 + 2) + 4 + (4 + 1) = 12

7. (a) Draw and discuss the internal architecture of 8251 USART.

[(CO6) (Remember/LOCQ)]
(b) Design a circuit to interface one A/D converter to 8085 microprocessor using
8255 PPI.Let the Port A address of 8255 PPI is X0H (Where, X is the last digit of
your autonomy roll number). [(CO6) (Design/HOCQ)]
(c) Write a program to blink one LED connected at PC0 line of 8255 PPI.
[(CO6)(Solve/IOCQ)]
(2 + 4) + 4 + 2 = 12

Group - E

8. (a) What are the differences between microprocessor and microcontroller?

[(CO1) (Remember/LOCQ)]
AEIE 3103 3
B.TECH/AEIE/5TH SEM/AEIE 3103/2021
(b) With suitable example discuss the function of RS1 and RS0 bits in 8051
microcontroller? [(CO1) (Understand/LOCQ)]
(c) Write an ALP for 8051 microcontroller to store 10 random numbers in RAM
memory location starting from 20H. Count the number of even and odd numbers
presents in the block and store the result in RAM memory. [(CO2)(Solve/IOCQ)]
3 + 3 + 6 = 12

9. (a) What is the function of TxD pin in 8051 microcontroller?

[(CO1) (Remember/LOCQ)]
(b) Design a circuit to interface one 7 segment display unit and one switch to 8051
microcontroller. [(CO6) (Design/HOCQ)]
(c) Write a program for the above circuit to display the last digit of your autonomy
roll number on the 7 segment displays if the switch is open and display the last
digit of your registration number if the switch is closed. [(CO6)(Solve/IOCQ)]
2 + 4 + 6 = 12

Cognition Level LOCQ IOCQ HOCQ

Percentage distribution 36.45% 36.45% 27.10%
Course Outcome (CO):
After the completion of the course students will be able to:
1. Learn the architecture of 8 bit microprocessor (8085), 8051 and PIC (PIC16F877)
microcontrollers
2. Develop the skill in program writing for 8085 microprocessor, 8051 and PIC
microcontroller
3. Realize the interfacing of memory, input/output devices with 8085 microprocessor
4. Understand the interrupts of 8085 microprocessor, 8051 and PIC microcontroller
5. Learn the use of timer/counter and serial data communication process in 8085
microprocessor and 8051 microcontroller
6. Apply the knowledge to interface different type of I/O devices with 8085
microprocessor, 8051 and PIC microcontroller

*LOCQ: Lower Order Cognitive Question; IOCQ: Intermediate Order Cognitive Question;
HOCQ: Higher Order Cognitive Question

Department &
Submission Link
Section
AEIE https://classroom.google.com/c/NDA2MDE5NDU4ODQ2/a/NDYzODgwODY3NzM5/details

AEIE 3103 4