CS610- COMPUTE

NETWORK
(SOLVED MCQs)
FROM MIDTERM PAPERS
LECTURE (1-22)
ajtechinstitute24@gmail. For More Visit: vujunaid.com JUNAID MALIK (0304-
com 1659294)
 ÂL-JÛÑÂÎD TÊCH
JOIN OUR GROUP FOR MORE UPDATE
Click Button
CS619 & CS519 ÂL-JÛÑÂÎD
TÊCH

1. In Cyclic Redundancy Checking, CRC is __________.

a. Divisor
b. Quotient
c. Remainder page 20
d. Dividend
2. The satellite or radio topology in which all computers are
connected to each other via satellite or radio wave is a kind of
a. Broadcast network page 5
b. Point-to-Point network
3. Which of the following two operations are performed by Ethernet CD?
I. It monitors outgoing signals.
II. Grabbled signal is interpreted as a collision.
III. Signals are sent back to the sender.

a. I and III
b. II and IV
c. II and III
d. I and II page 28
4. The process of forwarding a packet is called ____________.
a. Routing page 58
b. Processing
c. Hierarchical Addressing
d. Source Addressing
4. Which statement is correct about Network Interface Card (NIC)?
I. NIC contains sufficient hardware to process data independent of
system CPU
II. NIC looks like any other I/O device to system CPU III.
NIC also receives interrupt on incoming data.
a. I and II
b. II and III
c. I and III
d. All of the given options page 40

0304-1659294 1

-
 ÂL-JÛÑÂÎD TÊCH
5. While transmitting data from source A to destination B, 4 bits
are changed during the transmission then the error is a _________.
a. Burst error page 22
b. Single error
c. Double error
d. Logic error
6. The switch that has no attached computers is called __________.
a. Packet Switch
b. Exterior Switch
c. Interior Switch page 59
d. External Switch
7. ________ is the most popular wiring scheme because of lowest cost.
a. 5 Base T
b. 10 Base T page 43
c. 100 base T
d. 1000 base T
8. In _________ technique, all members of the network can send data
only on the specific time slot?
a. CDMA
b. FDMA
c. CSMA page 43
d. TDMA
9. If a sender with a 100 Megabit NIC and receiver with 10 Megabit NIC wants to
communicate with each other at which speed they can communicate?
a. 100 Megabit page 40
b. 110 Megabit
c. 1000 Megabit
d. 10 Megabit
9. Missing ______ in a frame format indicates receiving computer missed
beginning of the message.
a. eot
b. soh page 16
c. sot
d. eoh
10. 1The _______ of errors is easier than the ________ of errors.
a. correction; detection
b. detection; correction cs601 handouts
c. correction; creation
d. detection; manipulation

0304-1659294 2

-
 ÂL-JÛÑÂÎD TÊCH
10. 1The _______ of errors is difficult than the ________ of errors.
a. correction; detection google
b. detection; correction
c. correction; creation
d. detection; manipulation
11. 1Source Independence phenomenon allows fast and efficient
____________.
a. Source Addressing
b. Routing
c. Packet Switching page 58
d. Store and forward
12. 1In distributed route computation process each packet switch computes
its routing table locally and sends messages to the __________.
a. Router
b. Graph
c. Neighbors page 63
d. WAN
13. The ___ layer of the OSI model takes the data from the physical layer and
perform error checking.
a. Transport
b. Data link google
c. Application
d. Presentation
14. 1 CBR stands for _________.
a. Constant Byte Rate
b. Constant Bit Rate
c. Connection break Recovery
d. Constant Borrow Rate
15. 1A network that uses _______ usually consist of a single long cable to which
computer attach.
a. Star Topology
b. Ring Topology
c. Bus Topology page 26
d. Bus and Ring Topology
16. If simultaneous transmission occurs, the frames interfere with each other and
this phenomenon is called _______.
a. packet loss
b. collision page 28
c. delayed transmission
d. coordination

0304-1659294 3

-
 ÂL-JÛÑÂÎD TÊCH
16. In __________ all computers are attached to a central
hub a. Ring topology
b. Star topology page 31
c. Hub topology
d. Bus topology
17. For adding a new computer in a point to point network ______new
connection
will be required
a. N
b. N-1 page 23
c. N-2
d. 2n
18. 1The fastest Ethernet hardware operates at a rate of _____
a. 1000 bps
b. 100 Mbps page 27
c. 10 Mbps
d. 1000 Mbps
18. Which of the following the benefit to point to point
communication? a. Quick to configure
b. Security implementation page 23
c. Cost
d. Less availability
19. 1 ATM offers _____speed and ________delay
a. High, High
b. High, low page 72
c. Low, low
d. Low, high
20. 1Thick Ethernet is known as ___________
a. 10 Base 2
b. 10 Base 5 google
c. 10 Base T
d. 10 Base 10
21. Both interior and exterior switches _______packet and they also need routing
tables.
a. Create
b. Delay
c. Forward page 59
d. Start

0304-1659294 4

-
 ÂL-JÛÑÂÎD TÊCH
22. ______is the rate at which data can be sent through the network
a. Throughput page 79
b. Propagation delay
c. Access delay
d. Switching delay
23. In a ping command, small –sized information packets of _____are sent.
a. TCP
b. UDP
c. ICMP page 11
d. IGMP
24. Many WANs use ______addressing of efficiency
a. Sequence
b. Forward
c. Hierarchical page 56
d. Sequential
25. Which of the following is not a function of ping commends?
a. Local computer network issue
b. Congestion in the network

c. Relay nodes page 11

d. Remote host availability
26. Packet switched can be linked together to form a ________
a. LAN
b. WAN page 56
c. Bridge
d. None of the given option
27. Fixed network is a type of network which is classified with repect to the
______factor
a. Size
b. Connectivity
c. Medium
d. Mobility page 6
28. Parity bit can detect _________________error(s)
a. 4
b. 3
c. 2 page 19 (even or odd)
d. 1

0304-1659294 5

-
 ÂL-JÛÑÂÎD TÊCH
29. When we will try to connect to the internet which of the following protocol will
be used?
a. Telnet
b. TCP/IP page 84
c. ICMP
d. IPx
30. How many computers are mandatory to form a network?
a. 1
b. 2 google
c. 4
d. 8
31. ________ is standard wireless LAN that uses radio signals at 2.4GHz.
a. IEEE 803.16
b. IEEE 802.15
c. IEEE 802.3
d. IEEE 802.11 page 29
32. LAN interface hardware obeys ______ access rule.
a. CSMA/CD page 34
b. Round robin
c. First come first served
d. High priority
33. The most important task a bridge performs is _________.
a. Packet switching
b. Line controlling
c. Noise controlling
d. Frame filtering page 50
34. ATM uses small, fixed-sized packets called cells and each cell has _____
octets.
a. 47
b. 52
c. 53 page 66
d. 55
36. ___________ can't be guaranteed with variable length packets as easily as it can
with fixed length cells.
a. Errors
b. Noise
c. Quality of Service page 72
d. None of the given

0304-1659294 6

-
 ÂL-JÛÑÂÎD TÊCH
37. Which multiplexing technique transmits digital signals?
a. WDM
b. FDM
c. TDM page 15
d. GSM
38. Connections in Asynchronous transfer mode are called ________.
a. Virtual channels page 67
b. Virtual Path Identifier
c. Cells
d. Cell tax
39. A _______ is a device that combines multiple signals and forwards into a single
line.
a. Modem
b. Multiplexer page 41
c. Repeater
d. Layer 3 Switch
40. ___________ is inflexible.
a. Routing
b. Searching
c. Processing
d. Static routing page 62
41. If a hub is used to connect many computers in a LAN, then only _______
computers can communicate at a given time.
a. Three
b. Two page 54
c. Four
d. One
42. _________ is the term used for variance in transmission delays.
a. Friction
b. Segment
c. Checksum
d. Jitter page 66
43. ________ is also called self healing network.
a. ATM
b. FDDI
c. Token Ring page 46
d. Frame relay

0304-1659294 7

-
 ÂL-JÛÑÂÎD TÊCH
44. _______ and _______ are the two frame types.
a. Internal and external
b. Single and dual
c. Implicit and explicit
d. Multicast and broadcast page 35
45. Bluetooth uses shared medium and _______ instead of coaxial cable.
a. Radio waves page 29
b. Infrared waves
c. Micro waves
d. Low frequency waves
46. Which of the following is not a guided medium?
a. Twisted-pair cable
b. Fiber-optic cable
c. Atmosphere google
d. Coaxial cable
47. As a result of ARPA research, the first network was established which
was named as ________.
a. INTERNETWORKING
b. ARPNET
c. ARPANET page 9
d. PACKET NETWORK
48. Asynchronous transfer mode (ATM) can dynamically establish a __________.
a. Switched virtual circuit page 70
b. Virtual connection identifier
c. Virtual path indicator
d. None of the given options
49. A typical port on an ATM switch operates at ________ or _______ higher.
a. OC-2 speed (155Gbps)
b. OC-2 speed (1000Mbps)
c. OC-3 speed (155Mbps) page 72
d. OC-3 speed (100Gbps)
50. 10Base-T Ethernet is often called a __________.
a. ring shaped star
b. ring shaped bus
c. star shaped bus page 46
d. star shaped ring

0304-1659294 8

-
 ÂL-JÛÑÂÎD TÊCH
51. ___________ allows automatic updates.
a. Dynamic routing page 62
b. Static routing
c. Routing
d. Default routing
52. Handling variable length packets leads to memory __________.
a. Fragmentation page 72
b. Management
c. Location
d. Allocation
53. In order to forward a copy of frame, the bridge uses ________ address.
a. Network
b. Destination page 51
c. IP
d. Source
54. We may use _______ to extend local area network.
a. Bridge, Router
b. Bridge, Hub, Router
c. Bridge, Hub, Repeater page 149
d. Bridge, Hub, Repeater, Router
53. All of the given options are the types of delay except __________.
a. Propagation
b. Access
c. Throughput page 79
d. Queuing
54. While computing shortest path in a graph, next hop information is inserted into
_________.
a. Routing table page 62
b. Trailer
c. Header
d. Register
55. LAN interface uses _________ to copy frame data directly from main memory
a. DMA page 34
b. FDDI
c. Hard disk
d. Flash

0304-1659294 9

-
 ÂL-JÛÑÂÎD TÊCH
56. The Gigabit Ethernet hardware operates at a rate of ___________.
a. 10 Mbps
b. 100 Mbps
c. 1000 Mbps reference book page 263
d. 1000 Gbps
57. In the early resource sharing era, which resources were shared among users?
a. Computation page 9
b. Floppy Drives
c. Hard Disk
d. Printers
58. If two buildings are located far from each other then bridge, and ________ can
be used to connect two LAN.
a. Optical fiber page 51
b. Ethernet modem
c. Switch
d. NIC
59. Which type of network consists of wireless connection of laptops in a university
classroom?
a. WAN
b. MAN
c. Fog
d. LAN google
60. A typical bridge has _______________.
a. One NIC, a CPU a memory and a ROM.
b. Two NICs, a CPU a memory and a ROM. page 50
c. RAM, ROM and CPU.
d. A cache memory, ROM and CPU.
61. __________ is used for compressed audio and video, where the data rate
depends on the level of compression that can be achieved.
a. Constant Bit Rate
b. Stable Bit Rate
c. Variable Bit Rate page 71
d. Available Bit Rate
62. There are ________ types of data stuffing.
a. 1
b. 2 page 17
c. 0
d. 5

0304-1659294 10

-
 ÂL-JÛÑÂÎD TÊCH
63. Dijkstra's algorithm can accommodate weights on _______ in graph.
a. Nodes page62
b. Edges
c. Path
d. Connections
64. ________ masks your IP address.
a. Firewall
b. Antivirus
c. VPN
d. Incognito mode
65. Static routing computes routing table information at __________ time.
a. Load
b. Boot page 62
c. Execute
d. One
66. ___________ was the first automated tool required to see whether the given
computer is online or not.
a. Probing program
b. PING program page 11
c. status program
d. None of the above
67. In which type of error detection, the arithmetic sum is calculated before
and after the transmission of data at both communication ends?
a. CRC
b. Party
c. Checksum page 19
d. Hash Function
68. Computer sends a connection request to the ________ to which it is attached
while establishing a switched virtual circuit
a. Bridge
b. Switch page 70
c. VPI
d. Virtual circuit
69. The bridges communicate with each other on the network and use ________
algorithm to decide which bridge will not forward frames if a cycle occurs.
a. Djikstra
b. Shortest path first
c. Vector distance
d. Distributed Spanning Tree page 53

0304-1659294 11

-
 ÂL-JÛÑÂÎD TÊCH
70. Ethernet uses a ______ bit static addressing scheme in which each device is
assigned a unique address by the manufacturer.
a. 64
b. 48
c. 32
d. 16
71. Weights on graph edges reflect cost of ____________.
a. Nodes
b. Traversing edge page 63
c. Trending edge
d. Path
72. A ________ relies on the hardware manufacturer to assign a unique physical
address to each network interface.
a. Static addressing scheme page 34
b. Configurable addressing scheme
c. Dynamic addressing scheme
d. None of the given
73. In _______ topology, if the switch goes down all the computers will be
disconnected.
a. Star
b. Ring
c. Bus
d. Mesh
74. Which type of network consists of wired computers in a university classroom?
a. MAN
b. PAN
c. WAN
d. LAN
75. If you as a network administrator want to know the traffic flow of your data
while communicating with a remote computer which of the following will be
used to know about intermediate routers?
a. Ipconfig
b. Ping page 11
c. Traceroute
d. Arp
76. Hardware address is also called _____________.
a. Physical address
b. Logical address
c. IP address
d. Port address

0304-1659294 12

-
 ÂL-JÛÑÂÎD TÊCH
77. Thick Ethernet also requires _________ to avoid signal reflectance.
a. Transceivers
b. AUI cable
c. Drop cable
d. Terminators page 41
78. Which of the following network is using the TCP/IP model globally?
a. PAN
b. SAN
c. LAN
d. The Internet
79. VPNs connections are sometimes called ________.
a. Tunnels page 75
b. Open networking
c. Routing
d. Public network
80. To reduce _______ computers can be connected and distributed to a number of
hubs, then the hubs can be connected to a switch.
a. Costs page 54
b. Quality
c. Efficiency
d. Noise
81. If a __________ is used the communication between two computers will not
affect the other pair of computers and they can communicate at the same time
a. Hub
b. Switch page 54
c. Repeater
d. Amplifier
82. The length of hardware address is ______________.
a. One to ten bytes
b. One to five bytes
c. One to six bytes page 34
d. One to seven bytes
83. A network analyzer is also called _________.
a. Network manager
b. Network administrator
c. Network monitor page 37
d. Network

0304-1659294 13

-
 ÂL-JÛÑÂÎD TÊCH
84. No any error detection scheme is perfect because transmission errors can affect
_________.
a. Data
b. Additional Information
c. Additional information & data google
d. Transmission medium
85. The token ring network topology is a ring but wiring topology is a _________.
a. Star page 44
b. bus
c. tree
d. mesh
86. _______ addresses are used in an ethernet frame.
a. IP page 99
b. Port
c. Logical
d. МАС
87. AUI cable connects from NIC to ___________.
a. BNC Connector
b. RJ-45 Connector
c. Transceiver page 41
d. Terminator
88. Public networks are _______________.
a. More secure than LAN
b. Flexible page 74
c. Limited in boundary
d. Intranet
89. The maximum cable length of a LAN is fixed because _________________.
a. Additional hardware are not suitable for the LAN extension.
b. The electrical signal level gets weaker as it travels. Page 48
c. Additional software are not suitable for the LAN extension
d. The electrical signal level gets stronger as it travels.
90. In _______.network topology is separated from route computation.
a. Local area
b. Link-state routing page 64
c. Static routing
d. Dynamic routing

0304-1659294 14

-
 ÂL-JÛÑÂÎD TÊCH
91. Which layer of the OSI Model directly communicates and controls
the transmission medium:
a. Transmission
b. Physical
c. Application
d. Network
92. In ________ technique data is treated as a sequence of integers and their
arithmetic sum is computed and the carry bits are added to the final sum.
a. CRC
b. Bit stuffing
c. Checksum page 19
d. 2D Parity
93.A network with _______ jitter takes more time to deliver some packets than
others.
a. Zero
b. High page 80
c. Low
d. Moderate
94. A network uses _______ to arrange computers in a single closed loop.
a. Star Topology
b. Mesh Topology
c. Ring Topology page 25
d. Bus Topology
95. Which of the following tasks is not done by the second layer of the OSI
model?
a. Flow control
b. Framing
c. Channel coding google
d. Error control
96. ATM is a single technology designed to meet the goals of both ________
and __________.
a. LAN & PAN
b. LAN & WAN page 66
c. LAN & MAN
d. MAN & WAN
97. LAN and WAN are classified according to their _______.
a. Size page 4
b. Connectivity
c. Medium
d. Mobility

0304-1659294 15

-
 ÂL-JÛÑÂÎD TÊCH
98. The identifier that is used for data transfer in the virtual circuit network is
called _________.
a. Virtual circuit identifier
b. Global address
c. Network identifier
d. IP identifier
99. In Direct point to point communication adding the Nth computer requires
______ new connections
e. N^2
f. N-1
c. (N^2 -N)/2 page 23
d. N (N-1)
100. Which of the following is the correct function of bridge?
a. MTU path discovery
b. Byte stuffing
c. Routing information
d. Filtering and forwarding a frame page 50, 51
Point to point topology is
a. Size based
b. Mobility based
c. Connectivity based page 5
d. Medium based
101. IEEE LLC / SNAP header is ________which is used to specify the
type of date.
a. 8 octets google
b. 16 octets
c. 32 octets
d. 64octets
102. IEEE LLC / SNAP header is ________which is used to specify the
type of date.
a. CRC
b. Bit stuffing
c. Checksum
d. 2D Parity
103. What is the largest network in existence?
a. The internet google
b. A PAN
c. A Fog
d. Edge Network

0304-1659294 16

-
 ÂL-JÛÑÂÎD TÊCH
104. The frame format of any LAN technology must consists of ____
and___-
a. Payload and CRC
b. Frame header and CRC
c. Payload and Frame type
d. Frame header and payload page 36
105. ___________ can occur a LANs when a packet is delayed
because the network is busy
a. Jitter page 66
b. Loop
c. Deadlock
d. variance
106. Which of the following cannot be used to extend a LAN?
a. Repeaters
b. Switches
c. Routers
d. Fiber modems
107. Links-state algorithm is used in ___________
o RIP
o IGRP
o RIPv2
o OSPF page 64
108. According to size, there are ___classifications of networks
a. 2 page 2
b. 3
c. 4
d. 5
108. In which topology terminators are used at the end of the cable?
a. Star
b. Bus
c. Ring
d. Mesh
109. 1Switch simulates a _________LAN connecting segments
e. Single
f. Single shared
c. Bridged page 54
d. Complex
110. 1PVS stands for _____________
a. Permanent virtual circuit page 69
b. Private virtual circuit
c. Public virtual circuit

0304-1659294 17

-
 ÂL-JÛÑÂÎD TÊCH
d. Plastic virtual circuit
111. Hardware that calculates a CRC used two simple components _____
a. AND unit and XOR Unit
b. Shift register and XOR unit page 20
c. Shift register & AND unit
d. Shift register and Shift XCR unit
112. Thin ethernet is known as ________
a. 10 base 2 google
b. 10 base 5
c. 10 base T
d. All of the above
113. If a sender with a 1 Gigabit NIC and receiver with 100 Megabit NIC
wants to communicate with each other than at which speed they can
communicate
a. 11 Megabit
b. 100 Megabit
c. 1 Gigabit
d. 1.1 Gigabit
114. ____________ is used as an alternative of packet for a specific
computer network technology
e. Datum
f. Token
g. Ether
d. Frame page 14
115. The sharing of a medium and its link by two or more devices is called
____
a. Modulation
b. Encoding
c. Multiplexing
d. Line discipline
116. The topology each computer is connected to a central hub is called
e. Ring topology
b. Star topology page 5
c. Tree topology
d. Mesh topology
117. Asynchronous transfer mode (ATM) is designed to work on fiber but
can be used with _____________
a. wireless
b. Twisted pair page 72
c. Wifi
d. Bluetooth

0304-1659294 18

-
 ÂL-JÛÑÂÎD TÊCH
118. The basic responsibility of NIC is ________
a. To access medium network
b. To resource allocation
c. To access memory
d. All of the given option
119. 1Frame relay is ____
a. Connection oriented service page 64
b. Connectionless service
c. Typically ranges for 5 Mbps to 1000Mbps
d. Call based
120. The length of time required to send a variable length packet is ____
a. 5 second
b. Variable page 72
c. Constant
d. Fix
121. ABR stands for ______
a. Asynchronous bit rate
b. Asynchronous byte recovery
c. Asynchronous bit redundancy
d. Available bit rate page 71
122. In Token Ring, if all computers are ready to transmit it enforces
________access
a. First come first served
b. Round Robin page 30
c. Shorter delay
d. Last come first served
123. The Ethernet standard specifies that frames are sent using the
_________scheme.
a. Differential Manchester
b. Not Return to Zero (NR2)
c. Manchester Encoding page 27
d. Return to Zero (RZ)
124. ATM uses the concept of ___________.
a. Connection-oriented page 66
b. Connection-less
c. variable packet size
d. Fixed and variable packet size

0304-1659294 19

-
 ÂL-JÛÑÂÎD TÊCH
124. 1Which of the following is a benefit of point to point communication?
a. Quick to configure
b. Security implementation
c. Cost
d. Less availability
125. _________ is not used to extend LAN.
e. Hub
f. Fiber modem
g. Repeater
h. Bridge
126. Which types of VPNs are used for corporate connectivity across
companies residing in different geographical locations?
i. Remote access VPNs
j. Peer-to-peer VPNs
k. Country-to-country VPNs
d. Site-to-site VPNs google
127. Star topology is the kind of
o Tree topology
o b. Point-to-point topology page 05
o Broadcast topology
o Ring topology
127. In a __________ state, a bridge allows simultaneous use of each
segment.
o Ready
o Steady
o Final
o Startup
128. The network occupies larger areas like cities & countries is called
o LAN
o WAN
o MAN
o All of the above
129. In link state routing __________ send link-state information
about local connections.
o Bridges
o Switches
o Routers
o Hubs

0304-1659294 20

-
 ÂL-JÛÑÂÎD TÊCH
130. Transmission media are usually categorized as _______.
o Guided or unguided
o Fixed or unfixed
o Determinate or indeterminate
o Metallic or nonmetallic
131. Even parity can be used to check for ________ bit/ bits of errors.
o a. 1 page 18
o 2
o 3
o 0
132. Routing table entries can be ________ with a default route.
• Collapsed
• Redirected
• Emerged
• Guaranteed
133. The system administrator must coordinate to avoid the conflict in
_________ hardware addressing scheme.
a. Static
b. Dynamic
c. Configurable
d. Fixed
134. ____________ network does not depend on CSMA/CD.
o Ethernet
o Fast Ethernet
o Gigabit Ethernet
o Wireless
135. Which of the following technologies can extend the diameter of
LAN medium?
o Fiber optic
o Repeater
o Diameter of LAN medium is not extendable
o Both. Fiber optic and Repeaters
136. Connections are formed in Asynchronous transfer mode by starting
values in________ in ATM switches, as opposed to making actual electrical
connections.
o Heap
o Stack
o Virtual Circuit
o d. Memory locations page 67

0304-1659294 21

-
 ÂL-JÛÑÂÎD TÊCH
137. The _______ scheme must be reliable to prevent conflicts. a. Static
b. Dynamic page 34
c. Configurable
d. Fixed
138. Metropolitan area network is used for ____________.
a. City page 55
b. Building
c. Country
d. Continent
139. Which addressing can be only used in the local area networks?
o a. IP google
o Physical
o Port
o Protocol
139. The sharing of a _______ among the workers in an office is a goal of resource
sharing.
a. Mouse
b. Printer page 9
c. Keyboard
d. Motherboard
140. ATM uses fixed size, small cells, 48 octet's data and __________.
a. 3 Octets header
b. 5 Octets header page 65
c. 6 Octets header
d. 7 Octets header
141. Which of the followings is not an advantage of framing?
a. Missing eot indicates sending computer crashed
b. Missing soh indicates receiving computer missed beginning of message
c. Delimiters do not contain any user data page 16
d. Bad frame is discarded
142. The _________ field of Ethernet frame has the purpose of receiver
synchronization.
a. Preamble page 36
b. Frame Type
c. Data
d. CRC

0304-1659294 22
 ÂL-JÛÑÂÎD TÊCH
Q1: Internet Standards Specifies that any two stations cannot be
separated by more than __________ Repeaters.
A) Three
B) Four (100% Sure)
C) Five
D) Six

Q2: A typical port on an ATM switch operates at __________ or higher.

A) OC-2 speed (155Gbps)
B) OC-2 speed (1000Mbps)
C) OC-3 speed (155Mbps) (100% Sure)
D) OC-3 speed (100Gbps)

Q3: Ethernet uses a __________ bit static addressing scheme in which

each device is assigned a unique address by the manufacturer.
A) 64
B) 48 (100% Sure)
C) 32
D) 8

Q4: Which one is incorrect statement?

A) Hub wiring centralizes electronics and connections. It makes
management easier.
B) No Transceiver allows computer to be powered off or disconnected
from network without distracting other communication. (100% Sure)
C) Transceiver may be located in an inconvenient place in any situation
D) None of these

Q5: ATM is also called __________.

A) Label rewriting
B) Label switching system
C) label rewriting and label switching system
D) All of above (100% Sure)
-

0304-1659294 23
 ÂL-JÛÑÂÎD TÊCH
Q6: The most important task a bridge performs is __________.
A) Packet switching
B) Line controlling
C) Noise controlling
D) Frame filtering (100% Sure)

Q7: Which of the following statement is true regarding Jitter?

A) Jitter is used for variance in transmission delays.
B) Jitter can occur when a packet is delayed.
C) Jitter is significance for voice, video and data
D) All of the obove (100% Sure)

Q8: Which of the following is a benifit of source independence?

A) It allows fast and efficient routing
B) Packet switch do not need to have complete information about all
destinations
C) Network functions even if topology changes
D) All of the above (100% Sure)

Q9: The term signaling is used to describe __________.

A) Communication about the internet
B) Communication about the extranet
C) Communication about the network (100% Sure)
D) None of above
Question No: 1
No error detection scheme is perfect because transmission errors can affect the additional information as
well asthe data.

► True
► False

Question No: 2
------ Program sends a message to a remote computer and reports whether the computer responds.
-

0304-1659294 24
 ► Ping
ÂL-JÛÑÂÎD TÊCH
► Traceroute
► ICMP
► Non of the given

Question No: 3 ---------- was especially concerned about the lack of high powered computers.

► ARPA (Computer Networks and Internets, page5)

► IEEE
► EIA
► Non of the given

Question No: 4
The term ----- is used to denote the definition of a packet used with a specific type of network.
► Packet
► Frame (Computer Networks and Internets, page 73)
► Data
► None of the given
Question No: 5
Computer networks are often called ----------- because they use packet technology.

► Ethernet
► Switch networks
► Packet networks (Computer Networks and Internets, page 73)
► None of the given

Question No: 6
-------------- have advantages arisen from the size and ease of computation.

► CRC
► Parity(Page 19)
► Checksums
► None of given

Question No: 7
Most LANs that employ ring topology use an access mechanism known as-------

► CSMA/CD
► CSMA/CA
► TOKEN PASSING (Computer Networks and Internets, page95)
► None of the given
-

0304-1659294 25
 ÂL-JÛÑÂÎD TÊCH
Question No: 8 ( M a r k s: 1 )
IEEE LLC/SNAP header is ---- , which is used to specify the type of data.

► 8 octets
► 8 bytes
► 8 bits
► None of the given
Question No: 9
Formally named informally known as the twisted pair Ethernet or TP Ethernet.

► 10 Base 2
► 10 Base 5
► 10 Base T (Page 43)
► None of the given
Question No: 10
An interface for twisted pair Ethernet must have an connector , and must generate signalsaccording to
the specification.

► RJ-45, 10 Base T(Computer Networks and Internets, page 126)

► RJ-45, 10 Base 5
► BNC, 10 Base 2
► BNC, 10 Base T

Question No: 11
A bridges function in the layers(s).

► Physical (MAC)
► Data link
► Network
► Physical (MAC) and Data link

Question No: 12
A Bridge can

► Filter a frame
► Forward a frame
► Extend a LAN
► Do all the above
-

0304-1659294 26
 ÂL-JÛÑÂÎD TÊCH
Question No: 13
A Bridge forwards or filters a frame by comparing the information in its address table to the frame’s

► Layer 2 source address

► Source node’s physical address
► Layer 2 destination address
► Layer 3 destination address

Question No: 14
computes shortest paths in a graph by using weights on edges as a measure of distance.
► Greedy algorithm
► Distance vector algorithm
► Dijksta’s algorithm(Computer Networks and Internets, page112)
► Non of the given
Question No: 15
is used for audio and video, since these have predefined maximum data rates

► Constant Bit Rate (CBR) service (Page 71)

► Variable Bit Rate (VBR) service
► Available Bit Rate (ABR) service
► None of the given

Question No: 16
Unlike Frame Relay and ATM, SMDS (Switched multi-megabit Data service) offers .

► Connectionless service paradigm (Computer Networks and Internets, page112)

► Connection oriented service paradigm
► Both Connectionless and Connection-oriented service paradigm
► None of the given

Question No: 17
A network with throughput T and delay D has a total of bit in transit at any time.

►T/D
► T x D (Computer Networks and Internets, page203)
►T+D
► None of the given
-

0304-1659294 27
 ÂL-JÛÑÂÎD TÊCH
Question No: 18
ATM is designed to work on .

► Twisted Pair
► Coaxial
► Radio Frequency
► Fiber (Computer Networks and Internets, page 72)

Question No: 19
Computers attached to an Ethernet use --- in which a computer waits for the ether to be idle before
transmitting a frame.

► CSMA/CD(Computer Networks and Internets, page 93)

► CSMA/CA
► TOKEN PASSING
► None of the given
Question No: 20
FDDI can transmits data at a rate of ----------

► 100 million bits per second (Page 314)

► 10 million bits per second
► 1000 million bits per second
► None of the given

Question No: 21
In Point-to-Point topology there are two topologies.

► Star and Tree

► Tree and Ring
► Star and Ring
► Star and Tree (Page 5)
► None of the given

Question No: 22
------ Program sends a message to a remote computer and reports whether the computer responds.

► Ping (Computer Networks and Internets, page9)

► Traceroute
► ICMP
► Non of the given
-

0304-1659294 28
 ÂL-JÛÑÂÎD TÊCH
Question No: 23
------ has no way to determine the cause of the problem.

► ICMP
► Ping (Computer Networks and Internets, page 11)
► Trace route
► Non of the given
Question No: 24
The term ---------refers to the general concept of a small block of data

► Packet (Page 16)

► Frame
► Data
► None of the given

Question No: 25
---------- scheme, which is designed to help detect transmissions errors, send one extra bit of information
witheach character

► Parity (Computer Networks and Internets, page 77)

► Checksums
► CRC
► None of given

Question No: 26
Local Talk is a LAN technology that employs -------------

► Bus topology (Page 30)

► Ring topology
► Star topology
► None of the given

Question No: 27
Most LANs that employ ring topology use an access mechanism known as-------

► CSMA/CD
► CSMA/CA
► TOKEN PASSING (Computer Networks and Internets,
page95)
► None of the given
-

0304-1659294 29
 ÂL-JÛÑÂÎD TÊCH
Question No: 28
Ethernet uses a --- bit static addressing scheme in which each device is assigned a unique address by the
manufacturer.

► 64
► 48 (Computer Networks and Internets, page 109)
► 32
►8

0304-1659294 30
 ÂL-JÛÑÂÎD TÊCH
Question No: 29
Formally named informally known as the thick wire Ethernet or Thick net.

► 10 Base 2
► 10 Base 5 Computer Networks and Internets, page 120)
► 10 Base T
► None of the given

Question No: 30
Formally named informally known as the twisted pair Ethernet or TP Ethernet.

► 10 Base 2
► 10 Base 5
► 10 Base T (Page 43)
► None of the given

Question No: 31
The maximum size of an Ethernet segment is

► 250 meters
► 500 meters (Page 27)
► 700 meters
► None of the given

Question No: 32
A Bridge can

► Filter a frame
► Forward a frame
► Extend a LAN
► Do all the above

Question No: 33
computes shortest paths in a graph by using weights on edges as a measure of
distance.

► Greedy algorithm
► Distance vector algorithm

0304-1659294 31

-
 ÂL-JÛÑÂÎD TÊCH
► Dijksta’s algorithm (Computer Networks and Internets, page112)

Question No: 34
is used for compressed audio and video where the data rate depends on the
level of compressionthat can be achieved.

► Constant Bit Rate (CBR) service

► Variable Bit Rate (VBR) service (Page 71)
► Available Bit Rate (ABR) service
► None of the given

Question No: 35
Basic LAN technologies such as Ethernet, Token Ring, and FDDI use a .

► Connectionless service paradigm (Computer Networks and Internets, page112)

► Connection-oriented service paradigm
► Both Connectionless and Connection-oriented service paradigm
► None of the given

Question No: 36
The product of delay and throughput measures the of data that can be present on the
network.

► Area
► Volume (Page 80)
► Length
► None of the given

Question No: 37
A network with throughput T and delay D has a total of bit in transit at any time.

►T/D
► T x D (Computer Networks and Internets, page203) rep
►T+D
► None of the given

Question No: 38
One repeater two repeaters the maximum cable length limitation.

0304-1659294 32

-
 ÂL-JÛÑÂÎD TÊCH
► doubles, triple (Page 49)
► square roots, cude roots
► and, triple
► doubles, cancel
Question No: 39
A network uses a------- if all computers attach to a central point

► Star Topology (Page 25)

► Ring Topology
► Bus Topology
► None of the given

Question No: 40
Computers attached to an Ethernet use ------- in which a computer waits for the other to be idle
before
transmitting a frame.

► CSMA/CD (Computer Networks and Internets, page 93)

► CSMA/CA
► TOKEN PASSING
► None of the given

0304-1659294 33