Total No. of Questions : 8] SEAT No.

8
23
P-9090 [Total No. of Pages : 2

ic-
[6179]-215

tat
8s
S.E. (Electrical Engineering)

3:3
02 91
FUNDAMENTALS OF MICROCONTROLLER AND

9:3
APPLICATIONS

0
30
6/1 13
(2019 Pattern) (Semester - IV) (203149)
0
2/2
.23 GP

Time : 2½ Hours] [Max. Marks : 70

Instructions to the candidates :
E
82

1) Solve Q1 or Q2, Q3 or Q4, Q5 or Q6, Q7 or Q8.

8
C

23
2) Figures to the right indicate full marks.

ic-
3) Neat diagrams must be drawn wherever necessary.
16

tat
4) Assume suitable additional data, if necessary.
8.2

8s
5) Use of non-programmable calculator is allowed.
.24

3:3
91
49

9:3
30

Q1) a) Write Short note on Data Types in C. [4]

30
01
02

b) Draw& explain TMOD register. [6]

2/2
GP

c) Write a C program to generate square wave of 50Hz frequency with

6/1

50 % duty cycle on pin 2.3. Assume XTAL = 11.0592MHz & use

CE
82

timer 0 in mode 1. [8]

8
23
.23

OR
ic-
16

tat
Q2) a) Explain Timer mode 0 & mode 1 of 8051 Microcontroller. [4]
8.2

8s
.24

b) Draw & explain TCON register. [6]

3:3
91
49

9:3

c) Write C Program to toggle bit P1.5 of port P1,50000 times. [8]

30
30
01
02

Q3) a) Explain Interrupt Priority Register of 8051 Microcontroller. [3]

2/2
GP

b) Explain interrupt structure of 8051 microcontroller with neat diagram.

6/1
CE

[6]
82
.23

c) With the help of neat diagram explain interfacing of ADC 0809 with
8051 microcontrollers. [8]
16
8.2

OR
.24
49

P.T.O.
Q4) a) Explain the SOC, EOC & OF pin of ADC 0809. [3]

8
23
b) Write short note on Interrupt enable register. [6]

ic-
c) Write a program to turn off LED for connected to Port 0 when interrupt

tat
0 occurs and turn it on when interrupt 1 occurs. [8]

8s
3:3
02 91
9:3
Q5) a) Explain Steps to transfer Data Serially in 8051 microcontroller. [4]

0
30
b) 6/1 13
Write Short note on SCON register. [6]
0
2/2
c) Write program to transfer letter ‘T’ serially 10 times at baud rate of
.23 GP

4800. Use serial port in mode 1. XTAL = 12MHz. [8]

E
82

8
OR
C

23
ic-
Q6) a) Explain Steps to receive Data Serially in 8051 microcontroller. [4]
16

tat
b) Write short note AT commands required for GSM. [6]
8.2

8s
.24

c) Explain Serial port structure of 8051 microcontroller. [8]

3:3
91
49

9:3
30
30

Q7) a) What is Step Angle ? Calculate the steps required to complete one
01
02

revolution for 1.2 degree step angle stepper motor. [3]

2/2
GP

b) Explain LED interfacing with 8051 microcontroller. [6]

6/1
CE

c) With the help of block diagram explain Power measurement using

82

8
23
8051. [8]
.23

OR ic-
16

tat
8.2

8s

Q8) a) What are the applications of relay? [3]

.24

3:3

b) With the help of block diagram explain Voltage & current measurement
91
49

9:3

using 8051. [6]

30
30

c) Draw interfacing diagram of a stepper motor with 8051 and write

01
02

program to rotate stepper motor 360 Degree in anticlockwise direction

2/2
GP

with step angle of 1.8 degree. [8]

6/1
CE
82


.23
16
8.2
.24
49

[6179]-215 2