Sharp Service Manual
Uploaded by
cooldude.pesiganSharp Service Manual
Uploaded by
cooldude.pesiganLC-40/46/52/60LE835U/830U/832U/LC-60LE831U
SERVICE MANUAL
No. S21M760LE835U
LCD COLOR TELEVISION
LC-60LE831U
LC-40/46/52/60LE835U
LC-40/46/52/60LE830U
MODELS LC-40/46/52/60LE832U
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
SAFETY PRECAUTION [4] REMOVING OF MAJOR PARTS
IMPORTANT SERVICE SAFETY PRECAUTION...............i (LC-60LE835U/830U/831U/832U)...............4-16
PRECAUTIONS A PRENDRE LORS DE [5] The location putting on the heat measure sheet......4-21
LA REPARATION ...............................................ii [6] Precautions for assembly ............................4-24
PRECAUTIONS FOR USING LEAD-FREE SOLDER........... iii [7] The way of detaching Rear Cabinet ............4-26
OUTLINE CHAPTER 5. ADJUSTMENT
MAJOR SERVICE PARTS ................................iv [1] ADJUSTMENT PROCEDURE ......................5-1
[2] PUBLIC MODE SETTING PROCEDURE.......5-16
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS (LC-40/46LE835U/830U/832U)......... 1-1 CHAPTER 6. TROUBLESHOOTING TABLE
[2] SPECIFICATIONS (LC-52/60LE835U/ [1] Failure diagnosis by LED in front of cabinet ........6-1
830U/832U/LC-60LE831U) ............................ 1-2 [2] LED flashing specification at the time of an
error (Center icon LED used) ........................6-1
CHAPTER 2. OPERATION MANUAL [3] TROUBLESHOOTING TABLE ......................6-5
[1] Parts Name .................................................... 2-1
[2] OPERATION MANUAL .................................. 2-3 CHAPTER 7. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS .........................7-1
CHAPTER 3. DIMENSIONS
[1] DIMENSIONS (LC-40LE835U/830U/832U)........ 3-1 CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK DIAGRAM
[2] DIMENSIONS (LC-46LE835U/830U/832U)........ 3-2 [1] OVERALL WIRING DIAGRAM
[3] DIMENSIONS (LC-52LE835U/830U/832U)........ 3-3 (LC-40/46/52/60LE835U) ..............................8-1
[4] DIMENSIONS (LC-60LE835U/830U/831U/832U)........ 3-4 [2] OVERALL WIRING DIAGRAM (LC-40/46/
52/60LE830U/832U/LC-60LE831U) ..............8-2
CHAPTER 4. REMOVING OF MAJOR PARTS [3] SYSTEM BLOCK DIAGRAM
[1] REMOVING OF MAJOR PARTS (LC-40/46/52/60LE835U) ..............................8-3
(LC-40LE835U/830U/832U)........................... 4-1 [4] SYSTEM BLOCK DIAGRAM (LC-40/46/
[2] REMOVING OF MAJOR PARTS 52/60LE830U/LE832U/LC-60LE831U)..........8-4
(LC-46LE835U/830U/832U)........................... 4-6
[3] REMOVING OF MAJOR PARTS Parts Guide
(LC-52LE835U/830U/832U)......................... 4-11
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
LC-40LE830U
SAFETY PRECAUTION Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
WARNING • Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15µF capacitor in series with all exposed metal cabinet
1. For continued safety, no modification of any circuit should be parts and a known earth ground, such as electrical conduit or elec-
attempted.
trical ground connected to an earth ground.
2. Disconnect AC power before servicing. • Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
C A U T I O N : F O R C O N T I N U E D PROTECTION • Connect the resistor connection to all exposed metal parts having a
AGAINST A RISK OF FIRE REPLACE ONLY WITH return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
SAME TYPE FUSE. drop across the resistor.
F7001 (250V 5A) All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
BEFORE RETURNING THE RECEIVER (Fire &
DVM
Shock Hazard)
AC SCALE
Before returning the receiver to the user, perform the following
safety checks: 1.5k ohm
3. Inspect all lead dress to make certain that leads are not pinched, 10W
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
0.15 µF
covers or shields, isolation resistor-capacitor networks, mechanical
TEST PROBE
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
• Plug the AC cord directly into a 120 volt AC outlet.
TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
GROUND
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have For continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
These characteristics are often not evident from visual inspection, nor The use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the Replacement Parts List
and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
i
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux
conseils suivants.
AVERTISSEMENT • A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ
10 watts en parallèle avec un condensateur de 0.15µF en série
1. N'entreprendre aucune modification de tout circuit. C'est danger- avec toutes les pièces métalliques exposées du coffret et une terre
eux. connue comme une conduite électrique ou une prise de terre
2. Débrancher le récepteur avant toute réparation. branchée à la terre.
• Utiliser un voltmètre CA d'une sensibilité d'au moins 5000Ω/V pour
mesurer la chute de tension en travers de la résistance.
PRECAUTION: POUR LA PROTECTION CON-
• Toucher avec la sonde d'essai les pièces métalliques exposées qui
TINUE CONTRE LES RISQUES D'INCENDIE,
présentent une voie de retour au châssis (antenne, coffret métalli-
REMPLACER LE FUSIBLE que, tête des vis, arbres de commande et des boutons, écusson,
etc.) et mesurer la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir inversé la
F7001 (250V 5A)
fiche du cordon d'alimentation. (Si nécessaire, une prise
d'adpatation non polarisée peut être utilisée dans le but de termin-
er ces vérifications.)
La tension de pointe mesurèe ne doit pas dépasser 0.75V (corre-
spondante au courant CA de pointe de 0.5mA).
Dans le cas contraire, il y a une possibilité de choc électrique qui
doit être supprimée avant de rendre le récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET LE
CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer les vérifica- DVM
tions suivantes.
ECHELLE CA
3. Inspecter tous les faisceaux de câbles pour s'assurer que les fils
1.5k ohm
ne soient pas pincés ou qu'un outil ne soit pas placé entre le châs- 10W
sis et les autres pièces métalliques du récepteur.
4. Inspecter tous les dispositifs de protection comme les boutons de
commande non-métalliques, les isolants, le dos du coffret, les cou-
vercles ou blindages de réglage et de compartiment, les réseaux
de résistancecapacité, les isolateurs mécaniques, etc. 0.15 µF
SONDE D'ESSAI
5. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la
fuite de courant, de la facon suivante:
• Brancher le cordon d'alimentation directem-ent à une prise de cou-
rant de 120V. (Ne pas utiliser de transformateur d'isolation pour AUX PIECES BRANCHER A UNE
cet essai). METALLIQUES TERRE CONNUE
EXPOSEES
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les télévi- Pour assurer la protection, ces pièces doivent être identiques à celles
seur ACL présentent des caractéristiques spéciales relatives à la sé- utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas
curité, qui ne sont souvent pas évidentes à vue. Le degré de protec- les mêmes caractéristiques que les pièces recommandées par l'usine,
tion ne peut pas être nécessairement augmentée en utilisant des indiquées dans ce manuel, peut provoquer des électrocutions, incen-
pièces de remplacement étalonnées pour haute tension, puissance, dies, radiations X ou autres accidents.
etc.
Les pièces de remplacement qui présentent ces caractéristiques sont
identifiées dans ce manuel; les pièces électriques qui présentent ces
particularités sont identifiées par la marque " " et hachurées dans la
liste des pièces de remplacement et les diagrammes schématiques.
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
ii
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Employing lead-free solder
• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Using lead-free wire solder
• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J φ0.3mm 250g (1roll)
ZHNDAi126500E BK J φ0.6mm 500g (1roll)
ZHNDAi12801KE BM J φ1.0mm 1kg (1roll)
iii
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
LC-40LE830U
OUTLINE Service Manual
MAJOR SERVICE PARTS
PWB Unit
Ref No. Parts No. Description
N DKEYMF733FM16 MAIN Unit (LC-40LE835U)
N DKEYMF733FM14 MAIN Unit (LC-46LE835U)
N DKEYMF733FM13 MAIN Unit (LC-52LE835U)
N DKEYMF733FM12 MAIN Unit (LC-60LE835U)
N DKEYMF733FM04 MAIN Unit (LC-40LE830U)
N DKEYMF733FM03 MAIN Unit (LC-46LE830U)
N DKEYMF733FM02 MAIN Unit (LC-52LE830U)
N DKEYMF733FM01 MAIN Unit (LC-60LE830U)
N DKEYMF733FM18 MAIN Unit (LC-60LE831U)
N DKEYMF733FM10 MAIN Unit (LC-40LE832U)
N DKEYMF733FM08 MAIN Unit (LC-46LE832U)
N DKEYMF733FM07 MAIN Unit (LC-52LE832U)
N DKEYMF733FM06 MAIN Unit (LC-60LE832U)
N DUNTKF494FM01 R/C, Operation Unit
N DUNTKF770FM03 ICON Unit (LC-40/46/52/60LE835U)
N DUNTKF770FM02 ICON Unit (LC-40/46/52/60LE830U/832U/LC-60LE831U)
N RUNTKA810WJQZ WiFi Unit
N RUNTKA811WJQZ Touch Sensor Unit (LC-40/46/52/60LE835U)
N RUNTKA812WJQZ Touch Sensor Unit (LC-40/46/52/60LE830U/832U/LC-60LE831U)
N RUNTKA819WJQZ IR Emitter Unit (LC-40/46/52/60LE835U Only)
N RUNTKA786WJQZ POWER/LED Drive Unit (LC-40LE835U/830U/832U)
N RUNTKA790WJQZ POWER/LED Drive Unit (LC-46LE835U/830U/832U)
N RUNTKA794WJQZ POWER/LED Drive Unit (LC-52LE835U/830U/832U)
N RUNTKA798WJQZ POWER/LED Drive Unit (LC-60LE835U/830U/831U/832U)
N RUNTK4909TPZS LCD Control Unit (LC-40LE835U)
N RUNTK4909TPZW LCD Control Unit (LC-46LE835U)
N RUNTK4909TPZF LCD Control Unit (LC-52LE835U)
N RUNTK4909TPZA LCD Control Unit (LC-60LE835U)
N RUNTK4910TPZE LCD Control Unit (LC-40LE830U/832U)
N RUNTK4910TPZC LCD Control Unit (LC-46LE830U/832U)
N RUNTK4910TPZB LCD Control Unit (LC-52LE830U/832U)
N RUNTK4910TPZZ LCD Control Unit (LC-60LE830U/831U/832U)
NOTE: *1 Replace MAIN PWB Units (DKEYMF733FM**) in case of IC8401, IC3303 or IC8455 failure.
*2 Touch Sensor Unit reuse will be impossible, once it is stuck on front Cabinet and exfoliates.
OTHER Unit
Ref No. Parts No. Description
N R1LK400D3GW50Z 40" LCD Panel Module Unit (LK400D3GW50Z) (LC-40LE835U)
N R1LK460D3GW40Z 46" LCD Panel Module Unit (LK460D3GW40Z) (LC-46LE835U)
N R1LK520D3GW40Z 52" LCD Panel Module Unit (LK520D3GW40Z) (LC-52LE835U)
N R1LK600D3GW40Z 60" LCD Panel Module Unit (LK600D3GW40Z) (LC-60LE835U)
N R1LK400D3GW80Z 40" LCD Panel Module Unit (LK400D3GW80Z) (LC-40LE830U/832U)
N R1LK460D3GW80Z 46" LCD Panel Module Unit (LK460D3GW80Z) (LC-46LE830U/832U)
N R1LK520D3GW80Z 52" LCD Panel Module Unit (LK520D3GW80Z) (LC-52LE830U/832U)
N R1LK600D3GW30Z 60" LCD Panel Module Unit (LK600D3GW30Z) (LC-60LE830U/831U/832U)
IC For Exclusive Use Of The Service
Ref No. Parts No. Description Q'ty
IC2001 RH-iXD241WJN1Q IC R5F21368CNFP (Monitor Microcomputer) 1
iv
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
Service Jigs
Ref No. Parts No. Description Q'ty
N QCNW-C222WJQZ Connecting Cord L=1000mm 80pin LCD Control Unit to LCD Panel Unit 2
QCNW-L214WJQZ Connecting Cord L=1000mm 64pin LCD Control Unit to LCD Panel Unit (LC-40/46/52/60LE835U
N 2
Only)
N QCNW-F676WJQZ Connecting Cord L=1000mm 41pin Main to LCD Control Unit (LW) 1
N QCNW-G405WJQZ Connecting Cord L=1000mm 4pin Main to LCD Control Unit (PL) 1
N QCNW-L795WJQZ Connecting Cord L=1000mm 24pin Main to POWER/LED Drive Unit (PD) 1
v
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 1. SPECIFICATIONS
LC-40LE830U
Service Manual
[1] SPECIFICATIONS (LC-40/46LE835U/830U/832U)
Item Model: LC-40LE835U/830U/832U Model: LC-46LE835U/830U/832U
LCD Size 40" Class (40" Diagonal) 46" Class (45 63/64" Diagonal)
panel Resolution 2,073,600 pixels (1,920 x 1,080)
TV-standard (CCIR) American TV Standard ATSC/NTSC System
VHF/UHF VHF 2-13ch, UHF 14-69ch
CATV 1-135ch (non-scrambled channel only)
TV Receiving Digital Terrestrial
Function Channel 2-69ch
Broadcast (8VSB)
Digital cable*1
1-135ch (non-scrambled channel only)
(64/256 QAM)
Audio multiplex BTSC System
Audio out 10W x 2 + 15 W (WF)
HDMI 1 HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
HDMI 2 HDMI in with HDCP
Back panel HDMI 3 HDMI in with HDCP
vertical
inputs HDMI 4 HDMI in with HDCP
AUDIO OUT Audio out (Ø 3.5 mm stereo jack)
USB 1 Photo/Music/Video mode, Software update
COMPONENT COMPONENT in
VIDEO 1 AV in
Terminals Back panel VIDEO 2 AV in
surface
inputs ANALOG RGB (PC) in (15-pin mini D-sub female connector),
PC IN
Audio in (Ø 3.5 mm stereo jack)
RS-232C 9-pin D-sub male connector
ANT/CABLE 75 Ω Unbalance, F Type x 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
AUDIO IN Audio in (Ø 3.5 mm stereo jack)
Back panel
horizontal DIGITAL AUDIO OUTPUT Optical Digital audio output x 1 (PCM/Dolby Digital)
inputs
ETHERNET Network connector
USB 2 Photo/Music/Video mode, Software update
OSD language English/French/Spanish
Power Requirement AC 120 V, 60 Hz
Power Consumption 120 W (0.1 W Standby with AC 120 V) (LE835U) 150 W (0.1 W Standby with AC 120 V) (LE835U)
118 W (0.1 W Standby with AC 120 V) (LE830U/832U) 142 W (0.1 W Standby with AC 120 V) (LE830U/832U)
TV + stand 36.4 lbs./16.5 kg 50.7 lbs./23.0 kg
Weight
TV only 29.8 lbs./13.5 kg 41.9 lbs./19.0 kg
Dimension *2 TV + stand 36 15/16 x 25 3/64 x 10 25/64 inch 42 13/64 x 28 x 11 35/64 inch
(W x H x D) TV only 36 /16 x 23 /32 x 1 /8 inch
15 5 5
42 13/64 x 26 7/64 x 1 5/8 inch
Operating temperature +32°F to +104°F (0°C to +40°C)
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the front panel to malfunction.
Storage temperature: -4°F to +140°F (-20°C to +60°C)
1–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] SPECIFICATIONS (LC-52/60LE835U/830U/832U/LC-60LE831U)
Item Model: LC-52LE835U/830U/832U Model: LC-60LE835U/830U/831U/832U
LCD Size 52" Class (52 1/32" Diagonal) 60" Class (60 1/32" Diagonal)
panel Resolution 2,073,600 pixels (1,920 x 1,080)
TV-standard (CCIR) American TV Standard ATSC/NTSC System
VHF/UHF VHF 2-13ch, UHF 14-69ch
CATV 1-135ch (non-scrambled channel only)
TV Receiving Digital Terrestrial
Function Channel 2-69ch
Broadcast (8VSB)
Digital cable*1
1-135ch (non-scrambled channel only)
(64/256 QAM)
Audio multiplex BTSC System
Audio out 10W x 2 + 15 W (WF)
HDMI 1 HDMI in with HDCP, Audio in (Ø 3.5 mm stereo jack)
HDMI 2 HDMI in with HDCP
Back panel HDMI 3 HDMI in with HDCP
vertical
inputs HDMI 4 HDMI in with HDCP
AUDIO OUT Audio out (Ø 3.5 mm stereo jack)
USB 1 Photo/Music/Video mode, Software update
COMPONENT COMPONENT in
VIDEO 1 AV in
Terminals Back panel VIDEO 2 AV in
surface
inputs ANALOG RGB (PC) in (15-pin mini D-sub female connector),
PC IN
Audio in (Ø 3.5 mm stereo jack)
RS-232C 9-pin D-sub male connector
ANT/CABLE 75Ω Unbalance, F Type x 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
AUDIO IN Audio in (Ø 3.5 mm stereo jack)
Back panel
horizontal DIGITAL AUDIO OUTPUT Optical Digital audio output x 1 (PCM/Dolby Digital)
inputs
ETHERNET Network connector
USB 2 Photo/Music/Video mode, Software update
OSD language English/French/Spanish
Power Requirement AC 120 V, 60 Hz
Power Consumption 170 W (0.1 W Standby with AC 120 V) (LE835U) 220 W (0.1 W Standby with AC 120 V) (LE835U)
162 W (0.1 W Standby with AC 120 V) (LE830U/832U) 213 W (0.1 W Standby with AC 120 V) (LE830U/831U/832U)
TV + stand 61.7 lbs./28.0 kg 83.8 lbs./38.0 kg
Weight
TV only 52.9 lbs./24.0 kg 68.3 lbs./31.0 kg
Dimension *2 TV + stand 47 31/64 x 30 63/64 x 11 35/64 inch 54 29/64 x 34 31/32 x 14 27/64 inch
(W x H x D) TV only 47 /64 x 29 /16 x 1 /8 inch
31 1 5
54 29/64 x 33 1/32 x 1 5/8 inch
Operating temperature +32°F to +104°F (0°C to +40°C)
*1
Emergency alert messages via Cable are unreceivable.
*2
The dimensional drawings are shown on the inside back cover.
The dimensions include projecting parts.
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
1–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 2. OPERATION MANUAL
LC-40LE830U
Service Manual
[1] Parts Name
TV (Front)
3D Model Only
Center Icon illumination
3D infrared emitter *1
OPC sensor *2
Remote control sensor VOL / CH / INPUT MENU POWER *3
*1 This panel emits the infrared signal towards the 3D Glasses you wear when you view 3D images.
Do not place anything between the 3D infrared emitter on the TV and the infrared receiver on the
3D Glasses. (3D Model: LC-40/46/52/60LE835U Only)
*2 OPC: Optical Picture Control.
*3 for using the touch sensor panel.
TV (Rear)
*1
RS-232C terminal
PC IN terminal
VIDEO 2 terminals
VIDEO 1 terminals
COMPONENT
terminals
*1
AUDIO OUT terminal
*1
USB 1 terminal
HDMI 1 terminal
ARC: Audio Return Channel
HDMI 2 terminal
USB 2 Antenna/
terminal Cable in
HDMI 3 terminal
DIGITAL AUDIO
ETHERNET OUTPUT terminal
terminal AUDIO IN terminal HDMI 4 terminal
(shared for PC IN
and HDMI 1) *2
*1 for external equipment connection.
*2 for details on the Audio Select function.
2–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
1 POWER: Switch the TV power on or enter standby.
Remote Control Unit 2 TV, STB, DVD•VCR, AUDIO: Switches the remote
control for TV, STB, DVD, BD, VCR and AUDIO operation.
1 * To enter the code registration mode, you need to press
an appropriate button (STB, DVD•VCR or AUDIO) and
DISPLAY at the same time.
18 3 External equipment operational buttons: Operate the
19 external equipment.
2 4 OPTION: Display the Link Operation Menu screen. This
button will function only when AQUOS LINK is used.
5 SLEEP: Set the sleep timer.
3
6 0–9: Set the channel.
7 •(DOT):
4 20 8 CC: Display captions from a closed-caption source.
5 21 9 AV MODE: Select an audio or video setting.
10 MUTE: Mute the sound.
6 11 VOL / : Set the volume.
12 MENU: Display the menu screen.
13 3D: Select between 3D and 2D image viewing.
(3D Model : LC-40/46/52/60LE835U Only)
7 22 14 / / / ,ENTER: Select a desired item on the screen.
15 EXIT: Turn off the menu screen.
8 23 16 FAVORITE CH: Set the favorite channels.
9 24
17 A, B, C, D: Select 4 preset favorite channels in 4 different
10 25 categories.
11 26 While watching, you can toggle the selected channels by
12 pressing A, B, C and D.
18 DISPLAY: Display the channel information.
13 27 19 POWER (SOURCE): Turns the power of the external
3D Model Only equipment on and off.
20 FREEZE: Set the still image. Press again to return to
14 normal screen.
21 POWER SAVING: Select Power Saving settings.
15 28 22 ENT: Jumps to a channel after selecting with the 0–9
29 buttons.
16 23 FLASHBACK: Return to the previous channel or external
17 input mode.
24 VIEW MODE: Select the screen size.
25 INPUT: Select a TV input source. (TV, HDMI1, HDMI2,
HDMI3, HDMI4, COMPONENT, VIDEO1, VIDEO2, PC IN,
Home Network (DLNA), USB)
26 CH / : Select the channel.
27 APPS: Display the application window.
28 RETURN: Return to the previous menu screen.
29 FAV APP 1, 2, 3: You can assign your favorite
applications to these buttons.
• When using the remote control unit, point it at the TV.
2–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] OPERATION MANUAL
QUICK REFERENCE
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
• Attach the stand in the correct direction.
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
LC-40LE835U/830U/832U
1 Confirm that there are 7 screws (3 long screws, 3 4 Insert and tighten the 3 screws into the 3 holes on
middle screws and 1 short screw) supplied with the the rear of the stand unit.
stand unit.
Middle screws
2 Attach the supporting post for the stand unit onto
the base as shown below.
• The supporting post attaches to the base at an off-
centered location on the base. Be sure to attach the
supporting post in the direction indicated below and
attach the stand to the TV with the wider side of the
base facing forward.
2
Long screws
5 1 Insert the stand cover.
2 Insert the screw to secure the stand cover.
Short screw
Forward 1
3 Insert the stand into the openings on the rear of the
TV.
Soft cushion
• To detach the stand, perform the steps in reverse
order.
2–3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
LC-46LE835U/LC-52LE835U/830U/832U
1 Confirm that there are 9 screws (4 long screws, 4 4 Insert and tighten the 4 screws into the 4 holes on
middle screws and 1 short screw) supplied with the the rear of the stand unit.
stand unit.
Middle screws
2 Attach the supporting post for the stand unit onto
the base as shown below.
• The supporting post attaches to the base at an off-
centered location on the base. Be sure to attach the
supporting post in the direction indicated below and
attach the stand to the TV with the wider side of the
base facing forward. 2
Long screws
5 1 Insert the stand cover.
2 Insert the screw to secure the stand cover.
Forward 1
Short screw
1
3 Insert the stand into the openings on the rear of the
TV.
Soft cushion
• To detach the stand, perform the steps in reverse
order.
LC-60LE835U/830U/831U/832U
1 Confirm that there are 10 screws (4 long screws, 4 4 Insert and tighten the 4 screws into the 4 holes on
middle screws and 2 short screws) supplied with the the rear of the stand unit.
stand unit.
Middle screws
2 Attach the supporting post for the stand unit onto
the base as shown below.
• The supporting post attaches to the base at an off-
centered location on the base. Be sure to attach the
supporting post in the direction indicated below and
attach the stand to the TV with the wider side of the
base facing forward.
2
Long screws
5 1 Insert the stand cover.
2 Insert the 2 screws to secure the stand cover.
1
Short screws
Forward 2
3 Insert the stand into the openings on the rear of the 1
TV.
Soft cushion
• To detach the stand, perform the steps in reverse
order.
2–4
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 3. DIMENSIONS
LC-40LE830U
Service Manual
[1] DIMENSIONS (LC-40LE835U/830U/832U)
Unit: inch (mm)
1 3/ 64 (26.4)*2
4 37/ 64 1 5/ 16 (33.4)*3
36 15/ 16 (938) (116) 1 5/ 8 (41)*4
34 7/ 8 (885.6)*1
25 3/ 64 (636)
23 5/ 32 (588)
(498.15)
1411/64 (360)
19 5/ 8*1
10 25/ 64
18 1/ 8 (460)
(264)
1 63/ 64 (50)
4 57/ 64 (124)
11 13/ 16 (300)
19°
20°
(65)
9/ 16
(231)
9 3/ 32
2
11 13/ 16
(300)
12 59/ 64
(328)
4 47/ 64 10 43/ 64
6 55/ 64 (174) (120) (271)
Active area AN-37AG2
*1
*2
Thinnest part
*3
Excluding projecting parts +
*4
Including projecting parts AN-37P30
3–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] DIMENSIONS (LC-46LE835U/830U/832U)
Unit: inch (mm)
1 3/ 64 (26.4)*2
5 11/ 64 1 5/ 16 (33.4)*3
42 13/ 64 (1072) (131) 1 5/ 8 (41)*4
40 3/ 32 (1018.08)*1
26 7/ 64 (663)
28 (711)
15 43/ 64 (398)
(572.67)
22 9/ 16*1
11 35/ 64
19 31/ 32 (507)
(293)
3 5/ 64 (78)
15 3/ 4 (400)
7 7/ 8 (200)
20°
(19)
10 5/ 16
(262)
15 3/ 4 (400)
3/ 4
(365)
3/ 8
14
3 63/ 64 11 55/ 64
8 15/ 32 (215) (101) (301)
*1
Active area
*2
Thinnest part
*3
Excluding projecting parts
*4
Including projecting parts AN-52AG4
3–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[3] DIMENSIONS (LC-52LE835U/830U/832U)
Unit: inch (mm)
1 3/ 64 (26.4)*2
5 11/ 64 1 5/ 16 (33.4)*3
47 31/ 64 (1206) (131) 1 5/ 8 (41)*4
45 23/ 64 (1152.0)*1
30 63/ 64 (787)
29 1/ 16 (738)
25 33/ 64*1
(648.0)
17 11/ 64
(436)
11 35/ 64
4 19/ 64 (109)
19 31/ 32 (507) (293)
15 3/ 4 (400)
7 3/ 32 (180)
20°
47/ 64
(19)
(298)
15 3/ 4 (400)
11
3/ 4
15 3/ 4 (400)
3 63/ 64 12 9/ 32
8 15/ 32 (215) (101) (312)
*1
Active area
*2
Thinnest part AN-52AG4
*3
Excluding projecting parts
*4
Including projecting parts
3–3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[4] DIMENSIONS (LC-60LE835U/830U/831U/832U)
Unit: inch (mm)
1 3/ 64 (26.4)*2
6 5/ 16 1 5/ 16 (33.4)*3
54 29/ 64 (1383) (160) 1 5/ 8 (41)*4
52 11/ 32 (1329.12)*1
34 31/ 32 (888)
33 1/ 32 (839)
(747.63)
19 9/ 64 (486)
29 7/ 16*1
5 23/ 32 (145)
21 7/ 64 (536) 14 27/ 64 (366)
15 3/ 4 (400) 10°
9 1/ 16 (230)
17 31/ 64 (444) 15 3/ 32 (383)
2 1/ 16 (52)
(400)
3/ 4
15
3 63/ 64 8 13/ 64
8 15/ 32 (215) (101) (208)
*1
Active area AN-52AG4
*2
Thinnest part
*3
Excluding projecting parts
*4
Including projecting parts
3–4
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 4. REMOVING OF MAJOR PARTS
LC-40LE830U
Service Manual
[1] REMOVING OF MAJOR PARTS (LC-40LE835U/830U/832U)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 1 lock screw and detach the Stand Support Cover .
2. Remove the 3 lock screws and detach the Stand Unit .
3. Remove the 1 lock screw and detach the AC Cord Cover .
4. Disconnect AC Cord .
5. Remove the 4 Vesa Hole Covers , 5 lock screws and 14 lock screws and detach the Rear Cabinet Ass’y .
11 Rear Cabinet Ass'y
AC Cord 7 10
AC Cord Cover 6
5
9
8
3
Stand Support Cover 2
10
Stand Unit 4
4–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
2. Removing of Speaker-L/R.
1. Remove the 8 lock screws and detach the Fixing Metal Angle .
2. Detach the Bottom Cover .
3. Disconnect SP wire.
4. Detach the Speaker-L , Speaker-R .
MAIN Unit
[SP]
3 Bottom Cover
2 Fixing Metal
Angle
1
[SP]
Speaker-R 5 Speaker-L 4
4–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
3. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, PD, LW (LC-40LE835U), PL, RC, Cl, UB, LV (LC-40LE830U/832U))
2. Disconnect the following connectors from the POWER/LED Drive Unit. (PD, L1)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED Drive Unit MAIN Unit
[PD]
[L1]
[PL]
[LW]
LCD Control Unit
MAIN Unit
[SB] [PD]
LC-40LE830U/832U
[LV]
[LW]
[PL]
LC-40LE835U [RC]
[CI]
[UB]
4–3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
4. Removing of MAIN Unit, POWER/LED Drive Unit, Speaker (Sub Woofer), 40” LCD Panel Module Unit.
1. Remove the 5 lock screws and detach the Main PWB Shield and Terminal Angle Bottom .
2. Remove the 3 lock screws and detach the MAIN Unit .
3. Remove the 6 lock screws and detach the POWER/LED Drive Unit and Insulator Sheet .
4. Detach the Speaker (Sub Woofer) .
5. Remove the 9 lock screws and detach the Center Angle-L , Center Angle-R .
6. Detach the 8 Fixing Metal Angles .
7. Remove the 7 Hooks and detach the 40” LCD Panel Module Unit .
1
5
Main
PWB Shield 2
6 POWER/LED
Drive Unit
[SB]
Speaker 8
(Sub Woofer) 15
4 MAIN Unit
Insulator
7 Sheet
3 Terminal Angle
Fixing Metal Bottom
12 Angle
Fixing Metal Angle 12
12 Fixing Metal Angle
Fixing Metal Angle 12 12 Fixing Metal Angle
13 Hook Hook 13
14 40" LCD Panel
Module Unit
Fixing Metal Angle 12 12 Fixing Metal Angle
13 Hook 13 Hook 13 Hook
9 9
10 Center
Angle-L
11 Center
Angle-R
4–4
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
5. Removing of WiFi Unit, R/C, Operation Unit, ICON Unit, IR Emitter Unit (LC-40LE835U Only), Touch Sensor
Unit.
1. Detach the WiFi Unit .
2. Remove the 1 lock screw and detach the ICON Unit .
3. Detach the R/C, Operation Unit .
4. Detach the IR Emitter Unit (LC-40LE835U Only).
5. Detach the Touch Sensor Unit .
NOTE: The Touch Sensor unit reuse will be impossible, once it is stuck on front cabinet and exfoliates.
Front Cabinet Ass'y
6 Touch Sensor Unit
[TK] [RA]
[RA] [CI] [UB]
ICON 3
[IR] Unit
5 IR Emitter 4 R/C, 1 WiFi
Unit Operation 2 Unit
(LC-40LE835U Only) Unit
4–5
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] REMOVING OF MAJOR PARTS (LC-46LE835U/830U/832U)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 1 lock screw and detach the Stand Support Cover .
2. Remove the 4 lock screws and detach the Stand Unit .
3. Remove the 1 lock screw and detach the AC Cord Cover .
4. Disconnect AC Cord .
5. Remove the 4 Vesa Hole Covers , 5 lock screws and 14 lock screws and detach the Rear Cabinet Ass’y .
7 AC Cord
11 Rear Cabinet Ass'y
10
AC Cord Cover 6 9
3
1 10
Stand Support Cover 2
Stand Unit 4
4–6
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
2. Removing of Speaker-L/R.
1. Remove the 8 lock screws and detach the Fixing Metal Angle .
2. Detach the Bottom Cover .
3. Disconnect SP wire.
4. Detach the Speaker-L , Speaker-R .
MAIN Unit
[SP]
3 Bottom Cover
2 Fixing Metal Angle
1
[SP]
Speaker-R 5 Speaker-L 4
4–7
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
3. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, PD, LW (LC-46LE835U), PL, RC, Cl, UB, LV (LC-46LE830U/832U))
2. Disconnect the following connectors from the POWER/LED Drive Unit. (PD, LA)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED Drive Unit MAIN Unit
[PD]
[LA]
[PL]
[LW]
LCD Control Unit
MAIN Unit
[SB] [PD]
LC-46LE830U/832U
[LV]
[LW]
LC-46LE835U [PL]
[RC]
[CI]
[UB]
4–8
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
4. Removing of MAIN Unit, POWER/LED Drive Unit, Speaker (Sub Woofer), 46” LCD Panel Module Unit.
1. Remove the 5 lock screws and detach the Main PWB Shield and Terminal Angle Bottom .
2. Remove the 3 lock screws and detach the MAIN Unit .
3. Remove the 6 lock screws and detach the POWER/LED Drive Unit and Insulator Sheet .
4. Detach the Speaker (Sub Woofer) .
5. Remove the 12 lock screws and detach the Center Angle-L , Center Angle-R .
6. Detach the 9 Fixing Metal Angles .
7. Remove the 9 Hooks and detach the 46” LCD Panel Module Unit .
1
5
Main
PWB Shield 2
POWER/LED
6 Drive Unit
[SB]
Speaker 8 15
(Sub Woofer)
4 MAIN Unit
7 Insulator Sheet
3 Terminal
Angle Bottom
12 Fixing Metal Angle
Fixing Metal Angle 12
12 Fixing Metal Angle
Fixing Metal Angle 12 12 Fixing Metal Angle
13 Hook 13 Hook
14 46" LCD Panel
Module Unit
Fixing Metal Angle 12 12 Fixing Metal Angle
13 Hook 13 Hook 13 Hook
9 9
11 Center 10 Center
Angle-R Angle-L
4–9
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
5. Removing of WiFi Unit, R/C, Operation Unit, ICON Unit, IR Emitter Unit (LC-46LE835U Only), Touch Sensor
Unit.
1. Detach the WiFi Unit .
2. Remove the 1 lock screw and detach the ICON Unit .
3. Detach the R/C, Operation Unit .
4. Detach the IR Emitter Unit (LC-46LE835U Only).
5. Detach the Touch Sensor Unit .
NOTE: The Touch Sensor unit reuse will be impossible, once it is stuck on front cabinet and exfoliates.
Front Cabinet Ass'y
6 Touch Sensor Unit
[TK] [RA]
[RA] [CI] [UB]
ICON 3
Unit
[IR]
4 R/C, 1 WiFi
5 IR Emitter Operation 2 Unit
Unit Unit
(LC-46LE835U Only)
4 – 10
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[3] REMOVING OF MAJOR PARTS (LC-52LE835U/830U/832U)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 1 lock screw and detach the Stand Support Cover .
2. Remove the 4 lock screws and detach the Stand Unit .
3. Remove the 1 lock screw and detach the AC Cord Cover .
4. Disconnect AC Cord .
5. Remove the 4 Vesa Hole Covers , 7 lock screws and 18 lock screws and detach the Rear Cabinet Ass’y .
7 AC Cord 11 Rear Cabinet Ass'y
10
AC Cord Cover 6
8
5
3
Stand Support Cover 2 10
9
1 10
Stand Unit 4
4 – 11
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
2. Removing of Speaker-L/R.
1. Remove the 8 lock screws and detach the Fixing Metal Angle .
2. Detach the Bottom Cover .
3. Disconnect SP wire.
4. Detach the Speaker-L , Speaker-R .
MAIN Unit
[SP]
3 Bottom Cover
2 Fixing Metal Angle
1
[SP]
Speaker-R 5 Speaker-L 4
4 – 12
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
3. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, PD, LW (LC-52LE835U), PL, RC, Cl, UB, LV (LC-52LE830U/832U))
2. Disconnect the following connectors from the POWER/LED Drive Unit. (PD, LA)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED Drive Unit MAIN Unit
[LA] [PD]
[PL]
[LW]
LCD Control Unit
MAIN Unit
[SB] [PD]
LC-52LE830U/832U
[LV]
[LW]
[PL]
LC-52LE835U [RC]
[CI]
[UB]
4 – 13
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
4. Removing of MAIN Unit, POWER/LED Drive Unit, Speaker (Sub Woofer), 52” LCD Panel Module Unit.
1. Remove the 5 lock screws and detach the Main PWB Shield and Terminal Angle Bottom .
2. Remove the 3 lock screws and detach the MAIN Unit .
3. Remove the 6 lock screws and detach the POWER/LED Drive Unit and Insulator Sheet .
4. Detach the Speaker (Sub Woofer) .
5. Remove the 12 lock screws and detach the Center Angle-L , Center Angle-R .
6. Detach the 12 Fixing Metal Angles .
7. Remove the 11 Hooks and detach the 52” LCD Panel Module Unit .
1
5
Main
PWB Shield 2
POWER/LED
6 Drive Unit
Speaker
(Sub Woofer) [SB]
15
8
4 MAIN Unit
7 Insulator Sheet
Terminal Angle
3
Bottom
Fixing Metal
Fixing Metal 12 12 Angle 12 Fixing Metal Angle
Angle
Fixing
Fixing Metal 12 12 Metal Angle
Angle
14 52" LCD Panel
Module Unit
13 Hook 13 Hook
Fixing Metal 12 Fixing
Angle 12 Metal Angle
Fixing
Fixing Metal 12 12
Metal Angle
Angle
13 Hook 13 Hook 13 Hook
9 9
11 Center 10 Center
Angle-R Angle-L
4 – 14
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
5. Removing of WiFi Unit, R/C, Operation Unit, ICON Unit, IR Emitter Unit (LC-52LE835U Only), Touch Sensor
Unit.
1. Detach the WiFi Unit .
2. Remove the 1 lock screw and detach the ICON Unit .
3. Detach the R/C, Operation Unit .
4. Detach the IR Emitter Unit (LC-52LE835U Only).
5. Detach the Touch Sensor Unit .
NOTE: The Touch Sensor unit reuse will be impossible, once it is stuck on front cabinet and exfoliates.
Front Cabinet Ass'y
6 Touch Sensor Unit
[TK] [RA]
[RA] [CI] [UB]
ICON 3
[IR] Unit
5 IR Emitter 4 R/C, 1 WiFi
Unit Operation 2 Unit
(LC-52LE835U Only) Unit
4 – 15
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[4] REMOVING OF MAJOR PARTS (LC-60LE835U/830U/831U/832U)
1. Removing of Stand Unit and Rear Cabinet Ass’y.
1. Remove the 2 lock screws and detach the Stand Support Cover .
2. Remove the 4 lock screws and detach the Stand Unit .
3. Remove the 1 lock screw and detach the AC Cord Cover .
4. Disconnect AC Cord .
5. Remove the 4 Vesa Hole Covers , 5 lock screws and 23 lock screws and detach the Rear Cabinet Ass’y .
7 AC Cord 11 Rear Cabinet Ass'y
10
8
9
AC Cord Cover 6
10 3
5
Stand Support Cover 2
10
Stand Unit 4
4 – 16
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
2. Removing of Speaker-L/R.
1. Remove the 2 lock screws detach the Bottom Cover .
2. Remove the 19 lock screws and detach the Fixing Metal Angle .
3. Disconnect SP wire.
4. Detach the Speaker-L , Speaker-R .
MAIN Unit
[SP]
Fixing Metal Angle 4
2 Bottom Cover
[SP]
1
Speaker-R 6 Speaker-L 5
4 – 17
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
3. Removing of Connectors
1. Disconnect the following connectors from the MAIN Unit. (SB, PD, LW (LC-60LE835U), PL, RC, Cl, UB, LV (LC-60LE830U/831U/832U))
2. Disconnect the following connectors from the POWER/LED Drive Unit. (PD, LA)
3. Disconnect the following connectors from the LCD Control Unit. (LW, PL)
POWER/LED Drive Unit MAIN Unit
[LA] [PD]
[PL]
[LW]
LCD Control Unit
MAIN Unit
LC-60LE830U/ [SB] [PD]
831U/832U
[LV]
[LW]
[PL]
LC-60LE835U [RC]
[CI]
[UB]
4 – 18
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
4. Removing of MAIN Unit, POWER/LED Drive Unit, speaker (Sub Woofer), 60” LCD Panel Module Unit.
1. Remove the 5 lock screws and detach the Main PWB Shield Terminal Angle Bottom .
2. Remove the 3 lock screws and detach the MAIN Unit .
3. Remove the 6 lock screws and detach the POWER/LED Drive Unit and Insulator Sheet .
4. Detach the Speaker (Sub Woofer) .
5. Remove the 16 lock screws and detach the Center Angle-L , Center Angle-R .
6. Detach the 14 Fixing Metal Angles .
7. Remove the 8 Hooks and detach the 60” LCD Panel Module Unit .
1
POWER/LED
6 Drive Unit
Main PWB Shield 2
7 Insulator Sheet
[SB] 15
Speaker MAIN Unit 4
8
(Sub Woofer) Terminal 3
Angle Bottom
Fixing Metal 12 12 Fixing 12 Fixing
Angle Metal Angle Metal Angle
Fixing Metal
12 12 Fixing
Angle Metal Angle
14 60" LCD Panel
Module Unit
Fixing Metal 12 12 Fixing
Angle Metal Angle
13 Hook 13 Hook 13 Hook 13 Hook
9 9
11 Center 10 Center
Angle-R Angle-L
4 – 19
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
5. Removing of WiFi Unit, R/C, Operation Unit, ICON Unit, IR Emitter Unit (LC-60LE835U Only), Touch Sensor
Unit.
1. Detach the WiFi Unit .
2. Remove the 1 lock screw and detach the ICON Unit .
3. Detach the R/C, Operation Unit .
4. Detach the IR Emitter Unit (LC-60LE835U Only).
5. Detach the Touch Sensor Unit .
NOTE: The Touch Sensor unit reuse will be impossible, once it is stuck on front cabinet and exfoliates.
Front Cabinet Ass'y
6 Touch Sensor Unit
[TK] [RA]
[RA] ICON 3 [CI] [UB]
Unit
[IR]
4 R/C, 1 WiFi
5 IR Emitter Operation 2 Unit
Unit Unit
(LC-60LE835U Only)
4 – 20
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[5] The location putting on the heat measure sheet
1. MAIN PWB Unit
Main PWB Unit
(DUNTKF733WE**)
PSPAZC702WJKZ
The object to cool.
(The sheet is put on the back of the
board.)
The guide line is impressed on the backlight
chassis
4 – 21
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
2. LCD Control Unit
For LC-40/46/52/60LE835U
The IC to cool
LCD control unit
(RUNTK4909TP**)
Please put [PSPAZC062WJKZ] on the IC
4 – 22
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
For LC-40/46/52/60LE830U/832U/LC-60LE831U
The IC to cool
LCD control unit
(RUNTK4910TP**)
Please put [PSPAZC0062WJKZ] on the IC
4 – 23
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[6] Precautions for assembly
1. Attaching the touch sensor
1. After removing the release paper, attach the touch sensor keeping out dust and dirt.
2. Press the 3 circular silk positions on the PWB to fix the touch sensor. There is no problem if the pressing positions are slightly misaligned. How-
ever, do not press the connectors directly since they are very easy to break.
2. Points to be checked and precautions when servicing the unit
Mount the main PWB Ass’y on the backlight chassis and check that the EMI-prevention parts are not peeled and twisted from the access holes. (The
EMI-prevention parts, conductive nonwoven fabric gaskets, must be seen from the access holes.)
[Countermeasure]
Attach the conductive nonwoven fabric gaskets on the shielded case on the main PWB.
PSPAZC691WJZZ x 2 pcs
PSPAZC690WJZZ
Attach the conductive nonwoven fabric gasket on the RF terminal angle.
(PSPAZC691WJZZ)
4 – 24
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
State where the main PWB and shielded case are assembled
Access hole
Access hole
The following is a drawing mounting the main PWB Ass’y on the backlight chassis. (The parts indicated by -> are the access holes for confirmation.)
(Main PWB Ass’y => State where the shielded case and RF terminal angle are mounted on the main PWB)
4 – 25
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[7] The way of detaching Rear Cabinet
• Here are the way of detaching Rear Cabinet. Please respond in following order.
1. Lay the TV set down on the desk or table with the glass side down, set the left hand between Front Cabinet and Rear Cabinet on the bottom of
right corner side.
2. Set the right hand between Front Cabinet and Rear Cabinet on the right side in the under corner.
4 – 26
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
3. Push Rear Cabinet toward the center of TV set with right hand. At the same time, open Rear Cabinet in the back side with left hand and detach the
hook.
Figure for image
Right Hand
Left Hand
4. Detach the hooks one by one in a counterclockwise direction with changing the position of right hand.
Follow the arrows for removing
Start Position
4 – 27
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 5. ADJUSTMENT
LC-40LE830U
Service Manual
[1] ADJUSTMENT PROCEDURE
The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment is
required due to part replacement, make an adjustment according to the following procedure.
1. After replacement of any PWB unit and/or IC for repair, please note the following.
• When replacing the following units, make sure to prepare the new units loaded with updated software.
MAIN Unit: DKEYMF733FM16: LC-40LE835U
DKEYMF733FM14: LC-46LE835U
DKEYMF733FM13: LC-52LE835U
DKEYMF733FM12: LC-60LE835U
DKEYMF733FM04: LC-40LE830U
DKEYMF733FM03: LC-46LE830U
DKEYMF733FM02: LC-52LE830U
DKEYMF733FM01: LC-60LE830U
DKEYMF733FM18: LC-60LE831U
DKEYMF733FM10: LC-40LE832U
DKEYMF733FM08: LC-46LE832U
DKEYMF733FM07: LC-52LE832U
DKEYMF733FM06: LC-60LE832U
• When replacing the LCD control PWB, perform the VCOM adjustment.
2. Upgrading of each microprocessor software
CAUTION: Never “POWER OFF” the unit when software upgrade is ongoing.
Otherwise the system may be damaged beyond recovery.
2.1. Software version upgrade
The model employs the following software.
• Main software LC-40/46/52/60LE835U (please use a software version after BSMK_LE835_xxx.USB).
• Main software LC-40/46/52/60LE830U/832U/LC-60LE831U (please use a software version after BSMK_LE830_xxx.USB).
• Monitor microprocessor software (please use a software version after BSMK_LE835_xxx.USB (for LE835U) or BSMK_LE830_xxx.USB (for
LE830U/LE831U/LE832U) and BSMKMxxx.SMB.)
The main software, monitor microprocessor software can be upgraded by using a general-purpose USB Memory.
The followings are the procedures for upgrading, explained separately for the main software, monitor microprocessor software.
2.2. Main software version upgrade
2.2.1 Get ready before you start
• USB Memory of 128MB or higher capacity.
• PC running on Windows 98/98SE/ME/2000/XP operating system.
• USB Memory reader/writer or PC with a USB port.
• The file system of a USB memory is FAT. (FAT32 supports)
• Use the USB memory without other functions. (lock and memory reader...etc)
2.2.2 Preparations
To upgrade the main software, it is necessary to get ready the USB Memory for version upgrade before you start.
Follow the steps below and create the USB Memory for version upgrade.
1. Copy the file BSMK_LE835_xxx.USB (for LE835U) or BSMK_LE830_xxx.USB (for LE830U/LE831U/LE832U) for version upgrade to the root
directory (folder) of the USB Memory.
NOTE: In the USB Memory drive, do not store other folders or unrelated files, or more than one file for version upgrade.
Now the USB Memory for version upgrade is ready.
5–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
2.2.3 How to upgrade the software
1. Plug AC cord and turn on the TV.
2. After picture displayed, touch the power key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching it.
3. When the center icon LED blinks, release your finger from the power key.
4. Next, touch the “POWER” and “CH ( )” keys at the same time.
5. When the center icon LED turns on, release your finger from the keys.
6. After the unit startup, the system upgrade screen as shown below within 20-40 seconds.
Software Update
52LE835U
MAIN 50%
SUB MICOM NO DATA
PANEL EEPROM NO DATA
3D IR MICOM OK
3D Model:
MAIN Version U1007071
LC-40/46/52/60LE835U Only
SUB MICOM Version 㧙㧙㧙㧙㧙
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version 1.00
7. Even a single failure in the process will trigger the upgrade failure screen.
Software Update
52LE835U
UPGRADE FAILURE
MAIN Project ID
SUB MICOM NO DATA
PANEL EEPROM NO DATA
3D IR MICOM OK
3D Model:
MAIN Version 㧙㧙㧙㧙㧙
LC-40/46/52/60LE835U Only
SUB MICOM Version 㧙㧙㧙㧙㧙
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version 1.00
NOTE: In the event of a failure, repeat the upgrade process. If the process repeatedly fails, it is likely that the hardware need fixing.
8. Upon completion of the whole process, the upgrade success screen as shown below appears. You can check the new software version on this
screen. The version information appears after the upgrade is complete.
Software Update
52LE835U
UPGRADE SUCCESS
MAIN 100%
SUB MICOM NO DATA
PANEL EEPROM NO DATA
3D IR MICOM OK
3D Model:
LC-40/46/52/60LE835U Only MAIN Version U1007071
SUB MICOM Version 㧙㧙㧙㧙㧙
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version 1.00
9. Unplug the AC cord and remove the USB Memory for version upgrade.
10.Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the main
software version information.
5–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
2.3. Monitor microprocessor software version upgrade
Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version
upgrade”.
Copy the file BSMK_LE835_xxx.USB (for LE835U) or BSMK_LE830_xxx.USB (for LE830U/LE831U/LE832U) and BSMKMxxx.SMB. (named tempo-
rarily) for monitor microprocessor software version upgrade to the USB memory.
2.3.1 How to upgrade the software
1. Plug AC cord and turn on the TV.
2. After picture displayed, touch the power key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching it.
3. When the center icon LED blinks, release your finger from the power key.
4. Next, touch the “POWER” key with the “CH ( )” key touching.
5. When the center icon LED turns on, release your finger from the keys.
CAUTION: • The moment this operation is done, the upgrading of the monitor microprocessor software starts. While the upgrade is ongoing, never
power off the unit. Otherwise the upgrade will fail and the system may be serious damaged beyond recovery (inability to start).
• After the monitor microprocessor software is upgraded, also perform the 'Industry Init'.
6. After the unit startup, the upgrade starts. The power led will blink continuously. Also, an upgrade screen will be shown during a minor upgrade.
Software Update
52LE835U
MAIN NO DATA
SUB MICOM 50%
PANEL EEPROM NO DATA
3D IR MICOM OK
3D Model:
MAIN Version 㧙㧙㧙㧙㧙
LC-40/46/52/60LE835U Only
SUB MICOM Version 0.820
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version 1.00
7. If the upgrade fails, power led will stop blinking. Also, the upgrade failure screen will be shown if upgrade screen was shown at 5.
Software Update
52LE835U
UPGRADE FAILURE
MAIN NO DATA
SUB MICOM SAME VERSION
PANEL EEPROM NO DATA
3D IR MICOM OK
3D Model:
MAIN Version 㧙㧙㧙㧙㧙
LC-40/46/52/60LE835U Only
SUB MICOM Version 㧙㧙㧙㧙㧙
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version 1.00
NOTE: In the event of a transient failure, upgrade will be automatically retried up to three times. If the process repeatedly fails, hardware may be the
cause.
8. The upgrade success screen will be shown if upgrade screen was shown at 5.
Software Update
52LE835U
UPGRADE SUCCESS
MAIN NO DATA
SUB MICOM 100%
PANEL EEPROM NO DATA
3D IR MICOM OK
3D Model: MAIN Version 㧙㧙㧙㧙㧙
LC-40/46/52/60LE835U Only
SUB MICOM Version 0.820
PANEL EEPROM 㧙㧙㧙㧙
3D IR MICOM Version 1.00
9. Unplug the AC cord and remove the USB Memory for version upgrade.
10.Now the software version upgrade is complete.
NOTE: When you are done with the software version upgrade, start the set, go to the top page of the adjustment process screen and check the mon-
itor microprocessor software version information and panel size information.
5–3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
3. Entering and exiting the adjustment process mode
1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu.
2) At the state TV is turned on, touch the power key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching the power key.
3) When the center icon LED blinks, release your finger from the power key.
4) Next, touch the “POWER” key with the “VOL (—)” and “INPUT” key touching.
TV will turn on and the letter “<K>” appears on the screen.
5) Next, touch the “VOL (—)” and “CH ( )” keys at the same time.
6) When the center icon LED turns on, release your finger from the keys.
(The “VOL (—)” and “CH ( )” keys should be pressed and held until the display appears.)
Multiple lines of blue characters appearing on the display indicate that the unit is now in the adjustment process mode.
When you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
7) To exit the adjustment process mode after the adjustment is done, unplug the AC cord from the outlet to make a forced shutdown. (When the
power was turned off with the remote controller, once unplug the AC cord and plug it again. In this case, wait 10 seconds or so before plugging.)
CAUTION: Use due care in handling the information described here lest your users should know how to enter the adjustment process mode. If the
settings are tampered in this mode, unrecoverable system damage may result.
4. Remote controller key operation and description of display in adjustment process mode
1) Key operation
Remote controller key Main unit key Function
CH ( / ) CH ( / ) Moving an item (line) by one (UP/DOWN)
VOL (+/–) VOL (+/–) Changing a selected item setting (+1/ –1)
Cursor (UP/DOWN) ————— Turing a page (PREVIOUS/NEXT)
Cursor (LEFT/RIGHT) ————— Changing a selected line setting (+10/ –10)
INPUT ————— Input switching (toggle switching)
ENTER ————— Executing a function
*Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
2) Description of display
(2) Current selected input
(1) Current page/ (3) Current color system
(5) LCD Panel size/Speaker type
Total pages (4) Destination
1/27 INPUT4 AUTO USA 60_UNDER (6) Adjustment
process menu
MAIN Version 1.04 (U 2010/07/07 1 A) header
BOOT Version BSMKxxx
Monitor / Monitor BOOTVersion 1.02 / 1.00
T-CON Version / LED CON Version 201006162D60250101 / FC
NETFLIX ESN ERR
WIDEVINE DEVICE ID 100531010000003D
(7) Parameters
FRC Version 201006162D60250101 / 010000000000000048
TOUCH SENSOR/IR Micom Version B0079022310 / 1.00
TEMPERATURE 73
LAMP ERROR 0
MONITOR ERR CAUSE 1) 11 B00000041:17 2) 11 B00000041:13
3) 11 B00000040:36 4) 11 B00000040:35
NORMAL STANDBY CAUSE 0
ERROR STANDBY CAUSE 0 0 0 0 0
5–4
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
5. List of adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page Line Item Description Remarks (adjustment detail, etc.)
1 1 MAIN Version Main software version
2 BOOT Version
3 Monitor / Monitor BOOT Version Monitor and monitor boot software version
4 T-CON Version / LED CON Version LCD controller software version
5 NETFLIX ESN
6 WIDEVINE DEVICE ID
7 FRC Version
8 TOUCH SENSOR/IR Micom Version
9 TEMPERATURE Panel temperature
10 LAMP ERROR Number of termination due to lamp error
11 MONITOR ERR CAUSE
12 NORMAL STANDBY CAUSE Refer to *1 under the list for details
13 ERROR STANDBY CAUSE Refer to *2 under the list for details
2 1 INDUSTRY INIT Initialization to factory settings
2 INDUSTRY INIT(-Public)
3 PUBLIC MODE Public mode
4 Center Acutime Accumulated main operation time
5 RESET Reset
6 Backlight Acutime Accumulated monitor operation time
7 RESET Reset
8 LAMP ERROR RESET Reset LAMP ERROR
9 VIC XPOS X-coordinate setting for VIC READ
10 VIC YPOS Y-coordinate setting for VIC READ
11 VIC COLOR Collected color data setting for VIC READ
12 VIC SIGNAL TYPE Signal type setting for VIC READ
13 VIC READ Picture level acquisition function Level appears in green on the upper right
3 1 N358 MAIN ADJ(INPUT2) CVBS and TUNER signal level adjustment
2 N358 MAIN ADJ(INPUT2) CVBS signal level adjustment
3 TUNER DAC ADJ TUNER signal level adjustment
4 N358 CONTRAST A_GAIN
5 N358 CONTRAST D_GAIN
6 N358 CONTRAST OFFSET
7 TUNER CONTRAST A_GAIN
8 TUNER CONTRAST D_GAIN
9 TUNER CONTRAST OFFSET
4 1 TUNER VCHIP TEST(69ch) Tuning test and VCHIP test (69ch)
2 TUNER VCHIP TEST(7ch) Tuning test and VCHIP test (7ch)
3 TUNER VCHIP TEST(10ch) Tuning test and VCHIP test (10ch)
4 TUNER VCHIP TEST(15ch) Tuning test and VCHIP test (15ch)
5 INSPECT USB TERM
6 HDMI EDID WRITE
7 HDMI CEC TEST
5 1 COMP15K ADJ(INPUT1) Component 15K picture level adjustment (main)
2 COMP15K Y A_GAIN
3 COMP15K Cb A_GAIN
4 COMP15K Cr A_GAIN
5 COMP15K Y OFFSET
6 COMP15K Cb OFFSET
7 COMP15K Cr OFFSET
6 1 COMP33K ADJ(INPUT1) Component 33K picture level adjustment (main)
2 COMP33K Y A_GAIN
3 COMP33K Cb A_GAIN
4 COMP33K Cr A_GAIN
5 COMP33K Y OFFSET
6 COMP33K Cb OFFSET
7 COMP33K Cr OFFSET
5–5
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
Page Line Item Description Remarks (adjustment detail, etc.)
7 1 ANALOG RGB ADJ Analog RGB picture level adjustment
2 R A_GAIN
3 G A_GAIN
4 B A_GAIN
5 R OFFSET
6 G OFFSET
7 B OFFSET
8 1 VCOM ADJ VCOM adjustment value
9 1 LEV1 Standard value 1 Adjustment gradation setting.
2 LEV2 Standard value 2
3 LEV3 Standard value 3
4 LEV4 Standard value 4
5 LEV5 Standard value 5
6 LEV6 Standard value 6
10 1 MG1R WB adjustment Point 1, R adjustment value Parameter for six-point adjustment
2 MG1G WB adjustment Point 1, G adjustment value
3 MG1B WB adjustment Point 1, B adjustment value
4 MG1Y WB adjustment Point 1, Y adjustment value
5 MG2R WB adjustment Point 2, R adjustment value
6 MG2G WB adjustment Point 2, G adjustment value
7 MG2B WB adjustment Point 2, B adjustment value
8 MG2Y WB adjustment Point 2, Y adjustment value
9 MG3R WB adjustment Point 3, R adjustment value
10 MG3G WB adjustment Point 3, G adjustment value
11 MG3B WB adjustment Point 3, B adjustment value
12 MG3Y WB adjustment Point 3, Y adjustment value
11 1 MG4R WB adjustment Point 4, R adjustment value Parameter for six-point adjustment
2 MG4G WB adjustment Point 4, G adjustment value
3 MG4B WB adjustment Point 4, B adjustment value
4 MG4Y WB adjustment Point 4, Y adjustment value
5 MG5R WB adjustment Point 5, R adjustment value
6 MG5G WB adjustment Point 5, G adjustment value
7 MG5B WB adjustment Point 5, B adjustment value
8 MG5Y WB adjustment Point 5, Y adjustment value
9 MG6R WB adjustment Point 6, R adjustment value
10 MG6G WB adjustment Point 6, G adjustment value
11 MG6B WB adjustment Point 6, B adjustment value
12 MG6Y WB adjustment Point 6, Y adjustment value
13 MG6Y OFFSET
12 1 MODE SELECT
2 POS SELECT
3 POS MIN
4 POS MID1
5 POS MID2
6 POS MID3
7 POS MID4
8 POS MID5
9 POS MID6
10 POS MAX
13 1 CD MIN
2 CD MID1
3 CD MID2
4 CD MID3
5 CD MID4
6 CD MID5
7 CD MID6
8 CD MAX
5–6
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
Page Line Item Description Remarks (adjustment detail, etc.)
14 1 CALC
2 RESET
3 VAL1
4 VAL2
5 VAL3
6 VAL4
7 VAL5
8 VAL6
15 1 MONITOR TIME OUT
2 MONITOR MAX TEMP
3 MONITOR ERROR CAUSE RESET
16 1 LCD TEST PATTERN
2 LCD TEST PATTERN1
3 LCD TEST PATTERN2
4 LCD TEST PATTERN3
5 LCD TEST PATTERN4
6 TV TEST PATTERN 1
7 TV TEST PATTERN 2
17 1 T-CON VERSION EXT.1 PRIMROSE 2D Version
2 T-CON VERSION EXT.2 PRIMROSE 3D Version
3 T-CON VERSION EXT.3 Blank (Not Use)
4 T-CON VERSION EXT.4 Blank (Not Use)
18 1 3D HDMI FPGA Version 3D Model Only (LC-40/46/52/60LE835U)
2 2D->3D FPGA Version 3D Model Only (LC-40/46/52/60LE835U)
3 3D IR EMITTER CONTROL 3D Model Only (LC-40/46/52/60LE835U)
19 1 READ/WRITE
2 SLAVE ADDRESS
3 RESISTER ADDRESS UPPER
4 RESISTER ADDRESS LOWER
5 WRITE DATA UPPER
6 WRITE DATA LOWER
7 READ DATA UPPER
8 READ DATA LOWER
20 1 POWER LED BRIGHTNESS
2 MENU LED BRIGHTNESS
3 INPUT LED BRIGHTNESS
4 CH UP LED BRIGHTNESS
5 CH DOWN LED BRIGHTNESS
6 VOL UP LED BRIGHTNESS
7 VOL DOWN LED BRIGHTNESS
8 LOGO LED BRIGHTNESS
9 ICON LED BRIGHTNESS
10 ICON LED BRIGHTNESS
(STANDBY)
11 3D LED BRIGHTNESS
21 1 POWER KEY SENSITIVITY
2 MENU KEY SENSITIVITY
3 INPUT KEY SENSITIVITY
4 CH UP KEY SENSITIVITY
5 CH DOWN KEY SENSITIVITY
6 VOL UP KEY SENSITIVITY
7 VOL DOWN KEY SENSITIVITY
22 1 KEY STRENGTH GET MODE
2 POWER KEY STRENGTH
3 MENU KEY STRENGTH
4 INPUT KEY STRENGTH
5 CH UP KEY STRENGTH
6 CH DOWN KEY STRENGTH
7 VOL UP KEY STRENGTH
8 VOL DOWN KEY STRENGTH
5–7
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
Page Line Item Description Remarks (adjustment detail, etc.)
23 1 CROSSTALK ADJ MODE
2 CROSSTALK TH1
3 CROSSTALK TH2
4 CROSSTALK TH3
5 CROSSTALK TH4
6 CROSSTALK GAIN1
7 CROSSTALK GAIN2
8 CROSSTALK GAIN3
24 1 WIFI SSID 2.4GHz Set AP SSID
2 WIFI SSID 5GHz Set AP SSID
3 WIFI RSSI 2.4GHz Set RSSI threshold
4 WIFI RSSI 5GHz Set RSSI threshold
5 WIFI TIME 2.4GHz Set Time Out
6 WIFI TIME 5GHz Set Time Out
7 WIFI RSSI TEST Execute test
8 WIFI RSSI RESULT Display test result
25 1 KEY LOCK (1217)
2 KOUTEI AREA ALL CLEAR
3 A MODE AREA CLEAR
4 BACKUP AREA CLEAR
5 B MODE AREA CLEAR
6 EXECUTION
26 1 ERROR STANDBY CAUSE1
2 ERROR STANDBY CAUSE2
3 ERROR STANDBY CAUSE3
4 ERROR STANDBY CAUSE4
5 ERROR STANDBY CAUSE5
6 ERROR STANDBY CAUSE RESET
27 1 EEP SAVE Writing setting values to EEPROM
2 EEP RECOVER Reading setting values from EEPROM
3 MODEL NAME
4 PANEL SIZE
5 SETTING FOR ADJ
6 PANEL LIMIT
7 PANEL RANGE LIMIT
8 SHORT CHECK MODE
9 SHORT CHECK CURRENT
10 CURRENT SW
5–8
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
*1 Details of P1.12 (NORMAL STANDBY CAUSE)
When TV set is powered off due to normal use or product specification, the last cause will be recorded.
The code, character string and description for the standby cause are below.
If you power off by remote, the cause will not be recorded.
Code Character string Description
2 NO_OPERT No operation off
3 NO_SIGNA No signal off
6 SLEEP_TM Off timer
8 OFF_232C Command from RS232C
*2 Details of P1.13 (ERROR STANDBY CAUSE)
When TV set is powered off due to any anomaly detection, the past 5 causes will be recorded.
You can confirm the time those causes occurred and character string in the adjustment process mode menu. (Page 26/27)
The time is accumulated total after TV set is powered on, and the value corresponds to “Center Acutime” in the adjustment process mode menu.
The code, character string and description for the standby cause are below.
If no error has occurred, the code is 0 and the character string is “NO RECORD”.
Code Character string Description
1A E_MONITR Monitor trouble detected
1B E_CVICBT Driver boot error
22 E_TCNERR Software abnormality of LCD controller
48 E_MRESET Failure of resetting menu settings (Initial Setup - Reset)
50 E_TCNF_S T-CON FPGA status error
54 E_TCON_E T-CON hung-up
Monitor ERR STBY table
Outline: Communication/Power failure detected by the monitor microcomputer is stored in EEPROM, and last 4 abnormal can
be confirmed in the Process mode A.
Location: Page 1 of the process mode A: MONITOR ERR CAUSE. “0” if there is no error. It is cleared to 0 on the last page of
the process mode A.
Display Error description
02 Initial communication from the main CPU is not received. Check UART bus between main CPU and sub CPU.
03 Only the initial communication is received.
04 Until panel information request reception
05 Until initialization completion reception
06 Until version notification transmission
07 Until start-up information notification transmission
08 Until start-up information response reception
09 Until time-out setting reception
0A Request time-out
0B Restart time-out during the beginning of time acquisition start-up
0C Ending sequence time-out
0D Preset start-up time-out during completion
0E Download, start-up time-out
0F Time acquisition time-out
11 Regular communication time-out
16 Backlight error See p.6-5
1A Monitor temperature failure - Check TV setting environment
- Check the other monitor (ref No.)
1E DET_13V failure Check 13V power line.
1F DET_D3V3 failure Check D3V3 power line.
20 ERROR_3D (3D-PWB) failure Check 3D-PWB
21 DET_PNLxxV failure Check T-CON power line
23 Error standby request from the main CPU Check ERROR STANDBY CAUSE (p.5-8)
5–9
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
6. Special features
* STANDBY CAUSE (Page 1/27)
Display of a cause (code) of the last standby
The cause of the last standby is recorded in EEPROM whenever possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
* EEP SAVE (Page 27/27)
Storage of EEP adjustment value
* EEP RECOVER (Page 27/27)
Retrieval of EEP adjustment value from storage area
7. Writing the microprocessor software
7.1. Writing the main microprocessor software and monitor microprocessor software
(Main PWB: QPWBXF733WJN1/QPWBXF733WJZZ/QPWBXF733WJN2)
Adjustment item Adjustment conditions Adjustment procedure
1 Writing the main micropro- Checker process 1. Using the checker, connect the specified writing tool to the TL8461 thru
cessor software and moni- TL8475.
tor microprocessor software 2. Using the checker, connect the USB memory to the J9502 (TL9503, TL9506-
<Main PWB> Checking the file version 9508) or J9504 (TL9520-9523)
Checking the USB memory 3. Apply the specified voltage to the PWB and boot it up with the tool connected.
4. Send the software writing start command via RS232C.
5. Send the writing status check command and confirm the response of OK. Then
turn off the power.
CAUTION: When the USB memory is not inserted or reading error occurs, nothing
is written.
8. Signal adjustment
8.1. LCD section adjustment [LCD module adjustment]
Adjustment item Adjustment conditions Adjustment procedure
1 Opposite bias adjustment Adjustment in the center 1. Enter the process mode using the process adjustment remote control.
(LCD module adjustment position of the panel 2. Select [VCOM ADJ (2D)] using the Channel / keys on the remote con-
item) trol.
3. Press the Enter key to check that the pattern for adjustment is displayed.
4. Make adjustment so that the flicker located in the center of the screen is mini-
mized using the Volume +/- keys on the remote control.
5. If the optimum condition is obtained in step 4, press the Enter key to turn off the
pattern.
CAUTION: * Make adjustment with no ANT signal (since the brightness is
changed by the active backlight).
[Adjustment position]
1/2 1/2
1/2
1/2
5 – 10
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
8.2. Image adjustment
8.2.1 Device check
Before adjustment, check that the adjustment jig and signal source are set for Sharp LCD US.
Signal generator level adjustment check (Adjust to the standard value level.)
•Composite signal: 0.714Vp-p ± 0.02Vp-p (Pedestal to white)
•15K component signal: Y level: 0.714Vp-p± 0.02Vp-p (Pedestal to white)
PB/PR level: 0.7Vp-p ± 0.02Vp-p
•33K component signal: Y level: 0.7Vp-p ± 0.02Vp-p (Pedestal to white)
PB/PR level: 0.7Vp-p ± 0.02Vp-p
•Analog RGB: RGB level: 0.7Vp-p ± 0.02Vp-p (Pedestal to white)
8.2.2 Process mode
Adjustment point Adjustment conditions Adjustment procedure
Process mode Enter the process adjustment mode using the process adjustment remote control.
8.2.3 Composite N358 signal/tuner adjustment
Adjustment point Adjustment conditions Adjustment procedure
1 Setting N358 signal •Send the N358 color bar (color saturation: 75%) signal to the composite input.
US-10ch •Send the in-house signal (use US-10ch) to TUNER.
[Video input signal] [In-house US-10ch]
Color saturation: 75%
100% white 0% black 100% white
2 Automatic adjustment exe- Point the cursor to [ N358 ALL ADJ(INPUT2)] and press the [Enter] key.
cution The adjustment is complete when [ N358 ALL ADJ(INPUT2) OK] is displayed.
8.2.4 Component 15K signal adjustment
Adjustment point Adjustment conditions Adjustment procedure
1 Setting 480i signal •Send the 100% color bar signal to the component input.
Color saturation: 100% 480i
100% color bar
100% white 0% black
2 Automatic adjustment exe- Point the cursor to [ COMP15K ADJ(INPUT1)] and press the [Enter] key.
cution The adjustment is complete when [ COMP15K ADJ(INPUT1) OK] is displayed.
5 – 11
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
8.2.5 Component 33K signal adjustment
Adjustment point Adjustment conditions Adjustment procedure
1 Setting 1080i signal •Send the 100% color bar signal to the component input.
Color saturation: 100% 1080i
100% color bar
100% white 0% black
2 Automatic adjustment exe- Point the cursor to [ COMP33K ADJ(INPUT1)] and press the [Enter] key.
cution The adjustment is complete when [ COMP33K ADJ(INPUT1) OK] is displayed.
8.2.6 Analog RGB signal adjustment
Adjustment point Adjustment conditions Adjustment procedure
1 Setting Signal: XGA •Send the 100% color bar signal to the PC input.
(1024x768) 60Hz
SYNC: HV separate
XGA (1024x768)
100% color bar
100% white 0% black
2 Automatic adjustment exe- Point the cursor to [ ANALOG RGB ADJ] and press the [Enter] key.
cution The adjustment is complete when [ ANALOG RGB ADJ OK] is displayed.
8.2.7 Tuner/V-CHIP adjustment
Adjustment point Adjustment conditions Adjustment procedure
1 Setting NTSC RF signal •Send the NTSC signal to the RF antenna input.
US-7(AIR)ch
2 Automatic adjustment exe- Point the cursor to [ VCHIP TEST(*07ch)] and press the [Enter] key. (* Adjust the
cution selected channel to the in-house signal.)
The adjustment is OK when [ VM-OK] is displayed in green.
(NG when VM-NG is displayed in red.)
5 – 12
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
9. White balance adjustment
9.1. White balance adjustment (For details about the adjustment procedure, refer to “Kameyama Model Integrated Monitor
WB Adjustment Specification V1.92”.)
Adjustment
Adjustment conditions Adjustment procedure
point
1 Setting 1) Set the unit to the following conditions.
AV MODE: [DYNAMIC]
Backlight: +16
Active Backlight: OFF
Aging Time: Min. 60 minutes
2) Connect the unit with the white balance adjustment jig.
2 Automatic [Command] [Adjustment procedure]
adjustment exe- Process mode 1) Send the “adjustment process” code using the remote control.
cution KRSW0001 2) Set the point 6 to the specified gradation, specify the strongest color as the fixed
KKT10037 color, and adjust the RGB so that it becomes the standard value through negative
adjustment. Then compare the R and G values; based on the result, calculate the Ye
Setting value in the following conditions.
KY0F0000 R > G: Ye = G x 1.05
0SDS0001 R G: Ye = R x 1.05
SBSL0016 * If the Ye value exceeds the initial value (input gradation x 4), it is rounded to that
value or less.
Multi-point adjustment mode 3) Set the point 5 to the specified gradation, set the G correction value (692 x G value of
MSET0011 point 6/916) (fractions rounded off) and the Ye correction value (692 x Ye value of
point 6/916) (fractions rounded off), and adjust the RB so that it becomes the stan-
Point 6 dard value.
LEV60229 4) Set the point 4 to the specified gradation, set the G correction value (532 x G value of
MG6G**** point 6/916) (fractions rounded off) and the Ye correction value (532 x Ye value of
MG6B**** point 6/916) (fractions rounded off), and adjust the RB so that it becomes the stan-
MG6R**** dard value.
MG6Y**** 5) Set the point 3 to the specified gradation, set the G correction value (464 x G value of
point 6/916) (fractions rounded off) and the Ye correction value (464 x Ye value of
Point 5 point 6/916) (fractions rounded off), and adjust the RB so that it becomes the stan-
LEV50173 dard value.
MG5G**** 6) Set the point 2 to the specified gradation, set the G correction value (296 x G value of
MG5B**** point 6/916) (fractions rounded off) and the Ye correction value (296 x Ye value of
MG5R**** point 6/916) (fractions rounded off), and adjust the RB so that it becomes the stan-
MG5Y**** dard value.
7) Set the point 1 to the specified gradation, set the G correction value (180 x G value of
Point 4 point 6/916) (fractions rounded off) and the Ye correction value (180 x Ye value of
LEV40133 point 6/916) (fractions rounded off), and adjust the RB so that it becomes the stan-
MG4G**** dard value.
MG4B**** 8) Write the adjustment value by the MSET0003 command and turn off the AC power.
MG4R**** * RGB initial value of point 6: Set gradation 916
MG4Y**** * RGB initial value of points 1 to 5: G correction value of each point
(At each point, make adjustment so that the remainder of the RGB adjustment value/
Point 3 4 is equal.)
LEV30116 [Adjustment value]
MG3G**** * According to the “Standard settings” submitted by the Technical Department
MG3B**** [LC52LE835U] LE835 model teaching set
MG3R****
MG3Y****
Point 2
LEV20074
MG2G****
MG2B****
MG2R****
MG2Y****
Point 1
LEV10045
MG1G****
MG1B****
MG1R****
MG1Y****
Writing
MSET0003
5 – 13
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
Adjustment
Adjustment conditions Adjustment procedure
point
[Adjustment standard value]
Measuring instrument: [Minolta CA-210] Technical measuring instrument
Level Reference value Adjustment spec Inspection spec
X=0.272
Point 6 916 ±0.0010 ±0.0020
y=0.277
X=0.272
Point 5 692 ±0.0010 ±0.0020
y=0.277
X=0.272
Point 4 532 ±0.0015 ±0.0030
y=0.277
X=0.272
Point 3 464 ±0.0020 ±0.0040
y=0.277
X=0.272
Point 2 296 ±0.0030 ±0.0060
y=0.277
X=0.272
Point 1 180 ±0.004 ±0.0080
y=0.277
Remarks Setting conditions for inspection
AV MODE: [DYNAMIC] (Reset)
Monochro: ON
Active Backlight: OFF
Aging Time: Min. 60 minutes
10. Key writing
10.1. EDID writing (Main PWB: QPWBXF733WJN1/QPWBXF733WJZZ/QPWBXF733WJN2)
Adjustment point Adjustment conditions Adjustment procedure
1 HDMI EDID writing Process mode 1) Enter the process mode.
(Main PWB) Model discrimination check 2) Point the cursor to [HDMI EDID WRITE] and press the [ENT]
key.
The writing is complete when [OK] is displayed.
(If not written, HDMI does not function.)
CAUTION: Perform the data writing after setting the model discrimi-
nation. The data based on the model discrimination
information is recorded in EEPROM.
10.2. MAC key writing (MAIN PWB: QPWBXF733WJN1/QPWBXF733WJZZ/QPWBXF733WJN2)
1. Write the MAC key data on XXXX mounted on the main PWB.
2. Carry out thorough data management to avoid redundant writing of data.
If the IC where data is written is damaged, replace the PWB since only the IC cannot be changed.
10.3. NETFLIX/WMDRM key writing (MAIN PWB: QPWBXF733WJN1/QPWBXF733WJZZ/QPWBXF733WJN2)
1. Write the NETFLIX/WMDRM key data on XXXX mounted on the main PWB.
2. Carry out thorough data management to avoid redundant writing of data.
If the IC where data is written is damaged, replace the PWB since only the IC cannot be changed.
5 – 14
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
11. Factory setting
After completing the factory setting, pull out the AC cord to complete the setting.
CAUTION: Do not turn on the power after completing the factory setting. If the power is turned on, configure the factory setting again.
Adjustment point Adjustment conditions Adjustment procedure
1 Factory setting Complete the setting by •Point the cursor to [INDUSTRY INIT], set to “ON” using [+]/[-] of the [VOL] key, and press
pulling out the AC cord. the [ENT] key.
The version confirmation screen appears on the green screen. It is completed when [SUC-
CESS] is displayed at the top.
(If error occurs, [ERROR] is displayed on the red screen.)
•Turn off the AC power.
The following items are initialized when configuring the factory setting.
1) User set value
2) Channel data (broadcasting frequency, etc.)
3) Password setting value
4) Operating time
5) StandbyCause
6) Auto installation flag
7) V-CHIP block setting value
12. Software version
1. Main microcomputer
2. Monitor microcomputer
3. EDID data (Analog RGB)
4. (Reference: File name in the Technical Department)
For analog RGB Input3: IC509: edid_dsub15_fullhd_v6_256_fix.BIN
13. An anti-crosstalk measure at the time of the low temperature
• It is a function to control a picture gain depending on the value of the thermistor on the board to reduce crosstalk at the time of the low tempera-
ture.
• The value of the thermistor is confirmed in “TEMPERATURE” of 1/27 pages menus in a process.
• When change the parameter of this function, turn on “CROSSTALK ADJ MODE” of 23/27 pages menus in a process.
• The other parameters of 23/27 pages menus support the following graph in a process.
• For a function to control a picture gain, a screen darkens depending on setting.
• Because the most suitable value is set by default, please do not usually change it.
㪧㫀㪺㫋㫌㫉㪼㩷㪾㪸㫀㫅
CROSSTALK GAIN1
CROSSTALK GAIN2
CROSSTALK GAIN3
CROSSTALK TH4 CROSSTALK TH2 㪧㪸㫅㪼㫃㩷㫊㫌㫉㪽㪸㪺㪼㩷㫋㪼㫄㫇㪼㫉㪸㫋㫌㫉㪼㩷
CROSSTALK TH3 CROSSTALK TH1 (A thermistor value)
5 – 15
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
• There are the following 3 ways to get the public mode setup screen displayed.
In the adjustment process mode, turn on “PUBLIC MODE”
1) Plug AC cord and turn on the TV.
2) After picture displayed, touch the “POWER” key for 5seconds.
NOTE: Picture will disappear when you touch the power key, but keep touching it.
3) When the center icon LED blinks, release your finger from the power key.
4) Next, touch the ”POWER” key with the “CH ( )” key and “VOL (+)” key touching.
5) When the center icon LED turns on, release your finger form the keys.
It’s same as from 1) to 3)
4) Next, touch the “POWER” key with the “INPUT” key and “CH ( )” key touching.
5) When the center icon LED turns on, release your finger form the keys.
6) Get the password input screen displayed.
Procedure
˴The input starts with the leftmost digit.
˴Use the numeric keys [1] thru [9] and [0] keys on the remote controller.
˴The other keys are not acceptable.
˴With a numeric-key input, "_" will change to "˴".
˴The input position will move one digit to the right.
˴With all the 3 digits entered, the password will be verified.
7) The 3-digit password is now verified.
The password [0] [2] [7] provides for the public mode screen. (This screen comes on with whatever adjustment process settings.)
With any other passwords, the screen changes to the normal mode.
2. How to exit Public Mode
There are the following ways to quit the public mode setup screen.
• Turn off “PUBLIC MODE” in the adjustment process mode. ( ) ← This way alone is not for quitting the setup screen, but for quitting the mode itself.
• Turn off the power with the “POWER” key. ( )
• Select “EXECUTE”. ( )
... “PUBLIC MODE” stays on in the adjustment process mode.
... The settings will be back to the factory ones.
3. Public Mode Setting Values
• With the factory settings made, the public mode settings get initialized. (The adjustment process remains intact.)
5 – 16
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
4. Public Mode Menu
The guidance is not displayed on screen.
Setup procedure
• To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH ( )/( )” key (remote controller and set).
• To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set).
• To save new settings, keep the cursor at “EXECUTE” and use “ENTER” key (remote controller and set).
PUBLIC MODE
POWER ON FIXED [VARIABLE ]
MAXIMUM VOLUME [ 60 ]
VOLUME FIXED [VARIABLE ]
VOLUME FIXED LEVEL [ 20 ]
RC BUTTON [RESPOND ]
PANEL BUTTON [RESPOND ]
MENU BUTTON [RESPOND ]
AV POSITION FIXED [VARIABLE ]
ON SCREEN DISPLAY [YES ]
INPUT MODE START [NORMAL ]
INPUT MODE FIXED [VARIABLE ]
LOUD SPEAKER [ON ]
RC_PATH_THROUGH [OFF ]
232C POWON [DISABLE ]
PUBLIC MODE [OFF ]
RESET
EXECUTE
5 – 17
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
5. On Setting Items
* “EZ-SETUP” discussed below indicates “EZ-SETUP after the first power-on”.
1) POWER ON FIXED
Selection Selection between “Variable” and “Fixed” (loop provided)
Default – (Variable)
Explanation In “Fixed” setting, the power-off by the power key of the unit is invalidated and the image is kept being received. The power can
be turned off by stopping the power supply from AC.
Limit in Setting Refer to the “Power-On Fixed” sheet.
Exception None
Remarks • In “Variable” setting, the power operation is in wait for 1 sec. and then turned off when the main power switch is off.
2) MAXIMUM VOLUME
Selection Adjustment from 0 to 60 (no loop)
Default 60
Explanation Sound volume can not be adjusted higher than the preset value.
Limit in Setting • When the sound volume is set lower than 59, only figures are displayed and the sound volume bar is not displayed.
• The maximum sound volume for ON-timer (Wake up timer) is limited also to the preset value.
Exception
Remarks • When the sound volume is set higher than the MAX setting by the adjusting process, the sound volume control operation is
prohibited for turn-up and the sound volume should be turned down to MAX in this state.
3) VOLUME FIXED
Selection Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
Default Variable
Explanation • FIXED: Fixed at the level adjusted for a fixed volume.
• AC CTRL: Start-up at the level specified for a fixed volume at ACON.
• AC/RC CTRL: Start-up at the level specified for a fixed volume at start.
Limit in Setting • The sound volume for the ON-timer (Wake up timer) is fixed also without display of menu. Besides, the setting is made
impossible. (Basically, the menu is not displayed.)
• The following keys become invalid:
• Sound volume Up/Down (VOL +/–) [for both remote control and the unit]
• Mute (MUTE)
Exception • In the item “VOLUME” of adjustment process, the sound volume can be set freely irrespective of this setting.
Remarks • As for sound volume fixing and sound volume MAX level, the sound volume fixing has priority.
• Once the sound volume has been changed by adjustment process, it should be set back to the sound volume preset by
sound volume fixing level when the adjustment process ends.
4) VOLUME FIXED LEVEL
Selection Adjustment from 1 to 60 (no loop)
Default 20
Explanation The sound volume to be fixed by “Volume fixed” is determined.
Limit in Setting None
Exception None
Remarks Setting is valid only when “Volume fixed” is selected for “fixed”.
5) RC BUTTON
Selection Selection between “Respond”, “No Respond” and “Limited” (loop provided)
Default Respond
Explanation Making the remote controller settings.
• At the “No Respond” setting, the remote controller keys are disabled. Its power key (reception/standby key) is disabled too.
• At the “Limited” setting, some channel-related keys alone are operative. All the other remote controller keys (power, volume
/ , channel / , light control (brightness sensor), broadcast select) are inoperative.
Limit in Setting In “No respond” setting, all the keys (including the power key) are not accepted.
Exception • Adjustment process, inspection process and hotel only keys are valid irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
5 – 18
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
6) PANEL BUTTON
Selection Selection between “Respond” and “No respond” (loop provided)
Default Respond
Explanation All the operations by keys (except the power key) of the unit can be invalidated.
Limit in Setting
Exception • Adjustment process, inspection mode and hotel menu mode can be started irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
7) MENU BUTTON
Selection Selection between “Respond” and “No respond” (loop provided)
Default Respond
Explanation In “No respond” setting, the menu operation by the menu key of the remote control and the menu key of the unit are invali-
dated.
Limit in Setting
Exception • Adjustment process, inspection mode and hotel menu mode can be started irrespective of setting.
• All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
Remarks
8) ON SCREEN DISPLAY
Selection Selection between “Yes”, “No” (loop provided)
Default Yes
Explanation • At the “No” setting, the following items are not displayed on screen: register, setting, adjustment menu, channel call and vol-
ume bar.
On the wide-screen models, an input selection is immediately made because the menu is not displayed.
• At the “Limited” setting, some items cannot be displayed on screen.
On the Japan-destined models, the channel call “Message” alone cannot be displayed. (This is because the channel call mes-
sage may be confused with a message being sent from the hotel.)
On the North America-destined models, the OSD works the same as at the “No” setting.
Limit in Setting • Keys falling under any of the following items become invalid.
Appearance of screen changes and the sound changes.
Personal functions which are hard to restore.
Screen display, menu, OFF-timer, ON-timer, AV MODE, screen size switching, clock setting, treble emphasis, AUDIO ONLY,
sound changeover, LANGUAGE, CLOSED CAPTION
Others • Simple input switching is generated. Those which are restored soon after leaving as they are and may be requested for
change by customer are not prohibited.
Brightness sensor (BACKLIGHT) and PIC. FLIP
Exception • Such a caution which is displayed independently is displayed as it is.
Non-responding signal caution
Remarks • When CC has already been ON, CLOSED CAPTION is displayed.
9) INPUT MODE START
Selection Selection between “Normal”, “Air ( )”, “INPUT 1/2/3”, “PC”, “HDMI 1/2/3/4/5”, “DVI” (loop provided)
Default Normal
Explanation In power-ON, the input source to be started or channel can be set.
(In standard mode, the operation follows the last memory.)
About options • All the input sources in the model are made selectable.
• In TV mode, the channel to be set follows the last memory and the content of the last memory is included in the notation by
options. Ex.) Air (2), Cable (98.1) etc.
Limit in Setting • The display of channel setting menu and the channel setting operation are prohibited.
Exception
Remarks • In setting at “Normal”, the setting of “Input mode fixed” is changed to “Variable” and selection should be prohibited.
5 – 19
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
10)INPUT MODE FIXED
Selection Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided)
Default – (Variable)
Explanation • At the “Fixed” setting, the TV set gets started with the settings of “Input mode start”, and then any other channels and inputs
are not accepted.
• At the “ACON (AC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under AC control.
• At the “AC/RCON (AC/RC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under either control.
Limit in Setting • With the execution of hotel mode, the input source is forced to change to that set by “Input mode start” and the channel
switching and input switching are prohibited thereafter.
• ON-timer's (Wake-up timer) channel items are not displayed or the operation is prohibited. (Basically, they are not displayed.)
• The following keys are invalidated.
CH / , direct tuning button, FLASHBACK, input
However, the keys (input switching and CH / keys) of the unit for menu operation remain valid.
Exception None
Remarks • In the following case, setting is cancelled and mode is changed to “Variable”.
When the setting of “Input mode start” is set to “Normal”.
11)RC_PATH_THROUGH
Selection Selection between “OFF”, “ON: TV RCE” and “ON: TV RCD” (loop provided)
Default OFF
Explanation Function to feed the remote controller-received signal to Pin 9 (open) on the RS232C.
Limit in Setting None
Exception None
Remarks None
12)AV POSITION FIXED
Selection Selection between “Variable” and “Fixed” (loop provided)
Default Variable
Explanation In case of “Fixed” setting,
– Menu “Picture” and “Audio” setting can't be changed like “Dynamic (Fixed)”.
– When “AV Mode” key is pressed, TV just displays current AV Mode (cannot be changed.).
Limit in Setting None
Exception None
Remarks • When receiving with AV Position key, OPC, Dolby key and other direct audio select keys, the current display stays on and no
setting can be changed.
• Even by initializing personal information, the hotel-mode settings are kept intact. In this way, the AV positions, video and
audio adjustment settings are not initialized.
13)LOUD SPEAKER (ON/OFF)
Selection Selection between “ON” and “OFF” (loop provided)
Default ON
Explanation If “OFF” is selected, TV stops Speaker output even without Headphone connected.
Limit in Setting None
Exception None
Remarks • Press the volume UP/DOWN key, and the mute icon appears for 4 seconds.
• The mute key and audio-related keys are displayed with caution.
• Usually, the headphones and monitor audio outputs can be adjustable.
14)232C POWON
Selection Selection between “Disable” and “Enable” (loop provided)
Default Disable
Explanation In the standby mode, the power-on by the 232C command is enabled or disabled.
Limit in Setting None
Exception None
Remarks None
5 – 20
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
15)PUBLIC MODE (ON/OFF)
Selection Selection between “ON” and “OFF” (loop provided)
Default OFF
Explanation In case of “ON”, public mode settings are effected.
Limit in Setting None
Exception None
Remarks The public-mode settings are operable only when this item is set at ON.
5 – 21
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 6. TROUBLESHOOTING TABLE
LC-40LE830U
Service Manual
[1] Failure diagnosis by LED in front of cabinet
START
Yes
Is the Center Icon flashing? Check "[2] LED flashing specification at the time of an error (Center icon LED used)".
No
Is the Center Icon lighting No
Check Power-Unit and AC-cable.
When AC plug on?
Yes
No
Is the Backlight lighting? Check "LED Backlight does not turn on.".
Yes
Check "Picture does not display.".
[2] LED flashing specification at the time of an error (Center icon LED used)
1. Display method
• Since only the center icon LED can be used, slow flashing and fast flashing are combined.
• Refer to Table 1.
• The Start from the detail display. (No outline display)
• After recovering from an error, if the same error cannot be generated again, refer to MONITOR ERR CAUSE on the process screen.
• During version upgrade, the brightness of the flashing LED changes smoothly.
• When completing version upgrade, the brightness of the LED changes in a staircase pattern.
2. LED flashing method
Error flashing
<Detail display example>
Center icon ON
OFF
1600ms 1600ms
400ms
400ms 300ms
100ms
• Flashing during Verup
ON
Center icon OFF
500ms
500ms
• Flashing when completing Verup
ON
Center icon OFF
1000ms 1000ms 1000ms 1000ms
6–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
Table 1. Concrete flashing pattern
Detail display
Item Cause
Slow flashing Fast flashing
Inverter/Lamp system failure Flashes once Flashes once Lamp error
Power PWB Flashes twice Flash once Power supply error 2 (*2) AC_DET error
failure Flash twice Power supply error 2 (*2) UR+13V error
(Power failure, etc.) Flash 3 times Power supply error 2 (*2) D+3.3V error
Flash 5 times Panel power supply error
Main PWB Flashes 3 times Flashes once Initial communication error
failure Flashes twice Start-up confirmation communication error
(Communication Flashes 3 times Regular communication error
failure, etc.) Flashes 5 times Other communication error
Others Flashes 4 times Flashes once Temperature error
Flashes twice Sync error
Flashes 3 times Notification from the main microcomputer (*3)
VerUP executing Flashes smoothly None Version upgrading
VerUP succeeded Flashes in a staircase pattern None Version upgrade succeeded
VerUP failed None Flashes continuously Version upgrade failed
ROM data failure None Flashes continuously Start-up after failing version upgrade (*4)
*2: They depend on the system. Power supply error is defined from product to product.
*3: For details, refer to ERROR STANDBY CAUSE on the adjustment process screen.
*4: If the boot section is abnormal, there is no flashing (flashing impossible).
3. New method
Center icon
1600ms 1600ms
400ms
400ms 300ms
100ms
Flashing during Verup
Center icon
500ms
500ms
Flashing when completing Verup
Center icon
1000ms 1000ms 1000ms 1000ms
6–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
LED flashing timing chart at the time of an error
100ms 400ms 1.6sec
1) Inverter/Lamp failure details (Flashes slowly once and flashes fast) Note
Pins are monitor microcomputer pins unless other-
Error type Center icon LED operation
wise specified.
Lamp failure H: On ERR_PNL(19pin): Hi failure. Confirmed after 8 consecu-
Flashes fast once tive detections at 64msec intervals (detected only when
the backlight is on).
Note that after five detection counts, the lamp cannot be
L: Off
activated except in the monitor process.
Accumulated counts are cleared to 0 by the setting in the
process A.
2) Power failure details (Flashes slowly twice and flashes fast) Note
Pins are monitor microcomputer pins unless other-
Error type Center icon LED operation
wise specified.
PS_ON H: On AC_DET(28pin) failure(L).
AC_DET failure If error is detected during start-up or operation by inter-
Flashes fast once rupt, the power is turned on again.
L: Off
SM_POW H: On DET_13V(32pin) failure (L). Main 13V is not applied.
Main 13V failure
Flashes fast twice If error is detected during start-up or operation, the power
is turned on again by polling.
L: Off
D_POW H: On DET_D3V3(33pin) failure (L). Digital 3.3V is not applied.
Digital 3.3V failure
Flashes fast 3 times If error is detected during start-up or operation, the power
is turned on again by polling.
L: Off
PANEL_POW H: On DET_PNL12V(34pin) failure (L). Panel power is not
Panel 12V failure applied.
Flashes fast 5 times
Detection is started after turning on the panel power and
L: Off
receiving command; the power is turned off by polling.
3) Communication failure details (Flashes slowly 3 times and flashes fast) Note
Basically, debug print logs are analyzed or commu-
Error type Center icon LED operation
nication logs are analyzed by a bus monitor.
Initial communica- H: On Initial communication from the main CPU is not
tion reception failure received. (Request for the monitor model No. is not
Flashes fast once received.)
→ Communication line failure or main CPU start-up fail-
L: Off
ure
Start-up confirma- H: On Start-up reason confirmation from the main CPU cannot
tion reception failure be received. (Start-up communication until start-up rea-
Flashes fast twice son notification command is not received.)
→ Main CPU start-up failure or monitor microcomputer
L: Off
reception failure
Regular communica- H: On Regular communication that is performed at 1 second
tion failure intervals in the normal operation is interrupted.
Flashes fast 3 times → Main CPU operation failure or monitor microcom-
puter reception failure
L: Off
Other communica- H: On When a request (PM_REQ=H) is sent from the main
tion failure microcomputer, the request command is not output
Flashes fast 5 times from the main CPU, etc.
L: Off → Main CPU operation failure or monitor microcom-
puter reception failure
6–3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
4) Other failure details (Flashes slowly 4 times and flashes fast) Note
Pins are monitor microcomputer pins unless other-
Error type Center icon LED operation
wise specified.
Monitor temperature H: On If the panel temperature is 60°C or more for 15 seconds
failure or more in a row, CAUTION appears on the OSD
Flashes fast once (flashes in red in the lower right screen).
L: Off If the panel temperature is 60°C or more for 25 seconds
or more in a row, error standby is activated.
(MONITOR MAX TEMP on page 15 of the process A:
Change of temperature failure AD value): Thermistor
Main failure H: On Main microcomputer detection error (CPU temperature
Flashes fast 3 times error, etc.)
The details are displayed on page 1 of the process A of
the main microcomputer.
L: Off
6–4
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[3] TROUBLESHOOTING TABLE
• LED Backlight does not turn on.
If it is not an error of power supply/LED driver,
It is start-up in the lamp error disregard mode.
Do you start?
YES
When main unit is replaced , does it start normally?
YES NO
Replace main unit. en LCD control unit is replaced ,does it start normally?
YES
Replace LCD control unit
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
If it is not an error of power supply/LED driver,
It is start-up in the lamp error disregard mode.
Do you start?
NO
When power supply unit is replaced, does it start normally?
YES
Replace power supply unit.
NO
When main unit is replaced , does it start normally?
YES
Replace main unit.
NO
When LCD control unit is replaced ,does it start normally?
YES
Replace LCD control unit.
NO
When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
When the parts in the panel cannot be replaced. →Replace panel module.
6–5
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
Trouble Shooting Panel Module
When C-S FPC (4pieces (for LE835) or 2pieces (for LE830/831/832) is replaced, does screen display normally?
YES
Replace C-S FPC (4pieces (for LE835) or 2pieces(for LE830/831/832).
NO
When C-PWB is replaced, does screen display normally?
YES
Replace C-PWB.
(Adjust “VCOM ADJ” after replace C-PWB)
NO
Replace Panel HIRAKI.
(Adjust “VCOM ADJ” after replace Panel HIRAKI)
6–6
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
• Picture does not display.
No video (1)
COMPOSITE: No external input video [INPUT-6] COMPOSITE: No external input video [INPUT-7]
Is INPUT-6 selected on the input select menu screen? Is INPUT-7 selected on the input select menu screen?
NO NO
Select INPUT-6 on the input select menu Select INPUT-7 on the input select menu
screen for the right input signal. screen for the right input signal.
YES YES
Is there the COMPOSITE signal input at pin (AJ23) of Is there the COMPOSITE signal input at pin (AK22) of IC3303
IC3303 (CPU)? (CPU)?
NO NO
Check the line between pin (10) of J510 Check the line between pin (5) of J510 and
and pin (AJ23) of IC3303. pin (AK22) of IC3303.
YES YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN(40pin), VBO_LOCKN(39pin) of P2604 become Low if there is no problem
in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–7
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No video (2)
COMPONENT: No external input video [INPUT-5]
Is INPUT-5 selected on the input select menu screen?
Is the INPUT-SELECT for the input signal?
NO
Select INPUT-5 on the input select menu screen for the
right input signal.
Does the COMP1_PLUG detection function?
Check the line between pin (17) of input terminal (J510)
and pin (L32) of IC3303 (CPU).
YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN (40pin), VBO_LOCKN (39pin) of P2604 become Low if there is no
problem in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–8
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No video (3)
No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception
Is the specified TV signal selected on the input select menu screen?
Is there the analog video signal output (CVBS) at pin (9) of Are there the IF signal outputs (D_IF+/-) at the pins (11) and (10) of tuner
tuner (TU1105)? (TU1105)?
NO NO
Check TU1105 and its peripheral circuits Check the line between TU1105 and IC4405, and
(TU_SDATA: Pin4 of TU1105 their peripheral circuits (C4463/C4464/R1158, etc.).
TU_SCLK: Pin5 of TU1105, etc.).
YES YES
Is there the analog video signal input at pin (AK24) of IC3303 Are there the TS signal outputs (ATSC_TS_D0/SYNC/CLK/VAL) at the
(CPU)? pins (33), (34), (37) and (38) of Demodulator (IC4405)?
NO NO
Check the line between IC3303 and TU1105, and Check the line between IC4405 and IC3303, and
their peripheral circuits. their peripheral circuits (R4450/R3365/R3432, etc.).
YES YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN (40pin), VBO_LOCKN (39pin) of P2604 become Low if there is no
problem in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6–9
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No video (4)
PC: No external input video [INPUT-8]
Is INPUT-8 selected on the input select menu screen?
NO
Select INPUT-8 on the input select menu screen for the right input signal.
Is IC1504 (HDMI switch) accessed by I2C, with PC connected, to read the VGA_SCL/SDA data?
Check the DDC line and its peripheral circuits. (IC504 and its peripherals).
YES
Are there the video signal inputs at pins (AK15) (G), (AK13) (B) and (AM15) (R) of IC3303 (CPU)?
Are there the VSYNC/HSYNC signal inputs at pins (AM13) and (AL13) of IC3303?
NO
Check the line between SC501 and IC3303.
YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN (40pin), VBO_LOCKN (39pin) of P2604 become Low if there is no
problem in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 10
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
<HDMI input> No video (5)-1
HDMI: No external input video [INPUT-1]
Is INPUT-1 selected on the input select menu screen? NO Select INPUT-1 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? Check the line between the input terminals of
NO SC1503 and IC1504.
Does the DDC5V signal come from pin (18) of SC1503 to pin (60) of IC1504 Check IC1504 and its peripheral circuits
(HDMI_SW)? (SDA1_400K: pin70 of IC1504/SCL1_400K: pin71
of IC1504, etc.).
YES
Does the HPD signal come from pin (59) of IC1504 to pin (19) of SC1503? NO Check the line between the pin (59) of IC1504 and
the pin (19) of SC1503.
Check IC1504 and its peripheral circuits
(SDA1_400K: pin70 of IC1504/SCL1_400K: pin71
of IC1504, etc.).
YES
Are there the TMDS signal inputs at pins (26/27) (CLK-/+), (28/29) (D0-/+), (30/31) NO Is IC1504 (pin57/pin58) accessed by I2C, with
(D1-/+), (32/33) (D2-/+), all of IC1504? HDMI connected, to read the DDC_I2C SDA/SCL
data?
NO
Check the DDC line and its peripheral circuits.
(IC1504 and its peripherals).
YES
Are there the all of TMDS inputs at pins (AM9/AL9) (CLK-/+), (AM10/AL10) (D0-/+), NO Check the line between IC1504 and IC3303, and
(AM11/AL11) (D1-/+), (AM12/AL12) (D2-/+) of IC3303 (CPU)? their peripheral circuits.
YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN (40pin), VBO_LOCKN (39pin) of P2604 become Low if there is no
problem in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 11
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
<HDMI input> No video (5)-2
HDMI: No external input video [INPUT-2]
Is INPUT-2 selected on the input select menu screen? NO Select INPUT-2 on the input select menu screen
for the right input signal.
YES
Does the HOT PLUG detection function? Check the line between the input terminals of
NO SC1502 and IC1504.
Does the DDC5V signal come from pin (18) of SC1502 to pin (75) of IC1504 Check IC1504 and its peripheral circuits
(HDMI_SW)? (SDA1_400K: pin70 of IC1504/SCL1_400K:
pin71 of IC1504, etc.).
YES
Does the HPD signal come from pin (74) of IC1504 to pin (19) of SC1502? NO Check the line between the pin (74) of IC1504
and the pin (19) of SC1502.
Check IC1504 and its peripheral circuits
(SDA1_400K: pin70 of IC1504/SCL1_400K:
pin71 of IC1504, etc.).
YES
Are there the TMDS signal inputs at pins (17/18) (CLK-/+), (19/20) (D0-/+), (21/22) NO Is IC1504(pin72/pin73) accessed by I2C, with
(D1-/+), (23/24) (D2-/+), all of IC1504? HDMI connected, to read the DDC_I2C SDA/SCL
data?
NO
Check the DDC line and its peripheral circuits.
(IC1504 and its peripherals).
YES
Are there the all of TMDS inputs at pins (AM9/AL9) (CLK-/+), (AM10/AL10) (D0-/+), NO Check the line between IC1504 and IC3303, and
(AM11/AL11) (D1-/+), (AM12/AL12) (D2-/+) of IC3303 (CPU)? their peripheral circuits.
YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN(40pin), VBO_LOCKN(39pin) of P2604 become Low if there is no
problem in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 12
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
<HDMI input> No video (5)-3
HDMI: No external input video [INPUT-3]
Is INPUT-3 selected on the input select menu screen? NO Select INPUT-3 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? Check the line between the input terminals of
NO SC1501 and IC1504.
Does the DDC5V signal come from pin (18) of SC1501 to pin (56) of IC1504 Check IC1504 and its peripheral circuits.
(HDMI_SW)? (SDA1_400K: pin70 of IC1504/SCL1_400K: pin71
of IC1504, etc.).
YES
Does the HPD signal come from pin (55) of IC1504 to pin (19) of SC1501? NO Check the line between the pin (55) of IC1504 and
the pin (19) of SC1501.
Check IC1504 and its peripheral circuits
(SDA1_400K: pin70 of IC1504/SCL1_400K: pin71
of IC1504, etc.).
YES
Are there the TMDS signal inputs at pins (8/9) (CLK-/+), (10/11) (D0-/+), (12/13) NO Is IC1504 (pin53/pin54) accessed by I2C, with HDMI
(D1-/+), (14/15) (D2-/+), all of IC1504? connected, to read the DDC_I2C SDA/SCL data?
NO
Check the DDC line and its peripheral circuits.
YES (IC1504 and its peripherals).
Are there the all of TMDS inputs at pins (AM9/AL9) (CLK-/+), (AM10/AL10) (D0-/+), NO Check the line between IC1504 and IC3303, and
(AM11/AL11) (D1-/+), (AM12/AL12) (D2-/+) of IC3303 (CPU)? their peripheral circuits.
YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN (40pin), VBO_LOCKN (39pin) of P2604 become Low if there is no
problem in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 13
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
<HDMI input> No video (5)-4
HDMI: No external input video [INPUT-4]
Is INPUT-4 selected on the input select menu screen? NO Select INPUT-4 on the input select menu screen for
the right input signal.
YES
Does the HOT PLUG detection function? Check the line between the input terminals of SC1505
NO and IC1504.
Does the DDC5V signal come from pin (18) of SC1505 to pin (51) of IC1504 Check IC1504 and its peripheral circuits
(HDMI_SW)? (pin70 of IC1504/SCL1: pin71 of IC1504, etc.).
YES
Does the HPD signal come from pin (50) of IC1504 to pin (19) of SC1505? NO Check the line between the pin (50) of IC1504 and the
pin (19) of SC1505.
Check IC1504 and its peripheral circuits
pin70 of IC1504/SCL1: pin71 of IC1504, etc.).
YES
Are there the TMDS signal inputs at pins (99/100) (CLK-/+), (1/2) (D0-/+), (3/4) NO Is IC1504 (pin48/pin49) accessed by I2C, with HDMI
(D1-/+), (5/6) (D2-/+), all of IC1504? connected, to read the DDC_I2C SDA/SCL data?
NO
Check the DDC line and its peripheral circuits.
YES (IC1504 and its peripherals)
Are there the all of TMDS inputs at pins (AM9/AL9) (CLK-/+), (AM10/AL10) (D0-/ NO Check the line between IC1504 and IC3303, and their
+), (AM11/AL11) (D1-/+), (AM12/AL12) (D2-/+) of IC3303 (CPU)? peripheral circuits.
YES
In LE835U.
Are the LVDS signal input to the pin of P2601? NO Check IC3303 and its peripheral circuits.
LVDS0_FPGA_D0P/N (39/40pin), LVDS0_FPGA_D1P/N (37/38pin), (IC3501/IC3502, etc)
LVDS0_FPGA_D2P/N (35/36pin), LVDS0_FPGA_D3P/N (30/31pin),
LVDS0_FPGA_D4P/N (28/29pin), LVDS0_FPGA_CLKP/N_74MHz (32/33pin),
LVDS1_FPGA_D0P/N (25/26pin), LVDS1_FPGA_D1P/N (23/24pin),
LVDS1_FPGA_D2P/N (21/22pin), LVDS1_FPGA_D3P/N (16/17pin),
LVDS1_FPGA_D4P/N (14/15pin), LVDS1_FPGA_CLKP/N_74MHz (18/19pin).
In LE830U/LE831U/LE832U.
Is the T-CON PWB connected? NO Check the panel module and harness.
VBO_HTPDN (40pin), VBO_LOCKN (39pin) of P2604 become Low if there is
no problem in the connection.
YES
Are the V-By-One signal input to the pin of P2604? NO Check IC3303 and its peripheral circuits.
VBO_CN_TXA+/- (36/37pin), VBO_CN_TXB+/- (32/33pin), (IC3501/IC3502/IC3503, etc)
VBO_CN_TXC+/- (28/29pin), VBO_CN_TXD+/- (24/25pin).
YES
Check the panel module and harness.
6 – 14
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
• Does not sound.
No audio (1)
INPUT-6 No audio. INPUT-7 No audio. INPUT-5 No audio.
Is INPUT-6 selected on the input select Is INPUT-7 selected on the input select Is INPUT-5 selected on the input select
menu screen? menu screen? menu screen?
NO NO NO
Refer to “: No external input Refer to “: No external input Refer to “: No external input
video [INPUT-6]”. video [INPUT-7]”. video [INPUT-5]”.
YES YES YES
Is the audio output selected for “VARI- Is the audio output selected for “VARI- Is the audio output selected for “VARI-
ABLE” on the menu screen? ABLE” on the menu screen? ABLE” on the menu screen?
NO NO NO
Set the audio output to Set the audio output to Set the audio output to
“FIXED”. “FIXED”. “FIXED”.
YES YES YES
Does the audio signal come from pins (8) Does the audio signal come from pins (3) Does the audio signal come from pins (13)
(L) and (7) (R) of input terminal (J510) to (L) and (2) (R) of input terminal (J510) to (L) and (12) (R) of input terminal (J510) to
pins (AL30)(L) and (AL32) (R) of IC3303 pins (AL27)(L) and (AK28) (R) of IC3303 pins (AK27)(L) and (AK29) (R) of IC3303
(CPU)? (CPU)? (CPU)?
NO NO NO
Check the line between J510 Check the line between J510 Check the line between J510
and IC3303. and IC3303. and IC3303.
YES YES YES
Does the digital audio signal come from pins (Y31/Y30/V27) (CPU_AOBK/AOLRCK/AOSDATA0) of IC3303 (CPU) to pin (8/9/7) (SP_BCLK/
SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3303
and IC2701, and their periph-
eral circuits.
YES
• About the L/R Speakers. NO Check IC2701 and its peripheral circuits.
Does the digital audio signal come from pins (47/43/ (X2701, etc.).
44/45) of IC2701 (Audio DSP) to pin (5/8/7/6) of
IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/
44/46) of IC2701 (Audio DSP) to pin (5/8/7/6) of
IC2702 (AMP for SW)?
YES
• About the L/R Speakers. NO • About the L/R Speakers.
Is the audio output from IC2703 as specified? Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker. • About the Subwoofer Speaker.
IS the audio output from IC2702 as specified? Check IC2702 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their
peripheral circuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker
and their peripheral.
6 – 15
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No audio (2)
[PC analog audio input] INPUT-8 No audio. [HDMI analog audio input] INPUT-2 No audio.
Is INPUT-8 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen?
NO NO
Refer to “: No external input video [INPUT-8]”. Refer to “: No external input video [INPUT-2]”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? Is the audio output selected for “VARIABLE” on the menu screen?
NO NO
Set the audio output to “FIXED”. Set the audio output to “FIXED”.
YES YES
Is the “PC input” - “Audio select” selected for “Video + Audio” on the Is the “PC input” - “Audio select” selected for “HDMI + Analog” on
menu screen? the menu screen?
NO NO
Set the “PC input” - “Audio select” to “Video + Set the “PC input” - “Analog select” to “HDMI +
Audio”. Analog.
YES YES
Does the digital audio signal come from pins (Y31/Y30/V27) (CPU_AOBK/AOLRCK/AOSDATA0) of IC3303 (CPU) to pin (8/9/7) (SP_BCLK/
SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3303 and IC2701,
and their peripheral circuits.
YES
• About the L/R Speakers. NO Check IC2701 and its peripheral circuits. (X2701, etc.).
Does the digital audio signal come from pins (47/43/44/45) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/44/46) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2702 (AMP for SW)?
YES
• About the L/R Speakers. NO • About the L/R Speakers.
Is the audio output from IC2703 as specified? Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker. • About the Subwoofer Speaker.
IS the audio output from IC2702 as specified? Check IC2702 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their peripheral cir-
cuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker and their periph-
eral.
6 – 16
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No audio (3)
No audio at UHF/VHF broadcast signal reception. No audio at digital broadcast signal reception.
Is TV selected on the input select menu screen? Is TV selected on the input select menu screen?
NO NO
Refer to “No video at UHF/VHF broadcast signal Refer to “No video at digital broadcast signal
reception”. reception”.
YES YES
Is the audio output selected for “VARIABLE” on the menu screen? If no video appears, refer to “No video at digital broadcast signal
reception”.
NO
Set the audio output to “FIXED”. Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
YES
Is there the SIF signal output at pin (8) of tuner (TU1105)?
NO
Check the tuner (TU1105) and its peripheral cir-
cuits.
(I2C line: TUNER_SCL/TUNER_SDA, etc.)
YES
Does the SIF signal come from pin (8) of TU1105 (tuner) to pin
(AM24) of IC3303 (CPU)?
NO
Check the line between TU1105 and IC3303, and
their peripheral circuits.
YES YES
Does the digital audio signal come from pins (Y31/Y30/V27) (CPU_AOBK/AOLRCK/AOSDATA0) of IC3303 (CPU) to pin (8/9/7) (SP_BCLK/
SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3303 and IC2701, and
their peripheral circuits.
YES
• About the L/R Speakers. NO Check IC2701 and its peripheral circuits. (X2701, etc.).
Does the digital audio signal come from pins (47/43/44/45) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/44/46) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2702 (AMP for SW)?
YES
• About the L/R Speakers. NO • About the L/R Speakers.
Is the audio output from IC2703 as specified? Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker. • About the Subwoofer Speaker.
IS the audio output from IC2702 as specified? Check IC2702 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their peripheral cir-
cuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker and their periph-
eral.
6 – 17
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No audio (4)
INPUT-1 No audio (HDMI connected)
INPUT-2 No audio (HDMI connected)
INPUT-3 No audio (HDMI connected)
INPUT-4 No audio (HDMI connected)
[INPUT-1 input]
Is INPUT-1 selected on the input select menu screen?
[INPUT-2 input]
Is INPUT-2 selected on the input select menu screen?
[INPUT-3 input]
Is INPUT-3 selected on the input select menu screen?
[INPUT-4 input]
Is INPUT-4 selected on the input select menu screen?
NO
Refer to “: No external input video [INPUT-1/2/3/4]”.
YES
[INPUT-1 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-1]”.
[INPUT-2 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-2]”.
[INPUT-3 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-3]”.
[INPUT-4 input]
If no video appears, refer to “No external input video (HDMI) [INPUT-4]”.
Is the audio output selected for “VARIABLE” on the menu screen?
NO
Set the audio output to “FIXED”.
YES
Does the digital audio signal come from pins (Y31/Y30/V27) (CPU_AOBK/AOLRCK/AOSDATA0) of IC3303 (CPU) to pin (8/9/7) (SP_BCLK/
SP_LRCLK/SP_DATA) of IC2701 (Audio DSP)?
NO
Check the line between IC3303 and
IC2701, and their peripheral circuits.
YES
• About the L/R Speakers. NO Check IC2701 and its peripheral circuits. (X2701, etc.).
Does the digital audio signal come from pins (47/43/44/45) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2703 (AMP for L/R)?
• About the Subwoofer speaker.
Does the digital audio signal come from pins (47/43/44/46) of
IC2701 (Audio DSP) to pin (5/8/7/6) of IC2702 (AMP for SW)?
YES
• About the L/R Speakers. NO • About the L/R Speakers.
Is the audio output from IC2703 as specified? Check IC2703 and its peripheral circuits.
• About the Subwoofer Speaker. • About the Subwoofer Speaker.
IS the audio output from IC2702 as specified? Check IC2702 and its peripheral circuits.
YES
• About the L/R Speakers.
Check the connector (P2701) L/R speakers and their peripheral
circuits.
• About the Subwoofer Speaker.
Check the connector (P2702), subwoofer speaker and their
peripheral.
6 – 18
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No audio signal at Digital Audio Output terminal (Analog sound heard)
No INPUT-1/2/3/4 (HDMI) audio. No audio at digital broadcast signal reception.
If no video appears, refer to “No external input video (HDMI) If no video appears, refer to “No video at digital broadcast signal
[INPUT-1/2/3/4]”. reception”.
Is there the SPDIF signal output (CPU_ASPDIF) at pin (AA31) of IC3303 (CPU)?
NO
Check the IC3303 and its peripheral circuits.
YES
Is there the SPDIF signal (OPT_OUT) input at pin (2) of IC503 (SPDIF BUFFER & SPDIF-MUTE)?
NO
Check the line between IC3303 and IC503.
YES
Is there the MUTE signal input at pin (1) of IC503? (usual: High, Mute: Low)
NO
Check the AUDIO_MUTE and their peripheral circuits (Q505, etc.).
YES
Is there the SPDIF signal input at pin (1) of D527 (OPTICAL OUTPUT)?
YES NO
Check the speakers and the optical cable. Check D527 and its peripheral circuits.
No optical output under the following conditions as per HDMI requirements.
* Audio contents protected.
* Audio frequency beyond 48kHz.
* Audio bit length beyond 16bits.
6 – 19
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
No monitor audio output
Is the audio output from the monitor set at “VARIABLE” or “FIXED” on the menu screen?
NO
Check IC3303 (CPU) and its peripheral circuits.
YES
Are there the audio signal outputs at pins (AJ31) (HP_MON_L) and (AJ32) (HP_MON_R) of IC3303 (CPU)?
NO
Check IC3303 (CPU) and its peripheral circuits.
YES
Does the audio signal come from pins (2) (MONI_HP_L) and (11) (MONI_HP_R) of IC2704 (Line-out Amplifier) to pins (3) (L) and (2) (R) of J504?
NO
Check the line between IC2704 and J504 and their peripheral circuits.
Check the AUDIO_MUTE and HP_MUTE lines and its peripheral circuits (Q506,
YES
Q510, D2711, etc.).
Check the connector (J504) and their peripheral circuits, and speakers and the Cable.
No connect network
Does the signal come to 1pin of LAN-jack J9501? YES Check the interface device and peripheral circuits.
(see fig-1, fig-2) (power-LED of hub, LINK-LED of hub)
NO
Does the signal come to AD32 pin of IC3303? YES Check the line between J9501 and IC3303.
(see fig-2) Check the LAN-jack J9501.
NO
Check IC3303 and its peripheral circuits.
fig-1 LAN-jack J9501 fig-2
1pin
6 – 20
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 7. MAJOR IC INFORMATIONS Service
LC-40LE830U
Manual
[1] MAJOR IC INFORMATIONS
1. MAJOR IC INFORMATIONS
1.1. IC1504 (VHiSii9387+-1Q)
This IC is 5 input and 1 output HDMI port processor.
The TMDS cores run at 2.25Gbps. (Supports video resolutions up to 1080p, 60Hz, 12bit.)
The adaptive equalizer provides long cable support.
This IC has been pre-programmed with HDCP keys.
EDID and DDC support for 5 HDMI/DVI ports and 1 VGA port. (This IC includes 512-byte NVRAM and 256-byte SRAM for 5 HDMI ports and 128-byte
SRAM for VGA port.)
This IC supports the mandatory and several optional 3D formats described in the HDMI 1.4 Specification.
“Audio Return Channel” and “HDMI Ethernet Channel” support for one receiver port.
When changing this IC, please write EDID (how to write EDID is shown in Chapter 5 and section 10.1).
1.2. IC2001 (RH-iXD241WJN1Q)
The monitor microprocessor is intended to communicate with the main microprocessor and to operate the system.
It also controls power of the entire system.
1.3. IC2702, IC2703 (VHiYDA164BZ-1Y)
The Class-D type digital audio power amplifier YDA164BZ gives maximum continuous output of 10 W/ch or woofer output 15W.
1.4. IC3303 (RH-iXD220WJQZQ)
This LSI is FULL HIGH-DEFINITION 1080P DIGITAL TV SYSTEM-ON-A-CHIP.
It combines a transport de-multiplexer, a high definition video decoder, an AC3 audio decoder, a four-link LVDS transmitter, a V-by-One transmitter,
and an NTSC/PAL/SECAM TV decoder with a 3D comb filter (NTSC/PAL).
It supports Full-HD MPEG1/2/4/DiviX/VC1/RM/H.264/AVS video decoder standards, and JPEG.
Audio support includes a BTSC and a Dolby AC3/MPEG-2 Layer 1, 2, audio decoder.
A SPDIF output and a pair of analog outputs (L-R) are provided.
The LSI incorporates a complete ARM11-based microprocessor subsystem including caches with bridging to memory and a local bus, where external
peripherals can be attached.
Integrated peripherals include two USB 2.0, three UARTs, counter/timers and GPIO controllers.
1.5. IC3501, IC3502 (RH-iXD227WJQZQ)
These are 2G-bit (128M x 16bit) DDR3-1333 synchronous DRAM.
1.6. IC8401 (RH-iXD287WJQZQ)
The 2G-bit NAND flash memory device stores the main CPU program.
1.7. IC8455 (VHiR24064AS-1Y)
This is 64k-bit EEPROM device including the user setting.
1.8. IC506 (VHiM3221EiP-1Y)
This IC is a high speed, single-channel RS-232 transceiver interface device that operates from a single 3.3V power supply.
The device provides the electrical interface between an asynchronous communication controller and the serial-port connector.
This device operate at data signaling rates up to 460kbit/s.
All RS-232 (Tout and Rin) and CMOS (Tin and Rout) inputs and outputs are protected against electrostatic discharge (up to +/- 15kV ESD protection).
1.9. IC2704 (VHiAK4201EU-1Y)
This IC is audio amplifier for line-out/head-phone.
1.10. IC2701 (VHiYSS951VZ-1Y)
Audio DSP (YSS951VZ) has digital audio adjustment function (for example, PEQ, bass/treble, balance, bass enhancer, etc.) and adjusts TVs audio
quality.
1.11. IC4405 (VHiMT5112EE-1Q)
This IC is a demodulator for digital terrestrial HDTV(8VSB) and digital CATV(64/256QAM).
It is compliant with ATSC A/53, SCTE DVS-031, and ITU J.83 Annex B standards.
7–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
1.12. IC9505 (VHiPD720114-1Q)
This IC is a USB hub controller.
It has one upstream port and four downstream ports,
7–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 8. OVERALL WIRING/SYSTEM BLOCK DIAGRAM
LC-40LE830U
Service Manual
[1] OVERALL WIRING DIAGRAM (LC-40/46/52/60LE835U)
J
1 1
2 2
I
ޣPDޤ
POWER/LED Drive Unit 24
40"㧦RUNTKA786WJQZ
46"㧦RUNTKA790WJQZ 1
52"㧦RUNTKA794WJQZ
H 60"㧦RUNTKA798WJQZ
1 2 1 24
ޣSBޤ ޣPDޤ
ޣSPޤ
WOOFER RSP-ZA513WJQZ 1
5
G
USB
HDMI
ޣLWޤ
ޣACޤ 1
F 1 3 MAIN Unit
41
40"㧦DKEYMF733FM16
HDMI
46"㧦DKEYMF733FM14
52"㧦DKEYMF733FM13
60"㧦DKEYMF733FM12
HDMI
ޣPLޤ
1
E
4
HDMI
1
ޣRCޤ
15
1
1 4 ޣCIޤ
3
D LCD Control Unit ޣPLޤ
1 1
40"㧦RUNTK4909TPZS ޣLWޤ 6
ޣUBޤ
46"㧦RUNTK4909TPZW 41
52"㧦RUNTK4909TPZF TUNER
60"㧦RUNTK4909TPZA ETHER
USB NET
C
1 80 1 64 1 64 1 80
B
Touch Sensor Unit 1 12 1 6
RUNTKA811WJQZ ޣTKޣ ޤRAޤ
ޣRA ޤ1 5 ޣCI ޤ1 3 ޣUBޤ1 6
IR Emitter Unit
RUNTKA819WJQZ R/C, Operation Unit ICON Unit WiFi Unit
1 4 DUNTKF494FM01 DUNTKF770FM03 RUNTKA810WJQZ
ޣIRޤ
A
Rch㧦RSP-ZA511WJQZ (40"/46") Lch㧦RSP-ZA511WJQZ (40"/46")
LC-40/46/52/60LE835U Only RSP-ZA512WJQZ (52"/60")
RSP-ZA512WJQZ (52"/60")
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] OVERALL WIRING DIAGRAM (LC-40/46/52/60LE830U/832U/LC-60LE831U)
To LCD Panel
Module Unit
1 15
I
24
ޣPDޤ
1
POWER LED Drive Unit
H
40"䋺RUNTKA786WJQZ 1 2 1 24
46"䋺RUNTKA790WJQZ ޣSBޤ ޣPDޤ
52"䋺RUNTKA794WJQZ ޣSPޤ
WOOFER䋺RSP-ZA513WJQZ 60"䋺RUNTKA798WJQZ 1
5 MAIN Unit
G ޣLVޤ
1
41
ޣACޤ LC-40LE830U䋺DKEYMF733FM04 USB
LC-46LE830U䋺DKEYMF733FM03
F 1 3
LC-52LE830U䋺DKEYMF733FM02
LC-60LE830U䋺DKEYMF733FM01
HDMI
LC-40LE832U䋺DKEYMF733FM10
1
ޣPL ޤLC-46LE832U䋺DKEYMF733FM08
4 LC-52LE832U䋺DKEYMF733FM07
HDMI
1 LC-60LE832U䋺DKEYMF733FM06
E
15 LC-60LE831U䋺
ޣRCޤ DKEYMF733FM18
HDMI
1
HDMI
1 4 ޣCIޤ TUNER
D 3
LCD Control Unit ޣPLޤ 1
ޣLVޤ 1ޣUBޤ
40"䋺RUNTK4910TPZE 41 6
46"䋺RUNTK4910TPZC
52"䋺RUNTK4910TPZB USB ETHER
NET
C 60"䋺RUNTK4910TPZZ
1 80 1 80
Touch Sensor Unit 1 12 1 5 Lch
40, 46 : RSP-ZA511WJQZ
RUNTKA812WJQZ ޣTKޣ ޤRAޤ
ޣRA ޤ1 5 ޣCIޤ1 3 ޣUB ޤ1 6 52, 60 : RSP-ZA512WJQZ
R/C, Operation Unit ICON Unit WiFi Unit
Rch
DUNTKF494FM01 DUNTKF770FM02 RUNTKA810WJQZ
40, 46 : RSP-ZA511WJQZ
A 52, 60 : RSP-ZA512WJQZ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[3] SYSTEM BLOCK DIAGRAM (LC-40/46/52/60LE835U)
%8$5 %8$5A+0
+0276
.4 %8$5A+0A.4
/#+0 6%10
J
+0276 %8$5 %8$5A+0
.4 %8$5A+0A.4
+%A4'#&;
20.A'0 0A20.A'0
+0276 .4 %1/2A+0A.4
20.A92
%1/2A;2D2T
%QORQPGPV
1(.A(4%456
I /*\
䇼㪪㪧䇽 ::
:VCN +%A -*\ +%A -*\
ޣ.9ޤ2 R
㪧㪉㪎㪇㪈 8
52'#-'4 +% #/2A#A.4
㪜㪯㪫㪄㪪㪧 52#/2 %* 8
;&# +% 8 +% 8 8
䇼㪪㪧䇽 #/2A.4%-$%.-/%.- +%
&52 ''241/ 20.A+%A'0
9QQHGT 㪧㪉㪎㪇㪉 8 MDKV 5RNKVGT
+% ;55
㪜㪯㪫㪄㪪㪧 9QQHGT#/2 %* #/2A#A59 *%)&2
+%
;&# 4GUGV
7%1/A456
$7 8
&'6A20.8
#/2A*122 4'5'6 +1
H 0A2'4A456 .4A4'(
#/2A/76'
0A2'4A456 +1
0A#/2A2416'%6 0A#/2A2416'%6 +% 85;0%
+1
52A/76' 7%1/A/1&' 4%%
/1&' 6*'4/1
+:&9, 6JGTOKUVGT
)52 29/
#&
29/
#7&+1A/76'
57$/%7
/*\ ''241/A5%.
$7 8
$7 8 (. 5&#
+%
%8$5
.8&5176
+%
%8$5A1WV
:VCN 92 ''241/
%QORQPGPV
8 +
8 2/ 4'3 MDKV
ޣ2.ޤ20.8˴2 R
/*\ +% 8 +1
#65%&GOQF 8 8 #7&+1A/76' 0A/76'A#A#.. .#/2A'44
: &'/1&A65%.-5;0%8#.# +1 +1
:VCN /6'' 8
&A+( %27A6:&A7%1/%27A4:&A7%1/ 56$
7#46 +1
#65%A+(A#) 0A54'5'6 #%A&'6
G *&/+A%'%A+0
+1 +1
+1 5/219
%8$5
29/
+%
*&/+A%'%A176
#&
+1 +1
&'/1&A456 5/219*1.& 25A1
14
20. 8
67A5%.5&# 0
219A59
4%12%
+4A2#55
+%
)0&
5GNGEV
4%A%27
0A670A456 0A670A456 4%
5+(
67A&'/1&A5%.5&# -*\8
+%
219'47PKV
+%A -*\8 670'4A+% 4%
F 4(+0 +%A -*\8 +%A
67 8 +%A /6 (*& 810
8 56$A%27
#PCNQI +%A *8% +1
0A2'4A456
#7&+1A/76'
&KIKVCN 2%A85;0%*5;0% 8
4)$*8 #-#, 1(.
5K6WPGT 2%A4)$ &KIKVCN#8FGEQFG/CKP%27 29/A +%
4)$KP #- 1(. 5RNKVGT
29/A
&&%A+%A *%)&2
ޣ2&ޤ219'4˴2 R
*&/+A #%A&'6
&KUENGVG +5 5#.4%-5%.-
#7&+1A/76'
/WVG 20.A219
8 #WFKQQWV
+% /*\ 8
#WFKQ1WV *2/10+A.4 *2/10+A.4 29/
/KPK2NWI *2#/2 : +%
#-'7 : VCN 5RNKVGT
*%)&2
E 5+( 20.A+%A'0
5+(
8 +%
20.A219
25A10
#%A&'6
126+%#. +% %8$5A+0A.4
&&4 /
176 8 #7&+1A/76' %8$5A+0A.4 +%
)DKV
126A176 &&4 /
%1/2A+0A.4
)DKV /#+0
#WFKQKP
4)$*&/+ ˴&8
+0276 #WFKQ 2%*&/+A.4 2%*&/+A.4 &8 748
-'; 456
0#0&(NCUJ
/KPK2NWI 78
7#466:&
126A176
7#466:&
7#464:&
52+A(.#5*
10&&㨪
10&#㨪
7#464:&
&6852&+( ˴&8 58
7#46
˴/8
+..A.'&A56$;A75'+..A.'&
75$A
75$A
2%A85;0%*5;0% 4'5'6 $78
&8
+0276 &57$ 2%A4)$ 4'5'6 &8
$7 8
4)$ $CEM7R
D $7 8 $7 8 6T $7 8
+%
+%
7#46A%2761%7#46A%61%27 8 +%
5GNGEV
5GNGEV
$WHHGT 219'4%+4%7+6
8 .'&A&TKXG
㪠㪚㪌㪇㪍
㪩㪪㪉㪊㪉㪚㩷㪫㫏㪩㫏
+.. .'& 56$; 75
45%
㪤㪊㪉㪉㪈㪜㪠㪧
0QRKP4%2CUUVJTQWIJ 0A54'5'6
+...'&
8 5/219*1.&
&&%A 8 8
*&/+A +%
8 0#0&(.#5* 8 $7 8
)DKV
C +0276 &&%A 6T 6T
*&/+ *&/+A +%A -*\
+%A -*\
+%
+0276 *&/+59
&&%A
*&/+ 5++
*&/+A
*&/+ %'% 17
*&/+ %'% +
-';5%.-';5&#
+0276 &&%A
*&/+ *&/+A 748
4'3 219A59
W%1/ 8
.4A27.5'
4%12%
$7 8 8
+% 8
+0276 *&/+ &&%A $WHHGT $7 8
#4% *&/+A .%:(6
B *&/+A%'% *&/+A%'%
ޣ4%ޤ2 R ޣ%+ޤ2 R
,
ޣ+4 ޤR ޣ6- ޤR ޣ4# ޤR ޣ4#ޤ 2 R ޣ%+ޤ2 R
75$ 8
+% 78
# 2QYGT59
#2 +4 4%
8
'OKVVGT 6QWEJ5GPUQT 1RGTCVKQP +%10
+%
75$*WD 0A2'4A456 9K(K
%QPVTQNNGT 4%
2& 919.#0 12%
ޣ75ޤ9K(K
, : /*\
2 R
75$ 8 +% :VCN
A
R
# 2QYGT59 70+6
#2
,
8
'VJGTPGV
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[4] SYSTEM BLOCK DIAGRAM (LC-40/46/52/60LE830U/LE832U/LC-60LE831U)
%8$5 %8$5A+0
+0276 /#+0
.4 %8$5A+0A.4
.%&%QPVTQN7PKV
J
8$1A.1%-0
+0276 %8$5 %8$5A+0 8$1A*62&0
.4 %8$5A+0A.4
+%A4'#&;
20.A'0 0A20.A'0
.4 %1/2A+0A.4
+0276 20.A92
%1/2A;2D2T
%QORQPGPV
1(.A(4%456
I /*\
ޣ.8ޤ2 R
䇼㪪㪧䇽 ::
:VCN +%A -*\ +%A -*\
㪧㪉㪎㪇㪈 8
52'#-'4 +% #/2A#A.4
㪜㪯㪫㪄㪪㪧 52#/2 %* 8
;&# +% 8 +% 8 8
䇼㪪㪧䇽 #/2A.4%-$%.-/%.-
&52 ''241/ 20.A+%A'0 +%
9QQHGT 㪧㪉㪎㪇㪉 +% 8 MDKV 5RNKVGT
㪜㪯㪫㪄㪪㪧 #/2A#A59 ;55
9QQHGT#/2 %* *%)&2
+%
;&# 4GUGV
7%1/A456
$7 8
&'6A20.8
#/2A*122 4'5'6 +1
.4A4'(
H
#/2A/76'
0A2'4A456 0A2'4A456 +1
0A#/2A2416'%6 0A#/2A2416'%6 +% 85;0%
+1
52A/76' 7%1/A/1&' 4%%
/1&' 6*'4/1
+:&9, 6JGTOKUVGT
)52 29/
#&
29/
#7&+1A/76'
57$/%7
/*\
%8$5A1WV
$7 8 (. ''241/A5%.5&# $7 8
%8$5
:VCN +% +%
8$[1PG
%QORQPGPV
8 92 ''241/
2/ 4'3 +
ޣ2.ޤ20.8˴2 R
/*\ +% 8 8 +1 MDKV
: #65%&GOQF 8 &'/1&A65%.-5;0%8#.# 8 #7&+1A/76' 0A/76'A#A#.. .#/2A'44
:VCN /6'' 8 +1 +1
&A+( %27A6:&A7%1/%27A4:&A7%1/ 56$
7#46 +1
#65%A+(A#) 0A54'5'6 #%A&'6
G *&/+A%'%A+0
+1 +1
+1 5/219
%8$5
*&/+A%'%A176
#&
+%
+1 +1
&'/1&A456 5/219*1.& 25A1
14
20. 8
67A5%.5&# 0
219 59
4%12%
+4A2#55
+%
)0&
5GNGEV
4%A%27
0A670A456 0A670A456 4%
5+(
67A&'/1&A5%.5&# -*\8
+%
219'47PKV
+%A -*\8 670'4A+% 4%
F 4(+0 +%A -*\8 +%A
67 8 +%A /6 (*& 810
8 56$A%27
#PCNQI *8%
0A2'4A456
#7&+1A/76'
&KIKVCN 2%A85;0%*5;0% +%A +1 8
5K6WPGT 4)$*8 #-#, 1(. +%
2%A4)$ 29/A
4)$KP #- 1(. 5RNKVGT
&&%A+%A &KIKVCN#8FGEQFG/CKP%27 29/A *%)&2
ޣ2&ޤ219'4˴2 R
*&/+A #%A&'6
&KUENGVG +5 5#.4%-5%.-
#7&+1A/76'
/WVG 20.A219
+% 8 #WFKQQWV /*\ 8
#WFKQ1WV *2/10+A.4 *2/10+A.4 29/
/KPK2NWI *2#/2 : +%
#-'7 : VCN 5RNKVGT
*%)&2
E 5+( 5+( 20.A+%A'0
8 +%
20.A219
25A10
#%A&'6
126+%#. %8$5A+0A.4
+% &&4 /
176 #7&+1A/76' %8$5A+0A.4 +%
8 )DKV
126A176 %1/2A+0A.4 &&4 /
)DKV /#+0
#WFKQKP
4)$*&/+ ˴&8
+0276 2%*&/+A.4 2%*&/+A.4 8
#WFKQ &8 748
-'; 456
0#0&(NCUJ
/KPK2NWI +% 78
52+A(.#5*
126A176
10&&㨪
10&#㨪
7#464:&
7#466:&
7#464:&
7#466:&
&&4 / ˴&8 58
&6852&+(
˴/8
7#46
)DKV
+..A.'&A56$;A75'+..A.'&
75$A
75$A
2%A85;0%*5;0% \\ $78
4'5'6 &8
&57$ 2%A4)$ 4'5'6 $7 8 &8
+0276 4)$
$CEM7R
D +% $7 8 6T $7 8
+%
$7 8
5GNGEV
5GNGEV
7#46A%2761%7#46A%61%27 8 +%
$WHHGT 219'4%+4%7+6
8 .'&A&TKXG
㪠㪚㪌㪇㪍
㪩㪪㪉㪊㪉㪚㩷㪫㫏㪩㫏
+.. .'& 56$; 75
45%
㪤㪊㪉㪉㪈㪜㪠㪧
0A54'5'6
0QRKP4%2CUUVJTQWIJ
5/219*1.&
&&%A 8
8
*&/+A 8 +%
8 0#0&(.#5* $7 8
)DKV
C +0276 *&/+
&&%A 6T
*&/+A +%A -*\ +%A -*\
+%
+0276 *&/+59
&&%A
*&/+ 5++
*&/+A
*&/+ %'% 17
*&/+ %'% +
-'; 5%.-'; 5&#
+0276 *&/+ &&%A
4'3 219A59
*&/+A
W%1/ 8
$7 8
4%12%
8
+% 8
+0276 *&/+ &&%A $WHHGT $7 8
#4% *&/+A .%:(6
B *&/+A%'% *&/+A%'%
ޣ4%ޤ2 R ޣ%+ޤ2 R
, ޣ4#ޤ ޣ%+ޤ
ޣ6- ޤR ޣ4# ޤR
75$ 8 2 R 2 R
+% 78
# 2QYGT59
#2 4%
8 6QWEJ5GPUQT +%10
+%
1RGTCVKQP
75$*WD 0A2'4A456 9K(K
%QPVTQNNGT 4%
2& 919.#0 12%
ޣ75ޤ9K(K
, : /*\
2 R
75$ 8 +%
:VCN
R
2QYGT59
A #
#2
70+6
,
8
'VJGTPGV
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
8–4
PartsGuide
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
PARTS GUIDE
No. S21M760LE835U
LCD COLOR TELEVISION
LC-60LE831U
LC-40/46/52/60LE835U
LC-40/46/52/60LE830U
MODELS LC-40/46/52/60LE832U
CONTENTS
[1] PRINTED WIRING BOARD [7] SUPPLIED ACCESSORIES/
ASSEMBLIES PACKING PARTS
(LC-40LE835U/830U/832U)
[2] LCD PANEL MODULE UNIT
[8] SUPPLIED ACCESSORIES/
[3] CABINET PARTS PACKING PARTS
(LC-40LE835U/830U/832U) (LC-46LE835U/830U/832U)
[4] CABINET PARTS [9] SUPPLIED ACCESSORIES/
(LC-46LE835U/830U/832U) PACKING PARTS
(LC-52LE835U/830U/832U)
[5] CABINET PARTS
(LC-52LE835U/830U/832U) [10] SUPPLIED ACCESSORIES/
PACKING PARTS
[6] CABINET PARTS (LC-60LE835U/830U/831U/832U)
(LC-60LE835U/830U/831U/832U)
[11] SERVICE JIGS
(USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[1] PRINTED WIRING BOARD ASSEMBLIES
N DKEYMF733FM16 BW N X MAIN Unit (LC-40LE835U)
N DKEYMF733FM14 BW N X MAIN Unit (LC-46LE835U)
N DKEYMF733FM13 BW N X MAIN Unit (LC-52LE835U)
N DKEYMF733FM12 BW N X MAIN Unit (LC-60LE835U)
N DKEYMF733FM04 BV N X MAIN Unit (LC-40LE830U)
N DKEYMF733FM03 BV N X MAIN Unit (LC-46LE830U)
N DKEYMF733FM02 BV N X MAIN Unit (LC-52LE830U)
N DKEYMF733FM01 BV N X MAIN Unit (LC-60LE830U)
N DKEYMF733FM18 N X MAIN Unit (LC-60LE831U)
N DKEYMF733FM10 BV N X MAIN Unit (LC-40LE832U)
N DKEYMF733FM08 BV N X MAIN Unit (LC-46LE832U)
N DKEYMF733FM07 BV N X MAIN Unit (LC-52LE832U)
N DKEYMF733FM06 BV N X MAIN Unit (LC-60LE832U)
N DUNTKF494FM01 AG N X R/C, Operation Unit
N DUNTKF770FM03 AG N X ICON Unit (LC-40/46/52/60LE835U)
N DUNTKF770FM02 AE N X ICON Unit (LC-40/46/52/60LE830U/832U/LC-60LE831U)
N RUNTKA810WJQZ AZ N X WiFi Unit
N RUNTKA811WJQZ AS N X Touch Sensor Unit (LC-40/46/52/60LE835U)
N RUNTKA812WJQZ AN N X Touch Sensor Unit (LC-40/46/52/60LE830U/832U/LC-60LE831U)
N RUNTKA819WJQZ AT N X IR Emitter Unit (LC-40/46/52/60LE835U Only)
! N RUNTKA786WJQZ BM N X POWER/LED Drive Unit (LC-40LE835U/830U/832U)
! N RUNTKA790WJQZ BN N X POWER/LED Drive Unit (LC-46LE835U/830U/832U)
! N RUNTKA794WJQZ BN N X POWER/LED Drive Unit (LC-52LE835U/830U/832U)
! N RUNTKA798WJQZ BP N X POWER/LED Drive Unit (LC-60LE835U/830U/831U/832U)
N RUNTK4909TPZS BV N X LCD Control Unit (LC-40LE835U)
N RUNTK4909TPZW BV N X LCD Control Unit (LC-46LE835U)
N RUNTK4909TPZF BV N X LCD Control Unit (LC-52LE835U)
N RUNTK4909TPZA BV N X LCD Control Unit (LC-60LE835U)
N RUNTK4910TPZE BQ N X LCD Control Unit (LC-40LE830U/832U)
N RUNTK4910TPZC BQ N X LCD Control Unit (LC-46LE830U/832U)
N RUNTK4910TPZB BQ N X LCD Control Unit (LC-52LE830U/832U)
N RUNTK4910TPZZ BQ N X LCD Control Unit (LC-60LE830U/831U/832U)
[2] LCD PANEL MODULE UNIT
N R1LK400D3GW50Z DQ N X 40" LCD Panel Module Unit (LK400D3GW50Z) (LC-40LE835U)
N R1LK460D3GW40Z DQ N X 46" LCD Panel Module Unit (LK460D3GW40Z) (LC-46LE835U)
N R1LK520D3GW40Z EG N X 52" LCD Panel Module Unit (LK520D3GW40Z) (LC-52LE835U)
N R1LK600D3GW40Z EX N X 60" LCD Panel Module Unit (LK600D3GW40Z) (LC-60LE835U)
N R1LK400D3GW80Z DN N X 40" LCD Panel Module Unit (LK400D3GW80Z) (LC-40LE830U/832U)
N R1LK460D3GW80Z DP N X 46" LCD Panel Module Unit (LK460D3GW80Z) (LC-46LE830U/832U)
N R1LK520D3GW80Z EE N X 52" LCD Panel Module Unit (LK520D3GW80Z) (LC-52LE830U/832U)
N R1LK600D3GW30Z EY N X 60" LCD Panel Module Unit (LK600D3GW30Z) (LC-60LE830U/831U/832U)
2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[3] CABINET PARTS (LC-40LE835U/830U/832U)
SP
39 26
36
H G 16 10
3
1 34 PD 11
30 RA 18
UB CI 39 13
1-6 WiFi Unit
MAIN SB
ICON Unit
1-4 Unit 42
1-1 IR 12
1-5 10
R/C, E
H Operation IR Emitter Unit SP 13
1-3 Unit (LC-40LE835U Only) 6
LW
G 1-2 13
TK 17
RA 19
Touch
Sensor
38
Unit 4 35
PL
1-7 23
37 CI TK IR
23
A
UB LC-40LE835U
29 F
Only
9
29 41
8
8 7 47
14 29 10
28
PD
29 15 29 5
5 D
8 8
B PL
F 7 33
E LW 10 8
D 32
LCD POWER/LED
C 22 Control Drive Unit
Unit 29
20 22
21
20
SB
40" LCD
Panel Module Unit
40
46
41
2-2
2 41
27 44
2-4
B
2-1 2-3 41
25
31
24
41
A
43
41 45
3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[3] CABINET PARTS (LC-40LE835U/830U/832U)
1 CCABAC653WJ31 BH N X Front Cabinet Ass'y (LC-40LE835U)
1 CCABAC653WJ32 BD N X Front Cabinet Ass'y (LC-40LE830U)
1 CCABAC653WJ33 BD N X Front Cabinet Ass'y (LC-40LE832U)
1-1 Not Available - N - Front Cabinet
1-2 Not Available - N - R/C Operation Cover
1-3 HDECQB539WJ3A AX N X Front Decoration (LC-40LE835U)
1-3 HDECQB603WJ3A AX N X Front Decoration (LC-40LE830U)
1-3 HDECQB603WJ3B AX N X Front Decoration (LC-40LE832U)
1-4 LHLDWA133WJKZ AC J Wire Holder
1-5 Not Available - N - Sheet
1-6 TLABZC680WJZZ AB N X Quattron 3D Label (LC-40LE835U)
1-6 TLABZC585WJZZ AF J Quattron Label (LC-40LE830U/832U)
1-7 TLABZC778WJZZ AA N X WiFi Label
2 CCABBB885WJ31 BC N X Rear Cabinet Ass'y
2-1 Not Available - N - Rear Cabinet
2-2 HiNDPE029WJSA AF N X Terminal Label (Length)
2-3 HiNDPE031WJSA AE N X Terminal Label (Width)
2-4 HiNDPE034WJSA AD N X Terminal Label (Back)
3 HDECPA090WJZZ AC N X Decoration Sheet (Side)
4 HDECPA091WJZZ AB N X Decoration Sheet (Bottom)
5 LANGKD119WJM1 AH N X Center Angle, x2
6 LANGKD146WJFW AD N X Terminal Angle Bottom
7 LHLDWA138WJKZ AC J Wire Holder, x3
8 LHLDWA175WJUZ AC J Wire Holder, x8
9 LHLDWA176WJUZ AC J Wire Holder, x2
10 LX-BZA207WJF7 AA J Screw, x20
11 PSLDMB748WJFW AH N X Main PWB Shield
12 PSPAZC690WJZZ AC N X Spacer
13 PSPAZC691WJZZ AB N X Spacer, x3
14 PSPAZC702WJKZ AH N X Spacer
15 PZETKA579WJKZ AM N X Insulation Sheet
16 QCNW-L581WJQZ AM N X Connecting Cord (PD:MAIN-POW)
17 QCNW-L587WJQZ AE N X Connecting Cord (PL:MAIN-LCDCTL)
18 QCNW-L617WJQZ AE N X Connecting Cord (SB:MAIN-WOOFER)
19 QCNW-L627WJQZ AS N X Connecting Cord (LW:MAIN-LCDCTL) (LC-40LE835U)
19 QCNW-L718WJQZ N X Connecting Cord (LV:MAIN-LCDCTL) (LC-40LE830U/832U)
20 QCNWN2735TPZZ AD N X Connecting Cord FFC (80P:MDL-CTL), x2
21 QCNWN2736TPZZ AD N X Connecting Cord FFC (64P:MDL-CTL), x2
22 RCORFA061WJZZ AG J Core, x4
23 XBPS830P06WS0 AA J Screw, x9
24 GCOVAC576WJKZ AC J Vesa Hole Cover, x4
25 GCOVAD969WJ3A AC N X AC Cord Cover
26 GCOVAD973WJ3A AD N X Bottom Cover
27 HiNDPE022WJSA AB N X Model Label (LC-40LE835U)
27 HiNDPE053WJSA AB N X Model Label (LC-40LE830U)
27 HiNDPE062WJSA AB N X Model Label (LC-40LE832U)
28 LANGKD123WJM1 AP N X Stand TCON Angle
29 LANGKD127WJFW AA N X Fixing Metal Angle, x8
30 LHLDWA175WJUZ AC J Wire Holder
31 LHLDWA303WJKA AE J Cable Clamp
32 PSPAZC062WJKZ AG J Spacer
! 33 QACCDA084WJPZ AH N X AC Cord
34 QCNW-L582WJQZ AD N X Connecting Cord (RA:KEY-R/C)
35 QCNW-L583WJQZ AF N X Connecting Cord (CI:MAN-EMBLEM)
36 QCNW-L586WJQZ AG N X Connecting Cord (SP:MAIN-SP(L/R))
37 QCNW-L588WJQZ AG N X Connecting Cord (UB:MAIN-WIFI)
38 QCNW-L589WJQZ AR N X Connecting Cord (RC:MAIN-KEY/IR) (LC-40LE835U)
38 QCNW-L721WJQZ AN N X Connecting Cord (RC:MAIN-KEY) (LC-40LE830U/832U)
39 RSP-ZA511WJQZ AR N X Speaker (L/R), x2
40 RSP-ZA513WJQZ AV N X Speaker (Sub Woofer)
41 XBPS830P06WS0 AA J Screw, x21
42 XEBS830P08000 AA J Screw
43 XEBS830P12000 AA J Screw, x5
44 TLABNB037WJZZ AB N X Serial Label (Back)
45 Not Available - N - Serial Label (Side)
46 LX-BZA401WJN1 AB N X Screw, x2
47 PZETKA593WJKZ AE N X Insulation Sheet
4
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[4] CABINET PARTS (LC-46LE835U/830U/832U)
SP 17
39 27
36 PD 11
H G 3
19
1 12
SB
34 14
UB CI 46
1-6 WiFi Unit 11
RA MAIN
39
ICON Unit
1-4 Unit
42 13
1-1 1-5 IR E SP
R/C, 14
H Operation 6
1-3 IR Emitter Unit LW
Unit (LC-46LE835U Only) 14
G 20 18
TK 1-2
RA Touch 38
Sensor 4 35
Unit PL
1-7 37 CI TK IR
(LC-46LE835U
UB Only)
24
A
24
9
30 F
8 9
30 41
30 10
47 29
7
9
15
30 11
30 16 5
8 PD
5
11 9 D
B PL
E 9
F LW 33
D 32
LCD
C 23 Control 30 POWER/LED
Unit Drive Unit
21 23
22 SB
21
C
48
40
46" LCD 41
Panel Module Unit 2-2
2 41 28
44
2-4
B 31
2-1 2-3 41
26
25
41
A
43
41 45
5
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[4] CABINET PARTS (LC-46LE835U/830U/832U)
1 CCABAC654WJ31 BK N X Front Cabinet Ass'y (LC-46LE835U)
1 CCABAC654WJ32 BF N X Front Cabinet Ass'y (LC-46LE830U)
1 CCABAC654WJ33 BF N X Front Cabinet Ass'y (LC-46LE832U)
1-1 Not Available - N - Front Cabinet
1-2 Not Available - N - R/C Operation Cover
1-3 HDECQB540WJ3A AX N X Front Decoration (LC-46LE835U)
1-3 HDECQB604WJ3A AX N X Front Decoration (LC-46LE830U)
1-3 HDECQB604WJ3B AX N X Front Decoration (LC-46LE832U)
1-4 LHLDWA133WJKZ AC J Wire Holder
1-5 Not Available - N - Sheet
1-6 TLABZC680WJZZ AB N X Quattron 3D Label
1-6 TLABZC585WJZZ AF J Quattron Label
1-7 TLABZC778WJZZ AA N X WiFi Label
2 CCABBB886WJ31 BD N X Rear Cabinet Ass'y
2-1 Not Available - N - Rear Cabinet
2-2 HiNDPE029WJSA AF N X Terminal Label (Length)
2-3 HiNDPE031WJSA AE N X Terminal Label (Width)
2-4 HiNDPE034WJSA AD N X Terminal Label (Back)
3 HDECPA090WJZZ AC N X Decoration Sheet (Side)
4 HDECPA091WJZZ AB N X Decoration Sheet (Bottom)
5 LANGKD120WJM1 AK N X Center Angle, x2
6 LANGKD146WJFW AD N X Terminal Angle Bottom
7 LHLDWA133WJKZ AC J Wire Holder, x2
8 LHLDWA138WJKZ AC J Wire Holder, x2
9 LHLDWA175WJUZ AC J Wire Holder, x9
10 LHLDWA176WJUZ AC J Wire Holder
11 LX-BZA207WJF7 AA J Screw, x20
12 PSLDMB748WJFW AH N X Main PWB Shield
13 PSPAZC690WJZZ AC N X Spacer
14 PSPAZC691WJZZ AB N X Spacer, x3
15 PSPAZC702WJKZ AH N X Spacer
16 PZETKA580WJKZ AN N X Insulator Sheet
17 QCNW-L590WJQZ AN N X Connecting Cord (PD:MAIN-POW)
18 QCNW-L596WJQZ AE N X Connecting Cord (PL:MAIN-LCDCTL)
19 QCNW-L618WJQZ AF N X Connecting Cord (SB:MAIN-WOOFER)
20 QCNW-L628WJQZ AR N X Connecting Cord (LW:MAIN-LCDCTL) (LC-46LE835U)
20 QCNW-L719WJQZ N X Connecting Cord (LV:MAIN-LCDCTL) (LC-46LE830U/832U)
21 QCNWN2733TPZZ AE N X Connecting Cord (80P:MDL-CTL), x2
22 QCNWN2734TPZZ AE N X Connecting Cord (64P:MDL-CTL), x2
23 RCORFA061WJZZ AG J Core, x4
24 XBPS830P06WS0 AA J Screw, x12
25 GCOVAC576WJKZ AC J Vesa Hole Cover, x4
26 GCOVAD969WJ3A AC N X AC Cord Cover
27 GCOVAD973WJ3A AD N X Bottom Cover
28 HiNDPE023WJSA AB N X Model Label (LC-46LE835U)
28 HiNDPE055WJSA AB N X Model Label (LC-46LE830U)
28 HiNDPE065WJSA AB N X Model Label (LC-46LE832U)
29 LANGKD124WJM1 AS N X Stand TCON Angle
30 LANGKD127WJFW AA N X Fixing Metal Angle, x9
31 LHLDWA303WJKA AE J Cable Clamp
32 PSPAZC062WJKZ AG J Spacer
! 33 QACCDA084WJPZ AH N X AC Cord
34 QCNW-L582WJQZ AD N X Connecting Cord (RA:KEY-R/C)
35 QCNW-L592WJQZ AF N X Connecting Cord (CI:MAN-EMBLEM)
36 QCNW-L595WJQZ AG N X Connecting Cord (SP:MAIN-SP(L/R))
37 QCNW-L597WJQZ AH N X Connecting Cord (UB:MAIN-WIFI)
38 QCNW-L598WJQZ AT N X Connecting Cord (RC:MAIN-KEY/IR) (LC-40LE835U)
38 QCNW-L722WJQZ AP N X Connecting Cord (RC:MAIN-KEY) (LC-40LE830U/832U)
39 RSP-ZA511WJQZ AR N X Speaker (L/R), x2
40 RSP-ZA513WJQZ AV N X Speaker (Sub Woofer)
41 XBPS830P06WS0 AA J Screw, x21
42 XEBS830P08000 AA J Screw
43 XEBS830P12000 AA J Screw, x5
44 TLABNB037WJZZ AB N X Serial Label (Back)
45 Not Available - N - Serial Label (Side)
46 LHLDWA175WJUZ AC J Wire Holder
47 PZETKA605WJKZ AG N X Insulation Sheet
48 LX-BZA401WJN1 AB N X Screw, x2
6
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[5] CABINET PARTS (LC-52LE835U/830U/832U)
SP 17
39 11
27 3
37 PD
12
H G
19 14
1
35 MAIN SB
UB CI 46 RA 39 Unit
WiFi Unit 11
1-6 13
ICON
1-1 Unit E SP 14
1-4 42
1-5 IR 6 LW
R/C, 14
H Operation IR Emiter Unit 20 18
Unit (LC-52LE835U Only)
G TK 1-2 38
RA 4 36
Touch PL
Sensor
Unit 34 CI TK IR
24
1-7
UB LC-52LE835U Only
1-3 24
A
30 F
30 10
41
9
9 30 8
47 29
9
30 15 30
5
8 16 5 11
B 11
E PL 9
LW 9 PD
F
32 30
D D
LCD
C 21 Control
22
Unit
21
23 POWER/LED 33
Drive Unit
SB
C
52" LCD
Panel Module Unit
40
41 48
41 2-2 28 44
2
2-4
B 41
2-3 41
26
2-1
31
41
A 43
25
41
45
7
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[5] CABINET PARTS (LC-52LE835U/830U/832U)
1 CCABAC655WJ31 BM N X Front Cabinet Ass'y (LC-52LE835U)
1 CCABAC655WJ32 BG N X Front Cabinet Ass'y (LC-52LE830U)
1 CCABAC655WJ33 BG N X Front Cabinet Ass'y (LC-52LE832U)
1-1 Not Available - N - Front Cabinet
1-2 Not Available - N - R/C Operation Cover
1-3 HDECQB541WJ3A AY N X Front Decoration(LC-52LE835U)
1-3 HDECQB605WJ3A AY N X Front Decoration(LC-52LE830U)
1-3 HDECQB605WJ3B AY N X Front Decoration(LC-52LE832U)
1-4 LHLDWA133WJKZ AC J Wire Holder
1-5 Not Available - N - Sheet
1-6 TLABZC680WJZZ AB N X Quattron 3D Label (LC-52LE835U)
1-6 TLABZC585WJZZ AF J Quattron Label (LC-52LE830U/832U)
1-7 TLABZC778WJZZ AA N X WiFi Label
2 CCABBB887WJ31 BF N X Rear Cabinet Ass'y
2-1 Not Available - N - Rear Cabinet
2-2 HiNDPE031WJSA AE N X Terminal Label (Width)
2-3 HiNDPE034WJSA AD N X Terminal Label (Back)
2-4 HiNDPE116WJSA AF N X Terminal Label (Length)
3 HDECPA090WJZZ AC N X Decoration Sheet (Side)
4 HDECPA091WJZZ AB N X Decoration Sheet (Bottom)
5 LANGKD121WJM1 AL N X Center Angle, x2
6 LANGKD146WJFW AD N X Terminal Angle Bottom
8 LHLDWA138WJKZ AC J Wire Holder, x2
9 LHLDWA175WJUZ AC J Wire Holder, x8
10 LHLDWA176WJUZ AC J Wire Holder
11 LX-BZA207WJF7 AA J Screw, x20
12 PSLDMB748WJFW AH N X Main PWB Shield
13 PSPAZC690WJZZ AC N X Spacer
14 PSPAZC691WJZZ AB N X Spacer, x3
15 PSPAZC702WJKZ AH N X Spacer
16 PZETKA580WJKZ AN N X Insulator Sheet
17 QCNW-L590WJQZ AN N X Connecting Cord (PD:MAIN-POW)
18 QCNW-L596WJQZ AE N X Connecting Cord (PL:MAIN-LCDCTL)
19 QCNW-L618WJQZ AF N X Connecting Cord (SB:MAIN-WOOFER)
20 QCNW-L628WJQZ AR N X Connecting Cord (LW:MAIN-LCDCTL) (LC-52LE835U)
20 QCNW-L719WJQZ N X Connecting Cord (LV:MAIN-LCDCTL) (LC-52LE830U/832U)
21 QCNWN2733TPZZ AE N X Connecting Cord (80P:MDL-CTL), x2
22 QCNWN2734TPZZ AE N X Connecting Cord (64P:MDL-CTL), x2
23 RCORFA061WJZZ AG J Core, x4
24 XBPS830P06WS0 AA J Screw, x12
25 GCOVAC576WJKZ AC J Vesa Hole Cover, x4
26 GCOVAD969WJ3A AC N X AC Cord Cover
27 GCOVAD973WJ3A AD N X Bottom Cover
28 HiNDPE024WJSA AB N X Model Label (LC-52LE835U)
28 HiNDPE057WJSA AB N X Model Label (LC-52LE830U)
28 HiNDPE068WJSA AB N X Model Label (LC-52LE832U)
29 LANGKD124WJM1 AS N X Fixing Metal Angle
30 LANGKD127WJFW AA N X Fixing Metal Angle, x12
31 LHLDWA303WJKA AE J Cable Clamp
32 PSPAZC062WJKZ AG J Spacer
! 33 QACCDA084WJPZ AH N X AC Cord
34 QCNW-L597WJQZ AH N X Connecting Cord (UB:MAIN-WIFI)
35 QCNW-L600WJQZ AE N X Connecting Cord (RA:KEY-R/C)
36 QCNW-L601WJQZ AE N X Connecting Cord (CI:MAN-EMBLEM)
37 QCNW-L604WJQZ AG N X Connecting Cord (SP:MAIN-SP(L/R))
38 QCNW-L607WJQZ AR N X Connecting Cord (RC:MAIN-KEY/IR) (LC-52LE835U)
38 QCNW-L723WJQZ AP N X Connecting Cord (RC:MAIN-KEY) (LC-52LE830U/832U)
39 RSP-ZA512WJQZ AV N X Speaker (L/R), x2
40 RSP-ZA513WJQZ AV N X Speaker (Sub Woofer)
41 XBPS830P06WS0 AA J Screw, x24
42 XEBS830P08000 AA J Screw
43 XEBS830P12000 AA J Screw, x7
44 TLABNB037WJZZ AB N X Serial Label (Back)
45 Not Available - N - Serial Label (Side)
46 LHLDWA175WJUZ AC J Wire Holder
47 PZETKA605WJKZ AG N X Insulation Sheet
48 LX-BZA401WJN1 AB N X Screw, x3
8
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[6] CABINET PARTS (LC-60LE835U/830U/831U/832U)
SP
18
40
37 PD
H
1 11
19
12
1-7
UB CI 31 SB 14
WiFi Unit 35
40 13
ICON RA
1-5 43 MAIN 5
Unit
1-1 1-4 Unit
IR
11
H R/C, 14
IR Emitter Unit E SP
G 1-6 Operation (LC-60LE835U Only)
1-3 8
Unit LW
TK 1-2 14
RA 20 17
Touch
Sensor
6 39
Unit 36
PL
1-8
38 CI TK IR
LC-52LE835U Only
UB
24 27
24 42
A 44
F 42
G
30
42 11
30 10 10 PD
29
30
15
7 D
10
9 7
16
B 11
F PL
10 POWER/LED 34
LW 30
E Drive Unit
33
D
LCD SB
C 21 22 Control
Unit
21 C
23
41
42
60" LCD 47
Panel Module Unit 28 45
2 42 2-3
2-4
42 2-2
B
2-1 42
25 26
32
42
A 42
44
46
9
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[6] CABINET PARTS (LC-60LE835U/830U/831U/832U)
1 CCABAC656WJ31 BQ N X Front Cabinet Ass'y (LC-60LE835U)
1 CCABAC656WJ32 BM N X Front Cabinet Ass'y (LC-60LE830U)
1 CCABAC656WJ34 N X Front Cabinet Ass'y (LC-60LE831U)
1 CCABAC656WJ33 BK N X Front Cabinet Ass'y (LC-60LE832U)
1-1 Not Available - N - Front Cabinet
1-2 Not Available - N - R/C Operation Cover
1-3 HDECQB542WJ3A AZ N X Front Decoration (LC-60LE835U)
1-3 HDECQB606WJ3A AZ N X Front Decoration (LC-60LE830U)
1-3 HDECQB606WJ3C N X Front Decoration (LC-60LE831U)
1-3 HDECQB606WJ3B AZ N X Front Decoration (LC-60LE832U)
1-4 LHLDWA133WJKZ AC J Wire Holder
1-5 LHLDWA138WJKZ AC J Wire Holder
1-6 Not Available - N - Sheet
1-7 TLABZC635WJZZ AF N X Quattron 3D Label (LC-60LE835U)
1-7 TLABZC586WJZZ AF J Quattron Label (LC-60LE830U/832U)
1-7 TLABZC810WJZZ N X Quattron Label (LC-60LE831U)
1-8 TLABZC778WJZZ AA N X WiFi Label
2 CCABBB888WJ31 BM N X Rear Cabinet Ass'y
2-1 Not Available - N - Rear Cabinet
2-2 HiNDPE031WJSA AE N X Terminal Label (Width)
2-3 HiNDPE034WJSA AD N X Terminal Label (Back)
2-4 HiNDPE116WJSA AF N X Terminal Label (Length)
5 HDECPA090WJZZ AC N X Decoration Sheet (Side)
6 HDECPA091WJZZ AB N X Decoration Sheet (Bottom)
7 LANGKD122WJM1 AM N X Center Angle, x2
8 LANGKD146WJFW AD N X Terminal Angle Bottom
9 LHLDWA138WJKZ AC J Wire Holder, x4
10 LHLDWA175WJUZ AC J Wire Holder, x5
11 LX-BZA207WJF7 AA J Screw, x20
12 PSLDMB748WJFW AH N X Main PWB Shield
13 PSPAZC690WJZZ AC N X Spacer
14 PSPAZC691WJZZ AB N X Spacer, x3
15 PSPAZC702WJKZ AH N X Spacer
16 PZETKA581WJKZ AP N X Insulator Sheet
17 QCNW-L587WJQZ AE N X Connecting Cord (PL:MAIN-LCDCTL)
18 QCNW-L608WJQZ AN N X Connecting Cord (PD:MAIN-POW)
19 QCNW-L620WJQZ AE N X Connecting Cord (SB:MAIN-WOOFER)
20 QCNW-L629WJQZ AS N X Connecting Cord (LW:MAIN-LCDCTL) (LC-60LE835U)
20 QCNW-L720WJQZ N X Connecting Cord (LW:MAIN-LCDCTL) (LC-60LE830U/831U/832U)
21 QCNWN2731TPZZ AE N X Connecting Cord (80P:MDL-CTL), x2
22 QCNWN2732TPZZ AE N X Connecting Cord (64P:MDL-CTL), x2
23 RCORFA061WJZZ AG J Core, x4
24 XBPS830P06WS0 AA J Screw, x16
25 GCOVAC576WJKZ AC J Vesa Hole Cover, x4
26 GCOVAD969WJ3A AC N X AC Cord Cover
27 GCOVAD976WJ3A AM N X Bottom Cover
28 HiNDPE025WJSA AB N X Model Label (LC-60LE835U)
28 HiNDPE059WJSA AB N X Model Label (LC-60LE830U)
28 HiNDPE222WJSA N X Model Label (LC-60LE831U)
28 HiNDPE071WJSA AB N X Model Label (LC-60LE832U)
29 LANGKD126WJM1 AQ N X Fixing Metal Angle
30 LANGKD127WJFW AA N X Fixing Metal Angle, x14
31 LHLDWA175WJUZ AC J Wire Holder
32 LHLDWA303WJKA AE J Cable Clamp
33 PSPAZC062WJKZ AG J Spacer
! 34 QACCDA084WJPZ AH N X AC Cord
35 QCNW-L600WJQZ AE N X Connecting Cord (RA:KEY-R/C)
36 QCNW-L610WJQZ AE N X Connecting Cord (CI:MAN-EMBLEM)
37 QCNW-L613WJQZ AG N X Connecting Cord (SP:MAIN-SP(L/R))
38 QCNW-L615WJQZ AH N X Connecting Cord (UB:MAIN-WIFI)
39 QCNW-L616WJQZ AS N X Connecting Cord (RC:MAIN-KEY/IR) (LC-60LE835U)
39 QCNW-L724WJQZ AQ N X Connecting Cord (RC:MAIN-KEY) (LC-60LE830U/831U/832U)
40 RSP-ZA512WJQZ AV N X Speaker (L/R), x2
41 RSP-ZA513WJQZ AV N X Speaker (Sub Woofer)
42 XBPS830P06WS0 AA J Screw, x40
43 XEBS830P08000 AA J Screw
44 XEBS830P12000 AA J Screw, x7
45 TLABNB037WJZZ AB N X Serial Label (Back)
46 Not Available - N - Serial Label (Side)
47 LX-BZA401WJN1 AB N X Screw, x3
10
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[7] SUPPLIED ACCESSORIES/PACKING PARTS (LC-40LE835U/830U/832U)
X5
X10
X1 X2 X3
“AAA” size battery
Remote control
X8
X4 Operation manual
X9
Cable Clamp X6 Enquete Card X7 Guarantee Card
Connection guide
S5
X2
S8
X4
X10
S6 S4
X1 S4
S7
X5 X6
S9 X7
X3 X8
X9
S1
S3
S3
S3
FRONT
S2
S10
S10
11
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[7] SUPPLIED ACCESSORIES/PACKING PARTS (LC-40LE835U/830U/832U)
X1 CANGKD135WJ01 AS N X Stand Support Ass'y (LC-40LE835U/830U/832U)
X2 CDAi-A720WJ01 BD N X Stand Base Ass'y (LC-40LE835U)
X2 CDAi-A720WJ02 BD N X Stand Base Ass'y (LC-40LE830U/832U)
X3 CSAKKA010WJ01 AD N X Stand Screw Ass'y (LC-40LE835U/830U/832U)
X4 LHLDWA303WJKA AE J Cable Clamp
X5 RRMCGA936WJSA AR N X Remote Control (LC-40LE835U)
X5 RRMCGA935WJSA AQ N X Remote Control (LC-40LE830U/832U)
X6 TCADEA243WJZZ AB N X Enquete Card
X7 Not Available - N - Guarantee Card
X8 TiNS-F027WJZZ AN N X Operation Manual (LC-40LE835U)
X8 TiNS-F030WJZZ AN N X Operation Manual (LC-40LE830U)
X8 TiNS-F031WJZZ AP N X Operation Manual (LC-40LE832U)
X9 TMAN-A043WJZZ AB N X Connection Guide
X10 Not Available - - AAA size battery
S1 SPAKCF954WJZZ - N - Packing Case (LC-40LE835U) (NOT REPLACEMENT ITEM)
S1 SPAKCF984WJZZ - N - Packing Case (LC-40LE830U) (NOT REPLACEMENT ITEM)
S1 SPAKCF993WJZZ - N - Packing Case (LC-40LE832U) (NOT REPLACEMENT ITEM)
S2 SPAKPB219WJZZ - N - Wrapping Paper (NOT REPLACEMENT ITEM)
S3 SPAKXD151WJZZ - N - Packing Add. (Top) (NOT REPLACEMENT ITEM)
S4 SPAKXD235WJZZ - N - Packing Add. (Bottom) (NOT REPLACEMENT ITEM)
S5 SPAKPB688WJZZ - N - Wrapping Paper (Stand Base) (NOT REPLACEMENT ITEM)
S6 SPAKPB689WJZZ - N - Wrapping Paper (Support), x2 (NOT REPLACEMENT ITEM)
S7 SSAKA0101GJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S8 SSAKAA032WJZZ - - Polyethylene Bag (NOT REPLACEMENT ITEM)
S9 SSAKKA010WJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S10 TLABKA009WJZZ - N - Case No. Label (NOT REPLACEMENT ITEM)
12
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[8] SUPPLIED ACCESSORIES/PACKING PARTS (LC-46LE835U/830U/832U)
X5
X10
X1 X2 X3
“AAA” size battery
Remote control
X8
X4 Operation manual
X9
Cable Clamp X6 Enquete Card X7 Guarantee Card
Connection guide
X5 S3
S9 S10 FRONT
X3 X6
X7
S11 X8
X4 X9
X10
S4 S6
S7 X2
S8
X1
S4
S5
S4
S5
S5
S1
S2
S12
S12
13
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[8] SUPPLIED ACCESSORIES/PACKING PARTS (LC-46LE835U/830U/832U)
X1 CANGKD136WJ01 AU N X Stand Support Ass'y (LC-46LE835U/830U/832U)
X2 CDAi-A721WJ01 BF N X Stand Base Ass'y (LC-46LE835U)
X2 CDAi-A721WJ02 BF N X Stand Base Ass'y (LC-46LE830U/832U)
X3 CX-BZA399WJ01 AF N X Stand Screw Ass'y (LC-46LE835U/830U/832U)
X4 LHLDWA303WJKA AE J Cable Clamp
X5 RRMCGA936WJSA AR N X Remote Control (LC-46LE835U)
X5 RRMCGA935WJSA AQ N X Remote Control (LC-46LE830U/832U)
X6 TCADEA243WJZZ AB N X Enquete Card
X7 Not Available - N - Guarantee Card
X8 TiNS-F027WJZZ AN N X Operation Manual (LC-46LE835U)
X8 TiNS-F030WJZZ AN N X Operation Manual (LC-46LE830U)
X8 TiNS-F031WJZZ AP N X Operation Manual (LC-46LE832U)
X9 TMAN-A043WJZZ AB N X Connection Guide
X10 Not Available - - AAA size battery
S1 SPAKCF955WJZZ - N - Packing Case (LC-46LE835U) (NOT REPLACEMENT ITEM)
S1 SPAKCF986WJZZ - N - Packing Case (LC-46LE830U) (NOT REPLACEMENT ITEM)
S1 SPAKCF996WJZZ - N - Packing Case (LC-46LE832U) (NOT REPLACEMENT ITEM)
S2 SPAKCF956WJZZ - N - Bottom Case (NOT REPLACEMENT ITEM)
S3 SPAKPA999WJZZ - N - Wrapping Paper (NOT REPLACEMENT ITEM)
S4 SPAKXD152WJZZ - N - Packing Add. (Top) (NOT REPLACEMENT ITEM)
S5 SPAKXD239WJZZ - N - Packing Add. (Bottom) (NOT REPLACEMENT ITEM)
S6 SPAKFC109WJZZ - N - Polyethylene Bag (Stand) (LX-46LE835U) (NOT REPLACEMENT ITEM)
S6 SPAKFC116WJZZ - N - Polyethylene Bag (Stand) (LX-46LE830U/832U) (NOT REPLACEMENT ITEM)
S7 SPAKFC110WJZZ - N - Polyethylene Bag (Support) (NOT REPLACEMENT ITEM)
S8 SPAKFC111WJZZ - N - Polyethylene Bag (Angle) (NOT REPLACEMENT ITEM)
S9 SPAKFC112WJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S10 SSAKA0101GJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S11 SSAKAA032WJZZ - - Polyethylene Bag (NOT REPLACEMENT ITEM)
S12 TLABKA009WJZZ - N - Case No. Label (NOT REPLACEMENT ITEM)
14
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[9] SUPPLIED ACCESSORIES/PACKING PARTS (LC-52LE835U/830U/832U)
X5
X10
X1 X2 X3
“AAA” size battery
Remote control
X8
X4 Operation manual
X9
Cable Clamp X6 Enquete Card X7 Guarantee Card
Connection guide
X5
S9 S10
X3 X6
X7 S3
S11 X8
X4 X9 FRONT
X10
S4
S7
S8
X1
S4
S6
X2
S4
S5
S5
S5
S1
S2
S12
S12
15
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[9] SUPPLIED ACCESSORIES/PACKING PARTS (LC-52LE835U/830U/832U)
X1 CANGKD136WJ01 AU N X Stand Support Ass'y (LC-52LE835U/830U/832U)
X2 CDAi-A721WJ01 BF N X Stand Base Ass'y (LC-52LE835U)
X2 CDAi-A721WJ02 BF N X Stand Base Ass'y (LC-52LE830U/832U)
X3 CX-BZA399WJ01 AF N X Stand Screw Ass'y (LC-52LE835U/830U/832U)
X4 LHLDWA303WJKA AE J Cable Clamp
X5 RRMCGA936WJSA AR N X Remote Control (LC-52LE835U)
X5 RRMCGA935WJSA AQ N X Remote Control (LC-52LE830U/832U)
X6 TCADEA243WJZZ AB N X Enquete Card
X7 Not Available - N - Guarantee Card
X8 TiNS-F027WJZZ AN N X Operation Manual (LC-52LE835U)
X8 TiNS-F030WJZZ AN N X Operation Manual (LC-52LE830U)
X8 TiNS-F031WJZZ AP N X Operation Manual (LC-52LE832U)
X9 TMAN-A043WJZZ AB N X Connection Guide
X10 Not Available - - AAA size battery
S1 SPAKCF957WJZZ - N - Packing Case (LC-52LE835U) (NOT REPLACEMENT ITEM)
S1 SPAKCF988WJZZ - N - Packing Case (LC-52LE830U) (NOT REPLACEMENT ITEM)
S1 SPAKCF999WJZZ - N - Packing Case (LC-52LE832U) (NOT REPLACEMENT ITEM)
S2 SPAKCF958WJZZ - N - Bottom Case (NOT REPLACEMENT ITEM)
S3 SPAKPA992WJZZ - N - Wrapping Paper (NOT REPLACEMENT ITEM)
S4 SPAKXD153WJZZ - N - Packing Add. (Top) (NOT REPLACEMENT ITEM)
S5 SPAKXD243WJZZ - N - Packing Add. (Bottom) (NOT REPLACEMENT ITEM)
S6 SPAKFC109WJZZ - N - Polyethylene Bag (Stand) (LC-52LE835U) (NOT REPLACEMENT ITEM)
S6 SPAKFC116WJZZ - N - Polyethylene Bag (Stand) (LC-52LE830U/832U) (NOT REPLACEMENT ITEM)
S7 SPAKFC110WJZZ - N - Polyethylene Bag (Support) (NOT REPLACEMENT ITEM)
S8 SPAKFC111WJZZ - N - Polyethylene Bag (Angle) (NOT REPLACEMENT ITEM)
S9 SPAKFC112WJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S10 SSAKA0101GJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S11 SSAKAA032WJZZ - - Polyethylene Bag (NOT REPLACEMENT ITEM)
S12 TLABKA009WJZZ - N - Case No. Label (NOT REPLACEMENT ITEM)
16
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[10] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE835U/830U/831U/832U)
X5
X10
X1 X2 X3
“AAA” size battery
Remote control
X4
X8 X9
Cable Clamp X6 Enquete Card X7 Guarantee Card
Operation manual Connection guide
X5
S10
X3
S9
S8
X4 X6
X10 X7
S4
X8
X9
S4
S6
X2
S4
S7
S5 X1
S5
S1
S5
S2
S5
S3
FRONT
S11
S5
S11
17
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK DELIVERY
[10] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE835U/830U/831U/832U)
X1 CANGKD137WJ01 BB N X Stand Support Ass'y (LC-60LE835U/830U/831U/832U)
X2 CDAi-A722WJ01 BH N X Stand Base Ass'y (LC-60LE835U)
X2 CDAi-A722WJ02 BG N X Stand Base Ass'y (LC-60LE830U/831U/832U)
X3 CSAKKA010WJ02 AD N X Stand Screw Ass'y (LC-60LE835U/830U/831U/832U)
X4 LHLDWA303WJKA AE J Cable Clamp
X5 RRMCGA936WJSA AR N X Remote Control (LC-60LE835U)
X5 RRMCGA935WJSA AQ N X Remote Control (LC-60LE830U/831U/832U)
X6 TCADEA243WJZZ AB N X Enquete Card
X7 Not Available - N - Guarantee Card
X8 TiNS-F027WJZZ AN N X Operation Manual (LC-60LE835U)
X8 TiNS-F030WJZZ AN N X Operation Manual (LC-60LE830U)
X8 TiNS-F098WJZZ N X Operation Manual (LC-60LE831U)
X8 TiNS-F031WJZZ AP N X Operation Manual (LC-60LE832U)
X9 TMAN-A043WJZZ AB N X Connection Guide
X10 Not Available - - AAA size battery
S1 SPAKCF959WJZZ - N - Packing Case (LC-60LE835U) (NOT REPLACEMENT ITEM)
S1 SPAKCF990WJZZ - N - Packing Case (LC-60LE830U) (NOT REPLACEMENT ITEM)
S1 SPAKCG347WJZZ - N - Packing Case (LC-60LE831U) (NOT REPLACEMENT ITEM)
S1 SPAKCG003WJZZ - N - Packing Case (LC-60LE832U) (NOT REPLACEMENT ITEM)
S2 SPAKCF960WJZZ - N - Bottom Case (NOT REPLACEMENT ITEM)
S3 SPAKPB427WJZZ - N - Wrapping Paper (NOT REPLACEMENT ITEM)
S4 SPAKXD154WJZZ - N - Packing Add. (Top) (NOT REPLACEMENT ITEM)
S5 SPAKXD247WJZZ - N - Packing Add. (Bottom) (NOT REPLACEMENT ITEM)
S6 SPAKPB694WJZZ - N - Polyethylene Bag (Stand Base) (NOT REPLACEMENT ITEM)
S7 SPAKPB695WJZZ - N - Polyethylene Bag (Support), x2 (NOT REPLACEMENT ITEM)
S8 SSAKA0101GJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S9 SSAKAA032WJZZ - - Polyethylene Bag (NOT REPLACEMENT ITEM)
S10 SSAKKA010WJZZ - N - Polyethylene Bag (NOT REPLACEMENT ITEM)
S11 TLABKA009WJZZ - N - Case No. Label (NOT REPLACEMENT ITEM)
[11] SERVICE JIGS (USE FOR SERVICING)
N QCNW-C222WJQZ AW J Connecting Cord L=1000mm 80pin LCD Control Unit to LCD Panel Unit, x2
Connecting Cord L=1000mm 64pin LCD Control Unit to LCD Panel Unit, x2 (LC-40/46/
N QCNW-L214WJQZ AV J
52/60LE835U Only)
N QCNW-F676WJQZ BH J Connecting Cord L=1000mm 41pin Main to LCD Control Unit (LW)
N QCNW-G405WJQZ AP J Connecting Cord L=1000mm 4pin Main to LCD Control Unit (PL)
N QCNW-L795WJQZ J Connecting Cord L=1000mm 24pin Main to POWER/LED Drive Unit (PD)
18
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
COPYRIGHT © 2011 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Jan. 2011 CS Promotion Center
SH. DS Yaita,Tochigi 329-2193, Japan
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
SERVICE MANUAL
No. S21M960LE835U
LCD COLOR TELEVISION
PWB Unit Edition
LC-60LE831U
LC-40/46/52/60LE835U
LC-40/46/52/60LE830U
MODELS LC-40/46/52/60LE832U
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-
inal condition and only parts identical to those specified should be used.
CONTENTS
OUTLINE CHAPTER 2. SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC
CHAPTER 1. PRINTED WIRING BOARD DIAGRAM......................................................2-1
ASSEMBLIES [2] SCHEMATIC DIAGRAM ................................2-2
[1] MAIN Unit....................................................... 1-1
[2] R/C, Operation Unit........................................ 1-5 Parts Guide
[3] ICON Unit....................................................... 1-6
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
OUTLINE
LC-40LE830U
Service Manual
• We inform you that service parts in the PWB Unit.
Unit
Model Name Unit Name Description
LC-40LE835U DKEYMF733FM16 MAIN Unit
LC-46LE835U DKEYMF733FM14 MAIN Unit
LC-52LE835U DKEYMF733FM13 MAIN Unit
LC-60LE835U DKEYMF733FM12 MAIN Unit
LC-40LE830U DKEYMF733FM04 MAIN Unit
LC-46LE830U DKEYMF733FM03 MAIN Unit
LC-52LE830U DKEYMF733FM02 MAIN Unit
LC-60LE830U DKEYMF733FM01 MAIN Unit
LC-60LE831U DKEYMF733FM18 MAIN Unit
LC-40LE832U DKEYMF733FM10 MAIN Unit
LC-46LE832U DKEYMF733FM08 MAIN Unit
LC-52LE832U DKEYMF733FM07 MAIN Unit
LC-60LE832U DKEYMF733FM06 MAIN Unit
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U DUNTKF494FM01 R/C, Operation Unit
LC-40/46/52/60LE835U DUNTKF770FM03 ICON Unit
LC-40/46/52/60LE830U/832U/LC-60LE831U DUNTKF770FM02 ICON Unit
NOTE: *1 Replace MAIN PWB Units (DKEYMF733FM**) in case of IC8401, IC3303 or IC8455 failure.
i
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 1. PRINTED WIRING BOARD ASSEMBLIES
LC-40LE830U
Service Manual
[1] MAIN Unit
MAIN Unit (Side-A)
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1–1
1–2
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
FB2019
FB2022
R2068
P9501 P2007 P2006 P2001 P2004
P2601 P2604
FB2006
C2794
R2021 P2605 P2703 P2701
VA9507 VA9508 FB2008 C2007 C2004 C2005
FB2009
Q2009
R2001
C2022
FB2010
FB2004
FB2007
R2024
FB2018
FB2017
FB2021
FB2020
FB2015
C2024
C2025
L9502 Q2008
C2003
R2015
R2014
R2016
R2010
R2072
R2023
R2048
R2003
R2006
L2601 L2602 L2603 FB2617
R2012 C2001 C2002
FB2611
FB2603
FB2606
FB2607
FB2609
FB2621
FB2622
R2011 R2027
R2728
R2725
R569
L2606 L2604 L2605 C2711
FB2612
FB2613
L2607
L2608
L2609
L2610
Q502
C603 R2726
R2601
R532
C600
VA507
R2654
R2763
R2765
FB2704
FB2705
C2748
C2738
C2718
C2719
C2735
C2747
R2604
R2603
P2002
FL509
FB539
R571 FB2706 C2744 C2745 FB2703
C542
R2607
C543
R518
IC2702
D518
R2608
J9503
P2602
VA9504 VA9503
R647 R2008 R2009
C2728
C2726
R2030
R657
R656
P2003
L9504
D522 FB548
L2704
L2702
L2701
L2703
R2769
D519 C611 C2732 R2742
R2733
R2779
R2741
R2734
R2756
R2752
C615 P2606
R2034
R2033
R2032
X2001
R2738 R2735
R2025 R2026
B
C614
R2745
R670
C2010
C612
IC510 R2036
R2730
R2729
R2732
Q509
R2037 C2716
R2039
C2011
C2013 R2041 R2038
C2720
C2721
C613
L2705
L2706
R2040
L502
R641
R535 C517 R624 D523 D521 R2045
R567
C538
C609 C610
D503
D505
FL508
FB538
C533
D504
C503
R530
C9519
R568
C539
VA506
FL2001
IC507
R2046
FB508
IC2001 IC2703
R564
C532
C599
FB501
C511
R504
C591
R565 FB517 FB518 FB523
C2012 C2014 R2044
R2043
R613
R508
C586
R516 C562 C584 C580 R2042
R2716
R2717
R2718
R2719
R2720
R664
C583 R665
C2731
C2729
VA501 VA502
FB525
IC9504
C585
C9511
D524 R2013 R2056 R2049 R2740
R2736
R2754
R2758
R2771
R2737
R2746
R2747
R2070 C2733
R632 R2743
D526
R609
R2749
C588 IC506 Q2001
R2071
R2051 R2060
R2069
L504
D2004
IC2006
C2019
Q2006
IC2701
J9504
P2702
R608 R2063 R2710
C590
VA9506 VA9505
R2707
L9501
FB527 R2706
Q2007
R2062
D525
R3511
R3531
C
R3510
R3530
R9515 TH2001
C3513
R9556 R2031
D8457
R9516 R3348 R2703
R3509
R618
C9561
FL3504
R2702
C2782
C9520 R3442 IC8451
R8468
R9509 C2701 X2701
R668 SC8452
IC8454
C8457
R3508
IC9505
D8454
C8469
R3518
R3519
R669
R3512
R9514 R8454 R8473 IC3501 IC3502 C3511
C8468
D512
R9512
R3507
R667
R9517
R9513
R666
R9521
R9518 R3516
R3515
C9558
R9520
C9555 R9528 R9523
C9515
R9510
C9517 FB535 R3514
C9552
R3302 R3301
C595
R3513
R507
C9557
FL503
X9502
C9556 D9502
R615
FB534 P3301
R8459
C594
R506
P9603
D
C9509 FL502
C9508 R3532
R8414
R9502
R9504
R3304
FB533 R8451
C593
R505
R3506
T9501
R8455 R3305 R8458 R3536 R3537 R3535 R3534
R3306 C3317
R3545
FL501
R9501
R9503
D3302
R8415
IC509
C9507
C9506 FB504
R3541
R654
R635
D507
FB3303
D1105 R3542
R636
FB505 R625 R627
IC3503
R3533
FB1104 D9501
D508 R522
C1178
C1189
C1184
C1188
R1195
R628
FB506 R533
D509
R3539
R3538
R3540
R503
R9679
R9680
FB507 R655 R547 IC501
R549
R502
D510 FB9621 E
IC3303
FB9622
FB9601
C4438
R3397 R3396
C4422
C4421
C4445
FB9602
X4402
C4444 C4441 C2604
D3330 C3359 C2603
R4401 C2606
D3306 C3394
C3395 C2605
D3305 C2608
C2607
R3441 R3439 C2610
C2609
R3440 D3317 FB9606
R3443
R3406
D3316 R3401 FB9604
R3321
D3303
IC4405
R3427
C3362
C3389
D3314
R3429
FB9610
C4447 R3351
D3310
F
C9608
R3403
R3407
R3408
R3413 R3371 C3372 FB9607
R3320
R1104
R3412 FB9611
R3402
D3315
D3308
D3309
D3311
D3312
D3313
R3370 C3371
R3361 C9648
R1132
R3368
R3359
R3369
D3321 FB9608
R3360
R3349 R3347
C9649
Q1108
R3424
R3398
R3358
R4457
R3410 L9605
C9635
FB9612
R9667
C1121
R1213
R1183 R1182 R3365 R4455
R1161
R1181 R1180 R4459
R3430
R3431
C9669
R3314
R3313
R3310
R3309
C1183
C1190
R1206
C1109
IC1110 C9606
C9628
C9609 IC9604 IC9607
C9629
C1199 R3422
R1214 C1197 R3423 C9610
FB9609
FB9620
FB9615
FB9619
FB9614
FB9616
FB9613
R1209
C1193 C1182 C1181 R1204 R1203 R1205
C9650
C9651
C9653
C9654
C9655
R1141 C1176 C1177 C9612
C1195
C1127
C1108
R1144
C1106
R1143
R9652
C9652
R3433
R3340
C1180 R1102 C1174 R1103 C1175 C1179 R1130 R8462
G
R1217
R1129 R1131
R1187
R8461
IC1109 R8401 R8463 L9602 L9601
R8472 IC9605
R8416
C9611
IC8455
C1185
R8480 C9622
R8417 R8418
R8464 C8460
C8462 C8461
C1196
C1139
C563 C9621
R1186
C9602
C561 R8419
Q9601
C9620 C9625
R592
R3432 IC9602
C9601 R9666
IC503 R9671 R9672
R596
R1185
L1501
L1502
L1503
L1504
R602
C1107 C1125 C9623
D527 L9604
Q505
L1101 R3364
R1159
C555
R4414
C4462
C4461
L9603
D1514
R1162 R4413
C1540
L9606 C9645
R1582
R1537
R1584
R1166
P9604
P9601
R1538 IC9606
R1165
L1506
X4401
R1555
L1507
C9616
R1567
R1164 R1543
R1533
R1534
R1514
C9638
R4404
R1541 R1542
C1111
R1535
C4403 R4405 C4401
L1102 C1523 C9617
H
C1519
R1509
C1128 IC9608
R1554 R1557 C9639
FB1515 FB1512 C2812 C2761 C2759
R4409
R2836
R2834
C2754
R2759
C2762
R1531 C1532 C2760
IC4402 R1526 C2810
Q2703
IC1102 C1526 C1525 R2744
L1505
R4419
IC2704
R8411
R1527 IC2809 C2790
C2768
R2816
R2833
R2835
IC2807
R2822
R2819
R1525 C2806
C1524 C2789
R8488
R8489
R1523
C4437
R8490
R8491
R2739
C2702
C2823
C2765
R4418
C1521
R2826 R2753
C2807
IC1504
R1522 C1506 R2820
R1580 R1521 C1505 C1504 R2818
SC4401 R2821
R4417
FB503 R1579 VA8402 VA8404 VA8407
C502
R1520
J501 R1578 R1617
R512
R2823
C2809
R1550 R1616
C501
R514 R1549 R1615
R2825
C508 R1548 R1614
R1547 R1613
FB502
R524
R1546 R1612
R1568 R1611
C510
R511
R517
R523
R1571 R1610 FB1504
L9503
R1572
I
C564 R1573 R1574 R1515 R1592
R607
R1575 R1544
IC1505
R598 VA9502 VA9501
C1501 R1501
R1576
R1581
R1583
R1585
R1597
R1598
R1599
R1600
R1601
R1602
R1603
R1604
R1605
R1606
R1607
R1608
R1609
D1520 R1577 R1540
C1534
R614 R612 R1516
FL516
FB531
C1527
R601
C569
R605
R600
C566
R603
D1517 C560
Q1501
R1529
R1530
R606
D1502
D1515 R590
IC1506
C557
R597
C565
R599
R595
R589
SC8454
FB536
FB532
IC1507
C556
IC1501
R593
D1501
D1503
C552
C1508
D1507
VA1505
VA1507
D1519 D1516 IC1502
C553 R1503 IC1503 D1513 FB522 C554
D1504
D1508 R1512 FB521
R1513 R1528 R1508 R1510 R1518 R1560
D1506 R1505 R1504 R1506
J9502
SC1504 SC1505 SC1501 SC1502 SC1503
J
MAIN Unit (Chip Side-A)
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit (Side-B)
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1–3
19
18
17
R9647 FB9617 C2717
C9640
FB9605 R2768
Q9606
FB9618 C2750
IC9609
C2785
C9646
D2710
Q9605
D9614
C9665
R9631
R9645 R9644 FB2711 R2805
D2706
FB9603 C9642
C2736
R9654 R9664
C2741
C9647 R9637 FB2712 R2798
Q2704
IC9611 C2749
C2740
R9649
R9651 C2710
IC9601 C2792
Q2702
R9660 R2767
C2709
C9660 C2751 R2789 R2748
C9603
R9641
C2742
R9608 R2755
R9650
C2737
FB2710 R2799
R9648 R9646
D2707
IC9610 C2793 R2780
R9683
R9682
R9681
R9658
FB2709
Q2701
R9643
D2701
R2817 R2762
C9644 C9607 C9637
R9607 C9605
R9639 C9643
R9628 C9636
C2713
C2708
C9641
C9604
C9630
VA8408
16
R2701 IC2707
C2753
R9638 R9605 R9622 R2761
C8472
R2723
R8405
R9636 R9603 R9618 R2722
R9635 R9602 R9617 C2704 C2755 C2724
R2721
R9601 R9616
IC8456
R9632
C2703
D2705
R2772
VA8406
D9610 D9613 D9602 D9601 D9607 D9608 C2705 C2706
R2724
R2727
D2708
IC3301
C8473 C2743
C2730
C2752
R2784
C2707 R2731
R2839
R2764
C3301
R2770
R8412
FB8401 C2734 R2837
R2713
R2711
R2712
Q9602
R2714
D9611 R9630 R9619 FB2701
R8409
R9627
C3302 C2722
R2708
R2709
R2715
R9611
R9612
R2838
C9668
R9668 FB2702
R2777
R2778
R2776
C2783
Q9603
R9633
VA8401
R8404
R9634
R9610 D2704
R9609 C9614
Q9604
C2715
C9624
R8402
R2841
R8406
C9634 R9629 R9614 C9618
C9619
R9613
C9631
R2842
R9623 R9620
Q506 C2714
C559 R2751
C558
R591
C2746
15
VA8403
R594 R2757 R2773
R9621 C9627 FB2708
C604 R671 R672 R2774
C3531
FB2707 R2840
D9604 D9603 C2723
R2775
R8410
Q510 D2711 D9605
R2766
D2703
R8408
FL3508
VA8405 D9606
R8403 R8413 C2739
R9626
C2712
C2784
R9625
C2727
C3534
R9624
R9615 C9626
C9633 C3521
FL3507
R3548 R3547
C3527
C9632 C3524
C3526 C2725
R3546
R3543
C3519
D2702
C3523
D9612 D9609 C3520
R3544
R2605
R2606
14
FL3509 FB2614
C3525
FB2610
C3532
C3522
FL3505
C3512 FB2608
R604
R588
FB2604
C3510
R3517
FB2605
FB2616
C3516
FB9502 C9512
R9511 R9508
FB2601
FB2602
R3520 R3521
C3518 R3522
C3514
C3325 FL3506
R3308
R3409
IC9502
R9507 R9506
C8403 R3307
C3515
C3319 C3517
IC8405
C3321 R3312
R9505
C2819
R3426
R3425
C2821 R3419
C3331
R3420
FB9501 C9510 R2830 C3310
13
C3309
C3304
FB3304
C2820 R3352 C3340 C3341 R3344 C3332 C2602
R3329 C3308
R3327
C9615 FB3302
R2831
IC8404
C8402
R3338
C3338
IC9603
R2832
C3337
X2807
C3342
C3303 R3523 R3524 R3525 FB2615
IC2601
R3411
C3307
R2620
C3324
R3526
R3527
R3528
R3529
R2828 R3421
R2613
R2829
C9613 R3428
C3318 C3320
IC2808
C2816
R2827
C2822
R3322 R2602
C2815 C3313
R3319
R2824 C3330
C2814
C3329
C3328 C3312
R3341
C2817
C1528 C3327
C2818
R1532 IC1508 C3502
C3336
Q1502
R3436
C3334
C3505
C3344
C3306
C2811
C2813
R3417
C3386
R1564 R3323 R3324 C3346 C3316 C3501 R3502
C2808
C3504
C3335
R1536 R3354
C3387
R3418
D1512 R3501
C3315
C3348
R3353
R3350 C3354
R1507 L3301 C3305
R3333
R2637
C3353
C3355 FL3501
C3347
Q2603
C3349 C3333 C3396
C3392
C3393
R2638
R2635
C1502
R1511 C1535 R1517 R1519
R1502
C3351 C3503 C3506
12
R3505 C3508
C3509 R3504
C1503
FB2631
R2639
R2653
R3503
FB2629
C3326 C3323 FL3502 C3533
C3345
C3322 FB2628
R3343
C3343
R2645 FB2627
R1589 R1590
R3335
R3326
C3398
R3339
FL3503
C3381 R3390 FB3301 FB2626
R3345
R3346
R3325 FB2625
C3507
R3435
R2642
R2643 R2636
R3437
R1595
FB2624
R3337
R3416
R3317
R3318
R3316
R3315
R3434 R2647
R3438
C3377 R3386
FB2623
Q9607
C3397
C3350
X3301
C3391
R3336
R9604
C3380 R3389
R2615
C3390 R2656 FB2638
D1509
R2616
R9606
R3334 R2649
R1594 R2648
R1596
C3376 R3385 C3352 C3339 FB2636
R3387
R3391
R3393
R3394
R1563
C1509
R1587 R1565 C3379 R3388 C3314 R3303 FB2635
C3388
C3373 R3379
IC2005
C3378
C3382
C3384
C3385
C8456
Q1510
R2053
R1593
R1562
C3374
VA1508
VA1506 C3383 R3392 R3380
D3301
R3328
R3311
IC2003
R3414
R3404
R1566 R1586 IC3302
R3405
C2021
FB2634
R3330
C2017
R3415
C3311 R8481 R2047
Q3301 R2059
R3400
D2003 R2052 R2019 FB2633
11
R3399 R2055
C2016 R2054
R1558
R1559 Q1509
D3331
R8487
R2064 R2065
D2005
C2008
R1569 FB2632
Q1508
C3358 R3363
FB1537 R2066
D3326
D3323
D3328
D3307
D3304
D3319
D3327
R1621 R1570
C1555
C1554 IC2002
C1564
IC8401
R1623
R1618
D2002
C1550
D8456
C1549 C3357 R3362
R2061
C8470 R8478
R8479
C8471
C1563 IC2007
C2018
R1619 R2028 C2009
1–4
C3356 R3372
D8455
D3329
D3322
D3325
D3324
D3318
D3320
VA1504 C1516 C2006
R1552
VA1502 C1518 C3360 R3367 C2015
C1544
C1545
C1561
R8482
R8483
R8477
C3364 C3363 C3365 C3361 C3369 C3368 C3367
C1542
C3366
R3383
C3370
IC1509 C1546 R1539 R3374 R3373 C3375 R3395
R2029
Q2004
Q2003
C1531 R3375 R3381 R3382 R3377 R3376 R3384
R3378
R1588
R1629
C1533
C1520
C1541 C1548 R8467
C1513
C1514
R1591 R1551
C1547
R8453
R2035
R1553
C1543 C1562
C1522 R1556 D2007
R8452
R2002
Q2002
C1539
C1565
R1622
C1512
C1511
C1510 C8455
10
IC8452 D2006
R1524 R2050
C1538
D1518
R1545
R8420
R1620 FB1538
C1556 C8458
R658 C578
R620
C1557
C1558
FB1505
R501
C579
C2020 C577
C1566
C1553
D515
FB4410
C521
R551
C1515
C1517
Q508
C1552
R2058
R661
Q2005
IC2004 Q507
C1551 R2057
R660
R659
R2017
VA1501
VA1503
9
D1505
R4406
D4401
R4403 R3355
C4402
FB4401
C4405
C4404
FB1105
R3356 R4453
R3357
R4411
C4467
L4401
D1510
C4406 C4407
C1198
C4413
C4409
C4415
FB4403
D1511 R4402
R4458
FB2618
FB2619
C4408
D4402 R4448
FB4402
R4412
C4465 R4449
C4458
R4451
R4452
R1107
R1106
C4412
C4442 C4443
C1507
C4418
IC4401
C4417
C4420 R4456 C4453
C4419 R4415
C4440
C4452
R1561
C4439
C4457
R3366
C4427
FB2620
FB2630
R4416 C4414
R1215
R1188
C4428 C4426 C4456 C4411
8
R1160
R1189
R4450
R1216
C1126
R610
C4455
C4454
VA1510
VA1509
C4464
C4463
R1190 R611
C4410
R513
Q2011
R616
R572 R562
R515 R528
R1140 C4449 C4416 FB514
R538
R548
C518
FB2001
C4448
C524
C509
R559
R1127
R1192
R1191
R1120 R1108 R1207 R1139 R2007
D2001
R1145
C505
R525
R543
C514
R536 R558
R1134
R1184
C1113
C1117
C527
FB513
R1125
R1111
C1115
R1137
R1138
FB2005
R617
R1128
C1116
D1104
IC1105
R1142 FL504
R1136
C544
FB2003
7
R579
C529
FB519
FB2012
C1201
C1119 R1197 R2005
R1126 R2004
D1103
D1101
C1200
R1196 R573 R563
FB2013
R527
C507 R534
R1133 C1114
C2023
R1105
FB510
R557
R510
C516
R546
FB1101
C1102
R1122
C1104
C520
C1120 C1101
FB2002
D1102 R1110 R509
FB2014
C4459 R521
FB509
R531
C513
R542
R556
C504
C4451
FB2011
R1147
R1148
R1154
R1155
R4432
C4433
C4450
R1157
R1156
R1158
C4436
C526
R586 R2020 R2022
IC4403
FB520 R2018
FB2024
C545
C4424
Q2010
R2067
IC4404
R4431
R4433 R4437
FB4409
C547
C4460
R580
FL505
C534
C4423
R4439 C4435
FB2023
R582
6
R4434
C1192
R4425
FB526 C596
VA508
R4446
FB540
FL511
IC1108
FL507
R4435
R561
C525
R540
C536 R520 FB516 R537
R529
C512
R550
C519
C1191
R4444
VA509
R560 FB541
C597
C528
R4424
R539
FL512
D4403 C4466
R566
R574
R519 FB515
R526
C506
R545
C515
R541
L1104
C1112
L1105
R4454
R4423
C535 R575 R544
FB537
R570
FL506 R634
VA510
FL513
C598
C1118
C1131
R1168
R1167
FB524 R577 FB529
5
C4430
C4431
C549
R584 FL514
C546
C540
FB4408
R581
IC1103
FB9511
R1109
C1122
C550
R585 FL515
R4430
C4432
C541
R578 FB530
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
C1132 R633
R4422
FB9513
C4429
C537
R576 FB528 C607
FB511
C523
FL510
C548
R1211
R4421
R583
C608
R587
FB512
R553
R4441
R4443 L1107 C522
R552
4
C2781
R4436
C2769
L1103 C9513 C9514
R9524
R9525
R9526
R9527
C1129
R1169
R2782
C2772
C9501 C9502 C2787 R554
R1170 R2781
C2788
C9504 C9505 C530
C2786
R4420
C1103 C1130 R2791 C2763
C2771
C9564
R2790
IC2706
R2783
C2770
R4438 FB9510
C4434
R2788
C9562
R4426
R9554
C531
C9554
IC1107
C9560 R555
C9559
R9519
C9563
FB9509
C9518
R9522
R1163
C9553
C1154
MAIN Unit (Chip Side-B)
IC9503
R1151 C9503
C1123
R1135 R9555
R1121 R1119 R1118
R1202
Q1106
C1153 R1124 R1171
R1208
FB9504
R1201
R1117 R1123
R1179
3
Q1107
R1199 C1161
C1145 C9516
R1212 FB9508 FB9503
C1110 R1101 R1200
R1149
IC1104
R1210 FB9507
C1124 C1194
R1198 R1150
R1178
C1140
C1138 R1114
R1112
Q1103
Q1102
C1173
C1141
R1113 R1177
C1105
FB1103
R1176
2
1
G
A
H
C
E
F
J
I
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] R/C, Operation Unit
R/C, Operation Unit (Side-A) R/C, Operation Unit (Chip Side-A) R/C, Operation Unit (Side-B)
J
R120
H
C103
C104
G
F
D104
C106
R106
E
R109
R113
IC101
P103
D
C105
C101
C102
C
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1–5
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[3] ICON Unit
J ICON Unit (Side-A) ICON Unit (Side-B)
ICON Unit (Chip Side-A)
D P202
P201
C252
R202 D252
C251
C C253
D202
R252
D251
R212
R203
R205
R206
R214
R204
R201
R251
R213
R211
D206
C254
D217 D213 D215 D212 D214 D211
D205
D204
D201
D203
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
1–6
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
CHAPTER 2. SCHEMATIC DIAGRAM
LC-40LE830U
Service Manual
[1] DESCRIPTION OF SCHEMATIC DIAGRAM
1. VOLTAGE MEASUREMENT CONDITION:
1) The voltages at test points are measured on exclusive AC adaptor and the stable supply voltage of AC 120V. Signals are fed by a color bar signal genera-
tor for servicing purpose and the above voltages are measured with a 20k ohm/V tester.
2. INDICATION OF RESISTOR & CAPACITOR:
RESISTOR
1) The unit of resistance "Ω" is omitted.
(K=kΩ=1000Ω, M=MΩ).
2) All resistors are ± 5%, unless otherwise noted.
(K= ± 10%, F= ± 1%, D= ± 0.5%)
3) All resistors are 1/16W, unless otherwise noted.
CAPACITOR
1) All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2) All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH " "( ) ARE IMPORTANT
FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO
REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAIN-
TAINING THE SAFETY AND PERFORMANCE OF THE SET.
AVIS DE SECURITE IMPORTANT:
LES PIECES MARQUEES " "( ) SONT IMPOR-
TANTES POUR MAINTENIR LA SECURITE DE L'APPAREIL.
NE REMPLACER CES PIEDES QUE PAR DES PIECES DONT LE
NUMERO EST SPECIFIE POUR MAINTENIR LA SECURITE ET
PROTEGER LE BON FONCTIONNEMENT DE L'APPAREIL.
2–1
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
[2] SCHEMATIC DIAGRAM
MAIN Unit-1 (LC-40/46/52/60LE835U)
MAIN1(TUNER)
J
DUNTKF733WE12
H *TU1105
AA073WJQZ
US
ATSC-DIF
*R1112 *C1141
10K 10u 16V
1 2 3 4 5 6 7 8 9 10 11 12 KZA837WJQZ
*C1138
0.1u K 9.0
TL1108
*R1178 10V
*Q1102
TU_SIF 3.8 2SC3928AR
0
*R1177
G
100
3.2
D__IF+
D__IF-
*R1113
TU_GAIN_SW
N_TU_RESET
IF___AGC
*R1176
TU_AIF+/CVBS
10K 330
TO MAIN10(POWER)
IF+1.8V
TU_AIF-/SIF
TU_SCLK
TU_SDATA
010
IF+3.3V
D+5V
010
D+3.3V
*C1145 *R1117 *R1121
10u 10V 10K 390 *C1153
*R1179 KZA616WJQZ *R1119 0.01u
F TL1109
0 10 25V
AT+5V
TU_CVBS
TUNER_CVBS
3.3
*TL1102 *R1118 2.6
10K
*Q1106
C1133
0.1u 10V TL1103 R1101 ISA1530AC 0
1K
N_TUN_RST
TL1101 *TL1104 *R1144
100 TP1111
TO MAIN4(CPU)
E *FB1103 TUN_AIF-/SIF 004
A192WJ NIM_RST
*TL1105 *R1210 004
*C1105 SIF
0
1000P
C1124 *R1143
004
TL1107 0.1u 100 *R1212 TUNER_CVBS
C1110
0
0.01u 25V
*R1151
*TL1112
4.7K
C1185 *R1149
TUN_AIF+/CVBS 0 004
0.01u TL1106 *R1158 CPU_ATV_IFP
25V
0 *R1150
D *C1123 *TL1110 *R1201 0 004
0.01u 0 CPU_ATV_IFN
D_IF-
*C1127 N_TUN_RST 004
10u 16V *TL1111 N_TUN_RST
KZA837WJQZ D_IF+
*R1202
0
*R1196 *R1197
R1211
2.2K 2.2K
2.2 1/2W TO MAIN11(DEMOD_CI)
TU_SCL 011
TWF TU_SCL
C 5 4 TU_SDA 011
TU_SDA
Vout Vin
C1195
4.7u
IC1109 C1196
L1107
10uH
011
ATSC_IF_AGC
10V 4.7u *R1160
KZA761WJQZ
S170B18U 10V CEM *C1126
KZA761WJQZ 0.01u 4.7K
*C1129 *R1148
25V 0 011
10u
ATSC_IFN
GND 16V
ON N.C *R1147
KZA837WJQZ 0 011
1 2 3 ATSC_IFP
B
D+3.3V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2–2
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit-1 (LC-40/46/52/60LE830U/832U/LC-60LE831U) MAIN1(TUNER)
J
*TL1102
TU_GAIN_SW
TL1103 R1101
1K
N_TU_RESET N_TUN_RST
*TL1104 *R1144
100
TU_SDATA TU_SDA
*TL1105
TU_SCLK TU_SCL
C1124 *R1143
0.1u 100
TO MAIN10(POWER)
D+5V 010
D+5V
D+3.3V 010
D+3.3V
*C1141
10u 16V
KZA837WJQZ TO MAIN11(DEMOD_CI)
TS_TUOUT_D7 011
TS_TUOUT_D7
TS_TUOUT_D6 011
9.0 TS_TUOUT_D6
*R1112
10K
3.8 *Q1102 TS_TUOUT_D5 011
2SC3928AR TS_TUOUT_D5
TS_TUOUT_D4 011
TS_TUOUT_D4
3.2 *R1177 011
G IF+1.8V
100
TS_TUOUT_D3
TS_TUOUT_D3
TS_TUOUT_D2 011
TS_TUOUT_D2
*R1113 *R1176
10K 330 TS_TUOUT_D1 011
TS_TUOUT_D1
TS_TUOUT_D0 011
*C1138 TS_TUOUT_D0
0.1u K
TS_TUOUT_VAL 011
10V TS_TUOUT_VAL
TS_TUOUT_SYNC 011
TL1106 TS_TUOUT_SYNC
TS_TUOUT_CLK 011
TS_TUOUT_CLK
C1185 *C1127
0.01u 10u 16V
25V KZA837WJQZ
*R1178
TL1108
TU_AIF-/SIF TU_SIF
0
*R1210
TO MAIN4(CPU)
F TL1101 *FB1103 *R1179
0
A192WJ *C1145 004
AT+5V TL1109 0 TUN_GAIN_SW
TU_CVBS 10u 10V
IF+3.3V *R1121
*C1105 TU_AIF+/CVBS TUN_AIF+/CVBS KZA616WJQZ *C1153
390 *R1149
TUN_AIF+/CVBS 004
1000P 0.01u CPU_ATV_IFP
*R1117 0
10K 25V *R1150
TUN_AIF-/SIF 004
*R1212
*Q1106 0 CPU_ATV_IFN
N_TUN_RST 004
*TU1105
US ISA1530AC
0
TL1107 N_TUN_RST
AA073WJQZ L1107 3.3
10uH *R1119 N_TUN_SAT_RST 004
ATSC-DIF CEM
10 2.6 N_TUN_SAT_RST
C1110 IF__AGC
0.01u
25V 0
1 2 3 4 5 6 7 8 9 10 11 12 *R1118
10K R1196 R1197
*TL1110 *R1201
2.2K 2.2K
0 D_IF-
D__IF-
TO MAIN11(DEMOD_CI)
*TL1111 TU_SCL 011
AT+5V
TU_SCL
D__IF+ D_IF+
TU_AIF+/CVBS
TU_GAIN_SW
N_TU_RESET
TU_AIF-/SIF
TU_SDA 011
TU_SDATA
IF+1.8V
IF___AGC
*R1202
TU_SCLK
TU_SDA
IF+3.3V
0
D__IF+
TUNER_CVBS
D__IF-
*R1151
*TL1112
4.7K IF__AGC D_IF-
IF___AGC
E *C1129
10u
D_IF+
*C1123
16V
0.01u
KZA837WJQZ
SAT_SDA
TO MAIN11(DEMOD_CI)
SAT_SCL 011
SAT_SCL
011
SAT_SDA
*R1148
0 011
ATSC_IFN
*R1147
0 011
ATSC_IFP
011
ATSC_IF_AGC
*R1158 *R1160
*C1126
0 4.7K TP1111
TO MAIN4(CPU)
0.01u 004
25V NIM_RST
004
SIF
004
D TUNER_CVBS
TP1112
*TL1154
LNB_CTRL_0 TO MAIN6(FLASH)
006
SCL0_400k
TP1110
006
SDA0_400k
R1211
2.2 1/2W
TWF
5 4
Vout Vin
C1195 IC1109 C1196
4.7u
Near Tuner
10V 4.7u
S170B18U 10V
KZA761WJQZ KZA761WJQZ
B ON
GND
N.C
1 2 3
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2–3
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit-2 (LC-40/46/52/60LE835U)
MAIN2(TERMINAL)
J DUNTKF733WE12
TO MAIN10(POWER)
010
D+3.3V
010
D+5V
R658
0 010
BU+3.3V
TO MAIN7(UCOM)
007
IR_RS
C578
0.1u
I 10V
11
R608 *C577
100 R620
FB527 10u
10K TO MAIN6(FLASH)
5
A042WJ 1/10W 10V 006
KZA616WJQZ UART_CPUTO232C
9
006
UART_232CTOCPU
4
CTS R609
8 FB525 100 3.3 3.3 0 0 0 3.3 0 3.3
A042WJ 1/10W
16 15 14 13 12 11 10 9
TxD 3
Vcc GND T1_out T1_in R1_out
RTS SHDN NC
7 FB523
A042WJ
FORCEON
IC506
RxD 2
R572 DSR M3221EIP
*R562 R613
4.7K 6
100 VA501 D525 100
CVBS2_PLUG VA502
VXA005WJ EXA697WJQZ 1/10W EN C1+ V+ C1- C2+ C2- V- R1_in
DCD 1 VXA005WJ
*R513 *R536 5.6V
*FB513
1K *R525 1K 1 2 3 4 5 6 7 8
A074WJ 10
CVBS2_IN_R 100K
*FB519 0 3.3 3.3 3.3 3.3 0 0 0
A204WJ *R617
0 SC/Y_CVBS2_IN
*C505
1000P *R538
*R515 *FB514 SC504
1K 1K *C527
A074WJ NA818WJ
H CVBS2_IN_L 1000P D-SUB
RS232C C579 C580 C584 C586
*C509 0.1u 0.1u 0.1u
*J510 Vertical type 0.1u
1000P 10V 10V 10V
ZA100WJQZ *R579 *C544 10V
*C524 470P
75
1000P for US/CN 50V
1/4W
*R528
100K
1
SC501
2
NA816WJ
R573 PC_IN FB504
3
R531 R563 4.7K 16
R509 FB509 Vertical Type A042WJ
R521 1K 100
1K A074WJ CVBS1_PLUG
4
CVBS1_IN_R 100K 6 R522
220
1 11
5
C526 D508 D515
C504 7 FB505 EXA697WJQZ
EXA697WJQZ
TO MAIN3(HDMI)
R534 1000P FB520
R510 1000P FB510 A042WJ R654 *R501
A204WJ 5.6V 4.7K 5.6V CZ
1K 1K CVBS1_IN 2 12 0 003
A074WJ R625 VGA_PWR5V
CVBS1_IN_L D507
6
8 EXA697WJQZ 1K R655
4.7K *R502
5.6V 0 CZ 003
3 13 VGA_SCL
7
C507 R627
1000P R586 9 47K *R503
2 1 0 CZ 003
C520 0 CVBS_COM VGA_SDA
8
1000P 4 14
D510
FB506 4 3
G R580 C545 10 EXA697WJQZ
9
R527 75 470P A042WJ 5.6V
100K 50V 5 15 6 5
1/4W
FB507
10
17 A042WJ R533
D509 8 7
220
EXA697WJQZ
R574
5.6V D512
4.7K
1SS184
S1_PLUG R547
11
R519 R539 FB515 100
R526 1K 1
1K A074WJ
COMP1_IN_R 100K
12 3
2
C528
13
C506
1000P R540 1000P
R520 FB516
1K 1K A074WJ
COMP1_IN_L FB535
TO MAIN4(CPU)
A527WJ
14
C512 R628 004
PC_VSYNC DSUB_WP
1000P R507 1K
C525
15
75 PC_HSYNC
1000P FB534 004
A527WJ 1/4W SC/Y_CVBS2_IN
16
R529 PC_BLUE
100K R506 004
17
FB533 PC_GREEN COMP1_Y
75
A527WJ 1/4W
PC_RED 004
18
COMP1_Pb
F R505
75
004
COMP1_Pr
1/4W 004
COMP1_COM
R615 TO MAIN4(CPU)
0 CZ PC_RGB_COM
004 004
PC_HSYNC ANALOG_SY0
004 004
PC_VSYNC ANALOG_SC0
R575
R570 4.7K 004
100 004 CVBS1_IN
COMP1_PLUG PC_RED
R633 004 004
PC_GREEN CVBS_COM
0 COMP1_SOY
PC_HDMI_L
J501 004
FB528 PC_BLUE
R576 EA111WJQZ FB502 R511 R523
A204WJ A074WJ R517
COMP1_Y 1K 1K
18 PC AUDIO_IN 100K 004 004
1 R512 R524 PC_RGB_COM
FB503 COMP1_PLUG
A074WJ 1K 1K
3 PC_HDMI_R 004
004 S1_PLUG
2 PC_HDMI_L
R587 COMP1_COM C510
R514 1000P 004 004
0 100K CVBS1_PLUG
CH PC_HDMI_R
R583 C548
56 10P 004
50V CVBS2_PLUG
1/4W
E FB529
A204WJ R577
18 COMP1_Pb
C501
220P
C502
220P
C508
1000P
004
SLOWSW1
CH
R504
10K
R584 C549 R604
56 10P 100K HP_PLUG
50V
1/4W UN-PLUGGED:H
TO MAIN4(CPU)
FB530 PLUGGED:L
R588
A204WJ R578 1K
18 COMP1_Pr 004
HP_PLUG
J504
EA113WJQZ
R606
33 TO MAIN9(AUDIO AMP)
1
FB521
A074WJ 1/4W TW
R585 C550 009
10P MONI_HP_R
56
2
50V
1/4W
009
MONI_HP_L
3
FB522 Q506
009
A074WJ IMH23T110 Q510 AUDIO_MUTE
4
0 0 ISA1530AC
HP Jack/AUDIO OUT 3.2 3.3 009
3
HPOUT_MUTE
2.66
R672
2
2.66 2.5 4.7K
5
R590 R593
C554 C560
100 100
1000P 1000P R671
1/4W 1/4W
TW 0 0 1K
TW
1
R607
33
1/4W
R591 R594 TW
100K 100K
C558 C559
0.01u 0.01u TO MAIN4(CPU)
004
C 004
COMP1_SOY
CVBS1_IN_R
004
CVBS1_IN_L
*R667
CVBS2_IN_R 0 004
CVBS_IN2_R
*R669
CVBS2_IN_L 0 004
CVBS_IN2_L
004
COMP1_IN_R
004
COMP1_IN_L
B D527
RFT4112S
3.6
IC503 0
3
7
004
2.4
OPT_OUT
5
2
1
5 5 AUDIO_MUTE
1
R592
100
SPDIF BUFFER R602
47K
Q505
& SPDIF MUTE
T7SET08U1E RT1N141U
MUTE
C555
0.1u
10V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2–4
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit-2 (LC-40/46/52/60LE830U/832U/LC-60LE831U)
MAIN2(TERMINAL)
J
TO MAIN10(POWER)
010
D+3.3V
010
D+5V
DUNTKF733WE** 010
BU+3.3V
R658
0
C578
0.1u
I 10V
007
TO MAIN7(UCOM)
IR_RS
11
R608 *C577
100 R620
FB527 10u
10K TO MAIN6(FLASH)
5
A042WJ 1/10W 10V
IR_RS UART_CPUTO232C 006
KZA616WJQZ UART_CPUTO232C
9
UART_232CTOCPU
006
UART_232CTOCPU
4
CTS R609
8 FB525 100 3.3 3.3 0 0 0 3.3 0 3.3
A042WJ 1/10W
16 15 14 13 12 11 10 9
TxD 3
Vcc GND T1_out T1_in R1_out
RTS SHDN NC
7 FB523
A042WJ
FORCEON
IC506
RxD 2
R572 DSR M3221EIP
R613
4.7K 6
VA501 D525 100
*FB513 *R562 CVBS2_PLUG VA502
VXA005WJ EXA697WJQZ 1/10W EN C1+ V+ C1- C2+ C2- V- R1_in
A074WJ 100 DCD 1 VXA005WJ
*R513 *R536 5.6V
1K *R525 1K 1 2 3 4 5 6 7 8
CVBS2_IN_R 100K 10
*C505 0 3.3 3.3 3.3 3.3 0 0 0
*FB519 *R617
1000P 0 SC/Y_CVBS2_IN
*FB514 A204WJ
A074WJ
*R515 *R538 SC504
1K 1K *C527
NA818WJ
CVBS2_IN_L *C509 1000P
H 1000P
D-SUB
RS232C C579 C580
0.1u
C584
0.1u
C586
0.1u
*J510 Vertical type 0.1u
10V 10V 10V
ZA100WJQZ *R579 *C544 10V
*C524 470P
*R528 75
1000P for US/CN 50V
100K 1/4W
1
SC501
2
NA816WJ
FB509 R573 PC_IN FB504
3
R531 A074WJ 16
R509 4.7K Vertical Type A042WJ
1K R521 1K R563 CVBS1_PLUG
4
CVBS1_IN_R 100K 6 R522
100
C504 220 *R501 TO MAIN3(HDMI)
0 CZ
1000P 1 11
5
FB510 D508 D515
7 FB505 EXA697WJQZ 003
A074WJ EXA697WJQZ VGA_PWR5V
R510 R534 FB520 A042WJ R654
C526 5.6V 4.7K 5.6V
1K 1K A204WJ CVBS1_IN 2 12 *R502
CVBS1_IN_L C507 1000P D507 R625 0 CZ 003
6
8 EXA697WJQZ 1K R655 VGA_SCL
1000P
5.6V 4.7K *R503
3 13 0 CZ 003
7
VGA_SDA
9 2 1 R627
C520 R586 CVBS_COM
R527
1000P 8 0 4 14 47K
100K D510
R580 C545 FB506 4 3 R628 004
10 EXA697WJQZ
DSUB_WP
9
G 75
1/4W
470P
50V 5 15
A042WJ 5.6V
6 5
1K
FB507
10
17 A042WJ R533
D509 8 7
220
EXA697WJQZ
R574
5.6V D512
4.7K
FB515 1SS184
S1_PLUG R547
A074WJ TO MAIN4(CPU)
11
R519 R539 100
R526 1K 1
1K
COMP1_IN_R 100K 004
12
3 SC/Y_CVBS2_IN
C506
1000P 2
13
FB516
A074WJ 004
R520 R540
C528 RED1/C1
1K 1K
COMP1_IN_L C512 1000P FB535 004
1000P A527WJ GREEN1
14
004
PC_VSYNC BLUE1
R507
C525
15
R529 75 PC_HSYNC 004
1000P FB534 SC_RGB_COM
100K 1/4W
A527WJ
16
PC_BLUE
R506 004
17
PC_GREEN COMP1_Y
75
1/4W
PC_RED 004
18
COMP1_Pb
FB533
F A527WJ R505
75
004
COMP1_Pr
1/4W 004
COMP1_COM
R615 TO MAIN4(CPU)
0 CZ PC_RGB_COM
004 004
PC_HSYNC ANALOG_SY0
004 004
PC_VSYNC ANALOG_SC0
R575
4.7K 004
004 CVBS1_IN
R570 COMP1_PLUG PC_RED
100 004 004
PC_GREEN CVBS_COM
R633 COMP1_SOY PC_HDMI_L
0 004
J501
FB502 R511 PC_BLUE
FB528 EA111WJQZ R517 R523
COMP1_Y A074WJ 1K 1K
A204WJ R576 PC AUDIO_IN 100K 004
PC_RGB_COM 004
18 1 R512 R524 COMP1_PLUG
FB503
COMP1_COM 1K 1K
3 A074WJ PC_HDMI_R 004
004 S1_PLUG
2 PC_HDMI_L
R587 C510
R514 1000P 004 004
0 100K CVBS1_PLUG
CH PC_HDMI_R
R583 C548
56 10P 004
50V CVBS2_PLUG
1/4W
004
C502
E FB529
A204WJ R577
18
COMP1_Pb
C501
220P 220P
C508
1000P
CH
SLOWSW1
004
SC1FSW
TO MAIN1(TUNER)
001
R584 C549 TUNER_CVBS_BYPASS
56 10P J504 HP_PLUG
50V
1/4W EA113WJQZ UN-PLUGGED:H TO MAIN4(CPU)
004
1
PLUGGED:L CVBS_TU_OUT
FB530 R604
R578 COMP1_Pr R588 10K 004
A204WJ
1K HP_PLUG
18
2
R606
33 TO MAIN9(AUDIO AMP)
3
1/4W TW 009
MONI_HP_R
C550
4
R585 FB521 009
56 10P A074WJ MONI_HP_L
50V HP Jack/AUDIO OUT
1/4W
FB522
A074WJ
D Q506
IMH23T110
0 0
3
SLOWSW1
R590 R593 TO MAIN9(AUDIO AMP)
C554
100 C560 2.66 Q510
100
2
1000P 1000P ISA1530AC 009
1/4W 1/4W 2.66
TW 3.2 AUDIO_MUTE
5
R504 TW
10K
009
0 0 R672 TUNER_L_OUT
1
2.5 4.7K
009
TUNER_R_OUT
R671 009
1K HPOUT_MUTE
TO MAIN4(CPU)
R591 R594 R607 004
100K 100K SC1_IN_L
33
1/4W 004
TW SC1_IN_R
C558 C559
0.01u 0.01u
004
COMP1_SOY
C 004
CVBS1_IN_R
004
CVBS1_IN_L
*R667
CVBS2_IN_R 0 004
CVBS_IN2_R
*R669
CVBS2_IN_L 0 004
CVBS_IN2_L
004
COMP1_IN_R
004
COMP1_IN_L
D527
B RFT4112S
3.6
IC503 0
3
7
004
2.4
OPT_OUT
5
2
1
5 5 AUDIO_MUTE
1
R592
100
SPDIF BUFFER R602
47K
Q505
& SPDIF MUTE
T7SET08U1E RT1N141U
MUTE
C555
0.1u
10V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2–5
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit-3 (LC-40/46/52/60LE835U) MAIN3(HDMI)
J D1511
1SS184
D1517
DUNTKF733WE12
1 SC1505
HDMI4 1SS184
ZA264WJQZ
3
2 20 21 1
SC1501
HDMI3 2 4 6 8 10 12 14 16 18
ZA264WJQZ 3
11 13 15 17 19 2
20 21 1 3 5 7 9
22 23
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17 19 TL1512
22 23
HDMI3_POW5V
TP1510
TP1507
TP1506
TL1511 TL1513
TP1504
TP1505 R1536 TO MAIN7(UCOM)
TL1501 TL1510 0 007
HDMI_CEC_ HDMI_CEC_
TP1501
HDMI_CEC
TL1506 HDMI3_HPG
VA1501
VA1503
VXA074WJ IC1506 TO MAIN4(CPU)
VXA074WJ 39V
39V CM123408
I 1.1pF
1.1pF
004
HDMI_OPT_OUT
HDMI4_CLKN_222.75MHz
OUT4-
8
IN4-
IC1501 HDMI4_CLKP_222.75MHz
VA1509
VA1510
VXA074WJ
OUT4+ VXA074WJ 39V
CM123408 39V
10
IN4+
7
1.1pF
1.1pF
HDMI3_CLKN_222.75MHz HDMI4_D0N
OUT4- OUT3-
11
8
6
IN4- IN3-
L1501
HDMI3_CLKP_222.75MHz HDMI4_D0P
OUT4+ OUT3+ FA228WJ
TO MAIN4(CPU)
10
12
IN4+ IN3+
5
SW_TMDS_CLKN_222.75MHz_
HDMI3_D0N HDMI4_D1N 4 3 SW_TMDS_CLKN_222.75MHz
OUT3- OUT2- 004
11
13
6
4
IN3- IN2-
SW_TMDS_CLKP_222.75MHz_
1 2 SW_TMDS_CLKP_222.75MHz
L1502 004
HDMI3_D0P HDMI4_D1P FA228WJ
OUT3+ OUT2+
12
14
IN3+
3
IN2+
8
R1561
HDMI3_D1N 47K HDMI4_D2N 4 3 SW_TMDS_D0N
OUT2- OUT1- 004
IN1-
13
15
4
2
IN2- VRK
SW_TMDS_D0P_
D1512 1 2 SW_TMDS_D0P
L1503 004
1SS420
H
7
HDMI3_D1P HDMI4_D2P FA228WJ
OUT2+ OUT1+ IN1+
14
16
3
1
IN2+
HDMI4_HPG
R1507
HDMI3_D2N 4 3 SW_TMDS_D1N
OUT1- 27K 004
IN1-
15
HDMI4_SDA SW_TMDS_D1P_
1 2 SW_TMDS_D1P
HDMI_CEC_ L1504 004
HDMI4_SCL
HDMI3_D2P FA228WJ
OUT1+ IN1+
16
HDMI4_POW5V
R1540
4 3 SW_TMDS_D2N
HDMI3_SDA 10 004
D1508 SW_TMDS_D2P_
HDMI3_SCL 1 2 SW_TMDS_D2P
1SS184 004
1
3
SC1502 2
HDMI2
ZA264WJQZ
20 21
2 4 6 8 10 12 14 16 18
TO MAIN10(POWER SUPPLY)
1 3 5 7 9 11 13 15 17 19
22 23
010
HDMI2_POW5V BU+3.3V
G C1515 010
A192WJ
FB1505
A192WJ
0.1u C1517 C1557 D+3.3V
FB1538
10V 1000P 0.1u *C1558
TP1508
10V 1000P
SW_TMDS_D0N_
SW_TMDS_D1N_
SW_TMDS_D2N_
TP1511
SW_TMDS_D0P_
SW_TMDS_D1P_
SW_TMDS_D2P_
010
D+5V
TL1502 TL1507
TP1502
SW_TMDS_CLKN_222.75MHz_
SW_TMDS_CLKP_222.75MHz_
010
M+1.8V
TL1505 HDMI2_HPG TL1546
*C1546 *C1562 *C1551
TO MAIN11(DEMOD_CI)
C1547 C1553 *C1566
10u 1000P 10u 1000P *C1556
VA1502 0.1u 0.1u 011
VA1504 10V 10V 10u HDMI_SW_1.2V
VXA074WJ VXA074WJ 10V 10V
39V KZA616WJQZ KZA616WJQZ 10V
39V C1548 *C1552 KZA616WJQZ
1.1pF 1.1pF C1541
0.1u 10u *C1542
10V 10V 10u 0.1u
KZA616WJQZ 10V 10V
KZA616WJQZ 5 4
IC1502 VOUT VIN
CM123408
R1509
IC1509
HDMI2_CLKN_222.75MHz S172B12U
OUT4- 4.7K
9
IN4-
ON GND NC
OUT4+ HDMI2_CLKP_222.75MHz 1 2 3
10
IN4+
7
F OUT3- HDMI2_D0N
R1554
10K R1619 100K
11
IN3-
R1568 5.1
HDMI4_CLKN_222.75MHz R1623 100K
OUT3+ HDMI2_D0P R1571 5.1
100
80
79
78
77
76
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
HDMI4_CLKP_222.75MHz
12
IN3+
5
C1523
1u 10V
R1572 5.1
HDMI4_D0N
TXCN
CKZ
TXCP
TX0N
TX1N
TX2N
TX0P
TX1P
TX2P
R1XCN
R1XCP
R0XCN
R0XCP
RSVDL
RSVDL
R0X2N
R0X1N
R0X0N
VDD33
VDD12
R0X2P
R0X1P
R0X0P
Q1510
AVDD12
HDMI2_D1N
TVDD12
TO MAIN6(FLASH)
2
OUT2- HDMI2_POW5V *R1563
R1512 R1573 5.1
13
TPWR_CI2CA
4
IN2- R3PWR5V
SSM6N15FU
75
1
HDMI4_D0P 0
47K R1X0N R1555 006
VRK 10 SCL1
HDMI2_D1P *R1562
OUT2+ HDMI2_HPG 0 006
14
IN2+ R1X0P
74
2
SDA1
1
CBUS_HPD3
6
OUT1- HDMI2_D2N
IN1- R1X1N R1541
15
73
DSCL3
3
R1574 5.1 10 VRK
HDMI4_D1N
5
2
HDMI2_SCL
HDMI2_D2P R1575 5.1
OUT1+ IN1+ HDMI4_D1P 8 7
R1X1P DSDA3
16
72
4
HDMI2_SDA
R1576 5.1 6 5
HDMI2_SDA HDMI4_D2N
4
3
D1509 HDMI2_SCL R1577 5.1 R1X2N CSCL 4 3
71
5
HDMI4_D2P
1SS184
2 1
1
E R1X2P CSDA
70
6
SC1503
HDMI1 ZA264WJQZ 3
C1511
2 0.1u 10V R1565 4.7K
20 21 VDD33 TP1519
C1512
69
7
2 4 6 8 10 12 14 16 18 GPIO1 R1533
1000P R1566 4.7K
10K
*C1510
1 3 5 7 9 11 13 15 17 19 10u
22 23 R2XCN TP1520
10V GPIO0
68
8
R1581 5.1 R1534
HDMI3_CLKN_222.75MHz KZA616WJQZ
HDMI1_POW5V 10K R1514
R1583 5.1 10K
TP1512 HDMI3_CLKP_222.75MHz R2XCP
R1595 INT
67
9
TP1509
1K R1585 5.1
TL1508 HDMI3_D0N
R1597 5.1 R2X0N CEC_A TP1518 R1538
66
10
HDMI3_D0P 10K
TL1503 TL1504
*R1584
TP1503
*C1538 10
TL1535 10u 10V
R2X0P VGA_PWR5V
R5PWR5V(VGA) KZA616WJQZ
65
11 C1540
C1539 1u 10V CKZ
R1589 VA1508 0.1u 10V
VA1506 R2X1N SBVCC5
4.7K VXA074WJ
64
12
*C1565
VXA074WJ
39V
39V
1.1pF
*R1519
0
HDMI3_D1N
R1598 5.1
IC1504 1000P
R1524 10 R1545 0
1.1pF
SII9387
IC1503 HDMI3_D1P
R1599 5.1
R2X1P
HDMI_RSVD
63
13
CM123408 R1600 5.1
HDMI3_D2N
D OUT4-
HDMI1_CLKN_222.75MHz
R2X2N 3
VGA_SCL
9
R1601 5.1 DSCL5(VGA) 4
8
IN4-
62
14
HDMI3_D2P *R1537
HDMI1_SDA 10 VGA_SDA
1 2
HDMI1_CLKP_222.75MHz
OUT4+ R1553
DSDA5(VGA)
10
IN4+
7
R2X2P
61
15
10K
HDMI1_SCL C1513 R1556 FB1512
HDMI1_D0N 0.1u 10V 10 HDMI1_POW5V
OUT3- A192WJ
VDD33
11
IN3- C1514 R4PWR5V
60
16
1000P
C1522 R1567
Q1508
*C1543 1u 10V
HDMI1_D0P 0 2SA2061
OUT3+ 10u R3XCN CKZ
12
IN3+ CBUS_HPD4
5
10V
59
17
HDMI2_CLKN_222.75MHz
R1602 5.1 KZA616WJQZ 3.2 ˴˴˴˴˴˴˴˴
HDMI1_D1N R1603 5.1
OUT2- HDMI2_CLKP_222.75MHz HDMI1_SCL
R3XCP 3 4
13
IN2- DSCL4
58
18
R1569
R1582
R1604 5.1 HDMI1_SDA 2.5 10K
HDMI2_D0N 10
1 2
HDMI1_D1P
OUT2+
R1605 5.1 R3X0N DSDA4 R1551
14
IN2+
57
19
HDMI2_D0P 10K
R1552
OUT1- HDMI1_D2N 10 HDMI3_POW5V
IN1- R3X0P R2PWR5V R1558 Q1509
15
56
20
330 RT1N141U
C1520
HDMI1_D2P 1u 10V
OUT1+ IN1+ CKZ HDMI3_HPG
R3X1N
16
CBUS_HPD2
C
55
21
R1606 5.1
HDMI2_D1N
R1607 5.1 R3X1P HDMI3_SCL
HDMI2_D1P 3 4
DSCL2
54
22
R1608 5.1 HDMI3_SDA
HDMI2_D2N 1 2
R1543
R1609 5.1 R3X2N DSDA2 10
53
23
HDMI2_D2P
MICOM_VCC33
R3X2P *C1531
52
24
10u 10V
C1544 R1557
AVDD12 KZA616WJQZ 10
CBUS_HPD0
0.1u
CBUS_HPD1
HDMI4_POW5V
ETH_RX1N
ETH_RX1P
ETH_TX1N
ETH_TX1P
R0PWR5V
SPDIF_IN
R1PWR5V
EPWR33
51
25
C1545
DSDA0
R4XCN
R4X0N
R4X1N
R4X2N
VDD33
VDD12
DSCL0
R4XCP
DSDA1
R4X0P
R4X1P
R4X2P
R1542
DSCL1
HECN
HECP
0.1u
*C1561 10K
1000P
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
C1519
1u 10V
CKZ
C1505 C1526
0.1u 0.1u C1564
10V 10V 1000P
*C1555 C1533 R1629
GND_A 10u 1u 10V 10K
B *C1549
10u R1521 R1522
R1525
10V
KZA616WJQZ
CKZ
R1621
1K
10V 51 F 51 F F R1527 C1554
75
KZA616WJQZ 75 F 0.1u
10V
C1518 C1516 C1550
0.1u 0.1u
1000P
A192WJ
10V
FB1515
10V
*C1563
1000P
3
C1521
5.1
5.1
5.1
R1531 TO MAIN2(TERMINAL)
5.1
1u 10V
5.1
5.1
10
5.1
5.1
VGA_PWR5V 002
VGA_PWR5V
R1614
R1615
R1610
R1611
4
VGA_SCL 002
R1616
R1617
VGA_SCL
R1612
R1613
VGA_SDA 002
HDMI1_CLKN_222.75MHz
HDMI1_CLKP_222.75MHz
VGA_SDA
HDMI4_HPG
HDMI4_SDA
HDMI4_SCL
HDMI1_D2N
HDMI1_D0N
HDMI1_D1N
HDMI1_D0P
HDMI1_D1P
HDMI1_D2P
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2–6
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit-3 (LC-40/46/52/60LE830U/832U/LC-60LE831U) MAIN3(HDMI)
J D1511
1SS184
SC1505 D1517
1 HDMI4
ZA264WJQZ 1SS184
3
DUNTKF733WE** 21 1
SC1501 2 20
HDMI3 2 4 6 8 10 12 14 16 18
ZA264WJQZ 3
11 13 15 17 19 2
20 21 1 3 5 7 9
22 23
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17 19 TL1512
22 23
HDMI3_POW5V
TP1510
TP1507
TP1506
TL1511 TL1513
TP1504
TP1505 R1536 TO MAIN7(UCOM)
TL1501 TL1510 0 007
HDMI_CEC_ HDMI_CEC_
TP1501
HDMI_CEC
TL1506 HDMI3_HPG
VA1501
VA1503
VXA074WJ IC1506 TO MAIN4(CPU)
VXA074WJ 39V
39V CM123408
1.1pF
I 1.1pF
004
HDMI_OPT_OUT
HDMI4_CLKN_222.75MHz
OUT4-
8
IN4-
IC1501 HDMI4_CLKP_222.75MHz
VA1509
VA1510
VXA074WJ
OUT4+ VXA074WJ 39V
CM123408 39V
10
IN4+
7
1.1pF
1.1pF
HDMI3_CLKN_222.75MHz HDMI4_D0N
OUT4- OUT3-
11
8
6
IN4- IN3-
L1501
HDMI3_CLKP_222.75MHz HDMI4_D0P
OUT4+ OUT3+ FA228WJ
TO MAIN4(CPU)
10
12
IN4+ IN3+
5
SW_TMDS_CLKN_222.75MHz_
HDMI3_D0N HDMI4_D1N 4 3 SW_TMDS_CLKN_222.75MHz
OUT3- OUT2- 004
11
13
6
4
IN3- IN2-
SW_TMDS_CLKP_222.75MHz_
1 2 SW_TMDS_CLKP_222.75MHz
L1502 004
HDMI3_D0P HDMI4_D1P FA228WJ
OUT3+ OUT2+
12
14
IN3+
3
IN2+ SW_TMDS_D0N_
8
R1561
HDMI3_D1N 47K HDMI4_D2N 4 3 SW_TMDS_D0N
OUT2- OUT1- 004
IN1-
13
15
4
2
IN2- VRK
SW_TMDS_D0P_
D1512 1 2 SW_TMDS_D0P
L1503 004
1SS420
H
7
HDMI3_D1P HDMI4_D2P FA228WJ
OUT2+ OUT1+ IN1+
14
16
3
1
IN2+ SW_TMDS_D1N_
HDMI4_HPG
R1507
HDMI3_D2N 4 3 SW_TMDS_D1N
OUT1- 27K 004
IN1-
15
HDMI4_SDA SW_TMDS_D1P_
1 2 SW_TMDS_D1P
HDMI_CEC_ L1504 004
HDMI4_SCL
HDMI3_D2P FA228WJ
OUT1+ IN1+
16
HDMI4_POW5V
SW_TMDS_D2N_
R1540
4 3 SW_TMDS_D2N
HDMI3_SDA 10 004
D1508 SW_TMDS_D2P_
HDMI3_SCL 1 2 SW_TMDS_D2P
1SS184 004
SC1502 2
HDMI2
ZA264WJQZ
20 21
2 4 6 8 10 12 14 16 18
TO MAIN10(POWER SUPPLY)
1 3 5 7 9 11 13 15 17 19
22 23
010
HDMI2_POW5V BU+3.3V
G C1515 010
A192WJ
FB1505
A192WJ
0.1u C1517 C1557 D+3.3V
FB1538
10V 1000P 0.1u *C1558
TP1508
10V 1000P
SW_TMDS_D0N_
SW_TMDS_D1N_
SW_TMDS_D2N_
TP1511
SW_TMDS_D0P_
SW_TMDS_D1P_
SW_TMDS_D2P_
010
D+5V
TL1502 TL1507
TP1502
SW_TMDS_CLKN_222.75MHz_
SW_TMDS_CLKP_222.75MHz_
010
M+1.8V
TL1505 TL1546
HDMI2_HPG
*C1546 C1547 *C1562 *C1551 C1553 *C1566
VA1504 10u 1000P 10u 1000P *C1556
VA1502 0.1u 0.1u
VXA074WJ 10V 10V 10u
VXA074WJ 10V 10V
39V KZA616WJQZ KZA616WJQZ 10V
39V C1548 *C1552
1.1pF KZA616WJQZ
1.1pF 0.1u C1541
10u *C1542
10V 10V 10u 0.1u
KZA616WJQZ 10V 10V
KZA616WJQZ 5 4
D1501
EXA705WJQZ
IC1502 VOUT VIN
CM123408
8.2V
R1509
IC1509
HDMI2_CLKN_222.75MHz S172B12U
OUT4- 4.7K
9
IN4-
ON GND NC
OUT4+ HDMI2_CLKP_222.75MHz 1 2 3
10
IN4+
7
TO MAIN6(FLASH)
F OUT3- HDMI2_D0N
R1554
10K R1619 100K 006
SCL1
11
IN3-
R1568 5.1
HDMI4_CLKN_222.75MHz R1623 100K 006
SDA1
OUT3+ HDMI2_D0P R1571 5.1
100
80
79
78
77
76
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
HDMI4_CLKP_222.75MHz
12
IN3+
5
C1523
1u 10V
R1572 5.1
HDMI4_D0N
TXCN
CKZ
TXCP
TX0N
TX1N
TX2N
TX0P
TX1P
TX2P
R1XCN
R1XCP
R0XCN
R0XCP
RSVDL
RSVDL
R0X2N
R0X1N
R0X0N
VDD33
VDD12
R0X2P
R0X1P
R0X0P
Q1510 *R1563
AVDD12
HDMI2_D1N
TVDD12
2
OUT2- HDMI2_POW5V *R1562
R1512 R1573 5.1
13
TPWR_CI2CA
4
IN2- R3PWR5V 0
SSM6N15FU
75
1
HDMI4_D0P 0
47K R1X0N R1555
VRK 10
OUT2+ HDMI2_D1P HDMI2_HPG
14
IN2+ R1X0P
74
2
1
CBUS_HPD3
6
OUT1- HDMI2_D2N
IN1- R1X1N R1541
15
73
DSCL3
3
R1574 5.1 10 VRK
HDMI4_D1N
5
2
HDMI2_SCL
HDMI2_D2P R1575 5.1
OUT1+ IN1+ HDMI4_D1P 8 7
R1X1P DSDA3
16
72
4
HDMI2_SDA
R1576 5.1 6 5
HDMI2_SDA HDMI4_D2N
4
3
D1509 HDMI2_SCL R1577 5.1 R1X2N CSCL 4 3
71
5
HDMI4_D2P
1SS184
2 1
1 R1X2P
E CSDA
70
6
SC1503
HDMI1 ZA264WJQZ 3
C1511
2 0.1u 10V R1565 4.7K
20 21 VDD33 TP1519
C1512
69
7
2 4 6 8 10 12 14 16 18 GPIO1 R1533
1000P R1566 4.7K
10K
*C1510
1 3 5 7 9 11 13 15 17 19 10u
22 23 R2XCN TP1520
10V GPIO0
68
8
R1581 5.1 R1534
HDMI3_CLKN_222.75MHz KZA616WJQZ
HDMI1_POW5V 10K R1514
R1583 5.1 10K
TP1512 HDMI3_CLKP_222.75MHz R2XCP
R1595 INT
67
9
TP1509
1K R1585 5.1
TL1508 HDMI3_D0N
R1597 5.1 R2X0N CEC_A TP1518 R1538
66
10
HDMI3_D0P 10K
TL1503 TL1504
*R1584
TP1503
*C1538 10
TL1535 10u 10V VGA_PWR5V
R2X0P R5PWR5V(VGA) KZA616WJQZ
65
11
C1540
C1539 1u 10V CKZ
R1589 VA1508 0.1u 10V
VA1506 R2X1N SBVCC5
4.7K VXA074WJ
64
12
*C1565
VXA074WJ
39V
39V
1.1pF
*R1519
0
HDMI3_D1N
R1598 5.1
IC1504 1000P
R1524 10 R1545 0
1.1pF
SII9387
IC1503 HDMI3_D1P
R1599 5.1
R2X1P
HDMI_RSVD
63
13
CM123408 R1600 5.1
HDMI3_D2N
D OUT4-
HDMI1_CLKN_222.75MHz
R2X2N 3
VGA_SCL
9
R1601 5.1 DSCL5(VGA) 4
8
IN4-
62
14
HDMI3_D2P *R1537
HDMI1_SDA 10 VGA_SDA
1 2
HDMI1_CLKP_222.75MHz
OUT4+ R1553
DSDA5(VGA)
10
IN4+
7
R2X2P
61
15
10K
HDMI1_SCL C1513 R1556 FB1512
HDMI1_D0N 0.1u 10V 10 HDMI1_POW5V
OUT3- A192WJ
VDD33
11
IN3- C1514 R4PWR5V
60
16
1000P
C1522 Q1508
*C1543 1u 10V
HDMI1_D0P 2SA2061
OUT3+ 10u R3XCN CKZ
12
IN3+ CBUS_HPD4
5
10V
59
17
HDMI2_CLKN_222.75MHz
R1602 5.1 KZA616WJQZ 3.2 3.3
R1567
HDMI1_D1N 0
OUT2- R1603 5.1 HDMI1_SCL
HDMI2_CLKP_222.75MHz R3XCP 3 4
13
IN2- DSCL4
58
18
R1569
R1582
R1604 5.1 HDMI1_SDA 2.5 10K
HDMI2_D0N 10
1 2
HDMI1_D1P
OUT2+
R1605 5.1 R3X0N DSDA4 R1551
14
IN2+
57
19
HDMI2_D0P 10K
R1552
OUT1- HDMI1_D2N 10 HDMI3_POW5V
IN1- R3X0P R2PWR5V R1558 Q1509
15
56
20
330 RT1N141U
C1520
HDMI1_D2P 1u 10V
OUT1+ IN1+ CKZ HDMI3_HPG
R3X1N
16
CBUS_HPD2
55
21
C HDMI2_D1N
R1606 5.1
R1607 5.1 R3X1P HDMI3_SCL
HDMI2_D1P 3 4
DSCL2
54
22
R1608 5.1 HDMI3_SDA
HDMI2_D2N 1 2
R1543
R1609 5.1 R3X2N DSDA2 10
53
23
HDMI2_D2P
MICOM_VCC33
R3X2P *C1531
52
24
10u 10V
C1544 R1557
AVDD12 KZA616WJQZ 10
CBUS_HPD0
0.1u
CBUS_HPD1
ETH_RX1N HDMI4_POW5V
ETH_RX1P
ETH_TX1N
ETH_TX1P
R0PWR5V
SPDIF_IN
R1PWR5V
EPWR33
51
25
C1545
DSDA0
R4XCN
R4X0N
R4X1N
R4X2N
VDD33
VDD12
DSCL0
R4XCP
DSDA1
R4X0P
R4X1P
R4X2P
R1542
DSCL1
HECN
HECP
0.1u
*C1561 10K
1000P
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
C1519
1u 10V
C1505 C1526
C1564 CKZ
0.1u 0.1u 1000P
10V 10V
C1533 R1629
GND_A 1u 10V 10K
CKZ
B *C1549
10u
10V
R1521 R1522
51 F
R1525
75 F
R1527
75 F
R1621
1K
51 F C1554
KZA616WJQZ
0.1u *C1555
10V 10u
C1550 10V
C1518 C1516 KZA616WJQZ
0.1u 0.1u
1000P
10V 10V
*C1563
1000P
3
A192WJ
FB1515
C1521
5.1
5.1
R1531 TO MAIN2(TERMINAL)
5.1
5.1
1u 10V 10
VGA_PWR5V 002
VGA_PWR5V
R1614
R1615
5.1
5.1
5.1
5.1
R1610
R1611
4
VGA_SCL 002
VGA_SCL
VGA_SDA 002
HDMI1_CLKN_222.75MHz
HDMI1_CLKP_222.75MHz
VGA_SDA
R1612
R1613
R1616
R1617
HDMI4_HPG
HDMI4_SDA
HDMI4_SCL
HDMI5_HPG
HDMI1_D2N
HDMI1_D0N
HDMI1_D1N
HDMI1_D0P
HDMI1_D1P
HDMI1_D2P
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2–7
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit-4 (LC-40/46/52/60LE835U)
MAIN4 (CPU)
*R3422
*R3423
J TO MAIN10(POWER SUPPLY) FB3301
A192WJ 2.2K
2.2K
010 CPU_BU+3.3V
TO MAIN12(LAN_USB)
STB+3.3V
*L3301 TO MAIN11(DEMOD_CI)
*C3322 C3323 C3326 CPU_DATMDI_RJ45_TP
10uH CRM CPU_DATMDI_RJ45_TP
10u 0.01u 0.01u CPU_A3.3V CPU_OS_CLK2 *R3431 220 011 012
CKZ CZB CZB TU_DEMOD_SCL CPU_DATMDI_RJ45_TN
CPU_DATMDI_RJ45_TN
*C3347 C3348 CPU_OS_DAT2 *R3430 220 011 012
010 TU_DEMOD_SDA
D+3.3V 10u 0.1u TP3323 CPU_DATMDI_RJ45_RP
FB3302 CPU_DATMDI_RJ45_RP
C3303 C3306 C3307 16V CZB DVB_SPI_CLK1 012
A192WJ CPU_AVDD3.3V KZA837WJQZ
0.01u 0.01u 0.01u 10V CPU_DATMDI_RJ45_RN
CPU_DATMDI_RJ45_RN
CZB CZB CZB 012
010
M+1.8V
LAN_LED0 TP3355
LAN_LED1 TP3356
C3324 C3328 C3329
010 0.1u 0.1u 0.1u C3338 C3341 C3343 C3345
D+1.1V C3340 C3342 C3344
1u 0.01u 0.01u 0.01u C3346
TO MAIN5(DDR) 16V 16V 16V 0.01u 0.01u 0.01u 0.01u
C3320
005 C3318 4.7u LDM_CLK
D+1.5V 2 1 2 1 2 1 C3331 C3333 C3335 C3337 TP3340
4.7u 10V
C3304 10V C3332 C3334 C3336 4.7u
KZA761WJQZ 0.1u 0.1u 0.1u LDM_CS
4.7u 0.1u 0.1u 0.1u 10V TP3341
KZA761WJQZ 4 3 4 3 4 3 KZA761WJQZ
10V
TO MAIN11(DTV_CI) KZA761WJQZ C3305
C3308
C3309
C3310
C3312
C3313
C3315
C3316
LDM_DI TP3342
1u 0.01u 0.01u 0.01u 6 5 6 5 6 5
011 0.01u 0.01u 0.01u 0.01u
CPU_A+1.2V C3396 MT5135_INT 011 LDM_DO
MT5135_INT TP3343
0.1u
8 7 8 7 8 7
LDM_VSYNC TP3344
TL3301
I
TO MAIN6(FLASH)
5 4 *C3302
10u 10V
VOUT VIN KZA616WJQZ SD_CMD 006
SD_CMD
IC3301 SD_D0 006
SD_D0
S172B12U SD_D1 006
SD_D1
ON GND NC C3321 LVDS0_D1P LVDS0_CLKP_74MHz LVDS0_D4P *R3432 *R3365 SD_D2 006
0.01u LVDS0_D0P LVDS0_D2P LVDS0_D3P SD_D2
0 SB1FF SB1FF 0
1 2 3 NC NC NC NC NC NC NC NC
DEMOD_TSCLK SD_D3 006
011 SD_D3
R3307 A1 A2 A3 A4 A6 A7 A8 A10 A11 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 ATSC_TS_CLK
1
2
7
TO MAIN5(DDR) 330 F
C3301 DEMOD_TSVAL 011
0.1u ATSC_TS_VAL
3
4
LVDS0_D1N LVDS0_CLKN_74MHz LVDS0_D4N
5
10V LVDS0_D0N LVDS0_D2N LVDS0_D3N
005 RVREF6 DEMOD_TSSYNC 011
A_DDR_RESET NC NC NC NC NC NC NC NC ATSC_TS_SYNC
TO MAIN8(PANEL)
5
6
3
005 B1 B2 B3 B4 B6 B7 B8 B10 B11 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 DEMOD_TSDATA0 011
008 A_DDR_CS0# R3308 ATSC_TS_D0
7
8
LVDS0_D0N
1
005 330 F
008 A_DDR_RAS#
LVDS0_D0P
005 LVDS1_D0N LVDS1_D2N LVDS1_D3N
008 A_DDR_CAS#
C3319 NC NC NC
TO MAIN1(TUNER)
LVDS0_D1N
005 0.01u
008 A_DDR_WE# C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C17 C19 C21 C23 C25 C27 C29 C30 C31 C32
LVDS0_D1P CPU_U2RX SD_DET
005 PNL_POW SD_WP
008 A_DDR_ODT
LVDS0_D2N
H LVDS0_D2P
008 A_DDR_CLKEN
005 R3312 56 LVDS1_D0P LVDS1_D2P LVDS1_D3P
NC NC NC
RVREF6
005
008 A_DDR_BA0 C3325
LVDS0_CLKN_74MHz D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D13 D14 D15 D17 D19 D21 D23 D25 D27 D29 D30 D31 D32
005 0.01u
RVREF6 CPU_U2TX STB_CPU LDM_DO
008 A_DDR_BA1 CVBS_OUT_MUTE
LVDS0_CLKP_74MHz
005 LVDS1_D1P LVDS1_CLKP_74MHz LVDS1_D4P
008 A_DDR_BA2 LVDS1_D1N LVDS1_CLKN_74MHz LVDS1_D4N
LVDS0_D3N
NC NC NC NC NC NC
008 DEMOD_RST *R3356 0 011
LVDS0_D3P E3 E4 E5 E6 E7 E8 E9 E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20 E22 E23 E24 E25 E26 E27 E28 E29 E30 E31 E32 ATSC_DEMOD_RST
005
008 A_DDR_A0 A_DDR_DQ22 N_TUN_SAT_RST LDM_CLK
LAMP_ERR_CPU LDM_CS
LVDS0_D4N A_DDR_DQ20 R3352
005 R3344 12K
008 A_DDR_A1
10K
F
R3424
LVDS0_D4P 4.7K
005
008 A_DDR_A2
LVDS1_D0N
005 F1 F2 F3 F6 F7 F9 F10 F13 F14 F18 F19 F20 F21 F22 F23 F28 F29 F30 F31 F32
008 A_DDR_A3 A_DDR_DQM3 A_DDR_DQ18 LDM_DI LDM_VSYNC
LVDS1_D0P A_DDR_DQ16 CVBS1_PLUG
005 CPU_IF_AGC 001
008 A_DDR_A4 CPU_IF_AGC
LVDS1_D1N
005
008 A_DDR_A5
LVDS1_D1P
005 G1 G2 G3 G4 G5 G7 G14 G24 G26 G30 G31 G32
008 A_DDR_A6
LVDS1_D2N A_DDR_DQS2N A_DDR_DQM2 A_DDR_DQ27 CPU_LED CVBS2_PLUG
005 R3327 47 UCOM_RST C3394
A_DDR_DQS2P A_DDR_DQ29 CPU_ATV_IF+ R3440 001
008 A_DDR_A7 CPU_ATV_IFP
LVDS1_D2P 0.01u 0
005 CPU_ATV_IF- C3395
A_DDR_A8 R3443 001
008 CPU_ATV_IFN
LVDS1_CLKN_74MHz 0.01u 0
005
008 A_DDR_A9 H1 H2 H3 H4 H5 H6 H8 H14
LVDS1_CLKP_74MHz A_DDR_DQS3N A_DDR_DQ25
005
008 A_DDR_A10 A_DDR_DQS3P A_DDR_DQ31 R3329 47
LVDS1_D3N
G LVDS1_D3P
008 A_DDR_A11
005
005
0
008 A_DDR_A12
LVDS1_D4N J1 J2 J6 J8 J14 J30 J31 J32
R3439
005 COMP2_PLUG
008 A_DDR_A13
A_DDR_DQ19 UCOM_MODEN_CPU_USB1_FLG
A_DDR_DQ17
LVDS1_D4P
005
A_DDR_MCLK0P_621MHz
005 K1 K2 K4 K6 K28 K29 K30 K31 K32
A_DDR_MCLK0N_621MHz A_DDR_DQ21 TCON_ROM_EN CPU_GPIO13CPU_USB1_EN S1_PLUG
CPU_GCK5
A_DDR_DQ23
D3318
005
2
A_DDR_MCLK1P_621MHz A192WJ 1SS226
3
005 FB3303
A_DDR_MCLK1N_621MHz L1 L2 L3 L4 L5 L6 L7 L11 L12 L13 L14 L15 L16 L22 L23 L27 L28 L29 L30 L31 L32
1
A_DDR_MCLK1N_621MHz A_DDR_DQ24 A_DDR_DQ30 N_TUN_RST SD_D2 COMP1_PLUG
AMP_PROTECT SD_D3
005 A_DDR_MCLK1P_621MHz A_DDR_DQ26 A_DDR_DQ28
A_DDR_DQM0
2
D3319
005
A_DDR_DQM1 1SS226
3
005 M3 M4 M5 M11 M12 M13 M14 M15 M16 M17 M19 M20 M22 M23 M28 M30
1
A_DDR_DQM2
A_DDR_ODT A_DDR_CLKEN TUN_GAIN_SW SD_D1
005
A_DDR_DQM3
A_DDR_CAS#
*IC3303 D3320
2
1SS226 C3375 R3395
005
A_DDR_DQS0P IXD220WJQZ 0.01u 68
3
PC_RP 002
005 PC_RED
1
A_DDR_DQS0N N1 N2 N3 N4 N5 N6 N11 N12 N13 N14 N15 N16 N17 N18 N19 N20 N21 N23 N27 N28 N29 N30 N31 N32 C3360 R3367
PC_GP 002
005 A_DDR_A13 A_DDR_A0 A_DDR_A10 HP_PLUG SP_MUTE SD_CMD PC_GREEN
AC_DET_CPU SD__CLK SD_D0 0.01u 68
A_DDR_DQS1P A_DDR_A3 A_DDR_WE#
2
D3327 PC_SOG C3356 R3372
005 QZ Not use SRS
F 1SS226
3
A_DDR_DQS1N 1500P 0
PC_BP C3357 R3362 002
N1 Use SRS PC_BLUE
1
005 0.01u 68
A_DDR_DQS2P
P1 P2 P3 P4 P5 P6 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P28 P29 P30 P31 P32 PC_VGACOM C3358 R3363 002
005 A_DDR_A9 A_DDR_A7 A_DDR_BA1 DVB_SPI_CLK1 PC_RGB_COM
A_DDR_DQS2N 0.01u 100
A_DDR_RESET A_DDR_A2 A_DDR_A12 MT5135_INT PC_HSYNC 002
005 D3322 PC_HSYNC
A_DDR_DQS3P
2
1SS226 PC_VSYNC 002
005 PC_VSYNC
3
A_DDR_DQS3N
R3 R4 R5 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R26 R27 R28 R29 R31 R32
1
A_DDR_A5 A_DDR_A11
005 A_DDR_BA0
A_DDR_DQ0
2
D3328
005 SC_Y0P C3361 R3381 002
1SS226
3
A_DDR_DQ1 BLUE1
0.01u
68
1
005 T1 T2 T3 T4 T5 T6 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T27 T28 T29
A_DDR_DQ2 SC_SOY0 R3382 002
A_DDR_CS0# A_DDR_BA2 A_DDR_A6 SC1FSW
005 D3323
A_DDR_DQ3 A_DDR_RAS# A_DDR_A8 0
2
1SS226 C3363
SC_PB0P R3373 002
005 GREEN1
3
A_DDR_DQ4 A_DDR_DQ6 A_DDR_A1 DEMOD_RST 0.01u
A_DDR_DQ4 A_DDR_A4 RVREF5 DEMOD_TSDATA0 DEMOD_TSCLK 68
1
005
A_DDR_DQ5 U1 U2 U3 U4 U5 U7 U11 U12 U13 U14 U15 U16 U17 U18 U19 U20 U21 U22 U28 U29 U30 U31 U32 SC_PR0P C3364 R3374 002
RED1/C1
005 0.01u
2
A_DDR_DQ6 D3329 68
1SS226 C3365 R3375
3
005 SC_COM0 002
A_DDR_DQ7 C3330 CPU_AOSDATA0 SC_RGB_COM
A_DDR_DQ0 DEMOD_TSVAL CPU_OS_DAT2 0.01u
1
005 A_DDR_DQ2 0.01u CPU_ALIN CPU_AOSDATA1 DEMOD_TSSYNC CPU_OS_CLK2 100
A_DDR_DQ8
V1 V2 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 V22 V26 V27 V28 V29 V30 V31 V32
005
TO MAIN6(FLASH) A_DDR_DQ9 D3304
COMP_Y1P C3366 R3383 002
2
1SS226 COMP1_Y
006 005 0.01u
E FLASH_CE0# A_DDR_DQ10 68
3
C3367 R3384
CPU_IF_AGC COMP_SOY1 002
005 A_DDR_DQM1 A_DDR_DQ13 DSUB_WP COMP1_SOY
1
A_DDR_DQ11 1500P
006 W1 W3 W4 W5 W11 W12 W13 W14 W15 W16 W17 W18 W19 W20 W21 W22 W23 W29 W30 0
NAND_CE1# 005 C3368
A_DDR_DQ12 COMP_PB1P R3376 002
2
006 D3324 COMP1_Pb
NAND_RB# 005 0.01u
1SS226 68
3
A_DDR_DQ13
006 COMP_PR1P C3369 R3377 002
NAND_ALE CPU_AOSDATA3 CPU_AOLRCK CPU_AOMCLK
1
005 A_DDR_DQS0P A_DDR_DQ11 COMP1_Pr
A_DDR_DQ14 A_DDR_DQS0N A_DDR_DQM0 A_DDR_DQ15 CPU_AOSDATA4 CPU_AOSDATA2 CPU_AOBCK 0.01u
006 68
NAND_CLE 005 Y1 Y2 Y3 Y4 Y6 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y20 Y21 Y22 Y27 Y28 Y29 Y30 Y31 Y32 D3307
A_DDR_DQ15 C3370 R3378
2
1SS226 COMP_COM1 002
006 COMP1_COM
NAND_WE# 005 0.01u
3
A_DDR_DQ16 100
006
NAND_OE#
1
005 A_DDR_DQ14 C3371
A_DDR_DQ17 CPU_OPWM2 CPU_OS_DAT0 CPU_ASPDIF ANALOG_CPU_SY0 R3370 R3412 002
A_DDR_DQ12 A_DDR_DQ9 CPU_OPWM0 LAN_LED1 CPU_OS_CLK0 0.047u
ANALOG_SY0
006 005 AA3 AA4 AA5 AA11 AA12 AA13 AA14 AA15 AA16 AA17 AA18 AA19 AA20 AA21 AA22 AA26 AA27 AA28 AA29 AA30 AA31 AA32 10V 100 0
2
NAND_D0 A_DDR_DQ18 D3325
C3372 R3413
1SS226
3
006 005 ANALOG_CPU_SC0 0.047u R3371 002
NAND_D1 A_DDR_DQ19 ANALOG_SC0
10V 100 0
1
006 005 R3347 R3349
NAND_D2 A_DDR_DQ20 A_DDR_DQS1P A_DDR_DQ10
A_DDR_DQS1N A_DDR_DQ1 A_DDR_DQ8 LAN_LED0 CPU_SY1 TP3321
006 005 F 12K F
12K
NAND_D3 A_DDR_DQ21 AB1 AB2 AB3 AB4 AB5 AB6 AB11 AB12 AB13 AB14 AB15 AB16 AB17 AB18 AB19 AB20 AB21 AB22 AB28 AB29 AB30 D3321 CPU_SC1 TP3322
2
006 005 CPU_OS_DAT1 1SS226
NAND_D4 A_DDR_DQ22 CPU_OS_CLK1 C3373 R3414
3
CPU_CVBS0P R3379 001
006 005 D3305 TUNER_CVBS
NAND_D5 A_DDR_DQ23 0.047u 100 0
1
A_DDR_DQ7 EXA697WJQZ
006 005 A_DDR_DQ3 A_DDR_DQ5 CPU_U1TX CPU_U1RX CPU_OPWM1 R3415
CPU_CVBS1P 5.6V C3374 R3380 002
NAND_D6 A_DDR_DQ24 CVBS1_IN
AC1 AC2 AC3 AC4 AC12 AC13 AC15 AC17 AC19 AC20 AC21 AC27 AC28 AC29 AC30 AC31 AC32
2
D3326 D3306 0.047u 100 0
006 005
NAND_D7 A_DDR_DQ25 1SS226
3
EXA697WJQZ
CPU_CVBS2P C3388 R3311 R3330 002
005 5.6V SC/Y_CVBS2_IN
1
D A_DDR_DQ26
A_DDR_DQ27
005 CPU_GPIO7 CPU_GPIO8 CPU_DATMDI_RJ45_TN
CPU_DATMDI_RJ45_TP
D3330
EXA697WJQZ
0.047u 100 0
5.6V
AD3 AD4 AD5 AD26 AD27 AD28 AD30 AD31 AD32
TO MAIN12(LAN_USB) 005
A_DDR_DQ28
CPU_CVBSCOM 002
012 005 CVBS_COM
USB_D0P A_DDR_DQ29 C3359
012 005 A_DDR_MCLK0P_621MHz 1u
USB_D0N A_DDR_DQ30 A_DDR_MCLK0N_621MHz CPU_DATMDI_RJ45_RP
CPU_DATMDI_RJ45_RN CPU_BYPASS0 TP3324
012 005 AE1 AE2 AE4 AE9 AE10 AE14 AE25 AE26 AE27 AE30 AE31 AE32
USB_D1P A_DDR_DQ31 CPU_BYPASS1 TP3325
OPCTRL0 C3355
012
USB_D1N 0.01u
CPU_VDAC2_OUT TP3327
NC NC
*C3392 0.1u
TO MAIN3(HDMI) AF1 AF2 AF3 AF8 AF9 AF10 AF12 AF13 AF14 AF16 AF17 AF18 AF19 AF20 AF22 AF23 AF25 AF26 AF27 AF28 AF29 AF30 AF31 AF32 CPU_SIF 001
SIF
CPU_SIF_COM C3393
003 OPCTRL6 OPWRSB CPU_VGA_SCL KEY1_CPU KEY2_CPU QSTEMP_CPU CPU_SIF
SW_TMDS_D0P R3354 0 0.1u
003
SW_TMDS_D0N CPU_ADACL2
PM_REQ CPU_ADACR2
003
330
SW_TMDS_D1P AG1 AG2 AG3 AG4 AG5 AG8 AG10 AG12 AG13 AG14 AG16 AG17 AG19 AG20 AG23 AG26 AG27 AG28 AG29 AG30 AG31 AG32
003 OPCTRL1 CPU_VGA_SDA R3434 SLOWSW2 SLOWSW1
SW_TMDS_D1N CPU_SIF_COM COMP1_AINL1 002
R3387 *C3378
R3353
COMP1_IN_L
003 D3310 30K 10u 16V
SW_TMDS_D2P EXA713WJQZ
1K
EJTAG_TDI COMP1_AINR1 R3388 *C3379 002
EJTAG_TDO EJTAG_TMS CPU_ADACL3 12V COMP1_IN_R
003
1K
D3311 30K 10u 16V
*R3350
0
SW_TMDS_D2N
0
AH1 AH2 AH3 AH4 AH6 AH7 AH8 AH10 AH12 AH13 AH14 AH16 AH17 AH20 AH23 AH24 AH26 AH27 AH28 AH29 AH30 EXA713WJQZ
C3387 CVBS1_AINL2 R3389 *C3380 002
R3435
003 F 12V CVBS1_IN_L
R3417
SW_TMDS_CLKP_222.75MHz I2C_READY ANT+5V_SW_CPU HP_MUTE CPU_U0TX OPC_CPU R3418 0 0.01u D3312 30K 10u 16V
R3333 5.1K R3339 C3351 EXA713WJQZ
003 0 1u *C3353 CVBS1_AINR2 12V R3390 *C3381 002
C3354
C SW_TMDS_CLKN_222.75MHz
TP3301 HDMI_CEC_CPU NAND_WE# NAND_D5 SMPOWHOLD HDMI_CEC_CPU
ORESET#
C3386
CPU_BYPASS1 CPU_CVBS1P
C3349
1u 2.2u 1u
CPU_ADACR3
HP_MON_L
HP_MON_R CVBS2_AINL3
D3313
EXA713WJQZ
12V
30K
R3391
10u
*C3382
16V
002
CVBS1_IN_R
C3339 CVBS_IN2_L
AJ3 AJ4 AJ5 AJ6 AJ8 AJ9 AJ10 AJ11 AJ12 AJ13 AJ17 AJ18 0.01u AJ20 AJ21 AJ22 AJ23 AJ24 AJ25 AJ26 AJ27 AJ28 AJ29 AJ30 AJ31 AJ32 D3314 30K 10u 16V
TO MAIN12(LAN_USB) 4.7u EXA713WJQZ
012 N_USB_RST N_FRC_RST DET_PNL_12V_CPU POW_SW_CPU OPCTRL5 CPU_U0RX 10V COMP_COM1 COMP_PR1P CPU_BYPASS0 CVBS2_AINR3 12V R3392 *C3383 002
N_USB_RST PC_HDMI_AINR4 CVBS_IN2_R
KZA761WJQZ D3315 30K 10u 16V
EXA713WJQZ
TO MAIN6(FLASH) NAND_CLE
PC_HDMI_AINL4 12V R3393 *C3384 002
PC_HDMI_L
006 NAND_ALE NAND_OE# NAND_D4 NAND_D6 N_USB_RST N_KEY_RST_CPU ANALOG_CPU_SC0 CPU_CVBSCOM COMP1_AINL1 CVBS2_AINR3 COMP1_AINR1 D3316 30K 10u 16V
SMPOWHOLD EXA713WJQZ
AK1 AK2 AK3 AK4 AK5 AK6 AK7 AK8 AK9 AK10 AK11 AK12 AK13 AK14 AK15 AK16 AK17 AK18 AK19 AK20 AK21 AK22 AK23 AK24 AK25 AK26 AK27 AK28 AK29 AK30 AK31 AK32 PC_HDMI_AINR4 12V R3394 *C3385 002
PC_HDMI_R
D3317 30K 10u 16V
TO MAIN7(UCOM) PNL_WP PNL_EN PNL_I2C_EN OPCTRL4 PC_BP PC_SOG PC_GP COMP_PB1P SC_PR0P CPU_VDAC2_OUT CPU_CVBS2P EXA713WJQZ
007 SMPOWHOLD CPU_CVBS0P 12V
SMPOWHOLD TO_MAIN9(AUDIO_AMP)
TP3358
NAND_D0 SW_TMDS_CLKP_222.75MHz ATV_AINL5
CVBS2_AINL3 ATV_AINL5 CVBS1_AINL2 ATV_AINR5 CVBS1_AINR2
FLASH_CE0# NAND_D2 NAND_D7 USB_D1P USB_D0P SW_TMDS_D0P SW_TMDS_D2P ATV_AINR5
TP3359
F
007 PM_REQ AL1 AL2 AL3 AL5 AL6 AL7 AL9 AL10 AL11 AL12 AL13 AL15 AL16 AL18 AL19 AL21 AL22 AL24 AL26 AL27 AL29 AL30 AL31 AL32
PM_REQ CPU_AINL6 TP3319
SW_TMDS_D1P PC_HSYNC PC_VGACOM COMP_SOY1 SC_SOY0 SC_COM0 CPU_SC1 CPU_ATV_IF-
TP3302
560
N_KEY_RST_CPU CPU_AINR6 TP3320
R3343
NAND_D1 SW_TMDS_CLKN_222.75MHz
NAND_RB# NAND_D3 NAND_CE1# USB_D1N USB_D0N SW_TMDS_D0N SW_TMDS_D2N PC_HDMI_AINL4 CPU_AINL6 CPU_AINR6
AM1 AM2 AM3 AM5 AM6 AM7 AM9 AM10 AM11 AM12 AM13 AM15 AM16 AM18 AM19 AM21 AM22 AM24 AM26 AM27 AM29 AM30 AM31 AM32 CPU_AOLRCK R3359 009
SP_LRCLK
47 FB3304
SW_TMDS_D1N PC_VSYNC PC_RP COMP_Y1P SC_Y0P SC_PB0P ANALOG_CPU_SY0 CPU_SY1 CPU_ATV_IF+ 1043CE
CPU_AOBCK R3360 009
SP_BCLK
220
CPU_AOSDATA0 R3361 009
SP_DATA
47
CPU_AOSDATA1 TP3330
CPU_AOSDATA2 TP3331
B CPU_AOSDATA3
CPU_AOSDATA4
TP3332
TP3333
TO_MAIN9(AUDIO_AMP)
NC
1 3 5 7 HP_MON_L R3401 C3362 009
R3305 HP_MONITOR_L
22K 1u 10V
SD_WP
R3346
2.2K
OPWRSB
1K
SLOWSW1
SLOWSW2
PNL_WP
SD_DET
DSUB_WP
PNL_EN
PNL_POW
OPC_CPU
HP_MUTE
SP_MUTE
ORESET#
HP_PLUG
OPCTRL4
OPCTRL5
OPCTRL0
OPCTRL1
UCOM_RST
UCOM_MODE
STB_CPU
CPU_LED
OPCTRL6
S1_PLUG
CPU_OPWM1
CPU_OPWM2
CPU_OPWM0
CPU_GCK5
CPU_U1RX
CPU_U0RX
CPU_U2RX
1M
CPU_U1TX
POW_SW_CPU
KEY1_CPU
KEY2_CPU
CPU_U0TX
CPU_U2TX
SB1FF HP_MON_R R3406 C3389 009
N_FRC_RST
N_TUN_RST
QSTEMP_CPU
COMP1_PLUG
COMP2_PLUG
CPU_GPIO7
CPU_GPIO8
TCON_ROM_EN
AC_DET_CPU
CVBS1_PLUG
CVBS2_PLUG
I2C_READY
AMP_PROTECT
CPU_VGA_SDA
CPU_GPIO13
CPU_VGA_SCL
HP_MONITOR_R
CPU_OS_DAT0
CPU_OS_DAT1
TUN_GAIN_SW
CPU_USB1_EN
CPU_OS_CLK0
CPU_OS_CLK1
LAMP_ERR_CPU
PNL_I2C_EN
CVBS_OUT_MUTE
ANT+5V_SW_CPU
22K 1u 10V
N_TUN_SAT_RST
4.7K
4.7K
R3351
N_CPU_USB1_FLG
DET_PNL_12V_CPU
2 4 6 8
R3345
X3301
R3320
R3323
10
NC
SCA237WJQZ
47
10
R3335
10
47
47
10
10K
4 NC 3
10
10
47
4.7K
4.7K
R3338
EJTAG_TDI
10
10
10
CPU_ADACL2
10K
10K
TP3334
R3433
R3340
10K
*R3310
R3321
R3324
R3337
R3436
*R3309
10K
TP3307
TP3311
TP3312
TP3357
TP3315
TP3316
10
R3325
R3313
R3314
CPU_ADACR2
10K
10K
TP3335
R3409
R3410
EJTAG_TDO
47
1 NC 2
R3421
R3348
C3350 C3352 CPU_ADACL3 TP3336
R3411
R3420
R3316
R3318
R3341
7P 27MHz
R3419
EJTAG_TMS
7P CPU_ADACR3 TP3337
50V D3303
50V
PXA018WJ
006
006
006
006
006
006
006
006
006
006
006
002
002
002
002
002
002
002
002
009
009
009
009
008
008
008
008
008
008
008
010
010
010
010
010
001
001
001
007
007
007
012
012
CPU_ASPDIF R3368 002
OPT_OUT
CPU_ALIN 47
TP3338
TP3308
TP3354
TO_MAIN3(HDMI)
TP3328
TP3326
CONFIG PIN
TP3314
TP3329
TP3345
TP3346
TP3347
TP3348
TP3350
TP3351
TP3352
TP3353
R3369 003
TO MAIN6(FLASH)
HDMI_OPT_OUT
47
TO MAIN9(AUDIO AMP)
TO MAIN12(LAN_USB)
TO MAIN2(TERMINAL)
TO_MAIN6(FLASH)
TO MAIN10(POWER)
TO MAIN1(TUNER)
TO MAIN7(UCOM)
R3398 006
TO MAIN8(PANEL)
CPU_UARXD1_UCOM
CPU_UATXD1_UCOM
TO MAIN6(FLASH)
CPU_A_SPDIF
N_CPU_USB1_FLG
47
CVBS_OUT_MUTE
CPU_UARXD0_RS
CPU_UATXD0_RS
N_TUN_SAT_RST
TCON_ROM_EN
AMP_PROTECT
A
TUN_GAIN_SW
CPU_USB1_EN
COMP1_PLUG
UCOM_MODE
CVBS1_PLUG
CVBS2_PLUG
PANEL_OFL1
PNL_I2C_EN
PNL_I2C_EN
DUNTKF733WE12
N_CPU_RST
N_PER_RST
N_FRC_RST
N_TUN_RST
UCOM_RST
I2C_READY
SDA0_400k
SCL0_400k
SLOWSW1
DSUB_WP
PNL_POW
HP_MUTE
SP_MUTE
HP_PLUG
STB_CPU
S1_PLUG
PNL_WP
SD_DET
AC_DET
PNL_EN
SD_WP
SDA1
SCL1
OFL1
OFL2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
2–8
LC-40/46/52/60LE835U/830U/832U/LC-60LE831U
MAIN Unit-4 (LC-40/46/52/60LE830U/832U/LC-60LE831U)
MAIN4 (CPU)
*R3422
J *R3423 2.2K
TO MAIN10(POWER SUPPLY) FB3301
2.2K
A192WJ
010 CPU_BU+3.3V
STB+3.3V TO MAIN12(LAN_USB)
L3301
*C3322 C3323 C3326 TO MAIN11(DEMOD_CI) CPU_DATMDI_RJ45_TP
10uH CEM CPU_DATMDI_RJ45_TP
10u 0.01u 0.01u *R3431 012
CPU_A3.3V CPU_OS_CLK2 220 011
CKZ CZB CZB TU_DEMOD_SCL CPU_DATMDI_RJ45_TN
CPU_DATMDI_RJ45_TN
*C3347 C3348 CPU_OS_DAT2 *R3430 220 011 012
010 TU_DEMOD_SDA
D+3.3V 10u 0.1u TP3323 CPU_DATMDI_RJ45_RP
FB3302 CPU_DATMDI_RJ45_RP
C3303 C3306 C3307
A192WJ
CZB DVB_SPI_CLK1 012
CPU_AVDD3.3V 16V
0.01u 0.01u 0.01u 10V CPU_DATMDI_RJ45_RN
KZA837WJQZ CPU_DATMDI_RJ45_RN
CZB CZB CZB 012
010
M+1.8V
LAN_LED0 TP3355
C3324 C3328 C3329 LAN_LED1 TP3356
010 0.1u 0.1u 0.1u C3338 C3341 C3343 C3345
D+1.1V
1u C3340 0.01u C3342 0.01u C3344 0.01u C3346
16V 16V 16V
TO MAIN5(DDR) C3320
0.01u 0.01u 0.01u 0.01u
005 C3318 4.7u
D+1.5V 2 1 2 1 2 1 C3337 LDM_CLK TP3340
4.7u 10V C3331 C3333 C3335
C3304 10V 0.1u C3332 C3334 C3336 4.7u
KZA761WJQZ 0.1u 0.1u LDM_CS
4.7u 0.1u 0.1u 0.1u 10V TP3341
KZA761WJQZ 4 3 4 3 4 3 KZA761WJQZ
10V
TO MAIN11(DTV_CI) KZA761WJQZ C3305 C3309 C3312 C3315 LDM_DI TP3342
1u C3308 0.01u C3310 0.01u C3313 0.01u C3316 6 5 6 5 6 5
011 0.01u 0.01u 0.01u 0.01u
CPU_A+1.2V MT5135_INT 011 LDM_DO
MT5135_INT TP3343
C3396
8 7 8 7 8 7
0.1u LDM_VSYNC TP3344
TL3301
I
DEMOD_TSCLK
*C3302
TO MAIN6(FLASH)
5 4 10u 10V DEMOD_TSVAL SD_CLK 006
KZA616WJQZ SD_CLK
VOUT VIN DEMOD_TSSYNC SD_CMD 006
SD_CMD
IC3301 DEMOD_TSDATA0
SD_D0 006
SD_D0
S172B12U SD_D1 006
SD_D1
ON GND NC TO MAIN5(DDR) C3321 B_DDR_A3 B_DDR_A9 B_DDR_BA1 B_DDR_MCLK0P_621MHz B_DDR_DQS1N LVDS0_D1P LVDS0_CLKP_74MHz LVDS0_D4P *R3432 *R3365 SD_D2 006
0.01u B_DDR_A2 B_DDR_A12 B_DDR_CLKEN B_DDR_DQS0N B_DDR_DQ11 LVDS0_D0P LVDS0_D2P LVDS0_D3P VBO_TXA+ VBO_TXB+ VBO_TXC+ VBO_TXD+ SD_D2
0 SB1FF SB1FF 0
1 2 3 NC NC NC NC NC NC NC NC
011 SD_D3 006
R3307 SD_D3
A1 A2 A3 A4 A6 A7 A8 A10 A11 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 ATSC_TS_CLK
1
2
7
TO MAIN5(DDR) 330 F
C3301 005 011
0.1u 10V B_DDR_RESET ATSC_TS_VAL
3
4
B_DDR_BA0 B_DDR_A7 B_DDR_A4 B_DDR_MCLK0N_621MHz B_DDR_DQS1P LVDS0_D1N LVDS0_CLKN_74MHz LVDS0_D4N
5
005 005 B_DDR_A5 B_DDR_A11 B_DDR_A10 B_DDR_DQS0P B_DDR_DQ9 LVDS0_D0N LVDS0_D2N LVDS0_D3N VBO_TXA- VBO_TXB- VBO_TXC- VBO_TXD-
B_DDR_CS0# RVREF6 011
A_DDR_RESET NC NC NC NC NC NC NC NC ATSC_TS_SYNC
TO MAIN8(PANEL)
5
6
3
005
005 B1 B2 B3 B4 B6 B7 B8 B10 B11 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32
B_DDR_RAS# A_DDR_CS0# R3308 011
008 ATSC_TS_D0
7
8
LVDS0_D0N 005
1
005 330 F
B_DDR_CAS#
008 A_DDR_RAS#
LVDS0_D0P 005 B_DDR_ODT B_DDR_A6 B_DDR_A1 B_DDR_DQ8 B_DDR_DQ12 B_DDR_DQM1
B_DDR_WE# 005 B_DDR_CS0# B_DDR_A13 B_DDR_BA2 B_DDR_DQ14 B_DDR_DQM0 B_DDR_DQ13 LVDS1_D0N LVDS1_D2N LVDS1_D3N VBO_HTPDN
008 A_DDR_CAS#
C3319 NC NC NC TO MAIN1(TUNER)
LVDS0_D1N 005
B_DDR_ODT 005 0.01u
008 A_DDR_WE# C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C17 C19 C21 C23 C25 C27 C29 C30 C31 C32
LVDS0_D1P 005 CPU_U2RX SD_DET
005 PNL_POW SD_WP
008 B_DDR_CLKEN A_DDR_ODT
H LVDS0_D2N
LVDS0_D2P
008
B_DDR_BA0
005
005
A_DDR_CLKEN
005 R3312 56 B_DDR_A8
B_DDR_A0
B_DDR_WE#
B_DDR_DQ10
B_DDR_DQ7
B_DDR_DQ3
B_DDR_DQ1 B_DDR_DQ15 LVDS1_D0P LVDS1_D2P LVDS1_D3P VBO_LOCKN
NC NC NC
RVREF6
005
B_DDR_BA1 A_DDR_BA0
008 D1 D2 C3325 D3 D4 D5 D6 D7 D8 D9 D10 D11 D13 D14 D15 D17 D19 D21 D23 D25 D27 D29 D30 D31 D32
LVDS0_CLKN_74MHz 005 0.01u
B_DDR_BA2 005 RVREF6 CPU_U2TX STB_CPU LDM_DO
008 A_DDR_BA1 CVBS_OUT_MUTE
LVDS0_CLKP_74MHz
005 B_DDR_RESET B_DDR_RAS# B_DDR_DQ6 LVDS1_D1P LVDS1_CLKP_74MHz LVDS1_D4P
008 005 A_DDR_BA2 B_DDR_CAS# B_DDR_DQ5 B_DDR_DQ0 B_DDR_DQ4 LVDS1_D1N LVDS1_CLKN_74MHz LVDS1_D4N
LVDS0_D3N B_DDR_A0 NC NC NC NC NC NC
008 005
LVDS0_D3P B_DDR_A1 E3 E4 E5 E6 E7 E8 E9 E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20 E22 E23 E24 E25 E26 E27 E28 E29 E30 E31 E32 DEMOD_RST
005
008 005 A_DDR_A0 A_DDR_DQ22 N_TUN_SAT_RST LDM_CLK LDM_CS
LAMP_ERR_CPU
LVDS0_D4N B_DDR_A2 A_DDR_DQ20 R3352 *R3356 0
005 R3344 12K 011
008 005 A_DDR_A1 ATSC_DEMOD_RST
10K
F
R3424
LVDS0_D4P B_DDR_A3 B_DDR_DQ2
005 4.7K
008 005 A_DDR_A2
LVDS1_D0N B_DDR_A4
005 F1 F2 F3 F6 F7 F9 F10 F13 F14 F18 F19 F20 F21 F22 F23 F28 F29 F30 F31 F32
008 005 A_DDR_A3 A_DDR_DQM3 A_DDR_DQ18 LDM_DI LDM_VSYNC
LVDS1_D0P B_DDR_A5 A_DDR_DQ16 CVBS1_PLUG
005 CPU_IF_AGC 001
008 005 A_DDR_A4 CPU_IF_AGC
LVDS1_D1N B_DDR_A6
005
008 005 A_DDR_A5
LVDS1_D1P B_DDR_A7
005 G1 G2 G3 G4 G5 G7 G14 G24 G26 G30 G31 G32
008 005 A_DDR_A6
LVDS1_D2N B_DDR_A8 A_DDR_DQS2N A_DDR_DQM2 A_DDR_DQ27 CPU_LED UCOM_RST
CVBS2_PLUG
005 A_DDR_DQS2P A_DDR_DQ29 R3327 47 C3394
008 005 A_DDR_A7 CPU_ATV_IF+ R3440 001
LVDS1_D2P B_DDR_A9 CPU_ATV_IFP
0.01u 0
005 C3395
005 A_DDR_A8 CPU_ATV_IF- R3443 001
008 CPU_ATV_IFN
LVDS1_CLKN_74MHz B_DDR_A10 0.01u 0
005
008 005 A_DDR_A9 H1 H2 H3 H4 H5 H6 H8 H14
LVDS1_CLKP_74MHz B_DDR_A11 A_DDR_DQS3N A_DDR_DQ25
005
008 005 A_DDR_A10 A_DDR_DQS3P A_DDR_DQ31 R3329 47
LVDS1_D3N B_DDR_A12
G LVDS1_D3P
008
B_DDR_A13
005 A_DDR_A11
005
005
0
008 A_DDR_A12
LVDS1_D4N J1 J2 J6 J8 J14 J30 J31 J32
R3439
005 005 A_DDR_DQ19 COMP2_PLUG N_CPU_USB1_FLG
008 B_DDR_MCLK0P_621MHz A_DDR_A13 UCOM_MODE
A_DDR_DQ17
LVDS1_D4P
005
B_DDR_MCLK0N_621MHz
005
A_DDR_MCLK0P_621MHz
005 K1 K2 K4 K6 K28 K29 K30 K31 K32
B_DDR_DQM0 005
A_DDR_MCLK0N_621MHz A_DDR_DQ21 TCON_ROM_EN CPU_GPIO13CPU_USB1_EN S1_PLUG
005 CPU_GCK5
A_DDR_DQ23
B_DDR_DQM1
D3318
005 005
2
B_DDR_DQS0P A_DDR_MCLK1P_621MHz A192WJ 1SS226
3
005 005 FB3303
B_DDR_DQS0N A_DDR_MCLK1N_621MHz L1 L2 L3 L4 L5 L6 L7 L11 L12 L13 L14 L15 L16 L22 L23 L27 L28 L29 L30 L31 L32
1
005 A_DDR_MCLK1N_621MHz A_DDR_DQ24 A_DDR_DQ30 N_TUN_RST SD_D2 COMP1_PLUG
AMP_PROTECT SD_D3
B_DDR_DQS1P 005 A_DDR_MCLK1P_621MHz A_DDR_DQ26 A_DDR_DQ28
A_DDR_DQM0
2
005 D3319
B_DDR_DQS1N 005
A_DDR_DQM1 1SS226
3
005 M3 M4 M5 M11 M12 M13 M14 M15 M16 M17 M19 M20 M22 M23 M28 M30
1
005 A_DDR_DQM2
B_DDR_DQ0 A_DDR_ODT A_DDR_CLKEN TUN_GAIN_SW SD_D1
005
005 A_DDR_DQM3
A_DDR_CAS#
*IC3303 D3320
2
B_DDR_DQ1 1SS226 C3375 R3395
005
A_DDR_DQS0P IXD220WJQZ 0.01u 68
3
005
B_DDR_DQ2 PC_RP 002
005 PC_RED
1
005 A_DDR_DQS0N N1 N2 N3 N4 N5 N6 N11 N12 N13 N14 N15 N16 N17 N18 N19 N20 N21 N23 N27 N28 N29 N30 N31 N32 C3360 R3367
PC_GP 002
B_DDR_DQ3 005 A_DDR_A13 A_DDR_A0 A_DDR_A10 HP_PLUG SP_MUTE SD_CMD PC_GREEN
AC_DET_CPU SD_CLK SD_D0 0.01u 68
A_DDR_DQS1P A_DDR_A3 A_DDR_WE#
2
005 D3327 C3356
B_DDR_DQ4 PC_SOG R3372
005 QZ Not use SRS 1SS226
F
3
A_DDR_DQS1N 1500P 0
005 R3362
B_DDR_DQ5 PC_BP C3357 002
N1 Use SRS PC_BLUE
1
005 0.01u 68
005 A_DDR_DQS2P R3363
B_DDR_DQ6 P1 P2 P3 P4 P5 P6 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 P28 P29 P30 P31 P32 PC_VGACOM C3358 002
005 A_DDR_A9 A_DDR_A7 A_DDR_BA1 CI_SPI_CLE DVB_SPI_CLK1 CI_SPI_DATA PC_RGB_COM
A_DDR_DQS2N 0.01u 100
005 A_DDR_RESET A_DDR_A2 A_DDR_A12 MT5135_INT CI_SPI_CLK
B_DDR_DQ7 PC_HSYNC 002
005 D3322 PC_HSYNC
A_DDR_DQS3P
2
005 1SS226
B_DDR_DQ8 PC_VSYNC 002
005 PC_VSYNC
3
005 A_DDR_DQS3N
B_DDR_DQ9 R3 R4 R5 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R26 R27 R28 R29 R31 R32
1
005 A_DDR_A5 A_DDR_A11
B_DDR_DQ10 005 A_DDR_BA0
A_DDR_DQ0
2
005 D3328
B_DDR_DQ11 005 SC_Y0P C3361 R3381 002
1SS226
3
A_DDR_DQ1 BLUE1
005 0.01u
B_DDR_DQ12 68
1
005 T1 T2 T3 T4 T5 T6 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20 T21 T27 T28 T29
A_DDR_DQ2 SC_SOY0 R3382 002
005 A_DDR_CS0# A_DDR_BA2 A_DDR_A6 SC1FSW
B_DDR_DQ13 005 D3323
A_DDR_DQ3 A_DDR_RAS# A_DDR_A8 0
2
005 1SS226 C3363
B_DDR_DQ14 SC_PB0P R3373 002
005 GREEN1
3
A_DDR_DQ4 A_DDR_DQ6 A_DDR_A1 DEMOD_RST 0.01u
005 A_DDR_DQ4 A_DDR_A4 RVREF5 DEMOD_TSDATA0 DEMOD_TSCLK 68
1
B_DDR_DQ15 005
A_DDR_DQ5 U1 U2 U3 U4 U5 U7 U11 U12 U13 U14 U15 U16 U17 U18 U19 U20 U21 U22 U28 U29 U30 U31 U32 SC_PR0P C3364 R3374 002
RED1/C1
005 0.01u
2
A_DDR_DQ6 D3329 68
1SS226 C3365 R3375
3
005 SC_COM0 002
A_DDR_DQ7 C3330 CPU_AOSDATA0 SC_RGB_COM
A_DDR_DQ0 DEMOD_TSVAL CPU_OS_DAT2 0.01u
1
005 A_DDR_DQ2 0.01u CPU_ALIN CPU_AOSDATA1 DEMOD_TSSYNC CPU_OS_CLK2 100
A_DDR_DQ8
008 V1 V2 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 V22 V26 V27 V28 V29 V30 V31 V32
VBO_TXA- 005
TO MAIN6(FLASH) A_DDR_DQ9 D3304
COMP_Y1P C3366 R3383 002
2
008 1SS226 COMP1_Y
VBO_TXA+ 006 005 0.01u
FLASH_CE0# A_DDR_DQ10 68
3
E VBO_TXB-
008
005 A_DDR_DQM1 A_DDR_DQ13 DSUB_WP CPU_IF_AGC COMP_SOY1
C3367 R3384 002
COMP1_SOY
1
A_DDR_DQ11 1500P
008 006 W1 W3 W4 W5 W11 W12 W13 W14 W15 W16 W17 W18 W19 W20 W21 W22 W23 W29 W30 0
VBO_TXB+ NAND_CE1# 005 C3368
A_DDR_DQ12 COMP_PB1P R3376 002
2
006 D3324 COMP1_Pb
VBO_TXC- 008 0.01u
NAND_RB# 005 68
1SS226
3
A_DDR_DQ13
008 006 COMP_PR1P C3369 R3377
VBO_TXC+ NAND_ALE CPU_AOSDATA3 CPU_AOLRCK CPU_AOMCLK 002
1
005 A_DDR_DQS0P A_DDR_DQ11 COMP1_Pr
A_DDR_DQ14 A_DDR_DQS0N A_DDR_DQM0 A_DDR_DQ15 CPU_AOSDATA4 CPU_AOSDATA2 CPU_AOBCK 0.01u
008 006 68
VBO_TXD- NAND_CLE 005 Y1 Y2 Y3 Y4 Y6 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y20 Y21 Y22 Y27 Y28 Y29 Y30 Y31 Y32 D3307
A_DDR_DQ15 C3370 R3378
2
008 006 1SS226 COMP_COM1 002
COMP1_COM
VBO_TXD+ NAND_WE# 005 0.01u
3
A_DDR_DQ16 100
006
NAND_OE#
1
008 005 A_DDR_DQ14 C3371
VBO_LOCKN A_DDR_DQ17 CPU_OPWM2 CPU_OS_DAT0 CPU_ASPDIF ANALOG_CPU_SY0 R3370 R3412 002
A_DDR_DQ12 A_DDR_DQ9 CPU_OPWM0 LAN_LED1 CPU_OS_CLK0 0.047u
ANALOG_SY0
008 006 005 AA3 AA4 AA5 AA11 AA12 AA13 AA14 AA15 AA16 AA17 AA18 AA19 AA20 AA21 AA22 AA26 AA27 AA28 AA29 AA30 AA31 AA32 10V 100 0
2
VBO_HTPDN NAND_D0 A_DDR_DQ18 D3325
C3372 R3413
1SS226
3
006 005 ANALOG_CPU_SC0 0.047u R3371 002
NAND_D1 A_DDR_DQ19 ANALOG_SC0
10V 100 0
1
006 005 R3347 R3349
NAND_D2 A_DDR_DQ20 A_DDR_DQS1P A_DDR_DQ10
A_DDR_DQS1N A_DDR_DQ1 A_DDR_DQ8 LAN_LED0 CPU_SY1 TP3321
006 005 F 12K F
12K
NAND_D3 A_DDR_DQ21 AB1 AB2 AB3 AB4 AB5 AB6 AB11 AB12 AB13 AB14 AB15 AB16 AB17 AB18 AB19 AB20 AB21 AB22 AB28 AB29 AB30 D3321 CPU_SC1 TP3322
2
006 005 CPU_OS_DAT1 1SS226
NAND_D4 A_DDR_DQ22 CPU_OS_CLK1 C3373 R3414
3
CPU_CVBS0P R3379 001
006 005 D3305 TUNER_CVBS
NAND_D5 A_DDR_DQ23 0.047u 100 0
1
A_DDR_DQ7 EXA697WJQZ
006 005 A_DDR_DQ3 A_DDR_DQ5 CPU_U1TX CPU_U1RX CPU_OPWM1 R3415
CPU_CVBS1P 5.6V C3374 R3380 002
NAND_D6 A_DDR_DQ24
AC1 AC2 AC3 AC4 AC12 AC13 AC15 AC17 AC19 AC20 AC21 AC27 AC28 AC29 AC30 AC31 AC32 CVBS1_IN
2
D3326 D3306 0.047u 100 0
006 005
NAND_D7 A_DDR_DQ25 1SS226
3
EXA697WJQZ
CPU_CVBS2P C3388 R3311 R3330 002
005 5.6V SC/Y_CVBS2_IN
1
A_DDR_DQ26 D3330 0.047u 100 0
D TO MAIN12(LAN_USB)
A_DDR_DQ27
005
005
AD3 AD4 AD5 AD26
CPU_GPIO7
AD27
CPU_GPIO8
AD28 AD30
CPU_DATMDI_RJ45_TN CPU_DATMDI_RJ45_TP
AD31 AD32
EXA697WJQZ
5.6V
A_DDR_DQ28
CPU_CVBSCOM 002
012 005 CVBS_COM
USB_D0P A_DDR_DQ29 C3359
012 005 A_DDR_MCLK0P_621MHz 1u
USB_D0N A_DDR_DQ30 A_DDR_MCLK0N_621MHz CPU_DATMDI_RJ45_RN CPU_DATMDI_RJ45_RP CPU_BYPASS0 TP3324
012 005 AE1 AE2 AE4 AE9 AE10 AE14 AE25 AE26 AE27 AE30 AE31 AE32
USB_D1P A_DDR_DQ31 CPU_BYPASS1 TP3325
OPCTRL0 C3355
012
USB_D1N 0.01u
CPU_VDAC2_OUT TP3327
NC NC
*C3392 0.1u
TO MAIN3(HDMI) AF1 AF2 AF3 AF8 AF9 AF10 AF12 AF13 AF14 AF16 AF17 AF18 AF19 AF20 AF22 AF23 AF25 AF26 AF27 AF28 AF29 AF30 AF31 AF32 CPU_SIF 001
SIF
CPU_SIF_COM C3393
003 OPCTRL6 OPWRSB CPU_VGA_SCL KEY1_CPU KEY2_CPU QSTEMP_CPU CPU_SIF
SW_TMDS_D0P R3354 0 0.1u
003
SW_TMDS_D0N CPU_ADACL2 TUNER_OUT_L
PM_REQ CPU_ADACR2 TUNER_OUT_R
003
330
SW_TMDS_D1P AG1 AG2 AG3 AG4 AG5 AG8 AG10 AG12 AG13 AG14 AG16 AG17 AG19 AG20 AG23 AG26 AG27 AG28 AG29 AG30 AG31 AG32
003 R3434
SW_TMDS_D1N OPCTRL1 CPU_RC CPU_VGA_SDA SLOWSW2 SLOWSW1 CPU_SIF_COM COMP1_AINL1 R3387 *C3378 002
R3353
COMP1_IN_L
003 D3310 30K 10u 16V
SW_TMDS_D2P EXA713WJQZ
1K
EJTAG_TCK EJTAG_TDI COMP1_AINR1 R3388 *C3379 002
EJTAG_TDO EJTAG_TMS CPU_ADACL3 12V COMP1_IN_R
003
1K
D3311 30K 10u 16V
0
SW_TMDS_D2N
R3350
0
AH1 AH2 AH3 AH4 AH6 AH7 AH8 AH10 AH12 AH13 AH14 AH16 AH17 AH20 AH23 AH24 AH26 AH27 AH28 AH29 AH30 EXA713WJQZ
C3387 CVBS1_AINL2 R3389 *C3380 002
R3435
003 F 12V CVBS1_IN_L
R3417
SW_TMDS_CLKP_222.75MHz I2C_READY ANT+5V_SW_CPU HP_MUTE CPU_U0TX OPC_CPU R3418 0 0.01u D3312 30K 10u 16V
R3333 5.1K R3339 C3351 C3353 EXA713WJQZ
003 0 1u CVBS1_AINR2 12V R3390 *C3381 002
SW_TMDS_CLKN_222.75MHz 2.2u C3354 CVBS1_IN_R
C3349 D3313 30K 10u 16V
ORESET# 1u 1u HP_MON_L EXA713WJQZ
C TO MAIN12(LAN_USB)
TP3301 HDMI_CEC_CPU EJTAG_TRST#
AJ3
NAND_WE#
AJ4
NAND_D5
AJ5 AJ6 AJ8
SMPOWHOLD
AJ9
HDMI_CEC_CPU
AJ10 AJ11 AJ12 AJ13
C3339
4.7u
AJ17 AJ18
C3386
0.01u AJ20
CPU_BYPASS1
AJ21 AJ22
CPU_CVBS1P
AJ23 AJ24 AJ25 AJ26 AJ27 AJ28 AJ29
CPU_ADACR3
AJ30 AJ31
HP_MON_R
AJ32
CVBS2_AINL3 12V
D3314
EXA713WJQZ
R3391
30K
*C3382
10u 16V
002
CVBS_IN2_L
012 N_USB_RST N_FRC_RST DET_PNL_12V_CPU POW_SW_CPU OPCTRL5 CPU_U0RX 10V CVBS2_AINR3 12V R3392 *C3383 002
N_USB_RST COMP_COM1 COMP_PR1P CPU_VDAC1_OUT CPU_BYPASS0 CVBS_IN2_R
KZA761WJQZ PC_HDMI_AINR4 D3315 30K 10u 16V
EXA713WJQZ
TO MAIN6(FLASH) PC_HDMI_AINL4 12V R3393 *C3384 002
NAND_CLE PC_HDMI_L
006 NAND_ALE NAND_OE# NAND_D4 NAND_D6 N_USB_RST N_KEY_RST_CPU ANALOG_CPU_SC0 CPU_CVBSCOM COMP1_AINL1 CVBS2_AINR3 COMP1_AINR1 D3316 30K 10u 16V
SMPOWHOLD EXA713WJQZ
AK1 AK2 AK3 AK4 AK5 AK6 AK7 AK8 AK9 AK10 AK11 AK12 AK13 AK14 AK15 AK16 AK17 AK18 AK19 AK20 AK21 AK22 AK23 AK24 AK25 AK26 AK27 AK28 AK29 AK30 AK31 AK32 PC_HDMI_AINR4 12V R3394 *C3385 002
PC_HDMI_R
D3317 30K 10u 16V
TO MAIN7(UCOM) PNL_WP PNL_EN PNL_I2C_EN OPCTRL4 PC_BP PC_SOG PC_GP COMP_PB1P SC_PR0P CPU_VDAC2_OUT CPU_CVBS2P EXA713WJQZ
007 SMPOWHOLD CPU_CVBS0P 12V
SMPOWHOLD
NAND_D0 SW_TMDS_CLKP_222.75MHz CVBS1_AINL2 CVBS1_AINR2
FLASH_CE0# NAND_D2 NAND_D7 USB_D1P USB_D0P SW_TMDS_D0P SW_TMDS_D2P CVBS2_AINL3 ATV_AINL5 ATV_AINR5
F
007 PM_REQ AL1 AL2 AL3 AL5 AL6 AL7 AL9 AL10 AL11 AL12 AL13 AL15 AL16 AL18 AL19 AL21 AL22 AL24 AL26 AL27 AL29 AL30 AL31 AL32
PM_REQ CPU_AINL6 TP3319
SW_TMDS_D1P PC_HSYNC PC_VGACOM COMP_SOY1 SC_SOY0 SC_COM0 CPU_SC1 CPU_ATV_IF-
TP3302
560
N_KEY_RST_CPU CPU_AINR6 TP3320
R3343
NAND_D1 SW_TMDS_CLKN_222.75MHz SC1_AINL0 SC1_AINR0
NAND_RB# NAND_D3 NAND_CE1# USB_D1N USB_D0N SW_TMDS_D0N SW_TMDS_D2N PC_HDMI_AINL4 CPU_AINL6 CPU_AINR6
AM1 AM2 AM3 AM5 AM6 AM7 AM9 AM10 AM11 AM12 AM13 AM15 AM16 AM18 AM19 AM21 AM22 AM24 AM26 AM27 AM29 AM30 AM31 AM32 CPU_AOLRCK R3359 009
SP_LRCLK
47 FB3304
SW_TMDS_D1N PC_VSYNC PC_RP COMP_Y1P SC_Y0P SC_PB0P ANALOG_CPU_SY0 CPU_SY1 CPU_ATV_IF+ 1043CE
CPU_AOBCK R3360 009
SP_BCLK
220
CPU_AOSDATA0 R3361 009
SP_DATA
47
CPU_AOSDATA1 TP3330
CPU_AOSDATA2 TP3331
CPU_AOSDATA3 TP3332
B CPU_AOSDATA4 TP3333
TO_MAIN9(AUDIO_AMP)
NC
1 3 5 7 HP_MON_L R3401 C3362 009
R3305 HP_MONITOR_L
22K 1u 10V
SD_WP
R3346
2.2K
OPWRSB
1K
SLOWSW1
SLOWSW2
PNL_WP
SD_DET
DSUB_WP
PNL_EN
PNL_POW
OPC_CPU
HP_MUTE
SP_MUTE
ORESET#
HP_PLUG
OPCTRL4
OPCTRL5
OPCTRL0
OPCTRL1
UCOM_RST
UCOM_MODE
STB_CPU
CPU_LED
OPCTRL6
S1_PLUG
CPU_OPWM1
CPU_OPWM2
CPU_OPWM0
CPU_GCK5
CPU_U1RX
CPU_U0RX
CPU_U2RX
1M
CPU_U1TX
POW_SW_CPU
KEY1_CPU
KEY2_CPU
CPU_U0TX
CPU_U2TX
SB1FF HP_MON_R R3406 C3389 009
N_FRC_RST
N_TUN_RST
QSTEMP_CPU
COMP1_PLUG
COMP2_PLUG
CPU_GPIO7
CPU_GPIO8
TCON_ROM_EN
AC_DET_CPU
CVBS1_PLUG
CVBS2_PLUG
I2C_READY
AMP_PROTECT
CPU_VGA_SDA
CPU_GPIO13
CPU_VGA_SCL
HP_MONITOR_R
CPU_OS_DAT0
CPU_OS_DAT1
TUN_GAIN_SW
CPU_USB1_EN
CPU_OS_CLK0
CPU_OS_CLK1
LAMP_ERR_CPU
PNL_I2C_EN
CVBS_OUT_MUTE
ANT+5V_SW_CPU
22K 1u 10V
N_TUN_SAT_RST
4.7K
4.7K
R3351
N_CPU_USB1_FLG
DET_PNL_12V_CPU
2 4 6 8
R3345
X3301 D3303
R3320
R3323
10
NC
SCA237WJQZ PXA018WJ
47
10
EJTAG_TRST#
R3335
10
47
47
10
10K
4 NC 3
10
10
47
4.7K
4.7K
R3338
R3306 EJTAG_TDI
10
10
10
CPU_ADACL2 TP3334
R3433
R3340
10K
10
*R3310
R3321
R3324
R3337
R3436
*R3309
10K
TP3307
TP3311
TP3312
TP3357
TP3315
TP3316
10
R3325
R3313
R3314
CPU_ADACR2
10K
10K
TP3335
R3409
R3410
EJTAG_TDO
47
1 NC 2
10K
10K
R3348
C3350 C3352 CPU_ADACL3 TP3336
R3421
R3316
R3318
R3341
7P 27MHz
R3419
EJTAG_TMS
R3411
R3420
7P CPU_ADACR3 TP3337
50V
50V
006
006
006
006
006
006
006
006
006
006
002
002
002
002
002
002
002
002
009
009
009
009
008
008
008
008
008
008
008
010
010
010
010
010
001
001
001
007
007
007
012
012
CPU_ASPDIF R3368 002
006
OPT_OUT
CPU_ALIN 47
TP3338
TP3308
TP3354
TO_MAIN3(HDMI)
TP3328
TP3326
CONFIG PIN
TP3314
TP3329
TP3345
TP3346
TP3347
TP3348
TP3350
TP3351
TP3352
TP3353
R3369 003
TO MAIN6(FLASH)
HDMI_OPT_OUT
47
TO MAIN9(AUDIO AMP)
TO MAIN12(LAN_USB)
TO MAIN2(TERMINAL)
TO_MAIN6(FLASH)
TO MAIN10(POWER)
TO MAIN1(TUNER)
TO MAIN7(UCOM)
R3398 006
TO MAIN8(PANEL)
CPU_UARXD1_UCOM
CPU_UATXD1_UCOM
CPU_A_SPDIF
TO MAIN6(FLASH)
N_CPU_USB1_FLG
47
CVBS_OUT_MUTE
CPU_UATXD0_RS
N_TUN_SAT_RST
CPU_UARXD0_RS
TCON_ROM_EN
AMP_PROTECT
TUN_GAIN_SW
CPU_USB1_EN
COMP1_PLUG
UCOM_MODE
CVBS1_PLUG
CVBS2_PLUG
PANEL_OFL1
PNL_I2C_EN
PNL_I2C_EN
N_CPU_RST
N_PER_RST
You might also like
- Parasite SEO Secrets Revealed by Charles Floate100% (1)Parasite SEO Secrets Revealed by Charles Floate73 pages
- Introduction-to-TikTok-Shop-Affiliate-Program 2No ratings yetIntroduction-to-TikTok-Shop-Affiliate-Program 210 pages
- Gauranga Das - The Art of Focus (2021, Penguin Random House India Private Limited) - Libgen - Li67% (3)Gauranga Das - The Art of Focus (2021, Penguin Random House India Private Limited) - Libgen - Li253 pages
- Cambridge International Exam Fees Lists May June 2024No ratings yetCambridge International Exam Fees Lists May June 20244 pages
- Exploring The Preferences For Micro-Apartments: Nezar Mabrouk H. Soub İpek MemikoğluNo ratings yetExploring The Preferences For Micro-Apartments: Nezar Mabrouk H. Soub İpek Memikoğlu12 pages
- Building Code Requirements For Structural Concrete Reinforced With Glass FiberReinforced Polymer (GFRP) Bars Code and Commentary 440.11.22 Chapter 22100% (1)Building Code Requirements For Structural Concrete Reinforced With Glass FiberReinforced Polymer (GFRP) Bars Code and Commentary 440.11.22 Chapter 2232 pages
- The Use of Artificial Intelligence As Educational Tool To Help Students To Improve Writing SkillsNo ratings yetThe Use of Artificial Intelligence As Educational Tool To Help Students To Improve Writing Skills2 pages
- Sharp AQUOS LC - (32/40/46/52) LE700UN Service Manual78% (32)Sharp AQUOS LC - (32/40/46/52) LE700UN Service Manual156 pages
- Communication Aids and Strategies Using Tools of TechnologyNo ratings yetCommunication Aids and Strategies Using Tools of Technology32 pages
- How To Test Diodes With A Digital Multimeter - FlukeNo ratings yetHow To Test Diodes With A Digital Multimeter - Fluke6 pages
- Assembly Manual: In-Circuit LOPT/FBT Tester K 7205100% (1)Assembly Manual: In-Circuit LOPT/FBT Tester K 72056 pages
- Paghahandog (Lyrics and Chords) - Catholic Songbook™ - Catholic Songs - Catholic Liturgical Hymns - Music With Lyrics and ChordsNo ratings yetPaghahandog (Lyrics and Chords) - Catholic Songbook™ - Catholic Songs - Catholic Liturgical Hymns - Music With Lyrics and Chords5 pages
- Service Manual LC-40LE830M LC-46LE830M LC-52LE830M LC-60LE830M67% (3)Service Manual LC-40LE830M LC-46LE830M LC-52LE830M LC-60LE830M132 pages
- Udgam School For Children: Page 1 of 2 Class-VII / Subject - English / WorksheetNo ratings yetUdgam School For Children: Page 1 of 2 Class-VII / Subject - English / Worksheet2 pages
- Sharp LC-60LE635, 60LE635, 60LE636, 60LE638ENo ratings yetSharp LC-60LE635, 60LE635, 60LE636, 60LE638E65 pages
- Project Management: - Dr. Gyanesh Kumar Sinha Associate Professor - Operations and AnalyticsNo ratings yetProject Management: - Dr. Gyanesh Kumar Sinha Associate Professor - Operations and Analytics10 pages
- Practical Guides to Testing and Commissioning of Mechanical, Electrical and Plumbing (Mep) InstallationsFrom EverandPractical Guides to Testing and Commissioning of Mechanical, Electrical and Plumbing (Mep) Installations4/5 (4)
- Sharp LC-40LE830E LC-46LE830E LC-40LE831E LC-46LE831E (SM) - 69124No ratings yetSharp LC-40LE830E LC-46LE830E LC-40LE831E LC-46LE831E (SM) - 6912492 pages
- Service Manual: LC-60LE635E (B) /RU (B) LC-60LE636E (B) /S (B) LC-60LE638E (B)No ratings yetService Manual: LC-60LE635E (B) /RU (B) LC-60LE636E (B) /S (B) LC-60LE638E (B)65 pages
- Computer Network - CS610 Power Point Slides Lecture 12No ratings yetComputer Network - CS610 Power Point Slides Lecture 1220 pages
- The Unofficial WG K7000 Repair Guide: Arcade Monitor Troubleshooting Guides, #1From EverandThe Unofficial WG K7000 Repair Guide: Arcade Monitor Troubleshooting Guides, #1No ratings yet
- Sharp Lc-60-70le650u 70le657u 70757u C6500u Le755u Le857u C7500u100% (1)Sharp Lc-60-70le650u 70le657u 70757u C6500u Le755u Le857u C7500u136 pages
- Coastal Engineering Manual: Overview And Coastal HydrodynamicsFrom EverandCoastal Engineering Manual: Overview And Coastal HydrodynamicsNo ratings yet
- LCD Sharp LC-60LE745U - LC-60C7450 - LC60C8470 - LC-60LE845 - LC-70LE745U - LC-70LE7450 - LC-70LE845 - LC-70LE845 - LC-708470 - LC-70LE847No ratings yetLCD Sharp LC-60LE745U - LC-60C7450 - LC60C8470 - LC-60LE845 - LC-70LE745U - LC-70LE7450 - LC-70LE845 - LC-70LE845 - LC-708470 - LC-70LE847100 pages
- AOC Le42h057d Le46h057d LCD TV Service Manual33% (3)AOC Le42h057d Le46h057d LCD TV Service Manual188 pages
- Sharp Lc-60-70le745u C7450u Le845u C8470u Le847u PDFNo ratings yetSharp Lc-60-70le745u C7450u Le845u C8470u Le847u PDF86 pages
- 7124742-Sharp Lc-40le830u 46le830u 52le830u 60le830u Service Manual Repair Guide100% (6)7124742-Sharp Lc-40le830u 46le830u 52le830u 60le830u Service Manual Repair Guide110 pages
- It Is Quite Another Electricity: Transmitting by One Wire and Without GroundingFrom EverandIt Is Quite Another Electricity: Transmitting by One Wire and Without GroundingNo ratings yet
- Service Manual: LC-42D64U LC-46D64U LC-52D64UNo ratings yetService Manual: LC-42D64U LC-46D64U LC-52D64U172 pages
- Service Manual: LC-42D64U LC-46D64U LC-52D64UNo ratings yetService Manual: LC-42D64U LC-46D64U LC-52D64U172 pages
- Manual de Serviço TV SHARP LC 42D64U LC 46D64U e LC 52D64U PDFNo ratings yetManual de Serviço TV SHARP LC 42D64U LC 46D64U e LC 52D64U PDF172 pages
- Service Manual: LC-32D41U LC-32M41U LC-40C32UNo ratings yetService Manual: LC-32D41U LC-32M41U LC-40C32U148 pages
- Sharp Lc-60-70le745u C7450u Le845u C8470u Le847uNo ratings yetSharp Lc-60-70le745u C7450u Le845u C8470u Le847u86 pages
- Sharp Lc-40le820 Lc-46le820 Lc-52le820 Lc-60le820No ratings yetSharp Lc-40le820 Lc-46le820 Lc-52le820 Lc-60le820106 pages
- Sharp Lc40le800un Lc46le810un Lc52810un Lc60le810un Led TV SM Final100% (2)Sharp Lc40le800un Lc46le810un Lc52810un Lc60le810un Led TV SM Final96 pages
- Reference Guide To Useful Electronic Circuits And Circuit Design Techniques - Part 1From EverandReference Guide To Useful Electronic Circuits And Circuit Design Techniques - Part 12.5/5 (3)
- Chainsaw Operator's Manual: Chainsaw Safety, Maintenance and Cross-cutting TechniquesFrom EverandChainsaw Operator's Manual: Chainsaw Safety, Maintenance and Cross-cutting Techniques5/5 (1)
- Reference Guide To Useful Electronic Circuits And Circuit Design Techniques - Part 2From EverandReference Guide To Useful Electronic Circuits And Circuit Design Techniques - Part 2No ratings yet
