SPECIFICATIONS – PTO DRIVEN: MODEL CP-4

CP-4 Pump Performance

FLOW PRESSURE
Model GPM l/min l/sec PSI bar kPa MPa
CP-4 60 200 3 1000 69 6900 6.9
CPT4-UHP 90 350 6 1350 93 9300 9.3

Pump Features Optional Equipment

Casings: • Priming System, see F-2418

• Pressure Control Systems:
Two-piece, horizontally-split, high-tensile, close-grained, gray iron
o Discharge Relief Valves, see F-897
(bronze optional).
o Intake Relief Valves, see F-2192
Wear Rings: • Corrosion Protection – Zinc Intake Screens and Anodes
Ni-resist; special “stepped” design to reduce internal leakage and • Overheat Protection Manager, see F-2422
increase efficiency. Replaceable by undersize rings to prolong pump • Drain Valves, see F-1158
life and minimize maintenance costs. • Discharge Valves, see F-1161
Impellers: • Tachometer drive available, operates at ½ input shaft speed.
Bronze, hydraulically and mechanically balanced - one integrally cast • Transmissions Available:
pair for the first and second stages and another for the third and
fourth stages. Impeller hubs are “stepped” to minimize internal K Series (PTO)
bypass. The K Series Transmission is normally used when a truck transmission
Stuffing Boxes: mounted power take-off is selected as the pump drive.
Adjustable braided flexible graphite (BFG) packing. Housings: Aluminum
Rotation: Drive Ratios: 1.62, 1.97, 2.14, 2.55, 2.79, 3.40, 4.00, 4.79
Available with either clockwise or counter-clockwise rotation of Gears: Helical, precision cut, crown shaved for proper load distribution
input shaft. and quiet operation.
Bearings:
All bearings are oil or grease lubricated, anti-friction (ball type), T Series (Direct Engine Mounted)
located outside the pump casing to accurately align and support the The T Series Transmission is supplied when the pump is to be mounted
impeller shaft assembly. Ball bearings are deep-groove type directly to the engine bell housing. This provides a clean, compact
designed to carry both radial and axial thrust. arrangement and allows for complete pump and roll capability.
Intake:
2” (5 cm) NPT T Transmissions are available in SAE 2, 3, 4, or 5 bell housing adapters.
Discharge: Housings: Aluminum
1-1/2” (3.8 cm) NPT Drive Ratios: 1.62, 1.97, 2.14, 2.55, 2.79, 3.40, 4.00, 4.79
Applications Gears: Helical, precision cut, crown shaved for proper load distribution
The CP-4 can be used either as an auxiliary pump to provide and quiet operation.
“booster” service on an apparatus that also has a rated midship
pump, or as the only pump on a mini-pumper, brush truck or other Industry Leading Sales and Support
special purpose vehicle. Especially adaptable to “pump and roll” When you purchase equipment, not only do you get quality
operation, the CP-4 pump will supply two or more high-pressure products, you get quality service. Our expert service technicians
booster reels with ultra-high pressure. Ideal for situations where a are the best in the business and they are always happy to answer
limited water supply is available and a high-pressure fog is desirable any service questions you might have.
for knocking out a fire quickly before it spreads.
Sales/Applications Assistance Service Assistance
Warranty
Phone: 651-450-5234 (Press 3) Phone: 651-450-5200
Waterous Seven-Year Limited Warranty (CP-4 Series Only, Contact [email protected] Fax: 800-488-1228
Waterous for Warranty details on the CPT-4UHP Series) [email protected]

Conditions of Sales
For details on Waterous Conditions of Sales, refer to F-2190,
Conditions of Sales located on the Waterous web site at
www.waterousco.com or by contacting Waterous.

 2020 Waterous Company 125 Hardman Avenue South, South St. Paul, Minnesota 55075-2456 USA F-1086
www.waterousco.com Specifications subject to change without notice. Revised: 04/20