Draft: March 2010

3%26)#% -!.5!,

For Orignal DAB Module up to S/N A86C71512400

#  # $!"
#$ 2ECEIVER

#  # $!"

#$ 2ECEIVER
PRODUCT SAFETY SERVICING GUIDELINES
CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN VOLTAGE MEASURE MUST NOT EXCEED 75 VOLTS R.M.S.
ANY WAY. NEVER PERFORM CUSTOMIZED INSTALLATIONS THIS CORRESPONDS TO 0.5 MILLIAMP AC ANY VALUE
WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL
MODIFICATIONS WILL NOT ONLY VOID THE WARRANTY, BUT SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY.
MAY LEAD TO YOUR BEING LIABLE FOR ANY RESULTING
PROPERTY DAMAGE OR USER INJURY.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU
ARE THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING
SAFETY CHECKS AND SERVICING GUIDELINES. TO DO
OTHERWISE, INCREASES THE RISK OF POTENTIAL HAZARDS
AND INJURY TO THE USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR
PROTECTION FROM AC LINE SHOCK.
SAFETY CHECKS SUBJECT : GRAPHIC SYMBOLS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN
CORRECTED. A CHECK SHOULD BE MADE OF THE EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE
FOLLOWING. PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE
PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
SUBJECT : FIRE & SHOCK HAZARD CONSTITUTE A RISK OF ELECTRIC SHOCK.
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
SUCH A WAY AS TO AVOID POSSIBILITY OF ADJACENT INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
COMPONENT SHORTS. THIS IS ESPECIALLY IMPORTANT LITERATURE ACCOMPANYING THE APPLIANCE.
ON THOSE MODULES WHICH ARE TRANSPORTED TO AND
FROM THE REPAIR SHOP.
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE SUBJECT : TIPS ON PROPER INSTALLATION
DEVICES SUCH AS INSULATORS, BARRIERS, COVERS, 1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS,
SHIELDS, STRAIN RELIEFS, POWER SUPPLY CORDS, AND CUBBYHOLE OR CLOSELY FITTING SHELF SPACE. OVER
OTHER HARDWARE HAVE BEEN REINSTALLED PER OR CLOSE TO HEAT DUCT, OR IN THE PATH OF HEATED
ORIGINAL DESIGN. BE SURE THAT THE SAFETY PURPOSE AIR FLOW.
OF THE POLARIZED LINE PLUG HAS NOT BEEN DEFEATED. 2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS:
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE OUTDOOR PATIO INSTALLATIONS WHERE DEW IS A
COLD SOLDER JOINTS, SOLDER SPLASHES OR SHARP FACTOR, NEAR STEAM RADIATORS WHERE STEAM
SOLDER POINTS. BE CERTAIN TO REMOVE ALL LOOSE LEAKAGE IS A FACTOR, ETC.
FOREIGN PARTICLES. 3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT
4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR REAR VENTING. THE CUSTOMER SHOULD ALSO AVOID THE
DETERIORATION TO PARTS AND COMPONENTS. FOR USE OF DECORATIVE SCARVES OR OTHER COVERINGS
FRAYED LEADS, DAMAGED INSULATION (INCLUDING AC WHICH MIGHT OBSTRUCT VENTILATION.
CORD). AND REPLACE IF NECESSARY FOLLOW ORIGINAL 4. WALL AND SHELF MOUNTED INSTALLATIONS USING A
LAYOUT, LEAD LENGTH AND DRESS. COMMERCAL MOUNTING KIT MUST FOLLOW THE FACTORY
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING APPROVED MOUNTING INSTRUCTIONS A PRODUCT
TUBE OR A RESISTOR RATED AT 1 WATT OR MORE. LEAD MOUNTED TO A SHELF OR PLATFORM MUST RETAIN ITS
TENSION AROUND PROTRUDING METAL SURFACES MUST ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN
BE AVOIDED. SPACERS) TO PROVIDE ADEQUATE AIR FLOW ACROSS
6. ALL CRITICAL COMPONENTS SUCH AS FUSES, THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERS
FLAMEPROOF RESISTORS, CAPACITORS, ETC. MUST BE MUST NOT TOUCH ANY PARTS OR WIRING. PERFORM
REPLACED WITH EXACT FACTORY TYPES, DO NOT USE LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.
REPLACEMENT COMPONENTS OTHER THAN THOSE 5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A
SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT PRODUCT ON SLOPING SHELF OR A TILTED POSITION,
MODIFICATIONS. UNLESS THE PRODUCT IS PROPERLY SECURED.
7. AFTER RE-ASSEMBLY OF THE SET ALWAYS PERFORM AN 6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE
AC LEAKAGE TEST ON ALL EXPOSED METALLIC PARTS OF ON ITS MOUNTING TO THE CART. CAUTION THE
THE CABINET, (THE CHANNEL SELECTOR KNOB, ANTENNA CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART
TERMINALS. HANDLE AND SCREWS) TO BE SURE THE SET WITH SMALL CASTERS ACROSS THRESHOLDS OR DEEP
IS SAFET TO OPERATE WITHOUT DANGER OF ELECTRICAL PILE CARPETS.
SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER 7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR
DURING THIS TEST USE AN AC VOLTMETER, HAVING 5000 STAND WHICH HAS NOT BEEN LISTED BY UNDERWRITERS
OHMS PER VOLT OR MORE SENSITIVITY, IN THE LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC
FOLLOWING MANNER; CONNECT A 1500 OHM 10 WATT MODEL OF TELEVISION RECEIVER OR GENERICALLY
RESISTOR, PARALLELED BY A .15 MFD, 150V AC TYPE APPROVED FOR USE WITH T.V.’S OF THE SAME OR
CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND LARGER SCREEN SIZE.
(WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED 8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION
METALLIC PARTS, ONE AT A TIME. CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS
MEASURE THE AC VOLTAGE ACROSS THE COMBINATION SPROUTING FROM A SINGLE OUTLET CAN LEAD TO
OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR. DISASTROUS CONSEQUENCES TO HOME AND FAMILY.
REVERSE THE AC PLUG AND REPEAT AC VOLTAGE
MEASUREMENTS FOR EACH EXPOSED METALLIC PART.
1-3
SERVICING PRECAUTIONS
CAUTION : Before servicing the A/V Receiver covered by this Electrostatically Sensitive (ES) Devices
service data and its supplements and addends, read and follow the Some semiconductor (solid state) devices can be damaged easily by
SAFETY PRECAUTIONS. NOTE : if unforeseen circumstances static electricity. Such components commonly are called
create conflict between the following servicing precautions and any Electrostatically Sensitive (ES) Devices. Examples of typical Es
of the safety precautions in this publication, always follow the safety devices are integrated circuits and some field effect transistors and
precautions. semiconductor chip components.
Remember Safety First: The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
General Servicing Precautions
1. Always unplug the A/V Receiver AC power cord from the AC 1. Immediately before handling any semiconductor component or
power source before: semiconductor-equipped assembly, drain off any electrostatic
(1) Removing or reinstalling any component, circuit board, charge on your body by touching a known earth ground.
module, or any other assembly. Alternatively, obtain and wear a commercially available
(2) Disconnecting or reconnecting any internal electrical plug or discharging wrist strap device, which should be removed for
other electrical connection. potential shock reasons prior to applying power to the unit under
(3) Connecting a test substitute in parallel with an electrolytic test.
capacitor.
Caution : A wrong part substitution or incorrect polarity installation 2. After removing an electrical assembly equipped with ES devices,
of electrolytic capacitors may result in an explosion hazard. place the assembly on a conductive surface such as aluminum
foil, to prevent electrostatic charge buildup or exposure of the
2. Do not spray chemicals on or near this A/V Receiver or any of its assembly.
assemblies.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
3. Unless specified otherwise in this service data, clean electrical devices.
contacts by applying an appropriate contact cleaning solution to
the contacts with a pipe cleaner, cottontipped swab, or 4. Use only an antistatic solder removal device. Some solder
comparable soft applicator. removal devices not classified a “anti-static” can generate
Unless specified otherwise in this service data, lubrication of electrical charges sufficient to damage ES devices.
contacts is not required.
5. Do not use freonpropelled chemicals. These can generate
4. Do not defeat any plug/socket B+ voltage interlocks with which electrical charge sufficient to damage ES devices.
instruments covered by this service manual might be equipped.
6. Do not remove a replacement ES device from its protective
5. Do not apply AC power to this A/V Receiver and/or any of its package until immediately before you are ready to install it. (Most
electrical assemblies unless all solid-state device heat sinks are replacement ES devices are packaged with leads electrically
correctly installed. shorted together by conductive foam, aluminum foil, or
comparable conductive material).
6. Always connect test instrument ground lead to the appropriate
ground before connecting the test instrument positive lead. Always 7. lmmediately before removing the protective material from the
remove the test instrument ground lead last. leads of a replacement ES device, touch the protective material to
the chassis or circuit assembly into which the device will be
Insulation Checking Procedure installed.
Disconnect the attachment plug from the AC outlet and turn the
power on. Connect an insulation resistance meter(500V) to the Caution : Be sure no power is applied to the chassis or circuit, and
blades of the attachment plug. The insulation resistance between observe all other safety precautions.
each blade of the attachment plug and accessible conductive parts
(Note 1) should be more than 1M-ohm. 8. Minimize bodily motions when handing unpackaged replacement
Note 1 : Accessible Conductive Parts including Metal panels, Input ES devices. (Normally harmless motion such as the brushing
terminals, Earphone jacks, etc. together of your clothes fabric or the lifting of your foot from a
carpeted floor can generate static electricity sufficient to damage
an ES device.)

1-4
SPECIFICATIONS (C715)

AMPLIFIER SECTION
Power output Stereo Mode 25W (6 ohms within rated distortion, 1kHz)
IHF dynamic power (6 ohms) 28W
Total harmonic distortion at rated power 0.15%
Damping factor (6 ohms) >102
Input sensitivity and impedance (Tape IN) 370mV/27kΩ
Frequency response +1 dB/-3dB (Ref. 1 kHz, 10Hz – 80kHz)
Signal/noise ratio, 95dB (Ref. rated power/ 6 ohms A-WTD)
Signal/noise ratio 80dB (Ref. 1W / 6 ohms A-WTD)

TUNER SECTION
AM SECTION
Tuning range 520kHz - 1710kHz (North America version, 10kHz steps)
522kHz -1629kHz (Europe version, 9kHz steps)
Usable sensitivity 60dBuV
S/N ratio 40dB
Total Harmonic Distortion 1.5%
Selectivity 25dB
Frequency response -6dB (Ref. 400Hz, 80Hz – 2.2kHz)

FM SECTION
Tuning range 87.50MHz – 108MHz (50kHz steps)
Usable sensitivity, MONO 10dBuV
S/N Ratio MONO 60dB
S/N Ratio STEREO 55dB
Total Harmonic Distortion, MONO 0.3%
Total Harmonic Distortion, STEREO 0.5%
Frequency response -3dB (Ref. 1 kHz, 30Hz – 12kHz)
Channel Separation 35dB
RDS decode sensitivity 29dBuV

CD SECTION
Output level 1.16V
Frequency response (ref. 0dB 1kHz, 20Hz-20kHz) +1dB
Total harmonic distortion (ref. 1kHz, VIDEO OUT) 0.04%
Signal/Noise ratio (A-weighted, ref. 1kHz VIDEO OUT) 100dB
Channel balance (ref. 0dB 1kHz) 0.5dB
Dynamic range (A-WTD, VIDEO OUT) 82dB
Channel separation 78dB (1kHz)
78dB (10kHz)

PHYSICAL SPECIFICATIONS
Dimensions (W x H x D) 213 x 103 x 324 mm (Net)
213 x 116 x 362 mm (Gross)
Net weight 4.5kg
Shipping weight 6.0kg

Note: Gross dimensions include feet, extended buttons and rear panel terminals.

Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest
information about C 715.

1-5
SPECIFICATIONS (C715 DAB)
AMPLIFIER SECTION
Power output Stereo Mode 25W (6 ohms within rated distortion, 1kHz)
IHF dynamic power (6 ohms) 28W
Total harmonic distortion at rated power 0.15%
Damping factor (6 ohms) >102
Input sensitivity and impedance (Tape IN) 370mV/27kΩ
Frequency response +1 dB/-3dB (Ref. 1 kHz, 10Hz – 80kHz)
Signal/noise ratio, 95dB (Ref. rated power/ 6 ohms A-WTD)
Signal/noise ratio 80dB (Ref. 1W / 6 ohms A-WTD)

TUNER SECTION
AM SECTION
Tuning range 520kHz -1710kHz (North America version, 10kHz steps)
522kHz -1629kHz (Europe version, 9kHz steps)
Usable sensitivity 60dBuV
S/N ratio 40dB
Total Harmonic Distortion 1.5%
Selectivity 25dB
Frequency response -6dB (Ref. 400Hz, 80Hz – 2.2kHz)

FM SECTION
Tuning range 87.50MHz – 108MHz (50kHz steps)
Usable sensitivity, MONO 10dBuV
S/N Ratio MONO 60dB
S/N Ratio STEREO 55dB
Total Harmonic Distortion, MONO 0.3%
Total Harmonic Distortion, STEREO 0.5%
Frequency response -3dB (Ref. 1 kHz, 30Hz – 12kHz)
Channel Separation 35dB
RDS decode sensitivity 29dBuV

DAB SECTION
Tuning range Band III 174MHz – 240MHz
Maximum signal -3dBm
Sensitivity -96dBm
Adjacent Channel Rejection -35dB
Audio Output Stereo 2.5Vp-p
Optical S/PDIF 24 bit sample resolution
48kHz sample rate

CD SECTION
Output level 1.16V
Frequency response (ref. 0dB 1kHz, 20Hz-20kHz) +1dB
Total harmonic distortion (ref. 1kHz, VIDEO OUT) 0.04%
Signal/Noise ratio (A-weighted, ref. 1kHz VIDEO OUT) 100dB
Channel balance (ref. 0dB 1kHz) 0.5dB
Dynamic range (A-WTD, VIDEO OUT) 82dB
Channel separation 78dB (1kHz)
78dB (10kHz)

PHYSICAL SPECIFICATIONS
Dimensions (W x H x D) 213 x 103 x 324 mm (Net)
213 x 116 x 362 mm (Gross)
Net weight 4.5kg
Shipping weight 6.0kg

Note: Gross dimensions include feet, extended buttons and rear panel terminals.

Specifications are subject to change without notice. For updated documentation and features, please log onto www.NADelectronics.com for the latest
information about C 715 DAB.

1-6
DISASSEMBLY

REMOVAL OF TOP COVER

REMOVAL OF FRONT PANEL

1-7
PRINCIPAL PARTS LOCATION

C715DABC

ROD@JDQOBA
STMDQLNCTKD

ONVDQOBA

C@ALNCTKD SQ@MRENQLDQ
DAB Module up to S/N A86C71512400

L@HMOBA
@LOOBA

GD@SRHMJ
BCLDBG@MHRL
CJDKSL2130CCMZ

EQNMSOBA

C715AH & C715C

ROD@JDQOBA
STMDQLNCTKD

ONVDQOBA

SQ@MRENQLDQ

L@HMOBA
@LOOBA

GD@SRHMJ
BCLDBG@MHRL
CJDKSL2130CCMZ

EQNMSOBA

1-8
C715AH EXPLODED VIEW (120V North American version)

C D Mechansim S ony**

**Chart B C715 change LIST

Classification C715C, C715AH, C715DABC CD Mechanism change
Time of application 2008.10 Start
POWER PCB
POWER PCB ASS'Y
DAB MODULE
Rear Panel
Washer
Nut
CD Mechanism CJDWSL11VF S anyo

Program NAD "C515/C715 FIRMWARE LOADER"

Change both mechanism and program simultaneously.
The new Sanyo mechanism will not work with a servo
which has original Sony firmware installed.

1-9 1-10
C715C EXPLODED VIEW (230V European version without DAB receiver)

C D Mechanism S ony**

**Chart B C715 change LIST

Classification C715C, C715AH, C715DABC CD Mechanism change
Time of application 2008.10 Start
POWER PCB
POWER PCB ASS'Y
DAB MODULE
Rear Panel
Washer
Nut
CD Mechanism CJDWSL11VF S anyo

Program NAD C515/C715 FIRMWARE LOADER

Change both mechanism and program simultaneously.
The new Sanyo mechanism will not work with a servo
which has original Sony firmware installed.
.

1-11 1-12
C715DABC EXPLODED VIEW (230V European version with DAB receiver)

W/O F -C onnector See chart B

C D Mechanis m S ony ** See chart B

**Chart B C715 change LIST

Classification C715DABC OLD (DAB 1.0 MODULE) C715C, C715AH, C715DABC CD Mechanism change
Time of application 2007.11 Start to A86C71512400 End 2008.10 Start
POWER PCB CUP12019Z -
POWER PCB ASS'Y COP12019B -
DAB MODULE HNVFS2020V172C -
Rear Panel CKF3A282NK1 -
Washer - -
Nut - -
CD Mechanism CJDKSL2130CCMZ S ony CJDWSL11VF S anyo
NAD_c715_2007_10_13-01.hex /
Program NAD_c715_2008_10-02.hex NAD "C515/C715 FIRMWARE LOADER"
It is possible to use "C515/C715 Change both mechanism and program simultaneously.
FIRMWARE LOADER" with the old The new Sanyo mechanism will not work with a servo
DAB 1.0 MODULE which has original Sony firmware installed.

1-13 1-14
 - /" ÊÓ
 /,
Ê " / /-

" / /-

)# ",/#+ $)!'2!-3  0). $%3#2)04)/. 

. 2

%,%#42)#!, 42/5",%3(//4).' '5)$% 35

$)!'2!-3
£°Ê " Ê 
,
Ê°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° Ӈ39
Ó°Ê7, Ê 
,
Ê °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° Ӈ41
ΰÊ-  
/ Ê 
,
Ê °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° Ӈ43
{°Ê*, / , 1/ "
, -Ê °°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°°° Ӈ47

2-1
 IC BLOCK DIAGRAMS & PIN DESCRIPTION

74HC4066D

Quad bilateral switche

handbook, halfpage nY

handbook, halfpage13 1 5 4 6 8 12 11
1E 1Y 2E 2Y 3E 3Y 4E 4Y nE

1Z 2Z 3Z 4Z VCC VCC
2 3 9 10
MGR257

GND nZ MGR258

Fig.5 Functional diagram. Fig.6 Schematic diagram (one switch).

74VHC08TTR

PIN CONNECTION AND IEC LOGIC SYMBOLS

2-2
AK4554

2-3
ST92F124V

ST92F124V1: Architectural Block Diagram

FLASH
128 Kbytes Ext. MEM.
ADDRESS A[7:0]
DATA D[7:0]
Port0
E3 TM
1 Kbyte
Ext. MEM.
ADDRESS A[10:8]

MEMORY BUS
RAM Ports A[21:11]
4 Kbytes 1,9
P0[7:0]
AS
DS P1[7:3]
RW Fully P1[2:0]
256 bytes
WAIT Prog. P2[7:0]
Register File
NMI I/Os P3[7:4]
DS2 8/16 bits
P3[3:1]
RW CPU
P4[7:4]
P4[3:0]
Interrupt P5[7:0]
INT[6:0] Management P6[5:2,0]
WKUP[15:0] P6.1
ST9 CORE P7[7:0]
OSCIN P8[7:0]
OSCOUT P9[7:0]
RESET RCCU SDA
CLOCK2/8 I2C BUS SCL
INTCLK
CK_AF
STOUT ST. TIMER WATCHDOG WDOUT
REGISTER BUS

HW0SW1
ICAPA0
OCMPA0 MISO
ICAPB0 EF TIMER 0 MOSI
OCMPB0 SPI SCK
EXTCLK0 SS
AVDD
ICAPA1 AVSS
OCMPA1 AIN[15:8]
ICAPB1 EF TIMER 1 ADC
AIN[7:0]
OCMPB1 EXTRG
EXTCLK1
TXCLK
TINPA0 RXCLK
TOUTA0 SIN
MF TIMER 0
TINPB0 SCI M DCD
TOUTB0 SOUT
TINPA1 CLKOUT
TOUTA1 RTS
MF TIMER 1
TINPB1
TOUTB1 RDI
SCI A
TDO
VREG VOLTAGE
REGULATOR

The alternate functions (Italic characters) are mapped on Port 0, Port 1, Port2, Port3, Port4, Port5, Port6, Port7,
Port8 and Port9.

2-4
ST92F124V1: Pin Configuration (Top-view TQFP100)

P7.6/AIN14/WKUP12
P7.5/AIN13/WKUP11
P7.4/AIN12/WKUP3
P7.7/AIN15/7/WKUP13

P7.0/AIN8/CK_AF
P7.3/AIN11
P7.2/AIN10
P7.1/AIN9

P8.7/AIN7
P8.6/AIN6
P8.5/AIN5
P9.1/TDO

HW0SW1

OSCOUT
P9.5/A19
P9.4/A18
P9.3/A17
P9.2/A16

P9.0/RDI

RESET

OSCIN

AVDD
AVSS
VDD
VSS
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76

A20/P9.6 1 75 P8.4/AIN4
A21/P9.7 2 74 P8.3/AIN3
WAIT/WKUP5/P5.0 3 73 P8.2/AIN2
WKUP6/WDOUT/P5.1 4 72 P8.1/AIN1/WKUP15
SIN/WKUP2/P5.2 5 71 P8.0/AIN0/WKUP14
WDIN/SOUT/P5.3 6 70 NC
TXCLK/CLKOUT/P5.4 7 69 P6.5/WKUP10/INTCLK
RXCLK/WKUP7/P5.5 8 68 P6.4/NMI
DCD/WKUP8/P5.6 9 67 P6.3/INT3/INT5
WKUP9/RTS/P5.7 10 66 P6.2/INT2/INT4/DS2
ICAPA1/P4.0 11 65 P6.1/INT6/RW
CLOCK2/P4.1 12 64 P6.0/INT0/INT1/CLOCK2/8
OCMPA1/P4.2
VSS
13
14
ST92F124V1 63
62
P0.7/A7/D7
VDD
VDD 15 61 VSS
ICAPB1/OCMPB1/P4.3 16 60 P0.6/A6/D6
EXTCLK1/WKUP4/P4.4 17 59 P0.5/A5/D5
EXTRG/STOUT/P4.5 18 58 P0.4/A4/D4
SDA/P4.6 19 57 P0.3/A3/D3
WKUP1/SCL/P4.7 20 56 P0.2/A2/D2
ICAPB0/P3.1 21 55 P0.1/A1/D1
ICAPA0/OCMPA0/P3.2 22 54 P0.0/A0/D0
OCMPB0/P3.3 23 53 AS
EXTCLK0/SS/P3.4 24 52 DS
MISO/P3.5 25 51 P1.7/A15

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
VSS
VREG

VREG

NC
SCK/WKUP0/P3.7

RW
TINPA0/P2.0
TINPB0/P2.1
TOUTA0/P2.2
TOUTB0/P2.3
TINPA1/P2.4
TINPB1/P2.5
TOUTA1/P2.6
TOUTB1/P2.7

*VTEST
A8/P1.0
A9/P1.1
A10/P1.2
A11/P1.3
WKUP6

A12/P1.4
A13/P1.5
A14/P1.6
MOSI/P3.6

VDD

* VTEST must be kept low in standard operating mode.

2-5
NAD C715_MCU_Port Table Date : 2007/12/22
pin
Port Name I/O use Name Note
No
1 A20/P9.6 I/O O VFD-CE VFD chip enable pin
2 A21/P9.7 I/O NC
3 WAIT/WKUP5/P5.0 I/O I DAB-DI DAB data in
4 WKUP6/WDOUT/P5.1 I/O I/O DAB-CLK DAB clock
5 SIN/WKUP2/P5.2 I/O I/O DAB-DO DAB data out/update port
6 WDIN/SOUT/P5.3 I/O I DAB-ON update port
7 TXCLK/CLKOUT/P5.4 I/O I update port
8 RXCLK/WKUP7/P5.5 I/O I/O STANBY Standby LED on (active "H")/update port
9 DCD/WKUP8/P5.6 I/O O F-MUTE System mute (active "H")
10 WKUP9/RTS/P5.7 I/O O TCC-CE TCC760 chip enable(USB host I.C)
11 ICAPA1/P4.0 I/O I Option FM frequency step (low : 50kHz, high : 100 kHz)
12 CLOCK2/P4.1 I/O I Option AM frequency step (low : 10kHZ, high : 9kHZ)
13 OCMPA1/P4.2 I/O I Option RDS on,off (low : off, high : on)
14 VSS GND GND
15 VDD VDD +5V
16 ICAPB1/OCMPB1/P4.3 I/O I Option Real time mode(low : 12 hours, high : 24 hours)
17 EXTCLK1/WKUP4/P4.4 I/O I/O R/T SDA Real time i.c serial data
18 EXTRG/STOUT/P4.5 I/O I/O R/T SCL Real time i.c serial clock
19 SDA/P4.6 I/O I R/T IRQ Real time i.c interrupt output
20 WKUP1/SCL/P4.7 I/O O F-STB Function i.c strobe output
21 ICAPB0/P3.1 I/O I Option DAB on,off (low : off, high : on)
22 ICAPA0/OCMPA0/P3.2 I/O I Option RESERVED
23 OCMPB0/P3.3 I/O O TCC-RST TCC760 i.c reset(USB host I.C), active"L"
24 EXTCLK0/SS/P3.4 I/O I GND GND
25 MISO/P3.5 I/O O TCC-DI TCC760 i.c data in
26 MOSI/P3.6 I/O I TCC-DO TCC760 i.c data out
27 SCK/WKUP0/P3.7 I/O I/O TCC-SCLK TCC760 i.c serial clock
28 VREG VREG Stabilization capacitor(s) for internal voltage regulator
29 RW NC
30 TINPA0/P2.0 I/O I PROTECT Protect in, active "L"
31 TINPB0/P2.1 I/O O SP-ON Speaker on, active "H"
32 TOUTA0/P2.2 I/O I H/P-IN Headphone in, active "L"
33 TOUTB0/P2.3 I/O NC
34 TINPA1/P2.4 I/O O T-MUTE Tuner mute, active "H"
35 TINPB1/P2.5 I/O O V-CLK VFD clock pin
36 TOUTA1/P2.6 I/O O V-DATA VFD serial data
37 TOUTB1/P2.7 I/O I BACK-UP Back-up, active "L"
38 VSS GND GND
39 VDD VDD +5V
40 VREG VREG Stabilization capacitor(s) for internal voltage regulator
41 VTEST GND Must be kept low in standard operating mode
42 A8/P1.0 I/O O CD-OPEN-M CD open motor pin
43 A9/P1.1 I/O NC
44 A10/P1.2 I/O O CD-CCE communication chip enalbe with CD DSP
45 A11/P1.3 I/O O CD-BUCK communication clock with CD DSP
46 WKUP6 NC
47 NC NC
48 A12/P1.4 I/O NC
49 A13/P1.5 I/O O CD-POWER optical out change of DAB and CD
50 A14/P1.6 I/O O MT-STBY Motor drive i.c standby pin
51 P1.7/A15 I/O O CD-RST CD dsp reset pin
52 DS NC
53 AS NC
54 P0.0/A0/D0 I/O I/O CD-BUS0 receive data or send command for CD DSP
55 P0.1/A1/D1 I/O I/O CD-BUS1 receive data or send command for CD DSP
56 P0.2/A2/D2 I/O I/O CD-BUS2 receive data or send command for CD DSP
57 P0.3/A3/D3 I/O I/O CD-BUS3 receive data or send command for CD DSP
58 P0.4/A4/D4 I/O I CD-OPEN-SW CD open switch pin
59 P0.5/A5/D5 I/O I CD-CLOSE-SW CD close switch pin
60 P0.6/A6/D6 I/O I CD-LIMIT-SW CD inner switch pin
61 VSS GND GND
62 VDD VDD +5V
63 P0.7/A7/D7 I/O O CD-CLOSE-M CD close motor pin
64 P6.0/INT0/INT1/CLOCK2/8 I/O NC
65 P6.1/INT6/RW I/O I REMOTE Remote in pin
66 P6.2/INT2/INT4/DS2 I/O I RDS-CLK RDS serial clock
67 P6.3/INT3/INT5 I/O I MP3-REQ Request pin for MP3 DSP
68 P6.4/NMI I/O O MP3-STBY 1Mb sram standby pin
69 P6.5/WKUP10/INTCLK I/O NC
70 NC NC
71 P8.0/AIN0/WKUP14 I/O I KEY2 Key input 2
72 P8.1/AIN1/WKUP15 I/O I KEY1 Key input 1

2-6
 73 P8.2/AIN2 I/O NC
74 P8.3/AIN3 I/O I JOG1 Volume encoder in +
75 P8.4/AIN4 I/O I JOG2 Volume encoder in -
76 P8.5/AIN5 I/O NC
77 P8.6/AIN6 I/O NC
78 P8.7/AIN7 I/O NC
79 AVDD VDD +5V
80 AVSS GND GND
81 P7.0/AIN8/CK_AF I/O O POWER-H Power on pin, active "H"
82 P7.1/AIN9 I/O O P/F-DATA Tuner and function i.c serial data
83 P7.2/AIN10 I/O O P/F-CLK Tuner and function i.c serial clock
84 P7.3/AIN11 I/O I PLL-DI Tuner data in pin
85 P7.4/AIN12/WKUP3 I/O O PLL-CE Tuner enable pin
86 P7.5/AIN13/WKUP11 I/O I TUNED-IN Tuned in pin, active"L"
87 P7.6/AIN14/WKUP12 I/O I STEREO-IN Stereo in pin, active"L"
88 P7.7/AIN15/WKUP13 I/O I RDS-DATA RDS serial data
89 VSS GND GND
90 VDD VDD +5V
91 OSCIN I I OSCIN Oscillator in
92 OSCOUT O O OSCOUT Oscillator out
93 RESET I I RESET Reset, active "L"
94 HW0SW1 I I HW0SW1 watchdog HW/SW enabling selection, acitve "H"
95 P9.0/RDI I/O NC
96 P9.1/TDO I/O NC
97 P9.2/A16 I/O NC
98 P9.3/A17 I/O O VFD-DI VFD serial data out
99 P9.4/A18 I/O O VFD-CLK VFD serial clock out
100 P9.5/A19 I/O O VFD-RST VFD reset, active "L"

2-7
FS2020 (Venice) HW Spec 1.2

Keypad External
LCD /Rotary DAC or
encode CODEC

5V

Band III SDRAM

RF (optional)
FS1010
(Chorus)
Serial 384KB Audio
Flash RAM DAC

Serial S/PDIF USB

& RDI I/face
I/Faces
I/faces
Figure 1 - Venice module block diagram (functions in white are on board, in grey are external)

The pin-out for CN1 is as follows:

Pin Description Pin Description
1 5V 23 AUD_SCLK
2 5V 24 AUD_MCLK
3 Audio Left Out 25 LCD DAT 0
4 Audio Ground 26 LCD DAT 1
5 Audio Right Out 27 LCD DAT 2
6 GND 28 LCD DAT 3
7 GND 29 LCD DAT 4
8 USB DM 30 LCD DAT 5
9 USB DP 31 LCD DAT 6
10 GND 32 LCD DAT 7
11 GND 33 LCD_F
12 SPDIF Out 34 LCD_LRS
13 GND 35 LCD_M
14 GND 36 LCD_PE
15 S1_DIN 37 SPDIF In
16 S1_DOUT 38 RDI Out
17 3.3V 39 SCP_CLK
18 3.3V 40 SCP_DAT
19 3.3V 41 PDM Out
20 GND 42 AUD_SDOUT1
21 AUD_SFR 43 AUD_SDOUT2
22 AUD_SDOUT0 44 AUD_SDIN

2-8
 HY57V161610ET

PIN CONFIGURATION

V DD 1 50 V SS
DQ0 2 49 DQ15
DQ1 3 48 DQ14
V SSQ 4 47 VSSQ
DQ2 5 46 DQ13
DQ3 6 45 DQ12
V DDQ 7 44 VDDQ
DQ4 8 43 DQ11
DQ5 9 42 DQ10
V SSQ 10 41 VSSQ
DQ6 11 40 DQ9
DQ7 12 39 DQ8
VDDQ 13 50pin TSOP II 38 VDDQ
LDQM 14 400mil x 825mil 37 NC
/WE 15 0.8mm pin pitch 36 UDQM
/CAS 16 35 CLK
/RAS 17 34 CKE
/CS 18 33 NC
A11 19 32 A9
A10 20 31 A8
A0 21 30 A7
A1 22 29 A6
A2 23 28 A5
A3 24 27 A4
V DD 25 26 VSS

PIN DESCRIPTION
PIN PIN NAME DESCRIPTION

The system clock input. All other inputs are referenced to the SDRAM on the rising
CLK Clock
edge of CLK.

Controls internal clock signal and when deactivated, the SDRAM will be one of the
CKE Clock Enable
states among power down, suspend or self refresh.

CS Chip Select Command input enable or mask except CLK, CKE and DQM
BA Bank Address Select either one of banks during both RAS and CAS activity.

Row Address : RA0 ~ RA10, Column Address : CA0 ~ CA7

A0 ~ A10 Address
Auto-precharge flag : A10
Row Address Strobe,
RAS, CAS and WE define the operation.
RAS, CAS, WE Column Address Strobe, Write
Refer function truth table for details
Enable
LDQM, UDQM Data Input/Output Mask DQM control output buffer in read mode and mask input data in write mode

DQ0 ~ DQ15 Data Input/Output Multiplexed data input / output pin

VDD/VSS Power Supply/Ground Power supply for internal circuit and input buffer

VDDQ/VSSQ Data Output Power/Ground Power supply for DQ

NC No Connection No connection

2-9
FUNCTIONAL BLOCK DIAGRAM

1Mx16 Synchronous DRAM

Self Refresh Counter

Row Addr. Latch/Predecoder

Row Decoder
Refresh Refresh
Interval Timer Counter 512Kx16
Auto/Self Refresh

Bank 0
Ref. Addr.[0:11]

Address[0:10]

Sense AMP & I/O gates

Column Decoder

CLK DQ0
Precharge Address DQ1
CKE

Data Input/Output Buffers

Register DQ2
Row Active DQ3
BA(A11) DQ4
DQ5
State Machine

Column Active Column Addr.

CS DQ6
Latch & Counter
DQ7
RAS Overflow DQ8
Burst Length DQ9
CAS Counter DQ10
DQ11
WE DQ12
DQ13
UDQM DQ14
Column Decoder DQ15
LDQM Sense AMP & I/O gates
Row Addr. Latch/Predecoder

512Kx16
Bank 1

Mode Register Test Mode I/O Control

2-10
 ISL 1208

Block Diagram

SDA SDA
BUFFER Seconds
I2C
INTERFACE RTC
SCL Minutes
SCL CONTROL
BUFFER
LOGIC
Hours

Day of Week
X1
CRYSTAL RTC
Date
OSCILLATOR DIVIDER
X2
Month

VDD Year
POR FREQUENCY
OUT ALARM
CONTROL
VTRIP REGISTERS

SWITCH USER
SRAM
IRQ/
VBAT INTERNAL
FOUT
SUPPLY

Pin Descriptions
PIN
NUMBER SYMBOL DESCRIPTION

1 X1 The X1 pin is the input of an inverting amplifier and is intended to be connected to one pin of an external 32.768kHz
quartz crystal. X1 can also be driven directly from a 32.768kHz source.
2 X2 The X2 pin is the output of an inverting amplifier and is intended to be connected to one pin of an external 32.768kHz
quartz crystal.

3 VBAT This input provides a backup supply voltage to the device. VBAT supplies power to the device in the event that the
VDD supply fails. This pin should be tied to ground if not used.

4 GND Ground.

5 SDA Serial Data (SDA) is a bidirectional pin used to transfer serial data into and out of the device. It has an open drain
output and may be wire OR’ed with other open drain or open collector outputs.

6 SCL The Serial Clock (SCL) input is used to clock all serial data into and out of the device.

7 IRQ/FOUT Interrupt Output/Frequency Output is a multi-functional pin that can be used as interrupt or frequency output pin. The
function is set via the configuration register.

8 VDD Power supply.

2-11
 LC72723M

Pin Assignment (DIP16/MFP16)

Block Diagram

2-12
Pin Descriptions
Pin No. Pin Function I/O Pin circuit type

1 VREF Reference voltage output (Vdda/2) Output

2 MPXIN Base band (multiplex) signal input Input

5 FLOUT Subcarrier output (filter output) Output

6 CIN Subcarrier input (comparator input) Input

3 Vdda Analog system power supply (+5 V) — —

4 Vssa Analog system ground — —

8 XOUT Crystal element output (4.332 MHz) Output

9 XIN Crystal element input (or external reference signal input)

7 TEST Test input

Input

12 MODE Readout mode setting (0: master, 1: slave)

13 RST RDS ID and RAM reset (Active high logic)

14 RDDA RDS data output Output

RDS clock output (master mode)

15 RDCL I/O
RDS clock input (slave mode)

16 RDS-ID/READY RDS ID/ready output (Active low) Output

11 Vddd Digital system power supply (+5 V) — —

10 Vssd Digital system ground — —

2-13
 M29W400D

Logic Diagram TSOP Connections

A15 1 48 A16
VCC
A14 BYTE
A13 VSS
18 15 A12 DQ15A–1
A11 DQ7
A0-A17 DQ0-DQ14
A10 DQ14
A9 DQ6
W DQ15A–1
A8 DQ13
M29W400DT
E BYTE NC DQ5
M29W400DB
NC DQ12
G RB
W DQ4
RP RP 12 M29W400DT 37 VCC
NC 13 M29W400DB 36 DQ11
NC DQ3
RB DQ10
NC DQ2
VSS
A17 DQ9
AI06853
A7 DQ1
A6 DQ8
Signal Names A5 DQ0
A0-A17 Address Inputs A4 G
A3 VSS
DQ0-DQ7 Data Inputs/Outputs A2 E
A1 24 25 A0
DQ8-DQ14 Data Inputs/Outputs
AI06854
DQ15A-1 Data Input/Output or Address Input
Note: 1. NC = Not Connected
E Chip Enable

G Output Enable

W Write Enable

RP Reset/Block Temporary Unprotect

RB Ready/Busy Output

BYTE Byte/Word Organization Select

VCC Supply Voltage

VSS Ground

NC Not Connected Internally

2-14
TA2125AF

4ch VCC
Driver REG
VR RIN FIN STB IN3 IN4 STB
RL4 RL3
REG OUT
N.C.
36 35 34 33 32 31 30 29 28 FIN 27 26 25 24 23 22 21 20 19

Control STBY STBY u 3 u 3 u 3 u 3

Logic

Iref TSD
u 3 u 3 u 3 u 3

1 2 3 4 5 6 7 8 9 FIN 10 11 12 13 14 15 16 17 18
N.C. N.C. GND N.C. N.C.
RL5
RL2 RL1
VCIN IN1 IN2

2-15
Terminal Explanation

No. Symbol Function

1 OUT5A Output terminal H-bridge

2 VM Supply voltage terminal for Logic H-bridge
3 OUT5B Output terminal H-bridge
4 VCIN Input reference voltage 4ch BTL
5 IN1 Input for ch1 4ch BTL
6 N.C. Open ¾
7 N.C. Open ¾
8 N.C. 8, 9, 10, 27, 28, 29 are connected to PW GND (FIN) ¾
9 N.C. 8, 9, 10, 27, 28, 29 are connected to PW GND (FIN) ¾
10 N.C. 8, 9, 10, 27, 28, 29 are connected to PW GND (FIN) ¾
11 IN2 Input for ch2 4ch BTL
12 N.C. Open ¾
13 N.C. Open ¾
14 VCC1 Supply voltage terminal for ch1/ch2 4ch BTL
15 OUT2M Inverted output for ch2 4ch BTL
16 OUT2P Non-inverted output for ch2 4ch BTL
17 OUT1M Inverted output for ch1 4ch BTL
18 OUT1P Non-inverted output for ch1 4ch BTL
19 OUT3P Non-inverted output for ch3 4ch BTL
20 OUT3M Inverted output for ch3 4ch BTL
21 OUT4P Non-inverted output for ch4 4ch BTL
22 OUT4M Inverted output for ch4 4ch BTL
23 VCC2 Supply voltage terminal for ch3/ch4 4ch BTL
24 N.C. Open ¾
25 REG Connection with BASE of PNP Tr Regulator
26 REG OUT Output for regulator (5 V) Regulator
27 N.C. 8, 9, 10, 27, 28, 29 are connected to PW GND (FIN) ¾
28 N.C. 8, 9, 10, 27, 28, 29 are connected to PW GND (FIN) ¾
29 N.C. 8, 9, 10, 27, 28, 29 are connected to PW GND (FIN) ¾
30 REG STBY Standby control for regulator Regulator
31 IN4 Input for ch4 4ch BTL
32 IN3 Input for ch3 4ch BTL
33 STBY Standby control for 4ch BTL 4ch BTL
34 FIN Logic control input H-bridge
35 RIN Logic control input H-bridge
36 VR Supply voltage terminal for motor driver H-bridge

2-16
TC94A54MFG

1. Pin Configuration and Block Diagram

SBAD/RFDC
AVDD3
XVDD3

VDD15

AVSS3
XVSS3

VSS15

SBOK
ZDET

VREF

RFRP
SBSY
GPIN

SFSY

DMO

TEZI
FMO

RFZI
TRO

FOO

TEI

FEI
IPF
XO

XI

25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

DVSS3 26 CLOCK 100 FTE

GEN.

+
-
5-bit 10-bit
PWM
RO 27
R-2R DAC SAR ADC 99 TNI
SUBCODE
DEMODULA TE
DVDD3 28 TION 98 TPI
ANA. 1-bit
CIRCUIT
LPF DAC
DVR 29 97 FPI1

LO 30 96 FPI2
FE
DVSS3 31 95 FNI1

VSS3 32 SERVO 94 FNI2

CONTROL
-
+

VDD3 33 93 RVSS3

VDDM 34 92 MDI
APC
ROM
VSS15 35 DIGITAL EQ 91 LDO
AUTO ADJ.
RAM
BUS0 36 90 RVDD3
RF Block
BUS1 37 89

CPU ADRRESS CIRCUIT

I/F
BUS2 38 88 PNSEL
RF
BUS3 39 87 RFO
CORRECTION CIRCUIT

CAV SERVO CLV SERVO

BUCK 40 RFDC 86

16k
/CCE 41 RAM AGC 85

Pull-up
/RST 42 84

STBY 43 83

SYNC SIGNAL PROTECTION

VDDT 44 82
EFM DEMODULATION

FGIN 45 VRO 81

IO0 46 80

IO1 47 RFEQ 79

TESTD 48 RFRP 78

VSSP 49 EFM SLICE 77

DIGITAL AUDIO PLL

OUT OUT AWRC VCO
VCOI 50 TMAX 76

+
-

51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
DOUT

BCKI

LRCKI
AOUT

TMAX

VCOREF
PVREF
BCKO

AWRC

PDO

VCOF
LRCKO

LPFO
VDDP

TESTC

AIN

LPFN
PIO0

PIO1

PIO2

PIO3

VDD15

VSS15

PVDD3

PVSS3

2-17
3. Pin Functions
Note: 3AI/F : 3 V circuit analog input/output pin
3I/F : 3 V circuit digital input/output pin
1.5AI/F : 1.5 V circuit analog input/output pin
Pin
Pin name I/O Description Remark
No.
I Input pin for the RF ripple zero-cross To be connected to the
1 RFZI
3AI/F signal. RFRP via 0.033 uF.
2 AVSS3 — Grounding pin for 3.3 V analog circuits. —
O
3 RFRP RF ripple signal output pin. —
3AI/F
O
4 FEI Focus error signal input pin.
3AI/F
O Monitor pin for various
5 SBAD/RFDC Subbeam addition signal input pin.
3AI/F signals.
O
6 TEI Tracking error signal input pin.
3AI/F
I Input pin for tracking error signal To be connected to the
7 TEZI
3AI/F zero-cross. TEI via 0.033 uF.
8 AVDD3 — Supply voltage pin for 3.3 V analog circuit. —
O
9 FOO Focus equalizer output pin. —
3AI/F
O
10 TRO Tracking equalizer output pin. —
3AI/F
Connected to the VRO
O and PVREF within the IC.
11 VREF Analog reference supply voltage pin.
3AI/F To be connected to 0.1
uF.
O PWM ternary output
12 FMO Speed error/feed equalizer output pin.
3AI/F (AVDD3, GND, and
O
13 DMO Disc equalizer output pin. VREF).
3AI/F
Pin for outputting the subcode block sync
signal. It is "H" at position S1 when the
SBSY O “H” at S1 when Subcode
14 subcode sync signal is detected.
(SPCK) 3I/F Sync is detected.
(CD Processor Status Read
Clock(176.4KHz) output)
Pin for outputting the CRCC check result of
a subcode Q data check. It is "H" when the
SBOK
check result is OK.
(FOK) O
15 (Focus OK signal) —
(CLCK) 3I/F
(Input/output pin for the clock used in
(MBOV)
reading the subcode P to W data.)
(CD Buffer memory overflow output)
Correction flag output pin.
IPF O "H" if the AOUT pin outputs an
16 —
(SPDA) 3I/F uncorrectable symbol in C2 correction.
(CD Processor Status signal output)

2-18
Pin
Pin name I/O Description Remark
No.
Pin for outputting the playback frame sync
7.35kHz
signal.
(At this pin, flags in the
SFSY (Emphasis flag output pin.
DSP and PLL-circuit clock
(EMPH) O ENPH on: "H". EMPH off: "L".
17 can be monitored, using
(LOCK) 3I/F The output polarity can be switched, using a
microcontroller commands.
(MONIT) command.)
The pin also outputs text
(LOCK signal)
data serially.)
(Pin for monitoring signals in the DSP.)
Output pin for zero detection flag for the
ZDET 1-bit DAC.
O Valid also for 1-bit DAC
18 (DATA) (Pin for outputting subcode P to W data)
3I/F external inputs.
(COFS) (Error Correstion Frame Clock 7.35kHz
output)
I/O General-purpose I/O
19 GPIN General-purpose I/O㧔DSP㧕
3I/F (input after a reset).
1.5V grounding pin dedicated to the Digital
20 VSS1 — —
circuit.
1.5 V supply voltage pin dedicated to the
21 VDD1 — —
Digital circuit.
Grounding pin for the system clock
22 XVSS3 — —
oscillation circuit.
I Input pin for the system clock oscillation
23 XI —
3AI/F circuit.
O Output pin for the system clock oscillation
24 XO Input to the internal MCK.
3AI/F circuit.
3.3 V supply voltage pin for the system
25 XVDD3 — —
clock oscillation circuit.
26 DVSS3 — Grounding pin for the 1-bit DAC. —
O Output pin for normal R-channel data for No capacitor is required at
27 RO
3AI/F the 1-bit DAC. the DVR pin unless the
28 DVDD3 — 3.3 V supply voltage pin for the 1-bit DAC. built-in 1-bit DAC is used.
3.3 V must be applied
29 DVR O Reference voltage pin for the 1-bit DAC. across the DVDD3 and
DVSS3 pins, however.
O Output pin for normal L-channel data for
30 LO
3AI/F the 1-bit DAC. —
31 DVSS3 — Grounding pin for the 1-bit DAC.
3.3 V grounding pin dedicated to the I/F
32 VSS3 — —
circuit.
3.3 V supply voltage pin dedicated to the I/F
33 VDD3 — —
circuit.
1.5 V supply voltage pin dedicated to the
34 VDDM — —
DSP/1Mbit SRAM circuit.
1.5V grounding pin dedicated to the
35 VSS1 — —
DSP/1Mbit SRAM circuit.

2-19
Pin
Pin name I/O Description Remark
No.
I/O
36 BUS0
3I/F
I/O To be fixed at "H" or "L"
37 BUS1 Data input/output pin for the microcontroller
3I/F when communication is
interface.
I/O not in progress, so that the
38 BUS2 pin will not become HiZ.
3I/F
I/O
39 BUS3
3I/F
I Clock input pin for the microcontroller
40 BUCK To be fixed at "H" when
3I/F interface.
communication is not in
Chip enable signal input pin for the
I progress, so that the pin
41 /CCE microcontroller interface. BUS3 to BUS0
3I/F will not become HiZ.
are active if this pin is "L".
Reset signal input pin. The internal
registers and servo section registers are
I To be connected to 0.1
42 /RST reset, respectively, when the reset signal is
3I/F uF.
"L" and on the positive-going edge of the
reset signal.
I STANBY control pin dedicated to the
43 STBY —
3I/F DSP/1Mbit SRAMcircuit.
3.3 V supply voltage pin dedicated to the
44 VDDT — —
Digital I/O circuit.
I FG signal input pin for CAV.
45 FGIN —
3AI/F CLV: "L". CAV: FG input.
General-purpose input/output pins.
I/O (Pin for outputting the playback speed General-purpose I/O (input
46 IO0A㧔/HSO㧕
3I/F mode flag.) after a reset).
/UHSO /HSO Playback speed The playback speed mode
H H Normal speed flag output can be
IO1A I/O H L 2 times switched, using command
47
㧔/UHSO㧕 3I/F L H 4 times bits.

I
48 TESTD DSP/Test input pin. Usually fixed at "L". —
3I/F
1.5 V grounding pin dedicated to the
48 VSSP — —
DSP/VCO circuit.
O PD output pin dedicated to the
50 VCOI —
1.5AI/F DSP/VCOcircuit.
1.5 V supply voltage pin dedicated to the
51 VDDP — —
DSP/VCO circuit.
I
52 TESTC CD/ Test input pin. Usually fixed at "L". —
3I/F
I/O
53 PIO0 General-purpose I/O㧔CD/DSP㧕
3I/F
I/O
54 PIO1 General-purpose I/O㧔CD/DSP㧕
3I/F General-purpose I/O (input
I/O after a reset).
55 PIO2 General-purpose I/O㧔DSP㧕
3I/F
I/O
56 PIO3 General-purpose I/O㧔DSP㧕
3I/F

2-20
Pin
Pin name I/O Description Remark
No.
Digital-out output pin. Digital data for up to
O
57 DOUT double speed can be output when a As per CP-1201
3I/F
frequency of 16.9344 MHz is used.
Audio data output pin. Which bit is first
O
58 AOUT (MSB first or LSB first) can be selected, —
3I/F
using a command.
O Bit clock output pin. 32fs, 48fs, and 64fs Normal speed
59 BCK
3I/F can be selected, using a command. : 32fs = 1.4112 MHz
LR channel clock output pin. "L" for the
O L-channel and "H" for the R-channel. The
60 LRCK Normal speed: 44.1 kHz
3I/F output polarity can be inverted, using a
command.
I
61 AIN 1-bit DAC external input: AIN
3I/F
I
62 BCKI 1-bit DAC external input: BCKI 1-bit DAC external input
3I/F
I
63 LRCKI 1-bit DAC external input: LRCKI
3I/F
1.5 V supply voltage pin dedicated to the
64 VDD1 —
DSP circuit.
1.5 V grounding pin dedicated to the DSP
65 VSS1 —
circuit.
O
66 AWRC VCO control pin for active wide range. Controllable in CLV/CAV.
3AI/F
3.3 V supply voltage pin dedicated to the
67 PVDD3 — —
PLL circuit.
Quaternary output
O Pin for outputting a phase difference signal (PVDD3, HiZ, VSS, and
68 PDO
3AI/F between the EFM signal and PLCK signal.
PVREF).
Pin for outputting the result of TMAX
O Ternary output
69 TMAX detection.
3AI/F (PVDD3, VSS, and Hiz).
The TMAX pin output the same signal.
The resistance side is
I Pin for receiving an inverted output of the
70 LPFN connected. See an
3AI/F PLL-circuit low-pass filter amp.
applicable circuit diagram.
The capacitor side is
O Pin for the PLL-circuit low-pass filter amp
71 LPFO connected. See an
3AI/F output.
applicable circuit diagram.
Connected to the VREF
1.65 V reference supply voltage pin and PVREF within the IC.
72 PVREF —
dedicated to the PLL circuit. A 0.1 uF capacitor is
connected.
O
73 VCOF VCO filter pin. —
3AI/F
To be connected to the
I Input pin for the VCO center frequency
74 VCOREF PVREF if the AWRC is not
3AI/F reference level.
used.

2-21
Pin
Pin name I/O Description Remark
No.
3.3 V grounding pin dedicated to the PLL
75 PVSS3 — —
circuit.
A capacitor to be
EFM slice level output pin.
O connected is selected
76 SLCO For both analog and digital slice modes,
3AI/F according to the servo
the output impedance # 2.5 k:.
operation band.
RF signal input pin.
I
77 RFI The input resistance can be selected, using Zin: 20k:, 10k:, 5k:
3AI/F
a command.
I
78 RFRPI RF ripple signal input pin. —
3AI/F
To be connected to the
O RFRPI via 0.1 uF and to
79 RFEQO RF equalizer circuit output pin.
3AI/F the RFI via 4700 pF or
higher.
I Pin for connecting a reference current To be connected to 22 k:
80 RESIN
3AI/F generating resistance. and 680 pF in parallel.
Connected to the VREF
O and PVREF within the IC.
81 VRO 1.65 V reference voltage output pin.
3AI/F To be connected to 0.1 uF
and 100 uF.
Reference voltage output pin for the APC To be connected to 0.1
82 VMDIR —
circuit. uF.
O To be connected to
83 TESTR LPF pin for RFEQO offset correction.
3AI/F 0.015 uF or higher.
I
84 INVSEL Test pin, usually fixed at "L". —
3AI/F
I Pin for RF signal amplitude adjustment
85 AGCI —
3AI/F amp input.
I
86 RFDCI RF signal peak detection input pin. —
3AI/F
To be connected directly
O to the RFDCI.
87 RFO RF signal generation amp output pin.
3AI/F To be connected to the
AGCI via 0.1 uF.
I
88 PNSEL Test pin, usually fixed at "H".
3AI/F
O External connection pin for the RF signal To be kept open when the
89 EQSET
3AI/F equalizer. RFEQ is used.
3.3V Supply voltage pin for the RFamp core
90 RVDD3 — —
section
O
91 LDO Laser diode amp output pin.
3AI/F
I
92 MDI Monitor photodiode amp input pin. Reference to 178 mV (typ.)
3AI/F
3.3 V grounding pin for the RF amp core
93 RVSS3 — —
section.

2-22
 Pin
Pin name I/O Description Remark
No.
I Main beam input pin.
94 FNI2 —
3AI/F Connected to PIN diode C.
I Main beam input pin.
95 FNI1 —
3AI/F Connected to PIN diode A.
I Main beam input pin.
96 FPI2 —
3AI/F Connected to PIN diode D.
I Main beam input pin.
97 FPI1 —
3AI/F Connected to PIN diode B.
I Subbeam amp input pin.
98 TPI —
3AI/F Connected to PIN diode F.
I Subbeam amp input pin.
99 TNI —
3AI/F Connected to PIN diode E.
Focus/tracking signal output.
O Switchable using a
100 FTE (Test pin for servo characteristic
3AI/F command.
measurement.)
Note: "3AI/F : 3 V circuit analog input/output pin."
"3I/F : 3 V circuit digital input/output pin."
"1.5AI/F : 1.5 V circuit analog input/output pin."

2-23
TC9163

2-24
2-25
2-26
TCC760

Block Diagram
USB_DP / GPIO_B[26], USB_DN / GPIO_B[27]
USBH_DP / GPIO_B[28], USBH_DN / GPIO_B[29]

PLL & XIN, XOUT

USB1.1 XTIN, XTOUT
Boot ROM CLK Generator
Host / Device XFILT
(4KB)
TCO2 / GPIO_A[11]
TCO5 / GPIO_A[8]
Timers /
ECC TCO1 / GPIO_A[7]
SRAM Counters TCO4 / GPIO_A[4]
DQM[0:1] / XA[21:20] Generation TCO0 / GPIO_A[3]
DQS[1:0] / XA[19:18] (64KB) TCO3 / GPIO_A[0]
ND_CLE / XA[17] Interrupt
ND_ALE / SD_nRAS / XA[16] EXINT[3:0] /
SD_nCAS / XA[15] APB Controller GPIO_A[15:12]
SD_BA[1:0] / XA[14:13] Bridge
XA[12:0]
Ext. Memory
XD[15:0] Interface

AHB

APB
nOE, nWE, nCS[3:0]
GSIO GPIO_A[11:0]
SD_nCS, SD_CKE AHB Arbiter
SD_CLK GPIO_A[15:0]
ND_nWE
AHB Wrapper GPIO_B[29:21]
IDE_nCS1 GPIO GPIO_B[9:7]
READY GPIO_B[5:0]
DMA GPIO_D[17:15]
ARM940T
(2-channel) UT_TX / GPIO_B[8]
UART/IrDA
UT_RX / GPIO_B[9]

TDI, TMS, TCK JTAG

nTRST, TDO DAI (I2S) GPIO_A[11:10]
for I2C GPIO_A[9:8]
GPIO_D[17:16]
Video Input CODEC
GPIO_D[21:15]
GPIO_A[3:0] Interface & ADIN0
CD-DSP ADC ADIN2
ADIN4

DAO / GPIO_B[24] GPIO_A[3] / CDAI

MCLK / GPIO_B[23] GPIO_A[2] / CLRCK
BCLK / GPIO_B[21] GPIO_A[1] / CBCLK
LRCKO / GPIO_B[22]
DAI / GPIO_B[25]

Functional Block Diagram of TCC760

2-27
Pin Description

The status of the following GPIO pins are latched at the rising edge of nRESET and used to determine the system bus width and
boot mode. External devices must not drive output levels onto these pins during reset period.

Pin Name State during reset State after reset During normal function with DAI enabled
GPIO_A[9] / BW[1]
Bus Width Configuration Input Normal GPIO Input Mode GPIO Output Mode for 2-Wire Interface Clock and Data
GPIO_A[8] / BW[0]
GPIO_B[24] / BM[2] DAO (I2S Digital Audio Output)
GPIO_B[22] / BM[1] Boot Mode Configuration Input Normal GPIO Input Mode LRCK (I2S Word Clock Output)
GPIO_B[21] / BM[0] BCLK (I2S Bit Clock Output)
Refer to sections “BOOTING PROCEDURE” and “MEMORY CONTROLLER” for detailed description of BW[1:0] and BM[2:0].

In case of the TCC763, TCC764 and TCC766, GPIO_B[22:21]/BM[1:0] signals are connected to internal audio
CODEC pins which have on-chip pull-down resistor. If external pull-up resistors are required for these pins,
4.7k: is recommended.

The TCC76x is a CMOS device. Floating level on input signals cause unstable device operation and abnormal
current consumption. Pull-up or pull-down resistors should be used appropriately for input or bidirectional pins.

Notation
I: Input
O: Output
I/O: Bidirectional
AI: Analog Input
AO: Analog Output
PWR: Power
GND: Ground

TCC760 Pin Description

Table 1.2 TCC760 Pin Description

Signal Name Shared Signal Pin # Type Description – TCC760
External Memory Interface Pins
SD_CKE GPIO_B[0] 56 I/O SDRAM Clock Enable signal. Active high. / GPIO_B[0]
SDRAM Clock / GPO. SD_CLK can be used as a general
SD_CLK GPO 44 I/O purpose output. Refer to section “MEMORY CONTROLLER”.
(MCFG register Bit[3] and Bit[1])
Chip select signal for SDRAM, Active low / Inverted SD_CLK for
SD_nCS SD_nCLK / GPIO_B[1] 46 I/O
DDR SDRAM / GPIO_B[1]
XA[21:20] DQM[0:1] 43:42 I/O External Bus Address Bit [21:20] / Data I/O Mask 0, 1
XA[19:18] DQS[1:0] 40:39 I/O External Bus Address Bit [19:18] / DDR SDRAM Data Strobe [1:0]
XA[17] ND_CLE 38 I/O External Bus Address Bit [17] / CLE for NAND Flash
External Bus Address Bit [16] / SDRAM RAS signal / ALE
XA[16] SD_nRAS / ND_ALE 37 I/O
for NAND Flash
XA[15] SD_nCAS 36 I/O External Bus Address Bit [15] / SDRAM CAS signal
XA[14] SD_BA[1] 35 I/O External Bus Address Bit [14] / SDRAM Bank Address 1
XA[13] SD_BA[0] 34 I/O External Bus Address Bit [13] / SDRAM Bank Address 0.
XA[12:7] 31:26
I/O External Bus Address Bits [12:0]
XA[6:0] 23:17
XD[15:9] 15:9 I/O External Bus Data Bit [15:0]
XD[8:4] 6:2

2-28
Signal Name Shared Signal Pin # Type Description – TCC760
XD[3:0] 128:125
External Bus Chip Select [3:0] / NAND Flash Output Enable
NCS[3:0] ND_nOE[3:0] / GPIO_B[5:2] 50:47 I/O
[3:0] / GPIO_B[5:2]
ND_nWE GPIO_B[7] 57 I/O NAND flash WE. Active low. / GPIO_B[7]
nWE 58 I/O Static Memory Write Enable signal. Active low.
nOE 59 I/O Static Memory Output Enable signal. Active low.
READY 73 I Ready information from external device.
USB/UART/IrDA Interface Pins
USB_DP GPIO_B[26] 51 I/O USB Function D+ signal / GPIO_B[26]
USB_DN GPIO_B[27] 52 I/O USB Function D- signal / GPIO_B[27]
USBH_DP GPIO_B[28] 53 I/O USB Host D+ signal / GPIO_B[28]
USBH_DN GPIO_B[29] 54 I/O USB Host D- signal / GPIO_B[29]
UART or IrDA TX data / GPIO_B[8] / DDR SDRAM Chip
UT_TX GPIO_B[8] / SD_nCS 60 I/O
Select
UT_RX GPIO_B[9] / IDE_nCS1 61 I/O UART or IrDA RX data / GPIO_B[9] / IDE Chip Select 1
Audio Interface Pins
BCLK GPIO_B[21] / BM[0] 62 I/O I2S Bit Clock / GPIO_B[21] / Boot Mode Bit 0
LRCK GPIO_B[22] / BM[1] 63 I/O I2S Word Clock / GPIO_B[22] / Boot Mode Bit 1
MCLK GPIO_B[23] 66 I/O I2S System Clock / GPIO_B[23]
I2S Digital Audio data Output / GPIO_B[24] / Boot Mode
DAO GPIO_B[24] / BM[2] 67 I/O
Bit 2
DAI GPIO_B[25] 68 I/O I2S Digital Audio data Input / GPIO_B[25]
CD DSP Interface Pins
CBCLK GPIO_A[1] 105 I/O CD Data Bit Clock Input / GPIO_A[1]
CLRCK GPIO_A[2] 106 I/O CD Data Word Clock Input / GPIO_A[2]
CDAI GPIO_A[3] 107 I/O CD Data Input / GPIO_A[3]
External Interrupt Pins
EXINT[3] GPIO_A[15] 124 I/O External Interrupt Request [3] / GPIO_A[15]
EXINT[2:0] GPIO_A[14:12] / FGPIO[14:12] 123:121 I/O External Interrupt Request [2:0] / GPIO_A[14:12] / FGPIO[14:12]
Camera Interface Pins
CISHS GPIO_D[17] 92 I/O Horizontal Sync. Input / GPIO_D[17]
CISVS GPIO_D[16] 91 I/O Vertical Sync. Input / GPIO_D[16]
CISCLK GPIO_D[15] 90 I/O Clock Input / GPIO_D[15]
CISD[7:4] GPIO_D[21:18] 96:93
I/O Data Input[7:0] / GPIO_D[21:18], GPIO_A[3:0]
CISD[3:0] GPIO_A[3:0] 107:104
General Purpose I/O Pins
GPIO_A[15] EXINT[3] 124 I/O GPIO_A[15] / External Interrupt 3
GPIO_A[14:12] EXINT[2:0] / FGPIO[14:12] 123:121 I/O GPIO_A[15:12] / External Interrupt 3 ~ 0 / Fast GPIO bits 14 ~ 12
GPIO_A[11:8] / Bus Width bits 1 ~ 0 / General Purpose Serial I/O 2
GPIO_A[11] SDI2 / FGPIO[11] / SCL
Fast GPIO bits 11 ~ 8 / I2C signals.
GPIO_A[10] FRM2 / FGPIO[10] / SDA
118:115 I/O The status of BW[1:0] is latched at the rising edge of nRESET and
GPIO_A[9] / BW[1] SCK2 / FGPIO[9] / SCL
used to determine external bus width. Refer to section “MEMORY
GPIO_A[8] / BW[0] SDO2 / FGPIO[8] / SDA
CONTROLLER” for BW[1:0] description.
SDI1 / FGPIO[7] 114
FRM1 / FGPIO[6] 113
GPIO_A[7:4] I/O GPIO_A[7:4] / General Purpose Serial I/O 1 / Fast GPIO bits 7 ~ 4
SCK1 / FGPIO[5] 111
SDO1 / FGPIO[4] 108
SDI0 / CDAI / FGPIO[3]
GPIO_A[3:1] / General Purpose Serial I/O 0 / CD Interface Signals /
GPIO_A[3:1] FRM0 / CLRCK / FGPIO[2] 107:105 I/O
Fast GPIO bits 3 ~ 1
SCK0 / CBCLK / FGPIO[1]

2-29
Signal Name Shared Signal Pin # Type Description – TCC760
GPIO_A[0] / General purpose serial I/O 0 Serial Data Output
GPIO_A[0] SDO0 / FGPIO[0] 104 I/O
FGPIO[0]
GPIO_B[29:28] USBH_DN, USBH_DP 54:53 I/O GPIO_B[29:28] / USBH_DN, USBH_DP
GPIO_B[27:26] USB_DN, USB_DP 52:51 I/O GPIO_B[27:26] / USB_DN, USB_DP
GPIO_B[25] DAI 68 GPIO_B[25:21] / Boot Mode bits 2 ~ 0 / I2S Interface Signals.
GPIO_B[24] / BM[2] DAO 67 The status of BM[2:0] is latched at the rising edge of nRESET and
GPIO_B[23] MCLK 66 I/O used to determine the system boot mode. Refer to sections
GPIO_B[22] / BM[1] LRCK 63 “BOOTING PROCEDURE” and “MEMORY CONTROLLER” for
GPIO_B[21] / BM[0] BCLK 62 detailed description on BM[2:0].
GPIO_B[9] UT_RX 61 I/O GPIO_B[9 ] / UART RX Signal
GPIO_B[8] UT_TX / SD_nCS 60 I/O GPIO_B[8] / UART TX Signal / DDR SDRAM Chip Select
GPIO_B[7] ND_nWE 57 I/O GPIO_B[7] / Write Enable for NAND Flash
GPIO_B[5:2] nCS[3:0] 50:47 I/O GPIO_B[5:2] / External Chip Select 3 ~ 0
GPIO_B[1] / Chip select for SDRAM / Inverted Clock for DDR
GPIO_B[1] SD_nCS / SD_nCLK 46 I/O
SDRAM.
GPIO_B[0] SD_CKE 56 I/O GPIO_B[0] / SDRAM clock control
GPIO_D[21:18] / Fast GPIO bits 13 ~10 / Camera Interface Data
GPIO_D[21:18] FGPIO[13:10] / CISD[7:4] 96:93 I/O
Inputs 3 ~ 0. Internal pull-up resistors are enabled at reset.
GPIO_D[17] FGPIO[9] / SCL / CISHS 92 I/O GPIO_D[17] / Fast GPIO bit 9 / I2C SCL / Camera Interface Hsync.
GPIO_D[16] FGPIO[8] / SDA / CISVS 91 I/O GPIO_D[16] / Fast GPIO bit 8 / I2C SDA / Camera Interface Vsync.
GPIO_D[15] CISCLK 90 I/O GPIO_D[15] / Camera Interface Clock
ADC Input Pins
ADIN_0 - 82 AI General purpose multi-channel ADC input 0
ADIN_2 - 83 AI General purpose multi-channel ADC input 2
ADIN_4 - 84 AI General purpose multi-channel ADC input 4
Clock Pins
XIN - 74 I Main Crystal Oscillator Input for PLL. 12MHz Crystal
must be used if USB Boot Mode is required. Input
voltage must not exceed VDD_OSC (1.95V max).
XOUT - 75 O Main Crystal Oscillator Output for PLL
XFILT - 78 AO PLL filter output
XTIN - 69 I Sub Crystal Oscillator Input. 32.768kHz is recommended.
Input voltage must not exceed VDD_OSC (1.95V max).
XTOUT - 70 O Sub Crystal Oscillator Output
Mode Control Pins
MODE1 - 98 I Mode Setting Input 1. Pull-down for normal operation.
PKG1 - 89 I Package ID1, Pull-up for normal operation.
nRESET - 72 I System Reset. Active low.
JTAG Interface Pins
TDI - 99 I JTAG serial data input for ARM940T
TMS - 100 I JTAG test mode select for ARM940T
TCK - 101 I JTAG test clock for ARM940T
TDO - 102 I/O JTAG serial data output for ARM940T. External pull-up resistor is
required to prevent floating during normal operation.
nTRST - 103 I JTAG reset signal for ARM940T. Active low.
Power Pins
VDDIO - 112 PWR Digital Power for I/O (1.8V ~ 3.3V)
76
33
16

2-30
Signal Name Shared Signal Pin # Type Description – TCC760
VDD_USB - 64 PWR Power for USB I/O (3.3V)
VDD_OSC - 71 PWR Digital Power for Oscillators (1.8V)
VDDI - 119 PWR Digital Power for Internal Core (1.8V)
109
41
24
7
VDDI_ADC - 87 PWR Digital Power for ADC (1.8V)
VDDA_ADC - 81 PWR Analog Power for ADC (3.3V)
VDDA_PLL - 77 PWR Analog & Digital Power for PLL (1.8V)
VSSIO - 97 GND Digital Ground for I/O
65
45
32
1
VSSI - 120 GND Digital Ground for Internal
110
55
25
8
VSSI_ADC - 88 GND Digital Ground for ADC
VBBA_ADC - 86 GND Analog Ground for ADC
VSSA_ADC - 85 GND Analog Ground for ADC
VBBA_PLL - 80 GND Analog Ground for PLL
VSSA_PLL - 79 GND Analog Ground for PLL

2-31
 TDA 7292

Typical Application Circuit in Split Supply

+VS

1000μF
15K 1μF
MUTE/
ST-BY 3
5
IN (L) 7
+ 4 OUT (L)
1μF -
18K 4.7Ω
RL (L)
8 IN- (L)
100nF
15K 18K
GND 9 560Ω
+5V μP
10 IN- (R) 560Ω

18K
1μF - 2 OUT (R)
IN (R) 11
+
4.7Ω
1 6 RL (R)
-VS 100nF

1000μF
D94AU085

April 2005
This is preliminary information on a new product now in development. Details are subject to change without notice.

Pin Connection (Top view)

11 IN+(1)
10 IN-(1)
9 GND
8 IN-(2)
7 IN+(2)
6 -VS
5 MUTE/St-By
4 OUTPUT(2)
3 +VS
2 OUTPUT(1)
1 -VS

TAB CONNECTED TO PIN 6 D95AU316

2-32
TDA 7313

PIN CONNECTION (Top view)

2-33
 C11 5.6K R2 C17
100nF 2.7nF
C9 2.2μF
100nF 100nF
C14 C15
OUT(L) IN(L) LOUD(L) BOUT(L) BIN(L) TREBLE(L)
BLOCK DIAGRAM

17 16 12 19 18 4
SPKR
ATT
RB 25 OUT LEFT
FRONT
3x
2.2μF MUTE
C1 L1 15 L1
SPKR
C2 L2 14 L2 VOL ATT
LEFT BASS TREBLE
INPUTS + LOUD 23 OUT LEFT
C3 L3 13 L3 REAR
MUTE

28
INPUT SCL
SELECTOR SERIAL BUS DECODER + LATCHES 27
+ GAIN SDA BUS

2-34
26
DIGGND
C4 R3 9 R3
SPKR
RIGHT C5 R2 10 R2 VOL ATT
BASS TREBLE
INPUTS + LOUD 24 OUT RIGHT
C6 R1 11 R1 FRONT
MUTE
3x
2.2μF
SPKR
ATT
22 OUT RIGHT
RB
REAR
SUPPLY
MUTE
2 3 1 7 6 8 21 20 5
VS AGND CREF OUT(R) IN(R) LOUD(R) BOUT(R) BIN(R) TREBLE(R) D98AU888
C7 22μF 100nF 100nF
C12 C13
C8 2.2μF
100nF 5.6K R1 2.7nF
C10 C16
 ELECTRICAL TROUBLESHOOTING GUIDE

32:(5&+(&.

123RZHU/(' 12)/'

&KHFN)IXVH
&KHFN)IXVH

YES YES ,V9DSSOLHG

,V9DSSOLHG &KHFNWKH)URQW 0DLQ &KHFNWKH)URQW 0DLQ9)' WR&1SLQ‫ڧ‬
WR&1SLQ‫"ڪ‬ SRZHURQ&LUFXLW &LUFXLW DQG9DSSOLHG
WR&1SLQ‫"ڦ‬

NO NO

YES <(6
&KHFN4 ' &KHFNWKH)URQW 0DLQ
&KHFNWKH%1:)DQG &KHFN4 4RI0DLQ
RISRZHU3&% SRZHURQ&LUFXLW
FDUGFDEOH 3&%

12

YES
,VDFYROWDJJ
&KHFNWKH7 DSSOLHGWR%1
‫"ڧڦڥ‬

NO NO

&KDQJH &KHFN3RZHU7UDQVIRUPHU

)25$//32:(5,6215(/$<5<0867%(21͐
 $7),5673/($6(&+(&.5< )86()
12±$0332:(5 9&& 12±9

YES YES
,Vs9&&DSSOLHG &KHFN3RZHU$PS ,VsDSSOLHG
&KHFNPDLQFLUFXLW
WR&1‫"ڥ ڡ‬ &LUFXLW WR&1‫"ڣ ڡ‬

NO NO

&KHFN&1 ,V$&9DSSOLHG
WR%1‫"ګ ڪ‬

NO

&KHFN3RZHU7UDQVIRUPHU

2-35
86%3$57&+(&.

32:(521

,QVHUWD86%0HPRU\LQWKH
6(7

YES
86%LFRQDSSHDU
2.
RQWKH9)'"

,V9DSSOLHGWR YES
%1ձ" &KHFN86%9

YES

NO
,V9DSSOLHG FKHFN7&&UHVHW
WR,&‫ڣ‬SLQ" FLUFXLW

YES

&KHFN7&&DQG
0&8LQWHUIDFH
'$%3$57&+(&.

32:(521

YES
$XWRVFDQDSSHDURQWKH 2.
9)'"

YES
86%DSSHDURQWKH
2.
9)'"

NO

,V99 NO
DSSOLHGWR%1 &KHFN&1
SLQ"

YES

&KHFN:)‫ڧڥ‬
SLQ

2-36
$8',23$57&+(&. 1223(1&/26(

DESCRIPTION: CD tray may not open or close.

REASON: The tray sense switch can grow tiny conductive
$8',2287387 1R23(1&/26( "whiskers" across the contact pads shorting the switch and
preventing the tray from opening/closing.

SOLUTION: Change the value of R101 and R102 from 18K to 470 ohm to
increase the current flow across each contact switch pads eliminating the
“WHISKERS”. Resistor 470R 1/8w SMD 0605

32:(521 3XVK23(1&/26(.H\

NO NO
,V ,V,QGLFDWLRQRI &KHFN23(1&/26(
3RZHU s9&&s9 &KHFN3RZHUOLQH ),3'LVSOD\ .H\RQ0&8
9 FRUUHFWO\" 23(1"

YES YES

NO NO
&KHFNVSRQ ,V,&SLQ &KHFN,&SLQ
,V5<21" +" VKRUWRURSHQ
FLUFXLW

YES YES

NO NO
,V)XQFWLRQPXWH ,V,&SLQ+
&KHFNIXQFWLRQ " &KHFN,&
ZRUNHGFRUUHFO\" PXWHFLUFXLW

YES YES

NO NO
,V9&55(&287387 ,V,&SLQ+
" &KHFNSDWHUQVKRUWRURSHQ
&KHFN,& )XQFLWRQ,&

YES YES

&KHFN,& 9ROXPH,& 5HSODFH&'WUDYHUVHXQLW

2-37
1R3/$<%$&.

1R3OD\EDFN

3XVK23(1&/26(.H\

NO
&1SLQ
&KHFN,&,&
+ǿ/ǿ+"

YES

NO
/D]HURQ" &KHFN4RU
5HSODFH&'SLFNXS

YES

NO
/HQ]XSGRZQ" &KHFN,&SLQ
VLJQDO

YES
YES

NO
&KHFN,&SLQ
3OD\',6&EXW VLJQDO &KHFN,&
QRWQRUPDO

YES
YES

NO
,V&1
5HSODFH&'WUDYHUVHXQLW FRQQHFWHG &KHFN,&RU&DUG&DEOH
FRUUHFWO\"

YES

5HSODFH&'WUDYHUVHXQLW

2-38
1. BLOCK DIAGRAM

2-39 2-40
2. WIRING DIAGRAM

2-41 2-42
3. SCHEMATIC DIAGRAM
MAIN PART

470

470
2-43 2-44
POWER & POWER AMP & KEYBOARD PART

2-45 2-46
4. PRINTED CIRCUIT BOARDS
MAIN PCB DATA VIEW (TOP)

2-47 2-48
MAIN PCB DATA VIEW (BOTTOM)

2-49 2-50
POWER PCB DATA VIEW

2-51 2-52
 SECTION 3
ELECTRICAL PARTS LIST
MAIN PCB ASS'Y ( DABC : COP12018B, C : COP12018C, AH : COP12018D )
CUP12018Z PCB , MAIN C715(291X216, FR-4, 2 ARRAY)

REF NO. PART NO. DESCRIPTION REMARKS

CUP12018Z MAIN BOARD
C101 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C103 CCUS1H222KC CAP , CHIP 2200PF 50V K
C104 CCUS1H222KC CAP , CHIP 2200PF 50V K
C108 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C110 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C111 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C113 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C114 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C115 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C116 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C117 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C120 CCUS1H101JA CAP , CHIP 100PF 50V J
C121 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C122 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C126 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C127 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C128 CCUS1H471JA CAP , CHIP 470PF 50V J
C129 CCUS1H471JA CAP , CHIP 470PF 50V J
C130 CCUS1H333KC CAP , CHIP 0.033UF 50V K
C131 CCUS1H333KC CAP , CHIP 0.033UF 50V K
C132 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C133 CCUS1H150JA CAP , CHIP 15PF 50V J
C134 CCUS1H150JA CAP , CHIP 15PF 50V J
C135 CCUS1H102KC CAP , CHIP 1000PF 50V K
C136 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C137 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C138 CCUS1H222KC CAP , CHIP 2200PF 50V K
C140 CCUS1H153KC CAP , CHIP 0.015UF 50V K
C141 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C142 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C143 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C144 CCUS1H470JA CAP , CHIP 47PF 50V J
C145 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C146 CCUS1H472KC CAP , CHIP 4700PF 50V K
C147 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C149 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C150 CCUS1H681JA CAP , CHIP 680PF 50V J
C151 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C152 CCUS1H153KC CAP , CHIP 0.015UF 50V K
C153 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C154 CCUS1H680JA CAP , CHIP 68PF 50V J
C155 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C156 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C157 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C401 CCUS1H101JA CAP , CHIP 100PF 50V J
C403 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C405 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C408 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C409 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C411 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C412 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C413 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C414 CCUS1H561JA CAP , CHIP 560PF 50V J
C415 CCUS1H561JA CAP , CHIP 560PF 50V J
C416 CCUS1H220JA CAP , CHIP 22PF 50V J
C417 CCUS1H220JA CAP , CHIP 22PF 50V J
C418 CCUS1H220JA CAP , CHIP 22PF 50V J
C422 CCUS1H221JA CAP , CHIP 220PF 50V J
C423 CCUS1H221JA CAP , CHIP 220PF 50V J
C424 CCUS1H221JA CAP , CHIP 220PF 50V J
C425 CCUS1H221JA CAP , CHIP 220PF 50V J
C426 CCUS1H221JA CAP , CHIP 220PF 50V J
C429 CCUS1H150JA CAP , CHIP 15PF 50V J
C430 CCUS1H150JA CAP , CHIP 15PF 50V J
C431 CCUS1H101JA CAP , CHIP 100PF 50V J C715DABC ONLY
C432 CCUS1H101JA CAP , CHIP 100PF 50V J C715DABC ONLY
C433 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C434 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C435 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C436 CCUS1H104KC CAP , CHIP 0.1UF 50V K

3-1
C437 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C438 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C439 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C451 CCUS1H102KC CAP , CHIP 1000PF 50V K
C452 CCUS1H102KC CAP , CHIP 1000PF 50V K
C454 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C456 CCUS1H561JA CAP , CHIP 560PF 50V J
C457 CCUS1H220JA CAP , CHIP 22PF 50V J
C458 CCUS1H220JA CAP , CHIP 22PF 50V J
C459 CCUS1H102KC CAP , CHIP 1000PF 50V K
C501 CCUS1H181JA CAP , CHIP 180PF 50V J
C502 CCUS1H181JA CAP , CHIP 180PF 50V J
C503 CCUS1H181JA CAP , CHIP 180PF 50V J
C504 CCUS1H181JA CAP , CHIP 180PF 50V J
C505 CCUS1H181JA CAP , CHIP 180PF 50V J
C506 CCUS1H181JA CAP , CHIP 180PF 50V J
C507 CCUS1H181JA CAP , CHIP 180PF 50V J
C508 CCUS1H181JA CAP , CHIP 180PF 50V J
C509 CCUS1H181JA CAP , CHIP 180PF 50V J
C510 CCUS1H181JA CAP , CHIP 180PF 50V J
C511 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C512 CCUS1H153KC CAP , CHIP 0.015UF 50V K
C513 CCUS1H223KC CAP , CHIP 0.022UF 50V K
C514 CCUS1H223KC CAP , CHIP 0.022UF 50V K
C517 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C518 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C519 CCUS1H221JA CAP , CHIP 220PF 50V J
C520 CCUS1H221JA CAP , CHIP 220PF 50V J
C524 CCUS1H181JA CAP , CHIP 180PF 50V J
C525 CCUS1H181JA CAP , CHIP 180PF 50V J
C545 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C548 CCUS1H181JA CAP , CHIP 180PF 50V J
C549 CCUS1H331JA CAP , CHIP 330PF 50V J
C553 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C554 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C555 CCUS1H181JA CAP , CHIP 180PF 50V J
C556 CCUS1H181JA CAP , CHIP 180PF 50V J
C702 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C703 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C704 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C705 CCUS1H220JA CAP , CHIP 22PF 50V J
C706 CCUS1H220JA CAP , CHIP 22PF 50V J
C707 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C709 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C710 CCUS1H220JA CAP , CHIP 22PF 50V J
C711 CCUS1H220JA CAP , CHIP 22PF 50V J
C712 CCUS1H220JA CAP , CHIP 22PF 50V J
C717 CCUS1H222KC CAP , CHIP 2200PF 50V K
C718 CCUS1H222KC CAP , CHIP 2200PF 50V K
C721 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C722 CCUS1H220JA CAP , CHIP 22PF 50V J
C723 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C724 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C725 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C726 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C727 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C728 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C729 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C730 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C732 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C734 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C735 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C901 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C911 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C912 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C918 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C920 CCUS1H103KC CAP , CHIP 0.01UF 50V K
C921 CCUS1H104KC CAP , CHIP 0.1UF 50V K
C923 CCUS1H103KC CAP , CHIP 0.01UF 50V K
D101 CVD1SS355T DIODE , CHIP
D401 HVDUDZS4.3BSR DIODE , ZENER 4.3V, 1712 TYPE
D402 CVD1SS355T DIODE , CHIP
D403 CVD1SS355T DIODE , CHIP
D404 CVD1SS355T DIODE , CHIP
D405 CVD1SS355T DIODE , CHIP
D406 CVD1SS355T DIODE , CHIP

3-2
D501 CVD1SS355T DIODE , CHIP
D502 CVD1SS355T DIODE , CHIP
D901 HVDUDZS27BSR DIODE , ZENER 27V, 1712 TYPE
D902 HVDUDZS9.1BSR DIODE , ZENER 9.1V, 1712 TYPE
D905 HVDUDZS4.3BSR DIODE , ZENER 4.3V, 1712 TYPE
D906 CVD1SS355T DIODE , CHIP
IC11 HVITC94A54MFG01 I.C , DIGITAL SERVO
IC12 HVITA2125AFG I.C , MOTOR DRIVER
IC41 HVIST92F124V1T6 I.C , MCU ST92F124V1T6
IC42 HVIISL1208IU8ZT I.C , RTC
IC43 HVIRH5VT28C I.C , RESET
IC45 HVILC72723M IC , PLL (RDS)
IC51 HVINJM2068MDTE1 I.C , OP AMP NJM2068MD-TE1
IC52 HVITDA7313NDTR I.C , VOLUME
IC53 HVITC9163CFG I.C , FUNCTION SW
IC72 HVIM29W400DT70N 4M FLASH
IC73 HVI57V161610ET7 SDRAM 16M 7NS HY57V161610ET-7
IC74 KVITCC760HC01AG 32BIT RISC CPU
IC75 HVIAK4554VT I.C , CODEC(16BIT)
IC76 HVI74VHC08TTR I.C , AND-GATE 74VHC08
IC96 HVILM1117S-ADJ I.C , REGULATOR LM1117-ADJ
IC97 HVILM1117S-ADJ I.C , REGULATOR LM1117-ADJ
IC98 HVILM1117S-ADJ I.C , REGULATOR LM1117-ADJ
L101 CLQ08E100KRZ COIL , CHIP 10uH, 2012
L102 CLQ08E100KRZ COIL , CHIP 10uH, 2012
Q402 HVTKRA107ST T.R , CHIP KRA107S
Q403 HVTKTD1304T T.R , CHIP KTD1304
Q404 HVTKTD1304T T.R , CHIP KTD1304
Q406 HVTKRC107S T.R , CHIP KRC107S C715DABC ONLY
Q407 HVTKRC107S T.R , CHIP KRC107S C715DABC ONLY
Q408 HVTKRC107S T.R , CHIP KRC107S C715DABC ONLY
Q409 HVTKRA107ST T.R , CHIP KRA107S
Q410 HVTKRC107S T.R , CHIP KRC107S
Q501 HVTKTD1304T T.R , CHIP KTD1304
Q502 HVTKTD1304T T.R , CHIP KTD1304
Q503 HVTKRA107ST T.R , CHIP KRA107S
R101 CRJ10DJ471T RES , CHIP 1608 SIZE
R102 CRJ10DJ471T RES , CHIP 1608 SIZE
R103 CRJ10DJ183T RES , CHIP 1608 SIZE
R104 CRJ10DJ471T RES , CHIP 1608 SIZE
R105 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R106 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R107 CRJ10DJ682T RES , CHIP 1608 SIZE
R108 CRJ10DJ332T RES , CHIP 1608 SIZE
R109 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R110 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R111 CRJ10DJ105T RES , CHIP 1608 SIZE
R112 CRJ10DJ104T RES , CHIP 1608 SIZE
R113 CRJ10DJ271T RES , CHIP 1608 SIZE
R114 CRJ10DJ271T RES , CHIP 1608 SIZE
R115 CRJ10DJ473T RES , CHIP 1608 SIZE
R116 CRJ10DJ473T RES , CHIP 1608 SIZE
R117 CRJ10DJ562T RES , CHIP 1608 SIZE
R118 CRJ10DJ562T RES , CHIP 1608 SIZE
R119 CRJ10DJ562T RES , CHIP 1608 SIZE
R120 CRJ10DJ562T RES , CHIP 1608 SIZE
R121 CRJ10DJ562T RES , CHIP 1608 SIZE
R122 CRJ10DJ562T RES , CHIP 1608 SIZE
R123 CRJ10DJ562T RES , CHIP 1608 SIZE
R124 CRJ10DJ562T RES , CHIP 1608 SIZE
R125 CRJ10DJ562T RES , CHIP 1608 SIZE
R127 CRJ10DJ104T RES , CHIP 1608 SIZE
R128 CRJ10DJ104T RES , CHIP 1608 SIZE
R129 CRJ10DJ102T RES , CHIP 1608 SIZE
R130 CRJ10DJ221T RES , CHIP 1608 SIZE
R131 CRJ10DJ102T RES , CHIP 1608 SIZE
R132 CRJ10DJ104T RES , CHIP 1608 SIZE
R133 CRJ10DJ104T RES , CHIP 1608 SIZE
R134 CRJ10DJ104T RES , CHIP 1608 SIZE
R138 CRJ10DJ562T RES , CHIP 1608 SIZE
R139 CRJ10DJ154T RES , CHIP 1608 SIZE
R140 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R141 CRJ10DJ223T RES , CHIP 1608 SIZE
R142 CRJ10DJ153T RES , CHIP 1608 SIZE
R143 CRJ10DJ473T RES , CHIP 1608 SIZE
R144 CRJ10DJ683T RES , CHIP 1608 SIZE

3-3
R145 CRJ10DJ223T RES , CHIP 1608 SIZE
R146 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R148 CRJ10DJ100T RES , CHIP 1608 SIZE
R149 CRJ10DJ100T RES , CHIP 1608 SIZE
R401 CRJ10DJ562T RES , CHIP 1608 SIZE
R402 CRJ10DJ562T RES , CHIP 1608 SIZE
R403 CRJ10DJ102T RES , CHIP 1608 SIZE
R404 CRJ10DJ102T RES , CHIP 1608 SIZE
R405 CRJ10DJ100T RES , CHIP 1608 SIZE
R406 CRJ10DJ100T RES , CHIP 1608 SIZE
R407 CRJ10DJ102T RES , CHIP 1608 SIZE
R408 CRJ10DJ103T RES , CHIP 1608 SIZE
R409 CRJ10DJ153T RES , CHIP 1608 SIZE
R410 CRJ10DJ153T RES , CHIP 1608 SIZE
R411 CRJ10DJ562T RES , CHIP 1608 SIZE
R412 CRJ10DJ562T RES , CHIP 1608 SIZE
R413 CRJ10DJ104T RES , CHIP 1608 SIZE
R414 CRJ10DJ183T RES , CHIP 1608 SIZE
R415 CRJ10DJ183T RES , CHIP 1608 SIZE
R416 CRJ10DJ330T RES , CHIP 1608 SIZE
R417 CRJ10DJ562T RES , CHIP 1608 SIZE
R418 CRJ10DJ473T RES , CHIP 1608 SIZE
R419 CRJ10DJ271T RES , CHIP 1608 SIZE
R420 CRJ10DJ102T RES , CHIP 1608 SIZE
R421 CRJ10DJ271T RES , CHIP 1608 SIZE
R422 CRJ10DJ271T RES , CHIP 1608 SIZE
R423 CRJ10DJ183T RES , CHIP 1608 SIZE
R424 CRJ10DJ183T RES , CHIP 1608 SIZE
R425 CRJ10DJ103T RES , CHIP 1608 SIZE
R426 CRJ10DJ103T RES , CHIP 1608 SIZE
R427 CRJ10DJ183T RES , CHIP 1608 SIZE
R428 CRJ10DJ183T RES , CHIP 1608 SIZE
R429 CRJ10DJ183T RES , CHIP 1608 SIZE
R430 CRJ10DJ183T RES , CHIP 1608 SIZE
R431 CRJ10DJ183T RES , CHIP 1608 SIZE
R432 CRJ10DJ470T RES , CHIP 1608 SIZE
R433 CRJ10DJ470T RES , CHIP 1608 SIZE
R434 CRJ10DJ470T RES , CHIP 1608 SIZE
R435 CRJ10DJ470T RES , CHIP 1608 SIZE
R436 CRJ10DJ470T RES , CHIP 1608 SIZE
R437 CRJ10DJ183T RES , CHIP 1608 SIZE
R438 CRJ10DJ183T RES , CHIP 1608 SIZE
R439 CRJ10DJ183T RES , CHIP 1608 SIZE C715DABC, C715C
R444 CRJ10DJ183T RES , CHIP 1608 SIZE C715AH ONLY
R440 CRJ10DJ183T RES , CHIP 1608 SIZE
R441 CRJ10DJ183T RES , CHIP 1608 SIZE
R442 CRJ10DJ183T RES , CHIP 1608 SIZE
R448 CRJ10DJ183T RES , CHIP 1608 SIZE C715DABC ONLY
R450 CRJ10DJ183T RES , CHIP 1608 SIZE C715C, C715AH
R449 CRJ10DJ183T RES , CHIP 1608 SIZE
R451 CRJ10DJ153T RES , CHIP 1608 SIZE
R452 CRJ10DJ153T RES , CHIP 1608 SIZE
R453 CRJ10DJ103T RES , CHIP 1608 SIZE
R454 CRJ10DJ102T RES , CHIP 1608 SIZE
R455 CRJ10DJ102T RES , CHIP 1608 SIZE
R456 CRJ10DJ183T RES , CHIP 1608 SIZE
R457 CRJ10DJ102T RES , CHIP 1608 SIZE
R501 CRJ10DJ221T RES , CHIP 1608 SIZE
R502 CRJ10DJ221T RES , CHIP 1608 SIZE
R503 CRJ10DJ221T RES , CHIP 1608 SIZE
R504 CRJ10DJ221T RES , CHIP 1608 SIZE
R505 CRJ10DJ102T RES , CHIP 1608 SIZE
R506 CRJ10DJ102T RES , CHIP 1608 SIZE
R507 CRJ10DJ221T RES , CHIP 1608 SIZE
R508 CRJ10DJ221T RES , CHIP 1608 SIZE
R509 CRJ10DJ102T RES , CHIP 1608 SIZE
R510 CRJ10DJ102T RES , CHIP 1608 SIZE
R511 CRJ10DJ473T RES , CHIP 1608 SIZE
R512 CRJ10DJ473T RES , CHIP 1608 SIZE
R513 CRJ10DJ473T RES , CHIP 1608 SIZE
R514 CRJ10DJ473T RES , CHIP 1608 SIZE
R515 CRJ10DJ473T RES , CHIP 1608 SIZE
R516 CRJ10DJ473T RES , CHIP 1608 SIZE
R517 CRJ10DJ473T RES , CHIP 1608 SIZE
R518 CRJ10DJ473T RES , CHIP 1608 SIZE
R519 CRJ10DJ473T RES , CHIP 1608 SIZE

3-4
R520 CRJ10DJ473T RES , CHIP 1608 SIZE
R521 CRJ10DJ102T RES , CHIP 1608 SIZE
R522 CRJ10DJ101T RES , CHIP 1608 SIZE
R523 CRJ10DJ123T RES , CHIP 1608 SIZE
R524 CRJ10DJ103T RES , CHIP 1608 SIZE
R525 CRJ10DJ153T RES , CHIP 1608 SIZE
R526 CRJ10DJ104T RES , CHIP 1608 SIZE
R527 CRJ10DJ562T RES , CHIP 1608 SIZE
R528 CRJ10DJ562T RES , CHIP 1608 SIZE
R529 CRJ10DJ473T RES , CHIP 1608 SIZE
R530 CRJ10DJ473T RES , CHIP 1608 SIZE
R531 CRJ10DJ102T RES , CHIP 1608 SIZE
R532 CRJ10DJ102T RES , CHIP 1608 SIZE
R533 CRJ10DJ822T RES , CHIP 1608 SIZE
R534 CRJ10DJ822T RES , CHIP 1608 SIZE
R535 CRJ10DJ222T RES , CHIP 1608 SIZE
R536 CRJ10DJ222T RES , CHIP 1608 SIZE
R537 CRJ10DJ273T RES , CHIP 1608 SIZE
R538 CRJ10DJ273T RES , CHIP 1608 SIZE
R539 CRJ10DJ102T RES , CHIP 1608 SIZE
R540 CRJ10DJ102T RES , CHIP 1608 SIZE
R541 CRJ10DJ4R7T RES , CHIP 1608 SIZE
R542 CRJ10DJ4R7T RES , CHIP 1608 SIZE
R545 CRJ10DJ272T RES , CHIP 1608 SIZE
R546 CRJ10DJ272T RES , CHIP 1608 SIZE
R547 CRJ10DJ562T RES , CHIP 1608 SIZE
R548 CRJ10DJ562T RES , CHIP 1608 SIZE
R549 CRJ10DJ683T RES , CHIP 1608 SIZE
R550 CRJ10DJ683T RES , CHIP 1608 SIZE
R551 CRJ10DJ4R7T RES , CHIP 1608 SIZE
R552 CRJ10DJ4R7T RES , CHIP 1608 SIZE
R553 CRJ10DJ473T RES , CHIP 1608 SIZE
R554 CRJ10DJ473T RES , CHIP 1608 SIZE
R555 CRJ10DJ221T RES , CHIP 1608 SIZE
R556 CRJ10DJ221T RES , CHIP 1608 SIZE
R557 CRJ10DJ272T RES , CHIP 1608 SIZE
R558 CRJ10DJ472T RES , CHIP 1608 SIZE
R559 CRJ10DJ272T RES , CHIP 1608 SIZE
R702 CRJ10DJ103T RES , CHIP 1608 SIZE
R704 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R705 CRJ10DJ103T RES , CHIP 1608 SIZE
R706 CRJ10DJ755T RES , CHIP 1608 SIZE
R708 CRJ10DJ103T RES , CHIP 1608 SIZE
R709 CRJ10DJ103T RES , CHIP 1608 SIZE
R710 CRJ10DJ103T RES , CHIP 1608 SIZE
R711 CRJ10DJ472T RES , CHIP 1608 SIZE
R714 CRJ10DJ473T RES , CHIP 1608 SIZE
R715 CRJ10DJ473T RES , CHIP 1608 SIZE
R716 CRJ10DJ473T RES , CHIP 1608 SIZE
R717 CRJ10DJ102T RES , CHIP 1608 SIZE
R718 CRJ10DJ103T RES , CHIP 1608 SIZE
R719 CRJ10DJ103T RES , CHIP 1608 SIZE
R720 CRJ10DJ103T RES , CHIP 1608 SIZE
R721 CRJ10DJ103T RES , CHIP 1608 SIZE
R722 CRJ10DJ103T RES , CHIP 1608 SIZE
R723 CRJ10DJ101T RES , CHIP 1608 SIZE
R724 CRJ10DJ101T RES , CHIP 1608 SIZE
R725 CRJ10DJ101T RES , CHIP 1608 SIZE
R726 CRJ10DJ101T RES , CHIP 1608 SIZE
R727 CRJ10DJ101T RES , CHIP 1608 SIZE
R728 CRJ10DJ103T RES , CHIP 1608 SIZE
R729 CRJ10DJ472T RES , CHIP 1608 SIZE
R730 CRJ10DJ472T RES , CHIP 1608 SIZE
R731 CRJ10DJ472T RES , CHIP 1608 SIZE
R732 CRJ10DJ472T RES , CHIP 1608 SIZE
R733 CRJ10DJ102T RES , CHIP 1608 SIZE
R734 CRJ10DJ102T RES , CHIP 1608 SIZE
R901 CRJ10DJ561T RES , CHIP 1608 SIZE
R902 CRJ10DJ331T RES , CHIP 1608 SIZE
R903 CRJ10DJ681T RES , CHIP 1608 SIZE
R904 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R905 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R906 CRJ10DJ181T RES , CHIP 1608 SIZE
R907 CRJ10DJ331T RES , CHIP 1608 SIZE
R908 CRJ10DJ182T RES , CHIP 1608 SIZE
R910 CRJ10DJ474T RES , CHIP 1608 SIZE

3-5
R911 CRJ10DJ471T RES , CHIP 1608 SIZE
R912 CRJ10DJ101T RES , CHIP 1608 SIZE
R914 CRJ10DJ0R0T RES , CHIP 1608 SIZE
R917 CRJ10DJ122T RES , CHIP 1608 SIZE
R918 CRJ10DJ181T RES , CHIP 1608 SIZE
R919 CRJ10DJ473T RES , CHIP 1608 SIZE
R920 CRJ10DJ330T RES , CHIP 1608 SIZE
R921 CRJ10DJ271T RES , CHIP 1608 SIZE
R922 CRJ10DJ103T RES , CHIP 1608 SIZE
C102 CCEA1CH470T CAP , ELECT 47UF 16V
C105 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C106 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C107 CCEA1HH220T CAP , ELECT 22UF 50V
C109 CCEA1CH101T CAP , ELECT 100UF 16V
C112 CCEA1CH470T CAP , ELECT 47UF 16V
C123 CCEA1CH101T CAP , ELECT 100UF 16V
C139 CCEA1CH470T CAP , ELECT 47UF 16V
C148 CCEA1CH101T CAP , ELECT 100UF 16V
C402 CCEA1CH101T CAP , ELECT 100UF 16V
C404 CCEA1CH221T CAP , ELECT 220UF 16V
C406 CCEA1CH101T CAP , ELECT 100UF 16V
C410 CCEA1HH100T CAP , ELECT 10UF 50V
C453 CCEA1CH101T CAP , ELECT 100UF 16V
C455 CCEA1HH100T CAP , ELECT 10UF 50V
C515 CCEA1CH470T CAP , ELECT 47UF 16V
C516 CCEA1CH470T CAP , ELECT 47UF 16V
C521 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C522 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C523 CCEA1HH100T CAP , ELECT 10UF 50V
C526 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C527 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C528 HCQI1H104JZT CAP , MYLAR 0.1UF 50V J
C529 HCQI1H104JZT CAP , MYLAR 0.1UF 50V J
C530 HCQI1H104JZT CAP , MYLAR 0.1UF 50V J
C531 HCQI1H104JZT CAP , MYLAR 0.1UF 50V J
C532 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C533 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C534 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C535 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C536 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C537 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C538 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C539 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C540 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C541 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C542 HCQI1H272JZT CAP , MYLAR 2700PF 50V J
C543 HCQI1H272JZT CAP , MYLAR 2700PF 50V J
C544 CCEA1HH220T CAP , ELECT 22UF 50V
C546 CCEA1CH101T CAP , ELECT 100UF 16V
C547 CCEA1CH101T CAP , ELECT 100UF 16V
C551 CCEA1CH470T CAP , ELECT 47UF 16V
C552 CCEA1CH470T CAP , ELECT 47UF 16V
C559 CCEA1HH100T CAP , ELECT 10UF 50V
C713 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C714 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C715 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C716 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C719 CCEA1HH2R2T CAP , ELECT 2.2UF 50V
C720 CCEA1CH471T CAP , ELECT 470UF 16V
C736 CCEA1CH471T CAP , ELECT 470UF 16V
C903 CCEA1CH470T CAP , ELECT 47UF 16V
C905 CCEA1CH470T CAP , ELECT 47UF 16V
C907 CCEA1CH470T CAP , ELECT 47UF 16V
C910 CCEA1HH470T CAP , ELECT 47UF 50V
C913 CCEA1HH220T CAP , ELECT 22UF 50V
C914 CCEA1CH221T CAP , ELECT 220UF 16V
C917 CCEA1CH101T CAP , ELECT 100UF 16V
C922 CCEA1CH471T CAP , ELECT 470UF 16V
D903 CVD1N4003SRT DIODE , RECT 1N4003
D904 CVD1N4003SRT DIODE , RECT 1N4003
D907 CVD1N4003SRT DIODE , RECT 1N4003
D908 CVD1N4003SRT DIODE , RECT 1N4003
IC55 HVIKA78L08AZT I.C , REGULATOR KA78LXXAZTA, +8V
Q101 HVTKTA1266YT T.R TKTA1266YT
Q405 HVTKSB811YT T.R KSB811Y
Q901 HVTKSC2316YT T.R KSC2316Y

3-6
Q902 HVTKSC2316YT T.R KSC2316Y
CN11 CJP05GA19ZY WAFER , STRAIGHT
CN12 CJP06GA19ZY WAFER , STRAIGHT
CN13 CJP16GA117ZY WAFER
CN21 CJP13GA117ZY WAFER , CARD CABLE
CN31 CJP05GA19ZY WAFER , STRAIGHT
CN41 CJP05GA19ZY WAFER , STRAIGHT
CN42 CJP07GA19ZY WAFER , STRAIGHT
CN51 CJP03GA19ZY WAFER , STRAIGHT
CN61 CJP03GA19ZY WAFER , STRAIGHT
CN83 CJP05GA01ZY WAFER
CN94 CJP11GA01ZY WAFER
C421 CCESDX5R5V334U CAP , DYNA 0.33F 5.5V
C902 CCEA1AH102E CAP , ELECT 1000UF 10V
C909 CCEA1JH101E CAP , ELECT 100UF 63V
C919 CCEA1EH222E CAP , ELECT 2200UF 25V
C924 CCEA1AH102E CAP , ELECT 1000UF 10V
IC22 CVIKA78R05VA I.C , REGULATOR + 5V
IC90 CVIKIA7808A I.C , REGULATOR + 8V
IC99 CVIKIA7805A I.C , REGULATOR + 5V
JK51 CJJ4M056W JACK , BOARD
JK52 CJJ4P019W JACK , RCA
JK53 CJJ4R020W JACK , BOARD
L401 KLZ9H001Z BEAD , CORE
WF64 CJP15GA115ZY WAFER , CARD CABLE
WF81 CJP17GA117ZY WAFER
X101 HOX16934E120C CRYSTAL 16.934MHZ
X401 HOX04000E150C CRYSTAL 4MHZ
X402 HOX00032K120I CRYSTAL 32.768KHZ
X403 HOX04332E200C CRYSTAL 4.332KHZ
X701 HOX12000E200C CRYSTAL 12MHZ

3-7
POWER PCB ASS'Y ( DABC : COP12019B, C : COP12019C, AH : COP12019D )
CUP12019Z PCB , POWER C715(240X251, FR-1)

REF NO. PART NO. DESCRIPTION REMARKS

CUP12018-1 USB BOARD
BN83 CWZC715BN83 SHIEL WIRE ASS'Y(5P, 250MM)
C821 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
JK83 HJJ9X001Z JACK, USB

REF NO. PART NO. DESCRIPTION REMARKS

CUP12018-2 PHONE BOARD
BK85 CMC1A324 BRACKET , JACK C715
BN41 CWB2B005180EN WIRE ASS'Y(5P, 180MM)
BN51 CWZC715BN51 SHIEL WIRE ASS'Y(3P, 400MM)
C816 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C818 HCBS1C472MXT CAP , CERAMIC 4700PF 16V M
C819 HCBS1C472MXT CAP , CERAMIC 4700PF 16V M
JK81 CJJ2E028Z JACK , HEADPHONE(3.5mm, GOLD) PJ-323AG-7
JK82 CJJ2E028Z JACK , HEADPHONE(3.5mm, GOLD) PJ-323AG-7

REF NO. PART NO. DESCRIPTION REMARKS

CUP12018-3 FRONT BOARD
BK83 CMD1A468 BRACKET , FLT
BK84 CMD1A468 BRACKET , FLT
C801 HCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z
C802 HCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z
C803 HCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z
C804 HCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z
C805 HCBS1H221KBT CAP , CERAMIC 220PF 50V K
C806 HCBS1H221KBT CAP , CERAMIC 220PF 50V K
C807 HCBS1H221KBT CAP , CERAMIC 220PF 50V K
C808 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C809 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C810 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C811 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C812 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C813 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C814 HCBS1H390JT CAP , CERAMIC 39PF 50V J
C817 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C820 CCEA1CH470T CAP , ELECT 47UF 16V
CN81 CJP17GB113ZY WAFER
D801 CVD50BOBBWGA L.E.D , 2 COLOR (ORG , BLUE) TOL-50BOBBWGA
D802 CVD1N4003ST DIODE , RECT 1N4003
FIP1 HFLHCA-17SM03T FIP
JW83 CWE8102080RV WIRE(1P)
JW84 CWE8102080RV WIRE(1P)
Q209 HVTKRA107MT T.R KRA107M
Q210 HVTKRC107MT T.R KRC107M
R801 CRD20TJ102T RES , CARBON 1K OHM 1/5W J
R802 CRD20TJ102T RES , CARBON 1K OHM 1/5W J
R803 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J
R804 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J
R805 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J
R806 CRD20TJ182T RES , CARBON 1.8K OHM 1/5W J
R807 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J
R808 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J
R809 CRD20TJ332T RES , CARBON 3.3K OHM 1/5W J
R812 CRD20TJ271T RES , CARBON 270 OHM 1/5W J
R813 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J
R814 CRD20TJ272T RES , CARBON 2.7K OHM 1/5W J
R815 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J
R816 CRD20TJ822T RES , CARBON 8.2K OHM 1/5W J
R817 CRD20TJ330T RES , CARBON 33 OHM 1/5W J
R818 CRD20TJ330T RES , CARBON 33 OHM 1/5W J
R819 CRD20TJ102T RES , CARBON 1K OHM 1/5W J
R820 CRD20TJ330T RES , CARBON 33 OHM 1/5W J
R821 CRD25TJ272T RES , CARBON 2.7K OHM 1/4W J
R822 CRD20TJ271T RES , CARBON 270 OHM 1/5W J
RC81 CRVKSM603TH2E SENSOR , REMOCON KSM603TH2E
S801 CST1A012ZT SW , TACT SKHV10910G
S802 CST1A012ZT SW , TACT SKHV10910G
S803 CST1A012ZT SW , TACT SKHV10910G
S804 CST1A012ZT SW , TACT SKHV10910G
S805 CST1A012ZT SW , TACT SKHV10910G
S806 CST1A012ZT SW , TACT SKHV10910G
S807 CST1A012ZT SW , TACT SKHV10910G
S808 CST1A012ZT SW , TACT SKHV10910G
S809 CST1A012ZT SW , TACT SKHV10910G
S810 CST1A012ZT SW , TACT SKHV10910G
S811 CST1A012ZT SW , TACT SKHV10910G
VR81 CSR2A036Z ENCODER VR

3-8
 REF NO. PART NO. DESCRIPTION REMARKS
CUP12018-4 SPEAKER BOARD
BN31 CWB2B005050EN WIRE ASS'Y
BN62 CWB1C005200BM WIRE ASS'Y(5P, 200MM)
C303 HCQI1H682JZT CAP , MYLAR 6800PF 50V J
C304 HCQI1H682JZT CAP , MYLAR 6800PF 50V J
C305 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
C306 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z
CN53 CJP05GA01ZY WAFER(YMW025-05R)
R305 CRG1ANJ391H RES , METAL OXIDE FILM 390 OHM 1W J
R306 CRG1ANJ391H RES , METAL OXIDE FILM 390 OHM 1W J
R307 CRD20TJ473T RES , CARBON 47K OHM 1/5W J
R308 CRD20TJ473T RES , CARBON 47K OHM 1/5W J
RY72 HSL4A004ZU RELAY OSA-SS-212DM3
SP31 CJJ5P012Z TERMINAL , SPEAKER

REF NO. PART NO. DESCRIPTION REMARKS

CUP12018-5 POWER BOARD
AT21 CJJ3G012Z TERMINAL , ANT DAB RF - 055A C715DABC ONLY
BK21 CMD1A387 BRACKET , PCB
BK22 CMD1A387 BRACKET , PCB
BN23 CJP44TT153ZY PIN , HEADER DAB(2.00MM) DAB2025 C715DABC ONLY
BN25 CWB2B005250EN WIRE ASS'Y
BN26 CJP02TT155ZY PIN , HEADER (2.54MM) DAB2025 C715DABC ONLY
BN53 CWB1C005100BM WIRE ASS'Y(5P, 100MM)
BN94 CWB1C011150BM WIRE ASS'Y(11P, 150MM)
C201 CCME2A104JXT CAP , METALLIZED FILM HMFS104J2AP050T
C202 HCQI1H103JZT CAP , MYLAR 0.01UF 50V J
C203 HCQI1H103JZT CAP , MYLAR 0.01UF 50V J
C204 CCET1HKLH332KK8 CAP , ELECT 3300UF 50V
C205 CCET1HKLH332KK8 CAP , ELECT 3300UF 50V
C206 HCQI1H103JZT CAP , MYLAR 0.01UF 50V J
C207 HCQI1H103JZT CAP , MYLAR 0.01UF 50V J
C208 CCEA1HH4R7T CAP , ELECT 4.7UF 50V C715DABC ONLY
C209 CCEA1HH4R7T CAP , ELECT 4.7UF 50V C715DABC ONLY
C210 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z C715DABC ONLY
C211 CCEA1CH470T CAP , ELECT 47UF 16V C715DABC ONLY
C212 CCEA1CH470T CAP , ELECT 47UF 16V C715DABC ONLY
C213 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z C715DABC ONLY
C214 CCEA1AH471T CAP , ELECT 470UF 10V C715DABC ONLY
C215 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z C715DABC ONLY
C216 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z C715DABC ONLY
C217 CCEA1CH101T CAP , ELECT 100UF 16V C715DABC ONLY
C219 CCEA1AH471T CAP , ELECT 470UF 10V C715DABC ONLY
C220 CCEA1CH101T CAP , ELECT 100UF 16V
C221 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z
C223 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C224 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C225 CCEA1CH102E CAP , ELECT 1000UF 16V
C226 CCEA1CH102E CAP , ELECT 1000UF 16V
C227 CCEA1EH222E CAP , ELECT 2200UF 25V
C228 CCEA1EH222E CAP , ELECT 2200UF 25V
C229 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C230 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C232 CCFT1H223ZF CAP , CERAMIC 0.022UF 50V Z
C233 CCEA1EH331T CAP , ELECT 33OUF 25V
C234 CCEA1CH101T CAP , ELECT 100UF 16V
C235 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C236 CCEA1EH471E CAP , ELECT 470UF/25V
C237 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C238 KCKDKS472ME CAP , CERAMIC(X1/Y2/SC) 0.0047UF/2.5KV
C241 CCEA1EH102E CAP , ELECT 1000UF 25V C715DABC ONLY
C241 CCEA1EH331T CAP , ELECT 330UF 25V C715C, C715AH
C243 CCFT1H103ZF CAP , CERAMIC 0.01UF 50V Z
C245 CCFT1H103ZF CAP , CERAMIC 0.01UF 50V Z C715DABC ONLY
C246 CCEA1EH102E CAP , ELECT 1000UF 25V
C247 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
CN24 CJP08GA01ZY WAFER, STRAIGHT, 8PIN
CN91 CJP02KA060ZY WAFER
CN92 CJP02GA89ZY WAFER
CN93 CJP03GA90ZY WAFER
D201 HVDPBU604F DIODE , BRIDGE US PBU604F
D202 CVD1N4003ST DIODE , RECT 1N4003
D203 CVD1N4003ST DIODE , RECT 1N4003
D204 CVD1N4003ST DIODE , RECT 1N4003
D205 CVD1N4003ST DIODE , RECT 1N4003
D207 CVD1SS133MT DIODE 1SS133
D208 HVDMTZJ6.2BT DIODE , ZENER 6.2V
D209 CVD1SS133MT DIODE 1SS133
D210 CVD1N4003SRT DIODE , RECT 1N4003
D211 CVD1N4003SRT DIODE , RECT 1N4003
D212 CVD1N4003SRT DIODE , RECT 1N4003

3-9
D213 CVD1N4003SRT DIODE , RECT 1N4003
D214 CVD1N4003ST DIODE , RECT 1N4003
D215 CVD1N4003ST DIODE , RECT 1N4003
D216 CVD1N4003ST DIODE , RECT 1N4003
D217 CVD1N4003ST DIODE , RECT 1N4003
ET91 CNE75 PLATE , EARTH
F751 KBA2C2000TLEZ FUSE T 2A L 250V C715DABC, C715C
F751 KBA2C3000TLUZ FUSE SB 3A 250V C715AH ONLY
IC21 HVI74HC4066D I.C , SWITCHING 74HC4066D C715DABC ONLY
IC91 CVIKIA7812A I.C , REGULATOR + 12V
IC92 CVIKIA7912A I.C , REGULATOR - 12V
IC93 CVIKIA7805A I.C , REGULATOR + 5V C715DABC ONLY
IC93 HVIKA78L05AZT I.C , REGULATOR + 5V C715C, C715AH
IC94 CVIKIA7805A I.C , REGULATOR + 5V C715DABC ONLY
IC95 HVILM1117S-ADJ I.C , REGULATOR LM1117-ADJ C715DABC ONLY
JK21 HJSTOTX177L MODULE , OPTICAL(TX) TOTX177L
Q201 HVTKRC107MT T.R KRC107M C715DABC ONLY
Q207 HVTKRC107MT T.R KRC107M
Q208 HVTKSC2316YT T.R KSC2316Y
R201 CRD25TJ183T RES , CARBON 18K OHM 1/4W J
R202 CRD25TJ183T RES , CARBON 18K OHM 1/4W J
R203 CRD20TJ473T RES , CARBON 47K OHM 1/5W J C715DABC ONLY
R204 CRD20TJ473T RES , CARBON 47K OHM 1/5W J C715DABC ONLY
R205 CRD20TJ391T RES , CARBON 20K OHM 1/5W J C715DABC ONLY
R206 CRD20TJ221T RES , CARBON 220 OHM 1/5W J C715DABC ONLY
R207 CRD20TJ103T RES , CARBON 10K OHM 1/5W J C715DABC ONLY
R208 CRD20TJ1R0T RES , CARBON 1 OHM 1/5W J C715DABC ONLY
R209 CRD20TJ102T RES , CARBON 1K OHM 1/5W J C715DABC ONLY
R210 CRD20TJ152T RES , CARBON 1.5K OHM 1/5W J C715DABC ONLY
R211 CRD20TJ472T RES , CARBON 4.7K OHM 1/5W J C715DABC ONLY
R213 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J C715DABC ONLY
R214 CRD20TJ562T RES , CARBON 5.6K OHM 1/5W J C715DABC ONLY
R216 HRDERC12UGK335T RES , CARBON ERC12UGK 3.3M OHM
R218 CRD20TJ122T RES , CARBON 1.2K OHM 1/5W J
R219 CRQ1AJR47H RES , FUSE
R220 CRQ1AJR47H RES , FUSE
R221 CRD25TJ183T RES , CARBON
R222 CRD25TJ183T RES , CARBON
R223 CRQ1AJR47H RES , FUSE
R224 CRQ1AJR47H RES , FUSE
RY71 HSL1D016ZE RELAY SDT-S-109DMR
T701 CLT5I002ZE TRANS , SUB
T701 CLT5I002ZU TRANS , SUB
WF21 CJP13GA117ZY WAFER , CARD CABLE

REF NO. PART NO. DESCRIPTION REMARKS

CUP12018-6 AMP BOARD
BK23 CMD1A387 BRACKET , PCB
BK24 CMD1A387 BRACKET , PCB
BN61 CWB2B003180EN WIRE ASS'Y(3P, 180MM)
C603 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C604 CCEA1HH4R7T CAP , ELECT 4.7UF 50V
C607 CCEA1HH101T CAP , ELECT 100UF 50V
C608 CCEA1HH101T CAP , ELECT 100UF 50V
C621 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C622 CCEA1HH470T CAP , ELECT 47UF 50V
C623 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C624 CCEA1HH470T CAP , ELECT 47UF 50V
C625 CCFT1H104ZF CAP , SEMICONDUCTOR 0.1UF 50V Z
C627 HCQI1H682JZT CAP , MYLAR 6800PF 50V J
C628 HCQI1H682JZT CAP , MYLAR 6800PF 50V J
C631 CCME2A104JXT CAP , METALLIZED FILM HMFS104J2AP050T
C632 CCME2A104JXT CAP , METALLIZED FILM HMFS104J2AP050T
CN25 CJP05GA19ZY WAFER , STRAIGHT
CN62 CJP05GA01ZY WAFER(YMW025-05R)
IC61 CVITDA7292 I.C , AMP 40WX2CH
L601 KLZ9H001Z BEAD , CORE
L602 KLZ9H001Z BEAD , CORE
R603 CRD25TJ183T RES , CARBON 18K OHM 1/4W J
R604 CRD20TJ183T RES , CARBON 18K OHM 1/5W J
R605 CRD25TJ102T RES , CARBON 1K OHM 1/4W J
R606 CRD20TJ102T RES , CARBON 1K OHM 1/5W J
R607 CRD25TJ822T RES , CARBON 8.2K OHM 1/5W J
R608 CRD25TJ822T RES , CARBON 8.2K OHM 1/5W J
R621 CRD20TJ104T RES , CARBON 100K OHM 1/5W J
R631 KRG1SANJ4R7RT RES, METAL(OXIDE)FILM,5% 4.7/1W(RADIAL)
R632 KRG1SANJ4R7RT RES, METAL(OXIDE)FILM,5% 4.7/1W(RADIAL)

3-10
 Service Hint
Product: C715
Hardware Technical Bulletin: C715-H2009-01
Date: APRIL 1 2009 Subject: TRAY FUNCTIONALITY

Note: This condition only affects a small number of units produced with
this batch of leaf switches

DESCRIPTION: CD tray may not open or close.

REASON: The tray sense switch can grow tiny conductive "whiskers"
across it's contact pads shorting the switch and preventing the tray from
opening/closing.

SOLUTION: Change the value of R101 and R731102 from 18K to 470
ohm to increase the current flow across each contact switch pads eliminating the
“WHISKERS”. Resistor 470R 1/8w SMD 0805.
 3%26)#% -!.5!,
©
#  # $!"

.!$ %,%#42/.)#3 ).4%2.!4)/.!,

4/2/.4/