DATA SHEET

Form 1684-240409
PAGE 1

SNAP PAC RACKS

Features
> Compatible with all SNAP PAC brains and R-series controllers
> Secure mounting for SNAP I/O modules plus a SNAP brain or
on-the-rack SNAP PAC controller
> Analog, digital, and serial modules on the same rack
> Panel or DIN-rail mounting
> Modules snap into place

SNAP-PAC-RCK12

DESCRIPTION
SNAP PAC I/O mounting racks are designed to hold an intelligent
SNAP I/O processor—a SNAP PAC brain or a SNAP PAC R-series SNAP PAC racks require a 5 VDC power source. One power supply can
on-the-rack controller—and several I/O modules. usually power the rack, the I/O processor (controller or brain), and all
modules on the rack. See form 1120, the SNAP Power Supplies Data
Since SNAP analog, digital, and serial I/O modules all have the same Sheet, to choose a power supply.
footprint, customers using SNAP PAC racks can mix all these modules
on the same I/O mounting rack. Field devices are wired directly to the
top-mounted connectors on the modules plugged into each rack, or
through breakout boards when additional wiring space is required.
(See form 1756, the SNAP TEX Cables and Breakout Boards Data Sheet,
for more information.)
SNAP PAC racks can accommodate up to 4, 8, 12, or 16 I/O modules.
The module and rack design allows modules to simply “snap” on the
mounting rack.

Part Numbers
SNAP-PAC-RCK8 (8-Module Position I/O Mounting Rack) Part Description
Shown with SNAP-PAC-R1 controller and SNAP modules (all SNAP-PAC-RCK4 4-module SNAP PAC rack
purchased separately)
SNAP-PAC-RCK8 8-module SNAP PAC rack
SNAP PAC racks use a retention rail locking system. Install two 4-40 by SNAP-PAC-RCK12 12-module SNAP PAC rack
½-inch standard machine screws to hold each module in position.
SNAP-PAC-RCK16 16-module SNAP PAC rack
All SNAP PAC racks offer panel mounting and the option of DIN-rail SNAP-FUSE7.5AB 7.5-amp fuse, 25 pack
mounting. DIN-rail adapter part numbers are shown in the table
SNAP-TEX-DRC10 SNAP rack DIN-rail adapter clip, 10-pack
below. For more information, see form 1772, the SNAP TEX
Mounting/Wiring Tools and Spare Parts Data Sheet. Wide end cap for SNAP PAC racks DIN-rail
SNAP-TEX-REC10W
assemblies, 10-pack

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [email protected]

© 2007-2024 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
 DATA SHEET
Form 1684-240409

PAGE 2

SPECIFICATIONS

Power1 Requirements 5.0 to 5.2 VDC @ 4.2 Amps max

SNAP-PAC-R1 SNAP-PAC-R2-W3
SNAP-PAC-R2 SNAP-PAC-EB1-W3
3
SNAP-PAC-EB1 SNAP-PAC-EB2-W3
I/O Processor2 3
SNAP-PAC-EB2 SNAP-PAC-R1-FM3
Compatibility
SNAP-PAC-SB1 SNAP-PAC-R2-FM3
SNAP-PAC-SB2
SNAP-PAC-EB1-FM3
SNAP-PAC-R1-W3
SNAP-PAC-EB2-FM3
Replacement Fuse SNAP-FUSE7.5AB or Littelfuse 297 07.5
Rack Power Terminals
22 to 14 AWG
Wire Size
Operating Temperature –20 to 70 °C
Module Mating Connector Pinout (female)
Storage Temperature –40 to 85 °C
Relative Humidity 95%, non-condensing
Non -FM models: UL, CE, RoHS, DFARS; UKCA
Agency Approvals
-FM models: CE, ATEX, RoHS, DFARS; UKCA
Warranty 30 months from date of manufacture
1 Power requirements shown are for a rack, a processor, and a full load of analog
modules. Power requirements for SNAP serial and high-density modules are
higher. See module data sheets.
2 “I/O Processor” means a SNAP PAC brain or SNAP PAC on-the-rack controller.
For compatibility with legacy Opto 22 products, see form #1693, Legacy and Cur-
rent Product Comparison and Compatibility Charts.
3 Obsolete product; will be unavailable when current stock is depleted.

Power Schematic

Notes on Grounding WARNING: EXPLOSION HAZARD. DO NOT DISCONNECT WHILE

Pin 18 E GND on each module (see diagram above right) is connected CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE NON-HAZARDOUS.
to the rack’s GND. Module hold-down screws are also connected to
the rack’s GND. AVERTISSEMENT: RISQUE D'EXPLOSION. NE PAS DÉBRANCHER
The brain or rack-mounted controller is connected to the rack’s GND TANT QUE LE CIRCUIT EST SOUS TENSION, À MOINS QU'IL NE
through its center hold-down screw. S'AGISSE D'UN EMPLACEMENT NON DANGEREUX.

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [email protected]

© 2007-2024 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
 DATA SHEET
Form 1684-240409

PAGE 3

DIMENSIONAL DRAWINGS

Overall Dimensions

SNAP PAC R-series controller or SNAP module

brain (purchased separately) (purchased
separately)

4.45***
(112.01 mm)

See table for overall length

dimensions for specific model

Overall Length Dimensions

Width Width Length Length
Part Number Description
(inches) (mm) (inches) (mm)
SNAP-PAC-RCK4 4-module rack 4.45 112.01 6.25 158.75
SNAP-PAC-RCK8 8-module rack 4.45 112.01 9.25 234.95
SNAP-PAC-RCK12 12-module rack 4.45 112.01 12.25 311.15
SNAP-PAC-RCK16 16-module rack 4.45 112.01 15.25 387.35

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [email protected]

© 2007-2024 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
 DATA SHEET
Form 1684-240409

PAGE 4

DIMENSIONAL DRAWINGS (CONTINUED)

Right Side View with DIN-Rail Option Installed

(See form 1772)

For more information on DIN-rail mounting kits, see form 1772,

the SNAP TEX Mounting/Wiring Tools and Spare Parts Data Sheet.

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [email protected]

© 2007-2024 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
 DATA SHEET
Form 1684-240409

PAGE 5

MOUNTING THE EXTRUSION ONTO A PANEL

Use the following steps to mount a rack onto a panel. For DIN-rail Alternate Method: Prefabrication of Panels
mounting, see page 6.
(No product on site)
CAUTION: Do not let cutting fluids, cleaners, lubricants, or other
Mounting holes are in sets of two, located on lower left and upper
chemicals contact the plastic extrusion, as they can cause cracking. If you
right with respect to a center line (CL).
use these chemicals before rack installation, be sure they are thoroughly
1. Using the diagram below, determine CL1 mounting hole
cleaned off.
positions. (CL1 is located on the left side of all SNAP PAC rack
mounting extrusions.)
Preferred Method: Template 2. Use the center-to-center length specification table below to
(Product on site) determine the offset between center lines and the number of
1. Use SNAP PAC rack mounting extrusion as template. center line positions for each model.
2. Use the diagram below to determine required product and option 3. Repeat the process for each center line position.
clearances.

Typical Plain View of SNAP Mounting Extrusion

Center-to-Center Length (All Models)

Center-to-Center Number of Center
Part Number Description
Length Positions
SNAP-PAC-RCK4 4-module rack 4.02 in. 2
SNAP-PAC-RCK8 8-module rack 3.51 in. 3
SNAP-PAC-RCK12 12-module rack 5.01 in. 3
SNAP-PAC-RCK16 16-module rack 4.34 in. 4

OPTO 22 • 800-321-6786 • 1-951-695-3000 • www.opto22.com • [email protected]

© 2007-2024 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
 DATA SHEET
Form 1684-240409

PAGE 6

ASSEMBLING AND MOUNTING ON A DIN RAIL

For panel mounting, see page 5.

1. (This step only for racks with three or more clips.)

Slide one DIN clip to the middle position and
secure with the rivet provided. For racks with four Rivet
clips, add an additional middle clip. (included)

2. Insert one edge of the circuit board into the

extrusion.
3 2
3. Push down hard on the other edge to snap the 4
board into place.

4. Attach one DIN clip to each end cap using the

slots in the end caps as shown.

5. Using the screws provided, secure an end cap and

DIN clip assembly to each end of the extrusion.

5
Removing the Circuit Board from the Rack
Extrusion
If end caps are present, remove them. Then insert a flathead
screwdriver in one of the circuit board release notches and pry
up the board. Repeat in the other release notches until the
board pops out of the extrusion.

Attaching the Adapter Clip to a DIN Rail Extrusion

1. Hook the DIN-rail clip over the top of the DIN rail. assembly
2. Using a screwdriver, pry open the DIN-rail clip flange at
the bottom of the clip. Push the clip toward the DIN rail. DIN rail
3. Snap the DIN-rail clip into place

OPTO 22 • www.opto22.com SALES • [email protected] SUPPORT • [email protected]

43044 Business Park Dr. Temecula, CA 92590-3614 800-321-6786 • 1-951-695-3000 800-835-6786 • 1-951-695-3080

© 2007-2024 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
More about Opto 22
PRODUCTS groov EPIC Software

Opto 22 develops and manufactures reliable, easy-to-use, open The groov EPIC processor comes ready to run the software you need:
standards-based hardware and software • Programming: Choose flowchart-based
products. Industrial automation, process PAC Control, CODESYS Development
control, remote monitoring, data acquisition, System for IEC61131-3 compliant
and industrial internet of things (IIoT) programs, or secure shell access (SSH) to
applications worldwide all rely on Opto 22. the Linux OS for custom applications
• Node-RED for creating simple IIoT logic
groov RIO® flows from pre-built nodes
groov RIO edge I/O offers a single, compact, • Efficient MQTT data communications
PoE-powered industrial package with web- with string or Sparkplug data formats
based configuration and IIoT software built • Multiple OPC UA server options
in, support for multiple OT and IT protocols, • HMI: groov View to build your own HMI
and security features like a device firewall, viewable on touchscreen, PCs, and
data encryption, and user account control. mobile devices; PAC Display for a
Standing alone, groov RIO connects to sensors, equipment, and legacy Windows HMI; Node-RED dashboard UI
systems, collecting and securely publishing data from field to cloud. • Ignition or Ignition Edge® from Inductive Automation (requires
Choose a universal I/O model with thousands of possible field I/O license purchase) with OPC-UA drivers to Allen-Bradley®,
configurations, with or without Ignition from Inductive Automation®, Siemens®, and other control systems, and MQTT communications
or a RIO EMU energy monitoring unit that reports 64 energy data
values from 3-phase loads up to 600 VAC, Delta or Wye. Older products
You can even write an IEC 61131-3 compliant control program to run From solid state relays, to world-famous G4 and SNAP I/O, to SNAP
on groov RIO, using CODESYS. You can also use groov RIO with a PAC controllers, older Opto 22 products are still supported and
Modbus/TCP master or as remote I/O for a groov EPIC system. working hard at thousands of installations worldwide. You can count
on us for the reliability and service you expect, now and in the future.
groov EPIC® System
Opto 22’s groov Edge Programmable Industrial Controller (EPIC) QUALITY
system gives you industrially hardened control with a flexible Linux®- Founded in 1974, Opto 22 has established a worldwide reputation for
based processor with gateway functions, guaranteed-for-life I/O, and high-quality products. All are made in the U.S.A. at our manufacturing
software for your automation and IIoT applications. facility in Temecula, California.
groov EPIC Processor Because we test each product twice before it leaves our factory rather
than testing a sample of each batch, we can afford to guarantee most
The heart of the system is the groov EPIC processor. It handles a wide
solid-state relays and optically isolated I/O modules for life.
range of digital, analog, and serial functions for data collection,
remote monitoring, process control, and discrete and hybrid
manufacturing. FREE PRODUCT SUPPORT
In addition, the EPIC provides secure data communications among Opto 22’s California-based Product Support Group offers free
physical assets, control systems, software applications, and online technical support for Opto 22 products from engineers with decades
services, both on premises and in the cloud. No industrial PC needed. of training and experience. Support is available in English and Spanish
by phone or email, Monday–Friday, 7 a.m. to 5 p.m. PST.
Configuring and troubleshooting I/O and networking is easier with
the EPIC’s integrated high-resolution color touchscreen. Authorized Support is always available on our website, including free online
users can manage the system locally on the touchscreen, on a training at OptoU, how-to videos, user’s guides, the Opto 22
monitor connected via the HDMI or USB ports, or on a PC or mobile KnowledgeBase, and OptoForums.
device with a web browser.

groov EPIC I/O PURCHASING OPTO 22 PRODUCTS

groov I/O connects locally to sensors and equipment. Modules have a Opto 22 products are sold directly and through a worldwide network
spring-clamp terminal strip, integrated wireway, swing-away cover, of distributors, partners, and system integrators. For more information,
and LEDs indicating module health and discrete channel status. groov contact Opto 22 headquarters at 800-321-6786 (toll-free in the U.S.
I/O is hot swappable, UL Hazardous Locations approved, and ATEX and Canada) or +1-951-695-3000, or visit our website at
compliant. www.opto22.com.

OPTO 22 • www.opto22.com SALES • [email protected] SUPPORT • [email protected]

43044 Business Park Dr. Temecula, CA 92590-3614 800-321-6786 • 1-951-695-3000 800-835-6786 • 1-951-695-3080

© 2001–2023 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
Form 1335-230802