Scribd
Upload
19 views2 pages

Injector Trim File

The document outlines the procedure for loading injector trim files into the Electronic Control Module (ECM) for C6.6 Industrial Engines. It specifies conditions under which the trim files must be loaded, such as replacing an electronic unit injector or ECM, and provides detailed steps for exchanging injectors and downloading the necessary files. The document serves as a guide for technicians to ensure proper calibration and functionality of the engine's injectors.

Uploaded by

tho thongan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
19 views2 pages

Injector Trim File

The document outlines the procedure for loading injector trim files into the Electronic Control Module (ECM) for C6.6 Industrial Engines. It specifies conditions under which the trim files must be loaded, such as replacing an electronic unit injector or ECM, and provides detailed steps for exchanging injectors and downloading the necessary files. The document serves as a guide for technicians to ensure proper calibration and functionality of the engine's injectors.

Uploaded by

tho thongan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

C6.

6 Industrial Engine 66600001-UP(SEBP4314 - 28) - Document Structure Page 1 of 2

Injector Trim File


SMCS - 1290

The electronic service tool is used to load the injector trim files into the Electronic Control Module
(ECM).

The injector trim files must be loaded into the ECM if any of the following conditions occur:

z An electronic unit injector is replaced.

z The ECM is replaced.

z Diagnostic code 0268-02 is active.

z Electronic unit injectors are exchanged between cylinders.

Exchanging Electronic Unit Injectors

Exchanging electronic unit injectors can help determine if a combustion problem is in the electronic
unit injector or in the cylinder. If two electronic unit injectors that are currently installed in the
engine are exchanged between cylinders, the injector trim files can also be exchanged. Press the
"Exchange" button at the bottom of the "Injector Trim Calibration" screen on the electronic service
tool. Select the two electronic unit injectors that will be exchanged and press the "OK" button. The
tattletale for the electronic unit injectors that were exchanged will increase by one.

Note: The serial number for the electronic unit injector and the confirmation code number for
the electronic unit injector are located on the electronic unit injector.

1. Record the serial number and the confirmation code numberfor each electronic unit injector.

2. Obtain the injector trim file by one of the following methods:

{ Select "Service Software Files" on SIS.

{ Use the compact disc that is included with a replacement electronic unit injector.

3. Enter the serial number for the electronic unit injector in the search field.

4. Download the injector trim file to the PC. Repeat this procedure for each electronic unit
injector, as required.

5. Connect the electronic service tool to the diagnostic connector. Refer to Troubleshooting,
"Electronic Service Tools".

6. Turn the keyswitch to the ON position.

7. Select the following menu options on the electronic service tool:

{ Service

{ Calibrations

https://10.1.2.37:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/siswe... 7/24/2009
C6.6 Industrial Engine 66600001-UP(SEBP4314 - 28) - Document Structure Page 2 of 2

{ Injector Trim Calibration

8. Select the appropriate cylinder.

9. Click on the "Change" button.

10. Select the appropriate injector trim file from the PC.

11. Click on the "Open" button.

12. If you are prompted by the electronic service tool, enter the confirmation code number for the
electronic unit injector into the field.

13. Click on the "OK" button.

The injector trim file is loaded into the ECM.

14. Repeat the procedure for each cylinder, as required.

https://10.1.2.37:8443/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/siswe... 7/24/2009

You might also like