Tuya Keypad Access Control

User Manual
1. Description

The device is a standalone access control and proximity card reader which supports EM & MF card types. It
builds-in STC microprocessor, with strong anti-interference ability,high security and reliability,powerful function
and convenient operation. It’s widely used in high-end buildings, residential communities and other public
places.

2. Features

Ultra-low Power Standby current is less than 30mA

Wiegand Interface WG26 or WG34 input and output
Searching time Less than 0.1s after reading card
Backlight keypad Operate easily at night
Doorbell interface Support external wired doorbell
Access ways Card, Pin code, Card & Pin code
Independent codes Use codes without related card
Change codes Users can change codes by themselves
Delete users by card No. The lost card can be delete by keyboard

3. Specifications

Working Voltage：DC12-24V Standby Current：≤30mA

Card Reading Distance：1～3cm Capacity：2000 users
Working Temperature：-40℃～60℃ Working Humidity：10%～90%
Lock output load：≤3A Door Relay time：0～99S （Adjustable）

4. Installation

Drill hole according to the size of the device and fix the back shell with the equipped screw.Thread the cable
through the cable hole. connect the wires according to your required function, and wrap the unused wires to
avoid short circuit. After connecting the wire, install the machine. (as show below)
5. Wiring

Color ID Description
Green D0 Wiegand Input(Wiegand Output in Card Reader Mode)
White D1 Wiegand Input(Wiegand Output in Card Reader Mode)
Yellow OPEN Exit Button input terminal
Red +12V 12V + DC Regulated Power Input
Black GND 12V - DC Regulated Power Input
Blue NO Relay normally-on terminal
Purple COM Relay Public terminal
Orange NC Relay normally-off terminal
Pink BELL_A Doorbell button one terminal
Pink BELL_B Doorbell button to the other terminal

6.1 Diagram

Common Power Supply

6.2 Special Power Supply

6.3 Reader Mode

7. Sound & Light indication

Operate Status LED Light Color Buzzer

Standby Red
Keypad Beep
Operation Successful Green Beep－

Operation Failed Beep-Beep-Beep

Entering into Programming Flash Red Slowly Beep－

Programmable Status Orange

Exit Programming Red Beep－
Door Opening Green Beep－
 8. Advance setting
Add Users Notes
Change Master code * Master code # 0 New code # New code Default factory master code is 999999.

Add card * Master code # 1 Read card # ... # Cards can be added continuously

Add card number * Master code # 1 8 digits or 10 digits # Card number can be added continuously
1
Add ID number+card * Master code # 1 ID number # Read Add user with specify ID number, easily find and delete.

card #

Add ID number+card * Master code # 1 ID number # 8 digits Add user with specify ID number, easily find and delete.

number or 10 digits #

Add PIN code * Master code # 1 ID number # 4 digits ID number is from 1-1000

Pin code #

Delete Users
Delete card * Master code # 2 Read card or 8 digits or 10 Cards can be deleted continuously

digits #
2
Delete ID number * Master code # 2 ID number # When the card is broken or lost, you can delete the user by ID

number

Delete ALL users * Master code # 2 0000 # Delete ALL PIN code & card users except public PIN code.

Access ways
By card * Master code # 30 # Only the card user could unlock the door, keypad is invalid
3
By card+PIN code * Master code # 31 # To enable this function, the user PIN code has to be changed.

By card or PIN code * Master code # 32 # Both card user and PIN user could unlock the door (factory default)
 Relay Output Delay Time
4 Door relay strike time * Master code # 4 0～99 # Door opening time range: 0-99s
Default 5s

Standalone access * Master code # 50 # The door will be locked automatically after open the
control mode door normally
Relay toggle mode * Master code # 51 # The door will not be locked automatically.To lock the
5
door, the user has to read the card or press the exit
button.

Reader mode * Master code # 52 26/34 # WG26/34 input and output

6 Bind a code to a * Master code # 6 Read card 4 digits When using card+code to unlock the door
specific card code #

7 Data backup output * Master code # 70 # Send the data to external device.
Data backup input * Master code # 71 # The device will receive the data.
Wifi matching * Master code # 73 # WiFi match（optional）

Add public code * Master code # 9 4 digits code # Only one public code is available.
9
Delete public code: * Master code # 9 #
Change the code by * Read card New code # Repeat new Code #
user card
*
Change the code by ID * Old code # New code # Repeat New code #
number added Note: All of codes will be modified except public code.

Reset to Factory Power off, press the exit button continuously, power on, hearing beep sound twice, meanwhile, the indicator light
Default turns orange, swipe the first card as for master add card, swipe the second card as for the master delete card,
the master code has been reset to 999999, factory default settings are successful.
★Registered user data won’t be deleted when reset to factory default

9 Master Card Operation

9.1 Add Card
Read master add card , Read the 1st user card Read the 2nd user card …,Read master add card
Note: The master add card is used to add card users continuously and quickly. When you read the master add card at the first time, you
will hear short "BEEP" sound twice and the indicator light turns orange, it means you have entered into add user programming. When you
read the master add card at the second time, you will hear long "BEEP" sound once and the indicator light turns red, it means you have
exited the add user programming.

9.2 Delete Card

Read master delete card , Read the 1st user card Read the 2nd user card … , Read master delete card
Note: The master delete card is used to delete card users continuously and quickly. When you read the master delete card at the first
time, you will hear short "BEEP" sound twice and the indicator light turns orange, it means you have entered into delete user
programming. When you read the master delete card at the second time, you will hear long "BEEP" sound once, the indicator light turns
red, it means you have exited the delete user programming.

10 Data Backup Operation

Example: Backup the data of machine A to machine B
The green wire and white wire of machine A connects with the green wire and white wire of machine B correspondingly, set B for
receiving mode at first, then set A for sending mode, the indicator light turns green flash during the data backup, data backup is
successful when indicator light turns red.