DMV 347 HFG is an austenitic stainless steel tube designed for use as superheater and reheater boiler tubes in coal-fired power plants with steam temperatures up to 600°C. It has excellent high-temperature corrosion resistance and creep resistance from 580-640°C. DMV 347 HFG tubes are produced seamlessly in sizes up to an outer diameter of 65mm and wall thickness of 12.5mm. The steel has fine-grained microstructure and composition that provide strong mechanical properties at high temperatures.
DMV 347 HFG is an austenitic stainless steel tube designed for use as superheater and reheater boiler tubes in coal-fired power plants with steam temperatures up to 600°C. It has excellent high-temperature corrosion resistance and creep resistance from 580-640°C. DMV 347 HFG tubes are produced seamlessly in sizes up to an outer diameter of 65mm and wall thickness of 12.5mm. The steel has fine-grained microstructure and composition that provide strong mechanical properties at high temperatures.
DMV 347 HFG is an austenitic stainless steel tube designed for use as superheater and reheater boiler tubes in coal-fired power plants with steam temperatures up to 600°C. It has excellent high-temperature corrosion resistance and creep resistance from 580-640°C. DMV 347 HFG tubes are produced seamlessly in sizes up to an outer diameter of 65mm and wall thickness of 12.5mm. The steel has fine-grained microstructure and composition that provide strong mechanical properties at high temperatures.
DMV 347 HFG is an austenitic stainless steel tube designed for use as superheater and reheater boiler tubes in coal-fired power plants with steam temperatures up to 600°C. It has excellent high-temperature corrosion resistance and creep resistance from 580-640°C. DMV 347 HFG tubes are produced seamlessly in sizes up to an outer diameter of 65mm and wall thickness of 12.5mm. The steel has fine-grained microstructure and composition that provide strong mechanical properties at high temperatures.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 4
D A T A S H E E T
DMV 347 HFG
1 Application DMV 347 HFG has been designed for application as superheater and reheater boiler tube grade. 347 HFG has proved to be suitable in most advanced coal fired power stations using steam temperatures of up to approximately 600C (1112F) in supercritical and ultra supercritical vessel designs.
3.2 Available Sizes
DMV 347 HFG is produced as seamless austenitic tube, suitable for all recently used austenitic reheater and superheater boiler tube sizes. Following VdTV Material Data Sheet 547, 06.2003, the max. outer diameter is 65 mm and the max. wall thickness is 12.5 mm. Other sizes are available upon request.
3.4 Mechanical Properties
3.4.1 At Solution Annealed Condition According ASME SA-213/SA-213M MPa Y.S. min. U.T.S. min. E in 2, min., % 2
ksi 30 80 35
(205) (550)
2 Main Features 3.3 Chemical Composition Austenitic stainless steel with a fine grain structure of No. 7 10 according to ASTM E112 after a thermomechanical treatment of softening, cold finishing and solution annealing Very good high temperature corrosion resistance Very good creep resistance at high temperatures, specially in the range of 580C (1076F) to 640C (1184F) Mass % according ASME SA-213/SA213M % min. C Si Mn P S Cr Ni 17.00 9.00 8xC 0.06 % max. 0.10 0.75 2.00 0.040 0.030 20.00 13.00 1.0
Following VdTV Material Data Sheet 547, 06.2003 MPa 0.2% Y.S. min. 1.0% Y.S. min. U.T.S. A% ( ) = calculated values
ksi (29.7) (34.8) (78.8 108.8) 35
205 240 550 - 750
3 Description 3.1 Specifications 1.4908, X8CrNi 19 11, European Steel registration TP347HFG according ASME SA213/SA-213M, Specification for seamless ferritic and austenitic alloy-steel boiler, superheater, and heat-exchanger tubes, United States Following VdTV Material Data Sheet 547, 06.2003, Federal Republic of Germany
Nb(Cb) + Ta
3.4.2 Impact Resistance
According to VdTV Material Data Sheet 547, 06.2003, the Impact resistance KV in longitudinal direction is min 85J. (Average value from 3 specimens. The average value may fall short only with one specimen, and only by max. 30%).
4 Application Properties 4.1 Heat Treatment The heat treatment of cold finished DMV 347 HFG comprises a softening heat treatment prior to cold finishing, and a solution heat treatment after final cold finishing. During the hot forming process, the softening is performed using a temperature of min. 50C (90F) above the final solution annealing temperature. The solution annealing of the cold finished tube meets the requirement of VdTV Material Data Sheet 547, where an annealing temperature between 1180C (2150F) and 1250C (2282F) is required and also the requirements of ASME SA-213/SA-213M. Cold formed tubes have to be newly solution annealed if the forming degree is > 20% or the R/D ratio is < or equal 2.5. For corrosion reasons, it is recommended to perform a new solution annealing even following smaller forming degrees. Power Plant Narva 1 Amager Vaerket Unit 1 Qty Del. [t] 100 2002 70 2006 2007 2007
Customers Foster Wheeler Burmeister & Wain Energy Bioener
Fynsvaerket 65 Unit 8 Jyvskyl 96
4.4 Welding Pre-heating and a heat treatment after welding are not necessary. To avoid hot cracks in the weld metal, the processes recommended by the filler producers have to be observed. Only approved filler materials should be considered, that have been tested for the foreseen application temperature. The calculation values for the filler materials should be considered.
Foster Wheeler
Further information on projects is available upon request.
4.2 Corrosion Properties
DMV 347 HFG is designed for the application in furnace atmospheres at high temperature in the range of 580C (1076F) to 640C (1184F) and has a good corrosion resistance in such atmospheres.
5 Specifications and References
DMV 347 HFG may be delivered in accordance with European Steel registration, 1.4908, X8CrNi 19 11, TP347HFG according to ASME SA213/SA-213M, and following VdTV Material Data Sheet 547, 06.2003. Frequently the DMV 347 HFG will be delivered according to project specific customer specifications.
4.3 Tube Bending
DMV 347 HFG is generally suitable for further cold or hot forming. After hot forming a new solution annealing is necessary, in case the hot forming has not followed a controlled temperature process between 1170C (2138F) and 1210C (2210F). SALZGIT TER MANNESMANN S TAINLESS TUBES
Sales Contacts Salzgitter Mannesmann Stainless Tubes Italia S.r.l. Via Pi 30 24062 Costa Volpino (BG) Italy Tel.: +39 035 975 744 Fax: +39 035 975 803 Email: [email protected] Salzgitter Mannesmann Stainless Tubes Deutschland GmbH Wiesenstrae 36 45473 Mlheim an der Ruhr Germany Tel.: +49 208 458 2611 Fax: +49 208 458 2641 Email: [email protected] Salzgitter Mannesmann Stainless Tubes France SAS Route de Semur 21500 Montbard France Tel.: +33 3 80 89 52 00 Fax: +33 3 80 89 52 26 Email: [email protected] Salzgitter Mannesmann Stainless Tubes USA, Inc. 12050 West Little York Houston Texas 77041 USA Tel.: +1 713 466 7278 Fax: +1 713 466 3769 Email: [email protected]
Whilst every care has been taken in compiling the technical information in this brochure, due to the continuing development and complex nature of the various factors used, it is given for information only. Our company cannot be held responsible for the information contained herein and our customers should carefully check for themselves where necessary in order to make the appropriate selection, bearing in mind the conditions governing the fabrication of our alloys as well as the conditions in service. Information held in this datasheet can be changed without notice.
