Scribd
Upload
9 views

Instructions C CSS

Uploaded by

hammouche.idris1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views

Instructions C CSS

Uploaded by

hammouche.idris1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

#define lcd_rs_pin pin_d1 // Define the pin connected to the RS pin of the LCD

#define lcd_rw_pin pin_d2 // Define the pin connected to the RW pin of the LCD
#define lcd_enable_pin pin_d3 // Define the pin connected to the Enable pin of the LCD
#define lcd_data4 pin_d4 // Define the pin for LCD data line D4
#define lcd_data5 pin_d5 // Define the pin for LCD data line D5
#define lcd_data6 pin_d6 // Define the pin for LCD data line D6
#define lcd_data7 pin_d7 // Define the pin for LCD data line D7

#include <16f877a.h>
#device adc = 10 // Configure ADC to use 10-bit resolution
#use delay (clock = 8M) // Set the microcontroller clock frequency to 8 MHz
#include <lcd.C> // Include the LCD driver library
#include <kbd.C> // Include the keyboard (keypad) driver library
#include <math.h> // Include the math library for advanced calculations
#use RS232 (baud=9600, xmit=pin_c6, rcv=pin_c7) // Configure UART communication
#use rtos (timer=n, minor_cycle=m)

unsigned int16 ...; // Placeholder for a 16-bit unsigned integer variable


int ...; // Placeholder for an integer variable
float ...; // Placeholder for a floating-point variable
char ...; // Placeholder for a character variable
double ...; // Placeholder for a double-precision floating-point
variable
int seg[... , ...] = { {... , ...} , {... , ...} }; // Placeholder for a 2D integer array
initialization

#int_RDA // Interrupt
void RDA() {
k = getc(); // Read a character from the Terminal
printf("\n \r caractere recu : %c", k); // Print the received character in the Terminal
...
}

#int_TIMER0 // Interrupt for Timer 0


void timer0_isr() {
set_timer0(PRC);
if (k++ == 250) {
}
...
}

#task(rate=n, max=m, queue=p)


void any_task () {
rtos_wait(sem); // P (Wait on semaphore 'sem')
... // Critical Section
rtos_signal(sem); // V (Signal the semaphore 'sem')

if (rtos_msg_poll() > 0) { // Check if there are any messages in the task's queue.
rtos_msg_read(); // Read a message from the queue if one is available.
}
rtos_msg_send(reciver_name,message_send); // Send a message to another task
rtos_terminate(); // Terminate the task and retuen to the void main()
}
void main() {
while (1) { // Infinite loop for the main program
// Main code logic here
}

set_tris_a(0xff); // Set Port A as input (0xff = all pins input)


set_tris_b(0x00); // Set Port B as output (0x00 = all pins output)
output_b(0x00); // Initialize Port B to 0
output_low(pin_c0); // Set Pin C0 to low
output_high(pin_c0); // Set Pin C0 to high
output_bit(pin_c1,S1); // Set Pin C1 to S1 value
A = input(pin_d1); // Read input from Pin D1
A = input_d(); // Read all inputs from Port D

delay_ms(...); // Placeholder for a delay in milliseconds

enable_interrupts(int_RDA); // Enable receive interrupt


enable_interrupts(GLOBAL); // Enable global interrupts

setup_timer_0(RTCC_INTERNAL | RTCC_DIV_PRD); // Configure Timer 0 with internal clock


and prescaler
enable_interrupts(int_timer0); // Enable Timer 0 interrupt
enable_interrupts(GLOBAL); // Enable global interrupts again

sem = 1;
rtos_run();

setup_adc(adc_clock_internal); // Configure ADC to use internal clock


setup_adc_ports(an0); // Set AN0 as the ADC input channel
set_adc_channel(0); // Select ADC channel 0
V = read_adc(); // Read the ADC value
V = V * 5.00 / 1024; // Convert ADC value to voltage (assuming a 5V reference)

lcd_init(); // Initialize the LCD


lcd_putc('\f'); // Clear the LCD screen
lcd_putc('\a'); // Set cursor position to upper left
lcd_putc('\b'); // Move the cursor one position back
lcd_putc('\n'); // Move the cursor to the next line
lcd_gotoxy(1,1); // Move the LCD cursor to the first row, first column
printf(lcd_putc, "\f \a \b \n ... %3.2f %d %c", ...); // Print formatted data to the
LCD

kbd_init(); // Initialize the keypad


k = kbd_getc(); // Get a character from the keypad
if (k != 0) { // Check if a key was pressed
switch (k) { // Handle keypad input
case ('0'): ...; break; // Action for '0'
case ('1'): ...; break; // Action for '1'
// Cases for other keys
case ('9'): ...; break; // Action for '9'
}
}

if ( ... == ... ) {} // Example conditional statement


if ( ... <= ... ) {} // Example conditional statement
if ( ... >= ... ) {} // Example conditional statement
if ( ... != ... ) {} // Example conditional statement
if ( ... || ... ) {} // Logical OR condition
if ( ... && ... ) {} // Logical AND condition

int i; // Declare a loop counter


for (i = 0; i < 10; i++) { // Loop from 0 to 9
// Loop body
}
}

// keypad blue : rows : 4, 7, 1, 5 ; columns : 2, 3, 6

// 7 seg : E = 0x79 / F = 0x71 / 0 = 0x3F / 1 = 0x06 / 2 = 0x5B / 3 = 0x4F / 4 = 0x66 /


5 = 0x6D / 6 = 0x7D / 7 = 0x07 / 8 = 0x7F / 9 = 0x6F

You might also like