Infrared Trail Camera

User's Manual
Mini-301

Package List:

* Camera X1 * USB Cable X1

* Mounting Strap X1 * User Manual X1

1
Parts Of The Camera
1. Display screen
2. IR lamps
3. Lens
4. Up/Video Button
5. Down/Capture Button
6. Motion sensor
7. OK/Shot button
8. Menu Button
9. Right button
10. Playback button
11. DC adapter port
12. Tripod Slot
13. Micro SD card slot
13. Battery compartment
14. ON-TEST-OFF button
15. USB jack

2
Power Supply
This camera support 2 power supply modes: AA battery and
external power.

1. AA battery: Unlock the camera, you will find the battery

compartment. which need 4 pieces 1.5V AA batteries, and make
sure the battery polarity is correct.

2. At the bottom of camera, there is external power supply port,

which support DC 6V 1A power, power plug size is 3.5X1.35mm

Inserting the Memory Card

 Please prepare a Micro SD card and insert it into the
camera for saving files, and format the memory card
firstly before it is inserted into camera.
 Camera support micro SD card max 32GB ,class6 or
above high speed card is better, doesn't support 64GB.
 To avoid malfunction, the memory card should be far
away from water, strong vibration, dust, hot source and
direct sunlight.

3
 Do not insert the memory card forcibly. Please refer to
the marking on the camera.
 For the first time of use, please wait for the memory
card temperature reach the ambient temperature. The
camera will be short-circuited by environment
temperature and humidity. Please protect the camera
when using it outdoor.
 If the capacity of memory card is full, the camera will
stop recording automatically.
 Press the edge of the card gently to pop-up the Micro
SD card.

Basic Operation
Turn On / Off the Camera
 Switch the Mode Button to “Test” to turn on the
camera.
 Switch the Mode Button to “ON” ,camera start to work
after 5 seconds red flash.
 Switch the Mode Button to “Off” to turn off the camera.

4
System Setup
Switch Mode Button to “Test”, then you can set the system
parameters.
1. Press Menu button to open the setup menu.
2. Press Up / Down button to scan all menus. Then press OK
button to enter the options interface.
3. Press Up / Down button to scan all options. And press OK
button to confirm options.
4. Press Menu button again to turn back to last menu or exit
the setup menu.

You can follow below instructions to setup the menus and

functions:

Mode
Set the working mode, there are 4 modes:
Camera: camera take pictures only.
Video: camera takes videos only.
Camera &video: the camera will take a photo firstly, then take
a video.
Time lapse: camera take pictures/videos every
5/10/30/60minutes, no matter it detect target or not.

5
Resolution
Set the picture resolution, 3 options: 12MP / 8MP / 5MP
Continue Shot
4 options: 1/3/6/9， for example, 3 means camera take 3 pictures
if it is triggered one time.
ISO
4 options, Auto/100/200/400, you can choose 400 to make the
pictures brighter, and choose 100 if you think picture is little
over-exposed.
Video Size
You can choose the video resolution, 3 options: 1080P
/720P/VGA.
Video Length
You can choose video length when camera take a video, 5
options: 10/20/30/60/90 seconds.
Record Audio
2 options: [On]/[Off], when you choose ON, when camera take
a video, camera's microphone will also record the audio.
PIR Interval
Set the time of delay shooting when the camera detects a
motion. In the selected time, the camera will not record any
image or video. it can avoid storing too many the same events
and waste of memory storage.

6
9 options: 1/5/10/15/30 seconds,1/5/10/30 minutes.
PIR sensitivity
Set the sensitivity level of the PIR sensor.
3 options: low / Medium / High
Language
13 options: English / Français / Deutsch / Italiano /Espanol /
Português / Nederlands / Danish / Hrvatski/ Finnish / Swedish /
Poland / Norwegian
Time lapse
If you choose time lapse mode, there are 4 options:
5/ 10 / 30 / 60 minutes.
Over write
2 options: Off / On
When your camera memory card is full, it will delete the first
picture/video, then save a new picture/video, so camera can take
picture/video endlessly.
Date
Set the camera date & time, 3 options:
YY/MM/DD , MM/DD/YY, DD/MM/YY
Camera Name.
6 letters or numbers, for example CAM000
Timer
You can set the camera start and stop time, for example

7
if you want camera just work at night, you can set 18:00:00 to
6:00:00

Password
2 options: Off / On.
When you choose "On", you can fill in your new password in
the "NEW" and press OK to save it.
If you forget the password, there is a universal password
1314, you can reset your password.
Format
All the data including pictures and videos will be deleted.
permanently. when you use a new memory card or a card that has
been used in other device, we suggest that you format the SD card.
Default Setting
Restore the camera to factory default setting.
Version
The firmware number of camera.

Take pictures,videos, Playback

Switch the Mode Button to “Test”. you can take photos, videos
and playback it manually.
 Take Photos: Press "Down" button to switch to photo mode.
Press "Right" button to take a picture manually.
8
 Press "Up" button to switch to video mode. press "Right"
button to take a video manually, press it again to stop.
1) Playback: press "Play" button to enter the playback
interface. Press Up/Down button to scan photos or videos.
When playback a video, press "Right" button to play the
video, press it again to stop
2) Press "Menu" button to delete, protect or slide show.
3) Press "OK" button to exit the playback mode.
 Playback Menu:
1) Delete current file: Delete the current photo or video.
Options: [Cancel]/[Delete].
2) Delete all files: Delete all photo and video files in the
memory card. Options: [Cancel]/[Delete].
3) Activate slide show: Playback the photos in slide way.
Each photo displays 3 seconds. Press OK button to stop
playing.
4) Write protect: Lock the file. It can avoid accidental
deletion. Options: [Write-protect current file]/[Write-
protect all files]/[Unlock current file]/[Unlock all files].
Working Mode
Switch the Mode Button to “On”. camera has red flash for 5
seconds. then camera begins to work.
 If the wild animals enter the detection range of the motion
sensors, the camera will be activated and start to take
pictures or videos.

9
 If the wild animals continue to move to the detection zone of
the sensor, the camera will take photos or record video
automatically.
 When the wild animals leave the detection zone of the
sensors, the camera will be deactivated and turn back to
standby mode.
Night Mode
In night mode, the pictures are white and black mode.
When record a video for long time in the evening, the low
voltage may have a great influence on the stability of the
machine, thus do not record video with low voltage in the
evening.
Connecting the Camcorder to a PC by the USB Cable
1. Connect the camera to the computer via a USB cable. Turn
on the camera, the screen displays “Mass Storage”.
2. Open [My Computer] or [Windows Explorer]. A
"Removable Disk" appears in the drive list. Double-click the
"Removable Disk" icon to view the contents from the
camera.
Please notice - All products are subject to change
without any notice. We take reservations for errors and
omissions in the manual.

10