Installation Instructions

847T 2 in. Diameter Solid Shaft Incremental Encoders

IMPORTANT: SAVE THESE INSTRUCTIONS FOR FUTURE USE.
Selection Guide

847 T
- P Y 1 4
- Rf C 01204 f
a b c d e g h Code Connector/Cable Exit
R Radial exit
a
g
Code Encoder Diameter/Type
Code Connector/Cable Type
T 2 in. diameter, solid shaft
A M12 connector, 8-pin with mating connector
b
B M12 connector, 8-pin
Code Mounting Configuration
C MS connector, 6-pin with mating connector
D Standard square flange
D MS connector, 6-pin
H Standard servo mount
E MS connector, 7-pin with mating connector
P 5 PY mounting*
F MS connector, 7-pin
*P can be ordered only with option Y from table c
G MS connector, 10-pin with mating connector
c
H MS connector, 10-pin
Code Shaft Size
P Cable with 1.5 m (4.92 ft) length
K 6 mm diameter shaft with flat
Q Cable with 5 m (16.4 ft) length
L 10 mm diameter shaft with flat
R Cable with 10 m (32.8 ft) length
M 1/4 in. diameter shaft with flat
h
N 3/8 in. diameter shaft with flat
Code: Resolution
Y 5/8 in. diameter extended shaft with flat**
00001…65536 00001…65536 pulses/revolution
**Y can be ordered only with option P from table b

d Accessories
Code Power Supply Description Part Number

1 4.5…5.5V DC High performance flexible coupling  845-FC-*-*

Measuring wheels  845-MW-A-*
2 8…30V DC
Mounting plates  845-MB-*
e
Servo clamps  845-SC
Code Output Configuration
Pre-wired cables 845-CA-*-*
Signal Phasing A-leads-B, Z gated A Mating connectors 845-6P
4 4.5…5.5V line driver outputs 845-7P
845-7P-RT
5 4.5…5.5V open collector outputs  845-10P
845-10P-RT
6 8…30V line driver outputs 
Differential encoder buffer board 845-BB*
7 8…30V open collector outputs  M12 cable 889D-F8FB-*
Signal Phasing B-leads-A, Z gated BN Not available for PY mounting
* See Sensor Catalog for selection.
A 4.5…5.5V line driver outputs

B 4.5…5.5V open collector outputs  Specifications

C 8…30V line driver outputs  Electrical
D 8…30V open collector outputs  Code format Incremental, 2 channels with zero index
Options 5 and B cannot be ordered with option 2 from table d. Signal options, clockwise A-leads-B, 180° marker gated with A, or
Options 6, 7, C and D cannot be ordered with option 1 from table d. rotation viewed from shaft end B-leads-A, 180° marker gated with BN
Electrical (continued) Mechanical (continued)

Signal phase relation 90° ± 22° channels MTTFd (EN ISO 13849-1) 330 years

Symmetry 50% ± 10% Shaft loading 80 N radial, 20 mm (0.79 in.) from front
bearing and 40 N axial provide L10 life
Zero index channel Gated 1/2 cycle of 3.6 x109 revolutions at 9,000 RPM
and 80 °C ambient temperature
Supply current 50 mA
Shaft diameter [mm (in.)] 6 (0.24), 10 (0.39), 6.4 (0.25), and
Frequency response 4.5…5.5V line driver output: 820 kHz 9.2 (0.38) diameter for solid shaft
8…30V line driver output: 820 kHz encoders
Open collector: 150 kHz 7.94 (0.313) for encoder with PY
Resolution 1…65536 pulses/revolution mounting

Load current 30 mA for all output types Environmental

Output drivers 4.5…5.5V line driver - IC HD2 Enclosure type rating Shaft: IP 65
8…30V line driver - IC HD2 Housing, connector version with
Open collector - 7406 mating connector installed: IP67
Housing, cable version: IP67
Electrical protection Reverse polarity and short circuit for all
output types Temperature -30…80 °C (-22...176 °F) operating
-40…100 °C (-4...212 °F) storage
Cable outer diameter 0.25 in (6.2 mm)
Relative humidity 90% non-condensing
Cable type 300V, 105 °C, 26 AWG, 9-conductor with
overall braided shield, UL AWM type Shock 100G/11 ms duration
20327 for use in fixed (non-flexing)
Vibration 30G/10…2,000 Hz
installations; RoHs compliant
EMC EN 61000-6-2 and EN 61000-6-3
Cable bend radius Minimum 5x outer diameter
(M12 connector)
Mechanical Housing material EN AC-47100 die-cast aluminium
Maximum operating speed 9,000 RPM Housing finish Powder coat paint, color RAL 9005,
Angular acceleration 500,000 radians/s² Pantone black C (jet black)

Moment of inertia 15 g•cm² Flange material 6061-T6 aluminium

Startup torque at 20 °C (68 °F) 0.8 N•cm Shaft material SAE 303 stainless steel

Operating torque at 20 °C (68 °F) 0.6 N•cm Certifications RoHS compliant

CE Marked for all applicable directives,
Approximate weight [kg (lb)] 0.22 (0.50) square flange mounting UL listed only with cable or M12
with M12 connector connections
0.34 (0.75) PY mounting with M12
connector

Output Waveforms
Complementary signals AN, BN, and ZN are supplied only on units with line driver outputs.
Signals and marker option - A leads B (CW rotation) Signals and marker option - B leads A (CW rotation)
90° Measuring step 90° Measuring step
360° 360°

A A

B B

A leads B, 180° B leads A, 180°

Z marker gated with A Z marker gated with BN

Clockwise rotation when facing encoder shaft Clockwise rotation when facing encoder shaft

2
Connector Pins and Signal Availability
Signal Name MS 6-pin MS 7-pin MS 10-pin M12 8-pin Cable wire colors
V DC B D D 8 Red
Common A F F 7 Black with red band
A output E A A 2 White
AN output - - H 1 Black with white band
B output D B B 4 Blue
BN output - - I 3 Black with blue band
Z output C C C 6 Green
ZN output - - J 5 Black with green band
Zero set input - E E - Yellow
Case F G G - Black
5 8
A 6 4
F A H I A
F B
Encoder connectors G B -
E C E G B
F J C 7 3
D C E D
D
1 2

Recommended mating cable

845-CA-A-* 845-CA-B-* 845-CA-C-* 889D-F8FB-* (Attached to encoder)
Cat. No.

Dimensions [mm (in.)]

Square Flange Mounting with Servo Flange Mounting with
Radial M12 Connector Radial M12 Connector
19.1 19.1 ±0.5
Shaft Options (0.75) (0.75±0.02)
Shaft Options
Nominal Shaft dia. , A Flat dim., B Nominal Shaft dia. A Flat dim. B Dia. A
1/4 in. 6.327/6.312 (0.2491/0.2485) 5.5 (0.22) 1/4 in. 6.327/6.312 (0.2491/0.2485) 5.5 (0.22)
3/8 in. 9.507/9.492 (0.3743/0.3737) 8.5 (0.33) 3/8 in. 9.507/9.492 (0.3743/0.3737) 8.5 (0.33)
6 mm 6.000/5.988 (0.2362/0.2357) 5.5 (0.22) 6 mm 6.000/5.988 (0.2362/0.2357) 5.5 (0.22)
10 mm 9.977/9.962 (0.3928/0.3922) 9 (0.35) Dia. A 10 mm 9.977/9.962 (0.3928/0.3922) 9 (0.35)
3.1 3.1 (0.12)
(0.12)
35.9 35.9 (1.41)
52.4 7.6 (1.41) 2.5
(0.30) 29.2 (1.15) 4X 10-32 UNF 5.6 (0.22) (0.10)
(2.06)
4 x dia. 4.0 (0.16) thru 16.0
44.5
(1.75) (0.63)
47.0
42.0 ia. 29.2 (1.85) dia. B 50.8
(1.65) d (1.15) 50.8 (2.00)
44.5 52.4 B 50.8 (2.00) dia. 44.0
(1.75) (2.06) (2.00) dia. (1.73)
44.0 (1 38. 31.70 ±0.03
.50 1
(1.73) )d 1.248 ±0.001 dia.
3X M4x0.7 - 6H ia.
31.70 ±0.03 5.6 (0.22) 2.5 (0.10) 9.0 (0.35)
(1.248 ±0.001) dia. equally spaced 3X 4-40 UNC 5.6 (0.22)
9.0 equally spaced
(0.35)

Square Flange Mounting with Square Flange Mounting Servo Flange Mounting with Servo Flange Mounting with
Radial M12 Connector with RadialCable Radial MS Connector Radial Cable
46.1 35.9
(1.82) (1.41)
46.1 (1.82) 35.9 (1.41)

49.7 49.7
1.96 (1.96)
C C

Cable options
1.5 m (4.9 ft) per part
per part number
number 18.0 5 m (16.4 ft)
18.0 0.71
MS Connector Options (0.71) MS Connector Options 10 m (32.8 ft)
50.0
Type C Cable options Type C (1.97)
50.0
6 pin 63.9 (2.52) 1.5 m (4.9 ft) 1.97 6 pin 63.9 (2.52)
7 pin 63.9 (2.52) 5 m (16.4 ft) 7 pin 63.9 (2.52)
10 pin 69.4 (2.73) 10 m (32.8 ft) 10 pin 69.4 (2.73)

3
Dimensions [mm (in.)] (continued)

0.000
Dia. 7.938 -0.013
0.0000
0.3125 -0.0005

PY Flange Mounting with Radial M12 Connector

24.6
(0.97)

40.7
4 x dia. 7.1 (0.28) thru 90.0° (1.60)
4.8
(0.19)
1.5
(0.06)
12.7
10 (0.50)
(3.9 1.0

45.0
8) d
ia.

° 116.6 63.5
(2.50) 50.8
(4.59) dia.
(2.00) dia.
44.0
(1.73)
7.3
(0.29)

9.0 (0.35)

PY Flange Mounting with Radial MS Connector PY Flange Mounting with Radial Cable

50.9 40.7
2.01 1.60

49.7
(1.96)
C

per part
MS Connector Options number
Type C Cable options
18.0
6 pin 63.9 (2.52) 1.5 m (4.9 ft)
(0.71) 50.0
7 pin 63.9 (2.52) 5 m (16.4 ft) (1.97)
10 pin 69.4 (2.73) 10 m (32.8 ft)

Rockwell Automation maintains current product environmental information on its website at

http//www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

www.rockwel lautomation.com

Power, Control and Information Solutions Headquarters

Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444
Europe/Middle East/Africa: Rockwell Automation NV, Pegasus Park, De Kleetlaan 12a, 1831 Diegem, Belgium, Tel: (32) 2 663 0600, Fax: (32) 2 663 0640
Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846
Copyright 2014 Rockwell Automation, Inc. All rights reserved. 10001065811 Ver 00 Jul7 2014
847T-IN001A-EN-P
Printed in USA