BALT443809
Uploaded by
Jack SparrowBALT443809
Uploaded by
Jack SparrowPROPRIETARY NOTICE THIS DOCUMENT AND ALL INFORMATION HEREIN IS THE CONFIDENTIAL PROPERTY OF BECTON DICKINSON AND COMPANY
AND SHALL NOT BE
COPIED, DISCLOSED TO THIRD PARTIES CONFIDENTIALLY OR NON-CONFIDENTIALLY, PUBLIC DISCLOSED, OR USED FOR ANY PURPOSE OTHER THAN THE SPECIFIC
PURPOSE FOR WHICH IT WAS PROVIDED WITHOUT PRIOR WRITTEN AUTHORIZATION AND SHALL BE DESTROYED OR RETURNED UPON DEMAND.
PROCEDURE:
1. Print Attachments A, B, C, D & E of this document that contain the scanner configuration
instructions for all instrument platforms.
2. Fold printed instructions and place inside (-01) Scanner OEM carton.
3. Seal (-01) Scanner OEM carton with packaging tape.
4. Using in house labeling equipment and item (-02) label, Print Barcode per Spec
BALTMI0436. (See template instructions drawing 011-830).
PRIMARY BAR CODE
(01)00382904438098
DESCRIPTION LINE 1: SCANNER BARCODE
DESCRIPTION LINE 2: HANDHELD PACKAGED
5. Apply printed label to carton (Lower right corner of largest side panel).
1 -02 LABEL- BLANK 0001-600-015 0001-600-015
1 -01 SCANNER BALT246-1352 500008071
QTY ITEM DESCRIPTION DRAWING SAP P/N
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED, DIM ARE IN
INCHES. TOL ON ANGLE + 0.5, 2 PL + .02, 3 PL
+ .005, 4 PL + .0005 HOLE DIAMETERS + .005. BD DIAGNOSTIC SYSTEMS
INTERPRET DIM AND TOL PER Y 14.5M – 2009. BECTON, DICKINSON AND COMPANY
SPARKS, MARYLAND 21152
SCANNER BARCODE HANDHELD PACKAGED
SAP PART NUMBER:443809 SIZE DRAWING NUMBER REV
MODEL VERSION:-
MODEL BY:- A BALT443809 2
DRAWING BY: J. MILES
NEXT ASSY: - SCALE = 1:1 DO NOT SCALE DRAWING SHEET 1 OF 8
Attachment A
Scanners: 500008071 / 443809
EpiCenter Configuration Guide
1) For configuring scanner for EpiCenter connect scanner USB connector to active USB port on PC.
2) Scan the following 3 barcodes in order.
Standard Product Default Settings
USB HID (PC)
Add CR Suffix All Symbologies
3) Disconnect scanner from USB port. Reconnect scanner to USB port (this will force software
drivers to update).
4) Log into Epicenter and open the Bactec Media Lot and Expiration purchasable module.
5)
6) Once the module is open select the “Scanner” icon by clicking on it.
Attachment A - EpiCenter SHEET 1 of 2 .
Drawing Number BALT443809 Rev. 2 SHEET 2 of 8 .
7) Once the “Scanner” has been selected you will be prompted to register the scanner by scanning
any barcode.
8) Once registered the “Change Mode” icon will no longer be grayed out and the scanner will be fully
functional.
Note: Rebooting the system may be required for PC to recognize scanner.
Attachment A - EpiCenter SHEET 2 of 2 .
Drawing Number BALT443809 Rev. 2 SHEET 3 of 8 .
Attachment B
Scanners: 500008071 / 443809
Viper LT Configuration Guide
1. For configuring scanner for Viper LT connect scanner USB connector to active USB port on PC or
instrument. (Note: Instrument software version must be V2.93 or higher to use this scanner.)
2. Scan the following 4 barcodes in order.
Standard Product Default Settings
USB HID (PC)
Windows Mode Control
+ ASCII Mode ON
Add CR Suffix All Symbologies
3. Disconnect scanner from USB port.
4. Reconnect scanner to USB port (this will force software drivers to update).
Note: Rebooting the system may be required for instrument/computer to recognize scanner.
Attachment B - Viper LT SHEET 1 of 1 .
Drawing Number BALT443809 Rev. 2 SHEET 4 of 8 .
Attachment C
Scanners: 500008071 / 443809
Totalys (FEA) Configuration Guide
1) For configuring scanner for Totalys (FEA) connect scanner USB connector to active USB port on
PC or instrument.
(Note: Totalys (FEA) Instrument software version must be V1.5 or higher to use this scanner.)
2) Scan the following 3 barcodes in order.
Standard Product Default Settings
USB HID (PC)
Add CR Suffix All Symbologies
3) Disconnect scanner from USB port.
4) Reconnect scanner to USB port (this will force software drivers to update).
Note: Rebooting the system may be required for instrument/computer to recognize scanner.
Attachment C - Totalys (FEA) SHEET 1 of 1 .
Drawing Number BALT443809 Rev. 2 SHEET 5 of 8 .
Attachment D
Scanners: 500008071 / 443809
Bactec FX40 Configuration Guide
Note: The scanners factory default settings should work properly for the Bactec FX 40 system.
If the scanner does not work properly configure per the following instructions.
1) For configuring scanner for Bactec FX40 connect scanner USB connector to active USB port.
2) Scan the following 2 barcodes in order.
Standard Product Default Settings
USB Virtual COM
3) Disconnect scanner from USB port.
4) Reconnect scanner to USB port (this will force software drivers to update).
Note: Rebooting the system may be required for instrument/tablet to recognize scanner.
Attachment D - Bactec FX40 SHEET 1 of 1 .
Drawing Number BALT443809 Rev. 2 SHEET 6 of 8 .
Attachment E
Scanners: 500008071 / 443809
Phoenix M50 Configuration Guide
1) For configuring scanner for Phoenix M50 connect scanner USB connector to active USB port on
All-In-One PC or instrument.
2) Scan the following 11 (Eleven) barcodes in order.
Standard Product Default Settings
USB HID (PC)
Clear All Prefix
Add Prefix
(Symbology UCC/EAN-128 code ID 0x49)
4
Attachment E - Phoenix M50 SHEET 1 of 2 .
Drawing Number BALT443809 Rev. 2 SHEET 7 of 8 .
(Add AIM I.D., scan 5, C, 8, 1)
5
Save
3) Now verify barcode scanner is correctly programmed. Navigate to the Panel Login Screen. Select
QC panel type. Touch the ID Broth Lot Number field and scan the barcode below
“1234567” should appear in the ID Broth Lot Number field and “1/31/2035” should be in the ID
Broth Expiration Date field. If the lot number and date fields are not populated, re-scan the 11
barcodes in step 2 above and verify again.
Press “cancel” to exit the Panel Login screen.
Attachment E - Phoenix M50 SHEET 2 of 2 .
Drawing Number BALT443809 Rev. 2 SHEET 8 of 8 .
REVISION HISTORY TABLE
Change Revision Version
Originator Summary of Change
Number Number Letter
Mike Bortner 5_39144 1 A Initial Release
Ed Skevington 5_72303 2 B Added Attachment E - Phoenix M50
scanner instructions.
