Scribd
Upload
25 views9 pages

Selfstudys Com File

Uploaded by

viswathivakar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
25 views9 pages

Selfstudys Com File

Uploaded by

viswathivakar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

Network Theory

Current: Electric current is the time rate of change of charge flow.

• Charge transferred between time to and t

Sign Convention: A negative current of –5A flowing in one direction is same as a


current of +5A in opposite direction.
Voltage: Voltage or potential difference is the energy required to move a unit
charge through an element, measured in volts.

Power: It is time rate of expending or absorbing energy.

• Law of conservation of energy must be obeyed in any electric circuit.


• Algebraic sum of power in a circuit, at any instant of time, must be zero.
i.e. ΣP = 0
Circuit Elements:
Passive element: If it is not capable of delivering energy, then it is passive
element. Example: Resistor, Inductor, and Capacitor
Active element: If an element is capable of delivering energy independently, then
it is called active element. Example: Voltage source, and Current source.

Linear and Non linear elements: If voltage and current across an element are
related to each other through a constant coefficient then the element is called as
linear element otherwise it is called as non-linear.
Unidirectional and Bidirectional: When elements characteristics are independent
of direction of current then element is called bi-directional element otherwise it is
called as unidirectional.
• R, L & C are bidirectional
• Diode is a unidirectional element.
• Voltage and current sources are also unidirectional elements.
• Every linear element should obey the bi-directional property but vice versa
as is not necessary.

Resistor: Linear and bilateral (conduct from both direction)


• In time domain V(t) = I(t)R
• In s domain: V(s) = RI(s)

• l = length of conductor, ρ= resistivity, A = area of cross section


• Extension of wire to n times results in increase in resistance:

• Compression of wire results in decrease in resistance:

Capacitor: All capacitors are linear and bilateral, except electrolytic capacitor
which is unilateral.
• Time Domain:

• In s-domain:

• Capacitor doesn’t allow sudden change of voltage, until impulse of


current is applied.
• It stores energy in the form of electric field and power dissipation in ideal
capacitor is zero.
Impedance:

Inductor: Linear and bilinear element

• Inductor doesn’t allowed sudden change of current, until impulse of


voltage is applied. It stores energy in the form of magnetic field.
• Power dissipation in ideal inductor is zero.
Mesh Analysis:
• Path - A set of element that may be traversed in order, without passing thru
the same node twice
• Loop - a closed path
• Mesh - A loop that does not contain any other loop within it
• Planar Circuit - A circuit that may be drawn on a plane surface in such a way
that there are no branch crossovers
• Non-Planar Circuit - A circuit that is not planar, i.e, some branch(es) pass
over some other branch(es) (Can not use Mesh Analysis)

Transformer: 4 terminal or 2-port devices.

• N1 > N2 : Step down transformer

• N2 > N1 : Step up transformer


• Transformer doesn’t work as amplifier because current decreases in same
amount power remain constant.

Gyrator:

• R0 = Coefficient of Gyrator
• V1=R0I2
• V2= - R0 I1
• If load is capacitive then input impedance will be inductive and vice versa.
• If load is inductive then input impedance will be capacitive.
• It is used for simulation of equivalent value of inductance.

Voltage Source:
• In practical voltage source, there is small internal resistance, so voltage
across the element varies with respect to current.

• Ideal voltmeter, RV is infinite (Internal resistance)


Current Source:

• In practical current source, there is small internal resistance, so current


varies with respect to the voltage across element

• Ideal Ammeter, Ra is 0 (Internal resistance)


• Internal resistance of voltage source is in series with the source.
• Internal resistance of ideal voltage source is zero.
• Internal resistance of current source is in parallel with the source.
• Internal resistance of ideal current source is infinite.

Independent Source: Voltage or current source whose values doesn’t depend on


any other parameters.
• Example: Generator
Dependent Source: Voltage or current source whose values depend upon other
parameters like current, voltage.

Lumped Network: A network in which all network elements are physically


separable is known as lumped network.

Distributed network: A network in which the circuit elements like resistance,


inductance etc, are not physically separate for analysis purpose, is called
distributed network. Example: Transmission line.

Thevenin's Theorem: Any linear network can be replaced by an independent


voltage sources in series with an impedance such that the current voltage relation at
the terminals is unchanged.

Norton's Theorem: Identical to thevenin's statement except that the equivalent


circuit is an independent current source in parallel with an impedance. (ZS = RTh)

You might also like