LM119, LM219, LM319

High-speed dual comparators

Datasheet - production data

Features
• Two independent comparators
• Supply voltage: +5 V to ±15 V
• Typically 80 ns response time at ±15 V
• Minimum fan-out of two each side
DIP14 • Maximum input current of 1 µA over the
(plastic package) operating temperature range
• Inputs and outputs can be isolated from system
ground
• High common-mode slew rate

SO-14 Description
(plastic micropackage)
These products are precision high-speed dual
comparators designed to operate over a wide
range of supply voltages down to a single 5 V
logic supply and ground. They feature low input
N.C. 1 14 N.C. currents and high gains.
N.C. 2 13 N.C. The open collector of the output stage makes
Ground 1 3 12 Output 1
them compatible with transistor-transistor logic
(TTL) as well as capable of driving lamps and
-inverting input 1 4 11 V
CC
+ relays at currents up to 25 mA.
Inverting input 1 5 10 Inverting input 2
Although designed primarily for applications
V
CC
- 6 9 Non-inverting inp requiring operation from digital logic supplies,
these comparators are fully specified for power
8 Ground 2
Output 2 7
supplies up to ±15 V.
Pin connections They feature faster response times than the
(top view) LM111 at the expense of higher current
consumption. However, the high speed, wide
operating voltage range and low package count
make the LM119, LM219, and LM319 much more
versatile.

March 2013 DocID2155 Rev 3 1/13

This is information on a product in full production. www.st.com 13
Contents LM119, LM219, LM319

Contents

1 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4

3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Typical application diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1 DIP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2 SO-14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

6 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2/13 DocID2155 Rev 3

LM119, LM219, LM319 Schematic diagram

1 Schematic diagram

Figure 1. Circuit schematics (1/2 LM119)

R1
3.5kΩ
+
V CC

R7
3kΩ
R3 R6
4kΩ 3kΩ
Q9
R2
4kΩ

Q4
Q8

Q3
Q7

R12
Q6
13kΩ
c1 R11
18μF 13kΩ
Inverting
- Q2
Input

R4 R5 R10
3kΩ 3kΩ 470kΩ

R8
Non-inverting + Q1 2kΩ
Input

Q6

Q15

Q10
R9 Q13
18kΩ R15
300Ω
Q22

R23 R22 R13 Output

Q14
4kΩ 60Ω 600Ω
R18
R20 1.8kΩ
3.6kΩ
Q21 Q16
Q11 Q12
Q20
R19 R16
R25 R14 600Ω
250Ω
600Ω 2kΩ

Q19
R24
250Ω
Q17
R21
Q18
900Ω
R17
3Ω

To other half V CC - GND

DocID2155 Rev 3 3/13

Absolute maximum ratings and operating conditions LM119, LM219, LM319

2 Absolute maximum ratings and operating conditions

Table 1. Absolute maximum ratings (AMR)

Symbol Parameter Value Unit

Vo - VCC- Output to negative supply voltage 36

VCC- Negative supply voltage -25
VCC+ Positive supply voltage 18 V
Vid Differential input voltage ±5
Vi (1)
Input voltage ±15
Output short-circuit to ground Infinite
Tj Maximum junction temperature 150
°C
Tstg storage temperature range -65 to +150
Thermal resistance junction to ambient (2)(3)
Rthja DIP14 80
SO-14 105
°C/W
Thermal resistance junction to case (2)(3)
Rthjc DIP14 33
SO-14 31
HBM: human body model(4) 400
ESD MM: machine model(5) 100 V
CDM: charged device model(6) 1500
1. For supply voltages lower than ±15 V the absolute maximum input voltage is equal to the supply voltage.
2. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-
circuits on all amplifiers.
3. Rth are typical values.
4. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
all couples of pin combinations with other pins floating.
5. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two
pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin
combinations with other pins floating.
6. Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.

Table 2. Operating conditions

Symbol Parameter Value Unit

VCC Supply voltage 5 to ±15 V

Operating free-air temperature range
Toper LM119 -55 to + 125 °C
LM219 -45 to + 105
LM319 0 to + 70

4/13 DocID2155 Rev 3

LM119, LM219, LM319 Electrical characteristics

3 Electrical characteristics

Table 3. VCC = ±15 V, Tamb = +25 °C (unless otherwise specified)

LM119, LM219 LM319
Symbol Parameter Unit
Min. Typ. Max. Min Typ. Max.

Input offset voltage (Rs ≤ 5 kΩ)(1)(2) 0.7 4 2 8

Vio mV
Tmin ≤ Tamb ≤ Tmax 7 10
Input offset current (1) 30 75 80 200
Iio
Tmin ≤ Tamb ≤ Tmax 100 300
nA
Input bias current (1) 150 500 250 1000
Iib
Tmin ≤ Tamb ≤ Tmax 1000 1200
Avd Large signal voltage gain 10 40 8 40 V/mV
Positive supply current
ICC+ VCC = ±15 V 8 11.5 8 12.5
VCC+ = +5 V, VCC- = 0 V 4.3 4.3 mA

ICC- Negative supply current 3 4.5 3 5

Input common mode voltage range
Vicm VCC = ±15 V ±12 ±13 ±12 ±13
VCC+ = +5 V, VCC- = 0 V 1 3 1 3
Low level output voltage
Io = 25 mA
Vi ≤ -5 mV 0.75 1.5 V
Vi ≤ -10 mV 0.75 1.5
VOL
Tmin ≤ Tamb ≤ Tmax
VCC+ ≥ +4.5 V, VCC- = 0 V, Io(sink) < 3.2 mA
Vi ≤ -6 mV
Vi ≤ -10 mV 0.23 0.4 0.3 0.4
High level output current (Vo = +35 V)
Vi ≥ 5 mV 0.2 2
IOH μA
Vi ≥ 10 mV 0.2 10
Tmin ≤Tamb ≤Tmax, Vi ≥ 5 mV 1 10
tres Response time (3) 80 80 ns
1. These specifications apply for VCC = ±15 V, unless otherwise stated.The offset voltage, offset current and bias current
specifications apply for any supply voltage from a single +5 V up to ±15 V supplies. The offset voltages and offset current
given are the maximum values required to drive the output down to 1V or up to +14 V with a 1 mA load current. Thus, these
parameters define an error band and take into account the worst case effects of voltage gain and input impedance.
2. At output switch point, Vo ≈ 1.4 V, no load, with VCC from 5 V to ±15 V and over the full input common-mode range.
3. The response time specified is for a 100 mV input step with 5 mV overdrive.

DocID2155 Rev 3 5/13

Electrical characteristics LM119, LM219, LM319

Figure 2. Input bias currents (LM119, LM219) Figure 3. Common mode limits (LM119, LM219)

Figure 4. Output saturation voltage Figure 5. Supply current

(LM119, LM219) (LM119, LM219)

Figure 6. Supply current (LM119, LM219) Figure 7. Output limiting characteristics

(LM119, LM219)

6/13 DocID2155 Rev 3

LM119, LM219, LM319 Electrical characteristics

Figure 8. Input bias currents (LM319) Figure 9. Common mode limits (LM319)

Figure 10. Output saturation voltage (LM319) Figure 11. Supply current (LM319)

Figure 12. Transfer function Figure 13. Input characteristics

DocID2155 Rev 3 7/13

Electrical characteristics LM119, LM219, LM319

Figure 14. Response time on falling edge, Figure 15. Response time on rising edge,
VCC = ±15 V VCC = ±5 V

Figure 16. Response time on falling edge, Figure 17. Response time on rising edge,
VCC = ±5 V VCC = ±15 V

8/13 DocID2155 Rev 3

LM119, LM219, LM319 Typical application diagrams

4 Typical application diagrams

Figure 18. Relay driver

+28V

+5V

1/2
Inputs LM119

30V

Figure 19. Window detector

500 Ω
V UT
1/2 VO
LM119
VI
TTL output

1/2
LM119
V LT

V O = +5V for V LT < V I < V UT

V O = 0 for V I < V LT or V I > V UT

DocID2155 Rev 3 9/13

Package information LM119, LM219, LM319

5 Package information

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.

5.1 DIP14 package information

Figure 20. DIP14 package mechanical drawing

Table 4. DIP14 package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

a1 0.51 0.020
B 1.39 1.65 0.055 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 15.24 0.600
F 7.1 0.280
I 5.1 0.201
L 3.3 0.130
Z 1.27 2.54 0.050 0.100

10/13 DocID2155 Rev 3

LM119, LM219, LM319 Package information

5.2 SO-14 package information

Table 5. SO-14 package mechanical drawing

Table 6. SO-14 package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 1.75 0.068
a1 0.1 0.2 0.003 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 8.55 8.75 0.336 0.344
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.68 0.026
S 8° (max.)

DocID2155 Rev 3 11/13

Ordering information LM119, LM219, LM319

6 Ordering information

Figure 21. Order codes

Order code Temperature range Package Packaging Marking

LM119N DIP14 Tube LM119N

LM119D -55 °C to +125 °C Tube or
SO-14 119
LM119DT Tape and reel
LM219N DIP14 Tube LM219N
LM219D -45 °C to +105 °C Tube or
SO-14 219
LM219DT Tape and reel
LM319N DIP14 Tube LM319N
LM319D 0 °C to +70 °C Tube or
SO-14 319
LM319DT Tape and reel

7 Revision history

Figure 22. Document revision history

Date Revision Changes

5-Jul-2002 1 Initial release.

Added ESD, Rthja parameters in Table 1: Absolute maximum ratings
(AMR).
28-Jan-2007 2
Expanded orderable parts table, see Table 21: Order codes.
Updated document format.
Minimum operating temperature changed from -40 °C to -45 °C.
26-Mar-2013 3
Updated titles of Figure 14, Figure 15, Figure 16, and Figure 17.

12/13 DocID2155 Rev 3

LM119, LM219, LM319

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2013 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com

DocID2155 Rev 3 13/13